Hi Vivek,
I can't seem to get the latest -mm (2.6.24-rc6-mm1) to boot with
kexec. It just gets stuck at "Starting new kernel".
It does boot normally when booted as the first kernel.
Any hints debugging? (x86 architecture)
--
regards,
Dhaval
On Fri, Dec 28, 2007 at 06:15:32PM +0530, Dhaval Giani wrote:
> Hi Vivek,
>
> I can't seem to get the latest -mm (2.6.24-rc6-mm1) to boot with
> kexec. It just gets stuck at "Starting new kernel".
>
> It does boot normally when booted as the first kernel.
>
> Any hints debugging? (x86 architecture)
I generally try few things.
- Specify earlyprintk= parameter for second kernel and see if control
is reaching to second kernel.
- Otherwise specify --console-serial parameter on "kexec -l" commandline
and it should display a message "I am in purgatory" on serial console.
This will just mean that control has reached at least till purgatory.
- If that also does not work, then most likely first kernel itself got
stuck somewhere and we need to put some printks in first kernel
to find out what's wrong.
Thanks
Vivek
On Fri, Dec 28, 2007 at 06:15:32PM +0530, Dhaval Giani wrote:
> Hi Vivek,
>
> I can't seem to get the latest -mm (2.6.24-rc6-mm1) to boot with
> kexec. It just gets stuck at "Starting new kernel".
>
> It does boot normally when booted as the first kernel.
>
> Any hints debugging? (x86 architecture)
>
> --
> regards,
> Dhaval
>
Out of curiosity, how are you booting the kexec kernel? Are you doing a kexec
-l, or a kexec -p, followed by a system panic? If its the later, what are you
doing to panic the system? sysrq-c, custom module executing explicit
crash-code, hang followed by nmi panic?
Regards
Neil
> _______________________________________________
> kexec mailing list
> [email protected]
> http://lists.infradead.org/mailman/listinfo/kexec
--
/***************************************************
*Neil Horman
*Software Engineer
*Red Hat, Inc.
*[email protected]
*gpg keyid: 1024D / 0x92A74FA1
*http://pgp.mit.edu
***************************************************/
On Fri, Dec 28, 2007 at 02:54:45PM -0500, Neil Horman wrote:
> On Fri, Dec 28, 2007 at 06:15:32PM +0530, Dhaval Giani wrote:
> > Hi Vivek,
> >
> > I can't seem to get the latest -mm (2.6.24-rc6-mm1) to boot with
> > kexec. It just gets stuck at "Starting new kernel".
> >
> > It does boot normally when booted as the first kernel.
> >
> > Any hints debugging? (x86 architecture)
> >
> > --
> > regards,
> > Dhaval
> >
> Out of curiosity, how are you booting the kexec kernel? Are you doing a kexec
> -l, or a kexec -p, followed by a system panic? If its the later, what are you
> doing to panic the system? sysrq-c, custom module executing explicit
> crash-code, hang followed by nmi panic?
>
kexec -l, followed by a normal reboot.
--
regards,
Dhaval
On Fri, Dec 28, 2007 at 09:27:39AM -0500, Vivek Goyal wrote:
> On Fri, Dec 28, 2007 at 06:15:32PM +0530, Dhaval Giani wrote:
> > Hi Vivek,
> >
> > I can't seem to get the latest -mm (2.6.24-rc6-mm1) to boot with
> > kexec. It just gets stuck at "Starting new kernel".
> >
> > It does boot normally when booted as the first kernel.
> >
> > Any hints debugging? (x86 architecture)
>
> I generally try few things.
>
> - Specify earlyprintk= parameter for second kernel and see if control
> is reaching to second kernel.
>
> - Otherwise specify --console-serial parameter on "kexec -l" commandline
> and it should display a message "I am in purgatory" on serial console.
> This will just mean that control has reached at least till purgatory.
>
Ok, so it reaches till here. I get "I'm in purgatory" on the console.
--
regards,
Dhaval
On Sat, Dec 29, 2007 at 11:11:13AM +0530, Dhaval Giani wrote:
> On Fri, Dec 28, 2007 at 09:27:39AM -0500, Vivek Goyal wrote:
> > On Fri, Dec 28, 2007 at 06:15:32PM +0530, Dhaval Giani wrote:
> > > Hi Vivek,
> > >
> > > I can't seem to get the latest -mm (2.6.24-rc6-mm1) to boot with
> > > kexec. It just gets stuck at "Starting new kernel".
> > >
> > > It does boot normally when booted as the first kernel.
> > >
> > > Any hints debugging? (x86 architecture)
> >
> > I generally try few things.
> >
> > - Specify earlyprintk= parameter for second kernel and see if control
> > is reaching to second kernel.
> >
> > - Otherwise specify --console-serial parameter on "kexec -l" commandline
> > and it should display a message "I am in purgatory" on serial console.
> > This will just mean that control has reached at least till purgatory.
> >
>
> Ok, so it reaches till here. I get "I'm in purgatory" on the console.
>
Ok. So it atleast reaches till purgatory. My hunch is that it also reaches
the second kernel but dies early in that kernel before any message can
be printed on screen.
Can you put some "outb()" messages on serial console in start_kernel() in
second kernel and see up to what point do you reach.
My 2.6.24-rc6-mm1 kernel panics during boot on 32bit box. Let me try it on
64 bit box.
Thanks
Vivek
On Sat, Dec 29, 2007 at 11:11:13AM +0530, Dhaval Giani wrote:
> On Fri, Dec 28, 2007 at 09:27:39AM -0500, Vivek Goyal wrote:
> > On Fri, Dec 28, 2007 at 06:15:32PM +0530, Dhaval Giani wrote:
> > > Hi Vivek,
> > >
> > > I can't seem to get the latest -mm (2.6.24-rc6-mm1) to boot with
> > > kexec. It just gets stuck at "Starting new kernel".
> > >
> > > It does boot normally when booted as the first kernel.
> > >
> > > Any hints debugging? (x86 architecture)
> >
> > I generally try few things.
> >
> > - Specify earlyprintk= parameter for second kernel and see if control
> > is reaching to second kernel.
> >
> > - Otherwise specify --console-serial parameter on "kexec -l" commandline
> > and it should display a message "I am in purgatory" on serial console.
> > This will just mean that control has reached at least till purgatory.
> >
>
> Ok, so it reaches till here. I get "I'm in purgatory" on the console.
One more thing. Is 2.6.24-rc6 working properly?
Thanks
Vivek
On Sat, Dec 29, 2007 at 11:11:13AM +0530, Dhaval Giani wrote:
> On Fri, Dec 28, 2007 at 09:27:39AM -0500, Vivek Goyal wrote:
> > On Fri, Dec 28, 2007 at 06:15:32PM +0530, Dhaval Giani wrote:
> > > Hi Vivek,
> > >
> > > I can't seem to get the latest -mm (2.6.24-rc6-mm1) to boot with
> > > kexec. It just gets stuck at "Starting new kernel".
> > >
> > > It does boot normally when booted as the first kernel.
> > >
> > > Any hints debugging? (x86 architecture)
> >
> > I generally try few things.
> >
> > - Specify earlyprintk= parameter for second kernel and see if control
> > is reaching to second kernel.
> >
> > - Otherwise specify --console-serial parameter on "kexec -l" commandline
> > and it should display a message "I am in purgatory" on serial console.
> > This will just mean that control has reached at least till purgatory.
> >
>
> Ok, so it reaches till here. I get "I'm in purgatory" on the console.
Hmm..., I just tried kexeing a 2.6.24-rc6-mm1 kernel from 2.6.24-rc6 on a
32bit box and it is working for me. That's a different thing 2.6.24-rc6-mm1
crashes later because of other problems.
Which kexec-tools are you using? I am using kexec-tools-testing-20071030.
Thanks
Vivek
2.6.24-rc6-mm1 boot BUG()
Creating block device nodes.
Creating root device.
end_request: I/O error, dev fd0, sector 0
input: ImPS/2 Generic Wheel Mouse as /class/input/input3
Mounting root filesystem.
end_request: I/O error, dev fd0, sector 0
------------[ cut here ]------------
kernel BUG at fs/buffer.c:1282!
