Hi,
This series adds device tree overlay for NAND expansion card for AM642-EVM.
cheers,
-roger
Changelog:
---------
v2:
- Drop patch "arm64: dts: ti: Enable support for overlays for relevant boards"
- Don't leave k3-am642-evm-nand.dtbo as an orphan. Make k3-am642-evm-nand.dtb
with the overlay applied on the base board.
- Add patch "arm64: dts: ti: k3-am64: Add GPIO expander on I2C0"
Roger Quadros (2):
arm64: dts: ti: am642-evm: Add overlay for NAND expansion card
arm64: dts: ti: k3-am64: Add GPIO expander on I2C0
arch/arm64/boot/dts/ti/Makefile | 3 +-
arch/arm64/boot/dts/ti/k3-am642-evm-nand.dtso | 140 ++++++++++++++++++
arch/arm64/boot/dts/ti/k3-am642-evm.dts | 9 ++
3 files changed, 151 insertions(+), 1 deletion(-)
create mode 100644 arch/arm64/boot/dts/ti/k3-am642-evm-nand.dtso
base-commit: 0bb80ecc33a8fb5a682236443c1e740d5c917d1d
--
2.34.1
The NAND expansion card plugs in over the HSE (High Speed Expansion)
connector. Add support for it.
Signed-off-by: Roger Quadros <[email protected]>
---
arch/arm64/boot/dts/ti/Makefile | 3 +-
arch/arm64/boot/dts/ti/k3-am642-evm-nand.dtso | 140 ++++++++++++++++++
2 files changed, 142 insertions(+), 1 deletion(-)
create mode 100644 arch/arm64/boot/dts/ti/k3-am642-evm-nand.dtso
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index e7b8e2e7f083..ad5f688df430 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -28,7 +28,8 @@ dtb-$(CONFIG_ARCH_K3) += k3-am62a7-sk.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am62p5-sk.dtb
# Boards with AM64x SoC
-dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb
+k3-am642-evm-nand-dtbs := k3-am642-evm.dtb k3-am642-evm-nand.dtbo
+dtb-$(CONFIG_ARCH_K3) += k3-am642-evm-nand.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am642-phyboard-electra-rdk.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am642-sk.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am642-tqma64xxl-mbax4xxl.dtb
diff --git a/arch/arm64/boot/dts/ti/k3-am642-evm-nand.dtso b/arch/arm64/boot/dts/ti/k3-am642-evm-nand.dtso
new file mode 100644
index 000000000000..12593836eaab
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am642-evm-nand.dtso
@@ -0,0 +1,140 @@
+// SPDX-License-Identifier: GPL-2.0
+/**
+ * DT overlay for HSE NAND expansion card on AM642 EVM
+ *
+ * Copyright (C) 2021-2023 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "k3-pinctrl.h"
+
+&main_pmx0 {
+ gpmc0_pins_default: gpmc0-pins-default {
+ pinctrl-single,pins = <
+ AM64X_IOPAD(0x0094, PIN_INPUT, 7) /* (T19) GPMC0_BE1n.GPIO0_36 */
+
+ AM64X_IOPAD(0x003c, PIN_INPUT, 0) /* (T20) GPMC0_AD0 */
+ AM64X_IOPAD(0x0040, PIN_INPUT, 0) /* (U21) GPMC0_AD1 */
+ AM64X_IOPAD(0x0064, PIN_INPUT, 0) /* (R16) GPMC0_AD10 */
+ AM64X_IOPAD(0x0068, PIN_INPUT, 0) /* (W20) GPMC0_AD11 */
