Hi,
Running latest -git (head 91525300baf162e83e923b09ca286f9205e21522) and
connecting my cf usb storage device yields and endless stream of:
Initializing USB Mass Storage driver...
scsi6 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
scsi 6:0:0:0: Direct-Access Generic STORAGE DEVICE 0125 PQ: 0
ANSI: 0
sd 6:0:0:0: [sdb] 4001760 512-byte hardware sectors (2049 MB)
sd 6:0:0:0: [sdb] Write Protect is off
sd 6:0:0:0: [sdb] Mode Sense: 02 00 00 00
sd 6:0:0:0: [sdb] Assuming drive cache: write through
sd 6:0:0:0: [sdb] 4001760 512-byte hardware sectors (2049 MB)
sd 6:0:0:0: [sdb] Write Protect is off
sd 6:0:0:0: [sdb] Mode Sense: 02 00 00 00
sd 6:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 6:0:0:0: [sdb] Attached SCSI removable disk
sd 6:0:0:0: Attached scsi generic sg1 type 0
scsi 6:0:0:1: Direct-Access Generic STORAGE DEVICE 0125 PQ: 0
ANSI: 0
usb 5-1: reset high speed USB device using ehci_hcd and address 2
usb 5-1: reset high speed USB device using ehci_hcd and address 2
usb 5-1: reset high speed USB device using ehci_hcd and address 2
usb 5-1: reset high speed USB device using ehci_hcd and address 2
usb 5-1: reset high speed USB device using ehci_hcd and address 2
usb 5-1: reset high speed USB device using ehci_hcd and address 2
usb 5-1: reset high speed USB device using ehci_hcd and address 2
[...]
until I disconnect it. The device doesn't work. Worked fine in 2.6.24.
I'm attaching boot messages and my .config.
--
Jens Axboe
On Mon, Jan 28, 2008 at 09:49:35PM +0100, Jens Axboe wrote:
> Hi,
>
> Running latest -git (head 91525300baf162e83e923b09ca286f9205e21522) and
> connecting my cf usb storage device yields and endless stream of:
>
> Initializing USB Mass Storage driver...
> scsi6 : SCSI emulation for USB Mass Storage devices
> usb-storage: device found at 2
> usb-storage: waiting for device to settle before scanning
> usbcore: registered new interface driver usb-storage
> USB Mass Storage support registered.
> scsi 6:0:0:0: Direct-Access Generic STORAGE DEVICE 0125 PQ: 0
> ANSI: 0
> sd 6:0:0:0: [sdb] 4001760 512-byte hardware sectors (2049 MB)
> sd 6:0:0:0: [sdb] Write Protect is off
> sd 6:0:0:0: [sdb] Mode Sense: 02 00 00 00
> sd 6:0:0:0: [sdb] Assuming drive cache: write through
> sd 6:0:0:0: [sdb] 4001760 512-byte hardware sectors (2049 MB)
> sd 6:0:0:0: [sdb] Write Protect is off
> sd 6:0:0:0: [sdb] Mode Sense: 02 00 00 00
> sd 6:0:0:0: [sdb] Assuming drive cache: write through
> sdb: sdb1
> sd 6:0:0:0: [sdb] Attached SCSI removable disk
> sd 6:0:0:0: Attached scsi generic sg1 type 0
> scsi 6:0:0:1: Direct-Access Generic STORAGE DEVICE 0125 PQ: 0
> ANSI: 0
> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> [...]
>
> until I disconnect it. The device doesn't work. Worked fine in 2.6.24.
> I'm attaching boot messages and my .config.
That's a bit wierd, as we haven't added any USB patches to the -git tree
yet after 2.6.24 :)
Could this be caused by some scsi changes perhaps?
thanks,
greg k-h
On Mon, Jan 28 2008, Greg KH wrote:
> On Mon, Jan 28, 2008 at 09:49:35PM +0100, Jens Axboe wrote:
> > Hi,
> >
> > Running latest -git (head 91525300baf162e83e923b09ca286f9205e21522) and
> > connecting my cf usb storage device yields and endless stream of:
> >
> > Initializing USB Mass Storage driver...
> > scsi6 : SCSI emulation for USB Mass Storage devices
> > usb-storage: device found at 2
> > usb-storage: waiting for device to settle before scanning
> > usbcore: registered new interface driver usb-storage
> > USB Mass Storage support registered.
> > scsi 6:0:0:0: Direct-Access Generic STORAGE DEVICE 0125 PQ: 0
> > ANSI: 0
> > sd 6:0:0:0: [sdb] 4001760 512-byte hardware sectors (2049 MB)
> > sd 6:0:0:0: [sdb] Write Protect is off
> > sd 6:0:0:0: [sdb] Mode Sense: 02 00 00 00
> > sd 6:0:0:0: [sdb] Assuming drive cache: write through
> > sd 6:0:0:0: [sdb] 4001760 512-byte hardware sectors (2049 MB)
> > sd 6:0:0:0: [sdb] Write Protect is off
> > sd 6:0:0:0: [sdb] Mode Sense: 02 00 00 00
> > sd 6:0:0:0: [sdb] Assuming drive cache: write through
> > sdb: sdb1
> > sd 6:0:0:0: [sdb] Attached SCSI removable disk
> > sd 6:0:0:0: Attached scsi generic sg1 type 0
> > scsi 6:0:0:1: Direct-Access Generic STORAGE DEVICE 0125 PQ: 0
> > ANSI: 0
> > usb 5-1: reset high speed USB device using ehci_hcd and address 2
> > usb 5-1: reset high speed USB device using ehci_hcd and address 2
> > usb 5-1: reset high speed USB device using ehci_hcd and address 2
> > usb 5-1: reset high speed USB device using ehci_hcd and address 2
> > usb 5-1: reset high speed USB device using ehci_hcd and address 2
> > usb 5-1: reset high speed USB device using ehci_hcd and address 2
> > usb 5-1: reset high speed USB device using ehci_hcd and address 2
> > [...]
> >
> > until I disconnect it. The device doesn't work. Worked fine in 2.6.24.
> > I'm attaching boot messages and my .config.
>
> That's a bit wierd, as we haven't added any USB patches to the -git tree
> yet after 2.6.24 :)
>
> Could this be caused by some scsi changes perhaps?
Heh, I guess it could! I'll double check, I reproduced it with two
distinct boots before posting.
--
Jens Axboe
Greg KH wrote:
> On Mon, Jan 28, 2008 at 09:49:35PM +0100, Jens Axboe wrote:
>> Hi,
>>
>> Running latest -git (head 91525300baf162e83e923b09ca286f9205e21522) and
>> connecting my cf usb storage device yields and endless stream of:
>>
>> Initializing USB Mass Storage driver...
>> scsi6 : SCSI emulation for USB Mass Storage devices
>> usb-storage: device found at 2
>> usb-storage: waiting for device to settle before scanning
>> usbcore: registered new interface driver usb-storage
>> USB Mass Storage support registered.
>> scsi 6:0:0:0: Direct-Access Generic STORAGE DEVICE 0125 PQ: 0
>> ANSI: 0
>> sd 6:0:0:0: [sdb] 4001760 512-byte hardware sectors (2049 MB)
>> sd 6:0:0:0: [sdb] Write Protect is off
>> sd 6:0:0:0: [sdb] Mode Sense: 02 00 00 00
>> sd 6:0:0:0: [sdb] Assuming drive cache: write through
>> sd 6:0:0:0: [sdb] 4001760 512-byte hardware sectors (2049 MB)
>> sd 6:0:0:0: [sdb] Write Protect is off
>> sd 6:0:0:0: [sdb] Mode Sense: 02 00 00 00
>> sd 6:0:0:0: [sdb] Assuming drive cache: write through
>> sdb: sdb1
>> sd 6:0:0:0: [sdb] Attached SCSI removable disk
>> sd 6:0:0:0: Attached scsi generic sg1 type 0
>> scsi 6:0:0:1: Direct-Access Generic STORAGE DEVICE 0125 PQ: 0
>> ANSI: 0
>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
>> [...]
>>
>> until I disconnect it. The device doesn't work. Worked fine in 2.6.24.
>> I'm attaching boot messages and my .config.
>
> That's a bit wierd, as we haven't added any USB patches to the -git tree
> yet after 2.6.24 :)
>
> Could this be caused by some scsi changes perhaps?
>
> thanks,
>
> greg k-h
> -
Yes it is ;)
Jens could you test the patch below? if it works I'll submit a proper
patch. Please forgive me for the bug.
Matthew, Greg, Is there a way to extract from messages the usb storage transport
used? I'm guessing it is freecom do to the fact that I find a bug there.
Thanks
Boaz
---
drivers/usb/storage/freecom.c | 4 ++--
drivers/usb/storage/transport.c | 12 +++++++++---
drivers/usb/storage/transport.h | 3 ++-
3 files changed, 13 insertions(+), 6 deletions(-)
diff --git a/drivers/usb/storage/freecom.c b/drivers/usb/storage/freecom.c
index f5a4e8d..8d77603 100644
--- a/drivers/usb/storage/freecom.c
+++ b/drivers/usb/storage/freecom.c
@@ -132,7 +132,7 @@ freecom_readdata (struct scsi_cmnd *srb, struct us_data *us,
/* Now transfer all of our blocks. */
US_DEBUGP("Start of read\n");
- result = usb_stor_bulk_srb(us, ipipe, srb);
+ result = usb_stor_bulk_srb_length(us, ipipe, srb, count);
US_DEBUGP("freecom_readdata done!\n");
if (result > USB_STOR_XFER_SHORT)
@@ -165,7 +165,7 @@ freecom_writedata (struct scsi_cmnd *srb, struct us_data *us,
/* Now transfer all of our blocks. */
US_DEBUGP("Start of write\n");
- result = usb_stor_bulk_srb(us, opipe, srb);
+ result = usb_stor_bulk_srb_length(us, opipe, srb, count);
US_DEBUGP("freecom_writedata done!\n");
if (result > USB_STOR_XFER_SHORT)
diff --git a/drivers/usb/storage/transport.c b/drivers/usb/storage/transport.c
index d9f4912..5072235 100644
--- a/drivers/usb/storage/transport.c
+++ b/drivers/usb/storage/transport.c
@@ -462,18 +462,24 @@ static int usb_stor_bulk_transfer_sglist(struct us_data *us, unsigned int pipe,
* Common used function. Transfer a complete command
* via usb_stor_bulk_transfer_sglist() above. Set cmnd resid
*/
-int usb_stor_bulk_srb(struct us_data* us, unsigned int pipe,
- struct scsi_cmnd* srb)
+int usb_stor_bulk_srb_length(struct us_data* us, unsigned int pipe,
+ struct scsi_cmnd* srb, unsigned length)
{
unsigned int partial;
int result = usb_stor_bulk_transfer_sglist(us, pipe, scsi_sglist(srb),
- scsi_sg_count(srb), scsi_bufflen(srb),
+ scsi_sg_count(srb), length,
&partial);
scsi_set_resid(srb, scsi_bufflen(srb) - partial);
return result;
}
+int usb_stor_bulk_srb(struct us_data* us, unsigned int pipe,
+ struct scsi_cmnd* srb)
+{
+ return usb_stor_bulk_srb_length(us, pipe, srb, scsi_bufflen(srb));
+}
+
/*
* Transfer an entire SCSI command's worth of data payload over the bulk
* pipe.
diff --git a/drivers/usb/storage/transport.h b/drivers/usb/storage/transport.h
index ada7c2f..03e395d 100644
--- a/drivers/usb/storage/transport.h
+++ b/drivers/usb/storage/transport.h
@@ -139,8 +139,9 @@ extern int usb_stor_bulk_transfer_buf(struct us_data *us, unsigned int pipe,
void *buf, unsigned int length, unsigned int *act_len);
extern int usb_stor_bulk_transfer_sg(struct us_data *us, unsigned int pipe,
void *buf, unsigned int length, int use_sg, int *residual);
+extern int usb_stor_bulk_srb_length(struct us_data* us, unsigned int pipe,
+ struct scsi_cmnd* srb, unsigned length);
extern int usb_stor_bulk_srb(struct us_data* us, unsigned int pipe,
struct scsi_cmnd* srb);
-
extern int usb_stor_port_reset(struct us_data *us);
#endif
On Tue, Jan 29 2008, Boaz Harrosh wrote:
> Greg KH wrote:
> > On Mon, Jan 28, 2008 at 09:49:35PM +0100, Jens Axboe wrote:
> >> Hi,
> >>
> >> Running latest -git (head 91525300baf162e83e923b09ca286f9205e21522) and
> >> connecting my cf usb storage device yields and endless stream of:
> >>
> >> Initializing USB Mass Storage driver...
> >> scsi6 : SCSI emulation for USB Mass Storage devices
> >> usb-storage: device found at 2
> >> usb-storage: waiting for device to settle before scanning
> >> usbcore: registered new interface driver usb-storage
> >> USB Mass Storage support registered.
> >> scsi 6:0:0:0: Direct-Access Generic STORAGE DEVICE 0125 PQ: 0
> >> ANSI: 0
> >> sd 6:0:0:0: [sdb] 4001760 512-byte hardware sectors (2049 MB)
> >> sd 6:0:0:0: [sdb] Write Protect is off
> >> sd 6:0:0:0: [sdb] Mode Sense: 02 00 00 00
> >> sd 6:0:0:0: [sdb] Assuming drive cache: write through
> >> sd 6:0:0:0: [sdb] 4001760 512-byte hardware sectors (2049 MB)
> >> sd 6:0:0:0: [sdb] Write Protect is off
> >> sd 6:0:0:0: [sdb] Mode Sense: 02 00 00 00
> >> sd 6:0:0:0: [sdb] Assuming drive cache: write through
> >> sdb: sdb1
> >> sd 6:0:0:0: [sdb] Attached SCSI removable disk
> >> sd 6:0:0:0: Attached scsi generic sg1 type 0
> >> scsi 6:0:0:1: Direct-Access Generic STORAGE DEVICE 0125 PQ: 0
> >> ANSI: 0
> >> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> >> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> >> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> >> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> >> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> >> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> >> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> >> [...]
> >>
> >> until I disconnect it. The device doesn't work. Worked fine in 2.6.24.
> >> I'm attaching boot messages and my .config.
> >
> > That's a bit wierd, as we haven't added any USB patches to the -git tree
> > yet after 2.6.24 :)
> >
> > Could this be caused by some scsi changes perhaps?
> >
> > thanks,
> >
> > greg k-h
> > -
> Yes it is ;)
>
> Jens could you test the patch below? if it works I'll submit a proper
> patch. Please forgive me for the bug.
No difference, still just a lot of resets.
--
Jens Axboe
On Tue, Jan 29 2008 at 15:54 +0200, Jens Axboe <[email protected]> wrote:
> On Tue, Jan 29 2008, Boaz Harrosh wrote:
>> Greg KH wrote:
>>> On Mon, Jan 28, 2008 at 09:49:35PM +0100, Jens Axboe wrote:
>>>> Hi,
>>>>
>>>> Running latest -git (head 91525300baf162e83e923b09ca286f9205e21522) and
>>>> connecting my cf usb storage device yields and endless stream of:
>>>>
>>>> Initializing USB Mass Storage driver...
>>>> scsi6 : SCSI emulation for USB Mass Storage devices
>>>> usb-storage: device found at 2
>>>> usb-storage: waiting for device to settle before scanning
>>>> usbcore: registered new interface driver usb-storage
>>>> USB Mass Storage support registered.