invalid opcode: 0000 [#1] SMP
last sysfs file: /sys/block/hdc/dev
Modules linked in:
Pid: 1, comm: init Not tainted (2.6.24-rc6-mm1 #2)
EIP: 0060:[<c017e98b>] EFLAGS: 00010046 CPU: 0
EIP is at __find_get_block+0x1b/0x143
EAX: 00000086 EBX: 00000000 ECX: 00000400 EDX: 00000001
ESI: 00000001 EDI: f78bc000 EBP: f746e380 ESP: f7823c60
DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
Process init (pid: 1, ti=f7822000 task=f7820000 task.ti=f7822000)
Stack: 00000001 00000000 c014b17e 00000003 0000000a 0000c0d0 c16e2e00 c16e2ee0
f7177000 c16e2e00 c014bec4 00000000 00000001 f78bc000 f746e380 c017ecbd
00000400 00000001 00000000 00000000 00000000 0000c0d0 0000c0d0 c0560798
Call Trace:
[<c014b17e>] __rmqueue+0x13/0x174
[<c014bec4>] get_page_from_freelist+0x2d1/0x344
[<c017ecbd>] __getblk+0x21/0x295
[<c014bfb0>] __alloc_pages+0x67/0x2c5
[<c018089b>] __bread+0xa/0x78
[<c01c2353>] ext3_fill_super+0x138/0x1335
[<c0218d9e>] vsnprintf+0x407/0x445
[<c0218e52>] snprintf+0x1c/0x1f
[<c0194a0d>] disk_name+0x51/0x5b
[<c01665a1>] get_sb_bdev+0xce/0x10c
[<c014bfb0>] __alloc_pages+0x67/0x2c5
[<c0161c26>] __kmalloc+0x2f/0x9b
[<c01c0e06>] ext3_get_sb+0x12/0x16
[<c01c221b>] ext3_fill_super+0x0/0x1335
[<c01660ee>] vfs_kern_mount+0x39/0x72
[<c0166165>] do_kern_mount+0x2f/0xb4
[<c0176b00>] do_mount+0x5bf/0x621
[<c0175b12>] mntput_no_expire+0x11/0x85
[<c016c161>] link_path_walk+0x86/0x8f
[<c02d4e4a>] ide_disk_put+0x1c/0x27
[<c01672d9>] sys_stat64+0xf/0x23
[<c016534a>] put_filp+0x3c/0x9a
[<c014bc5c>] get_page_from_freelist+0x69/0x344
[<c0413309>] mutex_lock+0xb/0x1a
[<c014bfb0>] __alloc_pages+0x67/0x2c5
[<c01757b2>] copy_mount_options+0x26/0x109
[<c0176bcf>] sys_mount+0x6d/0xaa
[<c01038e6>] syscall_call+0x7/0xb
=======================
Code: 24 04 e8 49 f9 fc ff 89 d8 5b 5e 5b 5e 5f 5d c3 55 89 c5 57 56 53 83 ec 2c
89 4c 24 04 8b 4c 24 40 89 14 24 9c 58 f6 c4 02 75 04 <0f> 0b eb fe fa b8 00 bf
5f c0 31 ff 64 8b 15 10 a1 5f c0 01 c2
EIP: [<c017e98b>] __find_get_block+0x1b/0x143 SS:ESP 0068:f7823c60
---[ end trace bca1d6c3657fce65 ]---
Kernel panic - not syncing: Attempted to kill init!
WARNING: at arch/x86/kernel/smp_32.c:475 native_smp_send_reschedule()
Pid: 1, comm: init Tainted: G D 2.6.24-rc6-mm1 #2
[<c0115784>] native_smp_send_reschedule+0x2e/0x4d
[<c011cfae>] resched_task+0x56/0x58
[<c011e420>] resched_cpu+0x3c/0x49
[<c0120e22>] scheduler_tick+0x124/0x198
[<c012bff7>] update_process_times+0x3a/0x44
[<c013b380>] tick_sched_timer+0x73/0xb0
[<c0136c39>] hrtimer_interrupt+0x11f/0x1aa
[<c013b30d>] tick_sched_timer+0x0/0xb0
[<c01178d0>] smp_apic_timer_interrupt+0x69/0x78
[<c010434c>] apic_timer_interrupt+0x28/0x30
[<c041007b>] rpc_pipe_read+0xeb/0x100
[<c01243a4>] panic+0xc6/0xe6
[<c0126d8f>] do_exit+0x6b/0x5a7
[<c0104b74>] die+0x1c5/0x1ca
[<c0104cfd>] do_invalid_op+0x0/0x6b
[<c0104d5f>] do_invalid_op+0x62/0x6b
[<c017e98b>] __find_get_block+0x1b/0x143
[<c041437a>] error_code+0x72/0x78
[<c014007b>] sys_init_module+0x379/0x1602
[<c017e98b>] __find_get_block+0x1b/0x143
[<c014b17e>] __rmqueue+0x13/0x174
[<c014bec4>] get_page_from_freelist+0x2d1/0x344
[<c017ecbd>] __getblk+0x21/0x295
[<c014bfb0>] __alloc_pages+0x67/0x2c5
[<c018089b>] __bread+0xa/0x78
[<c01c2353>] ext3_fill_super+0x138/0x1335
[<c0218d9e>] vsnprintf+0x407/0x445
[<c0218e52>] snprintf+0x1c/0x1f
[<c0194a0d>] disk_name+0x51/0x5b
[<c01665a1>] get_sb_bdev+0xce/0x10c
[<c014bfb0>] __alloc_pages+0x67/0x2c5
[<c0161c26>] __kmalloc+0x2f/0x9b
[<c01c0e06>] ext3_get_sb+0x12/0x16
[<c01c221b>] ext3_fill_super+0x0/0x1335
[<c01660ee>] vfs_kern_mount+0x39/0x72
[<c0166165>] do_kern_mount+0x2f/0xb4
[<c0176b00>] do_mount+0x5bf/0x621
[<c0175b12>] mntput_no_expire+0x11/0x85
[<c016c161>] link_path_walk+0x86/0x8f
[<c02d4e4a>] ide_disk_put+0x1c/0x27
[<c01672d9>] sys_stat64+0xf/0x23
[<c016534a>] put_filp+0x3c/0x9a
[<c014bc5c>] get_page_from_freelist+0x69/0x344
[<c0413309>] mutex_lock+0xb/0x1a
[<c014bfb0>] __alloc_pages+0x67/0x2c5
[<c01757b2>] copy_mount_options+0x26/0x109
[<c0176bcf>] sys_mount+0x6d/0xaa
[<c01038e6>] syscall_call+0x7/0xb
=======================
WARNING: at arch/x86/kernel/smp_32.c:209 send_IPI_mask_bitmask()
Pid: 1, comm: init Tainted: G D 2.6.24-rc6-mm1 #2
[<c0115bbb>] send_IPI_mask_bitmask+0x33/0x80
[<c01157a1>] native_smp_send_reschedule+0x4b/0x4d
[<c011cfae>] resched_task+0x56/0x58
[<c011e420>] resched_cpu+0x3c/0x49
[<c0120e22>] scheduler_tick+0x124/0x198
[<c012bff7>] update_process_times+0x3a/0x44
[<c013b380>] tick_sched_timer+0x73/0xb0
[<c0136c39>] hrtimer_interrupt+0x11f/0x1aa
[<c013b30d>] tick_sched_timer+0x0/0xb0
[<c01178d0>] smp_apic_timer_interrupt+0x69/0x78
[<c010434c>] apic_timer_interrupt+0x28/0x30
[<c041007b>] rpc_pipe_read+0xeb/0x100
[<c01243a4>] panic+0xc6/0xe6
[<c0126d8f>] do_exit+0x6b/0x5a7
[<c0104b74>] die+0x1c5/0x1ca
[<c0104cfd>] do_invalid_op+0x0/0x6b
[<c0104d5f>] do_invalid_op+0x62/0x6b
[<c017e98b>] __find_get_block+0x1b/0x143
[<c041437a>] error_code+0x72/0x78
[<c014007b>] sys_init_module+0x379/0x1602
[<c017e98b>] __find_get_block+0x1b/0x143
[<c014b17e>] __rmqueue+0x13/0x174
[<c014bec4>] get_page_from_freelist+0x2d1/0x344
[<c017ecbd>] __getblk+0x21/0x295
[<c014bfb0>] __alloc_pages+0x67/0x2c5
[<c018089b>] __bread+0xa/0x78
[<c01c2353>] ext3_fill_super+0x138/0x1335
[<c0218d9e>] vsnprintf+0x407/0x445
[<c0218e52>] snprintf+0x1c/0x1f
[<c0194a0d>] disk_name+0x51/0x5b
[<c01665a1>] get_sb_bdev+0xce/0x10c
[<c014bfb0>] __alloc_pages+0x67/0x2c5
[<c0161c26>] __kmalloc+0x2f/0x9b
[<c01c0e06>] ext3_get_sb+0x12/0x16
[<c01c221b>] ext3_fill_super+0x0/0x1335
[<c01660ee>] vfs_kern_mount+0x39/0x72
[<c0166165>] do_kern_mount+0x2f/0xb4
[<c0176b00>] do_mount+0x5bf/0x621
[<c0175b12>] mntput_no_expire+0x11/0x85
[<c016c161>] link_path_walk+0x86/0x8f
[<c02d4e4a>] ide_disk_put+0x1c/0x27
[<c01672d9>] sys_stat64+0xf/0x23
[<c016534a>] put_filp+0x3c/0x9a
[<c014bc5c>] get_page_from_freelist+0x69/0x344
[<c0413309>] mutex_lock+0xb/0x1a
[<c014bfb0>] __alloc_pages+0x67/0x2c5
[<c01757b2>] copy_mount_options+0x26/0x109
[<c0176bcf>] sys_mount+0x6d/0xaa
[<c01038e6>] syscall_call+0x7/0xb
=======================
On Mon, Dec 31, 2007 at 10:06:58AM -0500, Vivek Goyal wrote:
> On Sat, Dec 29, 2007 at 11:11:13AM +0530, Dhaval Giani wrote:
> > On Fri, Dec 28, 2007 at 09:27:39AM -0500, Vivek Goyal wrote:
> > > On Fri, Dec 28, 2007 at 06:15:32PM +0530, Dhaval Giani wrote:
> > > > Hi Vivek,
> > > >
> > > > I can't seem to get the latest -mm (2.6.24-rc6-mm1) to boot with
> > > > kexec. It just gets stuck at "Starting new kernel".
> > > >
> > > > It does boot normally when booted as the first kernel.
> > > >
> > > > Any hints debugging? (x86 architecture)
> > >
> > > I generally try few things.
> > >
> > > - Specify earlyprintk= parameter for second kernel and see if control
> > > is reaching to second kernel.
> > >
> > > - Otherwise specify --console-serial parameter on "kexec -l" commandline
> > > and it should display a message "I am in purgatory" on serial console.
> > > This will just mean that control has reached at least till purgatory.
> > >
> >
> > Ok, so it reaches till here. I get "I'm in purgatory" on the console.
> >
>
> Ok. So it atleast reaches till purgatory. My hunch is that it also reaches
> the second kernel but dies early in that kernel before any message can
> be printed on screen.
>
> Can you put some "outb()" messages on serial console in start_kernel() in
> second kernel and see up to what point do you reach.