+ AM64X_IOPAD(0x006c, PIN_INPUT, 0) /* (W21) GPMC0_AD12 */
+ AM64X_IOPAD(0x0070, PIN_INPUT, 0) /* (V18) GPMC0_AD13 */
+ AM64X_IOPAD(0x0074, PIN_INPUT, 0) /* (Y21) GPMC0_AD14 */
+ AM64X_IOPAD(0x0078, PIN_INPUT, 0) /* (Y20) GPMC0_AD15 */
+ AM64X_IOPAD(0x0044, PIN_INPUT, 0) /* (T18) GPMC0_AD2 */
+ AM64X_IOPAD(0x0048, PIN_INPUT, 0) /* (U20) GPMC0_AD3 */
+ AM64X_IOPAD(0x004c, PIN_INPUT, 0) /* (U18) GPMC0_AD4 */
+ AM64X_IOPAD(0x0050, PIN_INPUT, 0) /* (U19) GPMC0_AD5 */
+ AM64X_IOPAD(0x0054, PIN_INPUT, 0) /* (V20) GPMC0_AD6 */
+ AM64X_IOPAD(0x0058, PIN_INPUT, 0) /* (V21) GPMC0_AD7 */
+ AM64X_IOPAD(0x005c, PIN_INPUT, 0) /* (V19) GPMC0_AD8 */
+ AM64X_IOPAD(0x0060, PIN_INPUT, 0) /* (T17) GPMC0_AD9 */
+ AM64X_IOPAD(0x0098, PIN_INPUT_PULLUP, 0) /* (W19) GPMC0_WAIT0 */
+ AM64X_IOPAD(0x009c, PIN_INPUT_PULLUP, 0) /* (Y18) GPMC0_WAIT1 */
+ AM64X_IOPAD(0x00a8, PIN_OUTPUT_PULLUP, 0) /* (R19) GPMC0_CSn0 */
+ AM64X_IOPAD(0x00ac, PIN_OUTPUT_PULLUP, 0) /* (R20) GPMC0_CSn1 */
+ AM64X_IOPAD(0x00b0, PIN_OUTPUT_PULLUP, 0) /* (P19) GPMC0_CSn2 */
+ AM64X_IOPAD(0x00b4, PIN_OUTPUT_PULLUP, 0) /* (R21) GPMC0_CSn3 */
+ AM64X_IOPAD(0x007c, PIN_OUTPUT, 0) /* (R17) GPMC0_CLK */
+ AM64X_IOPAD(0x0084, PIN_OUTPUT, 0) /* (P16) GPMC0_ADVn_ALE */
+ AM64X_IOPAD(0x0088, PIN_OUTPUT, 0) /* (R18) GPMC0_OEn_REn */
+ AM64X_IOPAD(0x008c, PIN_OUTPUT, 0) /* (T21) GPMC0_WEn */
+ AM64X_IOPAD(0x0090, PIN_OUTPUT, 0) /* (P17) GPMC0_BE0n_CLE */
+ AM64X_IOPAD(0x00a0, PIN_OUTPUT_PULLUP, 0) /* (N16) GPMC0_WPn */
+ AM64X_IOPAD(0x00a4, PIN_OUTPUT, 0) /* (N17) GPMC0_DIR */
+ >;
+ };
+};
+
+&main_gpio0 {
+ gpio0-36 {
+ gpio-hog;
+ gpios = <36 0>;
+ input;
+ line-name = "GPMC0_MUX_DIR";
+ };
+};
+
+&elm0 {
+ status = "okay";
+};
+
+&gpmc0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpmc0_pins_default>;
+ ranges = <0 0 0x00 0x51000000 0x01000000>; /* CS0 space. Min partition = 16MB */
+ #address-cells = <2>;
+ #size-cells = <1>;
+
+ nand@0,0 {
+ compatible = "ti,am64-nand";
+ reg = <0 0 64>; /* device IO registers */
+ interrupt-parent = <&gpmc0>;
+ interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+ <1 IRQ_TYPE_NONE>; /* termcount */
+ rb-gpios = <&gpmc0 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
+ ti,nand-xfer-type = "prefetch-polled";
+ ti,nand-ecc-opt = "bch8"; /* BCH8: Bootrom limitation */
+ ti,elm-id = <&elm0>;
+ nand-bus-width = <8>;
+ gpmc,device-width = <1>;
+ gpmc,sync-clk-ps = <0>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <40>;
+ gpmc,cs-wr-off-ns = <40>;
+ gpmc,adv-on-ns = <0>;
+ gpmc,adv-rd-off-ns = <25>;
+ gpmc,adv-wr-off-ns = <25>;
+ gpmc,we-on-ns = <0>;
+ gpmc,we-off-ns = <20>;
+ gpmc,oe-on-ns = <3>;
+ gpmc,oe-off-ns = <30>;
+ gpmc,access-ns = <30>;
+ gpmc,rd-cycle-ns = <40>;
