On Monday 21 March 2005 01:46, Andrew Morton wrote:
>
> Do you think your recent work on ti12xx_hook() will help this guy?
may be. it really sounds like the exact same problem..
>
> (Did a patch come out of that, btw?)
the one i sent was buggy for those reasons:
- the TI hook function override that of yenta which does the very wrong
thing in a system with mixed TI/non TI bridges (which actually exists)
- it can only handle TI's with just one slot
- it fails on older TI's (125x series)
another problem is that those things can have 1001 configurations.
single slot devices are not a problem but dual-slot are. with recent
bridges in "normal" mode (function 0 uses INTA, function 1 uses INTB)
it's also not a problem. but the modes INTRTIE and ALL_SERIAL are
because disabling that will cause regressions with a working card
inserted. and the older bridges habe more that one pin that can
be configured as INTA / INTB. i can code it up, no problem (minus
ALL_SERIAL and INTRTIE for dual-slots)
a slightly different approach is just to return IRQ_HANDLED for
every interrupt durning power-on of the card. doesn't solve the
interrupt storm of course...the kernel 2.4 behavior...patch attached...
it compiles and boots here but is otherwise untested (i don't have a TI
bridge around anymore)
rgds
-daniel
>
> Begin forwarded message:
>
> Date: Sun, 20 Mar 2005 18:53:47 -0500
> From: Ron Gage <[email protected]>
> To: [email protected]
> Subject: Major problem with PCMCIA/Yenta system
>
>
> Greetings:
>
> I have been trying to get a recently acquired Cardbus based USB 2.0 card
> working under 2.6 for the past weekend. It's not going well.
>
> Everytime I plug the card into the computer, the entire PCMCIA system just
> dies, taking my network connectivity with it. I have to do a power off reset
> to recover.
>
> The cardbus card is based on the ALI USB chipset. This shows up as both an
> EHCI and an OHCI device under 2.6.11.5. My laptop, an older HP Pavilion
> N5150 has a UHCI based chipset:
>
> 00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev
> 03)
> 00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev
> 03)
> 00:04.0 CardBus bridge: Texas Instruments PCI1420
> 00:04.1 CardBus bridge: Texas Instruments PCI1420
> 00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
> 00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01)
> 00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01)
> 00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 03)
> 00:08.0 Multimedia audio controller: ESS Technology ES1988 Allegro-1 (rev 12)
> 01:01.0 VGA compatible controller: S3 Inc. 86C270-294 Savage/IX-MV (rev 11)
> 02:00.0 Ethernet controller: Digital Equipment Corporation DECchip 21142/43
> (rev 41)
>
>
> My ethernet card is a generic cardbus device.
>
> When I insert the new USB 2.0 card, the kernel reports that it's killing off
> IRQ 11. Here is the actual dump from dmesg:
>
[...]
>
> Again, when the USB card in inserted, the entire PCMCIA system shuts down and
> remains unusuable until powered off.
>
> Kernel is stock 2.6.11.5. I also tried with 2.6.11, 2.6.10, 2.6.9 and 2.6.7 -
> same result. Distribution is Slackware 9.1 - gcc is 3.2.3
>
> HELP!!!
>
>
--- 1.70/drivers/pcmcia/yenta_socket.c 2005-03-11 21:32:12 +01:00
+++ edited/drivers/pcmcia/yenta_socket.c 2005-03-20 17:33:27 +01:00
@@ -405,6 +405,30 @@
}
+static int yenta_generic_hook(struct pcmcia_socket *sock, int operation)
+{
+ struct yenta_socket *socket = container_of(sock, struct yenta_socket, socket);
+
+ switch (operation) {
+ case HOOK_POWER_PRE:
+ /*
+ * re-user probe_status to tell the interrupt handler to ack
+ * everything
+ */
+ socket->probe_status = 0x0f0f0f0f;
+ break;
+
+ case HOOK_POWER_POST:
+ socket->probe_status = 0;
+ break;
+
+ default:
+ break;
+ }
+
+ return 0;
+}
+
static unsigned int yenta_events(struct yenta_socket *socket)
{
u8 csc;
@@ -440,6 +464,10 @@
pcmcia_parse_events(&socket->socket, events);
return IRQ_HANDLED;
}
+
+ if (socket->probe_status == 0x0f0f0f0f)
+ return IRQ_HANDLED;
+
return IRQ_NONE;
}
@@ -673,6 +701,7 @@
.set_socket = yenta_set_socket,
.set_io_map = yenta_set_io_map,
.set_mem_map = yenta_set_mem_map,
+ .generic_hook = yenta_generic_hook,
};
--- 1.125/drivers/pcmcia/cs.c 2005-03-11 21:32:13 +01:00
+++ edited/drivers/pcmcia/cs.c 2005-03-12 21:22:38 +01:00