>
> My 2.6.24-rc6-mm1 kernel panics during boot on 32bit box. Let me try it on
> 64 bit box.
>
Apply the hotfixes :-)
--
regards,
Dhaval
On Mon, Dec 31, 2007 at 10:08:43AM -0500, Vivek Goyal wrote:
> On Sat, Dec 29, 2007 at 11:11:13AM +0530, Dhaval Giani wrote:
> > On Fri, Dec 28, 2007 at 09:27:39AM -0500, Vivek Goyal wrote:
> > > On Fri, Dec 28, 2007 at 06:15:32PM +0530, Dhaval Giani wrote:
> > > > Hi Vivek,
> > > >
> > > > I can't seem to get the latest -mm (2.6.24-rc6-mm1) to boot with
> > > > kexec. It just gets stuck at "Starting new kernel".
> > > >
> > > > It does boot normally when booted as the first kernel.
> > > >
> > > > Any hints debugging? (x86 architecture)
> > >
> > > I generally try few things.
> > >
> > > - Specify earlyprintk= parameter for second kernel and see if control
> > > is reaching to second kernel.
> > >
> > > - Otherwise specify --console-serial parameter on "kexec -l" commandline
> > > and it should display a message "I am in purgatory" on serial console.
> > > This will just mean that control has reached at least till purgatory.
> > >
> >
> > Ok, so it reaches till here. I get "I'm in purgatory" on the console.
>
> One more thing. Is 2.6.24-rc6 working properly?
>
2.6.24-rc5 boots, so does 2.6.24-rc5-mm1. 2.6.24-rc6 does not boot, nor
does 2.6.24-rc6-mm1. Its a regression.
i will add more outbs and respond back and try a bisect if that does not
help.
Thanks
--
regards,
Dhaval
On Thursday, 3 of January 2008, Dhaval Giani wrote:
> On Mon, Dec 31, 2007 at 10:08:43AM -0500, Vivek Goyal wrote:
> > On Sat, Dec 29, 2007 at 11:11:13AM +0530, Dhaval Giani wrote:
> > > On Fri, Dec 28, 2007 at 09:27:39AM -0500, Vivek Goyal wrote:
> > > > On Fri, Dec 28, 2007 at 06:15:32PM +0530, Dhaval Giani wrote:
> > > > > Hi Vivek,
> > > > >
> > > > > I can't seem to get the latest -mm (2.6.24-rc6-mm1) to boot with
> > > > > kexec. It just gets stuck at "Starting new kernel".
> > > > >
> > > > > It does boot normally when booted as the first kernel.
> > > > >
> > > > > Any hints debugging? (x86 architecture)
> > > >
> > > > I generally try few things.
> > > >
> > > > - Specify earlyprintk= parameter for second kernel and see if control
> > > > is reaching to second kernel.
> > > >
> > > > - Otherwise specify --console-serial parameter on "kexec -l" commandline
> > > > and it should display a message "I am in purgatory" on serial console.
> > > > This will just mean that control has reached at least till purgatory.
> > > >
> > >
> > > Ok, so it reaches till here. I get "I'm in purgatory" on the console.
> >
> > One more thing. Is 2.6.24-rc6 working properly?
> >
>
> 2.6.24-rc5 boots, so does 2.6.24-rc5-mm1. 2.6.24-rc6 does not boot, nor
> does 2.6.24-rc6-mm1. Its a regression.
Added to the list of reported regressions as:
http://bugzilla.kernel.org/show_bug.cgi?id=9682
Thanks,
Rafael
On Thu, Jan 03, 2008 at 10:42:00PM +0100, Rafael J. Wysocki wrote:
> On Thursday, 3 of January 2008, Dhaval Giani wrote:
> > On Mon, Dec 31, 2007 at 10:08:43AM -0500, Vivek Goyal wrote:
> > > On Sat, Dec 29, 2007 at 11:11:13AM +0530, Dhaval Giani wrote:
> > > > On Fri, Dec 28, 2007 at 09:27:39AM -0500, Vivek Goyal wrote:
> > > > > On Fri, Dec 28, 2007 at 06:15:32PM +0530, Dhaval Giani wrote:
> > > > > > Hi Vivek,
> > > > > >
> > > > > > I can't seem to get the latest -mm (2.6.24-rc6-mm1) to boot with
> > > > > > kexec. It just gets stuck at "Starting new kernel".
> > > > > >
> > > > > > It does boot normally when booted as the first kernel.
> > > > > >
> > > > > > Any hints debugging? (x86 architecture)
> > > > >
> > > > > I generally try few things.
> > > > >
> > > > > - Specify earlyprintk= parameter for second kernel and see if control
> > > > > is reaching to second kernel.
> > > > >
> > > > > - Otherwise specify --console-serial parameter on "kexec -l" commandline
> > > > > and it should display a message "I am in purgatory" on serial console.
> > > > > This will just mean that control has reached at least till purgatory.
> > > > >
> > > >
> > > > Ok, so it reaches till here. I get "I'm in purgatory" on the console.
> > >
> > > One more thing. Is 2.6.24-rc6 working properly?
> > >
> >
> > 2.6.24-rc5 boots, so does 2.6.24-rc5-mm1. 2.6.24-rc6 does not boot, nor
> > does 2.6.24-rc6-mm1. Its a regression.
>
> Added to the list of reported regressions as:
> http://bugzilla.kernel.org/show_bug.cgi?id=9682
>
I've no clue what I managed to do wrong last night, probably tried to boot
2.6.24-rc6-mm1 thinking it was 2.6.24-rc6. 2.6.24-rc6 boots, but -mm
does not. Sorry for the noise.
With the help of the outbs I have figured out that it is dying somewhere
in setup_memory(). Will look deeper into it.
--
regards,
Dhaval
On Fri, Jan 04, 2008 at 05:58:16PM +0530, Dhaval Giani wrote:
> On Thu, Jan 03, 2008 at 10:42:00PM +0100, Rafael J. Wysocki wrote:
> > On Thursday, 3 of January 2008, Dhaval Giani wrote:
> > > On Mon, Dec 31, 2007 at 10:08:43AM -0500, Vivek Goyal wrote:
> > > > On Sat, Dec 29, 2007 at 11:11:13AM +0530, Dhaval Giani wrote:
> > > > > On Fri, Dec 28, 2007 at 09:27:39AM -0500, Vivek Goyal wrote:
> > > > > > On Fri, Dec 28, 2007 at 06:15:32PM +0530, Dhaval Giani wrote:
> > > > > > > Hi Vivek,
> > > > > > >
>
> I've no clue what I managed to do wrong last night, probably tried to boot
> 2.6.24-rc6-mm1 thinking it was 2.6.24-rc6. 2.6.24-rc6 boots, but -mm
> does not. Sorry for the noise.
>
So I went ahead and bisected -mm, and the culprit is git-x86. It boots
fine before it, but with git-x86 applied, it fails to boot.
Ingo/Thomas, could you please point me to the git-x86 tree so that I can
bisect it? (with instructions on how to pull the -mm branch, I managed
to pull the master branch, but not the -mm branch)
--
regards,
Dhaval
On Friday, 4 of January 2008, Dhaval Giani wrote:
> On Thu, Jan 03, 2008 at 10:42:00PM +0100, Rafael J. Wysocki wrote:
> > On Thursday, 3 of January 2008, Dhaval Giani wrote:
> > > On Mon, Dec 31, 2007 at 10:08:43AM -0500, Vivek Goyal wrote:
> > > > On Sat, Dec 29, 2007 at 11:11:13AM +0530, Dhaval Giani wrote:
> > > > > On Fri, Dec 28, 2007 at 09:27:39AM -0500, Vivek Goyal wrote:
> > > > > > On Fri, Dec 28, 2007 at 06:15:32PM +0530, Dhaval Giani wrote:
> > > > > > > Hi Vivek,
> > > > > > >
> > > > > > > I can't seem to get the latest -mm (2.6.24-rc6-mm1) to boot with
> > > > > > > kexec. It just gets stuck at "Starting new kernel".
> > > > > > >
> > > > > > > It does boot normally when booted as the first kernel.
> > > > > > >
> > > > > > > Any hints debugging? (x86 architecture)
> > > > > >
> > > > > > I generally try few things.
> > > > > >
> > > > > > - Specify earlyprintk= parameter for second kernel and see if control
> > > > > > is reaching to second kernel.
> > > > > >
> > > > > > - Otherwise specify --console-serial parameter on "kexec -l" commandline
> > > > > > and it should display a message "I am in purgatory" on serial console.
> > > > > > This will just mean that control has reached at least till purgatory.
> > > > > >
> > > > >
> > > > > Ok, so it reaches till here. I get "I'm in purgatory" on the console.
> > > >
> > > > One more thing. Is 2.6.24-rc6 working properly?
> > > >
> > >
> > > 2.6.24-rc5 boots, so does 2.6.24-rc5-mm1. 2.6.24-rc6 does not boot, nor
> > > does 2.6.24-rc6-mm1. Its a regression.
> >
> > Added to the list of reported regressions as:
> > http://bugzilla.kernel.org/show_bug.cgi?id=9682
> >
>
> I've no clue what I managed to do wrong last night, probably tried to boot
> 2.6.24-rc6-mm1 thinking it was 2.6.24-rc6. 2.6.24-rc6 boots, but -mm
> does not. Sorry for the noise.
Dropped from the regression list and changed the bugzilla entry to an -mm bug.
