Add CAN Nodes for 18 CAN instances present in main domain and 2 CAN
instances present in the mcu domain. CAN instance 0 in main domain is
enabled on transceiver 0 in J7200 SoM. CAN instance 0 and 1 in mcu
domain and CAN instance 3 in main domain is enabled on transceivers
1, 2 and 3 respectively on common processor board.
Rebased to next-20240130
Bhavya Kapoor (3):
arm64: dts: ti: k3-j7200: Add support for CAN nodes
arm64: dts: ti: k3-j7200-som-p0: Add support for CAN instance 0 in
main domain
arm64: dts: ti: k3-j7200: Add support for multiple CAN instances
.../dts/ti/k3-j7200-common-proc-board.dts | 83 ++++++
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 270 ++++++++++++++++++
.../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 30 ++
arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 35 +++
4 files changed, 418 insertions(+)
--
2.34.1
CAN instance 0 in the main domain is brought on the J7200 SoM through
header J1. Thus, Add transceiver dt node to add support for this CAN
instance.
Also, add the mux dt nodes to route CAN High and Low lines coming
from the SoC to the Common Processor Board.
Signed-off-by: Bhavya Kapoor <[email protected]>
---
arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 35 +++++++++++++++++++++
1 file changed, 35 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
index ea47f10d393a..0010600b8176 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
@@ -5,6 +5,8 @@
/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+
#include "k3-j7200.dtsi"
/ {
@@ -80,6 +82,25 @@ rtos_ipc_memory_region: ipc-memories@a4000000 {
no-map;
};
};
+
+ mux0: mux-controller {
+ compatible = "gpio-mux";
+ #mux-state-cells = <1>;
+ mux-gpios = <&exp_som 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ mux1: mux-controller {
+ compatible = "gpio-mux";
+ #mux-state-cells = <1>;
+ mux-gpios = <&exp_som 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ transceiver0: can-phy0 {
+ /* standby pin has been grounded by default */
+ compatible = "ti,tcan1042";
+ #phy-cells = <0>;
+ max-bitrate = <5000000>;
+ };
};
&wkup_pmx0 {
@@ -142,6 +163,13 @@ J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
>;
};
+
+ main_mcan0_pins_default: main-mcan0-default-pins {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x24, PIN_INPUT, 0) /* (V20) MCAN0_RX */
+ J721E_IOPAD(0x20, PIN_OUTPUT, 0) /* (V18) MCAN0_TX */
+ >;
+ };
};
&hbmc {
@@ -478,3 +506,10 @@ partition@3fc0000 {
};
};
};
+
+&main_mcan0 {
+ status = "okay";
+ pinctrl-0 = <&main_mcan0_pins_default>;
+ pinctrl-names = "default";
+ phys = <&transceiver0>;
+};
--
2.34.1
CAN instances 0 and 1 in the mcu domain are brought on the common
processor board through headers J30 and J31 respectively. Thus, add
their respective transceivers 1 and 2 dt nodes to add support for
these CAN instances.
CAN instance 3 in the main domain is brought on the common
processor board through header J27. The CAN High and Low lines
from the SoC are routed through a mux on the SoM. The select lines need
to be set for the CAN signals to get connected to the transceiver 3 on
the common processor board. Therefore, add transceiver dt nodes to add
support for this CAN instance.
