Dear Kernel Developers,
I had some trouble with my usb devices, often showing a disconnect problem. I
did some googleing and saw, that it is a less or more common problem.
This problem is discussed in various internet sites.
log from my machine:
#############################
usb 4-6: new high speed USB device using ehci_hcd and address 7
usb 4-6: configuration #1 chosen from 1 choice
hub 4-6:1.0: USB hub found
hub 4-6:1.0: 4 ports detected
usb 4-6.1: new full speed USB device using ehci_hcd and address 8
usb 4-6.1: device descriptor read/64, error -32
usb 4-6.1: device descriptor read/64, error -32
usb 4-6.1: new full speed USB device using ehci_hcd and address 9
usb 4-6.1: device descriptor read/64, error -110
usb 4-6.1: device descriptor read/64, error -110
usb 4-6.1: new full speed USB device using ehci_hcd and address 10
usb 4-6.1: device not accepting address 10, error -32
usb 4-6.1: new full speed USB device using ehci_hcd and address 11
usb 4-6.1: device not accepting address 11, error -71
usb 4-6: USB disconnect, address 7
usb 4-6: new high speed USB device using ehci_hcd and address 12
usb 4-6: configuration #1 chosen from 1 choice
hub 4-6:1.0: USB hub found
hub 4-6:1.0: 4 ports detected
usb 4-6.1: new full speed USB device using ehci_hcd and address 13
usb 4-6.1: device descriptor read/64, error -32
usb 4-6.1: device descriptor read/64, error -32
usb 4-6.1: new full speed USB device using ehci_hcd and address 14
usb 4-6.1: device descriptor read/64, error -110
usb 4-6.1: device descriptor read/64, error -71
usb 4-6.1: new full speed USB device using ehci_hcd and address 15
usb 4-6.1: device not accepting address 15, error -71
usb 4-6.1: new full speed USB device using ehci_hcd and address 16
usb 4-6.1: device not accepting address 16, error -71
usb 4-6.1: new full speed USB device using ehci_hcd and address 17
usb 4-6.1: configuration #1 chosen from 1 choice
SCSI subsystem initialized
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
usb-storage: device found at 17
usb-storage: waiting for device to settle before scanning
USB Mass Storage support registered.
Vendor: Model: USB Card Reader Rev: 1.05
Type: Direct-Access ANSI SCSI revision: 00
Vendor: Model: USB Card Reader Rev: 1.05
Type: Direct-Access ANSI SCSI revision: 00
Vendor: Model: USB Card Reader Rev: 1.05
Type: Direct-Access ANSI SCSI revision: 00
Vendor: Model: USB Card Reader Rev: 1.05
Type: Direct-Access ANSI SCSI revision: 00
usb-storage: device scan complete
sd 0:0:0:0: Attached scsi removable disk sda
sd 0:0:0:1: Attached scsi removable disk sdb
sd 0:0:0:2: Attached scsi removable disk sdc
sd 0:0:0:3: Attached scsi removable disk sdd
usb 4-6.1: reset full speed USB device using ehci_hcd and address 17
usb 4-6.1: reset full speed USB device using ehci_hcd and address 17
usb 4-6.1: reset full speed USB device using ehci_hcd and address 17
usb 4-6.1: reset full speed USB device using ehci_hcd and address 17
usb 4-6.1: reset full speed USB device using ehci_hcd and address 17
usb 4-6.1: reset full speed USB device using ehci_hcd and address 17
usb 4-6.1: reset full speed USB device using ehci_hcd and address 17
usb 4-6.1: reset full speed USB device using ehci_hcd and address 17
usb 4-6.1: USB disconnect, address 17
#########################
I have a solution/hint to solve this problem.
In my case I had following NOT WORKING config:
internal USB-Card PCI --> USB Hub --> Card Reader
( ali usb card, i-rocks hub, Phision cardreader)
00:08.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
00:08.1 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
00:08.2 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
00:08.3 USB Controller: ALi Corporation USB 2.0 Controller (rev 01)
linux sets it up using:
ehci --> ehci --> ehci (total usb 2.0 support)
Bus 004 Device 028: ID 0d7d:0240 Phison Electronics Corp. I/O-Magic/Transcend
6-in-1 Card Reader
Bus 004 Device 027: ID 05e3:0605 Genesys Logic, Inc. USB 2.0 Hub [ednet]
but only the hub is a usb 2.0 compliant product. the card-reader is usb 1.1!!