Thanks,
Rafael
On Fri, 4 Jan 2008 21:24:15 +0530 Dhaval Giani <[email protected]> wrote:
> On Fri, Jan 04, 2008 at 05:58:16PM +0530, Dhaval Giani wrote:
> > On Thu, Jan 03, 2008 at 10:42:00PM +0100, Rafael J. Wysocki wrote:
> > > On Thursday, 3 of January 2008, Dhaval Giani wrote:
> > > > On Mon, Dec 31, 2007 at 10:08:43AM -0500, Vivek Goyal wrote:
> > > > > On Sat, Dec 29, 2007 at 11:11:13AM +0530, Dhaval Giani wrote:
> > > > > > On Fri, Dec 28, 2007 at 09:27:39AM -0500, Vivek Goyal wrote:
> > > > > > > On Fri, Dec 28, 2007 at 06:15:32PM +0530, Dhaval Giani wrote:
> > > > > > > > Hi Vivek,
> > > > > > > >
> >
> > I've no clue what I managed to do wrong last night, probably tried to boot
> > 2.6.24-rc6-mm1 thinking it was 2.6.24-rc6. 2.6.24-rc6 boots, but -mm
> > does not. Sorry for the noise.
> >
>
> So I went ahead and bisected -mm, and the culprit is git-x86. It boots
> fine before it, but with git-x86 applied, it fails to boot.
>
> Ingo/Thomas, could you please point me to the git-x86 tree so that I can
> bisect it?
Every git-foo.patch in -mm identifies where it came from in its changelog.
The first few lines of
ftp://ftp.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.24-rc6/2.6.24-rc6-mm1/broken-out/git-x86.patch
are:
GIT 27197ba67cbaa0e22598a10c82b10dacb1309ed8 irqs_disabled
git+ssh://master.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86.git#mm
I'm not sure what the "irqs_disabled\n\n" is doing there: maybe I added it
by mistake. 2.6.24-rc5-mm1 correctly had
GIT b668e28b74558b3a8277b5fde363ae5f803b36f0 git+ssh://master.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86.git#mm
But still. The git URL is always there.
* Dhaval Giani <[email protected]> wrote:
> So I went ahead and bisected -mm, and the culprit is git-x86. It boots
> fine before it, but with git-x86 applied, it fails to boot.
>
> Ingo/Thomas, could you please point me to the git-x86 tree so that I
> can bisect it? (with instructions on how to pull the -mm branch, I
> managed to pull the master branch, but not the -mm branch)
sure:
--------------{ x86.git instructions }---------->
git-clone git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git linux-2.6.git
cd linux-2.6.git
git-branch x86
git-checkout x86
git-pull git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86.git mm
git-log HEAD@{1}.. # see what's in #mm
(do subsequent pulls via "git-pull --force", as we frequently rebase the
git tree. NOTE: this might override your own local changes, so do this
only if you dont mind about losing thse changes in that tree.)
On Sun, Jan 06, 2008 at 02:37:29PM +0100, Ingo Molnar wrote:
>
> * Dhaval Giani <[email protected]> wrote:
>
> > So I went ahead and bisected -mm, and the culprit is git-x86. It boots
> > fine before it, but with git-x86 applied, it fails to boot.
> >
> > Ingo/Thomas, could you please point me to the git-x86 tree so that I
> > can bisect it? (with instructions on how to pull the -mm branch, I
> > managed to pull the master branch, but not the -mm branch)
>
> sure:
>
> --------------{ x86.git instructions }---------->
>
> git-clone git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git linux-2.6.git
> cd linux-2.6.git
> git-branch x86
> git-checkout x86
> git-pull git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86.git mm
> git-log HEAD@{1}.. # see what's in #mm
>
Thanks for the instructions. I went ahead and did the bisect, and
commit 7dd838ea7afa42a8840cf0e262d5892346ecf379
Author: H. Peter Anvin <[email protected]>
Date: Sat Jan 5 13:27:04 2008 +0100
is the first bad commit.
git bisect log
dhaval@kernel:~/mm$ git bisect log
git-bisect start
# good: [439f61b9f9ebbf84fb7e6b3539fc3794e046bbb9] Merge
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
git-bisect good 439f61b9f9ebbf84fb7e6b3539fc3794e046bbb9
# bad: [5c9b01f1566f4989bb732a46c9a9c86f3e7ef9ae] x86: unregister PIT
clocksource when PIT is disabled
git-bisect bad 5c9b01f1566f4989bb732a46c9a9c86f3e7ef9ae
# good: [203bcdc3d2725751e4dc0e3749edbab3c8bf9132] move switch_to macro
to system.h
git-bisect good 203bcdc3d2725751e4dc0e3749edbab3c8bf9132
# good: [81886a1b16eec7a27f3ec94f06f585685ad08bf2] x86: i387 renaming
git-bisect good 81886a1b16eec7a27f3ec94f06f585685ad08bf2
# bad: [fc0ed2251da6ef8ad3295a02b39bed9859dc0cfc] x86: unify
arch/x86/kernel/Makefile(s)
git-bisect bad fc0ed2251da6ef8ad3295a02b39bed9859dc0cfc
# good: [6fa16686ee2b0cc6b02a59671ecb9d4c85beae64] change assembly
definition of paravirt_patch_site
git-bisect good 6fa16686ee2b0cc6b02a59671ecb9d4c85beae64
# bad: [1184caa02fcc2ecd780b145f4c69cc4484a8cde4] git-x86:
arch/x86/math-emu/errors.c: fix printk warnings
git-bisect bad 1184caa02fcc2ecd780b145f4c69cc4484a8cde4
# good: [e8189d0ca1970578f4b28f92928581313633be5a] x86_64 patching
functions
git-bisect good e8189d0ca1970578f4b28f92928581313633be5a
# bad: [7dd838ea7afa42a8840cf0e262d5892346ecf379] i386: handle an initrd
in highmem
git-bisect bad 7dd838ea7afa42a8840cf0e262d5892346ecf379
# good: [8cff7d1301d37b15add1dabe6ac8a92e6c0a1c7f] i386 EFI runtime
service support: fixes in sync with x86_64 support
git-bisect good 8cff7d1301d37b15add1dabe6ac8a92e6c0a1c7f
# good: [ac3836d03c718a553634ff21c1157bb823567f4f] x86:
arch/x86/kernel/setup_32.c whitespace fixes
git-bisect good ac3836d03c718a553634ff21c1157bb823567f4f
--
regards,
Dhaval
> commit 7dd838ea7afa42a8840cf0e262d5892346ecf379
> Author: H. Peter Anvin <[email protected]>
> Date: Sat Jan 5 13:27:04 2008 +0100
>
sorry, forgot the subject, it is
i386: handle an initrd in highmem
--
regards,
Dhaval
Dhaval Giani wrote:
> Hi Vivek,
>
> I can't seem to get the latest -mm (2.6.24-rc6-mm1) to boot with
> kexec. It just gets stuck at "Starting new kernel".
>
> It does boot normally when booted as the first kernel.
>
> Any hints debugging? (x86 architecture)
>
Hi Dhaval,
Could you give more details of your setup? I'm trying to figure out
exactly what it is in kexec that goes goofy, but there seems to be an
enormous number of codepaths, all different, depending on things like
which kind of kernel. The more closely I can replicate your failure,
the quicker I should be able to locate the problem.
-hpa
On Mon, Jan 07, 2008 at 09:43:38AM -0800, H. Peter Anvin wrote:
> Dhaval Giani wrote:
>> Hi Vivek,
>>
>> I can't seem to get the latest -mm (2.6.24-rc6-mm1) to boot with
>> kexec. It just gets stuck at "Starting new kernel".
>>
>> It does boot normally when booted as the first kernel.
>>
>> Any hints debugging? (x86 architecture)
>>
>
> Hi Dhaval,
>
> Could you give more details of your setup? I'm trying to figure out
> exactly what it is in kexec that goes goofy, but there seems to be an
> enormous number of codepaths, all different, depending on things like which
> kind of kernel. The more closely I can replicate your failure, the quicker
> I should be able to locate the problem.
