I started out by augmenting the STE DMA40 driver to get
its LCPA SRAM memory from a proper SRAM handle in the
device tree instead of as a reg cell, and then I saw
that the driver was in a bit of sad state so I did a bit
of cleanups on top.
Signed-off-by: Linus Walleij <[email protected]>
---
Changes in v2:
- Amendments to the bindings after review.
- Link to v1: https://lore.kernel.org/r/[email protected]
---
Linus Walleij (8):
dt-bindings: dma: dma40: Prefer to pass sram through phandle
dmaengine: ste_dma40: Get LCPA SRAM from SRAM node
dmaengine: ste_dma40: Add dev helper variable
dmaengine: ste_dma40: Remove platform data
dmaengine: ste_dma40: Pass dev to OF function
dmaengine: ste_dma40: Use managed resources
dmaengine: ste_dma40: Return error codes properly
ARM: dts: ux500: Add eSRAM nodes
.../devicetree/bindings/dma/stericsson,dma40.yaml | 36 ++-
arch/arm/boot/dts/ste-dbx5x0.dtsi | 73 ++++-
drivers/dma/Kconfig | 1 +
drivers/dma/ste_dma40.c | 336 +++++++++------------
.../dma-ste-dma40.h => drivers/dma/ste_dma40.h | 101 +------
drivers/dma/ste_dma40_ll.c | 3 +-
6 files changed, 254 insertions(+), 296 deletions(-)
---
base-commit: fe15c26ee26efa11741a7b632e9f23b01aca4cc6
change-id: 20230417-ux500-dma40-cleanup-fe4f8d9b19c5
Best regards,
--
Linus Walleij <[email protected]>
Instead of passing the reserved SRAM as a "reg" field
look for a phandle to the LCPA SRAM memory so we can
use the proper SRAM device tree bindings for the SRAM.
Signed-off-by: Linus Walleij <[email protected]>
---
drivers/dma/Kconfig | 1 +
drivers/dma/ste_dma40.c | 47 ++++++++++++++++++++++++-----------------------
2 files changed, 25 insertions(+), 23 deletions(-)
diff --git a/drivers/dma/Kconfig b/drivers/dma/Kconfig
index fb7073fc034f..37db3dc9a92a 100644
--- a/drivers/dma/Kconfig
+++ b/drivers/dma/Kconfig
@@ -553,6 +553,7 @@ config STE_DMA40
bool "ST-Ericsson DMA40 support"
depends on ARCH_U8500
select DMA_ENGINE
+ select SRAM
help
Support for ST-Ericsson DMA40 controller
diff --git a/drivers/dma/ste_dma40.c b/drivers/dma/ste_dma40.c
index f093e08c23b1..236269d35a53 100644
--- a/drivers/dma/ste_dma40.c
+++ b/drivers/dma/ste_dma40.c
@@ -19,6 +19,7 @@
#include <linux/pm_runtime.h>
#include <linux/err.h>
#include <linux/of.h>
+#include <linux/of_address.h>
#include <linux/of_dma.h>
#include <linux/amba/bus.h>
#include <linux/regulator/consumer.h>
@@ -3506,9 +3507,11 @@ static int __init d40_probe(struct platform_device *pdev)
{
struct stedma40_platform_data *plat_data = dev_get_platdata(&pdev->dev);
struct device_node *np = pdev->dev.of_node;
+ struct device_node *np_lcpa;
int ret = -ENOENT;
struct d40_base *base;
struct resource *res;
+ struct resource res_lcpa;
int num_reserved_chans;
u32 val;
@@ -3535,37 +3538,37 @@ static int __init d40_probe(struct platform_device *pdev)
spin_lock_init(&base->interrupt_lock);
spin_lock_init(&base->execmd_lock);
- /* Get IO for logical channel parameter address */
- res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "lcpa");
- if (!res) {
- ret = -ENOENT;
- d40_err(&pdev->dev, "No \"lcpa\" memory resource\n");
- goto destroy_cache;
+ /* Get IO for logical channel parameter address (LCPA) */
+ np_lcpa = of_parse_phandle(np, "sram", 0);
+ if (!np_lcpa) {
+ dev_err(&pdev->dev, "no LCPA SRAM node\n");
+ goto report_failure;
}
- base->lcpa_size = resource_size(res);
- base->phy_lcpa = res->start;
-
- if (request_mem_region(res->start, resource_size(res),
- D40_NAME " I/O lcpa") == NULL) {
- ret = -EBUSY;
- d40_err(&pdev->dev, "Failed to request LCPA region %pR\n", res);
- goto destroy_cache;
+ /* This is no device so read the address directly from the node */
+ ret = of_address_to_resource(np_lcpa, 0, &res_lcpa);
+ if (ret) {
+ dev_err(&pdev->dev, "no LCPA SRAM resource\n");
+ goto report_failure;
}
+ base->lcpa_size = resource_size(&res_lcpa);
+ base->phy_lcpa = res_lcpa.start;
+ dev_info(&pdev->dev, "found LCPA SRAM at 0x%08x, size 0x%08x\n",
+ base->phy_lcpa, base->lcpa_size);
/* We make use of ESRAM memory for this. */
val = readl(base->virtbase + D40_DREG_LCPA);
- if (res->start != val && val != 0) {
+ if (base->phy_lcpa != val && val != 0) {
dev_warn(&pdev->dev,
- "[%s] Mismatch LCPA dma 0x%x, def %pa\n",
- __func__, val, &res->start);
+ "[%s] Mismatch LCPA dma 0x%x, def %08x\n",
+ __func__, val, base->phy_lcpa);
} else
- writel(res->start, base->virtbase + D40_DREG_LCPA);
+ writel(base->phy_lcpa, base->virtbase + D40_DREG_LCPA);
- base->lcpa_base = ioremap(res->start, resource_size(res));
+ base->lcpa_base = ioremap(base->phy_lcpa, base->lcpa_size);
if (!base->lcpa_base) {
ret = -ENOMEM;
d40_err(&pdev->dev, "Failed to ioremap LCPA region\n");
- goto destroy_cache;
+ goto release_base;
}
/* If lcla has to be located in ESRAM we don't need to allocate */
if (base->plat_data->use_esram_lcla) {
@@ -3678,9 +3681,7 @@ static int __init d40_probe(struct platform_device *pdev)
if (base->lcpa_base)
iounmap(base->lcpa_base);
- if (base->phy_lcpa)
- release_mem_region(base->phy_lcpa,
- base->lcpa_size);
+release_base:
if (base->phy_start)
release_mem_region(base->phy_start,
base->phy_size);
--
2.40.0
Extend the DMA40 bindings so that we can pass two SRAM
segments as phandles instead of directly referring to the
memory address in the second reg cell. This enables more
granular control over the SRAM, and adds the optiona LCLA
SRAM segment as well.
