The bulk of the diff by far is various architecture updates, and in
particular bringing MIPS[64] a bit closer to being up-to-date for 2.6.x
But there's arm, alpha, h8300 and ia64 updates too.
Merging the SELinux security architecture also ends up growing the patch,
even though it may not be all that noticeable for most normal users.
For most x86 users, the CPU frequency updates, network driver updates, and
some USB updates are most likely to matter.
And this should fix the PCMCIA lock-up that a number of people have seen
happening since 2.5.71 or so. Thanks for people involved in testing and
fixing that one.
Also, Andrew fixed a read-ahead bug that was introduced in test2 that
could cause (non-readahead) IO failures under load.
Shortlog follows, full details in the BK trees and in the log on the
ftp/web sites.
Linus
----
Summary of changes from v2.6.0-test2 to v2.6.0-test3
====================================================
<nikkne:hotpop.com>:
o I2C: fix Kconfig info
Adam Belay:
o [PNP] Handle unset resources properly
o [PNP] Remove protocol_data from pnp_dev and pnp_card
o [PNPBIOS] Move Parsing Functions to the PnPBIOS driver
o [SOUND] Remove __(dev)initdata from all pnp sound drivers
o [PNPBIOS] Move low level code into a separate file
o [PNP] Remove device naming based on id
o [PNP] Increment Version Number
o [PCMCIA] Fix PnP Probing in i82365.c
Alan Cox:
o [NET]: illegal --> invalid
o remove a dead EXPORT_NO_SYMBOLS
o more typo fixes
o dont assume newer cpus have the same magic registers
o more arch typo/illegal->invalid fixes
o docs for updated sk98 from vendor
o kill an old __NO_VERSION__
o re-enable SiS direct render
o console on by default if not embedded (save mucho pain)
o more typo/invalid bits
o more typo fixes and dead old code removal
o mouse and keyboard by default if not embedded
o second block illegal/invalid fixups for isdn
o keyboard controller by default if not embedded
o some isdn invalid/illegal fixups
o fix return on pms change
o more typo fixes
o sk98 vendor driver update
o more net illegal/invalid typo fixes
o further z85230 fixes
o idents for all the new skge cards
o fix pcmcia_cs without ISA
o fix invalid/illegal and printk formatting for scsi drivers
o phonedev handles this
o phonedev has an owner so this is ok too I think
o fix build of asix usb ethernet
o vga text console if x86 and not embedded
o fix invalid/illegal oddments in USB
o switch escaped 8859-1 symbols inthe kernel to ascii
o tdfx framebuffer updates
o fix binfmt_flat typos
o kill __NO_VERSION__ in intermezzo
o use invalid not illegal in reiserfs
o fix 2 byte data leak due to padding
o typo fix for time.h
o fix strncpy on generic user platforms
o maintainer for sk98
o the rest of the slab.c fix
o sunrpc doesnt need uaccess.h
o fix posix compliance for mkcompile_h script
o allow 2.6 to build on old old setups
o fix section conflict and typo in ALSA isa
o further OSS audio updates
o further sound updates
o update Changes for NFS changes
o work around tosh keyboards
o update for DC395 driver (big)
o remaining illegal/invalid/separate stuff for scsi
o ikconfig
Alan Stern:
o USB: Proper I/O buffering for the shuttle_usbat subdriver
o USB: Fix irq problem in hcd_endpoint_disable()
o USB: Rename usb_connect() to usb_choose_address()
o USB: Small fixes for usbtest
o USB: More unusual_devs.h stuff
o USB: Rename probe and unbind functions
o USB: Add functions to enable/disable endpoints, interfaces
o USB: Use the new enable/disable routines
o USB: Remove usb_set_maxpacket()
o USB: usb-storage: Move static string out of initializers.h
Alex Williamson:
o ia64: New CMC/CPE polling
o ia64: Update to CMC/CPE polling
o PCI: trivial 2.4/2.6 PCI name change/addition
Alexey Kuznetsov:
o [IPV4]: IP options were not updated while forwarding multicasts
o [PKT_SCHED]: More reasonable PSCHED_JSCALE for various values of HZ
Andi Kleen:
o x86-64 merge
o Make x86-64 compile again
Andrew Morton:
o misc fixes
o selinux merge
o re-slabify i386 pgd's and pmd's
o buffer.c debugging
o update to speedstep-centrino.c
o 3c59x suspend/resume fix
o dev_t printing
o non-MII 3c59x fix
o kwsapd can free too much memory
o unlock_buffer() needs a barrier
o Interface to invalidate regions of mmaps
o Fix vmtruncate race and distributed filesystem race
o fix bogus IO error messages
o rework readahead for congested queues
o ext3: avoid reading empty inode blocks
o Fix race in ext3_getblk
o ext3: don't start a commit in write_super()
o fix alloc_bootmem_low_pages
o soundcard.c devfs fix
o 6PACK asumes HZ=100
o devfs_lookup stack corruption fix rework
o use mark_page_accessed() in the write() path
o fix kswapd throttling
o vmscan: decaying average of zone pressure
o vmscan: use zone_pressure for page unmapping
o direct-io support for XFS unwritten extents
o Fix ipt_helper compilation
o fix select() with an xoffed tty
o fix ip_conntrack_core.h compile error
o ext3: fix commit assertion failure
o fix read_dir()
o Move the special_file() definition
o uidhash init-time locking
o com20020_cs.c doesn't compile
o pc300_drv build fix
o binfmt_script argv[0] fix
o Fix dac960 for devfs
o quota typo fix
o i810fb oops fix
o export agp_memory_reserved
o IPMI build fix
o generic HDLC updates
o dscc4 compile fix for hdlc
o serial drivers are not experimental
o ftl.c warning fix
o Watchdog: use module_param
o export install_page() to modules
o cpu_idle() startup race fix
o fix 64-bit architectures for the binprm change
o remove PF_READAHEAD
o ax8817x.c build fix for older gcc's
o dm: don't use MODULE_PARM
o dm: remove blk.h include
o dm: decimal device num sscanf
o dm: 64 bit ioctl fixes
o dm: missing #include
o [patch 7/25 dm: use sector_div()
o dm: resume() name clash
o reiserfs: fix savelinks on bigendian arches
o reiserfs: fix problem when fs is out of space
o reiserfs: fix races between link and unlink on same
o remount_fs needs lock_kernel()
o move_one_page() atomicity fix
o ide-cd error handling oops fix
o might_sleep() checks for x86 usercopy functions
o Don't trigger NMI watchdog for panic delay
o export lookup_create()
o fix free_all_bootmem_core for virtual memmap
o NMI watchdog documentation for x86-64
o Add do_setitimer prototype to linux/time.h
o itimer resolution and rounding fixes
o ext3: handle aborted journals in
o declare struct irq_desc
