Hello List,
on shutdown the following lines are displayed, but _not_ logged to
/var/log/messages:
Going to halt the system ...
Synchronizing SCSI caches: sda FAILED
status = 1, message = 00, host = 0, driver = 08
Current sd?: sense = 70 5
ASC=20 ASCQ= 0
Raw sense data:0x70 0x00 0x05 0x00 0x00 0x00 0x00 0x0e 0x00 0x00 0x00
0x00 0x20 0x00 0x00 0xc0 0x00 0x00 0x00 0x00 0x00
Power off.
Information about my SCSIs:
/var/log/messages:
==================
Dec 6 21:00:24 brood kernel: SCSI subsystem driver Revision: 1.00
Dec 6 21:00:24 brood kernel: scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.4
Dec 6 21:00:24 brood kernel: <Adaptec 2940 SCSI adapter>
Dec 6 21:00:24 brood kernel: aic7870: Single Channel A, SCSI Id=0, 16/253 SCBs
Dec 6 21:00:24 brood kernel:
Dec 6 21:00:24 brood kernel: (scsi0:A:1): 10.000MB/s transfers (10.000MHz, offset 15)
Dec 6 21:00:24 brood kernel: Vendor: SEAGATE Model: ST52160N Rev: 0285
Dec 6 21:00:24 brood kernel: Type: Direct-Access ANSI SCSI revision: 02
Dec 6 21:00:24 brood kernel: SCSI device sda: drive cache: write back
Dec 6 21:00:24 brood kernel: SCSI device sda: 4238282 512-byte hdwr sectors (2170 MB)
Dec 6 21:00:24 brood kernel: /dev/scsi/host0/bus0/target1/lun0: p1 p2
Dec 6 21:00:24 brood kernel: Attached scsi disk sda at scsi0, channel 0, id 1, lun 0
/proc/scsi/scsi:
================
Attached devices:
Host: scsi0 Channel: 00 Id: 01 Lun: 00
Vendor: SEAGATE Model: ST52160N Rev: 0285
Type: Direct-Access ANSI SCSI revision: 02
/proc/scsi/aic7xxx/0:
=====================
Adaptec AIC7xxx driver version: 6.2.4
aic7870: Single Channel A, SCSI Id=0, 16/253 SCBs
Channel A Target 0 Negotiation Settings
User: 10.000MB/s transfers (10.000MHz, offset 255)
Channel A Target 1 Negotiation Settings
User: 10.000MB/s transfers (10.000MHz, offset 255)
Goal: 10.000MB/s transfers (10.000MHz, offset 15)
Curr: 10.000MB/s transfers (10.000MHz, offset 15)
Channel A Target 1 Lun 0 Settings
Commands Queued 155
Commands Active 0
Command Openings 1
Max Tagged Openings 0
Device Queue Frozen Count 0
Channel A Target 2 Negotiation Settings
User: 10.000MB/s transfers (10.000MHz, offset 255)
Channel A Target 3 Negotiation Settings
User: 10.000MB/s transfers (10.000MHz, offset 255)
Channel A Target 4 Negotiation Settings
User: 10.000MB/s transfers (10.000MHz, offset 255)
Channel A Target 5 Negotiation Settings
User: 10.000MB/s transfers (10.000MHz, offset 255)
Channel A Target 6 Negotiation Settings
User: 10.000MB/s transfers (10.000MHz, offset 255)
Channel A Target 7 Negotiation Settings
User: 10.000MB/s transfers (10.000MHz, offset 255)
/proc/iomem:
============
...
e4000000-e4000fff : Adaptec AHA-2940/2940W / AIC
e4000000-e4000fff : aic7xxx
...
/proc/ioports:
==============
...
6000-60ff : Adaptec AHA-2940/2940W / AIC
6000-60ff : aic7xxx
...
any hints?
--
cheers,
Tobias
At Fri, 6 Dec 2002 22:34:44 +0100,
Tobias Rittweiler wrote:
> on shutdown the following lines are displayed, but _not_ logged to
> /var/log/messages:
>
> Going to halt the system ...
> Synchronizing SCSI caches: sda FAILED
> status = 1, message = 00, host = 0, driver = 08
> Current sd?: sense = 70 5
> ASC=20 ASCQ= 0
> Raw sense data:0x70 0x00 0x05 0x00 0x00 0x00 0x00 0x0e 0x00 0x00 0x00
> 0x00 0x20 0x00 0x00 0xc0 0x00 0x00 0x00 0x00 0x00
> Power off.
Your device cannot handle SYNCHRONIZED_CACHE command which flushes
Seagate ST52160N device cache during shutdown introduced in recent 2.5.
I think the below patch for 2.5.50 (and current BK) suppresses such
failure message.
--- drivers/scsi/sd.c 2002-11-23 06:40:54.000000000 +0900
+++ drivers/scsi/sd.c.new 2002-12-08 13:14:13.000000000 +0900
@@ -865,8 +865,10 @@
if(status_byte(the_result) == CHECK_CONDITION
&& (SRpnt->sr_sense_buffer[0] & 0x70) == 0x70
&& (SRpnt->sr_sense_buffer[2] & 0x0f) == ILLEGAL_REQUEST
- /* The next are ASC 0x24 ASCQ 0x00: Invalid field in CDB */
- && SRpnt->sr_sense_buffer[12] == 0x24
+ /* The next are ASC 0x24 ASCQ 0x00: Invalid field in CDB,
+ or ASC 0x20 ASCQ 0x00: Invalid command operation code. */
+ && (SRpnt->sr_sense_buffer[12] == 0x24 ||
+ SRpnt->sr_sense_buffer[12] == 0x20)
&& SRpnt->sr_sense_buffer[13] == 0x00) {
printk(KERN_NOTICE "SCSI device %s: cache data unavailable\n", diskname);
} else {
-- gotom