@@ -508,6 +508,10 @@
cs_err(skt, "unsupported voltage key.\n");
return CS_BAD_TYPE;
}
+
+ if (skt->ops->generic_hook)
+ skt->ops->generic_hook(skt, HOOK_POWER_PRE);
+
skt->socket.flags = 0;
skt->ops->set_socket(skt, &skt->socket);
@@ -522,7 +526,12 @@
return CS_BAD_TYPE;
}
- return socket_reset(skt);
+ status = socket_reset(skt);
+
+ if (skt->ops->generic_hook)
+ skt->ops->generic_hook(skt, HOOK_POWER_POST);
+
+ return status;
}
/*
--- 1.48/include/pcmcia/ss.h 2005-03-11 21:32:13 +01:00
+++ edited/include/pcmcia/ss.h 2005-03-12 21:22:39 +01:00
@@ -77,6 +77,11 @@
/* Use this just for bridge windows */
#define MAP_IOSPACE 0x20
+/* generic hook operations */
+#define HOOK_POWER_PRE 0x01
+#define HOOK_POWER_POST 0x02
+
+
typedef struct pccard_io_map {
u_char map;
u_char flags;
@@ -113,6 +118,7 @@
int (*set_socket)(struct pcmcia_socket *sock, socket_state_t *state);
int (*set_io_map)(struct pcmcia_socket *sock, struct pccard_io_map *io);
int (*set_mem_map)(struct pcmcia_socket *sock, struct pccard_mem_map *mem);
+ int (*generic_hook)(struct pcmcia_socket *sock, int operation);
};
struct pccard_resource_ops {
The patch in it's second revision (where the config register is NOT set to 0)
appears to work. Testing further (but I can say that the PCMCIA system is
not shut down right now).
Testing with a thumb drive now... More later tonight...
On Monday 21 March 2005 17:53, Daniel Ritz wrote:
> On Monday 21 March 2005 01:46, Andrew Morton wrote:
> > Do you think your recent work on ti12xx_hook() will help this guy?
>
> may be. it really sounds like the exact same problem..
>
> > (Did a patch come out of that, btw?)
>
> the one i sent was buggy for those reasons:
> - the TI hook function override that of yenta which does the very wrong
> thing in a system with mixed TI/non TI bridges (which actually exists)
> - it can only handle TI's with just one slot
> - it fails on older TI's (125x series)
>
> another problem is that those things can have 1001 configurations.
> single slot devices are not a problem but dual-slot are. with recent
> bridges in "normal" mode (function 0 uses INTA, function 1 uses INTB)
> it's also not a problem. but the modes INTRTIE and ALL_SERIAL are
> because disabling that will cause regressions with a working card
> inserted. and the older bridges habe more that one pin that can
> be configured as INTA / INTB. i can code it up, no problem (minus
> ALL_SERIAL and INTRTIE for dual-slots)
>
> a slightly different approach is just to return IRQ_HANDLED for
> every interrupt durning power-on of the card. doesn't solve the
> interrupt storm of course...the kernel 2.4 behavior...patch attached...
> it compiles and boots here but is otherwise untested (i don't have a TI
> bridge around anymore)
>
> rgds
> -daniel
>
> > Begin forwarded message:
> >
> > Date: Sun, 20 Mar 2005 18:53:47 -0500
> > From: Ron Gage <[email protected]>
> > To: [email protected]
> > Subject: Major problem with PCMCIA/Yenta system
> >
> >
> > Greetings:
> >
> > I have been trying to get a recently acquired Cardbus based USB 2.0 card
> > working under 2.6 for the past weekend. It's not going well.
> >
> > Everytime I plug the card into the computer, the entire PCMCIA system
> > just dies, taking my network connectivity with it. I have to do a power
> > off reset to recover.
> >
> > The cardbus card is based on the ALI USB chipset. This shows up as both
> > an EHCI and an OHCI device under 2.6.11.5. My laptop, an older HP
> > Pavilion N5150 has a UHCI based chipset:
> >
> > 00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge
> > (rev 03)
> > 00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge
> > (rev 03)
> > 00:04.0 CardBus bridge: Texas Instruments PCI1420
> > 00:04.1 CardBus bridge: Texas Instruments PCI1420
> > 00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
> > 00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01)
> > 00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01)
> > 00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 03)
> > 00:08.0 Multimedia audio controller: ESS Technology ES1988 Allegro-1 (rev
> > 12) 01:01.0 VGA compatible controller: S3 Inc. 86C270-294 Savage/IX-MV
> > (rev 11) 02:00.0 Ethernet controller: Digital Equipment Corporation
> > DECchip 21142/43 (rev 41)
> >
> >
> > My ethernet card is a generic cardbus device.
