I am plowing along as I am learning about the in'n'outs about i386. I am
totally stuck on this one. I would appreciate any help.
As you can see, the function turns off paging mode (of course it
runs from identically mapped page) and tries to jump to an absolute
address at 0x10000000. It appears the machine would reboot when running
"ljmp" instruction.
Any pointers?
I was not too certain about the %cs, %ds business and did quite
a few experiments with different values but with no luck.
Thanks in advance.
Jun
--------------------------
/* [JSUN] we will map this page into identity mapping before execution */
.align 4096
ENTRY(do_os_switching)
/* interrupt is disabled! */
/* the black magic, some copied form relocate_new_kernel, JSUN */
/* Set cr0 to a known state:
* 31 0 == Paging disabled
* 18 0 == Alignment check disabled
* 16 0 == Write protect disabled
* 3 0 == No task switch
* 2 0 == Don't do FP software emulation.
* 0 1 == Proctected mode enabled
*/
movl %cr0, %eax
andl $~((1<<31)|(1<<18)|(1<<16)|(1<<3)|(1<<2)), %eax
orl $(1<<0), %eax
movl %eax, %cr0
/* JSUN, 0x11 was the boot up value for cr0.
movl $0x11, %eax
movl %eax, %cr0
*/
/* clear cr4 */
movl $0, %eax
movl %eax, %cr4
/* why this? */
jmp 1f
1:
/* clear cr3, flush TLB */
movl $0, %eax
movl %eax, %cr3
/*
movl $(__KERNEL_DS),%eax
movl %eax,%ds
movl %eax,%es
movl %eax,%fs
movl %eax,%gs
movl %eax,%ss
*/
ljmp $(__KERNEL_CS), $0x10000000
On Wed, 22 Nov 2006, Jun Sun wrote:
>
> I am plowing along as I am learning about the in'n'outs about i386. I am
> totally stuck on this one. I would appreciate any help.
>
> As you can see, the function turns off paging mode (of course it
> runs from identically mapped page) and tries to jump to an absolute
> address at 0x10000000. It appears the machine would reboot when running
> "ljmp" instruction.
>
> Any pointers?
>
> I was not too certain about the %cs, %ds business and did quite
> a few experiments with different values but with no luck.
>
> Thanks in advance.
>
> Jun
>
> --------------------------
>
> /* [JSUN] we will map this page into identity mapping before execution */
> .align 4096
> ENTRY(do_os_switching)
> /* interrupt is disabled! */
>
> /* the black magic, some copied form relocate_new_kernel, JSUN */
> /* Set cr0 to a known state:
> * 31 0 == Paging disabled
> * 18 0 == Alignment check disabled
> * 16 0 == Write protect disabled
> * 3 0 == No task switch
> * 2 0 == Don't do FP software emulation.
> * 0 1 == Proctected mode enabled
> */
>
> movl %cr0, %eax
> andl $~((1<<31)|(1<<18)|(1<<16)|(1<<3)|(1<<2)), %eax
> orl $(1<<0), %eax
> movl %eax, %cr0
>
>
> /* JSUN, 0x11 was the boot up value for cr0.
> movl $0x11, %eax
> movl %eax, %cr0
> */
>
> /* clear cr4 */
> movl $0, %eax
> movl %eax, %cr4
>
> /* why this? */
> jmp 1f
> 1:
>
> /* clear cr3, flush TLB */
> movl $0, %eax
> movl %eax, %cr3
>
> /*
> movl $(__KERNEL_DS),%eax
> movl %eax,%ds
> movl %eax,%es
> movl %eax,%fs
> movl %eax,%gs
> movl %eax,%ss
> */
>
> ljmp $(__KERNEL_CS), $0x10000000
>
I think it probably resets the instant that you turn off paging. To
turn off paging, you need to copy some code (properly linked) to an
area where there is a 1:1 mapping between virtual and physical addresses.
A safe place is somewhere below 1 megabyte. Then you need to set up a
call descriptor so you can call that code (you can ljump if you never
plan to get back). You then need to clear interrupts on all CPUs (use a
spin-lock). Once you are executing from the new area, you reset your
segments to the new area. The call descriptor would have already set
CS, as would have the long-jump. At this time you can turn off paging
and flush the TLB. You are now in linear-address protected mode.
Cheers,
Dick Johnson
Penguin : Linux version 2.6.16.24 on an i686 machine (5592.72 BogoMips).
New book: http://www.AbominableFirebug.com/
_
****************************************************************
The information transmitted in this message is confidential and may be privileged. Any review, retransmission, dissemination, or other use of this information by persons or entities other than the intended recipient is prohibited. If you are not the intended recipient, please notify Analogic Corporation immediately - by replying to this message or by sending an email to [email protected] - and destroy all copies of this information, including any attachments, without reading or disclosing them.