So i changed physically the hub back to a 1.1 device.
and now linux sets this to
ohci --> ohci --> ohci
Bus 003 Device 011: ID 0d7d:0240 Phison Electronics Corp. I/O-Magic/Transcend
6-in-1 Card Reader
Bus 003 Device 010: ID 03eb:3301 Atmel Corp. at43301 4-port Hub
And this configuration works perfect, without any trouble any more.
So in my opinion the problem is comming from ehci, which tries to set up a usb
1.1 device in a 2.0 mode. this results in severe timing problems, because the
1.1 device is too slow to handle this protocol, this results in a "dead"
device from the point of view of the driver (no reaction). It disconnects the
device and reconnects it again. It is only a problem, if you use a HUB
between the USB Controller and the end device. I think we have to take care
about the last device in the chain to set it up in the correct way.
now log looks like this (and I am happy):
########################
usb 3-1: USB disconnect, address 8
ohci_hcd 0000:00:08.2: wakeup
usb 3-2: new full speed USB device using ohci_hcd and address 9
usb 3-2: configuration #1 chosen from 1 choice
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 9 if 1 alt 0
proto 2 vid 0x03F0 pid 0x2D11
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
usb 3-1: new full speed USB device using ohci_hcd and address 10
usb 3-1: configuration #1 chosen from 1 choice
hub 3-1:1.0: USB hub found
hub 3-1:1.0: 4 ports detected
usb 3-1.2: new full speed USB device using ohci_hcd and address 11
usb 3-1.2: configuration #1 chosen from 1 choice
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 11
usb-storage: waiting for device to settle before scanning
Vendor: Model: USB Card Reader Rev: 1.05
Type: Direct-Access ANSI SCSI revision: 00
sd 2:0:0:0: Attached scsi removable disk sda
Vendor: Model: USB Card Reader Rev: 1.05
Type: Direct-Access ANSI SCSI revision: 00
sd 2:0:0:1: Attached scsi removable disk sdb
Vendor: Model: USB Card Reader Rev: 1.05
Type: Direct-Access ANSI SCSI revision: 00
sd 2:0:0:2: Attached scsi removable disk sdc
Vendor: Model: USB Card Reader Rev: 1.05
Type: Direct-Access ANSI SCSI revision: 00
sd 2:0:0:3: Attached scsi removable disk sdd
usb-storage: device scan complete
SCSI device sda: 510976 512-byte hdwr sectors (262 MB)
sda: Write Protect is off
sda: Mode Sense: 43 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 510976 512-byte hdwr sectors (262 MB)
sda: Write Protect is off
sda: Mode Sense: 43 00 00 00
sda: assuming drive cache: write through
sda: sda1
##############################
I hope, that this will help you to work on this point.
Chears & have a nice day.
--
Wolfgang Schnitker
Wolfgang Schnitker wrote:
> Dear Kernel Developers,
>
> I had some trouble with my usb devices, often showing a disconnect problem. I
> did some googleing and saw, that it is a less or more common problem.
>
> This problem is discussed in various internet sites.
>
> log from my machine:
>
> #############################
> usb 4-6: new high speed USB device using ehci_hcd and address 7
> usb 4-6: configuration #1 chosen from 1 choice
> hub 4-6:1.0: USB hub found
> hub 4-6:1.0: 4 ports detected
> usb 4-6.1: new full speed USB device using ehci_hcd and address 8
> usb 4-6.1: device descriptor read/64, error -32
> usb 4-6.1: device descriptor read/64, error -32
> usb 4-6.1: new full speed USB device using ehci_hcd and address 9
> usb 4-6.1: device descriptor read/64, error -110
> usb 4-6.1: device descriptor read/64, error -110
> usb 4-6.1: new full speed USB device using ehci_hcd and address 10
> usb 4-6.1: device not accepting address 10, error -32
> usb 4-6.1: new full speed USB device using ehci_hcd and address 11
> usb 4-6.1: device not accepting address 11, error -71
> usb 4-6: USB disconnect, address 7
> usb 4-6: new high speed USB device using ehci_hcd and address 12
> usb 4-6: configuration #1 chosen from 1 choice
> hub 4-6:1.0: USB hub found
> hub 4-6:1.0: 4 ports detected
> usb 4-6.1: new full speed USB device using ehci_hcd and address 13
> usb 4-6.1: device descriptor read/64, error -32
> usb 4-6.1: device descriptor read/64, error -32
> usb 4-6.1: new full speed USB device using ehci_hcd and address 14
> usb 4-6.1: device descriptor read/64, error -110
> usb 4-6.1: device descriptor read/64, error -71
> usb 4-6.1: new full speed USB device using ehci_hcd and address 15
> usb 4-6.1: device not accepting address 15, error -71
> usb 4-6.1: new full speed USB device using ehci_hcd and address 16
> usb 4-6.1: device not accepting address 16, error -71
> usb 4-6.1: new full speed USB device using ehci_hcd and address 17
> usb 4-6.1: configuration #1 chosen from 1 choice
> SCSI subsystem initialized
> Initializing USB Mass Storage driver...