> >
> > When I insert the new USB 2.0 card, the kernel reports that it's killing
> > off IRQ 11. Here is the actual dump from dmesg:
>
> [...]
>
> > Again, when the USB card in inserted, the entire PCMCIA system shuts down
> > and remains unusuable until powered off.
> >
> > Kernel is stock 2.6.11.5. I also tried with 2.6.11, 2.6.10, 2.6.9 and
> > 2.6.7 - same result. Distribution is Slackware 9.1 - gcc is 3.2.3
> >
> > HELP!!!
>
> --- 1.70/drivers/pcmcia/yenta_socket.c 2005-03-11 21:32:12 +01:00
> +++ edited/drivers/pcmcia/yenta_socket.c 2005-03-20 17:33:27 +01:00
> @@ -405,6 +405,30 @@
> }
>
>
> +static int yenta_generic_hook(struct pcmcia_socket *sock, int operation)
> +{
> + struct yenta_socket *socket = container_of(sock, struct yenta_socket,
> socket); +
> + switch (operation) {
> + case HOOK_POWER_PRE:
> + /*
> + * re-user probe_status to tell the interrupt handler to ack
> + * everything
> + */
> + socket->probe_status = 0x0f0f0f0f;
> + break;
> +
> + case HOOK_POWER_POST:
> + socket->probe_status = 0;
> + break;
> +
> + default:
> + break;
> + }
> +
> + return 0;
> +}
> +
> static unsigned int yenta_events(struct yenta_socket *socket)
> {
> u8 csc;
> @@ -440,6 +464,10 @@
> pcmcia_parse_events(&socket->socket, events);
> return IRQ_HANDLED;
> }
> +
> + if (socket->probe_status == 0x0f0f0f0f)
> + return IRQ_HANDLED;
> +
> return IRQ_NONE;
> }
>
> @@ -673,6 +701,7 @@
> .set_socket = yenta_set_socket,
> .set_io_map = yenta_set_io_map,
> .set_mem_map = yenta_set_mem_map,
> + .generic_hook = yenta_generic_hook,
> };
>
>
> --- 1.125/drivers/pcmcia/cs.c 2005-03-11 21:32:13 +01:00
> +++ edited/drivers/pcmcia/cs.c 2005-03-12 21:22:38 +01:00
> @@ -508,6 +508,10 @@
> cs_err(skt, "unsupported voltage key.\n");
> return CS_BAD_TYPE;
> }
> +
> + if (skt->ops->generic_hook)
> + skt->ops->generic_hook(skt, HOOK_POWER_PRE);
> +
> skt->socket.flags = 0;
> skt->ops->set_socket(skt, &skt->socket);
>
> @@ -522,7 +526,12 @@
> return CS_BAD_TYPE;
> }
>
> - return socket_reset(skt);
> + status = socket_reset(skt);
> +
> + if (skt->ops->generic_hook)
> + skt->ops->generic_hook(skt, HOOK_POWER_POST);
> +
> + return status;
> }
>
> /*
> --- 1.48/include/pcmcia/ss.h 2005-03-11 21:32:13 +01:00
> +++ edited/include/pcmcia/ss.h 2005-03-12 21:22:39 +01:00
> @@ -77,6 +77,11 @@
> /* Use this just for bridge windows */
> #define MAP_IOSPACE 0x20
>
> +/* generic hook operations */
> +#define HOOK_POWER_PRE 0x01
> +#define HOOK_POWER_POST 0x02
> +
> +
> typedef struct pccard_io_map {
> u_char map;
> u_char flags;
> @@ -113,6 +118,7 @@
> int (*set_socket)(struct pcmcia_socket *sock, socket_state_t *state);
> int (*set_io_map)(struct pcmcia_socket *sock, struct pccard_io_map *io);
> int (*set_mem_map)(struct pcmcia_socket *sock, struct pccard_mem_map
> *mem); + int (*generic_hook)(struct pcmcia_socket *sock, int operation);
> };
>
> struct pccard_resource_ops {
--
Ron Gage - Pontiac, Michigan
(MCP, LPIC1, A+, Net+)
On Monday 21 March 2005 17:53, Daniel Ritz wrote:
> On Monday 21 March 2005 01:46, Andrew Morton wrote:
> > Do you think your recent work on ti12xx_hook() will help this guy?