>>>> scsi 6:0:0:0: Direct-Access Generic STORAGE DEVICE 0125 PQ: 0
>>>> ANSI: 0
>>>> sd 6:0:0:0: [sdb] 4001760 512-byte hardware sectors (2049 MB)
>>>> sd 6:0:0:0: [sdb] Write Protect is off
>>>> sd 6:0:0:0: [sdb] Mode Sense: 02 00 00 00
>>>> sd 6:0:0:0: [sdb] Assuming drive cache: write through
>>>> sd 6:0:0:0: [sdb] 4001760 512-byte hardware sectors (2049 MB)
>>>> sd 6:0:0:0: [sdb] Write Protect is off
>>>> sd 6:0:0:0: [sdb] Mode Sense: 02 00 00 00
>>>> sd 6:0:0:0: [sdb] Assuming drive cache: write through
>>>> sdb: sdb1
>>>> sd 6:0:0:0: [sdb] Attached SCSI removable disk
>>>> sd 6:0:0:0: Attached scsi generic sg1 type 0
>>>> scsi 6:0:0:1: Direct-Access Generic STORAGE DEVICE 0125 PQ: 0
>>>> ANSI: 0
>>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
>>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
>>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
>>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
>>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
>>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
>>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
>>>> [...]
>>>>
>>>> until I disconnect it. The device doesn't work. Worked fine in 2.6.24.
>>>> I'm attaching boot messages and my .config.
>>> That's a bit wierd, as we haven't added any USB patches to the -git tree
>>> yet after 2.6.24 :)
>>>
>>> Could this be caused by some scsi changes perhaps?
>>>
>>> thanks,
>>>
>>> greg k-h
>>> -
>> Yes it is ;)
>>
>> Jens could you test the patch below? if it works I'll submit a proper
>> patch. Please forgive me for the bug.
>
> No difference, still just a lot of resets.
>
Where you able to figure out which usb storage transport is used?
in drivers/usb/storage/usb.c you have get_protocol() and get_transport()
functions. I'm not sure if these get stored in sysfs perhaps. This will
pinpoint better where to look. Let me research a bit.
Thanks for testing
Boaz
On Tue, Jan 29 2008, Boaz Harrosh wrote:
> On Tue, Jan 29 2008 at 15:54 +0200, Jens Axboe <[email protected]> wrote:
> > On Tue, Jan 29 2008, Boaz Harrosh wrote:
> >> Greg KH wrote:
> >>> On Mon, Jan 28, 2008 at 09:49:35PM +0100, Jens Axboe wrote:
> >>>> Hi,
> >>>>
> >>>> Running latest -git (head 91525300baf162e83e923b09ca286f9205e21522) and
> >>>> connecting my cf usb storage device yields and endless stream of:
> >>>>
> >>>> Initializing USB Mass Storage driver...
> >>>> scsi6 : SCSI emulation for USB Mass Storage devices
> >>>> usb-storage: device found at 2
> >>>> usb-storage: waiting for device to settle before scanning
> >>>> usbcore: registered new interface driver usb-storage
> >>>> USB Mass Storage support registered.
> >>>> scsi 6:0:0:0: Direct-Access Generic STORAGE DEVICE 0125 PQ: 0
> >>>> ANSI: 0
> >>>> sd 6:0:0:0: [sdb] 4001760 512-byte hardware sectors (2049 MB)
> >>>> sd 6:0:0:0: [sdb] Write Protect is off
> >>>> sd 6:0:0:0: [sdb] Mode Sense: 02 00 00 00
> >>>> sd 6:0:0:0: [sdb] Assuming drive cache: write through
> >>>> sd 6:0:0:0: [sdb] 4001760 512-byte hardware sectors (2049 MB)
> >>>> sd 6:0:0:0: [sdb] Write Protect is off
> >>>> sd 6:0:0:0: [sdb] Mode Sense: 02 00 00 00
> >>>> sd 6:0:0:0: [sdb] Assuming drive cache: write through
> >>>> sdb: sdb1
> >>>> sd 6:0:0:0: [sdb] Attached SCSI removable disk
> >>>> sd 6:0:0:0: Attached scsi generic sg1 type 0
> >>>> scsi 6:0:0:1: Direct-Access Generic STORAGE DEVICE 0125 PQ: 0
> >>>> ANSI: 0
> >>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> >>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> >>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> >>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> >>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> >>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> >>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> >>>> [...]
> >>>>
> >>>> until I disconnect it. The device doesn't work. Worked fine in 2.6.24.
> >>>> I'm attaching boot messages and my .config.
> >>> That's a bit wierd, as we haven't added any USB patches to the -git tree
> >>> yet after 2.6.24 :)
> >>>
> >>> Could this be caused by some scsi changes perhaps?
> >>>
> >>> thanks,
> >>>
> >>> greg k-h
> >>> -
> >> Yes it is ;)
> >>
> >> Jens could you test the patch below? if it works I'll submit a proper
> >> patch. Please forgive me for the bug.
> >
> > No difference, still just a lot of resets.
> >
> Where you able to figure out which usb storage transport is used?
>
> in drivers/usb/storage/usb.c you have get_protocol() and get_transport()
> functions. I'm not sure if these get stored in sysfs perhaps. This will
> pinpoint better where to look. Let me research a bit.
Did the quick'n easy and dumped it. Protocol is 'Transparent SCSI' and
transport is 'Bulk'
--
Jens Axboe
On Tue, Jan 29 2008 at 16:06 +0200, Boaz Harrosh <[email protected]> wrote:
> On Tue, Jan 29 2008 at 15:54 +0200, Jens Axboe <[email protected]> wrote:
>> On Tue, Jan 29 2008, Boaz Harrosh wrote:
>>> Greg KH wrote:
>>>> On Mon, Jan 28, 2008 at 09:49:35PM +0100, Jens Axboe wrote:
>>>>> Hi,
>>>>>
>>>>> Running latest -git (head 91525300baf162e83e923b09ca286f9205e21522) and
>>>>> connecting my cf usb storage device yields and endless stream of:
>>>>>
>>>>> Initializing USB Mass Storage driver...
>>>>> scsi6 : SCSI emulation for USB Mass Storage devices
>>>>> usb-storage: device found at 2
>>>>> usb-storage: waiting for device to settle before scanning
>>>>> usbcore: registered new interface driver usb-storage
>>>>> USB Mass Storage support registered.
>>>>> scsi 6:0:0:0: Direct-Access Generic STORAGE DEVICE 0125 PQ: 0
>>>>> ANSI: 0
>>>>> sd 6:0:0:0: [sdb] 4001760 512-byte hardware sectors (2049 MB)
>>>>> sd 6:0:0:0: [sdb] Write Protect is off
>>>>> sd 6:0:0:0: [sdb] Mode Sense: 02 00 00 00
>>>>> sd 6:0:0:0: [sdb] Assuming drive cache: write through
>>>>> sd 6:0:0:0: [sdb] 4001760 512-byte hardware sectors (2049 MB)
>>>>> sd 6:0:0:0: [sdb] Write Protect is off
>>>>> sd 6:0:0:0: [sdb] Mode Sense: 02 00 00 00
>>>>> sd 6:0:0:0: [sdb] Assuming drive cache: write through
>>>>> sdb: sdb1
>>>>> sd 6:0:0:0: [sdb] Attached SCSI removable disk
>>>>> sd 6:0:0:0: Attached scsi generic sg1 type 0
>>>>> scsi 6:0:0:1: Direct-Access Generic STORAGE DEVICE 0125 PQ: 0
>>>>> ANSI: 0
>>>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
>>>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
>>>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
>>>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
>>>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
>>>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
>>>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
>>>>> [...]
>>>>>
>>>>> until I disconnect it. The device doesn't work. Worked fine in 2.6.24.
>>>>> I'm attaching boot messages and my .config.
>>>> That's a bit wierd, as we haven't added any USB patches to the -git tree
>>>> yet after 2.6.24 :)
>>>>
>>>> Could this be caused by some scsi changes perhaps?
>>>>
>>>> thanks,
>>>>
>>>> greg k-h
>>>> -
>>> Yes it is ;)
>>>
>>> Jens could you test the patch below? if it works I'll submit a proper
>>> patch. Please forgive me for the bug.
>> No difference, still just a lot of resets.
>>
> Where you able to figure out which usb storage transport is used?
>
> in drivers/usb/storage/usb.c you have get_protocol() and get_transport()
> functions. I'm not sure if these get stored in sysfs perhaps. This will
> pinpoint better where to look. Let me research a bit.
>
>From inspection of code it should be in /proc/scsi somewhere look for:
SPRINTF(" Protocol: %s\n", us->protocol_name);
SPRINTF(" Transport: %s\n", us->transport_name);
(it's proc_info() in drivers/usb/storage/scsiglue.c)
Thanks
Boaz
On Tue, Jan 29 2008 at 16:11 +0200, Jens Axboe <[email protected]> wrote:
> On Tue, Jan 29 2008, Boaz Harrosh wrote:
>> On Tue, Jan 29 2008 at 15:54 +0200, Jens Axboe <[email protected]> wrote:
>>> On Tue, Jan 29 2008, Boaz Harrosh wrote:
>>>> Greg KH wrote:
>>>>> On Mon, Jan 28, 2008 at 09:49:35PM +0100, Jens Axboe wrote:
>>>>>> Hi,
>>>>>>
>>>>>> Running latest -git (head 91525300baf162e83e923b09ca286f9205e21522) and
>>>>>> connecting my cf usb storage device yields and endless stream of:
>>>>>>
>>>>>> Initializing USB Mass Storage driver...
>>>>>> scsi6 : SCSI emulation for USB Mass Storage devices
>>>>>> usb-storage: device found at 2
>>>>>> usb-storage: waiting for device to settle before scanning
>>>>>> usbcore: registered new interface driver usb-storage
>>>>>> USB Mass Storage support registered.
>>>>>> scsi 6:0:0:0: Direct-Access Generic STORAGE DEVICE 0125 PQ: 0
>>>>>> ANSI: 0
>>>>>> sd 6:0:0:0: [sdb] 4001760 512-byte hardware sectors (2049 MB)
>>>>>> sd 6:0:0:0: [sdb] Write Protect is off
>>>>>> sd 6:0:0:0: [sdb] Mode Sense: 02 00 00 00
>>>>>> sd 6:0:0:0: [sdb] Assuming drive cache: write through
>>>>>> sd 6:0:0:0: [sdb] 4001760 512-byte hardware sectors (2049 MB)
>>>>>> sd 6:0:0:0: [sdb] Write Protect is off
>>>>>> sd 6:0:0:0: [sdb] Mode Sense: 02 00 00 00
>>>>>> sd 6:0:0:0: [sdb] Assuming drive cache: write through
>>>>>> sdb: sdb1
>>>>>> sd 6:0:0:0: [sdb] Attached SCSI removable disk
>>>>>> sd 6:0:0:0: Attached scsi generic sg1 type 0
>>>>>> scsi 6:0:0:1: Direct-Access Generic STORAGE DEVICE 0125 PQ: 0
>>>>>> ANSI: 0
>>>>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
>>>>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
>>>>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
>>>>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
>>>>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
>>>>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
>>>>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
>>>>>> [...]
>>>>>>
>>>>>> until I disconnect it. The device doesn't work. Worked fine in 2.6.24.
>>>>>> I'm attaching boot messages and my .config.
>>>>> That's a bit wierd, as we haven't added any USB patches to the -git tree
>>>>> yet after 2.6.24 :)
>>>>>
>>>>> Could this be caused by some scsi changes perhaps?
>>>>>
>>>>> thanks,
>>>>>
>>>>> greg k-h
>>>>> -
>>>> Yes it is ;)
>>>>
>>>> Jens could you test the patch below? if it works I'll submit a proper
>>>> patch. Please forgive me for the bug.
>>> No difference, still just a lot of resets.
>>>
>> Where you able to figure out which usb storage transport is used?
>>
>> in drivers/usb/storage/usb.c you have get_protocol() and get_transport()
>> functions. I'm not sure if these get stored in sysfs perhaps. This will
>> pinpoint better where to look. Let me research a bit.
>
> Did the quick'n easy and dumped it. Protocol is 'Transparent SCSI' and
> transport is 'Bulk'
>
Sorry for the other noise. Thanks I'll have a look.
Am Dienstag, 29. Januar 2008 15:11:08 schrieb Jens Axboe:
> On Tue, Jan 29 2008, Boaz Harrosh wrote:
> > On Tue, Jan 29 2008 at 15:54 +0200, Jens Axboe <[email protected]> wrote:
> > > On Tue, Jan 29 2008, Boaz Harrosh wrote:
> > >> Greg KH wrote:
> > > No difference, still just a lot of resets.
> > >
> > Where you able to figure out which usb storage transport is used?
> >
> > in drivers/usb/storage/usb.c you have get_protocol() and get_transport()
> > functions. I'm not sure if these get stored in sysfs perhaps. This will
> > pinpoint better where to look. Let me research a bit.
>
> Did the quick'n easy and dumped it. Protocol is 'Transparent SCSI' and
> transport is 'Bulk'
You can recompile your kernel with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG
That should tell the reason for the resets.
Regards
Oliver
On Tue, Jan 29 2008, Oliver Neukum wrote:
> Am Dienstag, 29. Januar 2008 15:11:08 schrieb Jens Axboe:
> > On Tue, Jan 29 2008, Boaz Harrosh wrote:
> > > On Tue, Jan 29 2008 at 15:54 +0200, Jens Axboe <[email protected]> wrote:
> > > > On Tue, Jan 29 2008, Boaz Harrosh wrote:
> > > >> Greg KH wrote:
>
> > > > No difference, still just a lot of resets.
> > > >
> > > Where you able to figure out which usb storage transport is used?
> > >
> > > in drivers/usb/storage/usb.c you have get_protocol() and get_transport()
> > > functions. I'm not sure if these get stored in sysfs perhaps. This will
> > > pinpoint better where to look. Let me research a bit.
> >
> > Did the quick'n easy and dumped it. Protocol is 'Transparent SCSI' and
> > transport is 'Bulk'
>
> You can recompile your kernel with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG
> That should tell the reason for the resets.
Sure, I'll do that. Will post the results tonight.
--
Jens Axboe
On Tue, 29 Jan 2008, Boaz Harrosh wrote:
> --- a/drivers/usb/storage/transport.c
> +++ b/drivers/usb/storage/transport.c
> @@ -462,18 +462,24 @@ static int usb_stor_bulk_transfer_sglist(struct us_data *us, unsigned int pipe,
> * Common used function. Transfer a complete command
> * via usb_stor_bulk_transfer_sglist() above. Set cmnd resid
> */
> -int usb_stor_bulk_srb(struct us_data* us, unsigned int pipe,
> - struct scsi_cmnd* srb)
> +int usb_stor_bulk_srb_length(struct us_data* us, unsigned int pipe,
> + struct scsi_cmnd* srb, unsigned length)
> {
> unsigned int partial;
> int result = usb_stor_bulk_transfer_sglist(us, pipe, scsi_sglist(srb),
> - scsi_sg_count(srb), scsi_bufflen(srb),
> + scsi_sg_count(srb), length,
> &partial);
>
> scsi_set_resid(srb, scsi_bufflen(srb) - partial);
> return result;
> }
>
> +int usb_stor_bulk_srb(struct us_data* us, unsigned int pipe,
> + struct scsi_cmnd* srb)
> +{
> + return usb_stor_bulk_srb_length(us, pipe, srb, scsi_bufflen(srb));
> +}
> +
I don't like this patch very much. Why add another layer of
indirection when the two subroutines do hardly any work? Leave
usb_stor_bulk_srb() the way it was, and add usb_stor_bulk_srb_length()
as a separate routine that simply calls usb_stor_bulk_transfer_sglist()
and scsi_set_resid().
BTW, the standard coding style calls for a blank line after the list of
local variables at the start of a function or block.