> scsi0 : SCSI emulation for USB Mass Storage devices
> usbcore: registered new driver usb-storage
> usb-storage: device found at 17
> usb-storage: waiting for device to settle before scanning
> USB Mass Storage support registered.
> Vendor: Model: USB Card Reader Rev: 1.05
> Type: Direct-Access ANSI SCSI revision: 00
> Vendor: Model: USB Card Reader Rev: 1.05
> Type: Direct-Access ANSI SCSI revision: 00
> Vendor: Model: USB Card Reader Rev: 1.05
> Type: Direct-Access ANSI SCSI revision: 00
> Vendor: Model: USB Card Reader Rev: 1.05
> Type: Direct-Access ANSI SCSI revision: 00
> usb-storage: device scan complete
> sd 0:0:0:0: Attached scsi removable disk sda
> sd 0:0:0:1: Attached scsi removable disk sdb
> sd 0:0:0:2: Attached scsi removable disk sdc
> sd 0:0:0:3: Attached scsi removable disk sdd
> usb 4-6.1: reset full speed USB device using ehci_hcd and address 17
> usb 4-6.1: reset full speed USB device using ehci_hcd and address 17
> usb 4-6.1: reset full speed USB device using ehci_hcd and address 17
> usb 4-6.1: reset full speed USB device using ehci_hcd and address 17
> usb 4-6.1: reset full speed USB device using ehci_hcd and address 17
> usb 4-6.1: reset full speed USB device using ehci_hcd and address 17
> usb 4-6.1: reset full speed USB device using ehci_hcd and address 17
> usb 4-6.1: reset full speed USB device using ehci_hcd and address 17
> usb 4-6.1: USB disconnect, address 17
>
> #########################
>
> I have a solution/hint to solve this problem.
>
> In my case I had following NOT WORKING config:
>
> internal USB-Card PCI --> USB Hub --> Card Reader
> ( ali usb card, i-rocks hub, Phision cardreader)
>
> 00:08.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
> 00:08.1 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
> 00:08.2 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
> 00:08.3 USB Controller: ALi Corporation USB 2.0 Controller (rev 01)
>
> linux sets it up using:
>
> ehci --> ehci --> ehci (total usb 2.0 support)
>
> Bus 004 Device 028: ID 0d7d:0240 Phison Electronics Corp. I/O-Magic/Transcend
> 6-in-1 Card Reader
> Bus 004 Device 027: ID 05e3:0605 Genesys Logic, Inc. USB 2.0 Hub [ednet]
>
>
>
> but only the hub is a usb 2.0 compliant product. the card-reader is usb 1.1!!
>
> So i changed physically the hub back to a 1.1 device.
>
> and now linux sets this to
>
> ohci --> ohci --> ohci
>
> Bus 003 Device 011: ID 0d7d:0240 Phison Electronics Corp. I/O-Magic/Transcend
> 6-in-1 Card Reader
> Bus 003 Device 010: ID 03eb:3301 Atmel Corp. at43301 4-port Hub
>
>
> And this configuration works perfect, without any trouble any more.
>
> So in my opinion the problem is comming from ehci, which tries to set up a usb
> 1.1 device in a 2.0 mode. this results in severe timing problems, because the
> 1.1 device is too slow to handle this protocol, this results in a "dead"
> device from the point of view of the driver (no reaction). It disconnects the
> device and reconnects it again. It is only a problem, if you use a HUB
> between the USB Controller and the end device. I think we have to take care
> about the last device in the chain to set it up in the correct way.
I don't think that is what is going on. If you connect a USB 1.1 device
to a USB 2.0 hub, the USB 2.0 controller can still talk to it at high
speed using the EHCI controller, since the USB 2.0 hub has a transaction
translator for low and full speed devices. This is as designed and
should work (though it's possible there's a bug somewhere).
Are you sure that USB 2.0 hub is actually working properly, and can
supply adequate power for that card reader? (I've seen some crap hubs
that identify themselves as self-powered with 500mA per port, but a) it
still lists this even if the AC adapter is not plugged in and therefore
is actually bus-powered with far less power available, and b) even if it
was plugged in, the AC adapter is far too weak to actually be able to
supply this much power..)
--
Robert Hancock Saskatoon, SK, Canada
To email, remove "nospam" from [email protected]
Home Page: http://www.roberthancock.com/