2004-06-22 17:04:31

by Patrick Gefre

[permalink] [raw]
Subject: [PATCH 2.6] Altix serial driver

2.6 patch for our console driver. We converted the driver to use the
serial core functions. Also some changes to use sysfs/udev and a new
major number.


-- Pat

Patrick Gefre
Silicon Graphics, Inc. (E-Mail) [email protected]
2750 Blue Water Rd (Voice) (651) 683-3127
Eagan, MN 55121-1400 (FAX) (651) 683-3054


# This is a BitKeeper generated diff -Nru style patch.
#
# ChangeSet
# 2004/06/18 17:06:40-05:00 [email protected]
# Makefile:
# Remove old sn_serial console driver from makefile
#
# drivers/char/Makefile
# 2004/06/18 17:06:14-05:00 [email protected] +0 -1
# Remove old sn_serial console driver from makefile
#
diff -Nru a/drivers/char/Makefile b/drivers/char/Makefile
--- a/drivers/char/Makefile 2004-06-18 17:10:28 -05:00
+++ b/drivers/char/Makefile 2004-06-18 17:10:28 -05:00
@@ -41,7 +41,6 @@
obj-$(CONFIG_RIO) += rio/ generic_serial.o
obj-$(CONFIG_HVC_CONSOLE) += hvc_console.o
obj-$(CONFIG_RAW_DRIVER) += raw.o
-obj-$(CONFIG_SGI_L1_SERIAL) += sn_serial.o
obj-$(CONFIG_VIOCONS) += viocons.o
obj-$(CONFIG_VIOTAPE) += viotape.o

# This is a BitKeeper generated diff -Nru style patch.
#
# ChangeSet
# 2004/06/18 17:01:46-05:00 [email protected]
# Makefile:
# Adds new sn_console driver to the Makefile
# Kconfig:
# Adds new sn_console driver to Kconfig
# Remove old sn_serial driver from config
# sn_console.c:
# Implementation for new Altix console driver.
# .del-sn_serial.c~9c52f144ac55b7cb:
# Delete: drivers/char/sn_serial.c (removes old driver)
#
# drivers/serial/Makefile
# 2004/06/18 16:55:50-05:00 [email protected] +1 -0
# Adds new sn_console driver to the Makefile
#
# drivers/serial/Kconfig
# 2004/06/18 16:55:33-05:00 [email protected] +8 -1
# Adds new sn_console driver to Kconfig
#
# drivers/char/Kconfig
# 2004/06/18 16:54:35-05:00 [email protected] +0 -16
# Remove old sn_serial driver from config
#
# drivers/serial/sn_console.c
# 2004/06/18 16:32:27-05:00 [email protected] +1138 -0
#
# drivers/serial/sn_console.c
# 2004/06/18 16:32:27-05:00 [email protected] +0 -0
# BitKeeper file /data/lwork/attica3/erikj/linux-2.5-console/drivers/serial/sn_console.c
#
# BitKeeper/deleted/.del-sn_serial.c~9c52f144ac55b7cb
# 2004/06/18 16:27:08-05:00 [email protected] +0 -0
# Delete: drivers/char/sn_serial.c
#
diff -Nru a/drivers/char/Kconfig b/drivers/char/Kconfig
--- a/drivers/char/Kconfig 2004-06-18 17:16:46 -05:00
+++ b/drivers/char/Kconfig 2004-06-18 17:16:46 -05:00
@@ -371,22 +371,6 @@
If you have an Alchemy AU1000 processor (MIPS based) and you want
to use serial ports, say Y. Otherwise, say N.