o mtrr race fix
o initialise page->private
Andries E. Brouwer:
o osf partition numbering
Andy Grover:
o ia64 fix for ACPI
Angelo Dell'Aera:
o [NET]: Convert tc35815.c to spinlocks
o [NET]: Trivial fix for 82596 driver
Anton Blanchard:
o ppc64: remove all request_irq calls that occur before kmalloc is
set up
o ppc64: Fix any_online_cpu for > 32 cpus, mask must be unsigned long
o ppc64: clear error_code in do_page_fault on an SLB miss
o ppc64: add div64 for 32bit boot wrapper
o ppc64: Add semtimedop
o ppc64: Add posix timers, tgkill, utimes, statfs64
o ppc64: add asm/sections.h
o ppc64: defconfig update
o [NET]: Add missing memory barriors for __LINK_STATE_RX_SCHED
handling
o ppc64: Reserve 8042 IO space on machines with no keyboard
o __initdata must not be marked const
Arnaldo Carvalho de Melo:
o wl3501: introduce iw_mgmt_info_element & associate functions and enums
o wl3501: use iw_mgmt_info_element for phy_pset (now ds_parameter_set)
o wl3501: fix set_essid wireless extension, using the flags for any
o wl3501: fix bug in iw_mgmt_info_element id field and more
o wl3501: introduce iw_mgmt_ibss_pset
o wl3501: introduce struct iw_mgmt_cf_pset
o wl3501: introduce iw_mgmt_data_rset and rate labels enum
o wl3501: implement {get,set}_scan wireless extensions
o wl3501: add a first cut, lazy scan triggering for set_scan
o MAINTAINERS: add acme as wl3501 maintainer
Arun Sharma:
o ia64: make ia32 core dumps work
o ia64: epoll support for ia32 applications
o ia64: compat_ioctl.c support
Bart De Schuymer:
o [NETFILTER]: Fix use after free of skb in nf_reinject()
o [BRIDGE]: Only build br_netfilter when INET is enabled
Bartlomiej Zolnierkiewicz:
o ide: kill no longer used CONFIG_BLK_DEV_IDE_MODES
o ide: kill no longer used CONFIG_BLK_DEV_NFORCE
o ide: kill no longer used CONFIG_BLK_DEV_PDC202XX
o ide: kill surplus menu in Kconfig
o ide: fix ordering in Kconfig
o ide: clean BLK_DEV_IDE dependencies in Kconfig
o ide: clean IDE_CHIPSETS dependencies in Kconfig
o ide: clean BLK_DEV_IDEDMA_PCI dependencies in Kconfig
o ide: use def_bool in Kconfig
o move "config SOUND" to sound/Kconfig
o do not scan partitions twice for removable devices
o fix ata_probe() driver autoloading
o ide_unregister() fixes
o fix return value for idedisk_*_max_address_* functions
o capacity related fixes
o init_idedisk_capacity() cleanup()
o fix CONFIG_IDEDISK_STROKE support in ide-disk.c
Ben Collins:
o Update IEEE1394 (r1023)
Benjamin Herrenschmidt:
o I2C: timer clean up for i2c-keywest.c
o [NET]: Do not call request_irq with spinlock held in sungem.c
o PPC32: Properly register CPUs
o PPC32: Update pmac_cpufreq driver back to working
o Fix mdelay's use of 'msec' name
Bjorn Helgaas:
o ia64: IOSAPIC .weak symbol cleanup
o ia64: more ACPI/IOSAPIC cleanup
Chas Williams:
o [ATM]: Update LANAI driver to modern PCI and DMA APIs (from
[email protected])
o [ATM]: remove EXACT_TS remove from zatm (untested)
o [ATM]: use set_current_state(x) (from [email protected])
o [ATM]: fix a typo in net/atm/Makefile (from [email protected])
o [ATM]: Convert cli() to spinlock in ZATM driver
o [ATM]: update links to new site (from <[email protected])
o [ATM]: Minor LANAI fixes from [email protected]
Chip Salzenberg:
o Require nfs-utils 1.0.5; document where to get it
Christoph Hellwig:
o [netdrvr pcmcia] remove the release timer from all pcmcia net
drivers
Daniel Ritz:
o [IPV6]: Fix memory leak in esp6_input
o [PCMCIA] don't call functions twice
Daniele Bellucci:
o USB: Audit usb_register in drivers/usb/class/audio.c
o USB: Audit usb_register() in drivers/usb/misc/emi26.c
o USB: Audit usb_register() in drivers/usb/input/wacom.c
o USB: Audit usb_register in drivers/usb/input/xpad.c
o USB: Audit usb_register() in drivers/usb/input/usbkbd.c
o USB: Audit usb_register() in drivers/usb/input/aiptek.c
o USB: Audit usb_register in usbmouse_init()
o USB: Audit usb_register() in drivers/usb/net/catc.c
o I2C: fixed a little memory leak in i2c-ali15x3.c
Danny ter Haar:
o CREDITS change
Dave Jones:
o [CPUFREQ] update Documentation
o [CPUFREQ] Fix compilation of speedstep-ich.c if SPEEDSTEP_DEBUG is
set
o [CPUFREQ] Longrun validate can fail
o [CPUFREQ] Locking fixes [1/11] First part in a series of patches
from Dominik which clean up the locking in cpufreq. It sort of
worked, but is full of races. But to keep it working at least as
well it works now, add a new spinlock cpufreq_driver_lock which
will be what cpufreq_driver_sem intended to be -- but it can indeed
be a spinlock instead of a semaphore.
o [CPUFREQ] Locking fixes [2/11] As the per-CPU initialization can
fail, we need to deal with this situation in cpufreq_remove_dev as
the sysdev core doesn't (yet) do this for us. The solution: add a
"struct cpufreq_policy
o [CPUFREQ] Fix locking [3/11] Change the return value of
cpufreq_cpu_get from a nondescriptent int to struct
cpufreq_policy*. This will allow for cleaner code - and later it
will be expected that anyone who grabs a reference by calling
cpufreq_cpu_get must return this struct cpufreq_policy* to
cpufreq_cpu_put.
o [CPUFREQ] Fix locking [4/11] Make cpufreq_remove_dev a bit more
readable. Also, assure that the GOV_STOP and the
cpufreq_driver->exit() call are indeed the last calls done.
o [CPUFREQ] Fix locking [5/11] Make cpufreq_set_policy a bit more
readable by storing the CPU's cpufreq_policy into a pointer.
o [CPUFREQ] Fix locking [6/11] Change the function parameter of
cpufreq_cpu_put to struct cpufreq_policy *.
o [CPUFREQ] Fix locking [7/11] Finally implement the two different
cpufreq_driver_target callbacks -- the one called while the per-CPU
lock is held, the other while not. While we're at it, clean up
cpufreq_governor.
o [CPUFREQ] Fix locking [8/11] Split up cpufreq_governor into a
locking and non-locking variant.
o [CPUFREQ] Fix locking [9/11] Use the per-CPU policy->lock to lock
the per-CPU "policy" data. Also, use it to serialize the setting of
new frequency policies on each CPU.
o [CPUFREQ] Fix locking [10/11] Remove the final instances of the
now-deprecated cpufreq_driver_sem. Also, the previous
"one-frequency change at one moment" limitation is gone. If it's
needed by the cpufreq driver, it should be implemented in its
cpufreq_driver->{target,setpolicy} callback.
o [CPUFREQ] Fix locking [11/11] Implement per-CPU memory allocation.