Alan Stern
On Tue, Jan 29, 2008 at 02:15:15PM +0200, Boaz Harrosh wrote:
> Greg KH wrote:
> > On Mon, Jan 28, 2008 at 09:49:35PM +0100, Jens Axboe wrote:
> >> Hi,
> >>
> >> Running latest -git (head 91525300baf162e83e923b09ca286f9205e21522) and
> >> connecting my cf usb storage device yields and endless stream of:
> >>
> >> Initializing USB Mass Storage driver...
> >> scsi6 : SCSI emulation for USB Mass Storage devices
> >> usb-storage: device found at 2
> >> usb-storage: waiting for device to settle before scanning
> >> usbcore: registered new interface driver usb-storage
> >> USB Mass Storage support registered.
> >> scsi 6:0:0:0: Direct-Access Generic STORAGE DEVICE 0125 PQ: 0
> >> ANSI: 0
> >> sd 6:0:0:0: [sdb] 4001760 512-byte hardware sectors (2049 MB)
> >> sd 6:0:0:0: [sdb] Write Protect is off
> >> sd 6:0:0:0: [sdb] Mode Sense: 02 00 00 00
> >> sd 6:0:0:0: [sdb] Assuming drive cache: write through
> >> sd 6:0:0:0: [sdb] 4001760 512-byte hardware sectors (2049 MB)
> >> sd 6:0:0:0: [sdb] Write Protect is off
> >> sd 6:0:0:0: [sdb] Mode Sense: 02 00 00 00
> >> sd 6:0:0:0: [sdb] Assuming drive cache: write through
> >> sdb: sdb1
> >> sd 6:0:0:0: [sdb] Attached SCSI removable disk
> >> sd 6:0:0:0: Attached scsi generic sg1 type 0
> >> scsi 6:0:0:1: Direct-Access Generic STORAGE DEVICE 0125 PQ: 0
> >> ANSI: 0
> >> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> >> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> >> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> >> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> >> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> >> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> >> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> >> [...]
> >>
> >> until I disconnect it. The device doesn't work. Worked fine in 2.6.24.
> >> I'm attaching boot messages and my .config.
> >
> > That's a bit wierd, as we haven't added any USB patches to the -git tree
> > yet after 2.6.24 :)
> >
> > Could this be caused by some scsi changes perhaps?
> >
> > thanks,
> >
> > greg k-h
> > -
> Yes it is ;)
>
> Jens could you test the patch below? if it works I'll submit a proper
> patch. Please forgive me for the bug.
>
> Matthew, Greg, Is there a way to extract from messages the usb storage transport
> used? I'm guessing it is freecom do to the fact that I find a bug there.
The freecom transport is exceptionally rare these days. It's primary user
was a device made by a company that went out of business.
Matt
--
Matthew Dharm Home: [email protected]
Maintainer, Linux USB Mass Storage Driver
Way to go, lava boy.
-- Stef to Greg
User Friendly, 3/26/1998
On Tue, Jan 29 2008 at 16:31 +0200, Oliver Neukum <[email protected]> wrote:
> Am Dienstag, 29. Januar 2008 15:11:08 schrieb Jens Axboe:
>> On Tue, Jan 29 2008, Boaz Harrosh wrote:
>>> On Tue, Jan 29 2008 at 15:54 +0200, Jens Axboe <[email protected]> wrote:
>>>> On Tue, Jan 29 2008, Boaz Harrosh wrote:
>>>>> Greg KH wrote:
>
>>>> No difference, still just a lot of resets.
>>>>
>>> Where you able to figure out which usb storage transport is used?
>>>
>>> in drivers/usb/storage/usb.c you have get_protocol() and get_transport()
>>> functions. I'm not sure if these get stored in sysfs perhaps. This will
>>> pinpoint better where to look. Let me research a bit.
>> Did the quick'n easy and dumped it. Protocol is 'Transparent SCSI' and
>> transport is 'Bulk'
>
> You can recompile your kernel with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG
> That should tell the reason for the resets.
>
> Regards
> Oliver
> -
I can not see what it is. Yes CONFIG_USB_STORAGE_DEBUG will help.
I have a device here that uses the same trasport/protocol I'll
try to reproduce the failure here.
Boaz
On Tue, Jan 29 2008 at 17:36 +0200, Alan Stern <[email protected]> wrote:
> On Tue, 29 Jan 2008, Boaz Harrosh wrote:
>
>> --- a/drivers/usb/storage/transport.c
>> +++ b/drivers/usb/storage/transport.c
>> @@ -462,18 +462,24 @@ static int usb_stor_bulk_transfer_sglist(struct us_data *us, unsigned int pipe,
>> * Common used function. Transfer a complete command
>> * via usb_stor_bulk_transfer_sglist() above. Set cmnd resid
>> */
>> -int usb_stor_bulk_srb(struct us_data* us, unsigned int pipe,
>> - struct scsi_cmnd* srb)
>> +int usb_stor_bulk_srb_length(struct us_data* us, unsigned int pipe,
>> + struct scsi_cmnd* srb, unsigned length)
>> {
>> unsigned int partial;
>> int result = usb_stor_bulk_transfer_sglist(us, pipe, scsi_sglist(srb),
>> - scsi_sg_count(srb), scsi_bufflen(srb),
>> + scsi_sg_count(srb), length,
>> &partial);
>>
>> scsi_set_resid(srb, scsi_bufflen(srb) - partial);
>> return result;
>> }
>>
>> +int usb_stor_bulk_srb(struct us_data* us, unsigned int pipe,
>> + struct scsi_cmnd* srb)
>> +{
>> + return usb_stor_bulk_srb_length(us, pipe, srb, scsi_bufflen(srb));
>> +}
>> +
>
> I don't like this patch very much. Why add another layer of
> indirection when the two subroutines do hardly any work? Leave
> usb_stor_bulk_srb() the way it was, and add usb_stor_bulk_srb_length()
> as a separate routine that simply calls usb_stor_bulk_transfer_sglist()
> and scsi_set_resid().
>
> BTW, the standard coding style calls for a blank line after the list of
> local variables at the start of a function or block.
>
> Alan Stern
>
> -
Me neither, it's not a proper patch just a shut to try and find the reported
bug. I will submit a proper bug later.
Thanks for the review, you are right on all accounts
Boaz
On Tue, 2008-01-29 at 10:36 -0500, Alan Stern wrote:
> On Tue, 29 Jan 2008, Boaz Harrosh wrote:
>
> > --- a/drivers/usb/storage/transport.c
> > +++ b/drivers/usb/storage/transport.c
> > @@ -462,18 +462,24 @@ static int usb_stor_bulk_transfer_sglist(struct us_data *us, unsigned int pipe,
> > * Common used function. Transfer a complete command
> > * via usb_stor_bulk_transfer_sglist() above. Set cmnd resid
> > */
> > -int usb_stor_bulk_srb(struct us_data* us, unsigned int pipe,
> > - struct scsi_cmnd* srb)
> > +int usb_stor_bulk_srb_length(struct us_data* us, unsigned int pipe,
> > + struct scsi_cmnd* srb, unsigned length)
> > {
> > unsigned int partial;
> > int result = usb_stor_bulk_transfer_sglist(us, pipe, scsi_sglist(srb),
> > - scsi_sg_count(srb), scsi_bufflen(srb),
> > + scsi_sg_count(srb), length,
> > &partial);
> >
> > scsi_set_resid(srb, scsi_bufflen(srb) - partial);
> > return result;
> > }
> >
> > +int usb_stor_bulk_srb(struct us_data* us, unsigned int pipe,
> > + struct scsi_cmnd* srb)
> > +{
> > + return usb_stor_bulk_srb_length(us, pipe, srb, scsi_bufflen(srb));
> > +}
> > +
>
> I don't like this patch very much. Why add another layer of
> indirection when the two subroutines do hardly any work? Leave
> usb_stor_bulk_srb() the way it was, and add usb_stor_bulk_srb_length()
> as a separate routine that simply calls usb_stor_bulk_transfer_sglist()
> and scsi_set_resid().
>
> BTW, the standard coding style calls for a blank line after the list of
> local variables at the start of a function or block.
There's another bug in the transport.c conversion in that the residuals
are updated with bogus data in several error cases, since
usb_stor_bulk_transfer_sglist() only sets the actual length if the urb
is actually sent.
I'm not sure if this is is the solution to the problem at hand, but it
definitely fixes another bug in the code.
James
diff --git a/drivers/usb/storage/transport.c b/drivers/usb/storage/transport.c
index d9f4912..bab0858 100644
--- a/drivers/usb/storage/transport.c
+++ b/drivers/usb/storage/transport.c
@@ -465,7 +465,7 @@ static int usb_stor_bulk_transfer_sglist(struct us_data *us, unsigned int pipe,
int usb_stor_bulk_srb(struct us_data* us, unsigned int pipe,
struct scsi_cmnd* srb)
{
- unsigned int partial;
+ unsigned int partial = scsi_get_resid(srb);
int result = usb_stor_bulk_transfer_sglist(us, pipe, scsi_sglist(srb),
scsi_sg_count(srb), scsi_bufflen(srb),
&partial);
Am Dienstag, 29. Januar 2008 16:50:35 schrieb Boaz Harrosh:
> On Tue, Jan 29 2008 at 16:31 +0200, Oliver Neukum <[email protected]> wrote:
> I can not see what it is. Yes CONFIG_USB_STORAGE_DEBUG will help.
> I have a device here that uses the same trasport/protocol I'll
> try to reproduce the failure here.
This is the most common combination of transport and protocol. If it were
broken in a larger number of cases, we'd hear more reports. You'll probably
need the debug output to figure out what's wrong.
Regards
Oliver
On Tue, Jan 29 2008 at 18:34 +0200, James Bottomley <[email protected]> wrote:
> On Tue, 2008-01-29 at 10:36 -0500, Alan Stern wrote:
>> On Tue, 29 Jan 2008, Boaz Harrosh wrote:
>>
>>> --- a/drivers/usb/storage/transport.c
>>> +++ b/drivers/usb/storage/transport.c
>>> @@ -462,18 +462,24 @@ static int usb_stor_bulk_transfer_sglist(struct us_data *us, unsigned int pipe,
>>> * Common used function. Transfer a complete command
>>> * via usb_stor_bulk_transfer_sglist() above. Set cmnd resid
>>> */
>>> -int usb_stor_bulk_srb(struct us_data* us, unsigned int pipe,
>>> - struct scsi_cmnd* srb)
>>> +int usb_stor_bulk_srb_length(struct us_data* us, unsigned int pipe,
>>> + struct scsi_cmnd* srb, unsigned length)
>>> {
>>> unsigned int partial;
>>> int result = usb_stor_bulk_transfer_sglist(us, pipe, scsi_sglist(srb),
>>> - scsi_sg_count(srb), scsi_bufflen(srb),
>>> + scsi_sg_count(srb), length,
>>> &partial);
>>>
>>> scsi_set_resid(srb, scsi_bufflen(srb) - partial);
>>> return result;
>>> }
>>>
>>> +int usb_stor_bulk_srb(struct us_data* us, unsigned int pipe,
>>> + struct scsi_cmnd* srb)
>>> +{
>>> + return usb_stor_bulk_srb_length(us, pipe, srb, scsi_bufflen(srb));
>>> +}
>>> +
>> I don't like this patch very much. Why add another layer of
>> indirection when the two subroutines do hardly any work? Leave
>> usb_stor_bulk_srb() the way it was, and add usb_stor_bulk_srb_length()
>> as a separate routine that simply calls usb_stor_bulk_transfer_sglist()
>> and scsi_set_resid().
>>
>> BTW, the standard coding style calls for a blank line after the list of
>> local variables at the start of a function or block.
>
> There's another bug in the transport.c conversion in that the residuals
> are updated with bogus data in several error cases, since
> usb_stor_bulk_transfer_sglist() only sets the actual length if the urb
> is actually sent.
>
> I'm not sure if this is is the solution to the problem at hand, but it
> definitely fixes another bug in the code.
>
> James
>
> diff --git a/drivers/usb/storage/transport.c b/drivers/usb/storage/transport.c
> index d9f4912..bab0858 100644
> --- a/drivers/usb/storage/transport.c
> +++ b/drivers/usb/storage/transport.c
> @@ -465,7 +465,7 @@ static int usb_stor_bulk_transfer_sglist(struct us_data *us, unsigned int pipe,
> int usb_stor_bulk_srb(struct us_data* us, unsigned int pipe,
> struct scsi_cmnd* srb)
> {
> - unsigned int partial;
> + unsigned int partial = scsi_get_resid(srb);
> int result = usb_stor_bulk_transfer_sglist(us, pipe, scsi_sglist(srb),
> scsi_sg_count(srb), scsi_bufflen(srb),
> &partial);
>
>
> -
But then this is weird because it is not what usb_stor_bulk_transfer_sg() is doing
which was the one called before.
I have such a device and I get one reset but then every thing works nice.
This is with debug on. I'll try to make it fail.
Boaz
On Tue, Jan 29 2008, Jens Axboe wrote:
> On Tue, Jan 29 2008, Oliver Neukum wrote:
> > Am Dienstag, 29. Januar 2008 15:11:08 schrieb Jens Axboe:
> > > On Tue, Jan 29 2008, Boaz Harrosh wrote:
> > > > On Tue, Jan 29 2008 at 15:54 +0200, Jens Axboe <[email protected]> wrote:
> > > > > On Tue, Jan 29 2008, Boaz Harrosh wrote:
> > > > >> Greg KH wrote:
> >
> > > > > No difference, still just a lot of resets.
> > > > >
> > > > Where you able to figure out which usb storage transport is used?
> > > >
> > > > in drivers/usb/storage/usb.c you have get_protocol() and get_transport()
> > > > functions. I'm not sure if these get stored in sysfs perhaps. This will
> > > > pinpoint better where to look. Let me research a bit.
> > >
> > > Did the quick'n easy and dumped it. Protocol is 'Transparent SCSI' and
> > > transport is 'Bulk'
> >
> > You can recompile your kernel with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG
> > That should tell the reason for the resets.
>
> Sure, I'll do that. Will post the results tonight.
OK, fresh boot with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG. Plugged
in the device, waited 10 seconds or so and pulled it out. These are the
messages.