Deprecate the old way of passing LCPA as a second reg cell,
make sram compulsory.
Signed-off-by: Linus Walleij <[email protected]>
---
ChangeLog v1->v2:
- Enumerate phandles using inner and outer maxItems as specified
by Rob.
- Drop quotes around reference.
---
.../devicetree/bindings/dma/stericsson,dma40.yaml | 36 +++++++++++++++++-----
1 file changed, 28 insertions(+), 8 deletions(-)
diff --git a/Documentation/devicetree/bindings/dma/stericsson,dma40.yaml b/Documentation/devicetree/bindings/dma/stericsson,dma40.yaml
index 64845347f44d..1e5752b19a49 100644
--- a/Documentation/devicetree/bindings/dma/stericsson,dma40.yaml
+++ b/Documentation/devicetree/bindings/dma/stericsson,dma40.yaml
@@ -112,14 +112,23 @@ properties:
- const: stericsson,dma40
reg:
- items:
- - description: DMA40 memory base
- - description: LCPA memory base
+ oneOf:
+ - items:
+ - description: DMA40 memory base
+ - items:
+ - description: DMA40 memory base
+ - description: LCPA memory base, deprecated, use eSRAM pool instead
+ deprecated: true
+
reg-names:
- items:
- - const: base
- - const: lcpa
+ oneOf:
+ - items:
+ - const: base
+ - items:
+ - const: base
+ - const: lcpa
+ deprecated: true
interrupts:
maxItems: 1
@@ -127,6 +136,15 @@ properties:
clocks:
maxItems: 1
+ sram:
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+ description: A phandle array with inner size 1 (no arg cells).
+ First phandle is the LCPA (Logical Channel Parameter Address) memory.
+ Second phandle is the LCLA (Logical Channel Link base Address) memory.
+ maxItems: 2
+ items:
+ maxItems: 1
+
memcpy-channels:
$ref: /schemas/types.yaml#/definitions/uint32-array
description: Array of u32 elements indicating which channels on the DMA
@@ -138,6 +156,7 @@ required:
- reg
- interrupts
- clocks
+ - sram
- memcpy-channels
additionalProperties: false
@@ -149,8 +168,9 @@ examples:
#include <dt-bindings/mfd/dbx500-prcmu.h>
dma-controller@801c0000 {
compatible = "stericsson,db8500-dma40", "stericsson,dma40";
- reg = <0x801c0000 0x1000>, <0x40010000 0x800>;
- reg-names = "base", "lcpa";
+ reg = <0x801c0000 0x1000>;
+ reg-names = "base";
+ sram = <&lcpa>, <&lcla>;
interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
#dma-cells = <3>;
memcpy-channels = <56 57 58 59 60>;
--
2.40.0
The OF platform data population function only wants to
use struct device *dev, so pass that instead.
This change makes the compiler realize that the local
platform data variable is unused, so drop that too.
Signed-off-by: Linus Walleij <[email protected]>
---
drivers/dma/ste_dma40.c | 13 ++++++-------
1 file changed, 6 insertions(+), 7 deletions(-)
diff --git a/drivers/dma/ste_dma40.c b/drivers/dma/ste_dma40.c
index e5df28cdc4c8..fe98f12b8130 100644
--- a/drivers/dma/ste_dma40.c
+++ b/drivers/dma/ste_dma40.c
@@ -3480,14 +3480,14 @@ static int __init d40_lcla_allocate(struct d40_base *base)
return ret;
}
-static int __init d40_of_probe(struct platform_device *pdev,
+static int __init d40_of_probe(struct device *dev,
struct device_node *np)
{
struct stedma40_platform_data *pdata;
int num_phy = 0, num_memcpy = 0, num_disabled = 0;
const __be32 *list;
- pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
+ pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
if (!pdata)
return -ENOMEM;
@@ -3500,7 +3500,7 @@ static int __init d40_of_probe(struct platform_device *pdev,
num_memcpy /= sizeof(*list);
if (num_memcpy > D40_MEMCPY_MAX_CHANS || num_memcpy <= 0) {
- d40_err(&pdev->dev,
+ d40_err(dev,
"Invalid number of memcpy channels specified (%d)\n",
num_memcpy);
return -EINVAL;
@@ -3515,7 +3515,7 @@ static int __init d40_of_probe(struct platform_device *pdev,
num_disabled /= sizeof(*list);
if (num_disabled >= STEDMA40_MAX_PHYS || num_disabled < 0) {
- d40_err(&pdev->dev,
+ d40_err(dev,
"Invalid number of disabled channels specified (%d)\n",
num_disabled);
return -EINVAL;
@@ -3526,7 +3526,7 @@ static int __init d40_of_probe(struct platform_device *pdev,
num_disabled);
pdata->disabled_channels[num_disabled] = -1;
- pdev->dev.platform_data = pdata;
+ dev->platform_data = pdata;
return 0;
}
@@ -3534,7 +3534,6 @@ static int __init d40_of_probe(struct platform_device *pdev,
static int __init d40_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
- struct stedma40_platform_data *plat_data = dev_get_platdata(dev);
struct device_node *np = pdev->dev.of_node;
struct device_node *np_lcpa;
int ret = -ENOENT;
@@ -3544,7 +3543,7 @@ static int __init d40_probe(struct platform_device *pdev)
int num_reserved_chans;
u32 val;
- if (d40_of_probe(pdev, np)) {
+ if (d40_of_probe(dev, np)) {
ret = -ENOMEM;
goto report_failure;
}
--
2.40.0
This switches the DMA40 driver to use a bunch of managed
resources and strip down the errorpath.
The result is pretty neat and makes the driver way more
readable.
Signed-off-by: Linus Walleij <[email protected]>
---
drivers/dma/ste_dma40.c | 180 ++++++++++++++++--------------------------------
1 file changed, 61 insertions(+), 119 deletions(-)
diff --git a/drivers/dma/ste_dma40.c b/drivers/dma/ste_dma40.c
index fe98f12b8130..c5991009d3e4 100644
--- a/drivers/dma/ste_dma40.c
+++ b/drivers/dma/ste_dma40.c
@@ -554,8 +554,6 @@ struct d40_gen_dmac {
* @virtbase: The virtual base address of the DMA's register.
* @rev: silicon revision detected.
* @clk: Pointer to the DMA clock structure.
- * @phy_start: Physical memory start of the DMA registers.
- * @phy_size: Size of the DMA register map.
* @irq: The IRQ number.
* @num_memcpy_chans: The number of channels used for memcpy (mem-to-mem
* transfers).