-config SGI_L1_SERIAL
- bool "SGI Altix L1 serial support"
- depends on SERIAL_NONSTANDARD && IA64
- help
- If you have an SGI Altix and you want to use the serial port
- connected to the system controller (you want this!), say Y.
- Otherwise, say N.
-
-config SGI_L1_SERIAL_CONSOLE
- bool "SGI Altix L1 serial console support"
- depends on SGI_L1_SERIAL
- help
- If you have an SGI Altix and you would like to use the system
- controller serial port as your console (you want this!),
- say Y. Otherwise, say N.
-
config AU1000_SERIAL_CONSOLE
bool "Enable Au1000 serial console"
depends on AU1000_UART
diff -Nru a/drivers/char/sn_serial.c b/drivers/char/sn_serial.c
--- a/drivers/char/sn_serial.c 2004-06-18 17:16:46 -05:00
+++ /dev/null Wed Dec 31 16:00:00 196900
@@ -1,1028 +0,0 @@
-/*
- * C-Brick Serial Port (and console) driver for SGI Altix machines.
- *
- * This driver is NOT suitable for talking to the l1-controller for
- * anything other than 'console activities' --- please use the l1
- * driver for that.
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 2003 Silicon Graphics, Inc. All rights reserved.
- */
-
-#include <linux/config.h>
-#include <linux/interrupt.h>
-#include <linux/tty.h>
-#include <linux/serial.h>
-#include <linux/console.h>
-#include <linux/module.h>
-#include <linux/sysrq.h>
-#include <linux/circ_buf.h>
-#include <linux/serial_reg.h>
-#include <asm/uaccess.h>
-#include <asm/sn/sgi.h>
-#include <asm/sn/sn_sal.h>
-#include <asm/sn/pci/pciio.h>
-#include <asm/sn/simulator.h>
-#include <asm/sn/sn2/sn_private.h>
-
-#if defined(CONFIG_SGI_L1_SERIAL_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
-static char sysrq_serial_str[] = "\eSYS";
-static char *sysrq_serial_ptr = sysrq_serial_str;
-static unsigned long sysrq_requested;
-#endif /* CONFIG_SGI_L1_SERIAL_CONSOLE && CONFIG_MAGIC_SYSRQ */
-
-/* minor device number */
-#define SN_SAL_MINOR 64
-
-/* number of characters left in xmit buffer before we ask for more */
-#define WAKEUP_CHARS 128
-
-/* number of characters we can transmit to the SAL console at a time */
-#define SN_SAL_MAX_CHARS 120
-
-#define SN_SAL_EVENT_WRITE_WAKEUP 0
-
-/* 64K, when we're asynch, it must be at least printk's LOG_BUF_LEN to
- * avoid losing chars, (always has to be a power of 2) */
-#define SN_SAL_BUFFER_SIZE (64 * (1 << 10))
-
-#define SN_SAL_UART_FIFO_DEPTH 16
-#define SN_SAL_UART_FIFO_SPEED_CPS 9600/10
-
-/* we don't kmalloc/get_free_page these as we want them available
- * before either of those are initialized */
-static char sn_xmit_buff_mem[SN_SAL_BUFFER_SIZE];
-
-struct volatile_circ_buf {
- char *cb_buf;
- int cb_head;
- int cb_tail;
-};
-
-static struct volatile_circ_buf xmit = { .cb_buf = sn_xmit_buff_mem };
-static char sn_tmp_buffer[SN_SAL_BUFFER_SIZE];
-
-static struct tty_struct *sn_sal_tty;
-
-static struct timer_list sn_sal_timer;
-static int sn_sal_event; /* event type for task queue */
-
-static int sn_sal_is_asynch;
-static int sn_sal_irq;
-static spinlock_t sn_sal_lock = SPIN_LOCK_UNLOCKED;
-static int sn_total_tx_count;
-static int sn_total_rx_count;
-
-static void sn_sal_tasklet_action(unsigned long data);
-static DECLARE_TASKLET(sn_sal_tasklet, sn_sal_tasklet_action, 0);
-
-static unsigned long sn_interrupt_timeout;
-
-extern u64 master_node_bedrock_address;
-
-#undef DEBUG
-#ifdef DEBUG
-static int sn_debug_printf(const char *fmt, ...);
-#define DPRINTF(x...) sn_debug_printf(x)
-#else
-#define DPRINTF(x...) do { } while (0)
-#endif
-
-struct sn_sal_ops {
- int (*sal_puts)(const char *s, int len);
- int (*sal_getc)(void);
- int (*sal_input_pending)(void);
- void (*sal_wakeup_transmit)(void);
-};
-
-/* This is the pointer used. It is assigned to point to one of
- * the tables below.
- */
-static struct sn_sal_ops *sn_func;
-
-/* Prototypes */
-static int snt_hw_puts(const char *, int);
-static int snt_poll_getc(void);
-static int snt_poll_input_pending(void);
-static int snt_sim_puts(const char *, int);
-static int snt_sim_getc(void);
-static int snt_sim_input_pending(void);
-static int snt_intr_getc(void);
-static int snt_intr_input_pending(void);
-static void sn_intr_transmit_chars(void);
-
-/* A table for polling */
-static struct sn_sal_ops poll_ops = {
- .sal_puts = snt_hw_puts,
- .sal_getc = snt_poll_getc,
- .sal_input_pending = snt_poll_input_pending
-};
-
-/* A table for the simulator */
-static struct sn_sal_ops sim_ops = {
- .sal_puts = snt_sim_puts,
- .sal_getc = snt_sim_getc,
- .sal_input_pending = snt_sim_input_pending
-};
-
-/* A table for interrupts enabled */
-static struct sn_sal_ops intr_ops = {
- .sal_puts = snt_hw_puts,
- .sal_getc = snt_intr_getc,
- .sal_input_pending = snt_intr_input_pending,
- .sal_wakeup_transmit = sn_intr_transmit_chars
-};
-
-
-/* the console does output in two distinctly different ways:
- * synchronous and asynchronous (buffered). initally, early_printk
- * does synchronous output. any data written goes directly to the SAL
- * to be output (incidentally, it is internally buffered by the SAL)
- * after interrupts and timers are initialized and available for use,
- * the console init code switches to asynchronous output. this is
- * also the earliest opportunity to begin polling for console input.
- * after console initialization, console output and tty (serial port)
- * output is buffered and sent to the SAL asynchronously (either by
- * timer callback or by UART interrupt) */
-
-
-/* routines for running the console in polling mode */
-
-static int
-snt_hw_puts(const char *s, int len)
-{
- /* looking at the PROM source code, putb calls the flush
- * routine, so if we send characters in FIFO sized chunks, it
- * should go out by the next time the timer gets called */
- return ia64_sn_console_putb(s, len);
-}
-
-static int
-snt_poll_getc(void)
-{
- int ch;
- ia64_sn_console_getc(&ch);
- return ch;
-}
-
-static int
-snt_poll_input_pending(void)
-{
- int status, input;
-
- status = ia64_sn_console_check(&input);
- return !status && input;
-}
-
-
-/* routines for running the console on the simulator */
-
-static int
-snt_sim_puts(const char *str, int count)
-{
- int counter = count;
-
-#ifdef FLAG_DIRECT_CONSOLE_WRITES
- /* This is an easy way to pre-pend the output to know whether the output
- * was done via sal or directly */
- writeb('[', master_node_bedrock_address + (UART_TX << 3));
- writeb('+', master_node_bedrock_address + (UART_TX << 3));
- writeb(']', master_node_bedrock_address + (UART_TX << 3));
- writeb(' ', master_node_bedrock_address + (UART_TX << 3));
-#endif /* FLAG_DIRECT_CONSOLE_WRITES */
- while (counter > 0) {
- writeb(*str, master_node_bedrock_address + (UART_TX << 3));
- counter--;
- str++;
- }
-
- return count;
-}
-
-static int
-snt_sim_getc(void)
-{
- return readb(master_node_bedrock_address + (UART_RX << 3));
-}
-
-static int
-snt_sim_input_pending(void)
-{
- return readb(master_node_bedrock_address + (UART_LSR << 3)) & UART_LSR_DR;
-}
-
-
-/* routines for an interrupt driven console (normal) */
-
-static int
-snt_intr_getc(void)
-{
- return ia64_sn_console_readc();
-}
-
-static int
-snt_intr_input_pending(void)
-{
- return ia64_sn_console_intr_status() & SAL_CONSOLE_INTR_RECV;
-}
-
-/* The early printk (possible setup) and function call */
-
-void
-early_printk_sn_sal(const char *s, unsigned count)
-{
- extern void early_sn_setup(void);
-
- if (!sn_func) {
- if (IS_RUNNING_ON_SIMULATOR())
- sn_func = &sim_ops;
- else
- sn_func = &poll_ops;
-
- early_sn_setup();
- }
- sn_func->sal_puts(s, count);
-}
-
-#ifdef DEBUG
-/* this is as "close to the metal" as we can get, used when the driver
- * itself may be broken */
-static int
-sn_debug_printf(const char *fmt, ...)
-{
- static char printk_buf[1024];
- int printed_len;
- va_list args;
-
- va_start(args, fmt);
- printed_len = vscnprintf(printk_buf, sizeof(printk_buf), fmt, args);
- early_printk_sn_sal(printk_buf, printed_len);
- va_end(args);
- return printed_len;
-}
-#endif /* DEBUG */
-
-/*
- * Interrupt handling routines.
- */
-
-static void
-sn_sal_sched_event(int event)
-{
- sn_sal_event |= (1 << event);
- tasklet_schedule(&sn_sal_tasklet);
-}
-
-/* sn_receive_chars can be called before sn_sal_tty is initialized. in
- * that case, its only use is to trigger sysrq and kdb */
-static void
-sn_receive_chars(struct pt_regs *regs, unsigned long *flags)
-{
- int ch;
-
- while (sn_func->sal_input_pending()) {
- ch = sn_func->sal_getc();
- if (ch < 0) {
- printk(KERN_ERR "sn_serial: An error occured while "
- "obtaining data from the console (0x%0x)\n", ch);
- break;
- }
-#if defined(CONFIG_SGI_L1_SERIAL_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
- if (sysrq_requested) {
- unsigned long sysrq_timeout = sysrq_requested + HZ*5;
-
- sysrq_requested = 0;
- if (ch && time_before(jiffies, sysrq_timeout)) {
- spin_unlock_irqrestore(&sn_sal_lock, *flags);
- handle_sysrq(ch, regs, NULL);
- spin_lock_irqsave(&sn_sal_lock, *flags);
- /* don't record this char */
- continue;
- }
- }
- if (ch == *sysrq_serial_ptr) {