Thank you.
On Mon, Nov 27, 2006 at 08:58:57AM -0500, linux-os (Dick Johnson) wrote:
>
> I think it probably resets the instant that you turn off paging. To
> turn off paging, you need to copy some code (properly linked) to an
> area where there is a 1:1 mapping between virtual and physical addresses.
> A safe place is somewhere below 1 megabyte. Then you need to set up a
> call descriptor so you can call that code (you can ljump if you never
> plan to get back). You then need to clear interrupts on all CPUs (use a
> spin-lock). Once you are executing from the new area, you reset your
> segments to the new area. The call descriptor would have already set
> CS, as would have the long-jump. At this time you can turn off paging
> and flush the TLB. You are now in linear-address protected mode.
>
Thanks for the reply. But I am pretty much sure I did above correctly.
I use single-instruction infinite loop in the call path to verify
that control does reach last 'ljmp' but not the jump destination.
Below is the hack I made to machine_kexec.c file. As you can see, I
managed to make the identical mapping between virtual and physical addresses.
Note I did not copy the code into the first 1M. In fact the code
is located at 0xc0477000 (0x00477000 in physical). I thought that should be
OK as I did not really go all the way back to real-address mode.
That last suspect I have now is the wrong value in CS descriptor. Does kernel
have a suitable CS descriptor for the last ljmep to 0x10000000 in linear
addressing mode? The CS descriptor seems to be a pretty dark magic to me ...
Cheers.
Jun
-----------------
diff -Nru linux-2.6.17.14-1st/arch/i386/kernel/machine_kexec.c.orig linux-2.6.17.14-1st/arch/i386/kernel/machine_kexec.c
--- linux-2.6.17.14-1st/arch/i386/kernel/machine_kexec.c.orig 2006-10-13 11:55:04.000000000 -0700
+++ linux-2.6.17.14-1st/arch/i386/kernel/machine_kexec.c 2006-11-22 15:01:45.000000000 -0800
@@ -212,3 +212,19 @@
rnk = (relocate_new_kernel_t) reboot_code_buffer;
(*rnk)(page_list, reboot_code_buffer, image->start, cpu_has_pae);
}
+
+extern void do_os_switching(void);
+void os_switch(void)
+{
+ void (*foo)(void);
+
+ /* absolutely no irq */
+ local_irq_disable();
+
+ /* create identity mapping */
+ foo=virt_to_phys(do_os_switching);
+ identity_map_page((unsigned long)foo);
+
+ /* jump to the real address */
+ foo();
+}
On Mon, 27 Nov 2006, Jun Sun wrote:
>
> On Mon, Nov 27, 2006 at 08:58:57AM -0500, linux-os (Dick Johnson) wrote:
>>
>> I think it probably resets the instant that you turn off paging. To
>> turn off paging, you need to copy some code (properly linked) to an
>> area where there is a 1:1 mapping between virtual and physical addresses.
>> A safe place is somewhere below 1 megabyte. Then you need to set up a
>> call descriptor so you can call that code (you can ljump if you never
>> plan to get back). You then need to clear interrupts on all CPUs (use a
>> spin-lock). Once you are executing from the new area, you reset your
>> segments to the new area. The call descriptor would have already set
>> CS, as would have the long-jump. At this time you can turn off paging
>> and flush the TLB. You are now in linear-address protected mode.
>>
>
> Thanks for the reply. But I am pretty much sure I did above correctly.
> I use single-instruction infinite loop in the call path to verify
> that control does reach last 'ljmp' but not the jump destination.
>
> Below is the hack I made to machine_kexec.c file. As you can see, I
> managed to make the identical mapping between virtual and physical addresses.
>
> Note I did not copy the code into the first 1M. In fact the code
> is located at 0xc0477000 (0x00477000 in physical). I thought that should be
> OK as I did not really go all the way back to real-address mode.
>
> That last suspect I have now is the wrong value in CS descriptor. Does kernel
> have a suitable CS descriptor for the last ljmep to 0x10000000 in linear
> addressing mode? The CS descriptor seems to be a pretty dark magic to me ...
>
> Cheers.