>
Hi,
sure,
[root@llm11 ~]# cat /proc/cpuinfo
processor : 0
vendor_id : GenuineIntel
cpu family : 15
model : 2
model name : Intel(R) Xeon(TM) MP CPU 2.50GHz
stepping : 5
cpu MHz : 2500.000
cache size : 1024 KB
physical id : 0
siblings : 2
core id : 0
cpu cores : 1
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe pebs
bts sync_rdtsc cid xtpr
bogomips : 4983.50
clflush size : 64
processor : 1
vendor_id : GenuineIntel
cpu family : 15
model : 2
model name : Intel(R) Xeon(TM) MP CPU 2.50GHz
stepping : 5
cpu MHz : 2500.000
cache size : 1024 KB
physical id : 0
siblings : 2
core id : 0
cpu cores : 1
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe pebs
bts sync_rdtsc cid xtpr
bogomips : 4976.76
clflush size : 64
processor : 2
vendor_id : GenuineIntel
cpu family : 15
model : 2
model name : Intel(R) Xeon(TM) MP CPU 2.50GHz
stepping : 5
cpu MHz : 2500.000
cache size : 1024 KB
physical id : 1
siblings : 2
core id : 0
cpu cores : 1
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe pebs
bts sync_rdtsc cid xtpr
bogomips : 4976.89
clflush size : 64
processor : 3
vendor_id : GenuineIntel
cpu family : 15
model : 2
model name : Intel(R) Xeon(TM) MP CPU 2.50GHz
stepping : 5
cpu MHz : 2500.000
cache size : 1024 KB
physical id : 1
siblings : 2
core id : 0
cpu cores : 1
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe pebs
bts sync_rdtsc cid xtpr
bogomips : 4976.68
clflush size : 64
processor : 4
vendor_id : GenuineIntel
cpu family : 15
model : 2
model name : Intel(R) Xeon(TM) MP CPU 2.50GHz
stepping : 5
cpu MHz : 2500.000
cache size : 1024 KB
physical id : 2
siblings : 2
core id : 0
cpu cores : 1
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe pebs
bts sync_rdtsc cid xtpr
bogomips : 4976.79
clflush size : 64
processor : 5
vendor_id : GenuineIntel
cpu family : 15
model : 2
model name : Intel(R) Xeon(TM) MP CPU 2.50GHz
stepping : 5
cpu MHz : 2500.000
cache size : 1024 KB
physical id : 2
siblings : 2
core id : 0
cpu cores : 1
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe pebs
bts sync_rdtsc cid xtpr
bogomips : 4976.60
clflush size : 64
processor : 6
vendor_id : GenuineIntel
cpu family : 15
model : 2
model name : Intel(R) Xeon(TM) MP CPU 2.50GHz
stepping : 5
cpu MHz : 2500.000
cache size : 1024 KB
physical id : 3
siblings : 2
core id : 0
cpu cores : 1
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe pebs
bts sync_rdtsc cid xtpr
bogomips : 4976.46
clflush size : 64
processor : 7
vendor_id : GenuineIntel
cpu family : 15
model : 2
model name : Intel(R) Xeon(TM) MP CPU 2.50GHz
stepping : 5
cpu MHz : 2500.000
cache size : 1024 KB
physical id : 3
siblings : 2
core id : 0
cpu cores : 1
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe pebs
bts sync_rdtsc cid xtpr
bogomips : 4976.50
clflush size : 64
[root@llm11 ~]#
.config
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.24-rc7
# Mon Jan 7 18:19:17 2008
#
# CONFIG_64BIT is not set
CONFIG_X86_32=y
# CONFIG_X86_64 is not set
CONFIG_X86=y
# CONFIG_GENERIC_LOCKBREAK is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CMOS_UPDATE=y
CONFIG_CLOCKSOURCE_WATCHDOG=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_SEMAPHORE_SLEEPERS=y
CONFIG_MMU=y
CONFIG_ZONE_DMA=y
CONFIG_QUICKLIST=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
CONFIG_GENERIC_BUG=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_HWEIGHT=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
CONFIG_DMI=y
# CONFIG_RWSEM_GENERIC_SPINLOCK is not set
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
# CONFIG_ARCH_HAS_ILOG2_U32 is not set
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_GENERIC_CALIBRATE_DELAY=y
# CONFIG_GENERIC_TIME_VSYSCALL is not set
CONFIG_ARCH_SUPPORTS_OPROFILE=y
# CONFIG_ZONE_DMA32 is not set
CONFIG_ARCH_POPULATES_NODE_MAP=y
# CONFIG_AUDIT_ARCH is not set
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_GENERIC_PENDING_IRQ=y
CONFIG_PM_CPUINIT=y
CONFIG_X86_SMP=y
CONFIG_X86_32_SMP=y
CONFIG_X86_HT=y
CONFIG_X86_BIOS_REBOOT=y
CONFIG_X86_TRAMPOLINE=y
CONFIG_KTIME_SCALAR=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
# General setup
#
CONFIG_EXPERIMENTAL=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
# CONFIG_USER_NS is not set
# CONFIG_PID_NS is not set
CONFIG_AUDIT=y
CONFIG_AUDITSYSCALL=y
CONFIG_AUDIT_TREE=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=15
CONFIG_CGROUPS=y
# CONFIG_CGROUP_DEBUG is not set
# CONFIG_CGROUP_NS is not set
# CONFIG_CPUSETS is not set
CONFIG_FAIR_GROUP_SCHED=y
# CONFIG_FAIR_USER_SCHED is not set
CONFIG_FAIR_CGROUP_SCHED=y
# CONFIG_CGROUP_CPUACCT is not set
CONFIG_SYSFS_DEPRECATED=y
CONFIG_RELAY=y
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
# CONFIG_EMBEDDED is not set
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
CONFIG_KALLSYMS_ALL=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
# CONFIG_KMOD is not set
CONFIG_STOP_MACHINE=y
CONFIG_BLOCK=y
CONFIG_LBD=y
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
# CONFIG_BLK_DEV_BSG is not set
#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
CONFIG_DEFAULT_AS=y
# CONFIG_DEFAULT_DEADLINE is not set
# CONFIG_DEFAULT_CFQ is not set
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="anticipatory"
#
# Processor type and features
#
# CONFIG_TICK_ONESHOT is not set
# CONFIG_NO_HZ is not set
# CONFIG_HIGH_RES_TIMERS is not set
CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
CONFIG_SMP=y
# CONFIG_X86_PC is not set
# CONFIG_X86_ELAN is not set
# CONFIG_X86_VOYAGER is not set
# CONFIG_X86_NUMAQ is not set
# CONFIG_X86_SUMMIT is not set
# CONFIG_X86_BIGSMP is not set
# CONFIG_X86_VISWS is not set
CONFIG_X86_GENERICARCH=y
# CONFIG_X86_ES7000 is not set
# CONFIG_X86_RDC321X is not set
# CONFIG_X86_VSMP is not set
CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
# CONFIG_PARAVIRT_GUEST is not set
CONFIG_ACPI_SRAT=y
CONFIG_HAVE_ARCH_PARSE_SRAT=y
CONFIG_X86_SUMMIT_NUMA=y
CONFIG_X86_CYCLONE_TIMER=y
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMII is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUMM is not set
CONFIG_MPENTIUM4=y
# CONFIG_MK6 is not set
# CONFIG_MK7 is not set
# CONFIG_MK8 is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MEFFICEON is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MGEODEGX1 is not set
# CONFIG_MGEODE_LX is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
# CONFIG_MVIAC7 is not set
# CONFIG_MPSC is not set
# CONFIG_MCORE2 is not set
# CONFIG_GENERIC_CPU is not set
CONFIG_X86_GENERIC=y
CONFIG_X86_CMPXCHG=y
CONFIG_X86_L1_CACHE_SHIFT=7
CONFIG_X86_XADD=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_INTEL_USERCOPY=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_TSC=y
CONFIG_X86_CMOV=y
CONFIG_X86_MINIMUM_CPU_FAMILY=4
CONFIG_X86_DEBUGCTLMSR=y
CONFIG_HPET_TIMER=y
CONFIG_HPET_EMULATE_RTC=y
CONFIG_NR_CPUS=32
CONFIG_SCHED_SMT=y
CONFIG_SCHED_MC=y
# CONFIG_PREEMPT_NONE is not set
CONFIG_PREEMPT_VOLUNTARY=y
# CONFIG_PREEMPT is not set
CONFIG_PREEMPT_BKL=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_MCE=y
CONFIG_X86_MCE_NONFATAL=y
CONFIG_X86_MCE_P4THERMAL=y
CONFIG_VM86=y
# CONFIG_TOSHIBA is not set
# CONFIG_I8K is not set
# CONFIG_X86_REBOOTFIXUPS is not set
CONFIG_MICROCODE=y
CONFIG_MICROCODE_OLD_INTERFACE=y
CONFIG_X86_MSR=y
CONFIG_X86_CPUID=y
# CONFIG_NOHIGHMEM is not set
# CONFIG_HIGHMEM4G is not set
CONFIG_HIGHMEM64G=y
CONFIG_PAGE_OFFSET=0xC0000000
CONFIG_HIGHMEM=y
CONFIG_X86_PAE=y
CONFIG_NUMA=y
CONFIG_NODES_SHIFT=3
CONFIG_HAVE_ARCH_BOOTMEM_NODE=y
CONFIG_ARCH_HAVE_MEMORY_PRESENT=y
CONFIG_NEED_NODE_MEMMAP_SIZE=y
CONFIG_HAVE_ARCH_ALLOC_REMAP=y
CONFIG_ARCH_DISCONTIGMEM_ENABLE=y
CONFIG_ARCH_DISCONTIGMEM_DEFAULT=y
CONFIG_ARCH_SPARSEMEM_ENABLE=y
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_SELECT_MEMORY_MODEL=y
# CONFIG_FLATMEM_MANUAL is not set
CONFIG_DISCONTIGMEM_MANUAL=y
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_DISCONTIGMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_NEED_MULTIPLE_NODES=y
