Add support to vote for ICC bandwidth based on the link speed and width.
This patch is inspired from pcie-qcom driver to add basic interconnect
support.
Link: https://lore.kernel.org/all/[email protected]/
Signed-off-by: Krishna chaitanya chundru <[email protected]>
---
drivers/pci/controller/dwc/pcie-qcom-ep.c | 68 +++++++++++++++++++++++++++++++
1 file changed, 68 insertions(+)
diff --git a/drivers/pci/controller/dwc/pcie-qcom-ep.c b/drivers/pci/controller/dwc/pcie-qcom-ep.c
index 19b3283..baf831f 100644
--- a/drivers/pci/controller/dwc/pcie-qcom-ep.c
+++ b/drivers/pci/controller/dwc/pcie-qcom-ep.c
@@ -13,6 +13,7 @@
#include <linux/debugfs.h>
#include <linux/delay.h>
#include <linux/gpio/consumer.h>
+#include <linux/interconnect.h>
#include <linux/mfd/syscon.h>
#include <linux/phy/pcie.h>
#include <linux/phy/phy.h>
@@ -28,6 +29,7 @@
#define PARF_SYS_CTRL 0x00
#define PARF_DB_CTRL 0x10
#define PARF_PM_CTRL 0x20
+#define PARF_PM_STTS 0x24
#define PARF_MHI_CLOCK_RESET_CTRL 0x174
#define PARF_MHI_BASE_ADDR_LOWER 0x178
#define PARF_MHI_BASE_ADDR_UPPER 0x17c
@@ -128,6 +130,9 @@
/* DBI register fields */
#define DBI_CON_STATUS_POWER_STATE_MASK GENMASK(1, 0)
+#define DBI_LINKCTRLSTATUS 0x80
+#define DBI_LINKCTRLSTATUS_SHIFT 16
+
#define XMLH_LINK_UP 0x400
#define CORE_RESET_TIME_US_MIN 1000
#define CORE_RESET_TIME_US_MAX 1005
@@ -178,6 +183,8 @@ struct qcom_pcie_ep {
struct phy *phy;
struct dentry *debugfs;
+ struct icc_path *icc_mem;
+
struct clk_bulk_data *clks;
int num_clks;
@@ -253,9 +260,51 @@ static void qcom_pcie_dw_stop_link(struct dw_pcie *pci)
disable_irq(pcie_ep->perst_irq);
}
+static void qcom_pcie_ep_icc_update(struct qcom_pcie_ep *pcie_ep)
+{
+ struct dw_pcie *pci = &pcie_ep->pci;
+ u32 offset, status, bw;
+ int speed, width;
+ int ret;
+
+ if (!pcie_ep->icc_mem)
+ return;
+
+ offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
+ status = readw(pci->dbi_base + offset + PCI_EXP_LNKSTA);
+
+ speed = FIELD_GET(PCI_EXP_LNKSTA_CLS, status);
+ width = FIELD_GET(PCI_EXP_LNKSTA_NLW, status);
+
+ switch (speed) {
+ case 1:
+ bw = MBps_to_icc(250); /* BW for GEN1 per lane: 250MBps */
+ break;
+ case 2:
+ bw = MBps_to_icc(500); /* BW for GEN2 per lane: 500MBps */
+ break;
+ case 3:
+ bw = MBps_to_icc(985); /* BW for GEN3 per lane: 985MBps */
+ break;
+ default:
+ WARN_ON_ONCE(1);
+ fallthrough;
+ case 4:
+ bw = MBps_to_icc(1969); /* BW for GEN4 per lane:1969MBps */
+ break;
+ }
+
+ ret = icc_set_bw(pcie_ep->icc_mem, 0, width * bw);
+ if (ret) {
+ dev_err(pci->dev, "failed to set interconnect bandwidth: %d\n",
+ ret);
+ }
+}
+
static int qcom_pcie_enable_resources(struct qcom_pcie_ep *pcie_ep)
{
int ret;
+ struct dw_pcie *pci = &pcie_ep->pci;
ret = clk_bulk_prepare_enable(pcie_ep->num_clks, pcie_ep->clks);
if (ret)
@@ -277,6 +326,20 @@ static int qcom_pcie_enable_resources(struct qcom_pcie_ep *pcie_ep)
if (ret)
goto err_phy_exit;
+ /*
+ * Some Qualcomm platforms require interconnect bandwidth constraints
+ * to be set before enabling interconnect clocks.
