Hi,
Problems with Creative Webcam III. This worked fine
in test13-pre4, haven't tried pre5 & 6.
On boot:
usb_control/bulk_msg: timeout
usb_control/bulk_msg: timeout
usb.c: couldn't get all of config descriptors
usb.c: unable to get device 2 configuration (error=-110)
hub.c: USB new device connect on bus1/1, assigned device number 4
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=4 (error=-110)
On remove/reinsert:
hub.c: USB new device connect on bus1/1, assigned device number 5
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=5 (error=-110)
hub.c: USB new device connect on bus1/1, assigned device number 6
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=6 (error=-110)
USB controller is:
00:04.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 10) (prog-if
00 [UHCI])
Subsystem: Unknown device 0925:1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 5
Region 4: I/O ports at d400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
The only other thing of relevance in dmesg, is the flood of
irq warnings related to the two USB controllers on 4.2 & 4.3 :-
PCI: Found IRQ 5 for device 00:09.0
PCI: The same IRQ used for device 00:04.2
PCI: The same IRQ used for device 00:04.3
PCI: Found IRQ 5 for device 00:04.2
PCI: The same IRQ used for device 00:04.3
PCI: The same IRQ used for device 00:09.0
PCI: Found IRQ 5 for device 00:04.3
PCI: The same IRQ used for device 00:04.2
PCI: The same IRQ used for device 00:09.0
usb-uhci.c: USB UHCI at I/O 0xd000, IRQ 5
usb-uhci.c: Detected 2 ports
hub.c: USB new device connect on bus1/1, assigned device number 2
usb.c: new USB bus registered, assigned bus number 2
usb-uhci.c: interrupt, status 2, frame# 135
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: registered new driver ov511
ov511.c: ov511 driver version 1.28 registered
regards,
Davej.
--
| Dave Jones. http://www.suse.de/~davej
| SuSE Labs
On Sat, Dec 30, 2000 at 11:24:40PM +0000, [email protected] wrote:
> Problems with Creative Webcam III. This worked fine
> in test13-pre4, haven't tried pre5 & 6.
[snip]
> USB controller is:
>
> 00:04.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 10) (prog-if
> 00 [UHCI])
> Subsystem: Unknown device 0925:1234
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32, cache line size 08
> Interrupt: pin D routed to IRQ 5
> Region 4: I/O ports at d400 [size=32]
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
This looks like some kind of UHCI problem. I have the same camera
(well, it is a Creative Webcam plus, but same chipset) with an Intel
UHCI controller and I haven't seen any errors. Here is my USB
controller:
00:07.2 USB Controller: Intel Corporation 82440MX USB Universal Host
Controller (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at fcc0 [size=32]
Erik
--
J.A.K. (Erik) Mouw, Information and Communication Theory Group, Department
of Electrical Engineering, Faculty of Information Technology and Systems,
Delft University of Technology, PO BOX 5031, 2600 GA Delft, The Netherlands
Phone: +31-15-2783635 Fax: +31-15-2781843 Email: [email protected]
WWW: http://www-ict.its.tudelft.nl/~erik/