It all looks good until the MODE_SENSE command, where it only transfers
4 of 192 bytes.
usb usb5: usb resume
ehci_hcd 0000:00:1d.7: resume root hub
hub 5-0:1.0: hub_resume
hub 5-0:1.0: state 7 ports 8 chg 0000 evt 0000
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT
hub 5-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 5-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: new high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: default language 0x0409
usb 5-1: uevent
usb 5-1: usb_probe_device
usb 5-1: configuration #1 chosen from 1 choice
usb 5-1: adding 5-1:1.0 (config #1, interface 0)
usb 5-1:1.0: uevent
drivers/usb/core/inode.c: creating file '002'
usb 5-1: new device strings: Mfr=0, Product=3, SerialNumber=4
usb 5-1: Product: Flash Reader
usb 5-1: SerialNumber: 02206
Initializing USB Mass Storage driver...
usb-storage 5-1:1.0: usb_probe_interface
usb-storage 5-1:1.0: usb_probe_interface - got id
usb-storage: USB Mass Storage device detected
usb-storage: -- associate_dev
usb-storage: Vendor: 0x05e3, Product: 0x0760, Revision: 0x0125
usb-storage: Interface Subclass: 0x06, Protocol: 0x50
usb trans Bulk
usb-storage: Transport: Bulk
usb proto Transparent SCSI
usb-storage: Protocol: Transparent SCSI
scsi6 : SCSI emulation for USB Mass Storage devices
usb-storage: *** thread sleeping.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: usb_stor_control_msg: rq=fe rqtype=a1 value=0000 index=00 len=1
usb-storage: GetMaxLUN command result is 1, data is 3
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 00 00 00 24 00
usb-storage: Bulk Command S 0x43425355 T 0x1 L 36 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 36 bytes, 1 entries
usb-storage: Status code 0; transferred 36/36
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x1 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
scsi 6:0:0:0: Direct-Access Generic STORAGE DEVICE 0125 PQ: 0 ANSI: 0
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x2 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x2 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_CAPACITY (10 bytes)
usb-storage: 25 00 00 00 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x3 L 8 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 8 bytes, 1 entries
usb-storage: Status code 0; transferred 8/8
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x3 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
sd 6:0:0:0: [sdb] 4001760 512-byte hardware sectors (2049 MB)
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command MODE_SENSE (6 bytes)
usb-storage: 1a 00 3f 00 c0 00
usb-storage: Bulk Command S 0x43425355 T 0x4 L 192 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 192 bytes, 1 entries
usb-storage: Status code -121; transferred 4/192
usb-storage: -- short read transfer
usb-storage: Bulk data transfer result 0x1
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code -32; transferred 0/13
usb-storage: clearing endpoint halt for pipe 0xc0008280
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=81 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: Attempting to get CSW (2nd try)...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x4 R 188 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
sd 6:0:0:0: [sdb] Write Protect is off
sd 6:0:0:0: [sdb] Mode Sense: 02 00 00 00
sd 6:0:0:0: [sdb] Assuming drive cache: write through
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x5 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x5 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command ALLOW_MEDIUM_REMOVAL (6 bytes)
usb-storage: 1e 00 00 00 01 00
usb-storage: Bulk Command S 0x43425355 T 0x6 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x6 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x7 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x7 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_CAPACITY (10 bytes)
usb-storage: 25 00 00 00 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x8 L 8 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 8 bytes, 1 entries
usb-storage: Status code 0; transferred 8/8
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x8 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
sd 6:0:0:0: [sdb] 4001760 512-byte hardware sectors (2049 MB)
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command MODE_SENSE (6 bytes)
usb-storage: 1a 00 3f 00 c0 00
usb-storage: Bulk Command S 0x43425355 T 0x9 L 192 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 192 bytes, 1 entries
usb-storage: Status code -121; transferred 4/192
usb-storage: -- short read transfer
usb-storage: Bulk data transfer result 0x1
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code -32; transferred 0/13
usb-storage: clearing endpoint halt for pipe 0xc0008280
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=81 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: Attempting to get CSW (2nd try)...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x9 R 188 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
sd 6:0:0:0: [sdb] Write Protect is off
sd 6:0:0:0: [sdb] Mode Sense: 02 00 00 00
sd 6:0:0:0: [sdb] Assuming drive cache: write through
sdb:<7>usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 00 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0xa L 4096 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code 0; transferred 4096/4096
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0xa R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
sdb1
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command ALLOW_MEDIUM_REMOVAL (6 bytes)
usb-storage: 1e 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0xb L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0xb R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
sd 6:0:0:0: [sdb] Attached SCSI removable disk
sd 6:0:0:0: Attached scsi generic sg1 type 0
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 00 00 00 24 00
usb-storage: Bulk Command S 0x43425355 T 0xc L 36 F 128 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 36 bytes, 1 entries
usb-storage: Status code 0; transferred 36/36
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0xc R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
scsi 6:0:0:1: Direct-Access Generic STORAGE DEVICE 0125 PQ: 0 ANSI: 0
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0xd L 0 F 0 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0xd R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0xe L 18 F 128 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: usb_sg_init returned -22
usb-storage: Bulk data transfer result 0x4
usb-storage: -- auto-sense failure
usb-storage: storage_pre_reset
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: reset high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb-storage: storage_post_reset
usb-storage: usb_reset_composite_device returns 0
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0xf L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0xf R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x10 L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: usb_sg_init returned -22
usb-storage: Bulk data transfer result 0x4
usb-storage: -- auto-sense failure
usb-storage: storage_pre_reset
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: reset high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb-storage: storage_post_reset
usb-storage: usb_reset_composite_device returns 0
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x11 L 0 F 0 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x11 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x12 L 18 F 128 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: usb_sg_init returned -22
usb-storage: Bulk data transfer result 0x4
usb-storage: -- auto-sense failure
usb-storage: storage_pre_reset
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: reset high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb-storage: storage_post_reset
usb-storage: usb_reset_composite_device returns 0
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x13 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x13 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x14 L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: usb_sg_init returned -22
usb-storage: Bulk data transfer result 0x4
usb-storage: -- auto-sense failure
usb-storage: storage_pre_reset
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: reset high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb-storage: storage_post_reset
usb-storage: usb_reset_composite_device returns 0
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x15 L 0 F 0 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x15 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x16 L 18 F 128 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: usb_sg_init returned -22
usb-storage: Bulk data transfer result 0x4
usb-storage: -- auto-sense failure
usb-storage: storage_pre_reset
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: reset high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb-storage: storage_post_reset
usb-storage: usb_reset_composite_device returns 0
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x17 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x17 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x18 L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: usb_sg_init returned -22
usb-storage: Bulk data transfer result 0x4
usb-storage: -- auto-sense failure
usb-storage: storage_pre_reset
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: reset high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb-storage: storage_post_reset
usb-storage: usb_reset_composite_device returns 0
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x19 L 0 F 0 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x19 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x1a L 18 F 128 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: usb_sg_init returned -22
usb-storage: Bulk data transfer result 0x4
usb-storage: -- auto-sense failure
usb-storage: storage_pre_reset
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: reset high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb-storage: storage_post_reset
usb-storage: usb_reset_composite_device returns 0
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x1b L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x1b R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x1c L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: usb_sg_init returned -22
usb-storage: Bulk data transfer result 0x4
usb-storage: -- auto-sense failure
usb-storage: storage_pre_reset
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: reset high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb-storage: storage_post_reset
usb-storage: usb_reset_composite_device returns 0
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x1d L 0 F 0 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x1d R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x1e L 18 F 128 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: usb_sg_init returned -22
usb-storage: Bulk data transfer result 0x4
usb-storage: -- auto-sense failure
usb-storage: storage_pre_reset
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: reset high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb-storage: storage_post_reset
usb-storage: usb_reset_composite_device returns 0
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x1f L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x1f R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x20 L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: usb_sg_init returned -22
usb-storage: Bulk data transfer result 0x4
usb-storage: -- auto-sense failure
usb-storage: storage_pre_reset
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: reset high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb-storage: storage_post_reset
usb-storage: usb_reset_composite_device returns 0
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x21 L 0 F 0 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x21 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x22 L 18 F 128 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: usb_sg_init returned -22
usb-storage: Bulk data transfer result 0x4
usb-storage: -- auto-sense failure
usb-storage: storage_pre_reset
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: reset high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb-storage: storage_post_reset
usb-storage: usb_reset_composite_device returns 0
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x23 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x23 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x24 L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: usb_sg_init returned -22
usb-storage: Bulk data transfer result 0x4
usb-storage: -- auto-sense failure
usb-storage: storage_pre_reset
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: reset high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb-storage: storage_post_reset
usb-storage: usb_reset_composite_device returns 0
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_CAPACITY (10 bytes)
usb-storage: 25 00 00 00 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x25 L 8 F 128 Trg 0 LUN 1 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 8 bytes, 1 entries
usb-storage: Status code -32; transferred 0/8
usb-storage: clearing endpoint halt for pipe 0xc0008280
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=81 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: Bulk data transfer result 0x2
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x25 R 8 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: -- unexpectedly short transfer
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x26 L 18 F 128 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: Status code -75; transferred 0/18
usb-storage: -- babble
usb-storage: Bulk data transfer result 0x3
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code -75; transferred 0/13
usb-storage: -- babble
usb-storage: Bulk status result = 3
usb-storage: -- auto-sense failure
usb-storage: storage_pre_reset
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: reset high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb-storage: storage_post_reset
usb-storage: usb_reset_composite_device returns 0
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x27 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x27 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x28 L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: usb_sg_init returned -22
usb-storage: Bulk data transfer result 0x4
usb-storage: -- auto-sense failure
usb-storage: storage_pre_reset
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: reset high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb-storage: storage_post_reset
usb-storage: usb_reset_composite_device returns 0
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_CAPACITY (10 bytes)
usb-storage: 25 00 00 00 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x29 L 8 F 128 Trg 0 LUN 1 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 8 bytes, 1 entries
usb-storage: Status code -32; transferred 0/8
usb-storage: clearing endpoint halt for pipe 0xc0008280
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=81 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: Bulk data transfer result 0x2
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x29 R 8 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: -- unexpectedly short transfer
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x2a L 18 F 128 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: Status code -75; transferred 0/18
usb-storage: -- babble
usb-storage: Bulk data transfer result 0x3
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code -75; transferred 0/13
usb-storage: -- babble
usb-storage: Bulk status result = 3
usb-storage: -- auto-sense failure
usb-storage: storage_pre_reset
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: reset high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb-storage: storage_post_reset
usb-storage: usb_reset_composite_device returns 0
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x2b L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x2b R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x2c L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: usb_sg_init returned -22
usb-storage: Bulk data transfer result 0x4
usb-storage: -- auto-sense failure
usb-storage: storage_pre_reset
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: reset high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb-storage: storage_post_reset
usb-storage: usb_reset_composite_device returns 0
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_CAPACITY (10 bytes)
usb-storage: 25 00 00 00 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x2d L 8 F 128 Trg 0 LUN 1 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 8 bytes, 1 entries
usb-storage: Status code -32; transferred 0/8
usb-storage: clearing endpoint halt for pipe 0xc0008280
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=81 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: Bulk data transfer result 0x2
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x2d R 8 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: -- unexpectedly short transfer
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x2e L 18 F 128 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: Status code -75; transferred 0/18
usb-storage: -- babble
usb-storage: Bulk data transfer result 0x3
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code -75; transferred 0/13
usb-storage: -- babble
usb-storage: Bulk status result = 3
usb-storage: -- auto-sense failure
usb-storage: storage_pre_reset
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: reset high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb-storage: storage_post_reset
usb-storage: usb_reset_composite_device returns 0
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x2f L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x2f R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x30 L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: usb_sg_init returned -22
usb-storage: Bulk data transfer result 0x4
usb-storage: -- auto-sense failure
usb-storage: storage_pre_reset
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: reset high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb-storage: storage_post_reset
usb-storage: usb_reset_composite_device returns 0
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_CAPACITY (10 bytes)
usb-storage: 25 00 00 00 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x31 L 8 F 128 Trg 0 LUN 1 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 8 bytes, 1 entries
usb-storage: Status code -32; transferred 0/8
usb-storage: clearing endpoint halt for pipe 0xc0008280
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=81 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: Bulk data transfer result 0x2
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x31 R 8 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: -- unexpectedly short transfer
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x32 L 18 F 128 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: Status code -75; transferred 0/18
usb-storage: -- babble
usb-storage: Bulk data transfer result 0x3
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code -75; transferred 0/13
usb-storage: -- babble
usb-storage: Bulk status result = 3
usb-storage: -- auto-sense failure
usb-storage: storage_pre_reset
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: reset high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb-storage: storage_post_reset
usb-storage: usb_reset_composite_device returns 0
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x33 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x33 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x34 L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: usb_sg_init returned -22
usb-storage: Bulk data transfer result 0x4
usb-storage: -- auto-sense failure
usb-storage: storage_pre_reset
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: reset high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb-storage: storage_post_reset
usb-storage: usb_reset_composite_device returns 0
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_CAPACITY (10 bytes)
usb-storage: 25 00 00 00 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x35 L 8 F 128 Trg 0 LUN 1 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 8 bytes, 1 entries
usb-storage: Status code -32; transferred 0/8
usb-storage: clearing endpoint halt for pipe 0xc0008280
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=81 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: Bulk data transfer result 0x2
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x35 R 8 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: -- unexpectedly short transfer
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x36 L 18 F 128 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: Status code -75; transferred 0/18
usb-storage: -- babble
usb-storage: Bulk data transfer result 0x3
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code -75; transferred 0/13
usb-storage: -- babble
usb-storage: Bulk status result = 3
usb-storage: -- auto-sense failure
usb-storage: storage_pre_reset
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: reset high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb-storage: storage_post_reset
usb-storage: usb_reset_composite_device returns 0
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x37 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x37 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x38 L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: usb_sg_init returned -22
usb-storage: Bulk data transfer result 0x4
usb-storage: -- auto-sense failure
usb-storage: storage_pre_reset
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: reset high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb-storage: storage_post_reset
usb-storage: usb_reset_composite_device returns 0
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_CAPACITY (10 bytes)
usb-storage: 25 00 00 00 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x39 L 8 F 128 Trg 0 LUN 1 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 8 bytes, 1 entries
usb-storage: Status code -32; transferred 0/8
usb-storage: clearing endpoint halt for pipe 0xc0008280
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=81 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: Bulk data transfer result 0x2
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x39 R 8 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: -- unexpectedly short transfer
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x3a L 18 F 128 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: Status code -75; transferred 0/18
usb-storage: -- babble
usb-storage: Bulk data transfer result 0x3
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code -75; transferred 0/13
usb-storage: -- babble
usb-storage: Bulk status result = 3
usb-storage: -- auto-sense failure
usb-storage: storage_pre_reset
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 5-1: reset high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb-storage: storage_post_reset
usb-storage: usb_reset_composite_device returns 0
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x3b L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x3b R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x3c L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: usb_sg_init returned -22
usb-storage: Bulk data transfer result 0x4
usb-storage: -- auto-sense failure
usb-storage: storage_pre_reset
ehci_hcd 0000:00:1d.7: port 1 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
hub 5-0:1.0: state 7 ports 8 chg 0000 evt 0002
usb 5-1: reset high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:1d.7: devpath 1 ep0in 3strikes
ehci_hcd 0000:00:1d.7: devpath 1 ep0in 3strikes
ehci_hcd 0000:00:1d.7: devpath 1 ep0in 3strikes
ehci_hcd 0000:00:1d.7: devpath 1 ep0in 3strikes
ehci_hcd 0000:00:1d.7: devpath 1 ep0in 3strikes
ehci_hcd 0000:00:1d.7: devpath 1 ep0in 3strikes
ehci_hcd 0000:00:1d.7: devpath 1 ep0in 3strikes
ehci_hcd 0000:00:1d.7: devpath 1 ep0in 3strikes
ehci_hcd 0000:00:1d.7: devpath 1 ep0in 3strikes
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001002 POWER sig=se0 CSC
hub 5-0:1.0: logical disconnect on port 1
usb-storage: storage_post_reset
usb-storage: usb_reset_composite_device returns -19
usb-storage: usb_stor_Bulk_reset called
usb-storage: usb_stor_control_msg: rq=ff rqtype=21 value=0000 index=00 len=0
usb-storage: Soft reset failed: -19
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
hub 5-0:1.0: state 7 ports 8 chg 0002 evt 0002
hub 5-0:1.0: port 1, status 0100, change 0000, 12 Mb/s
usb 5-1: USB disconnect, address 2
usb 5-1: unregistering device
usb 5-1: usb_disable_device nuking all URBs
usb 5-1: unregistering interface 5-1:1.0
usb-storage: storage_disconnect() called
usb-storage: usb_stor_stop_transport called
usb-storage: queuecommand called
usb-storage: Fail command during disconnect
usb-storage: queuecommand called
usb-storage: Fail command during disconnect
sd 6:0:0:1: [sdc] READ CAPACITY failed
sd 6:0:0:1: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_OK
sd 6:0:0:1: [sdc] Sense not available.