+ *
+ * Set an initial average bandwidth corresponding to GEN1x1(250 MBps)
+ * for the pcie to mem path.
+ */
+ ret = icc_set_bw(pcie_ep->icc_mem, 0, MBps_to_icc(250));
+ if (ret) {
+ dev_err(pci->dev, "failed to set interconnect bandwidth: %d\n",
+ ret);
+ goto err_phy_exit;
+ }
+
return 0;
err_phy_exit:
@@ -550,6 +613,10 @@ static int qcom_pcie_ep_get_resources(struct platform_device *pdev,
if (IS_ERR(pcie_ep->phy))
ret = PTR_ERR(pcie_ep->phy);
+ pcie_ep->icc_mem = devm_of_icc_get(dev, "pcie-mem");
+ if (IS_ERR(pcie_ep->icc_mem))
+ ret = PTR_ERR(pcie_ep->icc_mem);
+
return ret;
}
@@ -572,6 +639,7 @@ static irqreturn_t qcom_pcie_ep_global_irq_thread(int irq, void *data)
} else if (FIELD_GET(PARF_INT_ALL_BME, status)) {
dev_dbg(dev, "Received BME event. Link is enabled!\n");
pcie_ep->link_status = QCOM_PCIE_EP_LINK_ENABLED;
+ qcom_pcie_ep_icc_update(pcie_ep);
} else if (FIELD_GET(PARF_INT_ALL_PM_TURNOFF, status)) {
dev_dbg(dev, "Received PM Turn-off event! Entering L23\n");
val = readl_relaxed(pcie_ep->parf + PARF_PM_CTRL);
--
2.7.4
On Fri, 9 Jun 2023 at 14:47, Krishna chaitanya chundru
<[email protected]> wrote:
>
> Add support to vote for ICC bandwidth based on the link speed and width.
>
> This patch is inspired from pcie-qcom driver to add basic interconnect
> support.
>
> Link: https://lore.kernel.org/all/[email protected]/
This link should be a part of the cover letter, not the commit msg. If
you want to refer to the previous commits, please use the standard
reference: commit abcdefabc ("PCI: qcom: Make foo and bar").
> Signed-off-by: Krishna chaitanya chundru <[email protected]>
> ---
> drivers/pci/controller/dwc/pcie-qcom-ep.c | 68 +++++++++++++++++++++++++++++++
> 1 file changed, 68 insertions(+)
>
> diff --git a/drivers/pci/controller/dwc/pcie-qcom-ep.c b/drivers/pci/controller/dwc/pcie-qcom-ep.c
> index 19b3283..baf831f 100644
> --- a/drivers/pci/controller/dwc/pcie-qcom-ep.c
> +++ b/drivers/pci/controller/dwc/pcie-qcom-ep.c
> @@ -13,6 +13,7 @@
> #include <linux/debugfs.h>
> #include <linux/delay.h>
> #include <linux/gpio/consumer.h>
> +#include <linux/interconnect.h>
> #include <linux/mfd/syscon.h>
> #include <linux/phy/pcie.h>
> #include <linux/phy/phy.h>
> @@ -28,6 +29,7 @@
> #define PARF_SYS_CTRL 0x00
> #define PARF_DB_CTRL 0x10
> #define PARF_PM_CTRL 0x20
> +#define PARF_PM_STTS 0x24
> #define PARF_MHI_CLOCK_RESET_CTRL 0x174