@@ -599,8 +597,6 @@ struct d40_base {
void __iomem *virtbase;
u8 rev:4;
struct clk *clk;
- phys_addr_t phy_start;
- resource_size_t phy_size;
int irq;
int num_memcpy_chans;
int num_phy_chans;
@@ -3128,65 +3124,58 @@ static int __init d40_phy_res_init(struct d40_base *base)
return num_phy_chans_avail;
}
+/* Called from the registered devm action */
+static void d40_drop_kmem_cache_action(void *d)
+{
+ struct kmem_cache *desc_slab = d;
+
+ kmem_cache_destroy(desc_slab);
+}
+
static struct d40_base * __init d40_hw_detect_init(struct platform_device *pdev)
{
struct stedma40_platform_data *plat_data = dev_get_platdata(&pdev->dev);
struct device *dev = &pdev->dev;
struct clk *clk;
void __iomem *virtbase;
- struct resource *res;
struct d40_base *base;
int num_log_chans;
int num_phy_chans;
int num_memcpy_chans;
- int clk_ret = -EINVAL;
int i;
u32 pid;
u32 cid;
u8 rev;
+ int ret;
- clk = clk_get(dev, NULL);
- if (IS_ERR(clk)) {
- d40_err(dev, "No matching clock found\n");
- goto check_prepare_enabled;
- }
-
- clk_ret = clk_prepare_enable(clk);
- if (clk_ret) {
- d40_err(dev, "Failed to prepare/enable clock\n");
- goto disable_unprepare;
- }
+ clk = devm_clk_get_enabled(dev, NULL);
+ if (IS_ERR(clk))
+ return NULL;
/* Get IO for DMAC base address */
- res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "base");
- if (!res)
- goto disable_unprepare;
-
- if (request_mem_region(res->start, resource_size(res),
- D40_NAME " I/O base") == NULL)
- goto release_region;
-
- virtbase = ioremap(res->start, resource_size(res));
- if (!virtbase)
- goto release_region;
+ virtbase = devm_platform_ioremap_resource_byname(pdev, "base");
+ if (IS_ERR(virtbase)) {
+ dev_err(dev, "No IO base defined\n");
+ return NULL;
+ }
/* This is just a regular AMBA PrimeCell ID actually */
for (pid = 0, i = 0; i < 4; i++)
- pid |= (readl(virtbase + resource_size(res) - 0x20 + 4 * i)
+ pid |= (readl(virtbase + SZ_4K - 0x20 + 4 * i)
& 255) << (i * 8);
for (cid = 0, i = 0; i < 4; i++)
- cid |= (readl(virtbase + resource_size(res) - 0x10 + 4 * i)
+ cid |= (readl(virtbase + SZ_4K - 0x10 + 4 * i)
& 255) << (i * 8);
if (cid != AMBA_CID) {
d40_err(dev, "Unknown hardware! No PrimeCell ID\n");
- goto unmap_io;
+ return NULL;
}
if (AMBA_MANF_BITS(pid) != AMBA_VENDOR_ST) {
d40_err(dev, "Unknown designer! Got %x wanted %x\n",
AMBA_MANF_BITS(pid),
AMBA_VENDOR_ST);
- goto unmap_io;
+ return NULL;
}
/*
* HW revision:
@@ -3200,7 +3189,7 @@ static struct d40_base * __init d40_hw_detect_init(struct platform_device *pdev)
rev = AMBA_REV_BITS(pid);
if (rev < 2) {
d40_err(dev, "hardware revision: %d is not supported", rev);
- goto unmap_io;
+ return NULL;
}
/* The number of physical channels on this HW */
@@ -3218,23 +3207,22 @@ static struct d40_base * __init d40_hw_detect_init(struct platform_device *pdev)
num_log_chans = num_phy_chans * D40_MAX_LOG_CHAN_PER_PHY;
dev_info(dev,
- "hardware rev: %d @ %pa with %d physical and %d logical channels\n",
- rev, &res->start, num_phy_chans, num_log_chans);
+ "hardware rev: %d with %d physical and %d logical channels\n",
+ rev, num_phy_chans, num_log_chans);
- base = kzalloc(ALIGN(sizeof(struct d40_base), 4) +
- (num_phy_chans + num_log_chans + num_memcpy_chans) *
- sizeof(struct d40_chan), GFP_KERNEL);
+ base = devm_kzalloc(dev,
+ ALIGN(sizeof(struct d40_base), 4) +
+ (num_phy_chans + num_log_chans + num_memcpy_chans) *
+ sizeof(struct d40_chan), GFP_KERNEL);
- if (base == NULL)
- goto unmap_io;
+ if (!base)
+ return NULL;
base->rev = rev;
base->clk = clk;
base->num_memcpy_chans = num_memcpy_chans;
base->num_phy_chans = num_phy_chans;
base->num_log_chans = num_log_chans;
- base->phy_start = res->start;
- base->phy_size = resource_size(res);
base->virtbase = virtbase;
base->plat_data = plat_data;
base->dev = dev;
@@ -3271,76 +3259,55 @@ static struct d40_base * __init d40_hw_detect_init(struct platform_device *pdev)
base->gen_dmac.init_reg_size = ARRAY_SIZE(dma_init_reg_v4a);
}
- base->phy_res = kcalloc(num_phy_chans,
- sizeof(*base->phy_res),
- GFP_KERNEL);
+ base->phy_res = devm_kcalloc(dev, num_phy_chans,
+ sizeof(*base->phy_res),
+ GFP_KERNEL);
if (!base->phy_res)
- goto free_base;
+ return NULL;
- base->lookup_phy_chans = kcalloc(num_phy_chans,
- sizeof(*base->lookup_phy_chans),
- GFP_KERNEL);
+ base->lookup_phy_chans = devm_kcalloc(dev, num_phy_chans,
+ sizeof(*base->lookup_phy_chans),
+ GFP_KERNEL);
if (!base->lookup_phy_chans)
- goto free_phy_res;
+ return NULL;
- base->lookup_log_chans = kcalloc(num_log_chans,
- sizeof(*base->lookup_log_chans),
- GFP_KERNEL);
+ base->lookup_log_chans = devm_kcalloc(dev, num_log_chans,
+ sizeof(*base->lookup_log_chans),
+ GFP_KERNEL);
if (!base->lookup_log_chans)
- goto free_phy_chans;
+ return NULL;
- base->reg_val_backup_chan = kmalloc_array(base->num_phy_chans,
+ base->reg_val_backup_chan = devm_kmalloc_array(dev, base->num_phy_chans,
sizeof(d40_backup_regs_chan),
GFP_KERNEL);
if (!base->reg_val_backup_chan)
- goto free_log_chans;
+ return NULL;
- base->lcla_pool.alloc_map = kcalloc(num_phy_chans
+ base->lcla_pool.alloc_map = devm_kcalloc(dev, num_phy_chans
* D40_LCLA_LINK_PER_EVENT_GRP,
sizeof(*base->lcla_pool.alloc_map),
GFP_KERNEL);
if (!base->lcla_pool.alloc_map)