Is a bit cleaner than the previous "once and for all" approach.
o [CPUFREQ] speedstep_ICH new frequency notification fix
o [CPUFREQ] Sanity checks for voltage scaling in longhaul driver
o [AGPGART] Handle Intel chipsets whose BIOS has 'forgotten' to
assign resources
o [AGPGART] Fix Nforce modular compilation
o [CPUFREQ] Update MAINTAINERS/CREDITS Dominik doesn't want
maintainership any more (besides him still doing lots of great work
on it. 8-)
o [CPUFREQ] Sparse __user annotations for acpi driver
o [CPUFREQ] Fix sparse warnings in powernow-k7
o [CPUFREQ] sparse __user annotation for cpufreq userspace interface
o [CPUFREQ] longhaul printk cleanups
o [CPUFREQ] Better handling of revisionKey bits on Longhaul
o [CPUFREQ] Move MSRs from powernow-k7.h to include/asm-i386/msr.h
o [CPUFREQ] Remove CVS idents
o [CPUFREQ] Move rdmsrl/wrmsrl to include/asm-i386/msr.h
o [CPUFREQ] Clean up longhaul MSR usage using bitfields
o [CPUFREQ] Convert Longhaul v1 over to bitfields too
o Cset exclude:
[email protected]|ChangeSet|20030715115826|58980
o [CPUFREQ] Fix detection of Transmeta CPUs. Makes longrun work again
o [CPUFREQ] Fix compiler warnings in msr macros
o [CPUFREQ] Use standard types in wrmsrl
o [CPUFREQ] Update documentation
o [CPUFREQ] Remove deprecated email address
o Athlon Machine Check fix
Dave Kleikamp:
o JFS: Missed some non-negative error return codes
o JFS: fine-grained xattr locking
o JFS: write_super_lockfs should mark superblock clean
David Brownell:
o USB: usb audio, remove garbage warning
o USB: ehci needs a readb() on IDP425 PCI (ARM)
o USB: usbnet: zaurus c-750, motorola
o USB: ehci-hcd, TT fixup
o USB: usb_gadget.h doc fix
o USB: usb_unlink_urb() kerneldoc
o USB: ehci-hcd, show microframe schedules
o USB: ehci-hcd and period=1frame hs interrupts
o USB: usb root hubs need longer timeout
o USB: hcd initialization fix
o USB: ohci-hcd, minor d3cold resume fix
o USB: usb_new_device() updates
o USB: disable both sides of usb device ep0 at once
o USB: usbnet, prevent exotic rtnl deadlock
David Mosberger:
o ia64: Two small fixes to make ia64 build & work again
o ia64: Add forgotton <asm-ia64/sections.h>
o Many files
o ia64: Define fsid_t for kernel purposes
o xtalk.h, sn_ksyms.c, sn2_smp.c, cache.c, shuberror.c, shub.c,
iomv.c, hcl.c
o ia64: Clean up trailing whitespace
o ia64: Make elfcore32.h compile for 2.6.0-test2
o modify data types in efi.h
David S. Miller:
o [SPARC64]: Mark more things __init in kernel/pci.c
o [SPARC64]: Make sure to reject all PCI DAC dma masks
o [SPARC64]: In schizo driver, if virtual-dma property exists,
respect it
o [ATM]: Remove -g option from driver directory CFLAGS
o [NET]: Need to export secpath_dup to modules
o [SPARC64]: Use i2c/media Kconfigs instead of hardcoding
o [I2C]: ELV and VELLEMAN depend upon ISA
o [DVB]: 64-bit fixes for skystar2.c
o [DVB]: Fix pointer-->int cast in dvb_net.c
o [DVB]: Fix pointer-->int cast in budget-patch.c
o [DVB]: saa7134.h needs asm/io.h
o [MEDIA]: Fix pointer-->int cast in saa5249.c
o [MEDIA]: Make read operations return correct ssize_t in
{c-qcam,bw-qcam,w9966}.c
o [MEDIA]: Make VIDEO_PMS depend upon ISA
o [MEDIA]: Make read method return ssize_t in cpia.c
o [MEDIA]: bttvp.h needs asm/io.h
o [MEDIA]: Fix u64 printing in bttv driver
o [MEDIA]: bttv-cards.c needs linux/vmalloc.h
o [SPARC64]: Update defconfig
o [SPARC64]: Use Makefile to control dec_and_lock.o building not
in-file ifdefs
o [SCSI]: Make dc395x.c build again
o [SPARC64]: Add some more symbol debugging in register dumps
o [STRING]: Fix bug in generic strncpy() change
o [SPARC64]: Propagate bprm->interp changes to sparc 32-bit compat
layer
o [SPARC64]: More tomatillo PCI controller fixes
o [TG3]: More Sun onboard 5704 fixes
o [SPARC64]: Update defconfig
o [TG3]: Only call tg3_init_rings() after hardware has been reset
o [SPARC64]: Fix AFSR error reporting for Cheetah+/Jalapeno
o [SPARC64]: Missing cheetah+ ASI defines
David T. Hollis:
o USB: AX8817x mii/ethtool fixes among others
o USB: ax8817x.c - Fix flags to greatly increase rx performance
Eric Sandeen:
o [XFS] Use C99 initializers on sysctl structs
o [XFS] Catch read-only filesystems in xfs_setattr, and return EROFS
Felipe Damasio:
o drivers/char/stallion.c: devfs_mk_cdev fix
Fran?ois Romieu:
o fix typo in drivers/net/arcnet/com20020-isa.c
Geert Uytterhoeven:
o [IPSEC]: ipcomp.c does not neet net/esp.h
Gerd Knorr:
o v4l: sysfs'ify videodev
o v4l: bttv driver update
Greg Kroah-Hartman:
o I2C: minor cleanups to the i2c-nforce2 driver
o I2C: consolidate the i2c delay functions
o USB: fix stupid kobject coding error with regards to struct
usb_interface
o USB: core cleanups for struct usb_interface changes
o USB: changes due to struct usb_interface changing from a pointer to
an array of pointers
o USB: remove improper use of devinitdata markings for device ids
o USB: Compile AX8817x driver
o USB: AX8817x (USB ethernet) problem in 2.6.0-test1
o USB: fix bug if open() fails in usb-serial device
o USB: remove funny characters from visor driver after much prodding
o USB: bluetty: remove write_urb_pool logic, fixing locking issues
o Cset exclude: [email protected]|ChangeSet|20030730200104|44589
o USB: fix memory leak in auerswald driver
o USB: added support for TIOCM_RI and TIOCM_CD to pl2303 driver and
fix stupid bug
o PCI: pci_device_id can not be marked __devinitdata. Fixes up
sound/*
o PCI: pci_device_id can not be marked __devinitdata
o PCI: pci_device_id can not be marked __devinitdata
o PCI: pci_device_id can not be marked __devinitdata
o PCI: pci_device_id can not be marked __devinitdata
o PCI: pci_device_id can not be marked __devinitdata