>
> Jun
>
> -----------------
> diff -Nru linux-2.6.17.14-1st/arch/i386/kernel/machine_kexec.c.orig linux-2.6.17.14-1st/arch/i386/kernel/machine_kexec.c
> --- linux-2.6.17.14-1st/arch/i386/kernel/machine_kexec.c.orig 2006-10-13 11:55:04.000000000 -0700
> +++ linux-2.6.17.14-1st/arch/i386/kernel/machine_kexec.c 2006-11-22 15:01:45.000000000 -0800
> @@ -212,3 +212,19 @@
> rnk = (relocate_new_kernel_t) reboot_code_buffer;
> (*rnk)(page_list, reboot_code_buffer, image->start, cpu_has_pae);
> }
> +
> +extern void do_os_switching(void);
> +void os_switch(void)
> +{
> + void (*foo)(void);
> +
> + /* absolutely no irq */
> + local_irq_disable();
> +
> + /* create identity mapping */
> + foo=virt_to_phys(do_os_switching);
> + identity_map_page((unsigned long)foo);
> +
> + /* jump to the real address */
> + foo();
> +}
>
Get a copy of the Intel 486 Microprocessor Reference Manual or read it on-
line. There is no way that you can make a call like that. You would need to
call through a task-gate or otherwise set the code-segment and the instruction
pointer at the same instant. First, look at the startup code for a GDT entry
that maps the linear address-space you are using, PLUS allows execution. If
there isn't such an entry, modify an existing one to allow execution. Remember
that CS value, 'segment' in this example. It is probably 0x08, but I don't have
the kernel source on this machine. Do a far jump through something
created as:
.byte 0xea ; Jmp instruction
.short $segment ; Your segment selector
.word $where & ~0xc0000000 ; Your physical offset
where: invd ; Invalidate cache
movl $segment, %eax ; Get your segment
movl %eax, %ds ; Set a couple segments
movl %eax, %es
This must be IN your code path! Now, you are executing at the same
1:1 physical:virtual address. You can remove paging as:
movl %cr0, %eax ; Get value
andl ~$0x80000000, %eax ; Turn off high bit
movl %eax, %cr0 ; Write back
You are still in protected mode, you now have paging disabled.
Cheers,
Dick Johnson
Penguin : Linux version 2.6.16.24 on an i686 machine (5592.72 BogoMips).
New book: http://www.AbominableFirebug.com/
_
****************************************************************
The information transmitted in this message is confidential and may be privileged. Any review, retransmission, dissemination, or other use of this information by persons or entities other than the intended recipient is prohibited. If you are not the intended recipient, please notify Analogic Corporation immediately - by replying to this message or by sending an email to [email protected] - and destroy all copies of this information, including any attachments, without reading or disclosing them.
Thank you.
On Tue, Nov 28, 2006 at 08:46:44AM -0500, linux-os (Dick Johnson) wrote:
>
> On Mon, 27 Nov 2006, Jun Sun wrote:
>
> >
> > On Mon, Nov 27, 2006 at 08:58:57AM -0500, linux-os (Dick Johnson) wrote:
> >>
> >> I think it probably resets the instant that you turn off paging. To
> >> turn off paging, you need to copy some code (properly linked) to an
> >> area where there is a 1:1 mapping between virtual and physical addresses.
> >> A safe place is somewhere below 1 megabyte. Then you need to set up a
> >> call descriptor so you can call that code (you can ljump if you never
> >> plan to get back). You then need to clear interrupts on all CPUs (use a
> >> spin-lock). Once you are executing from the new area, you reset your
> >> segments to the new area. The call descriptor would have already set
> >> CS, as would have the long-jump. At this time you can turn off paging
> >> and flush the TLB. You are now in linear-address protected mode.
> >>
> >
> > Thanks for the reply. But I am pretty much sure I did above correctly.
> > I use single-instruction infinite loop in the call path to verify
> > that control does reach last 'ljmp' but not the jump destination.
> >
> > Below is the hack I made to machine_kexec.c file. As you can see, I
> > managed to make the identical mapping between virtual and physical addresses.
> >
> > Note I did not copy the code into the first 1M. In fact the code
> > is located at 0xc0477000 (0x00477000 in physical). I thought that should be
> > OK as I did not really go all the way back to real-address mode.
> >
> > That last suspect I have now is the wrong value in CS descriptor. Does kernel
> > have a suitable CS descriptor for the last ljmep to 0x10000000 in linear
> > addressing mode? The CS descriptor seems to be a pretty dark magic to me ...
> >
> > Cheers.