- goto free_backup_chan;
+ return NULL;
- base->regs_interrupt = kmalloc_array(base->gen_dmac.il_size,
+ base->regs_interrupt = devm_kmalloc_array(dev, base->gen_dmac.il_size,
sizeof(*base->regs_interrupt),
GFP_KERNEL);
if (!base->regs_interrupt)
- goto free_map;
+ return NULL;
base->desc_slab = kmem_cache_create(D40_NAME, sizeof(struct d40_desc),
0, SLAB_HWCACHE_ALIGN,
NULL);
- if (base->desc_slab == NULL)
- goto free_regs;
+ if (!base->desc_slab)
+ return NULL;
+ ret = devm_add_action_or_reset(dev, d40_drop_kmem_cache_action,
+ base->desc_slab);
+ if (ret)
+ return NULL;
return base;
- free_regs:
- kfree(base->regs_interrupt);
- free_map:
- kfree(base->lcla_pool.alloc_map);
- free_backup_chan:
- kfree(base->reg_val_backup_chan);
- free_log_chans:
- kfree(base->lookup_log_chans);
- free_phy_chans:
- kfree(base->lookup_phy_chans);
- free_phy_res:
- kfree(base->phy_res);
- free_base:
- kfree(base);
- unmap_io:
- iounmap(virtbase);
- release_region:
- release_mem_region(res->start, resource_size(res));
- check_prepare_enabled:
- if (!clk_ret)
- disable_unprepare:
- clk_disable_unprepare(clk);
- if (!IS_ERR(clk))
- clk_put(clk);
- return NULL;
}
static void __init d40_hw_init(struct d40_base *base)
@@ -3585,11 +3552,11 @@ static int __init d40_probe(struct platform_device *pdev)
} else
writel(base->phy_lcpa, base->virtbase + D40_DREG_LCPA);
- base->lcpa_base = ioremap(base->phy_lcpa, base->lcpa_size);
+ base->lcpa_base = devm_ioremap(dev, base->phy_lcpa, base->lcpa_size);
if (!base->lcpa_base) {
ret = -ENOMEM;
d40_err(dev, "Failed to ioremap LCPA region\n");
- goto release_base;
+ goto report_failure;
}
/* If lcla has to be located in ESRAM we don't need to allocate */
if (base->plat_data->use_esram_lcla) {
@@ -3599,14 +3566,14 @@ static int __init d40_probe(struct platform_device *pdev)
ret = -ENOENT;
d40_err(dev,
"No \"lcla_esram\" memory resource\n");
- goto destroy_cache;
+ goto report_failure;
}
- base->lcla_pool.base = ioremap(res->start,
- resource_size(res));
+ base->lcla_pool.base = devm_ioremap(dev, res->start,
+ resource_size(res));
if (!base->lcla_pool.base) {
ret = -ENOMEM;
d40_err(dev, "Failed to ioremap LCLA region\n");
- goto destroy_cache;
+ goto report_failure;
}
writel(res->start, base->virtbase + D40_DREG_LCLA);
@@ -3678,16 +3645,8 @@ static int __init d40_probe(struct platform_device *pdev)
dev_info(base->dev, "initialized\n");
return 0;
- destroy_cache:
- kmem_cache_destroy(base->desc_slab);
- if (base->virtbase)
- iounmap(base->virtbase);
-
- if (base->lcla_pool.base && base->plat_data->use_esram_lcla) {
- iounmap(base->lcla_pool.base);
- base->lcla_pool.base = NULL;
- }
+ destroy_cache:
if (base->lcla_pool.dma_addr)
dma_unmap_single(base->dev, base->lcla_pool.dma_addr,
SZ_1K * base->num_phy_chans,
@@ -3699,28 +3658,11 @@ static int __init d40_probe(struct platform_device *pdev)
kfree(base->lcla_pool.base_unaligned);
- if (base->lcpa_base)
- iounmap(base->lcpa_base);
-
-release_base:
- if (base->phy_start)
- release_mem_region(base->phy_start,
- base->phy_size);
- if (base->clk) {
- clk_disable_unprepare(base->clk);
- clk_put(base->clk);
- }
-
if (base->lcpa_regulator) {
regulator_disable(base->lcpa_regulator);
regulator_put(base->lcpa_regulator);
}
- kfree(base->lcla_pool.alloc_map);
- kfree(base->lookup_log_chans);
- kfree(base->lookup_phy_chans);
- kfree(base->phy_res);
- kfree(base);
report_failure:
d40_err(dev, "probe failed\n");
return ret;
--
2.40.0
This makes the probe() and its subfunction d40_hw_detect_init()
return proper error codes.
One effect of this is that deferred probe, e.g from the clock,
will start to work, would it happen. Also it is better design.
Signed-off-by: Linus Walleij <[email protected]>
---
drivers/dma/ste_dma40.c | 46 ++++++++++++++++++++++++----------------------
1 file changed, 24 insertions(+), 22 deletions(-)
diff --git a/drivers/dma/ste_dma40.c b/drivers/dma/ste_dma40.c
index c5991009d3e4..2911017265cf 100644
--- a/drivers/dma/ste_dma40.c
+++ b/drivers/dma/ste_dma40.c
@@ -3132,7 +3132,8 @@ static void d40_drop_kmem_cache_action(void *d)
kmem_cache_destroy(desc_slab);
}
-static struct d40_base * __init d40_hw_detect_init(struct platform_device *pdev)
+static int __init d40_hw_detect_init(struct platform_device *pdev,
+ struct d40_base **retbase)
{
struct stedma40_platform_data *plat_data = dev_get_platdata(&pdev->dev);
struct device *dev = &pdev->dev;
@@ -3150,14 +3151,12 @@ static struct d40_base * __init d40_hw_detect_init(struct platform_device *pdev)
clk = devm_clk_get_enabled(dev, NULL);
if (IS_ERR(clk))
- return NULL;
+ return PTR_ERR(clk);
/* Get IO for DMAC base address */
virtbase = devm_platform_ioremap_resource_byname(pdev, "base");
- if (IS_ERR(virtbase)) {
- dev_err(dev, "No IO base defined\n");
- return NULL;
- }
+ if (IS_ERR(virtbase))
+ return PTR_ERR(virtbase);
/* This is just a regular AMBA PrimeCell ID actually */
for (pid = 0, i = 0; i < 4; i++)
@@ -3169,13 +3168,13 @@ static struct d40_base * __init d40_hw_detect_init(struct platform_device *pdev)
if (cid != AMBA_CID) {
d40_err(dev, "Unknown hardware! No PrimeCell ID\n");
- return NULL;
+ return -EINVAL;
}
if (AMBA_MANF_BITS(pid) != AMBA_VENDOR_ST) {