- if (!(*++sysrq_serial_ptr)) {
- sysrq_requested = jiffies;
- sysrq_serial_ptr = sysrq_serial_str;
- }
- }
- else
- sysrq_serial_ptr = sysrq_serial_str;
-#endif /* CONFIG_SGI_L1_SERIAL_CONSOLE && CONFIG_MAGIC_SYSRQ */
-
- /* record the character to pass up to the tty layer */
- if (sn_sal_tty) {
- *sn_sal_tty->flip.char_buf_ptr = ch;
- sn_sal_tty->flip.char_buf_ptr++;
- sn_sal_tty->flip.count++;
- if (sn_sal_tty->flip.count == TTY_FLIPBUF_SIZE)
- break;
- }
- sn_total_rx_count++;
- }
-
- if (sn_sal_tty)
- tty_flip_buffer_push((struct tty_struct *)sn_sal_tty);
-}
-
-
-/* synch_flush_xmit must be called with sn_sal_lock */
-static void
-synch_flush_xmit(void)
-{
- int xmit_count, tail, head, loops, ii;
- int result;
- char *start;
-
- if (xmit.cb_head == xmit.cb_tail)
- return; /* Nothing to do. */
-
- head = xmit.cb_head;
- tail = xmit.cb_tail;
- start = &xmit.cb_buf[tail];
-
- /* twice around gets the tail to the end of the buffer and
- * then to the head, if needed */
- loops = (head < tail) ? 2 : 1;
-
- for (ii = 0; ii < loops; ii++) {
- xmit_count = (head < tail) ? (SN_SAL_BUFFER_SIZE - tail) : (head - tail);
-
- if (xmit_count > 0) {
- result = sn_func->sal_puts((char *)start, xmit_count);
- if (!result)
- DPRINTF("\n*** synch_flush_xmit failed to flush\n");
- if (result > 0) {
- xmit_count -= result;
- sn_total_tx_count += result;
- tail += result;
- tail &= SN_SAL_BUFFER_SIZE - 1;
- xmit.cb_tail = tail;
- start = (char *)&xmit.cb_buf[tail];
- }
- }
- }
-}
-
-/* must be called with a lock protecting the circular buffer and
- * sn_sal_tty */
-static void
-sn_poll_transmit_chars(void)
-{
- int xmit_count, tail, head;
- int result;
- char *start;
-
- BUG_ON(!sn_sal_is_asynch);
-
- if (xmit.cb_head == xmit.cb_tail ||
- (sn_sal_tty && (sn_sal_tty->stopped || sn_sal_tty->hw_stopped))) {
- /* Nothing to do. */
- return;
- }
-
- head = xmit.cb_head;
- tail = xmit.cb_tail;
- start = &xmit.cb_buf[tail];
-
- xmit_count = (head < tail) ? (SN_SAL_BUFFER_SIZE - tail) : (head - tail);
-
- if (xmit_count == 0)
- DPRINTF("\n*** empty xmit_count\n");
-
- /* use the ops, as we could be on the simulator */
- result = sn_func->sal_puts((char *)start, xmit_count);
- if (!result)
- DPRINTF("\n*** error in synchronous sal_puts\n");
- /* XXX chadt clean this up */
- if (result > 0) {
- xmit_count -= result;
- sn_total_tx_count += result;
- tail += result;
- tail &= SN_SAL_BUFFER_SIZE - 1;
- xmit.cb_tail = tail;
- start = &xmit.cb_buf[tail];
- }
-
- /* if there's few enough characters left in the xmit buffer
- * that we could stand for the upper layer to send us some
- * more, ask for it. */
- if (sn_sal_tty)
- if (CIRC_CNT(xmit.cb_head, xmit.cb_tail, SN_SAL_BUFFER_SIZE) < WAKEUP_CHARS)
- sn_sal_sched_event(SN_SAL_EVENT_WRITE_WAKEUP);
-}
-
-
-/* must be called with a lock protecting the circular buffer and
- * sn_sal_tty */
-static void
-sn_intr_transmit_chars(void)
-{
- int xmit_count, tail, head, loops, ii;
- int result;
- char *start;
-
- BUG_ON(!sn_sal_is_asynch);
-
- if (xmit.cb_head == xmit.cb_tail ||
- (sn_sal_tty && (sn_sal_tty->stopped || sn_sal_tty->hw_stopped))) {
- /* Nothing to do. */
- return;
- }
-
- head = xmit.cb_head;
- tail = xmit.cb_tail;
- start = &xmit.cb_buf[tail];
-
- /* twice around gets the tail to the end of the buffer and
- * then to the head, if needed */
- loops = (head < tail) ? 2 : 1;
-
- for (ii = 0; ii < loops; ii++) {
- xmit_count = (head < tail) ?
- (SN_SAL_BUFFER_SIZE - tail) : (head - tail);
-
- if (xmit_count > 0) {
- result = ia64_sn_console_xmit_chars((char *)start, xmit_count);
-#ifdef DEBUG
- if (!result)
- DPRINTF("`");
-#endif
- if (result > 0) {
- xmit_count -= result;
- sn_total_tx_count += result;
- tail += result;
- tail &= SN_SAL_BUFFER_SIZE - 1;
- xmit.cb_tail = tail;
- start = &xmit.cb_buf[tail];
- }
- }
- }
-
- /* if there's few enough characters left in the xmit buffer
- * that we could stand for the upper layer to send us some
- * more, ask for it. */
- if (sn_sal_tty)
- if (CIRC_CNT(xmit.cb_head, xmit.cb_tail, SN_SAL_BUFFER_SIZE) < WAKEUP_CHARS)
- sn_sal_sched_event(SN_SAL_EVENT_WRITE_WAKEUP);
-}
-
-
-static irqreturn_t
-sn_sal_interrupt(int irq, void *dev_id, struct pt_regs *regs)
-{
- /* this call is necessary to pass the interrupt back to the
- * SAL, since it doesn't intercept the UART interrupts
- * itself */
- int status = ia64_sn_console_intr_status();
- unsigned long flags;
-
- spin_lock_irqsave(&sn_sal_lock, flags);
- if (status & SAL_CONSOLE_INTR_RECV)
- sn_receive_chars(regs, &flags);
- if (status & SAL_CONSOLE_INTR_XMIT)
- sn_intr_transmit_chars();
- spin_unlock_irqrestore(&sn_sal_lock, flags);
- return IRQ_HANDLED;
-}
-
-
-/* returns the console irq if interrupt is successfully registered,
- * else 0 */
-static int
-sn_sal_connect_interrupt(void)
-{
- cpuid_t intr_cpuid;
- unsigned int intr_cpuloc;
- nasid_t console_nasid;
- unsigned int console_irq;
- int result;
-
- console_nasid = ia64_sn_get_console_nasid();
- intr_cpuid = first_cpu(node_to_cpumask(nasid_to_cnodeid(console_nasid)));
- intr_cpuloc = cpu_physical_id(intr_cpuid);
- console_irq = CPU_VECTOR_TO_IRQ(intr_cpuloc, SGI_UART_VECTOR);
-
- result = intr_connect_level(intr_cpuid, SGI_UART_VECTOR);
- BUG_ON(result != SGI_UART_VECTOR);
-
- result = request_irq(console_irq, sn_sal_interrupt, SA_INTERRUPT, "SAL console driver", &sn_sal_tty);
- if (result >= 0)
- return console_irq;
-
- printk(KERN_WARNING "sn_serial: console proceeding in polled mode\n");
- return 0;
-}
-
-static void
-sn_sal_tasklet_action(unsigned long data)
-{
- unsigned long flags;
-
- if (sn_sal_tty) {
- spin_lock_irqsave(&sn_sal_lock, flags);
- if (sn_sal_tty) {
- if (test_and_clear_bit(SN_SAL_EVENT_WRITE_WAKEUP, &sn_sal_event)) {
- if ((sn_sal_tty->flags & (1 << TTY_DO_WRITE_WAKEUP)) && sn_sal_tty->ldisc.write_wakeup)
- (sn_sal_tty->ldisc.write_wakeup)((struct tty_struct *)sn_sal_tty);
- wake_up_interruptible((wait_queue_head_t *)&sn_sal_tty->write_wait);
- }
- }
- spin_unlock_irqrestore(&sn_sal_lock, flags);
- }
-}
-
-
-/*
- * This function handles polled mode.
- */
-static void
-sn_sal_timer_poll(unsigned long dummy)
-{
- unsigned long flags;
-
- if (!sn_sal_irq) {
- spin_lock_irqsave(&sn_sal_lock, flags);
- sn_receive_chars(NULL, &flags);
- sn_poll_transmit_chars();
- spin_unlock_irqrestore(&sn_sal_lock, flags);
- mod_timer(&sn_sal_timer, jiffies + sn_interrupt_timeout);
- }
-}
-
-
-/*
- * User-level console routines
- */
-
-static int
-sn_sal_open(struct tty_struct *tty, struct file *filp)
-{
- unsigned long flags;
-
- DPRINTF("sn_sal_open: sn_sal_tty = %p, tty = %p, filp = %p\n",
- sn_sal_tty, tty, filp);
-
- spin_lock_irqsave(&sn_sal_lock, flags);
- if (!sn_sal_tty)
- sn_sal_tty = tty;
- spin_unlock_irqrestore(&sn_sal_lock, flags);
-
- return 0;
-}
-
-
-/* We're keeping all our resources. We're keeping interrupts turned
- * on. Maybe just let the tty layer finish its stuff...? GMSH
- */
-static void
-sn_sal_close(struct tty_struct *tty, struct file * filp)
-{
- if (tty->count == 1) {
- unsigned long flags;
- tty->closing = 1;
- if (tty->driver->flush_buffer)
- tty->driver->flush_buffer(tty);
- if (tty->ldisc.flush_buffer)
- tty->ldisc.flush_buffer(tty);
- tty->closing = 0;
- spin_lock_irqsave(&sn_sal_lock, flags);
- sn_sal_tty = NULL;
- spin_unlock_irqrestore(&sn_sal_lock, flags);
- }
-}
-
-
-static int
-sn_sal_write(struct tty_struct *tty, int from_user,
- const unsigned char *buf, int count)
-{
- int c, ret = 0;
- unsigned long flags;
-
- if (from_user) {
- while (1) {
- int c1;
- c = CIRC_SPACE_TO_END(xmit.cb_head, xmit.cb_tail,
- SN_SAL_BUFFER_SIZE);
-
- if (count < c)
- c = count;
- if (c <= 0)
- break;
-
- c -= copy_from_user(sn_tmp_buffer, buf, c);
- if (!c) {
- if (!ret)
- ret = -EFAULT;
- break;
- }
-
- /* Turn off interrupts and see if the xmit buffer has
- * moved since the last time we looked.
- */
- spin_lock_irqsave(&sn_sal_lock, flags);
- c1 = CIRC_SPACE_TO_END(xmit.cb_head, xmit.cb_tail, SN_SAL_BUFFER_SIZE);
-
- if (c1 < c)
- c = c1;
-
- memcpy(xmit.cb_buf + xmit.cb_head, sn_tmp_buffer, c);
- xmit.cb_head = ((xmit.cb_head + c) & (SN_SAL_BUFFER_SIZE - 1));
- spin_unlock_irqrestore(&sn_sal_lock, flags);
-
- buf += c;
- count -= c;
- ret += c;
- }
- }
- else {
- /* The buffer passed in isn't coming from userland,
- * so cut out the middleman (sn_tmp_buffer).
- */
- spin_lock_irqsave(&sn_sal_lock, flags);
- while (1) {
- c = CIRC_SPACE_TO_END(xmit.cb_head, xmit.cb_tail, SN_SAL_BUFFER_SIZE);
-
- if (count < c)
- c = count;
- if (c <= 0) {
- break;
- }
- memcpy(xmit.cb_buf + xmit.cb_head, buf, c);
- xmit.cb_head = ((xmit.cb_head + c) & (SN_SAL_BUFFER_SIZE - 1));
- buf += c;
- count -= c;
- ret += c;
- }
- spin_unlock_irqrestore(&sn_sal_lock, flags);
- }
-
- spin_lock_irqsave(&sn_sal_lock, flags);
- if (xmit.cb_head != xmit.cb_tail && !(tty && (tty->stopped || tty->hw_stopped)))
- if (sn_func->sal_wakeup_transmit)
- sn_func->sal_wakeup_transmit();
- spin_unlock_irqrestore(&sn_sal_lock, flags);
-
