This patch changes the way in which we turn off power to PCMCIA sockets.
We have traditionally relied on the socket drivers "init" method to
shut down the power to the socket by calling its own "set_socket" function.
Rather than relying on all socket drivers replicating this behaviour, we
move this into the core by calling the "set_socket" method explicitly
after we clear out the socket state structure.
One final note - there is the remote possibility that this may upset some
pcmcia/cardbus controllers which may cause the power to be left switched
on to the socket - should this happen, you should see the "*** DANGER ***"
sign appear in your kernel messages. Should this happen, I strongly
advise not plugging in your 3.3V card...
(No warranty, if you blow your hardware up you get to keep both pieces,
etc etc etc)
===== cs.c 1.63 vs edited =====
--- 1.63/drivers/pcmcia/cs.c Sun Sep 21 21:03:37 2003
+++ edited/cs.c Mon Sep 22 19:44:19 2003
@@ -450,6 +450,7 @@
s->state &= SOCKET_PRESENT|SOCKET_INUSE;
s->socket = dead_socket;
s->ops->init(s);
+ s->ops->set_socket(s, &s->socket);
s->irq.AssignedIRQ = s->irq.Config = 0;
s->lock_count = 0;
destroy_cis_cache(s);
@@ -457,15 +458,6 @@
kfree(s->fake_cis);
s->fake_cis = NULL;
}
- /* Should not the socket be forced quiet as well? e.g. turn off Vcc */
- /* Without these changes, the socket is left hot, even though card-services */
- /* realizes that no card is in place. */
- s->socket.flags &= ~SS_OUTPUT_ENA;
- s->socket.Vpp = 0;
- s->socket.Vcc = 0;
- s->socket.io_irq = 0;
- s->ops->set_socket(s, &s->socket);
- /* */
#ifdef CONFIG_CARDBUS
cb_free(s);
#endif
@@ -485,6 +477,14 @@
}
free_regions(&s->a_region);
free_regions(&s->c_region);
+
+ {
+ int status;
+ skt->ops->get_status(skt, &status);
+ if (status & SS_POWERON) {
+ printk(KERN_ERR "PCMCIA: socket %p: *** DANGER *** unable to remove socket power\n", skt);
+ }
+ }
} /* shutdown_socket */
/*======================================================================
@@ -639,6 +639,12 @@
set_current_state(TASK_UNINTERRUPTIBLE);
schedule_timeout(cs_to_timeout(vcc_settle));
+ skt->ops->get_status(skt, &status);
+ if (!(status & SS_POWERON)) {
+ pcmcia_error(skt, "unable to apply power.\n");
+ return CS_BAD_TYPE;
+ }
+
return socket_reset(skt);
}
@@ -698,6 +704,7 @@
skt->socket = dead_socket;
skt->ops->init(skt);
+ skt->ops->set_socket(skt, &skt->socket);
ret = socket_setup(skt, resume_delay);
if (ret == CS_SUCCESS) {
@@ -770,6 +777,7 @@
skt->socket = dead_socket;
skt->ops->init(skt);
+ skt->ops->set_socket(skt, &skt->socket);
/* register with the device core */
ret = class_device_register(&skt->dev);
===== hd64465_ss.c 1.16 vs edited =====
--- 1.16/drivers/pcmcia/hd64465_ss.c Sat Sep 6 22:32:53 2003
+++ edited/hd64465_ss.c Mon Sep 22 17:52:29 2003
@@ -347,11 +347,7 @@
hs_socket_t *sp = container_of(s, struct hs_socket_t, socket);
DPRINTK("hs_init(%d)\n", sp->number);
-
- sp->state.Vcc = 0;
- sp->state.Vpp = 0;
- hs_set_voltages(sp, 0, 0);
-
+
return 0;
}
===== i82092.c 1.29 vs edited =====
--- 1.29/drivers/pcmcia/i82092.c Thu Sep 11 23:46:11 2003
+++ edited/i82092.c Mon Sep 22 17:53:00 2003
@@ -426,7 +426,6 @@
enter("i82092aa_init");
mem.sys_stop = 0x0fff;
- i82092aa_set_socket(sock, &dead_socket);
for (i = 0; i < 2; i++) {
io.map = i;
i82092aa_set_io_map(sock, &io);
===== i82365.c 1.45 vs edited =====
--- 1.45/drivers/pcmcia/i82365.c Sat Sep 6 22:32:53 2003
+++ edited/i82365.c Mon Sep 22 17:53:36 2003
@@ -1322,7 +1322,6 @@
pccard_mem_map mem = { 0, 0, 0, 0, 0, 0 };
mem.sys_stop = 0x1000;
- pcic_set_socket(s, &dead_socket);
for (i = 0; i < 2; i++) {
io.map = i;
pcic_set_io_map(s, &io);
===== sa11xx_core.c 1.13 vs edited =====
--- 1.13/drivers/pcmcia/sa11xx_core.c Sat Sep 6 21:34:13 2003
+++ edited/sa11xx_core.c Mon Sep 22 17:54:15 2003
@@ -232,8 +232,6 @@
DEBUG(2, "%s(): initializing socket %u\n", __FUNCTION__, skt->nr);
skt->ops->socket_init(skt);
- sa1100_pcmcia_config_skt(skt, &dead_socket);
-
return 0;
}
===== tcic.c 1.34 vs edited =====
--- 1.34/drivers/pcmcia/tcic.c Sat Sep 6 22:32:54 2003
+++ edited/tcic.c Mon Sep 22 17:54:36 2003
@@ -865,7 +865,6 @@
pccard_mem_map mem = { 0, 0, 0, 0, 0, 0 };
mem.sys_stop = 0x1000;
- tcic_set_socket(s, &dead_socket);
for (i = 0; i < 2; i++) {
io.map = i;
tcic_set_io_map(s, &io);
--
Russell King ([email protected]) http://www.arm.linux.org.uk/personal/
Linux kernel 2.6 ARM Linux - http://www.arm.linux.org.uk/
maintainer of: 2.6 PCMCIA - http://pcmcia.arm.linux.org.uk/
2.6 Serial core
On Mon, Sep 22, 2003 at 07:58:05PM +0100, Russell King wrote:
> This patch changes the way in which we turn off power to PCMCIA sockets.
> We have traditionally relied on the socket drivers "init" method to
> shut down the power to the socket by calling its own "set_socket" function.
I've heard nothing back from this patch, so I'm going to assume that
it works for everyone, and therefore it'll be committed later today.
If anyone has any objections to it, or found that it doesn't work on
their machine, it would be preferable that they spoke up in the next
couple of hours.
--
Russell King ([email protected]) http://www.arm.linux.org.uk/personal/
Linux kernel 2.6 ARM Linux - http://www.arm.linux.org.uk/
maintainer of: 2.6 PCMCIA - http://pcmcia.arm.linux.org.uk/
2.6 Serial core