d40_err(dev, "Unknown designer! Got %x wanted %x\n",
AMBA_MANF_BITS(pid),
AMBA_VENDOR_ST);
- return NULL;
+ return -EINVAL;
}
/*
* HW revision:
@@ -3189,7 +3188,7 @@ static struct d40_base * __init d40_hw_detect_init(struct platform_device *pdev)
rev = AMBA_REV_BITS(pid);
if (rev < 2) {
d40_err(dev, "hardware revision: %d is not supported", rev);
- return NULL;
+ return -EINVAL;
}
/* The number of physical channels on this HW */
@@ -3216,7 +3215,7 @@ static struct d40_base * __init d40_hw_detect_init(struct platform_device *pdev)
sizeof(struct d40_chan), GFP_KERNEL);
if (!base)
- return NULL;
+ return -ENOMEM;
base->rev = rev;
base->clk = clk;
@@ -3263,51 +3262,53 @@ static struct d40_base * __init d40_hw_detect_init(struct platform_device *pdev)
sizeof(*base->phy_res),
GFP_KERNEL);
if (!base->phy_res)
- return NULL;
+ return -ENOMEM;
base->lookup_phy_chans = devm_kcalloc(dev, num_phy_chans,
sizeof(*base->lookup_phy_chans),
GFP_KERNEL);
if (!base->lookup_phy_chans)
- return NULL;
+ return -ENOMEM;
base->lookup_log_chans = devm_kcalloc(dev, num_log_chans,
sizeof(*base->lookup_log_chans),
GFP_KERNEL);
if (!base->lookup_log_chans)
- return NULL;
+ return -ENOMEM;
base->reg_val_backup_chan = devm_kmalloc_array(dev, base->num_phy_chans,
sizeof(d40_backup_regs_chan),
GFP_KERNEL);
if (!base->reg_val_backup_chan)
- return NULL;
+ return -ENOMEM;
base->lcla_pool.alloc_map = devm_kcalloc(dev, num_phy_chans
* D40_LCLA_LINK_PER_EVENT_GRP,
sizeof(*base->lcla_pool.alloc_map),
GFP_KERNEL);
if (!base->lcla_pool.alloc_map)
- return NULL;
+ return -ENOMEM;
base->regs_interrupt = devm_kmalloc_array(dev, base->gen_dmac.il_size,
sizeof(*base->regs_interrupt),
GFP_KERNEL);
if (!base->regs_interrupt)
- return NULL;
+ return -ENOMEM;
base->desc_slab = kmem_cache_create(D40_NAME, sizeof(struct d40_desc),
0, SLAB_HWCACHE_ALIGN,
NULL);
if (!base->desc_slab)
- return NULL;
+ return -ENOMEM;
ret = devm_add_action_or_reset(dev, d40_drop_kmem_cache_action,
base->desc_slab);
if (ret)
- return NULL;
+ return ret;
+
+ *retbase = base;
- return base;
+ return 0;
}
static void __init d40_hw_init(struct d40_base *base)
@@ -3503,20 +3504,20 @@ static int __init d40_probe(struct platform_device *pdev)
struct device *dev = &pdev->dev;
struct device_node *np = pdev->dev.of_node;
struct device_node *np_lcpa;
- int ret = -ENOENT;
struct d40_base *base;
struct resource *res;
struct resource res_lcpa;
int num_reserved_chans;
u32 val;
+ int ret;
if (d40_of_probe(dev, np)) {
ret = -ENOMEM;
goto report_failure;
}
- base = d40_hw_detect_init(pdev);
- if (!base)
+ ret = d40_hw_detect_init(pdev, &base);
+ if (ret)
goto report_failure;
num_reserved_chans = d40_phy_res_init(base);
@@ -3530,6 +3531,7 @@ static int __init d40_probe(struct platform_device *pdev)
np_lcpa = of_parse_phandle(np, "sram", 0);
if (!np_lcpa) {
dev_err(dev, "no LCPA SRAM node\n");
+ ret = -EINVAL;
goto report_failure;
}
/* This is no device so read the address directly from the node */
--
2.40.0
The U8500 has 640 KB of eSRAM, split into 5 banks of 128 KB
each. Add this to the device tree, with ESRAM 0, 1+2 and 3+4
as separate devices, since these have different power domains.
Signed-off-by: Linus Walleij <[email protected]>
---
arch/arm/boot/dts/ste-dbx5x0.dtsi | 73 +++++++++++++++++++++++++++++++++++++--
1 file changed, 71 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/ste-dbx5x0.dtsi b/arch/arm/boot/dts/ste-dbx5x0.dtsi
index fead7afd5517..c34ccde04600 100644
--- a/arch/arm/boot/dts/ste-dbx5x0.dtsi
+++ b/arch/arm/boot/dts/ste-dbx5x0.dtsi
@@ -110,6 +110,74 @@ soc {
interrupt-parent = <&intc>;
ranges;
+ /*
+ * 640KB ESRAM (embedded static random access memory), divided
+ * into 5 banks of 128 KB each. This is a fast memory usually
+ * used by different accelerators. We group these according to
+ * their power domains: ESRAM0 (always on) ESRAM 1+2 and
+ * ESRAM 3+4.
+ */
+ sram@40000000 {
+ /* The first (always on) ESRAM 0, 128 KB */
+ compatible = "mmio-sram";
+ reg = <0x40000000 0x20000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x40000000 0x20000>;
+
+ sram@0 {
+ compatible = "stericsson,u8500-esram";
+ reg = <0x0 0x10000>;
+ pool;
+ };
+ lcpa: sram@10000 {
+ /*
+ * This eSRAM is used by the DMA40 DMA controller
+ * for Logical Channel Paramers (LCP), the address
+ * where these parameters are stored is called "LCPA".
+ * This is addressed directly by the driver so no
+ * pool is used.
+ */
+ compatible = "stericsson,u8500-esram";
+ label = "DMA40-LCPA";
+ reg = <0x10000 0x800>;
+ };
+ sram@10800 {
+ compatible = "stericsson,u8500-esram";
+ reg = <0x10800 0xf800>;
+ pool;
+ };
+ };
+ sram@40020000 {
+ /* ESRAM 1+2, 256 KB */
+ compatible = "mmio-sram";
+ reg = <0x40020000 0x40000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x40020000 0x40000>;
+ };
+ sram@40060000 {
+ /* ESRAM 3+4, 256 KB */
+ compatible = "mmio-sram";
+ reg = <0x40060000 0x40000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x40060000 0x40000>;
+
+ lcla: sram@20000 {
+ /*
+ * This eSRAM is used by the DMA40 DMA controller
+ * for Logical Channel Logical Addresses (LCLA), the address
+ * where these parameters are stored is called "LCLA".
+ * This is addressed directly by the driver so no
+ * pool is used.