- return ret;
-}
-
-
-static void
-sn_sal_put_char(struct tty_struct *tty, unsigned char ch)
-{
- unsigned long flags;
-
- spin_lock_irqsave(&sn_sal_lock, flags);
- if (CIRC_SPACE(xmit.cb_head, xmit.cb_tail, SN_SAL_BUFFER_SIZE) != 0) {
- xmit.cb_buf[xmit.cb_head] = ch;
- xmit.cb_head = (xmit.cb_head + 1) & (SN_SAL_BUFFER_SIZE-1);
- if ( sn_func->sal_wakeup_transmit )
- sn_func->sal_wakeup_transmit();
- }
- spin_unlock_irqrestore(&sn_sal_lock, flags);
-}
-
-
-static void
-sn_sal_flush_chars(struct tty_struct *tty)
-{
- unsigned long flags;
-
- spin_lock_irqsave(&sn_sal_lock, flags);
- if (CIRC_CNT(xmit.cb_head, xmit.cb_tail, SN_SAL_BUFFER_SIZE))
- if (sn_func->sal_wakeup_transmit)
- sn_func->sal_wakeup_transmit();
- spin_unlock_irqrestore(&sn_sal_lock, flags);
-}
-
-
-static int
-sn_sal_write_room(struct tty_struct *tty)
-{
- unsigned long flags;
- int space;
-
- spin_lock_irqsave(&sn_sal_lock, flags);
- space = CIRC_SPACE(xmit.cb_head, xmit.cb_tail, SN_SAL_BUFFER_SIZE);
- spin_unlock_irqrestore(&sn_sal_lock, flags);
- return space;
-}
-
-
-static int
-sn_sal_chars_in_buffer(struct tty_struct *tty)
-{
- unsigned long flags;
- int space;
-
- spin_lock_irqsave(&sn_sal_lock, flags);
- space = CIRC_CNT(xmit.cb_head, xmit.cb_tail, SN_SAL_BUFFER_SIZE);
- DPRINTF("<%d>", space);
- spin_unlock_irqrestore(&sn_sal_lock, flags);
- return space;
-}
-
-
-static void
-sn_sal_flush_buffer(struct tty_struct *tty)
-{
- unsigned long flags;
-
- /* drop everything */
- spin_lock_irqsave(&sn_sal_lock, flags);
- xmit.cb_head = xmit.cb_tail = 0;
- spin_unlock_irqrestore(&sn_sal_lock, flags);
-
- /* wake up tty level */
- wake_up_interruptible(&tty->write_wait);
- if ((tty->flags & (1 << TTY_DO_WRITE_WAKEUP)) && tty->ldisc.write_wakeup)
- (tty->ldisc.write_wakeup)(tty);
-}
-
-
-static void
-sn_sal_hangup(struct tty_struct *tty)
-{
- sn_sal_flush_buffer(tty);
-}
-
-
-static void
-sn_sal_wait_until_sent(struct tty_struct *tty, int timeout)
-{
- /* this is SAL's problem */
- DPRINTF("<sn_serial: should wait until sent>");
-}
-
-
-/*
- * sn_sal_read_proc
- *
- * Console /proc interface
- */
-
-static int
-sn_sal_read_proc(char *page, char **start, off_t off, int count,
- int *eof, void *data)
-{
- int len = 0;
- off_t begin = 0;
-
- len += sprintf(page, "sn_serial: nasid:%ld irq:%d tx:%d rx:%d\n",
- ia64_sn_get_console_nasid(), sn_sal_irq,
- sn_total_tx_count, sn_total_rx_count);
- *eof = 1;
-
- if (off >= len+begin)
- return 0;
- *start = page + (off-begin);
-
- return count < begin+len-off ? count : begin+len-off;
-}
-
-
-static struct tty_operations sn_sal_driver_ops = {
- .open = sn_sal_open,
- .close = sn_sal_close,
- .write = sn_sal_write,
- .put_char = sn_sal_put_char,
- .flush_chars = sn_sal_flush_chars,
- .write_room = sn_sal_write_room,
- .chars_in_buffer = sn_sal_chars_in_buffer,
- .hangup = sn_sal_hangup,
- .wait_until_sent = sn_sal_wait_until_sent,
- .read_proc = sn_sal_read_proc,
-};
-static struct tty_driver *sn_sal_driver;
-
-/* sn_sal_init wishlist:
- * - allocate sn_tmp_buffer
- * - fix up the tty_driver struct
- * - turn on receive interrupts
- * - do any termios twiddling once and for all
- */
-
-/*
- * Boot-time initialization code
- */
-
-static void __init
-sn_sal_switch_to_asynch(void)
-{
- unsigned long flags;
-
- /* without early_printk, we may be invoked late enough to race
- * with other cpus doing console IO at this point, however
- * console interrupts will never be enabled */
- spin_lock_irqsave(&sn_sal_lock, flags);
-
- if (sn_sal_is_asynch) {
- spin_unlock_irqrestore(&sn_sal_lock, flags);
- return;
- }
-
- DPRINTF("sn_serial: switch to asynchronous console\n");
-
- /* early_printk invocation may have done this for us */
- if (!sn_func) {
- if (IS_RUNNING_ON_SIMULATOR())
- sn_func = &sim_ops;
- else
- sn_func = &poll_ops;
- }
-
- /* we can't turn on the console interrupt (as request_irq
- * calls kmalloc, which isn't set up yet), so we rely on a
- * timer to poll for input and push data from the console
- * buffer.
- */
- init_timer(&sn_sal_timer);
- sn_sal_timer.function = sn_sal_timer_poll;
-
- if (IS_RUNNING_ON_SIMULATOR())
- sn_interrupt_timeout = 6;
- else {
- /* 960cps / 16 char FIFO = 60HZ
- * HZ / (SN_SAL_FIFO_SPEED_CPS / SN_SAL_FIFO_DEPTH) */
- sn_interrupt_timeout = HZ * SN_SAL_UART_FIFO_DEPTH / SN_SAL_UART_FIFO_SPEED_CPS;
- }
- mod_timer(&sn_sal_timer, jiffies + sn_interrupt_timeout);
-
- sn_sal_is_asynch = 1;
- spin_unlock_irqrestore(&sn_sal_lock, flags);
-}
-
-static void __init
-sn_sal_switch_to_interrupts(void)
-{
- int irq;
-
- DPRINTF("sn_serial: switching to interrupt driven console\n");
-
- irq = sn_sal_connect_interrupt();
- if (irq) {
- unsigned long flags;
- spin_lock_irqsave(&sn_sal_lock, flags);
-
- /* sn_sal_irq is a global variable. When it's set to
- * a non-zero value, we stop polling for input (since
- * interrupts should now be enabled). */
- sn_sal_irq = irq;
- sn_func = &intr_ops;
-
- /* turn on receive interrupts */
- ia64_sn_console_intr_enable(SAL_CONSOLE_INTR_RECV);
- spin_unlock_irqrestore(&sn_sal_lock, flags);
- }
-}
-
-static int __init
-sn_sal_module_init(void)
-{
- int retval;
-
- DPRINTF("sn_serial: sn_sal_module_init\n");
-
- if (!ia64_platform_is("sn2"))
- return -ENODEV;
-
- sn_sal_driver = alloc_tty_driver(1);
- if ( !sn_sal_driver )
- return -ENOMEM;
-
- sn_sal_driver->owner = THIS_MODULE;
- sn_sal_driver->driver_name = "sn_serial";
- sn_sal_driver->name = "ttyS";
- sn_sal_driver->major = TTY_MAJOR;
- sn_sal_driver->minor_start = SN_SAL_MINOR;
- sn_sal_driver->type = TTY_DRIVER_TYPE_SERIAL;
- sn_sal_driver->subtype = SERIAL_TYPE_NORMAL;
- sn_sal_driver->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_NO_DEVFS;
-
- tty_set_operations(sn_sal_driver, &sn_sal_driver_ops);
-
- /* when this driver is compiled in, the console initialization
- * will have already switched us into asynchronous operation
- * before we get here through the module initcalls */
- sn_sal_switch_to_asynch();
-
- /* at this point (module_init) we can try to turn on interrupts */
- if (!IS_RUNNING_ON_SIMULATOR())
- sn_sal_switch_to_interrupts();
-
- sn_sal_driver->init_termios = tty_std_termios;
- sn_sal_driver->init_termios.c_cflag = B9600 | CS8 | CREAD | HUPCL | CLOCAL;
-
- if ((retval = tty_register_driver(sn_sal_driver))) {
- printk(KERN_ERR "sn_serial: Unable to register tty driver\n");
- return retval;
- }
- return 0;
-}
-
-
-static void __exit
-sn_sal_module_exit(void)
-{
- del_timer_sync(&sn_sal_timer);
- tty_unregister_driver(sn_sal_driver);
- put_tty_driver(sn_sal_driver);
-}
-
-module_init(sn_sal_module_init);
-module_exit(sn_sal_module_exit);
-
-/*
- * Kernel console definitions
- */
-
-#ifdef CONFIG_SGI_L1_SERIAL_CONSOLE
-/*
- * Print a string to the SAL console. The console_lock must be held
- * when we get here.
- */
-static void
-sn_sal_console_write(struct console *co, const char *s, unsigned count)
-{
- unsigned long flags;
- const char *s1;
-
- BUG_ON(!sn_sal_is_asynch);
-
- /* somebody really wants this output, might be an
- * oops, kdb, panic, etc. make sure they get it. */
- if (spin_is_locked(&sn_sal_lock)) {
- synch_flush_xmit();
- /* Output '\r' before each '\n' */
- while ((s1 = memchr(s, '\n', count)) != NULL) {
- sn_func->sal_puts(s, s1 - s);
- sn_func->sal_puts("\r\n", 2);
- count -= s1 + 1 - s;
- s = s1 + 1;
- }
- sn_func->sal_puts(s, count);
- }
- else if (in_interrupt()) {
- spin_lock_irqsave(&sn_sal_lock, flags);
- synch_flush_xmit();
- spin_unlock_irqrestore(&sn_sal_lock, flags);
- /* Output '\r' before each '\n' */
- while ((s1 = memchr(s, '\n', count)) != NULL) {
- sn_func->sal_puts(s, s1 - s);
- sn_func->sal_puts("\r\n", 2);
- count -= s1 + 1 - s;
- s = s1 + 1;
- }
- sn_func->sal_puts(s, count);
- }
- else {
- /* Output '\r' before each '\n' */
- while ((s1 = memchr(s, '\n', count)) != NULL) {
- sn_sal_write(NULL, 0, s, s1 - s);
- sn_sal_write(NULL, 0, "\r\n", 2);
- count -= s1 + 1 - s;
- s = s1 + 1;
- }
- sn_sal_write(NULL, 0, s, count);
- }
-}
-
-static struct tty_driver *
-sn_sal_console_device(struct console *c, int *index)
-{
- *index = c->index;
- return sn_sal_driver;
-}
-
-static int __init
-sn_sal_console_setup(struct console *co, char *options)
-{
- return 0;
-}
-
-
-static struct console sal_console = {
- .name = "ttyS",
- .write = sn_sal_console_write,
- .device = sn_sal_console_device,
- .setup = sn_sal_console_setup,
- .index = -1
-};
-
-static int __init
-sn_sal_serial_console_init(void)
-{
- if (ia64_platform_is("sn2")) {
- sn_sal_switch_to_asynch();
- DPRINTF("sn_sal_serial_console_init : register console\n");
- register_console(&sal_console);
- }
- return 0;
-}
-console_initcall(sn_sal_serial_console_init);
-
-#endif /* CONFIG_SGI_L1_SERIAL_CONSOLE */
diff -Nru a/drivers/serial/Kconfig b/drivers/serial/Kconfig
--- a/drivers/serial/Kconfig 2004-06-18 17:16:46 -05:00
+++ b/drivers/serial/Kconfig 2004-06-18 17:16:46 -05:00
@@ -603,5 +603,12 @@
on your PowerMac as the console, you can do so by answering
Y to this option.