usb-storage: queuecommand called
usb-storage: Fail command during disconnect
sd 6:0:0:1: [sdc] Write Protect is off
sd 6:0:0:1: [sdc] Mode Sense: 00 00 00 00
sd 6:0:0:1: [sdc] Assuming drive cache: write through
sd 6:0:0:1: [sdc] Attached SCSI removable disk
sd 6:0:0:1: Attached scsi generic sg2 type 0
usb-storage: queuecommand called
usb-storage: Fail command during disconnect
usb-storage: queuecommand called
usb-storage: Fail command during disconnect
usb-storage: queuecommand called
usb-storage: Fail command during disconnect
sd 6:0:0:0: [sdb] READ CAPACITY failed
sd 6:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_OK
sd 6:0:0:0: [sdb] Sense not available.
usb-storage: queuecommand called
usb-storage: Fail command during disconnect
usb-storage: *** thread awakened.
usb-storage: -- exiting
usb-storage: queuecommand called
usb-storage: Fail command during disconnect
sd 6:0:0:0: [sdb] Write Protect is off
sd 6:0:0:0: [sdb] Mode Sense: 00 00 00 00
sd 6:0:0:0: [sdb] Assuming drive cache: write through
usb-storage: queuecommand called
usb-storage: Fail command during disconnect
usb-storage: queuecommand called
usb-storage: Fail command during disconnect
usb-storage: queuecommand called
usb-storage: Fail command during disconnect
usb-storage: queuecommand called
usb-storage: Fail command during disconnect
usb-storage: queuecommand called
usb-storage: Fail command during disconnect
usb-storage: queuecommand called
usb-storage: Fail command during disconnect
usb-storage: queuecommand called
usb-storage: Fail command during disconnect
usb-storage: queuecommand called
usb-storage: Fail command during disconnect
usb-storage: queuecommand called
usb-storage: Fail command during disconnect
usb-storage: queuecommand called
usb-storage: Fail command during disconnect
usb-storage: queuecommand called
usb-storage: Fail command during disconnect
usb-storage: device scan complete
usb-storage: -- usb_stor_release_resources
usb-storage: -- sending exit command to thread
scsi 6:0:0:0: [sdb] READ CAPACITY failed
scsi 6:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_OK
scsi 6:0:0:0: [sdb] Sense not available.
scsi 6:0:0:0: rejecting I/O to dead device
scsi 6:0:0:0: [sdb] Write Protect is off
scsi 6:0:0:0: [sdb] Mode Sense: 00 00 00 00
scsi 6:0:0:0: [sdb] Assuming drive cache: write through
scsi 6:0:0:0: rejecting I/O to dead device
usb-storage: -- dissociate_dev
usb 5-1:1.0: uevent
usb 5-1: uevent
hub 5-0:1.0: hub_suspend
usb usb5: bus auto-suspend
ehci_hcd 0000:00:1d.7: suspend root hub
--
Jens Axboe
On Tue, 2008-01-29 at 20:27 +0200, Boaz Harrosh wrote:
> On Tue, Jan 29 2008 at 18:34 +0200, James Bottomley <[email protected]> wrote:
> > On Tue, 2008-01-29 at 10:36 -0500, Alan Stern wrote:
> >> On Tue, 29 Jan 2008, Boaz Harrosh wrote:
> >>
> >>> --- a/drivers/usb/storage/transport.c
> >>> +++ b/drivers/usb/storage/transport.c
> >>> @@ -462,18 +462,24 @@ static int usb_stor_bulk_transfer_sglist(struct us_data *us, unsigned int pipe,
> >>> * Common used function. Transfer a complete command
> >>> * via usb_stor_bulk_transfer_sglist() above. Set cmnd resid
> >>> */
> >>> -int usb_stor_bulk_srb(struct us_data* us, unsigned int pipe,
> >>> - struct scsi_cmnd* srb)
> >>> +int usb_stor_bulk_srb_length(struct us_data* us, unsigned int pipe,
> >>> + struct scsi_cmnd* srb, unsigned length)
> >>> {
> >>> unsigned int partial;
> >>> int result = usb_stor_bulk_transfer_sglist(us, pipe, scsi_sglist(srb),
> >>> - scsi_sg_count(srb), scsi_bufflen(srb),
> >>> + scsi_sg_count(srb), length,
> >>> &partial);
> >>>
> >>> scsi_set_resid(srb, scsi_bufflen(srb) - partial);
> >>> return result;
> >>> }
> >>>
> >>> +int usb_stor_bulk_srb(struct us_data* us, unsigned int pipe,
> >>> + struct scsi_cmnd* srb)
> >>> +{
> >>> + return usb_stor_bulk_srb_length(us, pipe, srb, scsi_bufflen(srb));
> >>> +}
> >>> +
> >> I don't like this patch very much. Why add another layer of
> >> indirection when the two subroutines do hardly any work? Leave
> >> usb_stor_bulk_srb() the way it was, and add usb_stor_bulk_srb_length()
> >> as a separate routine that simply calls usb_stor_bulk_transfer_sglist()
> >> and scsi_set_resid().
> >>
> >> BTW, the standard coding style calls for a blank line after the list of
> >> local variables at the start of a function or block.
> >
> > There's another bug in the transport.c conversion in that the residuals
> > are updated with bogus data in several error cases, since
> > usb_stor_bulk_transfer_sglist() only sets the actual length if the urb
> > is actually sent.
> >
> > I'm not sure if this is is the solution to the problem at hand, but it
> > definitely fixes another bug in the code.
> >
> > James
> >
> > diff --git a/drivers/usb/storage/transport.c b/drivers/usb/storage/transport.c
> > index d9f4912..bab0858 100644
> > --- a/drivers/usb/storage/transport.c
> > +++ b/drivers/usb/storage/transport.c
> > @@ -465,7 +465,7 @@ static int usb_stor_bulk_transfer_sglist(struct us_data *us, unsigned int pipe,
> > int usb_stor_bulk_srb(struct us_data* us, unsigned int pipe,
> > struct scsi_cmnd* srb)
> > {
> > - unsigned int partial;
> > + unsigned int partial = scsi_get_resid(srb);
> > int result = usb_stor_bulk_transfer_sglist(us, pipe, scsi_sglist(srb),
> > scsi_sg_count(srb), scsi_bufflen(srb),
> > &partial);
> >
> >
> > -
> But then this is weird because it is not what usb_stor_bulk_transfer_sg() is doing
> which was the one called before.
Um, yes it was. The original code did this
sb_stor_bulk_transfer_sg(..., &srp->resid, ...)
Which was at liberty not to touch resid, which it chose not to do in the
error legs.
Your new code does
int partial; <- stack uninitialised
sb_stor_bulk_transfer_sglist(..., &partial, ...);
scsi_set_resid(srb, scsi_bufflen(srb) - partial);
If the function doesn't touch partial, as it doesn't in the error legs,
resid now gets set with rubbish.
Actually, my code is still wrong .. we have to set it to
scsi_bufflen(srb) - scsi_resid(srb) so that it comes back the same if
left untouched.
> I have such a device and I get one reset but then every thing works nice.
> This is with debug on. I'll try to make it fail.
James
On Tue, Jan 29 2008 at 20:48 +0200, James Bottomley <[email protected]> wrote:
> On Tue, 2008-01-29 at 20:27 +0200, Boaz Harrosh wrote:
>> On Tue, Jan 29 2008 at 18:34 +0200, James Bottomley <[email protected]> wrote:
>>> On Tue, 2008-01-29 at 10:36 -0500, Alan Stern wrote:
>>>> On Tue, 29 Jan 2008, Boaz Harrosh wrote:
>>>>
>>>>> --- a/drivers/usb/storage/transport.c
>>>>> +++ b/drivers/usb/storage/transport.c
>>>>> @@ -462,18 +462,24 @@ static int usb_stor_bulk_transfer_sglist(struct us_data *us, unsigned int pipe,
>>>>> * Common used function. Transfer a complete command
>>>>> * via usb_stor_bulk_transfer_sglist() above. Set cmnd resid
>>>>> */
>>>>> -int usb_stor_bulk_srb(struct us_data* us, unsigned int pipe,
>>>>> - struct scsi_cmnd* srb)
>>>>> +int usb_stor_bulk_srb_length(struct us_data* us, unsigned int pipe,
>>>>> + struct scsi_cmnd* srb, unsigned length)
>>>>> {
>>>>> unsigned int partial;
>>>>> int result = usb_stor_bulk_transfer_sglist(us, pipe, scsi_sglist(srb),
>>>>> - scsi_sg_count(srb), scsi_bufflen(srb),
>>>>> + scsi_sg_count(srb), length,
>>>>> &partial);
>>>>>
>>>>> scsi_set_resid(srb, scsi_bufflen(srb) - partial);
>>>>> return result;
>>>>> }
>>>>>
>>>>> +int usb_stor_bulk_srb(struct us_data* us, unsigned int pipe,
>>>>> + struct scsi_cmnd* srb)
>>>>> +{
>>>>> + return usb_stor_bulk_srb_length(us, pipe, srb, scsi_bufflen(srb));
>>>>> +}
>>>>> +
>>>> I don't like this patch very much. Why add another layer of
>>>> indirection when the two subroutines do hardly any work? Leave
>>>> usb_stor_bulk_srb() the way it was, and add usb_stor_bulk_srb_length()
>>>> as a separate routine that simply calls usb_stor_bulk_transfer_sglist()
>>>> and scsi_set_resid().
>>>>
>>>> BTW, the standard coding style calls for a blank line after the list of
>>>> local variables at the start of a function or block.
>>> There's another bug in the transport.c conversion in that the residuals
>>> are updated with bogus data in several error cases, since
>>> usb_stor_bulk_transfer_sglist() only sets the actual length if the urb
>>> is actually sent.
>>>
>>> I'm not sure if this is is the solution to the problem at hand, but it
>>> definitely fixes another bug in the code.
>>>
>>> James
>>>
>>> diff --git a/drivers/usb/storage/transport.c b/drivers/usb/storage/transport.c
>>> index d9f4912..bab0858 100644
>>> --- a/drivers/usb/storage/transport.c
>>> +++ b/drivers/usb/storage/transport.c
>>> @@ -465,7 +465,7 @@ static int usb_stor_bulk_transfer_sglist(struct us_data *us, unsigned int pipe,
>>> int usb_stor_bulk_srb(struct us_data* us, unsigned int pipe,
>>> struct scsi_cmnd* srb)
>>> {
>>> - unsigned int partial;
>>> + unsigned int partial = scsi_get_resid(srb);
>>> int result = usb_stor_bulk_transfer_sglist(us, pipe, scsi_sglist(srb),
>>> scsi_sg_count(srb), scsi_bufflen(srb),
>>> &partial);
>>>
>>>
>>> -
>> But then this is weird because it is not what usb_stor_bulk_transfer_sg() is doing
>> which was the one called before.
>
> Um, yes it was. The original code did this
>
> sb_stor_bulk_transfer_sg(..., &srp->resid, ...)
>
> Which was at liberty not to touch resid, which it chose not to do in the
> error legs.
>
> Your new code does
>
> int partial; <- stack uninitialised
> sb_stor_bulk_transfer_sglist(..., &partial, ...);
> scsi_set_resid(srb, scsi_bufflen(srb) - partial);
>
> If the function doesn't touch partial, as it doesn't in the error legs,
> resid now gets set with rubbish.
>
> Actually, my code is still wrong .. we have to set it to
> scsi_bufflen(srb) - scsi_resid(srb) so that it comes back the same if
> left untouched.
>
>> I have such a device and I get one reset but then every thing works nice.
>> This is with debug on. I'll try to make it fail.
>
> James
>
>
Sorry I still don't see it.
original code did sb_stor_bulk_transfer_sg(..., &srp->resid, ...)
but sb_stor_bulk_transfer_sg does the:
int partial; <- stack uninitialised
sb_stor_bulk_transfer_sglist(..., &partial, ...);
and then unconditionally sets *residual = length_left;
I do not see an "error legs" case in sb_stor_bulk_transfer_sg().
I have just cut and pasted the !use_sg from sb_stor_bulk_transfer_sg names
and all
Boaz
On Tue, Jan 29 2008 at 20:39 +0200, Jens Axboe <[email protected]> wrote:
> On Tue, Jan 29 2008, Jens Axboe wrote:
>> On Tue, Jan 29 2008, Oliver Neukum wrote:
>>> Am Dienstag, 29. Januar 2008 15:11:08 schrieb Jens Axboe:
>>>> On Tue, Jan 29 2008, Boaz Harrosh wrote:
>>>>> On Tue, Jan 29 2008 at 15:54 +0200, Jens Axboe <[email protected]> wrote:
>>>>>> On Tue, Jan 29 2008, Boaz Harrosh wrote:
>>>>>>> Greg KH wrote:
>>>
>>>>>> No difference, still just a lot of resets.
>>>>>>
>>>>> Where you able to figure out which usb storage transport is used?
>>>>>
>>>>> in drivers/usb/storage/usb.c you have get_protocol() and get_transport()
>>>>> functions. I'm not sure if these get stored in sysfs perhaps. This will
>>>>> pinpoint better where to look. Let me research a bit.
>>>> Did the quick'n easy and dumped it. Protocol is 'Transparent SCSI' and
>>>> transport is 'Bulk'
>>> You can recompile your kernel with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG
>>> That should tell the reason for the resets.
>> Sure, I'll do that. Will post the results tonight.
>
> OK, fresh boot with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG. Plugged
> in the device, waited 10 seconds or so and pulled it out. These are the
> messages.
>
> It all looks good until the MODE_SENSE command, where it only transfers
> 4 of 192 bytes.
>
<snip>
> usb-storage: Command MODE_SENSE (6 bytes)
> usb-storage: 1a 00 3f 00 c0 00
> usb-storage: Bulk Command S 0x43425355 T 0x4 L 192 F 128 Trg 0 LUN 0 CL 6
> usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
> usb-storage: Status code 0; transferred 31/31
> usb-storage: -- transfer complete
> usb-storage: Bulk command transfer result=0
> usb-storage: usb_stor_bulk_transfer_sglist: xfer 192 bytes, 1 entries
> usb-storage: Status code -121; transferred 4/192
> usb-storage: -- short read transfer
> usb-storage: Bulk data transfer result 0x1
> usb-storage: Attempting to get CSW...
<snip>
I get something similar but better:
usb-storage: Command MODE_SENSE (6 bytes)
usb-storage: 1a 00 3f 00 c0 00
usb-storage: Bulk Command S 0x43425355 T 0x6 L 192 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 192 bytes, 1 entries
usb-storage: Status code -121; transferred 36/192
usb-storage: -- short read transfer
usb-storage: Bulk data transfer result 0x1
usb-storage: Attempting to get CSW...
So I get 36 bytes, then code goes on into one reset, and every thing is then
fine.
Could you put us out of our mesery and revert that patch:
[SCSI] usb: transport - convert to accessors and !use_sg code path removal
(6d416e6173394defda5933e419e805b696681b7e)
to make sure this is it. I hate to do this to you, but I cannot reproduce the
failure down here. If it works please send a log with the debugs on perhaps
we can compare.
You will need to configure out the CONFIG_USB_STORAG_* they will not compile
you should have only have CONFIG_USB_STORAGE & CONFIG_USB_STORAGE_DEBUG. it should
support your HW.