Everyone:
Let there be no confusion here - Daniel came up with this patch. I am only
reporting the aggregate result.
Daniel:
Here is the aggregate patch I am using that is working nicely here...
diff -ur linux-2.6.11.5/drivers/pcmcia/cs.c
linux-2.6.11.5.new/drivers/pcmcia/cs.c
--- linux-2.6.11.5/drivers/pcmcia/cs.c 2005-03-19 01:34:53.000000000 -0500
+++ linux-2.6.11.5.new/drivers/pcmcia/cs.c 2005-03-21 06:49:17.000000000 -0500
@@ -507,6 +507,10 @@
cs_err(skt, "unsupported voltage key.\n");
return CS_BAD_TYPE;
}
+
+ if (skt->ops->generic_hook)
+ skt->ops->generic_hook(skt,HOOK_POWER_PRE);
+
skt->socket.flags = 0;
skt->ops->set_socket(skt, &skt->socket);
@@ -521,7 +525,12 @@
return CS_BAD_TYPE;
}
- return socket_reset(skt);
+ status = socket_reset(skt);
+
+ if (skt->ops->generic_hook)
+ skt->ops->generic_hook(skt, HOOK_POWER_POST);
+
+ return status;
}
/*
diff -ur linux-2.6.11.5/drivers/pcmcia/ti113x.h
linux-2.6.11.5.new/drivers/pcmcia/ti113x.h
--- linux-2.6.11.5/drivers/pcmcia/ti113x.h 2005-03-19 01:34:55.000000000 -0500
+++ linux-2.6.11.5.new/drivers/pcmcia/ti113x.h 2005-03-21 06:54:40.000000000
-0500
@@ -590,6 +590,38 @@
}
}
+
+/*
+ * TI specifiy parts for generic hook. generic hook really is specifiy to the
+ * chipset so there's no point having it in yenta_socket.c (for now)
+ *
+ * some TI's with some CB's produces interrupt storm on power on. it has been
+ * seen with atheros wlan cards on TI1225 and TI1410. solution is simply to
+ * disable any CB interrupts during this time.
+ */
+static int ti12xx_hook(struct pcmcia_socket *sock, int operation)
+{
+ struct yenta_socket *socket = container_of(sock, struct yenta_socket,
socket);
+ u32 tmp;
+
+ switch (operation) {
+ case HOOK_POWER_PRE:
+ tmp = config_readl(socket, TI122X_MFUNC);
+ socket->saved_state[0] = tmp;
+ config_writel(socket, TI122X_MFUNC, tmp & ~(TI122X_MFUNC0_MASK |
TI122X_MFUNC3_MASK));
+ break;
+
+ case HOOK_POWER_POST:
+ config_writel(socket, TI122X_MFUNC, socket->saved_state[0]);
+ break;
+ default:
+ break;
+ }
+
+ return 0;
+}
+
+
static int ti12xx_override(struct yenta_socket *socket)
{
u32 val, val_orig;
@@ -632,6 +664,7 @@
ti12xx_irqroute_func0(socket);
else
ti12xx_irqroute_func1(socket);
+ socket->socket.ops->generic_hook = ti12xx_hook;
return ti_override(socket);
}
diff -ur linux-2.6.11.5/include/pcmcia/ss.h
linux-2.6.11.5.new/include/pcmcia/ss.h
--- linux-2.6.11.5/include/pcmcia/ss.h 2005-03-19 01:35:03.000000000 -0500
+++ linux-2.6.11.5.new/include/pcmcia/ss.h 2005-03-21 06:51:35.000000000 -0500
@@ -77,6 +77,10 @@
/* Use this just for bridge windows */
#define MAP_IOSPACE 0x20
+/* generic hook operations */
+#define HOOK_POWER_PRE 0x01
+#define HOOK_POWER_POST 0x02
+
typedef struct pccard_io_map {
u_char map;
u_char flags;
@@ -113,6 +117,7 @@
int (*set_socket)(struct pcmcia_socket *sock, socket_state_t *state);
int (*set_io_map)(struct pcmcia_socket *sock, struct pccard_io_map *io);
int (*set_mem_map)(struct pcmcia_socket *sock, struct pccard_mem_map *mem);
+ int (*generic_hook)(struct pcmcia_socket *sock, int operation);
};
struct pccard_resource_ops {
--
Ron Gage - Pontiac, Michigan
(MCP, LPIC1, A+, Net+)