-endmenu
+config SERIAL_SGI_L1_CONSOLE
+ bool "SGI Altix L1 serial console support"
+ select SERIAL_CORE
+ help
+ If you have an SGI Altix and you would like to use the system
+ controller serial port as your console (you want this!),
+ say Y. Otherwise, say N.

+endmenu
diff -Nru a/drivers/serial/Makefile b/drivers/serial/Makefile
--- a/drivers/serial/Makefile 2004-06-18 17:16:46 -05:00
+++ b/drivers/serial/Makefile 2004-06-18 17:16:46 -05:00
@@ -38,3 +38,4 @@
obj-$(CONFIG_SERIAL_DZ) += dz.o
obj-$(CONFIG_SERIAL_SH_SCI) += sh-sci.o
obj-$(CONFIG_SERIAL_BAST_SIO) += bast_sio.o
+obj-$(CONFIG_SERIAL_SGI_L1_CONSOLE) += sn_console.o
diff -Nru a/drivers/serial/sn_console.c b/drivers/serial/sn_console.c
--- /dev/null Wed Dec 31 16:00:00 196900
+++ b/drivers/serial/sn_console.c 2004-06-18 17:16:46 -05:00
@@ -0,0 +1,1138 @@
+/*
+ * C-Brick Serial Port (and console) driver for SGI Altix machines.
+ *
+ * This driver is NOT suitable for talking to the l1-controller for
+ * anything other than 'console activities' --- please use the l1
+ * driver for that.
+ *
+ *
+ * Copyright (c) 2004 Silicon Graphics, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of version 2 of the GNU General Public License
+ * as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it would be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+ *
+ * Further, this software is distributed without any warranty that it is
+ * free of the rightful claim of any third person regarding infringement
+ * or the like. Any license provided herein, whether implied or
+ * otherwise, applies only to this software file. Patent licenses, if
+ * any, provided herein do not apply to combinations of this program with
+ * other software, or any other product whatsoever.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this program; if not, write the Free Software
+ * Foundation, Inc., 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+ *
+ * Contact information: Silicon Graphics, Inc., 1500 Crittenden Lane,
+ * Mountain View, CA 94043, or:
+ *
+ * http://www.sgi.com
+ *
+ * For further information regarding this notice, see:
+ *
+ * http://oss.sgi.com/projects/GenInfo/NoticeExplan
+ */
+
+#include <linux/config.h>
+#include <linux/interrupt.h>
+#include <linux/tty.h>
+#include <linux/serial.h>
+#include <linux/console.h>
+#include <linux/module.h>
+#include <linux/sysrq.h>
+#include <linux/circ_buf.h>
+#include <linux/serial_reg.h>
+#include <linux/delay.h> /* for mdelay */
+#include <linux/miscdevice.h>
+
+#include <asm/sn/simulator.h>
+#include <asm/sn/sn2/sn_private.h>
+#include <linux/serial_core.h>
+#include <asm/sn/sn_sal.h>
+
+/* number of characters we can transmit to the SAL console at a time */
+#define SN_SAL_MAX_CHARS 120
+
+/* 64K, when we're asynch, it must be at least printk's LOG_BUF_LEN to
+ * avoid losing chars, (always has to be a power of 2) */
+#define SN_SAL_BUFFER_SIZE (64 * (1 << 10))
+
+#define SN_SAL_UART_FIFO_DEPTH 16
+#define SN_SAL_UART_FIFO_SPEED_CPS 9600/10
+
+/* sn_transmit_chars() calling args */
+#define TRANSMIT_BUFFERED 0
+#define TRANSMIT_RAW 1
+
+/* To use sysfs only and not use the assigned major and minor, define
+ * the following.. */
+/* #define SYSFS_ONLY 1 */ /* only use SYSFS */
+#define SYSFS_ONLY 0 /* Don't rely on misc_register dynamic minor */
+
+/* Device name we're using */
+#define DEVICE_NAME "ttySG"
+#define DEVICE_NAME_DYNAMIC "ttySG0" /* need full name for misc_register */
+/* The major/minor we are using, ignored for SYSFS_ONLY */
+#define DEVICE_MAJOR 204
+#define DEVICE_MINOR 40
+
+/*
+ * Port definition - this kinda drives it all
+ */
+struct sn_cons_port {
+ struct timer_list sc_timer;
+ struct uart_port sc_port;
+ struct sn_sal_ops {
+ int (*sal_puts_raw) (const char *s, int len);
+ int (*sal_puts) (const char *s, int len);
+ int (*sal_getc) (void);
+ int (*sal_input_pending) (void);
+ void (*sal_wakeup_transmit) (struct sn_cons_port *, int);
+ } *sc_ops;
+ unsigned long sc_interrupt_timeout;
+ int sc_is_asynch;
+};
+
+static struct sn_cons_port sal_console_port;
+
+/* Only used if SYSFS_ONLY is set to 1 */
+static struct miscdevice misc; /* used with misc_register for dynamic */
+
+extern u64 master_node_bedrock_address;
+
+static int sn_debug_printf(const char *fmt, ...);
+
+#undef DEBUG
+#ifdef DEBUG
+#define DPRINTF(x...) sn_debug_printf(x)
+#else
+#define DPRINTF(x...) do { } while (0)
+#endif
+
+/* Prototypes */
+static int snt_hw_puts_raw(const char *, int);
+static int snt_hw_puts_buffered(const char *, int);
+static int snt_poll_getc(void);
+static int snt_poll_input_pending(void);
+static int snt_sim_puts(const char *, int);
+static int snt_sim_getc(void);
+static int snt_sim_input_pending(void);
+static int snt_intr_getc(void);
+static int snt_intr_input_pending(void);
+static void sn_transmit_chars(struct sn_cons_port *, int);
+
+/* A table for polling:
+ */
+static struct sn_sal_ops poll_ops = {
+ .sal_puts_raw = snt_hw_puts_raw,
+ .sal_puts = snt_hw_puts_raw,
+ .sal_getc = snt_poll_getc,
+ .sal_input_pending = snt_poll_input_pending
+};
+
+/* A table for the simulator */
+static struct sn_sal_ops sim_ops = {
+ .sal_puts_raw = snt_sim_puts,
+ .sal_puts = snt_sim_puts,
+ .sal_getc = snt_sim_getc,
+ .sal_input_pending = snt_sim_input_pending
+};
+
+/* A table for interrupts enabled */
+static struct sn_sal_ops intr_ops = {
+ .sal_puts_raw = snt_hw_puts_raw,
+ .sal_puts = snt_hw_puts_buffered,
+ .sal_getc = snt_intr_getc,
+ .sal_input_pending = snt_intr_input_pending,
+ .sal_wakeup_transmit = sn_transmit_chars
+};
+
+/* the console does output in two distinctly different ways:
+ * synchronous (raw) and asynchronous (buffered). initally, early_printk
+ * does synchronous output. any data written goes directly to the SAL
+ * to be output (incidentally, it is internally buffered by the SAL)
+ * after interrupts and timers are initialized and available for use,
+ * the console init code switches to asynchronous output. this is
+ * also the earliest opportunity to begin polling for console input.
+ * after console initialization, console output and tty (serial port)
+ * output is buffered and sent to the SAL asynchronously (either by
+ * timer callback or by UART interrupt) */
+
+
+/* routines for running the console in polling mode */
+
+/**
+ * snt_poll_getc - Get a character from the console in polling mode
+ *
+ */
+static int
+snt_poll_getc(void)
+{
+ int ch;
+
+ ia64_sn_console_getc(&ch);
+ return ch;
+}
+
+/**
+ * snt_poll_input_pending - Check if any input is waiting - polling mode.
+ *
+ */
+static int
+snt_poll_input_pending(void)
+{
+ int status, input;
+
+ status = ia64_sn_console_check(&input);
+ return !status && input;
+}
+
+/* routines for running the console on the simulator */
+
+/**
+ * snt_sim_puts - send to the console, used in simulator mode
+ * @str: String to send
+ * @count: length of string
+ *
+ */
+static int
+snt_sim_puts(const char *str, int count)
+{
+ int counter = count;
+
+#ifdef FLAG_DIRECT_CONSOLE_WRITES
+ /* This is an easy way to pre-pend the output to know whether the output
+ * was done via sal or directly */
+ writeb('[', master_node_bedrock_address + (UART_TX << 3));
+ writeb('+', master_node_bedrock_address + (UART_TX << 3));
+ writeb(']', master_node_bedrock_address + (UART_TX << 3));
+ writeb(' ', master_node_bedrock_address + (UART_TX << 3));
+#endif /* FLAG_DIRECT_CONSOLE_WRITES */
+ while (counter > 0) {
+ writeb(*str, master_node_bedrock_address + (UART_TX << 3));
+ counter--;
+ str++;
+ }
+ return count;
+}
+
+/**
+ * snt_sim_getc - Get character from console in simulator mode
+ *
+ */
+static int
+snt_sim_getc(void)
+{
+ return readb(master_node_bedrock_address + (UART_RX << 3));
+}
+
+/**
+ * snt_sim_input_pending - Check if there is input pending in simulator mode
+ *
+ */
+static int
+snt_sim_input_pending(void)
+{
+ return readb(master_node_bedrock_address +
+ (UART_LSR << 3)) & UART_LSR_DR;
+}
+
+/* routines for an interrupt driven console (normal) */
+
+/**
+ * snt_intr_getc - Get a character from the console, interrupt mode
+ *
+ */
+static int
+snt_intr_getc(void)
+{
+ return ia64_sn_console_readc();
+}
+
+/**
+ * snt_intr_input_pending - Check if input is pending, interrupt mode
+ *
+ */
+static int
+snt_intr_input_pending(void)
+{
+ return ia64_sn_console_intr_status() & SAL_CONSOLE_INTR_RECV;
+}
+
+/* these functions are polled and interrupt */
+
+/**
+ * snt_hw_puts_raw - Send raw string to the console, polled or interrupt mode
+ * @s: String
+ * @len: Length
+ *
+ */
+static int
+snt_hw_puts_raw(const char *s, int len)
+{
+ /* this will call the PROM and not return until this is done */
+ return ia64_sn_console_putb(s, len);
+}
+
+/**
+ * snt_hw_puts_buffered - Send string to console, polled or interrupt mode
+ * @s: String
+ * @len: Length
+ *
+ */
+static int
+snt_hw_puts_buffered(const char *s, int len)
+{
+ /* queue data to the PROM */
+ return ia64_sn_console_xmit_chars((char *)s, len);
+}
+
+/* uart interface structs
+ * These functions are associated with the uart_port that the serial core
+ * infrastructure calls.
+ *
+ * Note: Due to how the console works, many routines are no-ops.
+ */
+
+/**
+ * snp_type - What type of console are we?
+ * @port: Port to operate with (we ignore since we only have one port)
+ *
+ */
+static const char *
+snp_type(struct uart_port *port)
+{
+ return ("SGI SN L1");
+}
+
+/**
+ * snp_tx_empty - Is the transmitter empty? We pretend we're always empty
+ * @port: Port to operate on (we ignore since we only have one port)
+ *
+ */
+static unsigned int
+snp_tx_empty(struct uart_port *port)
+{
+ return 1;
+}
+
+/**
+ * snp_stop_tx - stop the transmitter - no-op for us
+ * @port: Port to operat eon - we ignore - no-op function
+ * @tty_stop: Set to 1 if called via uart_stop
+ *
+ */
+static void
+snp_stop_tx(struct uart_port *port, unsigned int tty_stop)
+{
+}
+
+/**
+ * snp_release_port - Free i/o and resources for port - no-op for us
+ * @port: Port to operate on - we ignore - no-op function
+ *
+ */
+static void
+snp_release_port(struct uart_port *port)
+{
+}
+
+/**
+ * snp_enable_ms - Force modem status interrupts on - no-op for us
+ * @port: Port to operate on - we ignore - no-op function
+ *
+ */
+static void
+snp_enable_ms(struct uart_port *port)
+{
+}
+
+/**
+ * snp_shutdown - shut down the port - free irq and disable - no-op for us
+ * @port: Port to shut down - we ignore