o I2C: remove devinitdata marking from i2c-nforce2.c as it's wrong
o USB: fix up ALSA merge due to struct usb_interface changes
o PCI: merge fixups
o USB: remove some vendor specific stuff from the pl2303 driver to
get other devices to work
o USB: remove all struct device.name usage from the USB code
o PCI: remove all struct device.name usage from the PCI core code
o PCI: make eepro100 driver use pci_name() instead of dev.name
o USB: remove dev.name usage from gadget code
o I2C: move the name field back into the i2c_client and i2c_adapter
structures
o I2C: fix up driver model programming error
Harald Welte:
o [NETFILTER]: Use in-kernel IPSEC structures in iptables ah (by
Patrick McHardy)
o [NETFILTER]: Use in-kernel IPSEC structures in iptables esp (by
Patrick McHardy)
Herbert Xu:
o [IPSEC]: Use per-SA flag to control ECN propagation
o [IPSEC]: Fix SKB secpath refcounting
o [XFRM]: Fix OOPS in xfrm_state_update
o [XFRM_USER]: Pass correct args to xfrm_find_acq()
o [XFRM_USER]: Fix spurious NLMSG_ERROR messages
Hirofumi Ogawa:
o Fix the vfat dentry handling fix
o uses ->i_pos instead of ->i_ino on fat_fs_panic()
o Consolidate dot-stripping code
o Inline vfat_strnicmp()
o more use fat_get_short_entry()
Ian Abbott:
o USB: ftdi_sio - additional pids
o USB: ftdi_sio - VID/PID for ID TECH IDT1221U USB to RS-232 adapter
Ian Wienand:
o ia64: hardirq.h should include smp_lock.h when preempt enabled
Ivan Kokshaysky:
o alpha: pci domains update
o PCI: pci_enable_device vs bridges bugs
Jan Dittmer:
o I2C: convert via686a temp_* to milli degree celsius
Jan Kara:
o Fix old quota format locking
Jaroslav Kysela:
o ALSA update 0.9.5
o ALSA 0.9.6 update
o ALSA update
Javier Achirica:
o [wireless airo] fix Tx race
o [wireless airo] safer shutdown sequence
o [wireless airo] eliminate infinite loop
o [wireless airo] makes the card passive when entering monitor mode
o [wireless airo] adds support for noise level reporting (if
available)
o [netdrvr airo] Missing defines (only for documentation)
o [netdrvr airo] MAC type changed to unsigned
o [netdrvr airo] add missing lines for Wireless Extensions 16
o [netdrvr airo] MIC support with newer firmware
o [netdrvr airo] safer unload code
o [netdrvr airo] Fix adhoc config
Jean Tourrilhes:
o Donauboe probe fix
o IrLAP retry count
o irda-usb probe fix
o tekram-sir driver fix
Jeff Garzik:
o [netdrvr bonding] update docs
o [netdrvr bonding] fix ifenslave build on ia64
o [tokenring ibmtr_cs] fix build, due to missing ibmtr.c build
o Cset exclude: [email protected]|ChangeSet|20030731201437|53548
o intel ich5 irq router, pci ids
o [netdrvr airo] now that it builds, re-enable wireless_ext
o [irda] Add VIA FIR driver, via-ircc
Jens Axboe:
o fix broken blk_start_queue behavior
o get rid of unused request_queue field queue_wait
o AS barrier bug
o Fix bio RW_AHEAD test
o Proper block queue reference counting
o scsi_ioctl reference counting
o floppy smp fix
Jesse Barnes:
o ia64: Kconfig cleanup
o ia64: sn2 pci fixes (among others)
Jones Desougi:
o [IGMP]: linux/igmp.h needs asm/byteorder.h
Judd Montgomery:
o USB: visor.h[c] USB device IDs documentation
Kai Germaschewski:
o kbuild: Fix 'make -jN' warning
o kbuild: [PATCH] fix in-kernel genksyms for parisc symbols
o kbuild: Fix .config dependency generation
o kbuild: List deps on generated files in drivers/video/logo/Makefile
o kbuild: Add relocation information into .lst file
Kochi Takayoshi:
o ia64: Interrupt polarity fix
Linus Torvalds:
o Mark the SiS DRM driver as depending on the SiS FBCON support. It
won't even compile without it.
o Merge i830 IRQ handler cleanups from DRI CVS tree
o Update r128 drm driver from DRI CVS tree
o Fix up AGP merge: agp_memory_reserved got exported twice
o Document non-standard do_div() calling convention, since it does
not work like a C function.
o Fix up ieee1394 compile
o Make "static const" initializer to zero explicit, since truly
constant values should not end up in the BSS.
o "kernel_locked()" needs <linux/smp_lock.h>
o Fix vfsmnt leak: make autofs4 mount point expiry release the entry
that we got through the lookup_mnt().
o Don't try to signal already-zombied threads in zap_threads
o Merge with DRI CVS tree: fix use-after-free bug in DRM(takedown)
o Remove bogus temporary file from revision control
Maciej W. Rozycki:
o defxx: Maintenance + DMA API fixes
Martin Devera:
o [NET]: Fix bugs in sch_htb packet scheduler
Michael Hunold:
o Kconfig and Makefile updates
o DVB core update
o mt312 DVB frontend update
o Update MAC handling for various DVB PCI cards
o TTUSB-DEC driver update
o Hexium saa7146 driver update
Michal Sojka:
o USB: fixes for usb-skeleton.c
Miles Bader:
o Add new include files for v850
Mitchell Blank Jr.:
o PCI: Trivial DMA-mapping.txt fix
o PCI: add 2 entries to pci_ids.h
o [SPARC64]: Control debuglocks.c compilation using Makefile rules
Nathan Scott:
o [XFS] Ensure the VFS doesn't rip the inode out from beneath us when
doing unwritten extent conversion
o [XFS] Avoid doing the page->mapping->host dereferences twice on
writepage
o [XFS] Fix couple of issues in max file size calculation, print big
fs setting too
o [XFS] Cleanup empty/noaddr pagebuf initialisation; particularly for
buffers used for log IO - no longer allocate buffers for data
device then reset target, gets it right from the start
o [XFS] Max file size tweak for LBD - if LBD enabled on 32 bit
platforms slightly bigger files are possible
o [XFS] Fix the resvsp/truncate interaction problem that [email protected]
reported
o [XFS] Change any references to legal/illegal into valid/invalid -
apparently this was bad, mkaay?