Thanks Jens
Boaz
On Tue, Jan 29, 2008 at 07:39:11PM +0100, Jens Axboe wrote:
> On Tue, Jan 29 2008, Jens Axboe wrote:
> > On Tue, Jan 29 2008, Oliver Neukum wrote:
> > > Am Dienstag, 29. Januar 2008 15:11:08 schrieb Jens Axboe:
> > > > On Tue, Jan 29 2008, Boaz Harrosh wrote:
> > > > > On Tue, Jan 29 2008 at 15:54 +0200, Jens Axboe <[email protected]> wrote:
> > > > > > On Tue, Jan 29 2008, Boaz Harrosh wrote:
> > > > > >> Greg KH wrote:
> > >
> > > > > > No difference, still just a lot of resets.
> > > > > >
> > > > > Where you able to figure out which usb storage transport is used?
> > > > >
> > > > > in drivers/usb/storage/usb.c you have get_protocol() and get_transport()
> > > > > functions. I'm not sure if these get stored in sysfs perhaps. This will
> > > > > pinpoint better where to look. Let me research a bit.
> > > >
> > > > Did the quick'n easy and dumped it. Protocol is 'Transparent SCSI' and
> > > > transport is 'Bulk'
> > >
> > > You can recompile your kernel with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG
> > > That should tell the reason for the resets.
> >
> > Sure, I'll do that. Will post the results tonight.
>
> OK, fresh boot with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG. Plugged
> in the device, waited 10 seconds or so and pulled it out. These are the
> messages.
>
> It all looks good until the MODE_SENSE command, where it only transfers
> 4 of 192 bytes.
No, that's not the problem. This is the problem:
> usb-storage: *** thread awakened.
> usb-storage: Command TEST_UNIT_READY (6 bytes)
> usb-storage: 00 00 00 00 00 00
> usb-storage: Bulk Command S 0x43425355 T 0xd L 0 F 0 Trg 0 LUN 1 CL 6
> usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
> usb-storage: Status code 0; transferred 31/31
> usb-storage: -- transfer complete
> usb-storage: Bulk command transfer result=0
> usb-storage: Attempting to get CSW...
> usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
> usb-storage: Status code 0; transferred 13/13
> usb-storage: -- transfer complete
> usb-storage: Bulk status result = 0
> usb-storage: Bulk Status S 0x53425355 T 0xd R 0 Stat 0x1
> usb-storage: -- transport indicates command failure
> usb-storage: Issuing auto-REQUEST_SENSE
> usb-storage: Bulk Command S 0x43425355 T 0xe L 18 F 128 Trg 0 LUN 1 CL 6
> usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
> usb-storage: Status code 0; transferred 31/31
> usb-storage: -- transfer complete
> usb-storage: Bulk command transfer result=0
> usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
> usb-storage: usb_sg_init returned -22
> usb-storage: Bulk data transfer result 0x4
> usb-storage: -- auto-sense failure
> usb-storage: storage_pre_reset
> ehci_hcd 0000:00:1d.7: port 1 high speed
> ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> ehci_hcd 0000:00:1d.7: port 1 high speed
> ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
> usb-storage: storage_post_reset
> usb-storage: usb_reset_composite_device returns 0
> usb-storage: scsi cmd done, result=0x70000
> usb-storage: *** thread sleeping.
For some reason, usb_sg_init is boned during auto-sense.
Matt
--
Matthew Dharm Home: [email protected]
Maintainer, Linux USB Mass Storage Driver
It was a new hope.
-- Dust Puppy
User Friendly, 12/25/1998
On Tue, Jan 29 2008, Matthew Dharm wrote:
> On Tue, Jan 29, 2008 at 07:39:11PM +0100, Jens Axboe wrote:
> > On Tue, Jan 29 2008, Jens Axboe wrote:
> > > On Tue, Jan 29 2008, Oliver Neukum wrote:
> > > > Am Dienstag, 29. Januar 2008 15:11:08 schrieb Jens Axboe:
> > > > > On Tue, Jan 29 2008, Boaz Harrosh wrote:
> > > > > > On Tue, Jan 29 2008 at 15:54 +0200, Jens Axboe <[email protected]> wrote:
> > > > > > > On Tue, Jan 29 2008, Boaz Harrosh wrote:
> > > > > > >> Greg KH wrote:
> > > >
> > > > > > > No difference, still just a lot of resets.
> > > > > > >
> > > > > > Where you able to figure out which usb storage transport is used?
> > > > > >
> > > > > > in drivers/usb/storage/usb.c you have get_protocol() and get_transport()
> > > > > > functions. I'm not sure if these get stored in sysfs perhaps. This will
> > > > > > pinpoint better where to look. Let me research a bit.
> > > > >
> > > > > Did the quick'n easy and dumped it. Protocol is 'Transparent SCSI' and
> > > > > transport is 'Bulk'
> > > >
> > > > You can recompile your kernel with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG
> > > > That should tell the reason for the resets.
> > >
> > > Sure, I'll do that. Will post the results tonight.
> >
> > OK, fresh boot with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG. Plugged
> > in the device, waited 10 seconds or so and pulled it out. These are the
> > messages.
> >
> > It all looks good until the MODE_SENSE command, where it only transfers
> > 4 of 192 bytes.
>
> No, that's not the problem. This is the problem:
It's where the problem starts, otherwise there would not be a need to
sense :-)
> > usb-storage: *** thread awakened.
> > usb-storage: Command TEST_UNIT_READY (6 bytes)
> > usb-storage: 00 00 00 00 00 00
> > usb-storage: Bulk Command S 0x43425355 T 0xd L 0 F 0 Trg 0 LUN 1 CL 6
> > usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
> > usb-storage: Status code 0; transferred 31/31
> > usb-storage: -- transfer complete
> > usb-storage: Bulk command transfer result=0
> > usb-storage: Attempting to get CSW...
> > usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
> > usb-storage: Status code 0; transferred 13/13
> > usb-storage: -- transfer complete
> > usb-storage: Bulk status result = 0
> > usb-storage: Bulk Status S 0x53425355 T 0xd R 0 Stat 0x1
> > usb-storage: -- transport indicates command failure
> > usb-storage: Issuing auto-REQUEST_SENSE
> > usb-storage: Bulk Command S 0x43425355 T 0xe L 18 F 128 Trg 0 LUN 1 CL 6
> > usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
> > usb-storage: Status code 0; transferred 31/31
> > usb-storage: -- transfer complete
> > usb-storage: Bulk command transfer result=0
> > usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
> > usb-storage: usb_sg_init returned -22
> > usb-storage: Bulk data transfer result 0x4
> > usb-storage: -- auto-sense failure
> > usb-storage: storage_pre_reset
> > ehci_hcd 0000:00:1d.7: port 1 high speed
> > ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
> > usb 5-1: reset high speed USB device using ehci_hcd and address 2
> > ehci_hcd 0000:00:1d.7: port 1 high speed
> > ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
> > usb-storage: storage_post_reset
> > usb-storage: usb_reset_composite_device returns 0
> > usb-storage: scsi cmd done, result=0x70000
> > usb-storage: *** thread sleeping.
>
> For some reason, usb_sg_init is boned during auto-sense.
My guess would be that sg == NULL, hence the -EINVAL.
--
Jens Axboe
On Tue, 2008-01-29 at 20:58 +0200, Boaz Harrosh wrote:
> > Your new code does
> >
> > int partial; <- stack uninitialised
> > sb_stor_bulk_transfer_sglist(..., &partial, ...);
> > scsi_set_resid(srb, scsi_bufflen(srb) - partial);
> >
> > If the function doesn't touch partial, as it doesn't in the error legs,
> > resid now gets set with rubbish.
> >
> > Actually, my code is still wrong .. we have to set it to
> > scsi_bufflen(srb) - scsi_resid(srb) so that it comes back the same if
> > left untouched.
> >
> >> I have such a device and I get one reset but then every thing works nice.
> >> This is with debug on. I'll try to make it fail.
> >
> > James
> >
> >
> Sorry I still don't see it.
>
> original code did sb_stor_bulk_transfer_sg(..., &srp->resid, ...)
>
> but sb_stor_bulk_transfer_sg does the:
> int partial; <- stack uninitialised
> sb_stor_bulk_transfer_sglist(..., &partial, ...);
>
> and then unconditionally sets *residual = length_left;
> I do not see an "error legs" case in sb_stor_bulk_transfer_sg().
This is really programming 101. This:
static int usb_stor_bulk_transfer_sglist(struct us_data *us, unsigned
int pipe,
struct scatterlist *sg, int num_sg, unsigned int length,
unsigned int *act_len)
{
int result;
/* don't submit s-g requests during abort/disconnect processing */
if (us->flags & ABORTING_OR_DISCONNECTING)
return USB_STOR_XFER_ERROR;
The return USB_STOR_XFER_ERROR; is called an error leg. It returns
without updating *act_len thus leaving &partial uninitialised.
James
On Tue, Jan 29 2008, Jens Axboe wrote:
> On Tue, Jan 29 2008, Matthew Dharm wrote:
> > On Tue, Jan 29, 2008 at 07:39:11PM +0100, Jens Axboe wrote:
> > > On Tue, Jan 29 2008, Jens Axboe wrote:
> > > > On Tue, Jan 29 2008, Oliver Neukum wrote:
> > > > > Am Dienstag, 29. Januar 2008 15:11:08 schrieb Jens Axboe:
> > > > > > On Tue, Jan 29 2008, Boaz Harrosh wrote:
> > > > > > > On Tue, Jan 29 2008 at 15:54 +0200, Jens Axboe <[email protected]> wrote:
> > > > > > > > On Tue, Jan 29 2008, Boaz Harrosh wrote:
> > > > > > > >> Greg KH wrote:
> > > > >
> > > > > > > > No difference, still just a lot of resets.
> > > > > > > >
> > > > > > > Where you able to figure out which usb storage transport is used?
> > > > > > >
> > > > > > > in drivers/usb/storage/usb.c you have get_protocol() and get_transport()
> > > > > > > functions. I'm not sure if these get stored in sysfs perhaps. This will
> > > > > > > pinpoint better where to look. Let me research a bit.
> > > > > >
> > > > > > Did the quick'n easy and dumped it. Protocol is 'Transparent SCSI' and
> > > > > > transport is 'Bulk'
> > > > >
> > > > > You can recompile your kernel with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG
> > > > > That should tell the reason for the resets.
> > > >
> > > > Sure, I'll do that. Will post the results tonight.
> > >
> > > OK, fresh boot with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG. Plugged
> > > in the device, waited 10 seconds or so and pulled it out. These are the
> > > messages.
> > >
> > > It all looks good until the MODE_SENSE command, where it only transfers
> > > 4 of 192 bytes.
> >
> > No, that's not the problem. This is the problem:
>
> It's where the problem starts, otherwise there would not be a need to
> sense :-)
>
> > > usb-storage: *** thread awakened.
> > > usb-storage: Command TEST_UNIT_READY (6 bytes)
> > > usb-storage: 00 00 00 00 00 00
> > > usb-storage: Bulk Command S 0x43425355 T 0xd L 0 F 0 Trg 0 LUN 1 CL 6
> > > usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
> > > usb-storage: Status code 0; transferred 31/31
> > > usb-storage: -- transfer complete
> > > usb-storage: Bulk command transfer result=0
> > > usb-storage: Attempting to get CSW...
> > > usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
> > > usb-storage: Status code 0; transferred 13/13
> > > usb-storage: -- transfer complete
> > > usb-storage: Bulk status result = 0
> > > usb-storage: Bulk Status S 0x53425355 T 0xd R 0 Stat 0x1
> > > usb-storage: -- transport indicates command failure
> > > usb-storage: Issuing auto-REQUEST_SENSE
> > > usb-storage: Bulk Command S 0x43425355 T 0xe L 18 F 128 Trg 0 LUN 1 CL 6
> > > usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
> > > usb-storage: Status code 0; transferred 31/31
> > > usb-storage: -- transfer complete
> > > usb-storage: Bulk command transfer result=0
> > > usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
> > > usb-storage: usb_sg_init returned -22
> > > usb-storage: Bulk data transfer result 0x4
> > > usb-storage: -- auto-sense failure
> > > usb-storage: storage_pre_reset
> > > ehci_hcd 0000:00:1d.7: port 1 high speed
> > > ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
> > > usb 5-1: reset high speed USB device using ehci_hcd and address 2
> > > ehci_hcd 0000:00:1d.7: port 1 high speed
> > > ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
> > > usb-storage: storage_post_reset
> > > usb-storage: usb_reset_composite_device returns 0
> > > usb-storage: scsi cmd done, result=0x70000
> > > usb-storage: *** thread sleeping.
> >
> > For some reason, usb_sg_init is boned during auto-sense.
>
> My guess would be that sg == NULL, hence the -EINVAL.
Yep, trace below:
WARNING: at drivers/usb/storage/transport.c:426
usb_stor_bulk_transfer_sglist()
Pid: 12536, comm: usb-storage Not tainted 2.6.24 #74
[<7810541a>] show_trace_log_lvl+0x1a/0x30
[<78105e82>] show_trace+0x12/0x20
[<7810689c>] dump_stack+0x6c/0x80
[<f83e267e>] usb_stor_bulk_transfer_sglist+0x14e/0x160 [usb_storage]
[<f83e2730>] usb_stor_bulk_srb_length+0x30/0x50 [usb_storage]
[<f83e2762>] usb_stor_bulk_srb+0x12/0x20 [usb_storage]
[<f83e2ce0>] usb_stor_Bulk_transport+0x190/0x3d0 [usb_storage]
[<f83e30d6>] usb_stor_invoke_transport+0x1b6/0x320 [usb_storage]
[<f83e1a38>] usb_stor_transparent_scsi_command+0x8/0x10 [usb_storage]
[<f83e3813>] usb_stor_control_thread+0x143/0x2c0 [usb_storage]
[<7813bc02>] kthread+0x42/0x70
[<78104fab>] kernel_thread_helper+0x7/0x1c
=======================
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries, sg
00000000
usb-storage: usb_sg_init returned -22
--
Jens Axboe
On Tue, Jan 29 2008 at 21:17 +0200, James Bottomley <[email protected]> wrote:
> On Tue, 2008-01-29 at 20:58 +0200, Boaz Harrosh wrote:
>>> Your new code does
>>>
>>> int partial; <- stack uninitialised
>>> sb_stor_bulk_transfer_sglist(..., &partial, ...);
>>> scsi_set_resid(srb, scsi_bufflen(srb) - partial);
>>>
>>> If the function doesn't touch partial, as it doesn't in the error legs,
>>> resid now gets set with rubbish.
>>>
>>> Actually, my code is still wrong .. we have to set it to
>>> scsi_bufflen(srb) - scsi_resid(srb) so that it comes back the same if
>>> left untouched.
>>>
>>>> I have such a device and I get one reset but then every thing works nice.
>>>> This is with debug on. I'll try to make it fail.
>>> James
>>>
>>>
>> Sorry I still don't see it.
>>
>> original code did sb_stor_bulk_transfer_sg(..., &srp->resid, ...)
>>
>> but sb_stor_bulk_transfer_sg does the:
>> int partial; <- stack uninitialised
>> sb_stor_bulk_transfer_sglist(..., &partial, ...);
>>
>> and then unconditionally sets *residual = length_left;
>> I do not see an "error legs" case in sb_stor_bulk_transfer_sg().
>
> This is really programming 101. This:
>
> static int usb_stor_bulk_transfer_sglist(struct us_data *us, unsigned
> int pipe,
> struct scatterlist *sg, int num_sg, unsigned int length,
> unsigned int *act_len)
> {
> int result;
>
> /* don't submit s-g requests during abort/disconnect processing */
> if (us->flags & ABORTING_OR_DISCONNECTING)
> return USB_STOR_XFER_ERROR;
>
> The return USB_STOR_XFER_ERROR; is called an error leg. It returns
> without updating *act_len thus leaving &partial uninitialised.