> >
> > Jun
> >
> > -----------------
> > diff -Nru linux-2.6.17.14-1st/arch/i386/kernel/machine_kexec.c.orig linux-2.6.17.14-1st/arch/i386/kernel/machine_kexec.c
> > --- linux-2.6.17.14-1st/arch/i386/kernel/machine_kexec.c.orig 2006-10-13 11:55:04.000000000 -0700
> > +++ linux-2.6.17.14-1st/arch/i386/kernel/machine_kexec.c 2006-11-22 15:01:45.000000000 -0800
> > @@ -212,3 +212,19 @@
> > rnk = (relocate_new_kernel_t) reboot_code_buffer;
> > (*rnk)(page_list, reboot_code_buffer, image->start, cpu_has_pae);
> > }
> > +
> > +extern void do_os_switching(void);
> > +void os_switch(void)
> > +{
> > + void (*foo)(void);
> > +
> > + /* absolutely no irq */
> > + local_irq_disable();
> > +
> > + /* create identity mapping */
> > + foo=virt_to_phys(do_os_switching);
> > + identity_map_page((unsigned long)foo);
> > +
> > + /* jump to the real address */
> > + foo();
> > +}
> >
> Get a copy of the Intel 486 Microprocessor Reference Manual or read it on-
> line. There is no way that you can make a call like that.
By "a call like that", you mean "foo()"? Are you sure about that?
The machine_kexec() function in the same file is basically doing the
same way (i.e., use "call *$eax" instead of "ljmp"). That is where I got
my idea from.
In addition, if I put "1: jmp 1b" instruction anywhere *inside*
do_os_switching() I would get infinite hanging instead of reboot,
which seems to suggest I *did* jump into do_os_switching() successfully.
According to Intel Architecture Software Developer's Manual (1997), Vol 3,
page 8-14:
"2. If paging is enabled perform the following operations:
- Transfer program control to linear addresses that are identity mapped to
physical addresses (that is, linear addresses equal physical addresses)
...
"
it does not indicate one has to use "ljmp" to do this control transfer.
> You would need to
> call through a task-gate or otherwise set the code-segment and the instruction
> pointer at the same instant. First, look at the startup code for a GDT entry
> that maps the linear address-space you are using, PLUS allows execution. If
> there isn't such an entry, modify an existing one to allow execution. Remember
> that CS value, 'segment' in this example. It is probably 0x08, but I don't have
> the kernel source on this machine. Do a far jump through something
> created as:
> .byte 0xea ; Jmp instruction
> .short $segment ; Your segment selector
> .word $where & ~0xc0000000 ; Your physical offset
> where: invd ; Invalidate cache
> movl $segment, %eax ; Get your segment
> movl %eax, %ds ; Set a couple segments
> movl %eax, %es
>
> This must be IN your code path! Now, you are executing at the same
> 1:1 physical:virtual address. You can remove paging as:
>
> movl %cr0, %eax ; Get value
> andl ~$0x80000000, %eax ; Turn off high bit
> movl %eax, %cr0 ; Write back
>
> You are still in protected mode, you now have paging disabled.
>
I tried this also. There is no difference in behavior, i.e., it would
hang with "1: jmp 1b" inside and it would reboot without that debugging
line.
As you can see, I am pretty convinced that the last instruction,
"ljmp $(__KERNEL_CS), $0x10000000", is where the problem is. (BTW,
I also have "1: jmp 1b" instruction at 0x10000000).
Cheers.
Jun
On Tue, 28 Nov 2006, Jun Sun wrote:
> On Tue, Nov 28, 2006 at 08:46:44AM -0500, linux-os (Dick Johnson) wrote:
>>
>> On Mon, 27 Nov 2006, Jun Sun wrote:
>>
>>>
>>> On Mon, Nov 27, 2006 at 08:58:57AM -0500, linux-os (Dick Johnson) wrote:
>>>>
>>>> I think it probably resets the instant that you turn off paging. To
>>>> turn off paging, you need to copy some code (properly linked) to an
>>>> area where there is a 1:1 mapping between virtual and physical addresses.
>>>> A safe place is somewhere below 1 megabyte. Then you need to set up a
>>>> call descriptor so you can call that code (you can ljump if you never
>>>> plan to get back). You then need to clear interrupts on all CPUs (use a
>>>> spin-lock). Once you are executing from the new area, you reset your
>>>> segments to the new area. The call descriptor would have already set
>>>> CS, as would have the long-jump. At this time you can turn off paging
>>>> and flush the TLB. You are now in linear-address protected mode.
>>>>
>>>
>>> Thanks for the reply. But I am pretty much sure I did above correctly.
>>> I use single-instruction infinite loop in the call path to verify
>>> that control does reach last 'ljmp' but not the jump destination.
>>>
>>> Below is the hack I made to machine_kexec.c file. As you can see, I
>>> managed to make the identical mapping between virtual and physical addresses.
>>>
>>> Note I did not copy the code into the first 1M. In fact the code
>>> is located at 0xc0477000 (0x00477000 in physical). I thought that should be
>>> OK as I did not really go all the way back to real-address mode.
>>>
>>> That last suspect I have now is the wrong value in CS descriptor. Does kernel
>>> have a suitable CS descriptor for the last ljmep to 0x10000000 in linear
>>> addressing mode? The CS descriptor seems to be a pretty dark magic to me ...