+ */
+ compatible = "stericsson,u8500-esram";
+ label = "DMA40-LCLA";
+ reg = <0x20000 0x2000>;
+ };
+ };
+
ptm@801ae000 {
compatible = "arm,coresight-etm3x", "arm,primecell";
reg = <0x801ae000 0x1000>;
@@ -536,9 +604,10 @@ usb_per5@a03e0000 {
dma: dma-controller@801C0000 {
compatible = "stericsson,db8500-dma40", "stericsson,dma40";
- reg = <0x801C0000 0x1000 0x40010000 0x800>;
- reg-names = "base", "lcpa";
+ reg = <0x801C0000 0x1000>;
+ reg-names = "base";
interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ sram = <&lcpa>, <&lcla>;
#dma-cells = <3>;
memcpy-channels = <56 57 58 59 60>;
--
2.40.0
The &pdev->dev device pointer is used so many times in the
probe() and d40_hw_detect_init() functions that a local *dev
variable makes the code way easier to read.
Signed-off-by: Linus Walleij <[email protected]>
---
drivers/dma/ste_dma40.c | 50 +++++++++++++++++++++++++------------------------
1 file changed, 26 insertions(+), 24 deletions(-)
diff --git a/drivers/dma/ste_dma40.c b/drivers/dma/ste_dma40.c
index 236269d35a53..ef2a2fdaa82e 100644
--- a/drivers/dma/ste_dma40.c
+++ b/drivers/dma/ste_dma40.c
@@ -3104,6 +3104,7 @@ static int __init d40_phy_res_init(struct d40_base *base)
static struct d40_base * __init d40_hw_detect_init(struct platform_device *pdev)
{
struct stedma40_platform_data *plat_data = dev_get_platdata(&pdev->dev);
+ struct device *dev = &pdev->dev;
struct clk *clk;
void __iomem *virtbase;
struct resource *res;
@@ -3117,15 +3118,15 @@ static struct d40_base * __init d40_hw_detect_init(struct platform_device *pdev)
u32 cid;
u8 rev;
- clk = clk_get(&pdev->dev, NULL);
+ clk = clk_get(dev, NULL);
if (IS_ERR(clk)) {
- d40_err(&pdev->dev, "No matching clock found\n");
+ d40_err(dev, "No matching clock found\n");
goto check_prepare_enabled;
}
clk_ret = clk_prepare_enable(clk);
if (clk_ret) {
- d40_err(&pdev->dev, "Failed to prepare/enable clock\n");
+ d40_err(dev, "Failed to prepare/enable clock\n");
goto disable_unprepare;
}
@@ -3151,11 +3152,11 @@ static struct d40_base * __init d40_hw_detect_init(struct platform_device *pdev)
& 255) << (i * 8);
if (cid != AMBA_CID) {
- d40_err(&pdev->dev, "Unknown hardware! No PrimeCell ID\n");
+ d40_err(dev, "Unknown hardware! No PrimeCell ID\n");
goto unmap_io;
}
if (AMBA_MANF_BITS(pid) != AMBA_VENDOR_ST) {
- d40_err(&pdev->dev, "Unknown designer! Got %x wanted %x\n",
+ d40_err(dev, "Unknown designer! Got %x wanted %x\n",
AMBA_MANF_BITS(pid),
AMBA_VENDOR_ST);
goto unmap_io;
@@ -3171,7 +3172,7 @@ static struct d40_base * __init d40_hw_detect_init(struct platform_device *pdev)
*/
rev = AMBA_REV_BITS(pid);
if (rev < 2) {
- d40_err(&pdev->dev, "hardware revision: %d is not supported", rev);
+ d40_err(dev, "hardware revision: %d is not supported", rev);
goto unmap_io;
}
@@ -3189,7 +3190,7 @@ static struct d40_base * __init d40_hw_detect_init(struct platform_device *pdev)
num_log_chans = num_phy_chans * D40_MAX_LOG_CHAN_PER_PHY;
- dev_info(&pdev->dev,
+ dev_info(dev,
"hardware rev: %d @ %pa with %d physical and %d logical channels\n",
rev, &res->start, num_phy_chans, num_log_chans);
@@ -3209,7 +3210,7 @@ static struct d40_base * __init d40_hw_detect_init(struct platform_device *pdev)
base->phy_size = resource_size(res);
base->virtbase = virtbase;
base->plat_data = plat_data;
- base->dev = &pdev->dev;
+ base->dev = dev;
base->phy_chans = ((void *)base) + ALIGN(sizeof(struct d40_base), 4);
base->log_chans = &base->phy_chans[num_phy_chans];
@@ -3505,7 +3506,8 @@ static int __init d40_of_probe(struct platform_device *pdev,
static int __init d40_probe(struct platform_device *pdev)
{
- struct stedma40_platform_data *plat_data = dev_get_platdata(&pdev->dev);
+ struct device *dev = &pdev->dev;
+ struct stedma40_platform_data *plat_data = dev_get_platdata(dev);
struct device_node *np = pdev->dev.of_node;
struct device_node *np_lcpa;
int ret = -ENOENT;
@@ -3522,7 +3524,7 @@ static int __init d40_probe(struct platform_device *pdev)
goto report_failure;
}
} else {
- d40_err(&pdev->dev, "No pdata or Device Tree provided\n");
+ d40_err(dev, "No pdata or Device Tree provided\n");
goto report_failure;
}
}
@@ -3541,24 +3543,24 @@ static int __init d40_probe(struct platform_device *pdev)
/* Get IO for logical channel parameter address (LCPA) */
np_lcpa = of_parse_phandle(np, "sram", 0);
if (!np_lcpa) {
- dev_err(&pdev->dev, "no LCPA SRAM node\n");
+ dev_err(dev, "no LCPA SRAM node\n");
goto report_failure;
}
/* This is no device so read the address directly from the node */
ret = of_address_to_resource(np_lcpa, 0, &res_lcpa);
if (ret) {
- dev_err(&pdev->dev, "no LCPA SRAM resource\n");
+ dev_err(dev, "no LCPA SRAM resource\n");
goto report_failure;
}
base->lcpa_size = resource_size(&res_lcpa);
base->phy_lcpa = res_lcpa.start;
- dev_info(&pdev->dev, "found LCPA SRAM at 0x%08x, size 0x%08x\n",
+ dev_info(dev, "found LCPA SRAM at 0x%08x, size 0x%08x\n",
base->phy_lcpa, base->lcpa_size);
/* We make use of ESRAM memory for this. */
