Small update, to fix a couple important 2.4-only bugs:
* SMP kernels would lock up during probing
* Hardware delays were incorrect, due to HZ=100
2.6.x kernels are not affected.
Also included is a fix for sata_via device-1 detection, which does
affect 2.6.x kernels.
BK repositories:
http://gkernel.bkbits.net/libata-2.[46]
2.4.x patch and log:
ftp://ftp.kernel.org/pub/linux/kernel/people/jgarzik/libata/2.4.26-rc1-libata3.patch.bz2
ftp://ftp.kernel.org/pub/linux/kernel/people/jgarzik/libata/2.4.26-rc1-libata3.log
2.6.x patch and log:
ftp://ftp.kernel.org/pub/linux/kernel/people/jgarzik/libata/2.6.5-rc3-libata2.patch.bz2
ftp://ftp.kernel.org/pub/linux/kernel/people/jgarzik/libata/2.6.5-rc3-libata2.log
On Wed Mar 31, 2004 at 04:02:43PM -0500, Jeff Garzik wrote:
>
> Small update, to fix a couple important 2.4-only bugs:
> * SMP kernels would lock up during probing
> * Hardware delays were incorrect, due to HZ=100
I have a Soyo P4 motherboard with built in Intel ICH5, Sil, and I have
"IDE + SATA" enabled in the bios, presumably meaning the ICH5 is in
combined mode. I usually boot with my rootfs on a ordinary IDE drive
(pata on ICH5 ide0), a cdrom (pata on ICH5 ide1) and a sata drive (sata1
on ICH5), which has all been working nicely. Many thanks. :-) Here is
what I usually see from the ICH5:
Uniform Multi-Platform E-IDE driver Revision: 7.00beta5-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH5: IDE controller at PCI slot 00:1f.1
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
hda: WDC WD2000JB-32EVA0, ATA DISK drive
hdc: SONY DVD RW DRU-510A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63, UDMA(100)
Partition check:
hda: hda1 hda2
SCSI subsystem driver Revision: 1.00
libata version 1.02 loaded.
ata_piix version 1.02
PCI: Setting latency timer of device 00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0xC000 ctl 0xC402 bmdma 0xD000 irq 18
ata2: SATA max UDMA/133 cmd 0xC800 ctl 0xCC02 bmdma 0xD008 irq 18
ata1: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4003 85:7c69 86:3e01 87:4003 88:207f
ata1: dev 0 ATA, max UDMA/133, 398297088 sectors (lba48)
ata1: dev 0 configured for UDMA/133
ata2: SATA port has no device.
ata2: thread exiting
scsi0 : ata_piix
scsi1 : ata_piix
Vendor: ATA Model: Maxtor 6Y200M0 Rev: 1.02
Type: Direct-Access ANSI SCSI revision: 05
Yesterday while doing some testing, I made a CD with the same kernel on
it as shown above, i.e. latest 2.4.26-rc1 + the current
2.4.26-rc1-libata3 patch. I then unplugged the power connector to my
usual rootfs drive (the WDC WD2000JB on ide0) to make sure I wouldn't
screw it up ;-).
Booting from CD (the SONY on ide1) with only the Maxtor 6Y200M0 (on the
ICH5 sata1), the libata driver wedged solid on bootup. After printing
ata1: SATA max UDMA/133 cmd 0xC000 ctl 0xC402 bmdma 0xD000 irq 18
ata2: SATA max UDMA/133 cmd 0xC800 ctl 0xCC02 bmdma 0xD008 irq 18
the box was dead dead dead. I can't test this setup with the bios set
to SATA only, since I don't own any SATA cdrom drives. Simply plugging
the WDC WD2000JB on ide0 back in allowed the system to boot normally.
As nearly as I can tell, one has to have a pata drive installed or the
ata_piix driver will wedge solid.
-Erik
--
Erik B. Andersen http://codepoet-consulting.com/
--This message was written using 73% post-consumer electrons--