> #define PARF_MHI_BASE_ADDR_LOWER 0x178
> #define PARF_MHI_BASE_ADDR_UPPER 0x17c
> @@ -128,6 +130,9 @@
> /* DBI register fields */
> #define DBI_CON_STATUS_POWER_STATE_MASK GENMASK(1, 0)
>
> +#define DBI_LINKCTRLSTATUS 0x80
> +#define DBI_LINKCTRLSTATUS_SHIFT 16
> +
> #define XMLH_LINK_UP 0x400
> #define CORE_RESET_TIME_US_MIN 1000
> #define CORE_RESET_TIME_US_MAX 1005
> @@ -178,6 +183,8 @@ struct qcom_pcie_ep {
> struct phy *phy;
> struct dentry *debugfs;
>
> + struct icc_path *icc_mem;
> +
> struct clk_bulk_data *clks;
> int num_clks;
>
> @@ -253,9 +260,51 @@ static void qcom_pcie_dw_stop_link(struct dw_pcie *pci)
> disable_irq(pcie_ep->perst_irq);
> }
>
> +static void qcom_pcie_ep_icc_update(struct qcom_pcie_ep *pcie_ep)
> +{
> + struct dw_pcie *pci = &pcie_ep->pci;
> + u32 offset, status, bw;
> + int speed, width;
> + int ret;
> +
> + if (!pcie_ep->icc_mem)
> + return;
> +
> + offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
> + status = readw(pci->dbi_base + offset + PCI_EXP_LNKSTA);
> +
> + speed = FIELD_GET(PCI_EXP_LNKSTA_CLS, status);
> + width = FIELD_GET(PCI_EXP_LNKSTA_NLW, status);
> +
> + switch (speed) {
> + case 1:
> + bw = MBps_to_icc(250); /* BW for GEN1 per lane: 250MBps */
Please extract these constants to the defines. This would save you
from duplicating 250 below.
> + break;
> + case 2:
> + bw = MBps_to_icc(500); /* BW for GEN2 per lane: 500MBps */
> + break;
> + case 3:
> + bw = MBps_to_icc(985); /* BW for GEN3 per lane: 985MBps */
> + break;
> + default:
> + WARN_ON_ONCE(1);
> + fallthrough;
> + case 4:
> + bw = MBps_to_icc(1969); /* BW for GEN4 per lane:1969MBps */
> + break;
> + }
> +
> + ret = icc_set_bw(pcie_ep->icc_mem, 0, width * bw);
> + if (ret) {
> + dev_err(pci->dev, "failed to set interconnect bandwidth: %d\n",
> + ret);
> + }
> +}
> +
> static int qcom_pcie_enable_resources(struct qcom_pcie_ep *pcie_ep)
> {
> int ret;
> + struct dw_pcie *pci = &pcie_ep->pci;
>
> ret = clk_bulk_prepare_enable(pcie_ep->num_clks, pcie_ep->clks);
> if (ret)
> @@ -277,6 +326,20 @@ static int qcom_pcie_enable_resources(struct qcom_pcie_ep *pcie_ep)
> if (ret)
> goto err_phy_exit;
>
> + /*
> + * Some Qualcomm platforms require interconnect bandwidth constraints
> + * to be set before enabling interconnect clocks.
> + *
> + * Set an initial average bandwidth corresponding to GEN1x1(250 MBps)
> + * for the pcie to mem path.
