Normally, the maximum brightness is determined by the hardware, and this
property is not required. This property is used to set a software limit.
It could happen that an LED is made so bright that it gets damaged or
causes damage due to restrictions in a specific system, such as mounting
conditions.
Note that this flag is mainly used for PWM-LEDs, where it is not possible
to map brightness to current. Drivers for other controllers should use
led-max-microamp.
Signed-off-by: Astrid Rost <[email protected]>
---
Documentation/devicetree/bindings/leds/common.yaml | 12 ++++++++++++
1 file changed, 12 insertions(+)
diff --git a/Documentation/devicetree/bindings/leds/common.yaml b/Documentation/devicetree/bindings/leds/common.yaml
index 11aedf1650a1..16f08d0939ce 100644
--- a/Documentation/devicetree/bindings/leds/common.yaml
+++ b/Documentation/devicetree/bindings/leds/common.yaml
@@ -160,6 +160,18 @@ properties:
For flash LED controllers with configurable current this property is
mandatory for the LEDs in the non-flash modes (e.g. torch or indicator).
+ max-brightness:
+ description:
+ Normally, the maximum brightness is determined by the hardware, and this
+ property is not required. This property is used to set a software limit.
+ It could happen that an LED is made so bright that it gets damaged or
+ causes damage due to restrictions in a specific system, such as mounting
+ conditions.
+ Note that this flag is mainly used for PWM-LEDs, where it is not possible
+ to map brightness to current. Drivers for other controllers should use
+ led-max-microamp.
+ $ref: /schemas/types.yaml#definitions/uint32
+
panic-indicator:
description:
This property specifies that the LED should be used, if at all possible,
--
2.30.2
On 03/07/2023 15:03, Astrid Rost wrote:
> Normally, the maximum brightness is determined by the hardware, and this
> property is not required. This property is used to set a software limit.
> It could happen that an LED is made so bright that it gets damaged or
> causes damage due to restrictions in a specific system, such as mounting
> conditions.
> Note that this flag is mainly used for PWM-LEDs, where it is not possible
> to map brightness to current. Drivers for other controllers should use
> led-max-microamp.
>
> Signed-off-by: Astrid Rost <[email protected]>
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Best regards,
Krzysztof
On Mon, 03 Jul 2023 15:03:12 +0200, Astrid Rost wrote:
> Normally, the maximum brightness is determined by the hardware, and this
> property is not required. This property is used to set a software limit.
> It could happen that an LED is made so bright that it gets damaged or
> causes damage due to restrictions in a specific system, such as mounting
> conditions.
> Note that this flag is mainly used for PWM-LEDs, where it is not possible
> to map brightness to current. Drivers for other controllers should use
> led-max-microamp.
>
> Signed-off-by: Astrid Rost <[email protected]>
> ---
> Documentation/devicetree/bindings/leds/common.yaml | 12 ++++++++++++
> 1 file changed, 12 insertions(+)
>
Reviewed-by: Rob Herring <[email protected]>
On Mon, 03 Jul 2023, Astrid Rost wrote:
> Normally, the maximum brightness is determined by the hardware, and this
> property is not required. This property is used to set a software limit.
> It could happen that an LED is made so bright that it gets damaged or
> causes damage due to restrictions in a specific system, such as mounting
> conditions.
> Note that this flag is mainly used for PWM-LEDs, where it is not possible
> to map brightness to current. Drivers for other controllers should use
> led-max-microamp.
>
> Signed-off-by: Astrid Rost <[email protected]>
> ---
> Documentation/devicetree/bindings/leds/common.yaml | 12 ++++++++++++
> 1 file changed, 12 insertions(+)
Applied, thanks
--
Lee Jones [李琼斯]