+ *
+ */
+static void
+snp_shutdown(struct uart_port *port)
+{
+}
+
+/**
+ * snp_set_mctrl - set control lines (dtr, rts, etc) - no-op for our console
+ * @port: Port to operate on - we ignore
+ * @mctrl: Lines to set/unset - we ignore
+ *
+ */
+static void
+snp_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+}
+
+/**
+ * snp_get_mctrl - get contorl line info, we just return a static value
+ * @port: port to operate on - we only have one port so we ignore this
+ *
+ */
+static unsigned int
+snp_get_mctrl(struct uart_port *port)
+{
+ return TIOCM_CAR | TIOCM_RNG | TIOCM_DSR | TIOCM_CTS;
+}
+
+/**
+ * snp_stop_rx - Stop the receiver - we ignor ethis
+ * @port: Port to operate on - we ignore
+ *
+ */
+static void
+snp_stop_rx(struct uart_port *port)
+{
+}
+
+/**
+ * snp_start_tx - Start transmitter
+ * @port: Port to operate on
+ * @tty_stop: Set to 1 if called via uart_start
+ *
+ */
+static void
+snp_start_tx(struct uart_port *port, unsigned int tty_stop)
+{
+ if (sal_console_port.sc_ops->sal_wakeup_transmit)
+ sal_console_port.sc_ops->sal_wakeup_transmit(&sal_console_port, TRANSMIT_BUFFERED);
+
+}
+
+/**
+ * snp_break_ctl - handle breaks - ignored by us
+ * @port: Port to operate on
+ * @break_state: Break state
+ *
+ */
+static void
+snp_break_ctl(struct uart_port *port, int break_state)
+{
+}
+
+/**
+ * snp_startup - Start up the serial port - always return 0 (We're always on)
+ * @port: Port to operate on
+ *
+ */
+static int
+snp_startup(struct uart_port *port)
+{
+ return 0;
+}
+
+/**
+ * snp_set_termios - set termios stuff - we ignore these
+ * @port: port to operate on
+ * @termios: New settings
+ * @termios: Old
+ *
+ */
+static void
+snp_set_termios(struct uart_port *port, struct termios *termios,
+ struct termios *old)
+{
+}
+
+/**
+ * snp_request_port - allocate resources for port - ignored by us
+ * @port: port to operate on
+ *
+ */
+static int
+snp_request_port(struct uart_port *port)
+{
+ return 0;
+}
+
+/**
+ * snp_config_port - allocate resources, set up - we ignore, we're always on
+ * @port: Port to operate on
+ * @flags: flags used for port setup
+ *
+ */
+static void
+snp_config_port(struct uart_port *port, int flags)
+{
+}
+
+/* Associate the uart functions above - given to serial core */
+
+static struct uart_ops sn_console_ops = {
+ .tx_empty = snp_tx_empty,
+ .set_mctrl = snp_set_mctrl,
+ .get_mctrl = snp_get_mctrl,
+ .stop_tx = snp_stop_tx,
+ .start_tx = snp_start_tx,
+ .stop_rx = snp_stop_rx,
+ .enable_ms = snp_enable_ms,
+ .break_ctl = snp_break_ctl,
+ .startup = snp_startup,
+ .shutdown = snp_shutdown,
+ .set_termios = snp_set_termios,
+ .pm = NULL,
+ .type = snp_type,
+ .release_port = snp_release_port,
+ .request_port = snp_request_port,
+ .config_port = snp_config_port,
+ .verify_port = NULL,
+};
+
+/* End of uart struct functions and defines */
+
+
+/**
+ * early_printk_sn_sal - The early printk (possible setup) and function call
+ * @s: String to send
+ * @count: length
+ *
+ */
+void
+early_printk_sn_sal(const char *s, unsigned count)
+{
+ extern void early_sn_setup(void);
+
+ if (!sal_console_port.sc_ops) {
+ if (IS_RUNNING_ON_SIMULATOR())
+ sal_console_port.sc_ops = &sim_ops;
+ else
+ sal_console_port.sc_ops = &poll_ops;
+
+ early_sn_setup();
+ }
+ sal_console_port.sc_ops->sal_puts_raw(s, count);
+}
+
+/**
+ * sn_debug_printf - close to hardware debugging printf
+ * @fmt: printf format
+ *
+ * This is as "close to the metal" as we can get, used when the driver
+ * itself may be broken.
+ *
+ */
+static int
+sn_debug_printf(const char *fmt, ...)
+{
+ static char printk_buf[1024];
+ int printed_len;
+ va_list args;
+
+ va_start(args, fmt);
+ printed_len = vsnprintf(printk_buf, sizeof (printk_buf), fmt, args);
+ early_printk_sn_sal(printk_buf, printed_len);
+ va_end(args);
+ return printed_len;
+}
+
+/*
+ * Interrupt handling routines.
+ */
+
+
+/**
+ * sn_receive_chars - Grab characters, pass them to tty layer
+ * @port: Port to operate on
+ * @regs: Saved registers (needed by uart_handle_sysrq_char)
+ *
+ * Note: If we're not registered with the serial core infrastructure yet,
+ * we don't try to send characters to it...
+ *
+ */
+static void
+sn_receive_chars(struct sn_cons_port *port, struct pt_regs *regs)
+{
+ int ch;
+ struct tty_struct *tty;
+
+ if (!port) {
+ printk(KERN_ERR "sn_receive_chars - port NULL so can't receieve\n");
+ return;
+ }
+
+ if (!port->sc_ops) {
+ printk(KERN_ERR "sn_receive_chars - port->sc_ops NULL so can't receieve\n");
+ return;
+ }
+
+ if (port->sc_port.info) {
+ /* The serial_core stuffs are initilized, use them */
+ tty = port->sc_port.info->tty;
+ }
+ else {
+ /* Not registered yet - can't pass to tty layer. */
+ tty = NULL;
+ }
+
+ while (port->sc_ops->sal_input_pending()) {
+ ch = port->sc_ops->sal_getc();
+ if (ch < 0) {
+ printk(KERN_ERR "sn_console: An error occured while "
+ "obtaining data from the console (0x%0x)\n", ch);
+ break;
+ }
+#if defined(CONFIG_SERIAL_SGI_L1_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+ if (uart_handle_sysrq_char(&port->sc_port, ch, regs))
+ continue;
+#endif /* CONFIG_SERIAL_SGI_L1_CONSOLE && CONFIG_MAGIC_SYSRQ */
+
+ /* record the character to pass up to the tty layer */
+ if (tty) {
+ *tty->flip.char_buf_ptr = ch;
+ *tty->flip.flag_buf_ptr = TTY_NORMAL;
+ tty->flip.char_buf_ptr++;
+ tty->flip.count++;
+ if (tty->flip.count == TTY_FLIPBUF_SIZE)
+ break;
+ }
+ else {
+ }
+ port->sc_port.icount.rx++;
+ }
+
+ if (tty)
+ tty_flip_buffer_push(tty);
+}
+
+/**
+ * sn_transmit_chars - grab characters from serial core, send off
+ * @port: Port to operate on
+ * @raw: Transmit raw or buffered
+ *
+ * Note: If we're early, before we're registered with serial core, the
+ * writes are going through sn_sal_console_write because that's how
+ * register_console has been set up. We currently could have asynch
+ * polls calling this function due to sn_sal_switch_to_asynch but we can
+ * ignore them until we register with the serial core stuffs.
+ *
+ */
+static void
+sn_transmit_chars(struct sn_cons_port *port, int raw)
+{
+ int xmit_count, tail, head, loops, ii;
+ int result;
+ char *start;
+ struct circ_buf *xmit;
+
+ if (!port)
+ return;
+
+ BUG_ON(!port->sc_is_asynch);
+
+ if (port->sc_port.info) {
+ /* We're initilized, using serial core infrastructure */
+ xmit = &port->sc_port.info->xmit;
+ }
+ else {
+ /* Probably sn_sal_switch_to_asynch has been run but serial core isn't
+ * initilized yet. Just return. Writes are going through
+ * sn_sal_console_write (due to register_console) at this time.
+ */
+ return;
+ }
+
+ if (uart_circ_empty(xmit) || uart_tx_stopped(&port->sc_port)) {
+ /* Nothing to do. */
+ return;
+ }
+
+ head = xmit->head;
+ tail = xmit->tail;
+ start = &xmit->buf[tail];
+
+ /* twice around gets the tail to the end of the buffer and
+ * then to the head, if needed */
+ loops = (head < tail) ? 2 : 1;
+
+ for (ii = 0; ii < loops; ii++) {
+ xmit_count = (head < tail) ?
+ (UART_XMIT_SIZE - tail) : (head - tail);
+
+ if (xmit_count > 0) {
+ if (raw == TRANSMIT_RAW)
+ result =
+ port->sc_ops->sal_puts_raw(start,
+ xmit_count);
+ else
+ result =
+ port->sc_ops->sal_puts(start, xmit_count);
+#ifdef DEBUG
+ if (!result)
+ sn_debug_printf("`");
+#endif
+ if (result > 0) {
+ xmit_count -= result;
+ port->sc_port.icount.tx += result;
+ tail += result;
+ tail &= UART_XMIT_SIZE - 1;
+ xmit->tail = tail;
+ start = &xmit->buf[tail];
+ }
+ }
+ }
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(&port->sc_port);
+
+ if (uart_circ_empty(xmit))
+ snp_stop_tx(&port->sc_port, 0); /* no-op for us */
+}
+
+/**
+ * sn_sal_interrupt - Handle console interrupts
+ * @irq: irq #, useful for debug statements
+ * @dev_id: our pointer to our port (sn_cons_port which contains the uart port)
+ * @regs: Saved registers, used by sn_receive_chars for uart_handle_sysrq_char
+ *
+ */
+static irqreturn_t
+sn_sal_interrupt(int irq, void *dev_id, struct pt_regs *regs)
+{
+ struct sn_cons_port *port = (struct sn_cons_port *) dev_id;
+ unsigned long flags;
+ int status = ia64_sn_console_intr_status();
+
+ if (!port)
+ return IRQ_NONE;
+
+ spin_lock_irqsave(&port->sc_port.lock, flags);
+ if (status & SAL_CONSOLE_INTR_RECV) {
+ sn_receive_chars(port, regs);
+ }
+ if (status & SAL_CONSOLE_INTR_XMIT) {
+ sn_transmit_chars(port, TRANSMIT_BUFFERED);
+ }
+ spin_unlock_irqrestore(&port->sc_port.lock, flags);
+ return IRQ_HANDLED;
+}
+
+/**
+ * sn_sal_connect_interrupt - Request interrupt, handled by sn_sal_interrupt
+ * @port: Our sn_cons_port (which contains the uart port)
+ *
+ * returns the console irq if interrupt is successfully registered, else 0
+ *
+ */
+static int
+sn_sal_connect_interrupt(struct sn_cons_port *port)
+{
+ if (request_irq(SGI_UART_VECTOR, sn_sal_interrupt, SA_INTERRUPT,
+ "SAL console driver", port) >= 0) {
+ return SGI_UART_VECTOR;
+ }
+
+ printk(KERN_INFO "sn_console: console proceeding in polled mode\n");
+ return 0;
+}
+
+/**
+ * sn_sal_timer_poll - this function handles polled console mode
+ * @data: A pointer to our sn_cons_port (which contains the uart port)
+ *
+ * data is the pointer that init_timer will store for us. This function is
+ * associated with init_timer to see if there is any console traffic.
+ * Obviously not used in interrupt mode
+ *
+ */
+static void
+sn_sal_timer_poll(unsigned long data)
+{
+ struct sn_cons_port *port = (struct sn_cons_port *) data;
+ unsigned long flags;
+
+ if (!port)
+ return;
+
+ if (!port->sc_port.irq) {
+ spin_lock_irqsave(&port->sc_port.lock, flags);
+ sn_receive_chars(port, NULL);
+ sn_transmit_chars(port, TRANSMIT_RAW);
+ spin_unlock_irqrestore(&port->sc_port.lock, flags);
+ mod_timer(&port->sc_timer,
+ jiffies + port->sc_interrupt_timeout);
+ }
+}
+
+/*
+ * Boot-time initialization code
+ */
+
+/**
+ * sn_sal_switch_to_asynch - Switch to async mode (as opposed to synch)
+ * @port: Our sn_cons_port (which contains the uart port)
+ *
+ * So this is used by sn_sal_serial_console_init (early on, before we're
+ * registered with serial core). It's also used by sn_sal_module_init
+ * right after we've registered with serial core. The later only happens
+ * if we didn't already come through here via sn_sal_serial_console_init.
+ *
+ */
+static void __init
+sn_sal_switch_to_asynch(struct sn_cons_port *port)
+{
+ unsigned long flags;
+
+ if (!port)
+ return;
+
+ DPRINTF("sn_console: about to switch to asynchronous console\n");
+