Signed-off-by: Bhavya Kapoor <[email protected]>
---
.../dts/ti/k3-j7200-common-proc-board.dts | 83 +++++++++++++++++++
1 file changed, 83 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index cee2b4b0eb87..63b03dc326fa 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -88,6 +88,34 @@ vdd_sd_dv: gpio-regulator-TLV71033 {
states = <1800000 0x0>,
<3300000 0x1>;
};
+
+ transceiver1: can-phy1 {
+ compatible = "ti,tcan1043";
+ #phy-cells = <0>;
+ max-bitrate = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_mcan0_gpio_pins_default>;
+ standby-gpios = <&wkup_gpio0 58 GPIO_ACTIVE_LOW>;
+ enable-gpios = <&wkup_gpio0 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ transceiver2: can-phy2 {
+ compatible = "ti,tcan1042";
+ #phy-cells = <0>;
+ max-bitrate = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_mcan1_gpio_pins_default>;
+ standby-gpios = <&wkup_gpio0 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ transceiver3: can-phy3 {
+ compatible = "ti,tcan1043";
+ #phy-cells = <0>;
+ max-bitrate = <5000000>;
+ standby-gpios = <&exp2 7 GPIO_ACTIVE_LOW>;
+ enable-gpios = <&exp2 6 GPIO_ACTIVE_HIGH>;
+ mux-states = <&mux0 1>;
+ };
};
&wkup_pmx0 {
@@ -138,6 +166,33 @@ J721E_WKUP_IOPAD(0x0034, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
J721E_WKUP_IOPAD(0x0030, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
>;
};
+
+ mcu_mcan0_pins_default: mcu-mcan0-default-pins {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0x54, PIN_INPUT, 0) /* (A17) MCU_MCAN0_RX */
+ J721E_WKUP_IOPAD(0x50, PIN_OUTPUT, 0) /* (A16) MCU_MCAN0_TX */
+ >;
+ };
+
+ mcu_mcan1_pins_default: mcu-mcan1-default-pins {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0x6c, PIN_INPUT, 0) /* (B16) WKUP_GPIO0_5.MCU_MCAN1_RX */
+ J721E_WKUP_IOPAD(0x68, PIN_OUTPUT, 0) /* (D13) WKUP_GPIO0_4.MCU_MCAN1_TX */
+ >;
+ };
+
+ mcu_mcan0_gpio_pins_default: mcu-mcan0-gpio-default-pins {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0x58, PIN_INPUT, 7) /* (B18) WKUP_GPIO0_0 */
+ J721E_WKUP_IOPAD(0x40, PIN_INPUT, 7) /* (B17) MCU_SPI0_D1 */
+ >;
+ };
+
+ mcu_mcan1_gpio_pins_default: mcu-mcan1-gpio-default-pins {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0x60, PIN_INPUT, 7) /* (D14) WKUP_GPIO0_2 */
+ >;
+ };
};
&main_pmx0 {
@@ -189,6 +244,13 @@ vdd_sd_dv_pins_default: vdd-sd-dv-default-pins {
J721E_IOPAD(0xd0, PIN_OUTPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */
>;
};
+
+ main_mcan3_pins_default: main-mcan3-default-pins {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x3c, PIN_INPUT, 0) /* (W16) MCAN3_RX */
+ J721E_IOPAD(0x38, PIN_OUTPUT, 0) /* (Y21) MCAN3_TX */
+ >;
+ };
};
&main_pmx1 {
@@ -394,3 +456,24 @@ &pcie1_ep {
num-lanes = <2>;
status = "disabled";
};
+
+&mcu_mcan0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_mcan0_pins_default>;
+ phys = <&transceiver1>;
+};
+
+&mcu_mcan1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_mcan1_pins_default>;
+ phys = <&transceiver2>;
+};
+
+&main_mcan3 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mcan3_pins_default>;
+ phys = <&transceiver3>;
+};
--
2.34.1
Add support for 18 CAN controllers in main domain and 2 CAN controllers
present in mcu domain. All the CAN controllers support classic CAN
messages as well as CAN_FD messages.