o [XFS] Minor cleanups for unwritten extent fix, using one less
variable on the stack
o [XFS] Forward port 2.4 pagebuf locking to 2.5, based on Steve's
analysis - to fix the infamous pagebuf IO completion buglet
Neil Brown:
o Make sure sunrpc/cache doesn't confuse writers with readers
o Change NFSEXP_CROSSMNT to NFSEXP_CROSSMOUNT
o Remove some unused export flags and reserve a new one
o Protect against NFS requests to create symlinks bigger than one
page
o Change atomic_inc to cache_get twice
o Create a mountpoint for the nfsd filesystem
o nfsv4 page boundary handling fixes
o Fix the sunrpc cache/reader management properly
Nemosoft Unv.:
o USB: PWC 8.11
Oliver Neukum:
o USB: error return codes in usblp
o USB: cleanup of usblp (release and poll)
o USB: fix race condition in usblp_write
o USB: remove GFP_DMA from pegasus
o USB: DMA coherency issue with rtl8150
o USB: use of __devinit in st5481
o USB: dvb usb driver sleeping in interrupt
Olof Johansson:
o [RANDOM]: Fix SMP deadlock in __check_and_rekey()
Otto Solares:
o [SPARC]: Add local.h and sections.h headers
Patrick Dreker:
o I2C: add ncforce2 i2c bus driver
Patrick McHardy:
o [NETFILTER]: Fix logging of AH spis
Patrick Mochel:
o [power] Create drivers/power/
o [power] Move process suspension functions to their own file
o [power] Move saved_context_* variables
o [power] Make CONFIG_ACPI_SLEEP and CONFIG_SOFTWARE_SUSPEND
independent
o [power] Remove duplicate target
o [power] Move drivers/power/ to kernel/power/
o [power] Kill some unnessecary printk()s
o [power] Fix up refrigerator to work with ^Z-ed processes
o [power] Minor swsusp cleanups
o [power] Divorce suspend console code from swsusp
o [power] Make sure ACPI prepares a console during S3
o [power] Fix compilation when CONFIG_PM=n
o [power] Fix up compiler warnings
o [power] Remove unused function reset_videobios_after_s3()
Paul Mackerras:
o PPC32: Compile fix for arch/ppc/kernel/setup.c
o PPC32: Fix compilation when CPU_FREQ is defined
o PPC32: Make strncpy clear the unused part of the destination
o PPC32: Fix the help message for the SANDPOINT config option
Peter Chubb:
o ia64: Kill a warning if \!CONFIG_SMP
Petr Vandrovec:
o Remove write-only palette variable from matroxfb. Now it is
possible to build matroxfb without fbcon support.
o matroxfb: Initialize fbcon's cmap
o Add support for panning at vertical blanking to the matroxfb. Now
mplayer output looks much better on primary output (secondary
output is always synced with vbl).
Ralf B?chle:
o MIPS update
Randy Dunlap:
o janitor: don't init static data (arm26)
o janitor: add MODULE_LICENSE() in 2 drivers
o janitor: make serio init/exit static
o janitor: use char arrays for strings
o jantior: return -EFAULT on copy_user error
o janitor: don't init statics to 0
o don't init statics to 0 (fs/)
o janitor: convert to pci_name()
o [NET]: janitor: don't init statics to 0
o Fix incorrect umem iounmap() call
Richard Henderson:
o [ALPHA] Fix remaining pci bus conversion
o [ALPHA] Compressed kernel bootp images
o [ALPHA] Disable Wildfire, Titan, Marvel if !LEGACY_START_ADDRESS
o [ALPHA] IRQ updates to match x86 changes
o [ALPHA] Fix RTC init for LYNX
o [ALPHA] Enhanced EV6/EV7 error management
Rik van Riel:
o CREDITS update
Rob Radez:
o remove unnecessary stubs from watchdog drivers
Roland McGrath:
o spurious SIGCHLD from dying thread group leader
o fix spinlock deadlock in ptrace-reaping of detached thread
o fixes to zap_other_threads fix
Russell King:
o [ARM] Update ARM ethernet drivers
o [PCMCIA] Fix suspend for yenta_socket and i82092
o [PCMCIA] Convert cs.c and rsrc_mgr.c to use named initialisers
o [ARM] gcc 3.2.x for ARM miscompiles jffs2
o [ARM] Automatically select compiler options for ARMv5/Xscale CPUs
o [ARM] Add missing include for clps711x irq handling
o [ARM] Make PXA compile
o [ARM] Add generic sections.h for ARM
o [ARM] Fix do_settimeofday()
o [ARM] Remove old ARC and A5K machine class
o [ARM] Remove unused get_hackkit_scr prototype
o [ARM] Fix SSP IRQ handler return type
o [ARM] Update machine types file
o [ARM] Remove more static register accesses from sa1111.c
o [ARM] Fix two Acorn SCSI drivers
o [ARM] Fix platform_add_devices() prototype
o [ARM] Add asm-arm/local.h
o [netdrvr ARM] alloc_etherdev updates
o [PCMCIA] Fix cardbus init failure paths
o [PCMCIA] Disable IRQ steering and don't change the IRQ MUX register
o [PCMCIA] Report subsystem vendor/device IDs
Sam Ravnborg:
o usr: Create objectfile for usr filesystem using .incbin
o fs/Makefile: Eliminate ifneq
o bk: Ignore drivers/scsi/aic7xxx/aic7xxx_reg_print.c
o kbuild/doc: Grammatical errors corrected
o kbuild: Added CONFIG_DEBUG_INFO
o arch/um: Renamed CONFIG_DEBUGSYM to CONFIG_DEBUG_INFO
o kbuild/doc: Delete obsolete documentation files
o docbook: Added support for generating man files
o kbuild/doc: Delete instructions about running make dep
o kbuild: Let 'make help' point to README
o kbuild: Updated/moved around comments in top-level Makefile
o kbuild: Allow architectures to change CPPFLAGS
Samuel Thibault:
o [PPP]: Fix ppp_async xon/xoff handling
Sean Estabrooks:
o I2C: Additional P4B subsystem id for hidden asus smbus
Sridhar Samudrala:
o [SCTP] ADDIP basic infrastructure support. (Ardelle.Fan)
o [SCTP] Fix to avoid large kmalloc failures on 64-bit platforms
Stephen Hemminger:
o [BRIDGE]: Mailing list is at osdl.org now
o [VLAN]: Allow it to compile with VLAN_DEBUG enabled
o [VLAN]: Convert VLAN procfs stubs to no-ops
o [VLAN]: Convert over to seq_file
o [NET]: Fix rtnetlink symbol exports when INET is disabled
o [NET]: Add likely/unlikely to pskb_may_pull
o [BRIDGE]: Fix bridge notification processing
o [NET]: Convert lp486e over to dynamic allocation
o [NET] Dynamically allocate net_device structures for ROSE
o [NET] Convert ROSE to seq_file
o [NET] Fix use after free in AX.25
o [NET] Fix X.25 use after free
o [NET] X.25 async net_device fixup
Stephen Lord:
o Do not include linux/version.h, avoid massive recompilations
o Correct the maxbytes sb value for non-pagesize filesystem block
sizes, and all uses of max file size constant within XFS
o [XFS] remove extra locking which was folded into the xfs extended
attribute calls - we do not need this.
