to: [email protected]
cc: [email protected]
2.6.19-git libusual: modprobe for usb-storage succeeded, but module is
not present
Linux version 2.6.19-200612081830-g17097758
([email protected]) (gcc version 4.1.1 20061011 ) #16 SMP
PREEMPT Fri Dec 8 18:37:41 CST 2006
Command line: ro root=/dev/VolGroup00/LogVol00 rhgb mem=3583M
...
AMD Athlon(tm) 64 X2 Dual Core Processor 4200+ stepping 01
...
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
...
usbcore: registered new interface driver libusual
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
...
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [APCF] -> GSI 23 (level,
low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:0b.0 to 64
ohci_hcd 0000:00:0b.0: OHCI Host Controller
ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:0b.0: irq 23, io mem 0xfe02f000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [APCL] -> GSI 22 (level,
low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:0b.1 to 64
ehci_hcd 0000:00:0b.1: EHCI Host Controller
ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:0b.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:0b.1
ehci_hcd 0000:00:0b.1: irq 22, io mem 0xfe02e000
ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 8 ports detected
SCSI subsystem initialized
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
ACPI: PCI Interrupt 0000:03:09.0[A] -> Link [APC2] -> GSI 17 (level,
low) -> IRQ 17
usb 2-1: new high speed USB device using ehci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 4 ports detected
usb 2-2: new high speed USB device using ehci_hcd and address 3
usb 2-2: configuration #1 chosen from 1 choice
libusual: modprobe for usb-storage succeeded, but module is not present
usb 2-4: new high speed USB device using ehci_hcd and address 5
usb 2-4: configuration #1 chosen from 1 choice
libusual: modprobe for usb-storage succeeded, but module is not present
usb 2-5: new high speed USB device using ehci_hcd and address 6
usb 2-5: configuration #1 chosen from 1 choice
libusual: modprobe for usb-storage succeeded, but module is not present
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
xboom
On Fri, 08 Dec 2006 19:08:29 -0600, [email protected] wrote:
> usb 2-2: new high speed USB device using ehci_hcd and address 3
> usb 2-2: configuration #1 chosen from 1 choice
> libusual: modprobe for usb-storage succeeded, but module is not present
> usb 2-4: new high speed USB device using ehci_hcd and address 5
> usb 2-4: configuration #1 chosen from 1 choice
> libusual: modprobe for usb-storage succeeded, but module is not present
> usb 2-5: new high speed USB device using ehci_hcd and address 6
> usb 2-5: configuration #1 chosen from 1 choice
> libusual: modprobe for usb-storage succeeded, but module is not present
I don't know what you've done to accomplish it, but either your
modules got separated (e.g. libusual built statically while usb-storage
is dynamic), or your modprobe is toast, or 100 other reasons.
Just deconfigure CONFIG_BLK_DEV_UB and CONFIG_USB_LIBUSUAL
and forget about it all.
I know, I have to think of a workaround for this, but nothing is
readily apparent.
-- Pete
to: [email protected]
cc: [email protected], [email protected]
Re: 2.6.19-git libusual: modprobe for usb-storage succeeded, but
module is not present
> usb 2-2: new high speed USB device using ehci_hcd and address 3
> > usb 2-2: configuration #1 chosen from 1 choice
> > libusual: modprobe for usb-storage succeeded, but module is not present
> > usb 2-4: new high speed USB device using ehci_hcd and address 5
> > usb 2-4: configuration #1 chosen from 1 choice
> > libusual: modprobe for usb-storage succeeded, but module is not present
> > usb 2-5: new high speed USB device using ehci_hcd and address 6
> > usb 2-5: configuration #1 chosen from 1 choice
> > libusual: modprobe for usb-storage succeeded, but module is not present
> I don't know what you've done to accomplish it, but either your
> modules got separated (e.g. libusual built statically while usb-storage
> is dynamic), or your modprobe is toast, or 100 other reasons.
>
> Just deconfigure CONFIG_BLK_DEV_UB and CONFIG_USB_LIBUSUAL
> and forget about it all.
>
> I know, I have to think of a workaround for this, but nothing is
> readily apparent.
>
> -- Pete
was
CONFIG_BLK_DEV_UB=m
CONFIG_USB_LIBUSUAL=y
now
# CONFIG_BLK_DEV_UB is not set
# CONFIG_USB_LIBUSUAL is not set
works ok thanx
xboom