CONFIG_HAVE_MEMORY_PRESENT=y
CONFIG_SPARSEMEM_STATIC=y
# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_MIGRATION=y
CONFIG_RESOURCES_64BIT=y
CONFIG_ZONE_DMA_FLAG=1
CONFIG_BOUNCE=y
CONFIG_NR_QUICK=1
CONFIG_VIRT_TO_BUS=y
# CONFIG_HIGHPTE is not set
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
# CONFIG_EFI is not set
# CONFIG_IRQBALANCE is not set
CONFIG_BOOT_IOREMAP=y
CONFIG_SECCOMP=y
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
# CONFIG_HZ_300 is not set
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
CONFIG_KEXEC=y
# CONFIG_CRASH_DUMP is not set
CONFIG_PHYSICAL_START=0x100000
# CONFIG_RELOCATABLE is not set
CONFIG_PHYSICAL_ALIGN=0x100000
CONFIG_HOTPLUG_CPU=y
CONFIG_COMPAT_VDSO=y
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
# CONFIG_HAVE_ARCH_EARLY_PFN_TO_NID is not set
#
# Power management options
#
CONFIG_PM=y
CONFIG_PM_LEGACY=y
CONFIG_PM_DEBUG=y
# CONFIG_PM_VERBOSE is not set
# CONFIG_PM_TRACE is not set
CONFIG_PM_SLEEP_SMP=y
CONFIG_PM_SLEEP=y
CONFIG_SUSPEND_SMP_POSSIBLE=y
CONFIG_SUSPEND=y
CONFIG_HIBERNATION_SMP_POSSIBLE=y
# CONFIG_HIBERNATION is not set
CONFIG_ACPI=y
CONFIG_ACPI_SLEEP=y
# CONFIG_ACPI_PROCFS is not set
CONFIG_ACPI_PROCFS_POWER=y
CONFIG_ACPI_PROC_EVENT=y
CONFIG_ACPI_AC=y
CONFIG_ACPI_BATTERY=y
CONFIG_ACPI_BUTTON=y
CONFIG_ACPI_FAN=y
# CONFIG_ACPI_DOCK is not set
CONFIG_ACPI_PROCESSOR=y
CONFIG_ACPI_HOTPLUG_CPU=y
CONFIG_ACPI_THERMAL=y
CONFIG_ACPI_NUMA=y
# CONFIG_ACPI_ASUS is not set
# CONFIG_ACPI_TOSHIBA is not set
CONFIG_ACPI_BLACKLIST_YEAR=2001
CONFIG_ACPI_DEBUG=y
# CONFIG_ACPI_DEBUG_FUNC_TRACE is not set
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_SYSTEM=y
CONFIG_X86_PM_TIMER=y
CONFIG_ACPI_CONTAINER=y
# CONFIG_ACPI_SBS is not set
# CONFIG_APM is not set
#
# CPU Frequency scaling
#
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_TABLE=y
CONFIG_CPU_FREQ_DEBUG=y
CONFIG_CPU_FREQ_STAT=y
CONFIG_CPU_FREQ_STAT_DETAILS=y
CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
# CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND is not set
# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_POWERSAVE=y
CONFIG_CPU_FREQ_GOV_USERSPACE=y
CONFIG_CPU_FREQ_GOV_ONDEMAND=y
CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y
#
# CPUFreq processor drivers
#
# CONFIG_X86_ACPI_CPUFREQ is not set
# CONFIG_X86_POWERNOW_K6 is not set
# CONFIG_X86_POWERNOW_K7 is not set
# CONFIG_X86_POWERNOW_K8 is not set
# CONFIG_X86_GX_SUSPMOD is not set
# CONFIG_X86_SPEEDSTEP_CENTRINO is not set
# CONFIG_X86_SPEEDSTEP_ICH is not set
# CONFIG_X86_SPEEDSTEP_SMI is not set
CONFIG_X86_P4_CLOCKMOD=y
# CONFIG_X86_CPUFREQ_NFORCE2 is not set
# CONFIG_X86_LONGRUN is not set
# CONFIG_X86_LONGHAUL is not set
# CONFIG_X86_E_POWERSAVER is not set
#
# shared options
#
CONFIG_X86_SPEEDSTEP_LIB=y
# CONFIG_CPU_IDLE is not set
#
# Bus options (PCI etc.)
#
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GOMMCONFIG is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
CONFIG_PCI_DOMAINS=y
# CONFIG_PCIEPORTBUS is not set
CONFIG_ARCH_SUPPORTS_MSI=y
CONFIG_PCI_MSI=y
CONFIG_PCI_LEGACY=y
# CONFIG_PCI_DEBUG is not set
CONFIG_HT_IRQ=y
CONFIG_ISA_DMA_API=y
# CONFIG_ISA is not set
# CONFIG_MCA is not set
# CONFIG_SCx200 is not set
CONFIG_K8_NB=y
# CONFIG_PCCARD is not set
# CONFIG_HOTPLUG_PCI is not set
#
# Executable file formats / Emulations
#
CONFIG_BINFMT_ELF=y
# CONFIG_BINFMT_AOUT is not set
# CONFIG_BINFMT_MISC is not set
#
# Networking
#
CONFIG_NET=y
#
# Networking options
#
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
CONFIG_XFRM=y
# CONFIG_XFRM_USER is not set
# CONFIG_XFRM_SUB_POLICY is not set
# CONFIG_XFRM_MIGRATE is not set
# CONFIG_NET_KEY is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_FIB_HASH=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
# CONFIG_IP_PNP_BOOTP is not set
# CONFIG_IP_PNP_RARP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_ARPD is not set
# CONFIG_SYN_COOKIES is not set
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
# CONFIG_INET_XFRM_TUNNEL is not set
# CONFIG_INET_TUNNEL is not set
CONFIG_INET_XFRM_MODE_TRANSPORT=y
CONFIG_INET_XFRM_MODE_TUNNEL=y
CONFIG_INET_XFRM_MODE_BEET=y
# CONFIG_INET_LRO is not set
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
CONFIG_IPV6=m
# CONFIG_IPV6_PRIVACY is not set
# CONFIG_IPV6_ROUTER_PREF is not set
# CONFIG_IPV6_OPTIMISTIC_DAD is not set
# CONFIG_INET6_AH is not set
# CONFIG_INET6_ESP is not set
# CONFIG_INET6_IPCOMP is not set
# CONFIG_IPV6_MIP6 is not set
# CONFIG_INET6_XFRM_TUNNEL is not set
# CONFIG_INET6_TUNNEL is not set
# CONFIG_INET6_XFRM_MODE_TRANSPORT is not set
# CONFIG_INET6_XFRM_MODE_TUNNEL is not set
# CONFIG_INET6_XFRM_MODE_BEET is not set
# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set
# CONFIG_IPV6_SIT is not set
# CONFIG_IPV6_TUNNEL is not set
# CONFIG_IPV6_MULTIPLE_TABLES is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NET_SCHED is not set
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_NET_TCPPROBE is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_AF_RXRPC is not set
#
# Wireless
#
# CONFIG_CFG80211 is not set
# CONFIG_WIRELESS_EXT is not set
# CONFIG_MAC80211 is not set
# CONFIG_IEEE80211 is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
#
# Device Drivers
#
#
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
CONFIG_CONNECTOR=y
CONFIG_PROC_EVENTS=y
# CONFIG_MTD is not set
# CONFIG_PARPORT is not set
CONFIG_PNP=y
# CONFIG_PNP_DEBUG is not set
#
# Protocols
#
CONFIG_PNPACPI=y
CONFIG_BLK_DEV=y
CONFIG_BLK_DEV_FD=y
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_SX8 is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=4096
CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
CONFIG_MISC_DEVICES=y
# CONFIG_IBM_ASM is not set
# CONFIG_PHANTOM is not set
# CONFIG_EEPROM_93CX6 is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
# CONFIG_SONY_LAPTOP is not set
# CONFIG_THINKPAD_ACPI is not set
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_IDE_SATA is not set
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
# CONFIG_BLK_DEV_IDESCSI is not set
# CONFIG_BLK_DEV_IDEACPI is not set
# CONFIG_IDE_TASK_IOCTL is not set
# CONFIG_IDE_PROC_FS is not set
#
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=y
# CONFIG_BLK_DEV_PLATFORM is not set
# CONFIG_BLK_DEV_CMD640 is not set
# CONFIG_BLK_DEV_IDEPNP is not set
#
# PCI IDE chipsets support
#
CONFIG_BLK_DEV_IDEPCI=y
# CONFIG_IDEPCI_SHARE_IRQ is not set
CONFIG_IDEPCI_PCIBUS_ORDER=y
# CONFIG_BLK_DEV_GENERIC is not set
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_RZ1000 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
CONFIG_BLK_DEV_AMD74XX=y
# CONFIG_BLK_DEV_ATIIXP is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_CS5535 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_JMICRON is not set
# CONFIG_BLK_DEV_SC1200 is not set
CONFIG_BLK_DEV_PIIX=y
# CONFIG_BLK_DEV_IT8213 is not set
# CONFIG_BLK_DEV_IT821X is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_BLK_DEV_TC86C001 is not set
# CONFIG_IDE_ARM is not set
CONFIG_BLK_DEV_IDEDMA=y
CONFIG_IDE_ARCH_OBSOLETE_INIT=y
# CONFIG_BLK_DEV_HD is not set
#
# SCSI device support
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
CONFIG_SCSI_DMA=y
# CONFIG_SCSI_TGT is not set
CONFIG_SCSI_NETLINK=y
# CONFIG_SCSI_PROC_FS is not set
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
CONFIG_CHR_DEV_ST=y
CONFIG_CHR_DEV_OSST=y
CONFIG_BLK_DEV_SR=y
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_CHR_DEV_SG=y
# CONFIG_CHR_DEV_SCH is not set
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
# CONFIG_SCSI_MULTI_LUN is not set
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
# CONFIG_SCSI_SCAN_ASYNC is not set
CONFIG_SCSI_WAIT_SCAN=m
#
# SCSI Transports
#
CONFIG_SCSI_SPI_ATTRS=y
CONFIG_SCSI_FC_ATTRS=y
# CONFIG_SCSI_ISCSI_ATTRS is not set
CONFIG_SCSI_SAS_ATTRS=y
