it's about 2.5.62
I can do a make bzImage correctly
I can do a make modules correctly
but
when I do a make modules_install I get a lot of
depmod: Unresolved Symbols in /lib/modules/2.5.62/xxxx/xxxxx/xxxx.ko
What ca I do in order to see what's happening?
Thanks.
=============================================================
Luis Miguel Garcia Mancebo
Ingenieria Tecnica en Informatica de Gestion
Universidad de Deusto / University of Deusto
Bilbao / Spain
=============================================================
man depmod
depmod -e
depmod -ae
Cheers,
Dick Johnson
Penguin : Linux version 2.4.18 on an i686 machine (797.90 BogoMips).
Why is the government concerned about the lunatic fringe? Think about it.
Luis Miguel Garcia wrote:
> it's about 2.5.62
>
> I can do a make bzImage correctly
> I can do a make modules correctly
>
> but
>
> when I do a make modules_install I get a lot of
> depmod: Unresolved Symbols in /lib/modules/2.5.62/xxxx/xxxxx/xxxx.ko
>
> What ca I do in order to see what's happening?
Do you have module-init-tools installed? Kernels since 2.5.48 require
differed module utilities.
hello:
Yes, it was missing module-init-tools. Now I have my kernel compiled but when I try to boot, I can only see
Uncompressing Kernel... booting linux....
and then I cannot see nothing more but the HD is going up and down during half a minute, so I think something is happening but my screen is not updating.
What can I test in order to boot my system?
I'm behing a Sony Vaio N505-VE laptop.
Thanks.
On Tue, 18 Feb 2003 09:43:49 -0500
John Weber <[email protected]> wrote:
> Luis Miguel Garcia wrote:
> > it's about 2.5.62
> >
> > I can do a make bzImage correctly
> > I can do a make modules correctly
> >
> > but
> >
> > when I do a make modules_install I get a lot of
> > depmod: Unresolved Symbols in /lib/modules/2.5.62/xxxx/xxxxx/xxxx.ko
> >
> > What ca I do in order to see what's happening?
>
> Do you have module-init-tools installed? Kernels since 2.5.48 require
> differed module utilities.
>
>
>
>
=============================================================
Luis Miguel Garcia Mancebo
Ingenieria Tecnica en Informatica de Gestion
Universidad de Deusto / University of Deusto
Bilbao / Spain
------------------------------------------------------------
there's no place that I could be without you
there's no place that I could gleam without you
there's no place that I could dream without you
there's no place that I could be without you
honestly
=============================================================
On Tuesday 18 February 2003 13:52, Luis Miguel Garcia wrote:
> hello:
>
> Yes, it was missing module-init-tools. Now I have my kernel compiled but
> when I try to boot, I can only see
>
> Uncompressing Kernel... booting linux....
>
> and then I cannot see nothing more but the HD is going up and down during
> half a minute, so I think something is happening but my screen is not
> updating.
>
> What can I test in order to boot my system?
>
> I'm behing a Sony Vaio N505-VE laptop.
Maybe the message below applies to you too.
On Wed, Feb 19, 2003 at 10:52:47AM +0100, Duncan Sands wrote:
> This is becoming a FAQ! Did you enable the console in your .config?
> CONFIG_VT=y
> CONFIG_VT_CONSOLE=y
> Most likely you chose to compile the input system as a module, which
> caused the console options to be autohorribly deselected. Just say 'y'
> for the input subsystem, at which point the console options will reappear,
> letting you select them.
> I hope this helps,
> Duncan.
--
GertJan