o Encapsulate the setting and clearing of PF_FSTRANS around xfs
transactions. This is used to protect against nested transactions
which can cause deadlocks. Also ensures we keep the state set for
the duration of a chain of rolling transactions.
o Add an IO completion handler to the direct_IO path to allow the
initiator to take an action at completion time. XFS uses this to
o Rework XFS read/write path so that there is one common read and one
common write path for all the different I/O variants. This means we
can now support true async I/O.
o Change XFS to support sector aligned O_DIRECT rather than
filesystem block alignment.
o [XFS] Scale default number of log buffers based on memory size
o Make the permission operation in xfs conditional on ACLs being
compiled in
o Only add bytes read into the stats if we did not get an error
o Use i_size_read and i_size_write instead of direct access to the
i_size field.
o Fix a couple of pagebuf end cases, in particular, deal with block
device which is not correctly initialized and do not submit a bio
to it - that trips a BUG.
o Move from fsid_t to __kernel_fsid_t, fixes ia64 build
o Do not include linux/version.h - no need for it
Steve French:
o lookup intents part 2
o cifs enablement for lookup intents (new 2.5 create/lookup flags)
final part
o fix create/open/lookup to use namei intent flags. Enable oplock
and packet signing
o Fix oops in cifs mkdir when server fails to return inode info after
successful mkdir
o Fix oops in cifs reopen files (restoring state after server comes
back from failure)
o Oplock flag reversed in create path
o Fix for file size handling for locally cached files
o Do not leave files created with mknod open on server. Fix related
oops. Fix timeout on open to be at least server oplock break
timeout to avoid timing out successful opens when secondary client
hung
o Fix blocksize and allocation size miscalculation
o Fix blocksize and allocation size mismatch
Theodore Y. T'so:
o Fix 32/64-bit bug in ext3
Tomas Szepe:
o [NETFILTER]: Put netfilter Kconfig options into dedicated submenu
Ville Nuorvala:
o [IPV6]: Use correct hop-limit in ip6_push_pending_frames()
Wensong Zhang:
o [IPV4] IPVS missing stats locking in estimation_timer()
o [IPV4] IPVS: sanity check of threshold setting and code tidy up
Wiktor Wodecki:
o I2C: i2c sysfs rant
Wim Van Sebroeck:
o [WATCHDOG] I810_TCO info in Kconfig
o [WATCHDOG] Cleanup of Kconfig file for the watchdog drivers
o [WATCHDOG] make wdt_pci.c independant of wdt.c
o [WATCHDOG] advantechwdt patches
Yoshinori Sato:
o h8300: config updates
o h8300: interrupt management update
o h8300: H8S architecture support
o h8300: header file updates
o h8300: arch update
o h8300: build error fixes
Please see Bugzilla for the gory details. Synopsis is that my Preario
laptop panics on boot:
Unable to handle kernel pagin request at virtual address c035800
EIP 0060:[<c014CE95>]
EIP is at store_stackinfo+0x85/0xc0
This behaviour continues since 2.5.74-bk1.
On Sat, 9 Aug 2003, Thomas Molina wrote:
> Please see Bugzilla for the gory details. Synopsis is that my Preario
> laptop panics on boot:
>
> Unable to handle kernel pagin request at virtual address c035800
>
> EIP 0060:[<c014CE95>]
> EIP is at store_stackinfo+0x85/0xc0
>
> This behaviour continues since 2.5.74-bk1.
Thanks for the update, i'll debug it during the course of the weekend.
Zwane
The following patch has been floating around forever. Can we get it in
mainstream sometime in the near future?
--- linux-2.5-tm/drivers/video/cfbimgblt.c.orig 2003-08-08 17:42:16.000000000 -0500
+++ linux-2.5-tm/drivers/video/cfbimgblt.c 2003-08-08 17:42:30.000000000 -0500
@@ -325,7 +325,7 @@
else
slow_imageblit(image, p, dst1, fgcolor, bgcolor,
start_index, pitch_index);
- } else if (image->depth == bpp)
+ } else if (image->depth <= bpp)
color_imageblit(image, p, dst1, start_index, pitch_index);
}
On Sat, Aug 09, 2003 at 11:00:57AM -0500, Thomas Molina wrote:
> The following patch has been floating around forever. Can we get it in
> mainstream sometime in the near future?
>
> --- linux-2.5-tm/drivers/video/cfbimgblt.c.orig 2003-08-08 17:42:16.000000000 -0500
> +++ linux-2.5-tm/drivers/video/cfbimgblt.c 2003-08-08 17:42:30.000000000 -0500
> @@ -325,7 +325,7 @@
> else
> slow_imageblit(image, p, dst1, fgcolor, bgcolor,
> start_index, pitch_index);
> - } else if (image->depth == bpp)
> + } else if (image->depth <= bpp)
> color_imageblit(image, p, dst1, start_index, pitch_index);
> }
>
Is this patch _still_ not in the kernel.
Linus - please merge this patch - its required for several ARM framebuffer
drivers, and several other drivers. James has indicated that this is the
correct fix back in May:
On Tue, May 13, 2003 at 11:41:34PM +0100, James Simmons wrote:
> At the very bottom of cfbimgblt.c change
>
> } else if (image->depth == bpp)
>
> to
>
> } else if (image->depth <= bpp)
>
> and tell me if this works.
--
Russell King ([email protected]) The developer of ARM Linux
http://www.arm.linux.org.uk/personal/aboutme.html
Patch somehow got out of -mm tree too. Andrew can you please apply this too ?
> The following patch has been floating around forever. Can we get it in
> mainstream sometime in the near future?
>
> --- linux-2.5-tm/drivers/video/cfbimgblt.c.orig 2003-08-08
> 17:42:16.000000000 -0500 +++
> linux-2.5-tm/drivers/video/cfbimgblt.c 2003-08-08 17:42:30.000000000 -0500
> @@ -325,7 +325,7 @@
> else
> slow_imageblit(image, p, dst1, fgcolor, bgcolor,
> start_index, pitch_index);
> - } else if (image->depth == bpp)
> + } else if (image->depth <= bpp)
> color_imageblit(image, p, dst1, start_index, pitch_index);
> }
>
>
"ismail (cartman) donmez" <[email protected]> wrote:
>
> Patch somehow got out of -mm tree too. Andrew can you please apply this too ?