>>>
>>> Cheers.
>>>
>>> Jun
>>>
>>> -----------------
>>> diff -Nru linux-2.6.17.14-1st/arch/i386/kernel/machine_kexec.c.orig linux-2.6.17.14-1st/arch/i386/kernel/machine_kexec.c
>>> --- linux-2.6.17.14-1st/arch/i386/kernel/machine_kexec.c.orig 2006-10-13 11:55:04.000000000 -0700
>>> +++ linux-2.6.17.14-1st/arch/i386/kernel/machine_kexec.c 2006-11-22 15:01:45.000000000 -0800
>>> @@ -212,3 +212,19 @@
>>> rnk = (relocate_new_kernel_t) reboot_code_buffer;
>>> (*rnk)(page_list, reboot_code_buffer, image->start, cpu_has_pae);
>>> }
>>> +
>>> +extern void do_os_switching(void);
>>> +void os_switch(void)
>>> +{
>>> + void (*foo)(void);
>>> +
>>> + /* absolutely no irq */
>>> + local_irq_disable();
>>> +
>>> + /* create identity mapping */
>>> + foo=virt_to_phys(do_os_switching);
>>> + identity_map_page((unsigned long)foo);
>>> +
>>> + /* jump to the real address */
>>> + foo();
>>> +}
>>>
>> Get a copy of the Intel 486 Microprocessor Reference Manual or read it on-
>> line. There is no way that you can make a call like that.
>
> By "a call like that", you mean "foo()"? Are you sure about that?
>
> The machine_kexec() function in the same file is basically doing the
> same way (i.e., use "call *$eax" instead of "ljmp"). That is where I got
> my idea from.
>
> In addition, if I put "1: jmp 1b" instruction anywhere *inside*
> do_os_switching() I would get infinite hanging instead of reboot,
> which seems to suggest I *did* jump into do_os_switching() successfully.
>
> According to Intel Architecture Software Developer's Manual (1997), Vol 3,
> page 8-14:
>
> "2. If paging is enabled perform the following operations:
>
> - Transfer program control to linear addresses that are identity mapped to
> physical addresses (that is, linear addresses equal physical addresses)
> ...
> "
>
> it does not indicate one has to use "ljmp" to do this control transfer.
Assume you are accessing memory at 0xc000-0000. This address, when
page translation is occurring (page 5-17), consists of three parts.
(1) A 12-bit offset 0:11
(2) A 10-bit index 11:21
(3) A 10-bit index 21:31
So 0xc00 is an index into the page directory. If you wish to turn off
translation, you can't just turn off those bits. The next instruction
will be fetched from memory with the page-cache upper bits reset, i.e,
using offset 0 of the page directory. You somehow need to turn off those
bits at the same time the next instruction is fetched. Normally you
use a call gate. However, you can do a long jump which reloads the
segment register. When the instruction book says "transfer control"
it doesn't mean just jump to some offset. When the instruction address is
0xC000-0000, it is not the same as 0x0000-0000. These two addresses are
different (to the CPU) until after those page translation bits are reset, not
before.
>
>> You would need to
>> call through a task-gate or otherwise set the code-segment and the instruction
>> pointer at the same instant. First, look at the startup code for a GDT entry
>> that maps the linear address-space you are using, PLUS allows execution. If
>> there isn't such an entry, modify an existing one to allow execution. Remember
>> that CS value, 'segment' in this example. It is probably 0x08, but I don't have
>> the kernel source on this machine. Do a far jump through something
>> created as:
>> .byte 0xea ; Jmp instruction
>> .short $segment ; Your segment selector
>> .word $where & ~0xc0000000 ; Your physical offset
>> where: invd ; Invalidate cache
>> movl $segment, %eax ; Get your segment
>> movl %eax, %ds ; Set a couple segments
>> movl %eax, %es
>>
>> This must be IN your code path! Now, you are executing at the same
>> 1:1 physical:virtual address. You can remove paging as:
>>
>> movl %cr0, %eax ; Get value
>> andl ~$0x80000000, %eax ; Turn off high bit
>> movl %eax, %cr0 ; Write back
>>
>> You are still in protected mode, you now have paging disabled.
>>
>
> I tried this also. There is no difference in behavior, i.e., it would
> hang with "1: jmp 1b" inside and it would reboot without that debugging
> line.
>
I think you didn't bother to try it.
> As you can see, I am pretty convinced that the last instruction,
> "ljmp $(__KERNEL_CS), $0x10000000", is where the problem is. (BTW,
> I also have "1: jmp 1b" instruction at 0x10000000).
>
Well now you are even trying to jump to something at 0x1000-0000 and
that will certainly kill the machine.
> Cheers.