# CONFIG_SCSI_SAS_LIBSAS is not set
# CONFIG_SCSI_SRP_ATTRS is not set
CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AACRAID is not set
CONFIG_SCSI_AIC7XXX=y
CONFIG_AIC7XXX_CMDS_PER_DEVICE=32
CONFIG_AIC7XXX_RESET_DELAY_MS=5000
CONFIG_AIC7XXX_DEBUG_ENABLE=y
CONFIG_AIC7XXX_DEBUG_MASK=0
CONFIG_AIC7XXX_REG_PRETTY_PRINT=y
CONFIG_SCSI_AIC7XXX_OLD=y
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_AIC94XX is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_ARCMSR is not set
CONFIG_MEGARAID_NEWGEN=y
CONFIG_MEGARAID_MM=y
CONFIG_MEGARAID_MAILBOX=y
CONFIG_MEGARAID_LEGACY=y
CONFIG_MEGARAID_SAS=y
# CONFIG_SCSI_HPTIOP is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_STEX is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_QLA_FC is not set
# CONFIG_SCSI_QLA_ISCSI is not set
# CONFIG_SCSI_LPFC is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_SRP is not set
# CONFIG_ATA is not set
CONFIG_MD=y
# CONFIG_BLK_DEV_MD is not set
CONFIG_BLK_DEV_DM=y
# CONFIG_DM_DEBUG is not set
# CONFIG_DM_CRYPT is not set
# CONFIG_DM_SNAPSHOT is not set
# CONFIG_DM_MIRROR is not set
# CONFIG_DM_ZERO is not set
# CONFIG_DM_MULTIPATH is not set
# CONFIG_DM_DELAY is not set
# CONFIG_DM_UEVENT is not set
CONFIG_FUSION=y
CONFIG_FUSION_SPI=y
CONFIG_FUSION_FC=y
CONFIG_FUSION_SAS=y
CONFIG_FUSION_MAX_SGE=128
CONFIG_FUSION_CTL=y
# CONFIG_FUSION_LOGGING is not set
#
# IEEE 1394 (FireWire) support
#
# CONFIG_FIREWIRE is not set
CONFIG_IEEE1394=y
#
# Subsystem Options
#
# CONFIG_IEEE1394_VERBOSEDEBUG is not set
#
# Controllers
#
#
# Texas Instruments PCILynx requires I2C
#
CONFIG_IEEE1394_OHCI1394=y
#
# Protocols
#
# CONFIG_IEEE1394_VIDEO1394 is not set
# CONFIG_IEEE1394_SBP2 is not set
# CONFIG_IEEE1394_ETH1394_ROM_ENTRY is not set
# CONFIG_IEEE1394_ETH1394 is not set
# CONFIG_IEEE1394_DV1394 is not set
CONFIG_IEEE1394_RAWIO=y
# CONFIG_I2O is not set
CONFIG_MACINTOSH_DRIVERS=y
# CONFIG_MAC_EMUMOUSEBTN is not set
CONFIG_NETDEVICES=y
# CONFIG_NETDEVICES_MULTIQUEUE is not set
# CONFIG_DUMMY is not set
CONFIG_BONDING=y
# CONFIG_MACVLAN is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
# CONFIG_VETH is not set
# CONFIG_NET_SB1000 is not set
# CONFIG_IP1000 is not set
# CONFIG_ARCNET is not set
# CONFIG_PHYLIB is not set
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
# CONFIG_CASSINI is not set
# CONFIG_NET_VENDOR_3COM is not set
CONFIG_NET_TULIP=y
# CONFIG_DE2104X is not set
CONFIG_TULIP=y
# CONFIG_TULIP_MWI is not set
# CONFIG_TULIP_MMIO is not set
# CONFIG_TULIP_NAPI is not set
# CONFIG_DE4X5 is not set
# CONFIG_WINBOND_840 is not set
# CONFIG_DM9102 is not set
# CONFIG_ULI526X is not set
# CONFIG_HP100 is not set
# CONFIG_IBM_NEW_EMAC_ZMII is not set
# CONFIG_IBM_NEW_EMAC_RGMII is not set
# CONFIG_IBM_NEW_EMAC_TAH is not set
# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_AMD8111_ETH is not set
# CONFIG_ADAPTEC_STARFIRE is not set
CONFIG_B44=y
CONFIG_B44_PCI_AUTOSELECT=y
CONFIG_B44_PCICORE_AUTOSELECT=y
CONFIG_B44_PCI=y
CONFIG_FORCEDETH=y
# CONFIG_FORCEDETH_NAPI is not set
# CONFIG_EEPRO100 is not set
# CONFIG_E100 is not set
# CONFIG_FEALNX is not set
# CONFIG_NATSEMI is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_8139CP is not set
# CONFIG_8139TOO is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_TLAN is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_SC92031 is not set
CONFIG_NETDEV_1000=y
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_E1000E is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
# CONFIG_SIS190 is not set
# CONFIG_SKGE is not set
# CONFIG_SKY2 is not set
# CONFIG_SK98LIN is not set
# CONFIG_VIA_VELOCITY is not set
CONFIG_TIGON3=y
CONFIG_BNX2=y
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
CONFIG_NETDEV_10000=y
# CONFIG_CHELSIO_T1 is not set
# CONFIG_CHELSIO_T3 is not set
# CONFIG_IXGBE is not set
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
# CONFIG_MYRI10GE is not set
# CONFIG_NETXEN_NIC is not set
# CONFIG_NIU is not set
# CONFIG_MLX4_CORE is not set
# CONFIG_TEHUTI is not set
# CONFIG_TR is not set
#
# Wireless LAN
#
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
CONFIG_PPP=y
CONFIG_PPP_MULTILINK=y
CONFIG_PPP_FILTER=y
# CONFIG_PPP_ASYNC is not set
# CONFIG_PPP_SYNC_TTY is not set
# CONFIG_PPP_DEFLATE is not set
# CONFIG_PPP_BSDCOMP is not set
# CONFIG_PPP_MPPE is not set
# CONFIG_PPPOE is not set
# CONFIG_PPPOL2TP is not set
# CONFIG_SLIP is not set
CONFIG_SLHC=y
# CONFIG_NET_FC is not set
# CONFIG_SHAPER is not set
CONFIG_NETCONSOLE=y
# CONFIG_NETCONSOLE_DYNAMIC is not set
CONFIG_NETPOLL=y
# CONFIG_NETPOLL_TRAP is not set
CONFIG_NET_POLL_CONTROLLER=y
# CONFIG_ISDN is not set
# CONFIG_PHONE is not set
#
# Input device support
#
CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
# CONFIG_INPUT_POLLDEV is not set
#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set
#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
CONFIG_MOUSE_PS2_ALPS=y
CONFIG_MOUSE_PS2_LOGIPS2PP=y
CONFIG_MOUSE_PS2_SYNAPTICS=y
CONFIG_MOUSE_PS2_LIFEBOOK=y
CONFIG_MOUSE_PS2_TRACKPOINT=y
# CONFIG_MOUSE_PS2_TOUCHKIT is not set
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_MOUSE_APPLETOUCH is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set
#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
# CONFIG_SERIO_SERPORT is not set
# CONFIG_SERIO_CT82C710 is not set
# CONFIG_SERIO_PCIPS2 is not set
CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set
# CONFIG_GAMEPORT is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_VT_HW_CONSOLE_BINDING is not set
CONFIG_SERIAL_NONSTANDARD=y
# CONFIG_COMPUTONE is not set
# CONFIG_ROCKETPORT is not set
# CONFIG_CYCLADES is not set
# CONFIG_DIGIEPCA is not set
# CONFIG_MOXA_INTELLIO is not set
# CONFIG_MOXA_SMARTIO is not set
# CONFIG_MOXA_SMARTIO_NEW is not set
# CONFIG_ISI is not set
# CONFIG_SYNCLINK is not set
# CONFIG_SYNCLINKMP is not set
# CONFIG_SYNCLINK_GT is not set
# CONFIG_N_HDLC is not set
# CONFIG_SPECIALIX is not set
# CONFIG_SX is not set
# CONFIG_RIO is not set
CONFIG_STALDRV=y
#
# Serial drivers
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_FIX_EARLYCON_MEM=y
CONFIG_SERIAL_8250_PCI=y
CONFIG_SERIAL_8250_PNP=y
CONFIG_SERIAL_8250_NR_UARTS=4
CONFIG_SERIAL_8250_RUNTIME_UARTS=4
CONFIG_SERIAL_8250_EXTENDED=y
# CONFIG_SERIAL_8250_MANY_PORTS is not set
CONFIG_SERIAL_8250_SHARE_IRQ=y
CONFIG_SERIAL_8250_DETECT_IRQ=y
CONFIG_SERIAL_8250_RSA=y
#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
# CONFIG_IPMI_HANDLER is not set
# CONFIG_HW_RANDOM is not set
# CONFIG_NVRAM is not set
CONFIG_RTC=y
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_SONYPI is not set
# CONFIG_MWAVE is not set
# CONFIG_PC8736x_GPIO is not set
# CONFIG_NSC_GPIO is not set
# CONFIG_CS5535_GPIO is not set
CONFIG_RAW_DRIVER=y
CONFIG_MAX_RAW_DEVS=256
CONFIG_HPET=y
# CONFIG_HPET_RTC_IRQ is not set
CONFIG_HPET_MMAP=y
CONFIG_HANGCHECK_TIMER=y
# CONFIG_TCG_TPM is not set
# CONFIG_TELCLOCK is not set
CONFIG_DEVPORT=y
# CONFIG_I2C is not set
#
# SPI support
#
# CONFIG_SPI is not set
# CONFIG_SPI_MASTER is not set
# CONFIG_W1 is not set
CONFIG_POWER_SUPPLY=y
# CONFIG_POWER_SUPPLY_DEBUG is not set
# CONFIG_PDA_POWER is not set
# CONFIG_BATTERY_DS2760 is not set
# CONFIG_HWMON is not set
# CONFIG_WATCHDOG is not set
#
# Sonics Silicon Backplane
#
CONFIG_SSB_POSSIBLE=y
CONFIG_SSB=y
CONFIG_SSB_PCIHOST_POSSIBLE=y
CONFIG_SSB_PCIHOST=y
# CONFIG_SSB_DEBUG is not set
CONFIG_SSB_DRIVER_PCICORE_POSSIBLE=y
CONFIG_SSB_DRIVER_PCICORE=y
#
# Multifunction device drivers
#
# CONFIG_MFD_SM501 is not set
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
# CONFIG_DVB_CORE is not set
CONFIG_DAB=y
#
# Graphics support
#
CONFIG_AGP=y
CONFIG_AGP_ALI=y
CONFIG_AGP_ATI=y
# CONFIG_AGP_AMD is not set
CONFIG_AGP_AMD64=y
CONFIG_AGP_INTEL=y
# CONFIG_AGP_NVIDIA is not set
# CONFIG_AGP_SIS is not set
# CONFIG_AGP_SWORKS is not set
# CONFIG_AGP_VIA is not set
# CONFIG_AGP_EFFICEON is not set
CONFIG_DRM=y