> > The following patch has been floating around forever. Can we get it in
> > mainstream sometime in the near future?
> >
> > --- linux-2.5-tm/drivers/video/cfbimgblt.c.orig 2003-08-08
> > 17:42:16.000000000 -0500 +++
> > linux-2.5-tm/drivers/video/cfbimgblt.c 2003-08-08 17:42:30.000000000 -0500
> > @@ -325,7 +325,7 @@
> > else
> > slow_imageblit(image, p, dst1, fgcolor, bgcolor,
> > start_index, pitch_index);
> > - } else if (image->depth == bpp)
> > + } else if (image->depth <= bpp)
> > color_imageblit(image, p, dst1, start_index, pitch_index);
> > }
> >
> >
This change was also present in James's fbdev update, so I dropped it. But
then James's fbdev update broke so I dropped that too.
James was going to send me an updated patch. Hint. :)
Linus Torvalds wrote:
[...]
> Oliver Neukum:
> o USB: error return codes in usblp
> o USB: cleanup of usblp (release and poll)
> o USB: fix race condition in usblp_write
[...]
Well, I cannot finish printing anything now and I believe, that one of
above is responsible.
It looks as if printer gets some amount of data but then communication
'stops' and printer waits for more data (usually I have about 2cm
of page printed, paper locked and later printer error leds start
blinking happily :)
Not sure, if it's directly related, but system seems to be less
responsive later.
Version of usblp.c from 2.6.0-test2 compiled with 2.6.0-test3 does
not work as I expected (I can load module, but printer is not
detected - no usual 'usblp0: USB Unidirectional printer dev 3 if 0 alt 1
proto 2 vid 0x03F0 pid' message in logs).
I traced my problem down to -test2-bk2 (with bk1 everything works
correctly).
o Printer is connected to /dev/usb/lp0; it's HP840c
o ver_linux output: http://zeus.polsl.gliwice.pl/kernel/2.6.0-test3/ver_linux
o config: http://zeus.polsl.gliwice.pl/kernel/2.6.0-test3/config
o dmesg: http://zeus.polsl.gliwice.pl/kernel/2.6.0-test3/dmesg
o /proc/bus/usb/devices: http://zeus.polsl.gliwice.pl/kernel/2.6.0-test3/devices
o some related logs: http://zeus.polsl.gliwice.pl/kernel/2.6.0-test3/logs
Any suggestions are welcome :)
jk
--
Jacek Kawa
I wrote:
> o Printer is connected to /dev/usb/lp0; it's HP840c
> o ver_linux output: http://zeus.polsl.gliwice.pl/kernel/2.6.0-test3/ver_linux
> o config: http://zeus.polsl.gliwice.pl/kernel/2.6.0-test3/config
> o dmesg: http://zeus.polsl.gliwice.pl/kernel/2.6.0-test3/dmesg
> o /proc/bus/usb/devices: http://zeus.polsl.gliwice.pl/kernel/2.6.0-test3/devices
> o some related logs: http://zeus.polsl.gliwice.pl/kernel/2.6.0-test3/logs
aieee:
http://zeus.polsl.gliwice.pl/~jfk/kernel/2.6.0-test3/config
http://zeus.polsl.gliwice.pl/~jfk/kernel/2.6.0-test3/devices
http://zeus.polsl.gliwice.pl/~jfk/kernel/2.6.0-test3/dmesg
http://zeus.polsl.gliwice.pl/~jfk/kernel/2.6.0-test3/logs
http://zeus.polsl.gliwice.pl/~jfk/kernel/2.6.0-test3/ver_linux
and one more thing:
PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
2788 root 25 0 2096 576 1888 R 97.7 0.2 22:32.75 usb
> Any suggestions are welcome :)
Sorry!
--
Jacek Kawa
On Fri, 8 Aug 2003, Linus Torvalds wrote:
> Merging the SELinux security architecture also ends up growing the patch,
> even though it may not be all that noticeable for most normal users.
I need these patches to make it compile for m68k:
--- linux-2.6.0-test3/security/selinux/avc.c Sat Aug 9 21:43:41 2003
+++ linux-m68k-2.6.0-test3/security/selinux/avc.c Sun Aug 10 11:09:44 2003
@@ -16,6 +16,7 @@
#include <linux/slab.h>
#include <linux/fs.h>
#include <linux/dcache.h>
+#include <linux/init.h>
#include <linux/skbuff.h>
#include <net/sock.h>
#include <linux/un.h>
--- linux-2.6.0-test3/security/selinux/ss/global.h Sat Aug 9 21:43:41 2003
+++ linux-m68k-2.6.0-test3/security/selinux/ss/global.h Sun Aug 10 11:22:59 2003
@@ -7,7 +7,7 @@
#include <linux/ctype.h>
#include <linux/in.h>
#include <linux/spinlock.h>
-#include <asm/semaphore.h>
+#include <linux/sched.h>
#include "flask.h"
#include "avc.h"
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected]
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
On Fri, Aug 08, 2003 at 10:40:37PM -0700, Linus Torvalds wrote:
>...
> Summary of changes from v2.6.0-test2 to v2.6.0-test3
> ====================================================
>...
> Jens Axboe:
>...
> o Proper block queue reference counting
>...
This contains a typo that is fixed with the following patch:
--- linux-2.6.0-test3-not-full/drivers/ide/legacy/hd.c.old 2003-08-10 23:21:04.000000000 +0200
+++ linux-2.6.0-test3-not-full/drivers/ide/legacy/hd.c 2003-08-10 23:21:56.000000000 +0200
@@ -715,7 +715,7 @@
hd_queue = blk_init_queue(do_hd_request, &hd_lock);
if (!hd_queue) {
- unegister_blkdev(MAJOR_NR,"hd");
+ unregister_blkdev(MAJOR_NR,"hd");
return -ENOMEM;
}
cu
Adrian
--
"Is there not promise of rain?" Ling Tan asked suddenly out
of the darkness. There had been need of rain for many days.
"Only a promise," Lao Er said.
Pearl S. Buck - Dragon Seed
On Sat, 2003-08-09 at 17:38, Russell King wrote:
> On Sat, Aug 09, 2003 at 11:00:57AM -0500, Thomas Molina wrote:
> > The following patch has been floating around forever. Can we get it in
> > mainstream sometime in the near future?
> >
> > --- linux-2.5-tm/drivers/video/cfbimgblt.c.orig 2003-08-08 17:42:16.000000000 -0500
> > +++ linux-2.5-tm/drivers/video/cfbimgblt.c 2003-08-08 17:42:30.000000000 -0500
> > @@ -325,7 +325,7 @@
> > else
> > slow_imageblit(image, p, dst1, fgcolor, bgcolor,
> > start_index, pitch_index);
> > - } else if (image->depth == bpp)
> > + } else if (image->depth <= bpp)
> > color_imageblit(image, p, dst1, start_index, pitch_index);
> > }
> >
>
> Is this patch _still_ not in the kernel.