>
> Jun
>
Cheers,
Dick Johnson
Penguin : Linux version 2.6.16.24 on an i686 machine (5592.72 BogoMips).
New book: http://www.AbominableFirebug.com/
_
****************************************************************
The information transmitted in this message is confidential and may be privileged. Any review, retransmission, dissemination, or other use of this information by persons or entities other than the intended recipient is prohibited. If you are not the intended recipient, please notify Analogic Corporation immediately - by replying to this message or by sending an email to [email protected] - and destroy all copies of this information, including any attachments, without reading or disclosing them.
Thank you.
On Tue, Nov 28, 2006 at 06:49:17PM -0500, linux-os (Dick Johnson) wrote:
>
> On Tue, 28 Nov 2006, Jun Sun wrote:
>
> > On Tue, Nov 28, 2006 at 08:46:44AM -0500, linux-os (Dick Johnson) wrote:
> >>
> >> On Mon, 27 Nov 2006, Jun Sun wrote:
> >>
> >>>
> >>> On Mon, Nov 27, 2006 at 08:58:57AM -0500, linux-os (Dick Johnson) wrote:
> >>>>
> >>>> I think it probably resets the instant that you turn off paging. To
> >>>> turn off paging, you need to copy some code (properly linked) to an
> >>>> area where there is a 1:1 mapping between virtual and physical addresses.
> >>>> A safe place is somewhere below 1 megabyte. Then you need to set up a
> >>>> call descriptor so you can call that code (you can ljump if you never
> >>>> plan to get back). You then need to clear interrupts on all CPUs (use a
> >>>> spin-lock). Once you are executing from the new area, you reset your
> >>>> segments to the new area. The call descriptor would have already set
> >>>> CS, as would have the long-jump. At this time you can turn off paging
> >>>> and flush the TLB. You are now in linear-address protected mode.
> >>>>
> >>>
> >>> Thanks for the reply. But I am pretty much sure I did above correctly.
> >>> I use single-instruction infinite loop in the call path to verify
> >>> that control does reach last 'ljmp' but not the jump destination.
> >>>
> >>> Below is the hack I made to machine_kexec.c file. As you can see, I
> >>> managed to make the identical mapping between virtual and physical addresses.
> >>>
> >>> Note I did not copy the code into the first 1M. In fact the code
> >>> is located at 0xc0477000 (0x00477000 in physical). I thought that should be
> >>> OK as I did not really go all the way back to real-address mode.
> >>>
> >>> That last suspect I have now is the wrong value in CS descriptor. Does kernel
> >>> have a suitable CS descriptor for the last ljmep to 0x10000000 in linear
> >>> addressing mode? The CS descriptor seems to be a pretty dark magic to me ...
> >>>
> >>> Cheers.
> >>>
> >>> Jun
> >>>
> >>> -----------------
> >>> diff -Nru linux-2.6.17.14-1st/arch/i386/kernel/machine_kexec.c.orig linux-2.6.17.14-1st/arch/i386/kernel/machine_kexec.c
> >>> --- linux-2.6.17.14-1st/arch/i386/kernel/machine_kexec.c.orig 2006-10-13 11:55:04.000000000 -0700
> >>> +++ linux-2.6.17.14-1st/arch/i386/kernel/machine_kexec.c 2006-11-22 15:01:45.000000000 -0800
> >>> @@ -212,3 +212,19 @@
> >>> rnk = (relocate_new_kernel_t) reboot_code_buffer;
> >>> (*rnk)(page_list, reboot_code_buffer, image->start, cpu_has_pae);
> >>> }
> >>> +
> >>> +extern void do_os_switching(void);
> >>> +void os_switch(void)
> >>> +{
> >>> + void (*foo)(void);
> >>> +
> >>> + /* absolutely no irq */
> >>> + local_irq_disable();
> >>> +
> >>> + /* create identity mapping */
> >>> + foo=virt_to_phys(do_os_switching);
> >>> + identity_map_page((unsigned long)foo);
> >>> +
> >>> + /* jump to the real address */
> >>> + foo();
> >>> +}
> >>>
> >> Get a copy of the Intel 486 Microprocessor Reference Manual or read it on-
> >> line. There is no way that you can make a call like that.
> >
> > By "a call like that", you mean "foo()"? Are you sure about that?
> >
> > The machine_kexec() function in the same file is basically doing the
> > same way (i.e., use "call *$eax" instead of "ljmp"). That is where I got
> > my idea from.
> >
> > In addition, if I put "1: jmp 1b" instruction anywhere *inside*
> > do_os_switching() I would get infinite hanging instead of reboot,
> > which seems to suggest I *did* jump into do_os_switching() successfully.