# CONFIG_DRM_TDFX is not set
# CONFIG_DRM_R128 is not set
CONFIG_DRM_RADEON=y
# CONFIG_DRM_I810 is not set
# CONFIG_DRM_I830 is not set
# CONFIG_DRM_I915 is not set
# CONFIG_DRM_MGA is not set
# CONFIG_DRM_SIS is not set
# CONFIG_DRM_VIA is not set
# CONFIG_DRM_SAVAGE is not set
# CONFIG_VGASTATE is not set
CONFIG_VIDEO_OUTPUT_CONTROL=m
# CONFIG_FB is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Display device support
#
# CONFIG_DISPLAY_SUPPORT is not set
#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
CONFIG_VGACON_SOFT_SCROLLBACK=y
CONFIG_VGACON_SOFT_SCROLLBACK_SIZE=128
CONFIG_VIDEO_SELECT=y
CONFIG_DUMMY_CONSOLE=y
#
# Sound
#
CONFIG_SOUND=y
#
# Advanced Linux Sound Architecture
#
# CONFIG_SND is not set
#
# Open Sound System
#
CONFIG_SOUND_PRIME=y
# CONFIG_SOUND_TRIDENT is not set
# CONFIG_SOUND_MSNDCLAS is not set
# CONFIG_SOUND_MSNDPIN is not set
# CONFIG_SOUND_OSS is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
# CONFIG_USB is not set
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
# CONFIG_MMC is not set
# CONFIG_NEW_LEDS is not set
# CONFIG_INFINIBAND is not set
# CONFIG_EDAC is not set
# CONFIG_RTC_CLASS is not set
# CONFIG_DMADEVICES is not set
CONFIG_VIRTUALIZATION=y
# CONFIG_KVM is not set
#
# Userspace I/O
#
# CONFIG_UIO is not set
#
# Firmware Drivers
#
# CONFIG_EDD is not set
# CONFIG_DELL_RBU is not set
# CONFIG_DCDBAS is not set
CONFIG_DMIID=y
#
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
CONFIG_EXT2_FS_SECURITY=y
CONFIG_EXT2_FS_XIP=y
CONFIG_FS_XIP=y
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_EXT3_FS_SECURITY=y
# CONFIG_EXT4DEV_FS is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
CONFIG_REISERFS_FS=y
CONFIG_REISERFS_CHECK=y
CONFIG_REISERFS_PROC_INFO=y
CONFIG_REISERFS_FS_XATTR=y
CONFIG_REISERFS_FS_POSIX_ACL=y
CONFIG_REISERFS_FS_SECURITY=y
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_QUOTA is not set
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
CONFIG_AUTOFS4_FS=y
# CONFIG_FUSE_FS is not set
#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
# CONFIG_JOLIET is not set
# CONFIG_ZISOFS is not set
# CONFIG_UDF_FS is not set
#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
# CONFIG_NTFS_FS is not set
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
# CONFIG_PROC_KCORE is not set
CONFIG_PROC_SYSCTL=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_TMPFS_POSIX_ACL is not set
CONFIG_HUGETLBFS=y
CONFIG_HUGETLB_PAGE=y
CONFIG_CONFIGFS_FS=y
#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
# CONFIG_NFS_FS is not set
# CONFIG_NFSD is not set
CONFIG_SMB_FS=y
# CONFIG_SMB_NLS_DEFAULT is not set
CONFIG_CIFS=y
# CONFIG_CIFS_STATS is not set
# CONFIG_CIFS_WEAK_PW_HASH is not set
# CONFIG_CIFS_XATTR is not set
# CONFIG_CIFS_DEBUG2 is not set
# CONFIG_CIFS_EXPERIMENTAL is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
# CONFIG_NLS_CODEPAGE_850 is not set
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
CONFIG_NLS_ASCII=y
CONFIG_NLS_ISO8859_1=y
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
CONFIG_NLS_ISO8859_15=y
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
CONFIG_NLS_UTF8=y
# CONFIG_DLM is not set
CONFIG_INSTRUMENTATION=y
CONFIG_PROFILING=y
CONFIG_OPROFILE=y
CONFIG_KPROBES=y
# CONFIG_MARKERS is not set
#
# Kernel hacking
#
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
# CONFIG_PRINTK_TIME is not set
CONFIG_ENABLE_WARN_DEPRECATED=y
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_MAGIC_SYSRQ=y
CONFIG_UNUSED_SYMBOLS=y
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHED_DEBUG is not set
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
CONFIG_DEBUG_SLAB=y
CONFIG_DEBUG_SLAB_LEAK=y
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
CONFIG_DEBUG_SPINLOCK=y
CONFIG_DEBUG_MUTEXES=y
CONFIG_DEBUG_LOCK_ALLOC=y
CONFIG_PROVE_LOCKING=y
CONFIG_LOCKDEP=y
# CONFIG_LOCK_STAT is not set
CONFIG_DEBUG_LOCKDEP=y
CONFIG_TRACE_IRQFLAGS=y
CONFIG_DEBUG_SPINLOCK_SLEEP=y
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
CONFIG_STACKTRACE=y
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_HIGHMEM is not set
CONFIG_DEBUG_BUGVERBOSE=y
CONFIG_DEBUG_INFO=y
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
CONFIG_FRAME_POINTER=y
CONFIG_FORCED_INLINING=y
# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_LKDTM is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_PROVIDE_OHCI1394_DMA_INIT is not set
# CONFIG_SAMPLES is not set
# CONFIG_WANT_EXTRA_DEBUG_INFORMATION is not set
# CONFIG_UNWIND_INFO is not set
# CONFIG_KGDB is not set
# CONFIG_KGDB_ATTACH_WAIT is not set
CONFIG_EARLY_PRINTK=y
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_DEBUG_RODATA is not set
# CONFIG_4KSTACKS is not set
CONFIG_X86_FIND_SMP_CONFIG=y
CONFIG_X86_MPPARSE=y
CONFIG_DOUBLEFAULT=y
CONFIG_IO_DELAY_TYPE_0X80=0
CONFIG_IO_DELAY_TYPE_0XED=1
CONFIG_IO_DELAY_TYPE_UDELAY=2
CONFIG_IO_DELAY_TYPE_NONE=3
# CONFIG_IO_DELAY_0X80 is not set
# CONFIG_IO_DELAY_0XED is not set
CONFIG_IO_DELAY_UDELAY=y
# CONFIG_IO_DELAY_NONE is not set
CONFIG_DEFAULT_IO_DELAY_TYPE=2
#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
# CONFIG_SECURITY_FILE_CAPABILITIES is not set
# CONFIG_CRYPTO is not set
#
# Library routines
#
CONFIG_BITREVERSE=y
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
# CONFIG_CRC_ITU_T is not set
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
# CONFIG_LIBCRC32C is not set
CONFIG_AUDIT_GENERIC=y
CONFIG_ZLIB_INFLATE=y
CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
(Anything else you need, please let me know!)
--
regards,
Dhaval
Dhaval Giani wrote:
>>
>> Could you give more details of your setup? I'm trying to figure out
>> exactly what it is in kexec that goes goofy, but there seems to be an
>> enormous number of codepaths, all different, depending on things like which
>> kind of kernel. The more closely I can replicate your failure, the quicker
>> I should be able to locate the problem.
>>
>
>
> (Anything else you need, please let me know!)
- Is your pre- and post-kexec kernels the same kernel?
- What format are you using for the post-kexec kernel?
- Exact kexec command line?
- Exact boot configuration for the pre-kexec kernel?
If you can send me the images that would be extra helpful.
Thanks!
-hpa
Dhaval Giani wrote:
>
> .config
>
This appears to be unrelated, but booting this configuration on a stock
2.6.24-rc7 kernel crashes during bootup with no initrd if the memory
size is 896 MB or less (i.e. lowmem only):
Bad page state in process 'swapper'
page:c1b59800 flags:0xdead4aad mapping:00000000 mapcount:0 count:0
Trying to fix it up, but a reboot is needed
Backtrace:
Pid: 0, comm: swapper Not tainted 2.6.24-rc7 #1
[<c0105ff3>] show_trace_log_lvl+0x1a/0x2f
[<c0106885>] show_trace+0x12/0x14
[<c0106b7b>] dump_stack+0x6c/0x72
[<c015c5c3>] bad_page+0x67/0x93
[<c015d33e>] __free_pages_ok+0x63/0x2f3
[<c015d5f2>] __free_pages+0x24/0x26
[<c05c70ea>] __free_pages_bootmem+0x5f/0x63
[<c05c57c9>] free_all_bootmem_core+0xcd/0x1a4
[<c05c58ad>] free_all_bootmem+0xd/0xf
[<c05c244c>] mem_init+0x81/0x31b
[<c05b4639>] start_kernel+0x2af/0x335
[<00000000>] 0x0
=======================
Bad page state in process 'swapper'
[...]
=======================
BUG: spinlock lockup on CPU#0, swapper/0, 00000e28
Pid: 0, comm: swapper Tainted: G B 2.6.24-rc7 #1
[<c0105ff3>] show_trace_log_lvl+0x1a/0x2f
[<c0106885>] show_trace+0x12/0x14
[<c0106b7b>] dump_stack+0x6c/0x72
[<c024b9a9>] _raw_spin_lock+0xc1/0xe2
[<c0411d08>] _spin_lock+0x32/0x38
[<c015d3f9>] __free_pages_ok+0x11e/0x2f3
[<c015d5f2>] __free_pages+0x24/0x26
[<c05c70ea>] __free_pages_bootmem+0x5f/0x63
[<c05c57c9>] free_all_bootmem_core+0xcd/0x1a4
[<c05c58ad>] free_all_bootmem+0xd/0xf
[<c05c244c>] mem_init+0x81/0x31b
[<c05b4639>] start_kernel+0x2af/0x335
[<00000000>] 0x0
=======================
[hang]
Booting with > 896 MB works...
-hpa