>
> James
>
Yes you are right this is a bug, but it is a bug that was there before.
perhaps the stack is just different now then what it used to be.
Jens could you please try that:
diff --git a/drivers/usb/storage/transport.c b/drivers/usb/storage/transport.c
index d9f4912..b18a5e6 100644
--- a/drivers/usb/storage/transport.c
+++ b/drivers/usb/storage/transport.c
@@ -465,7 +465,7 @@ static int usb_stor_bulk_transfer_sglist(struct us_data *us, unsigned int pipe,
int usb_stor_bulk_srb(struct us_data* us, unsigned int pipe,
struct scsi_cmnd* srb)
{
- unsigned int partial;
+ unsigned int partial = 0;
int result = usb_stor_bulk_transfer_sglist(us, pipe, scsi_sglist(srb),
scsi_sg_count(srb), scsi_bufflen(srb),
&partial);
On Tue, 2008-01-29 at 11:10 -0800, Matthew Dharm wrote:
> On Tue, Jan 29, 2008 at 07:39:11PM +0100, Jens Axboe wrote:
> > On Tue, Jan 29 2008, Jens Axboe wrote:
> > > On Tue, Jan 29 2008, Oliver Neukum wrote:
> > > > Am Dienstag, 29. Januar 2008 15:11:08 schrieb Jens Axboe:
> > > > > On Tue, Jan 29 2008, Boaz Harrosh wrote:
> > > > > > On Tue, Jan 29 2008 at 15:54 +0200, Jens Axboe <[email protected]> wrote:
> > > > > > > On Tue, Jan 29 2008, Boaz Harrosh wrote:
> > > > > > >> Greg KH wrote:
> > > >
> > > > > > > No difference, still just a lot of resets.
> > > > > > >
> > > > > > Where you able to figure out which usb storage transport is used?
> > > > > >
> > > > > > in drivers/usb/storage/usb.c you have get_protocol() and get_transport()
> > > > > > functions. I'm not sure if these get stored in sysfs perhaps. This will
> > > > > > pinpoint better where to look. Let me research a bit.
> > > > >
> > > > > Did the quick'n easy and dumped it. Protocol is 'Transparent SCSI' and
> > > > > transport is 'Bulk'
> > > >
> > > > You can recompile your kernel with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG
> > > > That should tell the reason for the resets.
> > >
> > > Sure, I'll do that. Will post the results tonight.
> >
> > OK, fresh boot with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG. Plugged
> > in the device, waited 10 seconds or so and pulled it out. These are the
> > messages.
> >
> > It all looks good until the MODE_SENSE command, where it only transfers
> > 4 of 192 bytes.
>
> No, that's not the problem. This is the problem:
>
> > usb-storage: *** thread awakened.
> > usb-storage: Command TEST_UNIT_READY (6 bytes)
> > usb-storage: 00 00 00 00 00 00
> > usb-storage: Bulk Command S 0x43425355 T 0xd L 0 F 0 Trg 0 LUN 1 CL 6
> > usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
> > usb-storage: Status code 0; transferred 31/31
> > usb-storage: -- transfer complete
> > usb-storage: Bulk command transfer result=0
> > usb-storage: Attempting to get CSW...
> > usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
> > usb-storage: Status code 0; transferred 13/13
> > usb-storage: -- transfer complete
> > usb-storage: Bulk status result = 0
> > usb-storage: Bulk Status S 0x53425355 T 0xd R 0 Stat 0x1
> > usb-storage: -- transport indicates command failure
> > usb-storage: Issuing auto-REQUEST_SENSE
> > usb-storage: Bulk Command S 0x43425355 T 0xe L 18 F 128 Trg 0 LUN 1 CL 6
> > usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
> > usb-storage: Status code 0; transferred 31/31
> > usb-storage: -- transfer complete
> > usb-storage: Bulk command transfer result=0
> > usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
> > usb-storage: usb_sg_init returned -22
> > usb-storage: Bulk data transfer result 0x4
> > usb-storage: -- auto-sense failure
> > usb-storage: storage_pre_reset
> > ehci_hcd 0000:00:1d.7: port 1 high speed
> > ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
> > usb 5-1: reset high speed USB device using ehci_hcd and address 2
> > ehci_hcd 0000:00:1d.7: port 1 high speed
> > ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
> > usb-storage: storage_post_reset
> > usb-storage: usb_reset_composite_device returns 0
> > usb-storage: scsi cmd done, result=0x70000
> > usb-storage: *** thread sleeping.
>
> For some reason, usb_sg_init is boned during auto-sense.
OK, that's implicating the scsi_eh_prep_cmnd() in the auto sense
code ... that was also an update in 2.6.24
James
On Tue, Jan 29 2008, James Bottomley wrote:
> On Tue, 2008-01-29 at 11:10 -0800, Matthew Dharm wrote:
> > On Tue, Jan 29, 2008 at 07:39:11PM +0100, Jens Axboe wrote:
> > > On Tue, Jan 29 2008, Jens Axboe wrote:
> > > > On Tue, Jan 29 2008, Oliver Neukum wrote:
> > > > > Am Dienstag, 29. Januar 2008 15:11:08 schrieb Jens Axboe:
> > > > > > On Tue, Jan 29 2008, Boaz Harrosh wrote:
> > > > > > > On Tue, Jan 29 2008 at 15:54 +0200, Jens Axboe <[email protected]> wrote:
> > > > > > > > On Tue, Jan 29 2008, Boaz Harrosh wrote:
> > > > > > > >> Greg KH wrote:
> > > > >
> > > > > > > > No difference, still just a lot of resets.
> > > > > > > >
> > > > > > > Where you able to figure out which usb storage transport is used?
> > > > > > >
> > > > > > > in drivers/usb/storage/usb.c you have get_protocol() and get_transport()
> > > > > > > functions. I'm not sure if these get stored in sysfs perhaps. This will
> > > > > > > pinpoint better where to look. Let me research a bit.
> > > > > >
> > > > > > Did the quick'n easy and dumped it. Protocol is 'Transparent SCSI' and
> > > > > > transport is 'Bulk'
> > > > >
> > > > > You can recompile your kernel with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG
> > > > > That should tell the reason for the resets.
> > > >
> > > > Sure, I'll do that. Will post the results tonight.
> > >
> > > OK, fresh boot with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG. Plugged
> > > in the device, waited 10 seconds or so and pulled it out. These are the
> > > messages.
> > >
> > > It all looks good until the MODE_SENSE command, where it only transfers
> > > 4 of 192 bytes.
> >
> > No, that's not the problem. This is the problem:
> >
> > > usb-storage: *** thread awakened.
> > > usb-storage: Command TEST_UNIT_READY (6 bytes)
> > > usb-storage: 00 00 00 00 00 00
> > > usb-storage: Bulk Command S 0x43425355 T 0xd L 0 F 0 Trg 0 LUN 1 CL 6
> > > usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
> > > usb-storage: Status code 0; transferred 31/31
> > > usb-storage: -- transfer complete
> > > usb-storage: Bulk command transfer result=0
> > > usb-storage: Attempting to get CSW...
> > > usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
> > > usb-storage: Status code 0; transferred 13/13
> > > usb-storage: -- transfer complete
> > > usb-storage: Bulk status result = 0
> > > usb-storage: Bulk Status S 0x53425355 T 0xd R 0 Stat 0x1
> > > usb-storage: -- transport indicates command failure
> > > usb-storage: Issuing auto-REQUEST_SENSE
> > > usb-storage: Bulk Command S 0x43425355 T 0xe L 18 F 128 Trg 0 LUN 1 CL 6
> > > usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
> > > usb-storage: Status code 0; transferred 31/31
> > > usb-storage: -- transfer complete
> > > usb-storage: Bulk command transfer result=0
> > > usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
> > > usb-storage: usb_sg_init returned -22
> > > usb-storage: Bulk data transfer result 0x4
> > > usb-storage: -- auto-sense failure
> > > usb-storage: storage_pre_reset
> > > ehci_hcd 0000:00:1d.7: port 1 high speed
> > > ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
> > > usb 5-1: reset high speed USB device using ehci_hcd and address 2
> > > ehci_hcd 0000:00:1d.7: port 1 high speed
> > > ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
> > > usb-storage: storage_post_reset
> > > usb-storage: usb_reset_composite_device returns 0
> > > usb-storage: scsi cmd done, result=0x70000
> > > usb-storage: *** thread sleeping.
> >
> > For some reason, usb_sg_init is boned during auto-sense.
>
> OK, that's implicating the scsi_eh_prep_cmnd() in the auto sense
> code ... that was also an update in 2.6.24
yeah, already found the bug - it's assuming ->request_buffer holds the
sglist, oops. Preparing a fix.
--
Jens Axboe
On Tue, Jan 29, 2008 at 08:15:04PM +0100, Jens Axboe wrote:
> On Tue, Jan 29 2008, Matthew Dharm wrote:
> > On Tue, Jan 29, 2008 at 07:39:11PM +0100, Jens Axboe wrote:
> > > On Tue, Jan 29 2008, Jens Axboe wrote:
> > > > On Tue, Jan 29 2008, Oliver Neukum wrote:
> > > > > Am Dienstag, 29. Januar 2008 15:11:08 schrieb Jens Axboe:
> > > > > > On Tue, Jan 29 2008, Boaz Harrosh wrote:
> > > > > > > On Tue, Jan 29 2008 at 15:54 +0200, Jens Axboe <[email protected]> wrote:
> > > > > > > > On Tue, Jan 29 2008, Boaz Harrosh wrote:
> > > > > > > >> Greg KH wrote:
> > > > >
> > > > > > > > No difference, still just a lot of resets.
> > > > > > > >
> > > > > > > Where you able to figure out which usb storage transport is used?
> > > > > > >
> > > > > > > in drivers/usb/storage/usb.c you have get_protocol() and get_transport()
> > > > > > > functions. I'm not sure if these get stored in sysfs perhaps. This will
> > > > > > > pinpoint better where to look. Let me research a bit.
> > > > > >
> > > > > > Did the quick'n easy and dumped it. Protocol is 'Transparent SCSI' and
> > > > > > transport is 'Bulk'
> > > > >
> > > > > You can recompile your kernel with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG
> > > > > That should tell the reason for the resets.
> > > >
> > > > Sure, I'll do that. Will post the results tonight.
> > >
> > > OK, fresh boot with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG. Plugged
> > > in the device, waited 10 seconds or so and pulled it out. These are the
> > > messages.
> > >
> > > It all looks good until the MODE_SENSE command, where it only transfers
> > > 4 of 192 bytes.
> >
> > No, that's not the problem. This is the problem:
>
> It's where the problem starts, otherwise there would not be a need to
> sense :-)
MODE_SENSE has nothing to do with it. A short MODE_SENSE response is
perfectly valid, and the log shows it was handled correctly and subsequent
commands worked just fine. It's not until the TUR fails that we get the
problem.
Matt
--
Matthew Dharm Home: [email protected]
Maintainer, Linux USB Mass Storage Driver
P: Nine more messages in admin.policy.
M: I know, I'm typing as fast as I can!
-- Pitr and Mike
User Friendly, 11/27/97
On Tue, Jan 29 2008, Jens Axboe wrote:
> On Tue, Jan 29 2008, James Bottomley wrote:
> > On Tue, 2008-01-29 at 11:10 -0800, Matthew Dharm wrote:
> > > On Tue, Jan 29, 2008 at 07:39:11PM +0100, Jens Axboe wrote:
> > > > On Tue, Jan 29 2008, Jens Axboe wrote:
> > > > > On Tue, Jan 29 2008, Oliver Neukum wrote:
> > > > > > Am Dienstag, 29. Januar 2008 15:11:08 schrieb Jens Axboe:
> > > > > > > On Tue, Jan 29 2008, Boaz Harrosh wrote:
> > > > > > > > On Tue, Jan 29 2008 at 15:54 +0200, Jens Axboe <[email protected]> wrote:
> > > > > > > > > On Tue, Jan 29 2008, Boaz Harrosh wrote:
> > > > > > > > >> Greg KH wrote:
> > > > > >
> > > > > > > > > No difference, still just a lot of resets.
> > > > > > > > >
> > > > > > > > Where you able to figure out which usb storage transport is used?
> > > > > > > >
> > > > > > > > in drivers/usb/storage/usb.c you have get_protocol() and get_transport()
> > > > > > > > functions. I'm not sure if these get stored in sysfs perhaps. This will
> > > > > > > > pinpoint better where to look. Let me research a bit.
> > > > > > >
> > > > > > > Did the quick'n easy and dumped it. Protocol is 'Transparent SCSI' and
> > > > > > > transport is 'Bulk'
> > > > > >
> > > > > > You can recompile your kernel with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG
> > > > > > That should tell the reason for the resets.
> > > > >
> > > > > Sure, I'll do that. Will post the results tonight.
> > > >
> > > > OK, fresh boot with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG. Plugged
> > > > in the device, waited 10 seconds or so and pulled it out. These are the
> > > > messages.
> > > >
> > > > It all looks good until the MODE_SENSE command, where it only transfers
> > > > 4 of 192 bytes.
> > >
> > > No, that's not the problem. This is the problem:
> > >
> > > > usb-storage: *** thread awakened.
> > > > usb-storage: Command TEST_UNIT_READY (6 bytes)
> > > > usb-storage: 00 00 00 00 00 00
> > > > usb-storage: Bulk Command S 0x43425355 T 0xd L 0 F 0 Trg 0 LUN 1 CL 6
> > > > usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
> > > > usb-storage: Status code 0; transferred 31/31
> > > > usb-storage: -- transfer complete
> > > > usb-storage: Bulk command transfer result=0
> > > > usb-storage: Attempting to get CSW...
> > > > usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
> > > > usb-storage: Status code 0; transferred 13/13
> > > > usb-storage: -- transfer complete
> > > > usb-storage: Bulk status result = 0
> > > > usb-storage: Bulk Status S 0x53425355 T 0xd R 0 Stat 0x1
> > > > usb-storage: -- transport indicates command failure
> > > > usb-storage: Issuing auto-REQUEST_SENSE
> > > > usb-storage: Bulk Command S 0x43425355 T 0xe L 18 F 128 Trg 0 LUN 1 CL 6
> > > > usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
> > > > usb-storage: Status code 0; transferred 31/31
> > > > usb-storage: -- transfer complete
> > > > usb-storage: Bulk command transfer result=0
> > > > usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
> > > > usb-storage: usb_sg_init returned -22
> > > > usb-storage: Bulk data transfer result 0x4
> > > > usb-storage: -- auto-sense failure
> > > > usb-storage: storage_pre_reset
> > > > ehci_hcd 0000:00:1d.7: port 1 high speed
> > > > ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
> > > > usb 5-1: reset high speed USB device using ehci_hcd and address 2
> > > > ehci_hcd 0000:00:1d.7: port 1 high speed
> > > > ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
> > > > usb-storage: storage_post_reset
> > > > usb-storage: usb_reset_composite_device returns 0
> > > > usb-storage: scsi cmd done, result=0x70000
> > > > usb-storage: *** thread sleeping.
> > >
> > > For some reason, usb_sg_init is boned during auto-sense.