> >
> > According to Intel Architecture Software Developer's Manual (1997), Vol 3,
> > page 8-14:
> >
> > "2. If paging is enabled perform the following operations:
> >
> > - Transfer program control to linear addresses that are identity mapped to
> > physical addresses (that is, linear addresses equal physical addresses)
> > ...
> > "
> >
> > it does not indicate one has to use "ljmp" to do this control transfer.
>
> Assume you are accessing memory at 0xc000-0000. This address, when
> page translation is occurring (page 5-17), consists of three parts.
>
> (1) A 12-bit offset 0:11
> (2) A 10-bit index 11:21
> (3) A 10-bit index 21:31
>
> So 0xc00 is an index into the page directory. If you wish to turn off
> translation, you can't just turn off those bits. The next instruction
> will be fetched from memory with the page-cache upper bits reset, i.e,
> using offset 0 of the page directory. You somehow need to turn off those
> bits at the same time the next instruction is fetched. Normally you
> use a call gate. However, you can do a long jump which reloads the
> segment register. When the instruction book says "transfer control"
> it doesn't mean just jump to some offset. When the instruction address is
> 0xC000-0000, it is not the same as 0x0000-0000. These two addresses are
> different (to the CPU) until after those page translation bits are reset, not
> before.
Hmm, if I understand it correctly, identity_map_page() will take
a physical address (aligned along page boundary) and map it into
the same virtual address. So in my case the page starting at 0x00477000
in phys space will be mapped at the virtual address 0x00477000. Is this
understanding correct?
Assuming this understanding is correct, I don't anything wrong with
"call *%eax" where %eax=0x00477000 when paging is still enabled.
If this understanding is wrong, are you suggesting there is a bug
in machine_kexec()? Here is the gist of machine_kexec() code:
NORET_TYPE void machine_kexec(struct kimage *image)
{
...
reboot_code_buffer = page_to_pfn(image->control_code_page)
<< PAGE_SHIFT;
...
identity_map_page(reboot_code_buffer);
memcpy((void *)reboot_code_buffer, relocate_new_kernel,
relocate_new_kernel_size);
...
rnk = (relocate_new_kernel_t) reboot_code_buffer;
(*rnk)(page_list, reboot_code_buffer, image->start, cpu_has_pae);
}
The last statment generates the same "call *%eax" as in my code.
> >
> >> You would need to
> >> call through a task-gate or otherwise set the code-segment and the instruction
> >> pointer at the same instant. First, look at the startup code for a GDT entry
> >> that maps the linear address-space you are using, PLUS allows execution. If
> >> there isn't such an entry, modify an existing one to allow execution. Remember
> >> that CS value, 'segment' in this example. It is probably 0x08, but I don't have
> >> the kernel source on this machine. Do a far jump through something
> >> created as:
> >> .byte 0xea ; Jmp instruction
> >> .short $segment ; Your segment selector
> >> .word $where & ~0xc0000000 ; Your physical offset
> >> where: invd ; Invalidate cache
> >> movl $segment, %eax ; Get your segment
> >> movl %eax, %ds ; Set a couple segments
> >> movl %eax, %es
> >>
> >> This must be IN your code path! Now, you are executing at the same
> >> 1:1 physical:virtual address. You can remove paging as:
> >>
> >> movl %cr0, %eax ; Get value
> >> andl ~$0x80000000, %eax ; Turn off high bit
> >> movl %eax, %cr0 ; Write back
> >>
> >> You are still in protected mode, you now have paging disabled.
> >>
> >
> > I tried this also. There is no difference in behavior, i.e., it would
> > hang with "1: jmp 1b" inside and it would reboot without that debugging
> > line.
> >
>
> I think you didn't bother to try it.
I did. Here is the new code of trying your idea:
extern void do_os_switching(void);
void os_switch(void)
{
void (*foo)(void);
/* absolutely no irq */
local_irq_disable();
/* create identity mapping */
foo=virt_to_phys(do_os_switching);
identity_map_page((unsigned long)foo);
/* jump to the real address */
/*
load_segments();
set_gdt(phys_to_virt(0),0);
set_idt(phys_to_virt(0),0);
foo();
*/
#define __STR(X) #X
#define STR(X) __STR(X)
__asm__ __volatile__ (
"\tljmp $"STR(__KERNEL_CS)",$0x00477000\n");
#undef STR
#undef __STR
}
Again, like I said, using this or not does not seem to make a difference
from doing "call *%eax".
>
> > As you can see, I am pretty convinced that the last instruction,
> > "ljmp $(__KERNEL_CS), $0x10000000", is where the problem is. (BTW,
> > I also have "1: jmp 1b" instruction at 0x10000000).