Signed-off-by: Bhavya Kapoor <[email protected]>
---
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 270 ++++++++++++++++++
.../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 30 ++
2 files changed, 300 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
index da67bf8fe703..58fd67be213f 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
@@ -895,6 +895,276 @@ main_gpio6: gpio@630000 {
status = "disabled";
};
+ main_mcan0: can@2701000 {
+ compatible = "bosch,m_can";
+ reg = <0x00 0x02701000 0x00 0x200>,
+ <0x00 0x02708000 0x00 0x8000>;
+ reg-names = "m_can", "message_ram";
+ power-domains = <&k3_pds 156 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 156 0>, <&k3_clks 156 2>;
+ clock-names = "hclk", "cclk";
+ interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "int0", "int1";
+ bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+ status = "disabled";
+ };
+
+ main_mcan1: can@2711000 {
+ compatible = "bosch,m_can";
+ reg = <0x00 0x02711000 0x00 0x200>,
+ <0x00 0x02718000 0x00 0x8000>;
+ reg-names = "m_can", "message_ram";
+ power-domains = <&k3_pds 158 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 158 0>, <&k3_clks 158 2>;
+ clock-names = "hclk", "cclk";
+ interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "int0", "int1";
+ bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+ status = "disabled";
+ };
+
+ main_mcan2: can@2721000 {
+ compatible = "bosch,m_can";
+ reg = <0x00 0x02721000 0x00 0x200>,
+ <0x00 0x02728000 0x00 0x8000>;
+ reg-names = "m_can", "message_ram";
+ power-domains = <&k3_pds 160 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 160 0>, <&k3_clks 160 2>;
+ clock-names = "hclk", "cclk";
+ interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "int0", "int1";
+ bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+ status = "disabled";
+ };
+
+ main_mcan3: can@2731000 {
+ compatible = "bosch,m_can";
+ reg = <0x00 0x02731000 0x00 0x200>,
+ <0x00 0x02738000 0x00 0x8000>;
+ reg-names = "m_can", "message_ram";
+ power-domains = <&k3_pds 161 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 161 0>, <&k3_clks 161 2>;
+ clock-names = "hclk", "cclk";
+ interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "int0", "int1";
+ bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+ status = "disabled";
+ };
+
+ main_mcan4: can@2741000 {
+ compatible = "bosch,m_can";
+ reg = <0x00 0x02741000 0x00 0x200>,
+ <0x00 0x02748000 0x00 0x8000>;
+ reg-names = "m_can", "message_ram";
+ power-domains = <&k3_pds 162 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 162 0>, <&k3_clks 162 2>;
+ clock-names = "hclk", "cclk";
+ interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "int0", "int1";
+ bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+ status = "disabled";
+ };
+
+ main_mcan5: can@2751000 {
+ compatible = "bosch,m_can";
+ reg = <0x00 0x02751000 0x00 0x200>,
+ <0x00 0x02758000 0x00 0x8000>;
+ reg-names = "m_can", "message_ram";
+ power-domains = <&k3_pds 163 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 163 0>, <&k3_clks 163 2>;
+ clock-names = "hclk", "cclk";
+ interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "int0", "int1";
+ bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+ status = "disabled";
+ };
+
+ main_mcan6: can@2761000 {
+ compatible = "bosch,m_can";
+ reg = <0x00 0x02761000 0x00 0x200>,
+ <0x00 0x02768000 0x00 0x8000>;
+ reg-names = "m_can", "message_ram";
+ power-domains = <&k3_pds 164 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 164 0>, <&k3_clks 164 2>;
+ clock-names = "hclk", "cclk";
+ interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "int0", "int1";
+ bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+ status = "disabled";
+ };
+
+ main_mcan7: can@2771000 {
+ compatible = "bosch,m_can";
+ reg = <0x00 0x02771000 0x00 0x200>,
+ <0x00 0x02778000 0x00 0x8000>;
+ reg-names = "m_can", "message_ram";
+ power-domains = <&k3_pds 165 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 165 0>, <&k3_clks 165 2>;
+ clock-names = "hclk", "cclk";
+ interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "int0", "int1";
+ bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+ status = "disabled";
+ };
+
+ main_mcan8: can@2781000 {
+ compatible = "bosch,m_can";
+ reg = <0x00 0x02781000 0x00 0x200>,
+ <0x00 0x02788000 0x00 0x8000>;
+ reg-names = "m_can", "message_ram";
+ power-domains = <&k3_pds 166 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 166 0>, <&k3_clks 166 2>;
+ clock-names = "hclk", "cclk";
+ interrupts = <GIC_SPI 576 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 577 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "int0", "int1";
+ bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+ status = "disabled";
+ };
+
+ main_mcan9: can@2791000 {
+ compatible = "bosch,m_can";
+ reg = <0x00 0x02791000 0x00 0x200>,
+ <0x00 0x02798000 0x00 0x8000>;
+ reg-names = "m_can", "message_ram";
+ power-domains = <&k3_pds 167 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 167 0>, <&k3_clks 167 2>;
+ clock-names = "hclk", "cclk";
+ interrupts = <GIC_SPI 579 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 580 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "int0", "int1";
+ bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+ status = "disabled";
+ };
+
+ main_mcan10: can@27a1000 {
+ compatible = "bosch,m_can";
+ reg = <0x00 0x027a1000 0x00 0x200>,
+ <0x00 0x027a8000 0x00 0x8000>;
+ reg-names = "m_can", "message_ram";
+ power-domains = <&k3_pds 168 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 168 0>, <&k3_clks 168 2>;
+ clock-names = "hclk", "cclk";
+ interrupts = <GIC_SPI 582 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "int0", "int1";
+ bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+ status = "disabled";
+ };
+
+ main_mcan11: can@27b1000 {
+ compatible = "bosch,m_can";
+ reg = <0x00 0x027b1000 0x00 0x200>,
+ <0x00 0x027b8000 0x00 0x8000>;
+ reg-names = "m_can", "message_ram";
+ power-domains = <&k3_pds 169 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 169 0>, <&k3_clks 169 2>;
+ clock-names = "hclk", "cclk";
+ interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "int0", "int1";
+ bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+ status = "disabled";
+ };
+
+ main_mcan12: can@27c1000 {
+ compatible = "bosch,m_can";
+ reg = <0x00 0x027c1000 0x00 0x200>,
+ <0x00 0x027c8000 0x00 0x8000>;
+ reg-names = "m_can", "message_ram";
+ power-domains = <&k3_pds 170 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 170 0>, <&k3_clks 170 2>;
+ clock-names = "hclk", "cclk";
+ interrupts = <GIC_SPI 588 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 589 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "int0", "int1";
+ bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+ status = "disabled";
+ };
+
+ main_mcan13: can@27d1000 {
+ compatible = "bosch,m_can";
+ reg = <0x00 0x027d1000 0x00 0x200>,
+ <0x00 0x027d8000 0x00 0x8000>;
+ reg-names = "m_can", "message_ram";
+ power-domains = <&k3_pds 171 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 171 0>, <&k3_clks 171 2>;
+ clock-names = "hclk", "cclk";
+ interrupts = <GIC_SPI 591 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 592 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "int0", "int1";
+ bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+ status = "disabled";
+ };
+
+ main_mcan14: can@2681000 {
+ compatible = "bosch,m_can";
+ reg = <0x00 0x02681000 0x00 0x200>,
+ <0x00 0x02688000 0x00 0x8000>;
+ reg-names = "m_can", "message_ram";
+ power-domains = <&k3_pds 150 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 150 0>, <&k3_clks 150 2>;
+ clock-names = "hclk", "cclk";
+ interrupts = <GIC_SPI 594 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 595 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "int0", "int1";
+ bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+ status = "disabled";
+ };
+
+ main_mcan15: can@2691000 {
+ compatible = "bosch,m_can";
+ reg = <0x00 0x02691000 0x00 0x200>,
+ <0x00 0x02698000 0x00 0x8000>;
+ reg-names = "m_can", "message_ram";