val = readl(base->virtbase + D40_DREG_LCPA);
if (base->phy_lcpa != val && val != 0) {
- dev_warn(&pdev->dev,
+ dev_warn(dev,
"[%s] Mismatch LCPA dma 0x%x, def %08x\n",
__func__, val, base->phy_lcpa);
} else
@@ -3567,7 +3569,7 @@ static int __init d40_probe(struct platform_device *pdev)
base->lcpa_base = ioremap(base->phy_lcpa, base->lcpa_size);
if (!base->lcpa_base) {
ret = -ENOMEM;
- d40_err(&pdev->dev, "Failed to ioremap LCPA region\n");
+ d40_err(dev, "Failed to ioremap LCPA region\n");
goto release_base;
}
/* If lcla has to be located in ESRAM we don't need to allocate */
@@ -3576,7 +3578,7 @@ static int __init d40_probe(struct platform_device *pdev)
"lcla_esram");
if (!res) {
ret = -ENOENT;
- d40_err(&pdev->dev,
+ d40_err(dev,
"No \"lcla_esram\" memory resource\n");
goto destroy_cache;
}
@@ -3584,7 +3586,7 @@ static int __init d40_probe(struct platform_device *pdev)
resource_size(res));
if (!base->lcla_pool.base) {
ret = -ENOMEM;
- d40_err(&pdev->dev, "Failed to ioremap LCLA region\n");
+ d40_err(dev, "Failed to ioremap LCLA region\n");
goto destroy_cache;
}
writel(res->start, base->virtbase + D40_DREG_LCLA);
@@ -3592,7 +3594,7 @@ static int __init d40_probe(struct platform_device *pdev)
} else {
ret = d40_lcla_allocate(base);
if (ret) {
- d40_err(&pdev->dev, "Failed to allocate LCLA area\n");
+ d40_err(dev, "Failed to allocate LCLA area\n");
goto destroy_cache;
}
}
@@ -3603,7 +3605,7 @@ static int __init d40_probe(struct platform_device *pdev)
ret = request_irq(base->irq, d40_handle_interrupt, 0, D40_NAME, base);
if (ret) {
- d40_err(&pdev->dev, "No IRQ defined\n");
+ d40_err(dev, "No IRQ defined\n");
goto destroy_cache;
}
@@ -3611,7 +3613,7 @@ static int __init d40_probe(struct platform_device *pdev)
base->lcpa_regulator = regulator_get(base->dev, "lcla_esram");
if (IS_ERR(base->lcpa_regulator)) {
- d40_err(&pdev->dev, "Failed to get lcpa_regulator\n");
+ d40_err(dev, "Failed to get lcpa_regulator\n");
ret = PTR_ERR(base->lcpa_regulator);
base->lcpa_regulator = NULL;
goto destroy_cache;
@@ -3619,7 +3621,7 @@ static int __init d40_probe(struct platform_device *pdev)
ret = regulator_enable(base->lcpa_regulator);
if (ret) {
- d40_err(&pdev->dev,
+ d40_err(dev,
"Failed to enable lcpa_regulator\n");
regulator_put(base->lcpa_regulator);
base->lcpa_regulator = NULL;
@@ -3642,7 +3644,7 @@ static int __init d40_probe(struct platform_device *pdev)
ret = dma_set_max_seg_size(base->dev, STEDMA40_MAX_SEG_SIZE);
if (ret) {
- d40_err(&pdev->dev, "Failed to set dma max seg size\n");
+ d40_err(dev, "Failed to set dma max seg size\n");
goto destroy_cache;
}
@@ -3651,7 +3653,7 @@ static int __init d40_probe(struct platform_device *pdev)
if (np) {
ret = of_dma_controller_register(np, d40_xlate, NULL);
if (ret)
- dev_err(&pdev->dev,
+ dev_err(dev,
"could not register of_dma_controller\n");
}
@@ -3701,7 +3703,7 @@ static int __init d40_probe(struct platform_device *pdev)
kfree(base->phy_res);
kfree(base);
report_failure:
- d40_err(&pdev->dev, "probe failed\n");
+ d40_err(dev, "probe failed\n");
return ret;
}
--
2.40.0
The Ux500 is device tree-only since ages. Delete the
platform data header and push it into or next to the driver
instead.
Drop the non-DT probe path since this will not happen.
Signed-off-by: Linus Walleij <[email protected]>
---
drivers/dma/ste_dma40.c | 56 ++++++++----
.../dma-ste-dma40.h => drivers/dma/ste_dma40.h | 101 +--------------------
drivers/dma/ste_dma40_ll.c | 3 +-
3 files changed, 41 insertions(+), 119 deletions(-)
diff --git a/drivers/dma/ste_dma40.c b/drivers/dma/ste_dma40.c
index ef2a2fdaa82e..e5df28cdc4c8 100644
--- a/drivers/dma/ste_dma40.c
+++ b/drivers/dma/ste_dma40.c
@@ -23,11 +23,39 @@
#include <linux/of_dma.h>
#include <linux/amba/bus.h>
#include <linux/regulator/consumer.h>
-#include <linux/platform_data/dma-ste-dma40.h>
#include "dmaengine.h"
+#include "ste_dma40.h"
#include "ste_dma40_ll.h"
+/**
+ * struct stedma40_platform_data - Configuration struct for the dma device.
+ *
+ * @dev_tx: mapping between destination event line and io address
+ * @dev_rx: mapping between source event line and io address
+ * @disabled_channels: A vector, ending with -1, that marks physical channels
+ * that are for different reasons not available for the driver.
+ * @soft_lli_chans: A vector, that marks physical channels will use LLI by SW
+ * which avoids HW bug that exists in some versions of the controller.
+ * SoftLLI introduces relink overhead that could impact performace for
+ * certain use cases.
+ * @num_of_soft_lli_chans: The number of channels that needs to be configured
+ * to use SoftLLI.
+ * @use_esram_lcla: flag for mapping the lcla into esram region
+ * @num_of_memcpy_chans: The number of channels reserved for memcpy.
+ * @num_of_phy_chans: The number of physical channels implemented in HW.
+ * 0 means reading the number of channels from DMA HW but this is only valid
+ * for 'multiple of 4' channels, like 8.
