Hi,
Changes in v2:
- Added compatible for pm7550ba for eusb2 repeater and used it in DT.
- Addressed some minor comments from Konrad to add fixes tag, labels
and update the labels
This series add support of pmics that are found in SDX75 platform and
add the corresponding regulators in the IDP platform as well.
It also parallely updates the pmic found in SDX65 to PM7250b and add pinctrl
support for the same pmic chip.
This series is based on the new header inclusion[1] and movement of the
regulators level from rpmpd to rpmhpd[2].
This series can be picked after successfully picking [2] and [3] as [1] has
already been applied.
[1] https://lore.kernel.org/all/[email protected]/
[2] https://lore.kernel.org/all/[email protected]/
[3] https://lore.kernel.org/all/[email protected]/
Thanks,
Rohit.
Rohit Agarwal (9):
dt-bindings: phy: qcom,snps-eusb2-repeater: Add compatible for
PM7550BA
arm64: dts: qcom: sdx75: Add spmi node
arm64: dts: qcom: Add pinctrl gpio support for pm7250b
arm64: dts: qcom: Add pm7550ba PMIC dtsi
arm64: dts: qcom: Add pmx75 PMIC dtsi
ARM: dts: qcom: sdx65-mtp: Update the pmic used in sdx65
arm64: dts: qcom: sdx75-idp: Add pmics supported in SDX75
arm64: dts: qcom: sdx75: Add rpmhpd node
arm64: dts: qcom: sdx75-idp: Add regulator nodes
.../bindings/phy/qcom,snps-eusb2-repeater.yaml | 7 +-
arch/arm/boot/dts/qcom/qcom-sdx65-mtp.dts | 2 +-
arch/arm64/boot/dts/qcom/pm7250b.dtsi | 10 +
arch/arm64/boot/dts/qcom/pm7550ba.dtsi | 70 +++++++
arch/arm64/boot/dts/qcom/pmx75.dtsi | 64 ++++++
arch/arm64/boot/dts/qcom/sdx75-idp.dts | 230 +++++++++++++++++++++
arch/arm64/boot/dts/qcom/sdx75.dtsi | 74 +++++++
7 files changed, 455 insertions(+), 2 deletions(-)
create mode 100644 arch/arm64/boot/dts/qcom/pm7550ba.dtsi
create mode 100644 arch/arm64/boot/dts/qcom/pmx75.dtsi
--
2.7.4
Add dtsi for pmx75 PMIC found in Qualcomm platforms.
Signed-off-by: Rohit Agarwal <[email protected]>
---
arch/arm64/boot/dts/qcom/pmx75.dtsi | 64 +++++++++++++++++++++++++++++++++++++
1 file changed, 64 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/pmx75.dtsi
diff --git a/arch/arm64/boot/dts/qcom/pmx75.dtsi b/arch/arm64/boot/dts/qcom/pmx75.dtsi
new file mode 100644
index 0000000..373e45f
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pmx75.dtsi
@@ -0,0 +1,64 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+ thermal-zones {
+ pmx75-thermal {
+ polling-delay-passive = <100>;
+ polling-delay = <0>;
+
+ thermal-sensors = <&pmx75_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+
+ trip2 {
+ temperature = <145000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+ };
+};
+
+&spmi_bus {
+ pmx75: pmic@1 {
+ compatible = "qcom,pmx75", "qcom,spmi-pmic";
+ reg = <1 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmx75_temp_alarm: temp-alarm@a00 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0xa00>;
+ interrupts = <0x1 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ pmx75_gpios: gpio@8800 {
+ compatible = "qcom,pmx75-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pmx75_gpios 0 0 16>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+};
--
2.7.4
On 7.08.2023 14:28, Rohit Agarwal wrote:
> Hi,
>
> Changes in v2:
> - Added compatible for pm7550ba for eusb2 repeater and used it in DT.
> - Addressed some minor comments from Konrad to add fixes tag, labels
> and update the labels
>
> This series add support of pmics that are found in SDX75 platform and
> add the corresponding regulators in the IDP platform as well.
> It also parallely updates the pmic found in SDX65 to PM7250b and add pinctrl
> support for the same pmic chip.
> This series is based on the new header inclusion[1] and movement of the
> regulators level from rpmpd to rpmhpd[2].
> This series can be picked after successfully picking [2] and [3] as [1] has
> already been applied.
>
> [1] https://lore.kernel.org/all/[email protected]/
> [2] https://lore.kernel.org/all/[email protected]/
> [3] https://lore.kernel.org/all/[email protected]/
>
> Thanks,
> Rohit.
Since you resent this (as mentioned in the first thread with "v2" [1]),
the subject should be [PATCH RESEND ...]
Konrad
Add a dt-bindings compatible string for the Qualcomm's PM7550BA PMIC.
Signed-off-by: Rohit Agarwal <[email protected]>
---
.../devicetree/bindings/phy/qcom,snps-eusb2-repeater.yaml | 7 ++++++-
1 file changed, 6 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/phy/qcom,snps-eusb2-repeater.yaml b/Documentation/devicetree/bindings/phy/qcom,snps-eusb2-repeater.yaml
index 083fda5..029569d 100644
--- a/Documentation/devicetree/bindings/phy/qcom,snps-eusb2-repeater.yaml
+++ b/Documentation/devicetree/bindings/phy/qcom,snps-eusb2-repeater.yaml
@@ -15,7 +15,12 @@ description:
properties:
compatible:
- const: qcom,pm8550b-eusb2-repeater
+ oneOf:
+ - items:
+ - enum:
+ - qcom,pm7550ba-eusb2-repeater
+ - const: qcom,pm8550b-eusb2-repeater
+ - const: qcom,pm8550b-eusb2-repeater
reg:
maxItems: 1
--
2.7.4
Update the pmic used in sdx65 platform to pm7250b.
Fixes: 26380f298b2b (ARM: dts: qcom: sdx65-mtp: Add pmk8350b and pm8150b pmic)
Signed-off-by: Rohit Agarwal <[email protected]>
---
arch/arm/boot/dts/qcom/qcom-sdx65-mtp.dts | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/qcom/qcom-sdx65-mtp.dts b/arch/arm/boot/dts/qcom/qcom-sdx65-mtp.dts
index 02d8d6e..fcf1c51 100644
--- a/arch/arm/boot/dts/qcom/qcom-sdx65-mtp.dts
+++ b/arch/arm/boot/dts/qcom/qcom-sdx65-mtp.dts
@@ -7,7 +7,7 @@
#include "qcom-sdx65.dtsi"
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
#include <arm64/qcom/pmk8350.dtsi>
-#include <arm64/qcom/pm8150b.dtsi>
+#include <arm64/qcom/pm7250b.dtsi>
#include "qcom-pmx65.dtsi"
/ {
--
2.7.4