+ /* without early_printk, we may be invoked late enough to race
+ * with other cpus doing console IO at this point, however
+ * console interrupts will never be enabled */
+ spin_lock_irqsave(&port->sc_port.lock, flags);
+
+ /* early_printk invocation may have done this for us */
+ if (!port->sc_ops) {
+ if (IS_RUNNING_ON_SIMULATOR())
+ port->sc_ops = &sim_ops;
+ else
+ port->sc_ops = &poll_ops;
+ }
+
+ /* we can't turn on the console interrupt (as request_irq
+ * calls kmalloc, which isn't set up yet), so we rely on a
+ * timer to poll for input and push data from the console
+ * buffer.
+ */
+ init_timer(&port->sc_timer);
+ port->sc_timer.function = sn_sal_timer_poll;
+ port->sc_timer.data = (unsigned long) port;
+
+ if (IS_RUNNING_ON_SIMULATOR())
+ port->sc_interrupt_timeout = 6;
+ else {
+ /* 960cps / 16 char FIFO = 60HZ
+ * HZ / (SN_SAL_FIFO_SPEED_CPS / SN_SAL_FIFO_DEPTH) */
+ port->sc_interrupt_timeout =
+ HZ * SN_SAL_UART_FIFO_DEPTH / SN_SAL_UART_FIFO_SPEED_CPS;
+ }
+ mod_timer(&port->sc_timer, jiffies + port->sc_interrupt_timeout);
+
+ port->sc_is_asynch = 1;
+ spin_unlock_irqrestore(&port->sc_port.lock, flags);
+}
+
+/**
+ * sn_sal_switch_to_interrupts - Switch to interrupt driven mode
+ * @port: Our sn_cons_port (which contains the uart port)
+ *
+ * In sn_sal_module_init, after we're registered with serial core and
+ * the port is added, this function is called to switch us to interrupt
+ * mode. We were previously in asynch/polling mode (using init_timer).
+ *
+ * We attempt to switch to interrupt mode here by calling
+ * sn_sal_connect_interrupt. If that works out, we enable receive interrupts.
+ */
+static void __init
+sn_sal_switch_to_interrupts(struct sn_cons_port *port)
+{
+ int irq;
+ unsigned long flags;
+
+ if (!port)
+ return;
+
+ DPRINTF("sn_console: switching to interrupt driven console\n");
+
+ spin_lock_irqsave(&port->sc_port.lock, flags);
+
+ irq = sn_sal_connect_interrupt(port);
+
+ if (irq) {
+ port->sc_port.irq = irq;
+ port->sc_ops = &intr_ops;
+
+ /* turn on receive interrupts */
+ ia64_sn_console_intr_enable(SAL_CONSOLE_INTR_RECV);
+ }
+ spin_unlock_irqrestore(&port->sc_port.lock, flags);
+}
+
+/*
+ * Kernel console definitions
+ */
+
+#ifdef CONFIG_SERIAL_SGI_L1_CONSOLE
+static void sn_sal_console_write(struct console *, const char *, unsigned);
+static int __init sn_sal_console_setup(struct console *, char *);
+extern struct uart_driver sal_console_uart;
+extern struct tty_driver *uart_console_device(struct console *, int *);
+
+static struct console sal_console = {
+ .name = DEVICE_NAME,
+ .write = sn_sal_console_write,
+ .device = uart_console_device,
+ .setup = sn_sal_console_setup,
+ .index = -1, /* unspecified */
+ .data = &sal_console_uart,
+};
+
+#define SAL_CONSOLE &sal_console
+#else
+#define SAL_CONSOLE 0
+#endif /* CONFIG_SERIAL_SGI_L1_CONSOLE */
+
+static struct uart_driver sal_console_uart = {
+ .owner = THIS_MODULE,
+ .driver_name = "sn_console",
+ .dev_name = DEVICE_NAME,
+ .major = 0, /* major/minor set at registration time per SYSFS_ONLY */
+ .minor = 0,
+ .nr = 1, /* one port */
+ .cons = SAL_CONSOLE,
+};
+
+/**
+ * sn_sal_module_init - When the kernel loads us, get us rolling w/ serial core
+ *
+ * Before this is called, we've been printing kernel messages in a special
+ * early mode not making use of the serial core infrastructure. When our
+ * driver is loaded for real, we register the driver and port with serial
+ * core and try to enable interrupt driven mode.
+ *
+ */
+static int __init
+sn_sal_module_init(void)
+{
+ int retval;
+
+ printk(KERN_INFO "sn_console: Console driver init\n");
+
+ if (!ia64_platform_is("sn2"))
+ return -ENODEV;
+
+ if (SYSFS_ONLY == 1) {
+ misc.minor = MISC_DYNAMIC_MINOR;
+ misc.name = DEVICE_NAME_DYNAMIC;
+ retval = misc_register(&misc);
+ if (retval != 0) {
+ printk("Failed to register console device using misc_register.\n");
+ return -ENODEV;
+ }
+ sal_console_uart.major = MISC_MAJOR;
+ sal_console_uart.minor = misc.minor;
+ }
+ else {
+ sal_console_uart.major = DEVICE_MAJOR;
+ sal_console_uart.minor = DEVICE_MINOR;
+ }
+
+ /* We register the driver and the port before switching to interrupts
+ * or async above so the proper uart structures are populated */
+
+ if (uart_register_driver(&sal_console_uart) < 0) {
+ printk("ERROR sn_sal_module_init failed uart_register_driver, line %d\n",
+ __LINE__);
+ return -ENODEV;
+ }
+
+ sal_console_port.sc_port.lock = SPIN_LOCK_UNLOCKED;
+
+ /* Setup the port struct with the minimum needed */
+ sal_console_port.sc_port.membase = (char *)1; /* just needs to be non-zero */
+ sal_console_port.sc_port.type = PORT_16550A;
+ sal_console_port.sc_port.fifosize = SN_SAL_MAX_CHARS;
+ sal_console_port.sc_port.ops = &sn_console_ops;
+ sal_console_port.sc_port.line = 0;
+
+ if (uart_add_one_port(&sal_console_uart, &sal_console_port.sc_port) < 0) {
+ /* error - not sure what I'd do - so I'll do nothing */
+ printk(KERN_ERR "%s: unable to add port\n", __FUNCTION__);
+ }
+
+ /* when this driver is compiled in, the console initialization
+ * will have already switched us into asynchronous operation
+ * before we get here through the module initcalls */
+ if (!sal_console_port.sc_is_asynch) {
+ sn_sal_switch_to_asynch(&sal_console_port);
+ }
+
+ /* at this point (module_init) we can try to turn on interrupts */
+ if (!IS_RUNNING_ON_SIMULATOR()) {
+ sn_sal_switch_to_interrupts(&sal_console_port);
+ }
+ return 0;
+}
+
+/**
+ * sn_sal_module_exit - When we're unloaded, remove the driver/port
+ *
+ */
+static void __exit
+sn_sal_module_exit(void)
+{
+ del_timer_sync(&sal_console_port.sc_timer);
+ uart_remove_one_port(&sal_console_uart, &sal_console_port.sc_port);
+ uart_unregister_driver(&sal_console_uart);
+ misc_deregister(&misc);
+}
+
+module_init(sn_sal_module_init);
+module_exit(sn_sal_module_exit);
+
+#ifdef CONFIG_SERIAL_SGI_L1_CONSOLE
+
+/**
+ * puts_raw_fixed - sn_sal_console_write helper for adding \r's as required
+ * @s: input string
+ * @count: length
+ *
+ * We need a \r ahead of every \n for direct writes through
+ * ia64_sn_console_putb (what sal_puts_raw below actually does).
+ *
+ */
+static void puts_raw_fixed(const char *s, int count)
+{
+ const char *s1;
+ struct sn_cons_port *port = &sal_console_port;
+
+ /* Output '\r' before each '\n' */
+ while ((s1 = memchr(s, '\n', count)) != NULL) {
+ port->sc_ops->sal_puts_raw(s, s1 - s);
+ port->sc_ops->sal_puts_raw("\r\n", 2);
+ count -= s1 + 1 - s;
+ s = s1 + 1;
+ }
+ port->sc_ops->sal_puts_raw(s, count);
+}
+
+/**
+ * sn_sal_console_write - Print statements before serial core available
+ * @console: Console to operate on - we ignore since we have just one
+ * @s: String to send
+ * @count: length
+ *
+ * This is referenced in the console struct. It is used for early
+ * console printing before we register with serial core and for things
+ * such as kdb. The console_lock must be held when we get here.
+ *
+ * This function has some code for trying to print output even if the lock
+ * is held. We try to cover the case where a lock holder could have died.
+ * We don't use this special case code if we're not registered with serial
+ * core yet. After we're registered with serial core, the only time this
+ * function would be used is for high level kernel output like magic sys req,
+ * kdb, and printk's.
+ */
+static void
+sn_sal_console_write(struct console *co, const char *s, unsigned count)
+{
+ unsigned long flags = 0;
+ struct sn_cons_port *port = &sal_console_port;
+#if defined(CONFIG_SMP) || defined(CONFIG_PREEMPT)
+ static int stole_lock = 0;
+#endif
+
+ BUG_ON(!port->sc_is_asynch);
+
+ /* We can't look at the xmit buffer if we're not registered with serial core
+ * yet. So only do the fancy recovery after registering
+ */
+ if (port->sc_port.info) {
+
+ /* somebody really wants this output, might be an
+ * oops, kdb, panic, etc. make sure they get it. */
+#if defined(CONFIG_SMP) || defined(CONFIG_PREEMPT)
+ if (spin_is_locked(&port->sc_port.lock)) {
+ int lhead = port->sc_port.info->xmit.head;
+ int ltail = port->sc_port.info->xmit.tail;
+ int counter, got_lock = 0;
+
+ /*
+ * We attempt to determine if someone has died with the
+ * lock. We wait ~20 secs after the head and tail ptrs
+ * stop moving and assume the lock holder is not functional
+ * and plow ahead. If the lock is freed within the time out
+ * period we re-get the lock and go ahead normally. We also
+ * remember if we have plowed ahead so that we don't have
+ * to wait out the time out period again - the asumption
+ * is that we will time out again.
+ */
+
+ for (counter = 0; counter < 150; mdelay(125), counter++) {
+ if (!spin_is_locked(&port->sc_port.lock) || stole_lock) {
+ if (!stole_lock) {
+ spin_lock_irqsave(&port->sc_port.lock, flags);
+ got_lock = 1;
+ }
+ break;
+ }
+ else {
+ /* still locked */
+ if ((lhead != port->sc_port.info->xmit.head) || (ltail != port->sc_port.info->xmit.tail)) {
+ lhead = port->sc_port.info->xmit.head;
+ ltail = port->sc_port.info->xmit.tail;
+ counter = 0;
+ }
+ }
+ }
+ /* flush anything in the serial core xmit buffer, raw */
+ sn_transmit_chars(port, 1);
+ if (got_lock) {
+ spin_unlock_irqrestore(&port->sc_port.lock, flags);
+ stole_lock = 0;
+ }
+ else {
+ /* fell thru */
+ stole_lock = 1;
+ }
+ puts_raw_fixed(s, count);
+ }
+ else {
+ stole_lock = 0;
+#endif
+ spin_lock_irqsave(&port->sc_port.lock, flags);
+ sn_transmit_chars(port, 1);
+ spin_unlock_irqrestore(&port->sc_port.lock, flags);
+
+ puts_raw_fixed(s, count);
+ }
+ }
+ else {
+ /* Not yet registered with serial core - simple case */
+ puts_raw_fixed(s, count);
+ }
+}
+
+
+/**
+ * sn_sal_console_setup - Set up console for early printing
+ * @co: Console to work with
+ * @options: Options to set
+ *
+ * Altix console doesn't do anything with baud rates, etc, anyway.
+ * However, the console struct requires this function...
+ *
+ */
+static int __init
+sn_sal_console_setup(struct console *co, char *options)
+{
+ return 0;
+}
+
+/**
+ * sn_sal_serial_console_init - Early console output - set up for register
+ *
+ */
+static int __init
+sn_sal_serial_console_init(void)
+{
+ if (ia64_platform_is("sn2")) {
+ sn_sal_switch_to_asynch(&sal_console_port);
+ DPRINTF ("sn_sal_serial_console_init : register console\n");
+ register_console(&sal_console);
+ }
+ return 0;
+}
+
+console_initcall(sn_sal_serial_console_init);
+
+#endif /* CONFIG_SERIAL_SGI_L1_CONSOLE */