> + */
> + ret = icc_set_bw(pcie_ep->icc_mem, 0, MBps_to_icc(250));
> + if (ret) {
> + dev_err(pci->dev, "failed to set interconnect bandwidth: %d\n",
> + ret);
> + goto err_phy_exit;
> + }
> +
> return 0;
>
> err_phy_exit:
> @@ -550,6 +613,10 @@ static int qcom_pcie_ep_get_resources(struct platform_device *pdev,
> if (IS_ERR(pcie_ep->phy))
> ret = PTR_ERR(pcie_ep->phy);
>
> + pcie_ep->icc_mem = devm_of_icc_get(dev, "pcie-mem");
> + if (IS_ERR(pcie_ep->icc_mem))
> + ret = PTR_ERR(pcie_ep->icc_mem);
> +
> return ret;
> }
>
> @@ -572,6 +639,7 @@ static irqreturn_t qcom_pcie_ep_global_irq_thread(int irq, void *data)
> } else if (FIELD_GET(PARF_INT_ALL_BME, status)) {
> dev_dbg(dev, "Received BME event. Link is enabled!\n");
> pcie_ep->link_status = QCOM_PCIE_EP_LINK_ENABLED;
> + qcom_pcie_ep_icc_update(pcie_ep);
> } else if (FIELD_GET(PARF_INT_ALL_PM_TURNOFF, status)) {
> dev_dbg(dev, "Received PM Turn-off event! Entering L23\n");
> val = readl_relaxed(pcie_ep->parf + PARF_PM_CTRL);
> --
> 2.7.4
>
--
With best wishes
Dmitry
On 6/9/2023 9:56 PM, Dmitry Baryshkov wrote:
> On Fri, 9 Jun 2023 at 14:47, Krishna chaitanya chundru
> <[email protected]> wrote:
>> Add support to vote for ICC bandwidth based on the link speed and width.
>>
>> This patch is inspired from pcie-qcom driver to add basic interconnect
>> support.
>>
>> Link: https://lore.kernel.org/all/[email protected]/
> This link should be a part of the cover letter, not the commit msg. If
> you want to refer to the previous commits, please use the standard
> reference: commit abcdefabc ("PCI: qcom: Make foo and bar").
done
>> Signed-off-by: Krishna chaitanya chundru <[email protected]>
>> ---
>> drivers/pci/controller/dwc/pcie-qcom-ep.c | 68 +++++++++++++++++++++++++++++++
>> 1 file changed, 68 insertions(+)
>>
>> diff --git a/drivers/pci/controller/dwc/pcie-qcom-ep.c b/drivers/pci/controller/dwc/pcie-qcom-ep.c
>> index 19b3283..baf831f 100644
>> --- a/drivers/pci/controller/dwc/pcie-qcom-ep.c
>> +++ b/drivers/pci/controller/dwc/pcie-qcom-ep.c
>> @@ -13,6 +13,7 @@
>> #include <linux/debugfs.h>
>> #include <linux/delay.h>
>> #include <linux/gpio/consumer.h>
>> +#include <linux/interconnect.h>
>> #include <linux/mfd/syscon.h>
>> #include <linux/phy/pcie.h>
>> #include <linux/phy/phy.h>
>> @@ -28,6 +29,7 @@
>> #define PARF_SYS_CTRL 0x00
>> #define PARF_DB_CTRL 0x10
>> #define PARF_PM_CTRL 0x20
>> +#define PARF_PM_STTS 0x24
>> #define PARF_MHI_CLOCK_RESET_CTRL 0x174
>> #define PARF_MHI_BASE_ADDR_LOWER 0x178
>> #define PARF_MHI_BASE_ADDR_UPPER 0x17c
>> @@ -128,6 +130,9 @@
>> /* DBI register fields */
>> #define DBI_CON_STATUS_POWER_STATE_MASK GENMASK(1, 0)
>>
>> +#define DBI_LINKCTRLSTATUS 0x80
>> +#define DBI_LINKCTRLSTATUS_SHIFT 16
>> +
>> #define XMLH_LINK_UP 0x400
>> #define CORE_RESET_TIME_US_MIN 1000
>> #define CORE_RESET_TIME_US_MAX 1005
>> @@ -178,6 +183,8 @@ struct qcom_pcie_ep {
>> struct phy *phy;
>> struct dentry *debugfs;
>>
>> + struct icc_path *icc_mem;
>> +
>> struct clk_bulk_data *clks;
>> int num_clks;
>>
>> @@ -253,9 +260,51 @@ static void qcom_pcie_dw_stop_link(struct dw_pcie *pci)
>> disable_irq(pcie_ep->perst_irq);
>> }
>>
>> +static void qcom_pcie_ep_icc_update(struct qcom_pcie_ep *pcie_ep)
>> +{
>> + struct dw_pcie *pci = &pcie_ep->pci;
>> + u32 offset, status, bw;
>> + int speed, width;
>> + int ret;
>> +
>> + if (!pcie_ep->icc_mem)
>> + return;
>> +
>> + offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
>> + status = readw(pci->dbi_base + offset + PCI_EXP_LNKSTA);
>> +
>> + speed = FIELD_GET(PCI_EXP_LNKSTA_CLS, status);
>> + width = FIELD_GET(PCI_EXP_LNKSTA_NLW, status);
>> +
>> + switch (speed) {
>> + case 1:
>> + bw = MBps_to_icc(250); /* BW for GEN1 per lane: 250MBps */
> Please extract these constants to the defines. This would save you
> from duplicating 250 below.