+ */
+struct stedma40_platform_data {
+ int disabled_channels[STEDMA40_MAX_PHYS];
+ int *soft_lli_chans;
+ int num_of_soft_lli_chans;
+ bool use_esram_lcla;
+ int num_of_memcpy_chans;
+ int num_of_phy_chans;
+};
+
#define D40_NAME "dma40"
#define D40_PHY_CHAN -1
@@ -2269,7 +2297,7 @@ d40_prep_sg(struct dma_chan *dchan, struct scatterlist *sg_src,
return NULL;
}
-bool stedma40_filter(struct dma_chan *chan, void *data)
+static bool stedma40_filter(struct dma_chan *chan, void *data)
{
struct stedma40_chan_cfg *info = data;
struct d40_chan *d40c =
@@ -2288,7 +2316,6 @@ bool stedma40_filter(struct dma_chan *chan, void *data)
return err == 0;
}
-EXPORT_SYMBOL(stedma40_filter);
static void __d40_set_prio_rt(struct d40_chan *d40c, int dev_type, bool src)
{
@@ -3517,16 +3544,9 @@ static int __init d40_probe(struct platform_device *pdev)
int num_reserved_chans;
u32 val;
- if (!plat_data) {
- if (np) {
- if (d40_of_probe(pdev, np)) {
- ret = -ENOMEM;
- goto report_failure;
- }
- } else {
- d40_err(dev, "No pdata or Device Tree provided\n");
- goto report_failure;
- }
+ if (d40_of_probe(pdev, np)) {
+ ret = -ENOMEM;
+ goto report_failure;
}
base = d40_hw_detect_init(pdev);
@@ -3650,11 +3670,11 @@ static int __init d40_probe(struct platform_device *pdev)
d40_hw_init(base);
- if (np) {
- ret = of_dma_controller_register(np, d40_xlate, NULL);
- if (ret)
- dev_err(dev,
- "could not register of_dma_controller\n");
+ ret = of_dma_controller_register(np, d40_xlate, NULL);
+ if (ret) {
+ dev_err(dev,
+ "could not register of_dma_controller\n");
+ goto destroy_cache;
}
dev_info(base->dev, "initialized\n");
diff --git a/include/linux/platform_data/dma-ste-dma40.h b/drivers/dma/ste_dma40.h
similarity index 51%
rename from include/linux/platform_data/dma-ste-dma40.h
rename to drivers/dma/ste_dma40.h
index 10641633facc..c697bfe16a01 100644
--- a/include/linux/platform_data/dma-ste-dma40.h
+++ b/drivers/dma/ste_dma40.h
@@ -1,19 +1,8 @@
/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright (C) ST-Ericsson SA 2007-2010
- * Author: Per Forlin <[email protected]> for ST-Ericsson
- * Author: Jonas Aaberg <[email protected]> for ST-Ericsson
- */
-
#ifndef STE_DMA40_H
#define STE_DMA40_H
-#include <linux/dmaengine.h>
-#include <linux/scatterlist.h>
-#include <linux/workqueue.h>
-#include <linux/interrupt.h>
-
/*
* Maxium size for a single dma descriptor
* Size is limited to 16 bits.
@@ -118,92 +107,4 @@ struct stedma40_chan_cfg {
int phy_channel;
};
-/**
- * struct stedma40_platform_data - Configuration struct for the dma device.
- *
- * @dev_tx: mapping between destination event line and io address
- * @dev_rx: mapping between source event line and io address
- * @disabled_channels: A vector, ending with -1, that marks physical channels
- * that are for different reasons not available for the driver.
- * @soft_lli_chans: A vector, that marks physical channels will use LLI by SW
- * which avoids HW bug that exists in some versions of the controller.
- * SoftLLI introduces relink overhead that could impact performace for
- * certain use cases.
- * @num_of_soft_lli_chans: The number of channels that needs to be configured
- * to use SoftLLI.
- * @use_esram_lcla: flag for mapping the lcla into esram region
- * @num_of_memcpy_chans: The number of channels reserved for memcpy.
- * @num_of_phy_chans: The number of physical channels implemented in HW.
- * 0 means reading the number of channels from DMA HW but this is only valid
- * for 'multiple of 4' channels, like 8.
- */
-struct stedma40_platform_data {
- int disabled_channels[STEDMA40_MAX_PHYS];
- int *soft_lli_chans;
- int num_of_soft_lli_chans;
- bool use_esram_lcla;
- int num_of_memcpy_chans;
- int num_of_phy_chans;
-};
-
-#ifdef CONFIG_STE_DMA40
-
-/**
- * stedma40_filter() - Provides stedma40_chan_cfg to the
- * ste_dma40 dma driver via the dmaengine framework.
- * does some checking of what's provided.
- *
- * Never directly called by client. It used by dmaengine.
- * @chan: dmaengine handle.
- * @data: Must be of type: struct stedma40_chan_cfg and is
- * the configuration of the framework.
- *
- *
- */
-
-bool stedma40_filter(struct dma_chan *chan, void *data);
-
-/**
- * stedma40_slave_mem() - Transfers a raw data buffer to or from a slave
- * (=device)
- *
- * @chan: dmaengine handle
- * @addr: source or destination physicall address.
- * @size: bytes to transfer
- * @direction: direction of transfer
- * @flags: is actually enum dma_ctrl_flags. See dmaengine.h
- */
-
-static inline struct
-dma_async_tx_descriptor *stedma40_slave_mem(struct dma_chan *chan,
- dma_addr_t addr,
- unsigned int size,
- enum dma_transfer_direction direction,
- unsigned long flags)
-{
- struct scatterlist sg;
- sg_init_table(&sg, 1);
- sg.dma_address = addr;
- sg.length = size;
-
- return dmaengine_prep_slave_sg(chan, &sg, 1, direction, flags);
-}
-
-#else
-static inline bool stedma40_filter(struct dma_chan *chan, void *data)
-{
- return false;
-}
-
-static inline struct
-dma_async_tx_descriptor *stedma40_slave_mem(struct dma_chan *chan,
- dma_addr_t addr,
- unsigned int size,
- enum dma_transfer_direction direction,
- unsigned long flags)
-{
- return NULL;
-}
-#endif
-
-#endif
+#endif /* STE_DMA40_H */
diff --git a/drivers/dma/ste_dma40_ll.c b/drivers/dma/ste_dma40_ll.c
index b5287c661eb7..4c489b126cb2 100644
--- a/drivers/dma/ste_dma40_ll.c
+++ b/drivers/dma/ste_dma40_ll.c
@@ -6,8 +6,9 @@
*/
#include <linux/kernel.h>
-#include <linux/platform_data/dma-ste-dma40.h>
+#include <linux/dmaengine.h>
+#include "ste_dma40.h"
#include "ste_dma40_ll.h"
static u8 d40_width_to_bits(enum dma_slave_buswidth width)
--
2.40.0
On Thu, 27 Apr 2023 14:09:56 +0200, Linus Walleij wrote:
> Extend the DMA40 bindings so that we can pass two SRAM
> segments as phandles instead of directly referring to the
> memory address in the second reg cell. This enables more
> granular control over the SRAM, and adds the optiona LCLA
> SRAM segment as well.
>
> Deprecate the old way of passing LCPA as a second reg cell,
> make sram compulsory.
>
> Signed-off-by: Linus Walleij <[email protected]>
> ---
> ChangeLog v1->v2:
> - Enumerate phandles using inner and outer maxItems as specified
> by Rob.
> - Drop quotes around reference.
> ---
> .../devicetree/bindings/dma/stericsson,dma40.yaml | 36 +++++++++++++++++-----
> 1 file changed, 28 insertions(+), 8 deletions(-)
>
Reviewed-by: Rob Herring <[email protected]>