2004-06-22 18:29:22

by Andrew Morton

[permalink] [raw]
Subject: Re: [PATCH 2.6] Altix serial driver

Pat Gefre <[email protected]> wrote:
>
> 2.6 patch for our console driver. We converted the driver to use the
> serial core functions. Also some changes to use sysfs/udev and a new
> major number.

Well it doesn't use a new major, does it?

+#define DEVICE_MAJOR 204
+#define DEVICE_MINOR 40

Which is:

204 char Low-density serial ports
0 = /dev/ttyLU0 LinkUp Systems L72xx UART - port 0
...
32 = /dev/ttyDB0 DataBooster serial port 0
...
39 = /dev/ttyDB7 DataBooster serial port 7

205 char Low-density serial ports (alternate device)


which seems reasonable, I suppose, but a patch to devices.txt is needed
please.

2004-06-22 18:39:46

by Christoph Hellwig

[permalink] [raw]
Subject: Re: [PATCH 2.6] Altix serial driver

On Tue, Jun 22, 2004 at 11:24:42AM -0700, Andrew Morton wrote:
> which seems reasonable, I suppose, but a patch to devices.txt is needed
> please.

Umm, devices.txt isn managed by LANANA, better ask them.

2004-06-23 14:44:25

by Patrick Gefre

[permalink] [raw]
Subject: Re: [PATCH 2.6] Altix serial driver

On Tue, 22 Jun 2004, Christoph Hellwig wrote:

+ On Tue, Jun 22, 2004 at 11:24:42AM -0700, Andrew Morton wrote:
+ > which seems reasonable, I suppose, but a patch to devices.txt is needed
+ > please.
+
+ Umm, devices.txt isn managed by LANANA, better ask them.
+


Guess I should have said "different" major/minor. We have asked lanana
for our own major/minor - but, as yet, no response.... So we picked a
different one.


-- Pat

2004-06-23 15:02:19

by Christoph Hellwig

[permalink] [raw]
Subject: Re: [PATCH 2.6] Altix serial driver

On Wed, Jun 23, 2004 at 09:42:17AM -0500, Pat Gefre wrote:
> Guess I should have said "different" major/minor. We have asked lanana
> for our own major/minor - but, as yet, no response.... So we picked a
> different one.

Please wait a resonse from LANANA then. As you already have that support
just kill the SYSFS_ONLY ifdef (which is grossly misnamed, btw - people have
used dynamic majors and minnors long before sysfs was invented)

2004-06-23 15:08:50

by Erik Jacobson

[permalink] [raw]
Subject: Re: [PATCH 2.6] Altix serial driver

> On Wed, Jun 23, 2004 at 09:42:17AM -0500, Pat Gefre wrote:
> > Guess I should have said "different" major/minor. We have asked lanana
> > for our own major/minor - but, as yet, no response.... So we picked a
> > different one.
> Please wait a resonse from LANANA then. As you already have that support
> just kill the SYSFS_ONLY ifdef (which is grossly misnamed, btw - people have
> used dynamic majors and minnors long before sysfs was invented)

Well, the horrible name was my fault.

LANANA has been unresponsive and their site states they aren't accepting
2.6 submissions.

Using dynamic minors doesn't work with many distros. One distro, for
example, opens the console up before /dev is populated by by sysfs.

So dynamic won't work for us but we left it in for the future and to show
we had tried it.

--
Erik Jacobson - Linux System Software - Silicon Graphics - Eagan, Minnesota