>
> Linus - please merge this patch - its required for several ARM framebuffer
> drivers, and several other drivers. James has indicated that this is the
> correct fix back in May:
>
Right, this fixes the 'no logo' issue - anybody have any idea why
I now have two logo's ? :)
If need be, I can give dmesg/etc/etc, but not at home right now.
> On Tue, May 13, 2003 at 11:41:34PM +0100, James Simmons wrote:
> > At the very bottom of cfbimgblt.c change
> >
> > } else if (image->depth == bpp)
> >
> > to
> >
> > } else if (image->depth <= bpp)
> >
> > and tell me if this works.
--
Martin Schlemmer
Gentoo Linux Developer, Desktop Team
Cape Town, South Africa
> Right, this fixes the 'no logo' issue - anybody have any idea why
> I now have two logo's ? :)
Do you have two CPUs ?
On Mon, 2003-08-11 at 19:25, James Simmons wrote:
> > Right, this fixes the 'no logo' issue - anybody have any idea why
> > I now have two logo's ? :)
>
> Do you have two CPUs ?
Right, this is what you get when you live in a third world country :P
Thanks,
--
Martin Schlemmer
Compile statistics: 2.6.0-test3
Compiler: gcc 3.2.2
Script: http://developer.osdl.org/~cherry/compile/compregress.sh
bzImage bzImage modules
(defconfig) (allmodconfig) (allmodconfig)
2.6.0-test3 0 warnings 7 warnings 984 warnings
0 errors 9 errors 42 errors
2.6.0-test2 0 warnings 7 warnings 1201 warnings
0 errors 9 errors 43 errors
2.6.0-test1 0 warnings 8 warnings 1319 warnings
0 errors 9 errors 38 errors
Compile statistics for 2.5 kernels and 2.6 kernels are at:
http://developer.osdl.org/~cherry/compile/
Failure summary:
drivers/block: 2 warnings, 1 errors
drivers/char: 191 warnings, 4 errors
drivers/isdn: 212 warnings, 9 errors
drivers/media: 17 warnings, 6 errors
drivers/mtd: 42 warnings, 1 errors
drivers/net: 214 warnings, 5 errors
drivers/net: 27 warnings, 5 errors
drivers/scsi/aic7xxx: 0 warnings, 1 errors
drivers/scsi: 102 warnings, 10 errors
drivers/video: 13 warnings, 3 errors
sound/oss: 51 warnings, 2 errors
sound: 2 warnings, 2 errors
Warning summary:
drivers/atm: 12 warnings, 0 errors
drivers/bluetooth: 2 warnings, 0 errors
drivers/cdrom: 26 warnings, 0 errors
drivers/i2c: 3 warnings, 0 errors
drivers/ide: 29 warnings, 0 errors
drivers/ieee1394: 1 warnings, 0 errors
drivers/md: 2 warnings, 0 errors
drivers/message: 1 warnings, 0 errors
drivers/pcmcia: 3 warnings, 0 errors
drivers/scsi/aacraid: 1 warnings, 0 errors
drivers/scsi/pcmcia: 4 warnings, 0 errors
drivers/scsi/sym53c8xx_2: 1 warnings, 0 errors
drivers/serial: 1 warnings, 0 errors
drivers/telephony: 5 warnings, 0 errors
drivers/video/aty: 3 warnings, 0 errors
drivers/video/matrox: 5 warnings, 0 errors
drivers/video/sis: 1 warnings, 0 errors
fs/afs: 1 warnings, 0 errors
fs/intermezzo: 1 warnings, 0 errors
fs/jffs: 1 warnings, 0 errors
fs/smbfs: 2 warnings, 0 errors
net: 35 warnings, 0 errors
sound/isa: 3 warnings, 0 errors
John
On Mon, Aug 11, 2003 at 04:07:08PM -0700, John Cherry wrote:
> Compile statistics: 2.6.0-test3
> Compiler: gcc 3.2.2
> Script: http://developer.osdl.org/~cherry/compile/compregress.sh
>
> bzImage bzImage modules
> (defconfig) (allmodconfig) (allmodconfig)
>
> 2.6.0-test3 0 warnings 7 warnings 984 warnings
> 2.6.0-test2 0 warnings 7 warnings 1201 warnings
^^^^
Over 200 warnings removed. Nice.
> This change was also present in James's fbdev update, so I dropped it. But
> then James's fbdev update broke so I dropped that too.
>
> James was going to send me an updated patch. Hint. :)
Here you go.
http://phoenix.infradead.org/~jsimmons/fbdev.diff.gz
Its against 2.6.0-test3.
On Mon, Aug 11, 2003 at 04:07:08PM -0700, John Cherry wrote:
> Compile statistics: 2.6.0-test3
> Compiler: gcc 3.2.2
> Script: http://developer.osdl.org/~cherry/compile/compregress.sh
>
> bzImage bzImage modules
> (defconfig) (allmodconfig) (allmodconfig)
>
> 2.6.0-test3 0 warnings 7 warnings 984 warnings
>... ^^^^^^^^^^
This number is misleading.
As a result of the "uniq" in your script the warning
include/linux/mca-legacy.h:10:2: warning: #warning "MCA legacy -
please move your driver to the new sysfs api"
that occurs in 8 different files is counted only once although this
problem is in eight different files.
> John
cu
Adrian
--
"Is there not promise of rain?" Ling Tan asked suddenly out
of the darkness. There had been need of rain for many days.
"Only a promise," Lao Er said.
Pearl S. Buck - Dragon Seed
I agree that the MCA legacy warnings are a bit misleading. Fortunately,
we don't have many multiple line warnings in the build. I'll see what I
can do to update the script for these kind of warnings.
John
On Wed, 2003-08-13 at 12:26, Adrian Bunk wrote:
> On Mon, Aug 11, 2003 at 04:07:08PM -0700, John Cherry wrote:
> > Compile statistics: 2.6.0-test3
> > Compiler: gcc 3.2.2
> > Script: http://developer.osdl.org/~cherry/compile/compregress.sh
> >
> > bzImage bzImage modules
> > (defconfig) (allmodconfig) (allmodconfig)
> >
> > 2.6.0-test3 0 warnings 7 warnings 984 warnings
> >... ^^^^^^^^^^
>
> This number is misleading.
>
> As a result of the "uniq" in your script the warning
>
> include/linux/mca-legacy.h:10:2: warning: #warning "MCA legacy -
> please move your driver to the new sysfs api"
>
> that occurs in 8 different files is counted only once although this
> problem is in eight different files.
>
> > John
>
> cu
> Adrian