done
>> + break;
>> + case 2:
>> + bw = MBps_to_icc(500); /* BW for GEN2 per lane: 500MBps */
>> + break;
>> + case 3:
>> + bw = MBps_to_icc(985); /* BW for GEN3 per lane: 985MBps */
>> + break;
>> + default:
>> + WARN_ON_ONCE(1);
>> + fallthrough;
>> + case 4:
>> + bw = MBps_to_icc(1969); /* BW for GEN4 per lane:1969MBps */
>> + break;
>> + }
>> +
>> + ret = icc_set_bw(pcie_ep->icc_mem, 0, width * bw);
>> + if (ret) {
>> + dev_err(pci->dev, "failed to set interconnect bandwidth: %d\n",
>> + ret);
>> + }
>> +}
>> +
>> static int qcom_pcie_enable_resources(struct qcom_pcie_ep *pcie_ep)
>> {
>> int ret;
>> + struct dw_pcie *pci = &pcie_ep->pci;
>>
>> ret = clk_bulk_prepare_enable(pcie_ep->num_clks, pcie_ep->clks);
>> if (ret)
>> @@ -277,6 +326,20 @@ static int qcom_pcie_enable_resources(struct qcom_pcie_ep *pcie_ep)
>> if (ret)
>> goto err_phy_exit;
>>
>> + /*
>> + * Some Qualcomm platforms require interconnect bandwidth constraints
>> + * to be set before enabling interconnect clocks.
>> + *
>> + * Set an initial average bandwidth corresponding to GEN1x1(250 MBps)
>> + * for the pcie to mem path.
>> + */
>> + ret = icc_set_bw(pcie_ep->icc_mem, 0, MBps_to_icc(250));
>> + if (ret) {
>> + dev_err(pci->dev, "failed to set interconnect bandwidth: %d\n",
>> + ret);
>> + goto err_phy_exit;
>> + }
>> +
>> return 0;
>>
>> err_phy_exit:
>> @@ -550,6 +613,10 @@ static int qcom_pcie_ep_get_resources(struct platform_device *pdev,
>> if (IS_ERR(pcie_ep->phy))
>> ret = PTR_ERR(pcie_ep->phy);
>>
>> + pcie_ep->icc_mem = devm_of_icc_get(dev, "pcie-mem");
>> + if (IS_ERR(pcie_ep->icc_mem))
>> + ret = PTR_ERR(pcie_ep->icc_mem);
>> +
>> return ret;
>> }
>>
>> @@ -572,6 +639,7 @@ static irqreturn_t qcom_pcie_ep_global_irq_thread(int irq, void *data)
>> } else if (FIELD_GET(PARF_INT_ALL_BME, status)) {
>> dev_dbg(dev, "Received BME event. Link is enabled!\n");
>> pcie_ep->link_status = QCOM_PCIE_EP_LINK_ENABLED;
>> + qcom_pcie_ep_icc_update(pcie_ep);
>> } else if (FIELD_GET(PARF_INT_ALL_PM_TURNOFF, status)) {
>> dev_dbg(dev, "Received PM Turn-off event! Entering L23\n");
>> val = readl_relaxed(pcie_ep->parf + PARF_PM_CTRL);
>> --
>> 2.7.4
>>
>