+ gpmc,wr-cycle-ns = <40>;
+ gpmc,bus-turnaround-ns = <0>;
+ gpmc,cycle2cycle-delay-ns = <0>;
+ gpmc,clk-activation-ns = <0>;
+ gpmc,wr-access-ns = <40>;
+ gpmc,wr-data-mux-bus-ns = <0>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "NAND.tiboot3";
+ reg = <0x00000000 0x00200000>; /* 2M */
+ };
+ partition@200000 {
+ label = "NAND.tispl";
+ reg = <0x00200000 0x00200000>; /* 2M */
+ };
+ partition@400000 {
+ label = "NAND.tiboot3.backup"; /* 2M */
+ reg = <0x00400000 0x00200000>; /* BootROM looks at 4M */
+ };
+ partition@600000 {
+ label = "NAND.u-boot";
+ reg = <0x00600000 0x00400000>; /* 4M */
+ };
+ partition@a00000 {
+ label = "NAND.u-boot-env";
+ reg = <0x00a00000 0x00040000>; /* 256K */
+ };
+ partition@a40000 {
+ label = "NAND.u-boot-env.backup";
+ reg = <0x00a40000 0x00040000>; /* 256K */
+ };
+ partition@a80000 {
+ label = "NAND.file-system";
+ reg = <0x00a80000 0x3f580000>;
+ };
+ };
+ };
+};
--
2.34.1
A TCA9554 GPIO expander is present on I2C0. Add it.
Signed-off-by: Roger Quadros <[email protected]>
---
arch/arm64/boot/dts/ti/k3-am642-evm.dts | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am642-evm.dts b/arch/arm64/boot/dts/ti/k3-am642-evm.dts
index b4a1f73d4fb1..3dccc597f516 100644
--- a/arch/arm64/boot/dts/ti/k3-am642-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-am642-evm.dts
@@ -392,6 +392,15 @@ &main_i2c0 {
pinctrl-0 = <&main_i2c0_pins_default>;
clock-frequency = <400000>;
+ gpio@38 {
+ /* TCA9554 */
+ compatible = "nxp,pca9554";
+ reg = <0x38>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "HSE_DETECT";
+ };
+
eeprom@50 {
/* AT24CM01 */
compatible = "atmel,24c1024";
--
2.34.1
Hi Roger Quadros,
On Sat, 23 Sep 2023 11:00:44 +0300, Roger Quadros wrote:
> This series adds device tree overlay for NAND expansion card for AM642-EVM.
>
> cheers,
> -roger
>
> Changelog:
> ---------
> v2:
> - Drop patch "arm64: dts: ti: Enable support for overlays for relevant boards"
> - Don't leave k3-am642-evm-nand.dtbo as an orphan. Make k3-am642-evm-nand.dtb
> with the overlay applied on the base board.
> - Add patch "arm64: dts: ti: k3-am64: Add GPIO expander on I2C0"
>
> [...]
I have applied the following to branch ti-k3-dts-next on [1].
Thank you!
[1/2] arm64: dts: ti: am642-evm: Add overlay for NAND expansion card
commit: 45a0c06571e1388f8cd3e0e0b1db9927db06cf2a
[2/2] arm64: dts: ti: k3-am64: Add GPIO expander on I2C0
commit: 0ce486452bf216d502017b1db066a80b546d0f87
All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent up the chain during
the next merge window (or sooner if it is a relevant bug fix), however if
problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying
to this mail.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux.git
--
Vignesh