> >
>
> Well now you are even trying to jump to something at 0x1000-0000 and
> that will certainly kill the machine.
>
Can you elaborate more why this last ljmp will fail? I thought at this point
the paging is turned off, and 0x1000-0000 would simply mean a physical
address - which is a valid physical address in RAM, btw.
Here is the re-post of whole function that contains the ljmp:
ENTRY(do_os_switching)
/* turn off paging and etc */
movl %cr0, %eax
andl $~((1<<31)|(1<<18)|(1<<16)|(1<<3)|(1<<2)), %eax
orl $(1<<0), %eax
movl %eax, %cr0
/* clear cr4 */
movl $0, %eax
movl %eax, %cr4
/* clear cr3, flush TLB */
movl $0, %eax
movl %eax, %cr3
ljmp $(__KERNEL_CS), $0x10000000
Thanks again. And cheers.
Jun
On Tue, Nov 28, 2006 at 05:40:56PM -0800, Jun Sun wrote:
>
> Can you elaborate more why this last ljmp will fail? I thought at this point
> the paging is turned off, and 0x1000-0000 would simply mean a physical
> address - which is a valid physical address in RAM, btw.
>
<snip>
I finally got it working, even though I don't understand at all. :)
I realized that after paging mode is turned off, 0x1000-0000 is actually
at the same flag 4G code segment as caller code. So I tried to just
"call" and that worked.
Here is the excerpt of the related code in case someone else needs to
do the same:
In arch/i386/kernel/machine_kexec.c:
extern void do_os_switching(void);
void os_switch(void)
{
void (*foo)(void);
/* absolutely no irq */
local_irq_disable();
/* create identity mapping */
foo=virt_to_phys(do_os_switching);
identity_map_page((unsigned long)foo);
/* jump to the real address */
load_segments();
set_gdt(phys_to_virt(0),0);
set_idt(phys_to_virt(0),0);
foo();
}
In arch/i386/kernel/acpi/wakeup.S:
.align 4096
ENTRY(do_os_switching)
/* JSUN, 0x11 was the boot up value for cr0. */
movl $0x11, %eax
movl %eax, %cr0
/* clear cr4 */
movl $0, %eax
movl %eax, %cr4
/* clear cr3, flush TLB */
movl $0, %eax
movl %eax, %cr3
movl $0x10000000,%eax
call *%eax
I have a second Linux kernel loaded at 0x1000-0000. Now the only matter
remaining is to figure out why the tsc timer stopped working ... :)
Cheers.
Jun
linux-os (Dick Johnson) wrote:
> Get a copy of the Intel 486 Microprocessor Reference Manual or read it on-
> line. There is no way that you can make a call like that. You would need to
> call through a task-gate or otherwise set the code-segment and the instruction
> pointer at the same instant. First, look at the startup code for a GDT entry
Setting the code segment and instruction pointer at the same time is
exactly what the long jump does.
OP: What is at the linear address 0x10000000?
On Wed, Nov 22, 2006 at 03:41:11PM -0800, Jun Sun wrote:
>
> I am plowing along as I am learning about the in'n'outs about i386. I am
> totally stuck on this one. I would appreciate any help.
>
> As you can see, the function turns off paging mode (of course it
> runs from identically mapped page) and tries to jump to an absolute
> address at 0x10000000. It appears the machine would reboot when running
> "ljmp" instruction.
>
> Any pointers?
>
Pageexec gave me an excellent explanation on why "ljmp" fails. See below.
It is so obvious once you see it. :)
Thanks.
Jun
-----------------
From: [email protected]
To: [email protected]
Date: Fri, 01 Dec 2006 14:35:09 +0200
Subject: failed 'ljmp' in linear addressing mode
hello,
just saw your post on lkml. your original problem was that when you
executed the far jump, the CPU's internal GDT base register was still
loaded with the kernel's virtual address of gdt_table - an address
somewhere high in the (then virtual) address space which when
interpreted as a physical address (you turned off paging, remember)
contained nothing, let alone a valid GDT.
so when the CPU tried to look up __KERNEL_CS in the GDT, it found
nothing there, that in turn triggered an exception which in turn
double then triple faulted as the IDT couldn't be accessed either
for the same reason. later you posted code that shows that you
reload the IDT/GDT with a constant 0, i doubt that will do much
good either on the long run as there's no valid GDT/IDT set up
there normally.
in short, the normal course of action when going from paged protected
mode into non-paged protected mode is to reload IDT/GDT with physical
addresses pointing to valid tables then reload the segment registers
(if they're different from those used in paged mode) then you can go
on with the rest. note that the reload operation uses *two* addresses
(one for the memory operand of lgdt/lidt and one for the actual table
address), both of which had better be of the same kind (physical or
virtual).