+ power-domains = <&k3_pds 151 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 151 0>, <&k3_clks 151 2>;
+ clock-names = "hclk", "cclk";
+ interrupts = <GIC_SPI 597 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 598 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "int0", "int1";
+ bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+ status = "disabled";
+ };
+
+ main_mcan16: can@26a1000 {
+ compatible = "bosch,m_can";
+ reg = <0x00 0x026a1000 0x00 0x200>,
+ <0x00 0x026a8000 0x00 0x8000>;
+ reg-names = "m_can", "message_ram";
+ power-domains = <&k3_pds 152 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 152 0>, <&k3_clks 152 2>;
+ clock-names = "hclk", "cclk";
+ interrupts = <GIC_SPI 784 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 785 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "int0", "int1";
+ bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+ status = "disabled";
+ };
+
+ main_mcan17: can@26b1000 {
+ compatible = "bosch,m_can";
+ reg = <0x00 0x026b1000 0x00 0x200>,
+ <0x00 0x026b8000 0x00 0x8000>;
+ reg-names = "m_can", "message_ram";
+ power-domains = <&k3_pds 153 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 153 0>, <&k3_clks 153 2>;
+ clock-names = "hclk", "cclk";
+ interrupts = <GIC_SPI 787 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 788 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "int0", "int1";
+ bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+ status = "disabled";
+ };
+
main_spi0: spi@2100000 {
compatible = "ti,am654-mcspi","ti,omap4-mcspi";
reg = <0x00 0x02100000 0x00 0x400>;
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
index 60b26374ae0c..11bda5c70655 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
@@ -655,4 +655,34 @@ mcu_esm: esm@40800000 {
ti,esm-pins = <95>;
bootph-pre-ram;
};
+
+ mcu_mcan0: can@40528000 {
+ compatible = "bosch,m_can";
+ reg = <0x00 0x40528000 0x00 0x200>,
+ <0x00 0x40500000 0x00 0x8000>;
+ reg-names = "m_can", "message_ram";
+ power-domains = <&k3_pds 172 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 172 0>, <&k3_clks 172 2>;
+ clock-names = "hclk", "cclk";
+ interrupts = <GIC_SPI 832 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 833 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "int0", "int1";
+ bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+ status = "disabled";
+ };
+
+ mcu_mcan1: can@40568000 {
+ compatible = "bosch,m_can";
+ reg = <0x00 0x40568000 0x00 0x200>,
+ <0x00 0x40540000 0x00 0x8000>;
+ reg-names = "m_can", "message_ram";
+ power-domains = <&k3_pds 173 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 173 0>, <&k3_clks 173 2>;
+ clock-names = "hclk", "cclk";
+ interrupts = <GIC_SPI 835 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 836 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "int0", "int1";
+ bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+ status = "disabled";
+ };
};
--
2.34.1
Hi Bhavya Kapoor,
On Tue, 30 Jan 2024 15:50:41 +0530, Bhavya Kapoor wrote:
> Add CAN Nodes for 18 CAN instances present in main domain and 2 CAN
> instances present in the mcu domain. CAN instance 0 in main domain is
> enabled on transceiver 0 in J7200 SoM. CAN instance 0 and 1 in mcu
> domain and CAN instance 3 in main domain is enabled on transceivers
> 1, 2 and 3 respectively on common processor board.
>
> Rebased to next-20240130
>
> [...]
I have applied the following to branch ti-k3-dts-next on [1].
Thank you!
[1/3] arm64: dts: ti: k3-j7200: Add support for CAN nodes
commit: 03b94719ec31ba0e6580f512cba9100bb560e17b
[2/3] arm64: dts: ti: k3-j7200-som-p0: Add support for CAN instance 0 in main domain
commit: da23e8d1124b93e468a24247021ace34902a9895
[3/3] arm64: dts: ti: k3-j7200: Add support for multiple CAN instances
commit: 6b80695f93b2253dbf669323154eb06b162f55ef
All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent up the chain during
the next merge window (or sooner if it is a relevant bug fix), however if
problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying
to this mail.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux.git
--
Vignesh