> >
> > OK, that's implicating the scsi_eh_prep_cmnd() in the auto sense
> > code ... that was also an update in 2.6.24
>
> yeah, already found the bug - it's assuming ->request_buffer holds the
> sglist, oops. Preparing a fix.
ok here goes, this saves and restores the sg table correctly. it also
fixes the usb bug for me.
diff --git a/drivers/scsi/scsi_error.c b/drivers/scsi/scsi_error.c
index 547e85a..12770ef 100644
--- a/drivers/scsi/scsi_error.c
+++ b/drivers/scsi/scsi_error.c
@@ -622,13 +622,15 @@ void scsi_eh_prep_cmnd(struct scsi_cmnd *scmd, struct scsi_eh_save *ses,
ses->use_sg = scmd->use_sg;
ses->resid = scmd->resid;
ses->result = scmd->result;
+ memcpy(&ses->sense_sgl, &scmd->sg_table, sizeof(ses->sense_sgl));
if (sense_bytes) {
scmd->request_bufflen = min_t(unsigned,
SCSI_SENSE_BUFFERSIZE, sense_bytes);
sg_init_one(&ses->sense_sgl, scmd->sense_buffer,
scmd->request_bufflen);
- scmd->request_buffer = &ses->sense_sgl;
+ scmd->sg_table.sgl = &ses->sense_sgl;
+ scmd->sg_table.nents = scmd->sg_table.orig_nents = 1;
scmd->sc_data_direction = DMA_FROM_DEVICE;
scmd->use_sg = 1;
memset(scmd->cmnd, 0, sizeof(scmd->cmnd));
@@ -679,6 +681,7 @@ void scsi_eh_restore_cmnd(struct scsi_cmnd* scmd, struct scsi_eh_save *ses)
scmd->request_bufflen = ses->bufflen;
scmd->request_buffer = ses->buffer;
scmd->use_sg = ses->use_sg;
+ memcpy(&scmd->sg_table, &ses->sg_table, sizeof(scmd->sg_table));
scmd->resid = ses->resid;
scmd->result = ses->result;
}
diff --git a/include/scsi/scsi_eh.h b/include/scsi/scsi_eh.h
index d21b891..d43dc83 100644
--- a/include/scsi/scsi_eh.h
+++ b/include/scsi/scsi_eh.h
@@ -75,6 +75,7 @@ struct scsi_eh_save {
void *buffer;
unsigned bufflen;
+ struct sg_table sg_table;
unsigned short use_sg;
int resid;
--
Jens Axboe
On Tue, Jan 29 2008 at 21:45 +0200, Jens Axboe <[email protected]> wrote:
> On Tue, Jan 29 2008, Jens Axboe wrote:
>> On Tue, Jan 29 2008, James Bottomley wrote:
>>> On Tue, 2008-01-29 at 11:10 -0800, Matthew Dharm wrote:
>>>> On Tue, Jan 29, 2008 at 07:39:11PM +0100, Jens Axboe wrote:
>>>>> On Tue, Jan 29 2008, Jens Axboe wrote:
>>>>>> On Tue, Jan 29 2008, Oliver Neukum wrote:
>>>>>>> Am Dienstag, 29. Januar 2008 15:11:08 schrieb Jens Axboe:
>>>>>>>> On Tue, Jan 29 2008, Boaz Harrosh wrote:
>>>>>>>>> On Tue, Jan 29 2008 at 15:54 +0200, Jens Axboe <[email protected]> wrote:
>>>>>>>>>> On Tue, Jan 29 2008, Boaz Harrosh wrote:
>>>>>>>>>>> Greg KH wrote:
>>>>>>>
>>>>>>>>>> No difference, still just a lot of resets.
>>>>>>>>>>
>>>>>>>>> Where you able to figure out which usb storage transport is used?
>>>>>>>>>
>>>>>>>>> in drivers/usb/storage/usb.c you have get_protocol() and get_transport()
>>>>>>>>> functions. I'm not sure if these get stored in sysfs perhaps. This will
>>>>>>>>> pinpoint better where to look. Let me research a bit.
>>>>>>>> Did the quick'n easy and dumped it. Protocol is 'Transparent SCSI' and
>>>>>>>> transport is 'Bulk'
>>>>>>> You can recompile your kernel with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG
>>>>>>> That should tell the reason for the resets.
>>>>>> Sure, I'll do that. Will post the results tonight.
>>>>> OK, fresh boot with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG. Plugged
>>>>> in the device, waited 10 seconds or so and pulled it out. These are the
>>>>> messages.
>>>>>
>>>>> It all looks good until the MODE_SENSE command, where it only transfers
>>>>> 4 of 192 bytes.
>>>> No, that's not the problem. This is the problem:
>>>>
>>>>> usb-storage: *** thread awakened.
>>>>> usb-storage: Command TEST_UNIT_READY (6 bytes)
>>>>> usb-storage: 00 00 00 00 00 00
>>>>> usb-storage: Bulk Command S 0x43425355 T 0xd L 0 F 0 Trg 0 LUN 1 CL 6
>>>>> usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
>>>>> usb-storage: Status code 0; transferred 31/31
>>>>> usb-storage: -- transfer complete
>>>>> usb-storage: Bulk command transfer result=0
>>>>> usb-storage: Attempting to get CSW...
>>>>> usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
>>>>> usb-storage: Status code 0; transferred 13/13
>>>>> usb-storage: -- transfer complete
>>>>> usb-storage: Bulk status result = 0
>>>>> usb-storage: Bulk Status S 0x53425355 T 0xd R 0 Stat 0x1
>>>>> usb-storage: -- transport indicates command failure
>>>>> usb-storage: Issuing auto-REQUEST_SENSE
>>>>> usb-storage: Bulk Command S 0x43425355 T 0xe L 18 F 128 Trg 0 LUN 1 CL 6
>>>>> usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
>>>>> usb-storage: Status code 0; transferred 31/31
>>>>> usb-storage: -- transfer complete
>>>>> usb-storage: Bulk command transfer result=0
>>>>> usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
>>>>> usb-storage: usb_sg_init returned -22
>>>>> usb-storage: Bulk data transfer result 0x4
>>>>> usb-storage: -- auto-sense failure
>>>>> usb-storage: storage_pre_reset
>>>>> ehci_hcd 0000:00:1d.7: port 1 high speed
>>>>> ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
>>>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
>>>>> ehci_hcd 0000:00:1d.7: port 1 high speed
>>>>> ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
>>>>> usb-storage: storage_post_reset
>>>>> usb-storage: usb_reset_composite_device returns 0
>>>>> usb-storage: scsi cmd done, result=0x70000
>>>>> usb-storage: *** thread sleeping.
>>>> For some reason, usb_sg_init is boned during auto-sense.
>>> OK, that's implicating the scsi_eh_prep_cmnd() in the auto sense
>>> code ... that was also an update in 2.6.24
>> yeah, already found the bug - it's assuming ->request_buffer holds the
>> sglist, oops. Preparing a fix.
>
> ok here goes, this saves and restores the sg table correctly. it also
> fixes the usb bug for me.
>
> diff --git a/drivers/scsi/scsi_error.c b/drivers/scsi/scsi_error.c
> index 547e85a..12770ef 100644
> --- a/drivers/scsi/scsi_error.c
> +++ b/drivers/scsi/scsi_error.c
> @@ -622,13 +622,15 @@ void scsi_eh_prep_cmnd(struct scsi_cmnd *scmd, struct scsi_eh_save *ses,
> ses->use_sg = scmd->use_sg;
> ses->resid = scmd->resid;
> ses->result = scmd->result;
> + memcpy(&ses->sense_sgl, &scmd->sg_table, sizeof(ses->sense_sgl));
>
> if (sense_bytes) {
> scmd->request_bufflen = min_t(unsigned,
> SCSI_SENSE_BUFFERSIZE, sense_bytes);
> sg_init_one(&ses->sense_sgl, scmd->sense_buffer,
> scmd->request_bufflen);
> - scmd->request_buffer = &ses->sense_sgl;
> + scmd->sg_table.sgl = &ses->sense_sgl;
> + scmd->sg_table.nents = scmd->sg_table.orig_nents = 1;
> scmd->sc_data_direction = DMA_FROM_DEVICE;
> scmd->use_sg = 1;
> memset(scmd->cmnd, 0, sizeof(scmd->cmnd));
> @@ -679,6 +681,7 @@ void scsi_eh_restore_cmnd(struct scsi_cmnd* scmd, struct scsi_eh_save *ses)
> scmd->request_bufflen = ses->bufflen;
> scmd->request_buffer = ses->buffer;
> scmd->use_sg = ses->use_sg;
> + memcpy(&scmd->sg_table, &ses->sg_table, sizeof(scmd->sg_table));
> scmd->resid = ses->resid;
> scmd->result = ses->result;
> }
> diff --git a/include/scsi/scsi_eh.h b/include/scsi/scsi_eh.h
> index d21b891..d43dc83 100644
> --- a/include/scsi/scsi_eh.h
> +++ b/include/scsi/scsi_eh.h
> @@ -75,6 +75,7 @@ struct scsi_eh_save {
>
> void *buffer;
> unsigned bufflen;
> + struct sg_table sg_table;
> unsigned short use_sg;
> int resid;
>
>
Ok this is not in Linus tree is it? Hence I did not have that failure.
Boaz
On Tue, Jan 29 2008, Boaz Harrosh wrote:
> On Tue, Jan 29 2008 at 21:45 +0200, Jens Axboe <[email protected]> wrote:
> > On Tue, Jan 29 2008, Jens Axboe wrote:
> >> On Tue, Jan 29 2008, James Bottomley wrote:
> >>> On Tue, 2008-01-29 at 11:10 -0800, Matthew Dharm wrote:
> >>>> On Tue, Jan 29, 2008 at 07:39:11PM +0100, Jens Axboe wrote:
> >>>>> On Tue, Jan 29 2008, Jens Axboe wrote:
> >>>>>> On Tue, Jan 29 2008, Oliver Neukum wrote:
> >>>>>>> Am Dienstag, 29. Januar 2008 15:11:08 schrieb Jens Axboe:
> >>>>>>>> On Tue, Jan 29 2008, Boaz Harrosh wrote:
> >>>>>>>>> On Tue, Jan 29 2008 at 15:54 +0200, Jens Axboe <[email protected]> wrote:
> >>>>>>>>>> On Tue, Jan 29 2008, Boaz Harrosh wrote:
> >>>>>>>>>>> Greg KH wrote:
> >>>>>>>
> >>>>>>>>>> No difference, still just a lot of resets.
> >>>>>>>>>>
> >>>>>>>>> Where you able to figure out which usb storage transport is used?
> >>>>>>>>>
> >>>>>>>>> in drivers/usb/storage/usb.c you have get_protocol() and get_transport()
> >>>>>>>>> functions. I'm not sure if these get stored in sysfs perhaps. This will
> >>>>>>>>> pinpoint better where to look. Let me research a bit.
> >>>>>>>> Did the quick'n easy and dumped it. Protocol is 'Transparent SCSI' and
> >>>>>>>> transport is 'Bulk'
> >>>>>>> You can recompile your kernel with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG
> >>>>>>> That should tell the reason for the resets.
> >>>>>> Sure, I'll do that. Will post the results tonight.
> >>>>> OK, fresh boot with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG. Plugged
> >>>>> in the device, waited 10 seconds or so and pulled it out. These are the
> >>>>> messages.
> >>>>>
> >>>>> It all looks good until the MODE_SENSE command, where it only transfers
> >>>>> 4 of 192 bytes.
> >>>> No, that's not the problem. This is the problem:
> >>>>
> >>>>> usb-storage: *** thread awakened.
> >>>>> usb-storage: Command TEST_UNIT_READY (6 bytes)
> >>>>> usb-storage: 00 00 00 00 00 00
> >>>>> usb-storage: Bulk Command S 0x43425355 T 0xd L 0 F 0 Trg 0 LUN 1 CL 6
> >>>>> usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
> >>>>> usb-storage: Status code 0; transferred 31/31
> >>>>> usb-storage: -- transfer complete
> >>>>> usb-storage: Bulk command transfer result=0
> >>>>> usb-storage: Attempting to get CSW...
> >>>>> usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
> >>>>> usb-storage: Status code 0; transferred 13/13
> >>>>> usb-storage: -- transfer complete
> >>>>> usb-storage: Bulk status result = 0
> >>>>> usb-storage: Bulk Status S 0x53425355 T 0xd R 0 Stat 0x1
> >>>>> usb-storage: -- transport indicates command failure
> >>>>> usb-storage: Issuing auto-REQUEST_SENSE
> >>>>> usb-storage: Bulk Command S 0x43425355 T 0xe L 18 F 128 Trg 0 LUN 1 CL 6
> >>>>> usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
> >>>>> usb-storage: Status code 0; transferred 31/31
> >>>>> usb-storage: -- transfer complete
> >>>>> usb-storage: Bulk command transfer result=0
> >>>>> usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
> >>>>> usb-storage: usb_sg_init returned -22
> >>>>> usb-storage: Bulk data transfer result 0x4
> >>>>> usb-storage: -- auto-sense failure
> >>>>> usb-storage: storage_pre_reset
> >>>>> ehci_hcd 0000:00:1d.7: port 1 high speed
> >>>>> ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
> >>>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> >>>>> ehci_hcd 0000:00:1d.7: port 1 high speed
> >>>>> ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
> >>>>> usb-storage: storage_post_reset
> >>>>> usb-storage: usb_reset_composite_device returns 0
> >>>>> usb-storage: scsi cmd done, result=0x70000
> >>>>> usb-storage: *** thread sleeping.
> >>>> For some reason, usb_sg_init is boned during auto-sense.
> >>> OK, that's implicating the scsi_eh_prep_cmnd() in the auto sense
> >>> code ... that was also an update in 2.6.24
> >> yeah, already found the bug - it's assuming ->request_buffer holds the
> >> sglist, oops. Preparing a fix.
> >
> > ok here goes, this saves and restores the sg table correctly. it also
> > fixes the usb bug for me.
> >
> > diff --git a/drivers/scsi/scsi_error.c b/drivers/scsi/scsi_error.c
> > index 547e85a..12770ef 100644
> > --- a/drivers/scsi/scsi_error.c
> > +++ b/drivers/scsi/scsi_error.c
> > @@ -622,13 +622,15 @@ void scsi_eh_prep_cmnd(struct scsi_cmnd *scmd, struct scsi_eh_save *ses,
> > ses->use_sg = scmd->use_sg;
> > ses->resid = scmd->resid;
> > ses->result = scmd->result;
> > + memcpy(&ses->sense_sgl, &scmd->sg_table, sizeof(ses->sense_sgl));
> >
> > if (sense_bytes) {
> > scmd->request_bufflen = min_t(unsigned,
> > SCSI_SENSE_BUFFERSIZE, sense_bytes);
> > sg_init_one(&ses->sense_sgl, scmd->sense_buffer,
> > scmd->request_bufflen);
> > - scmd->request_buffer = &ses->sense_sgl;
> > + scmd->sg_table.sgl = &ses->sense_sgl;
> > + scmd->sg_table.nents = scmd->sg_table.orig_nents = 1;
> > scmd->sc_data_direction = DMA_FROM_DEVICE;
> > scmd->use_sg = 1;
> > memset(scmd->cmnd, 0, sizeof(scmd->cmnd));
> > @@ -679,6 +681,7 @@ void scsi_eh_restore_cmnd(struct scsi_cmnd* scmd, struct scsi_eh_save *ses)
> > scmd->request_bufflen = ses->bufflen;
> > scmd->request_buffer = ses->buffer;
> > scmd->use_sg = ses->use_sg;
> > + memcpy(&scmd->sg_table, &ses->sg_table, sizeof(scmd->sg_table));
> > scmd->resid = ses->resid;
> > scmd->result = ses->result;
> > }
> > diff --git a/include/scsi/scsi_eh.h b/include/scsi/scsi_eh.h
> > index d21b891..d43dc83 100644
> > --- a/include/scsi/scsi_eh.h
> > +++ b/include/scsi/scsi_eh.h
> > @@ -75,6 +75,7 @@ struct scsi_eh_save {
> >
> > void *buffer;
> > unsigned bufflen;
> > + struct sg_table sg_table;
> > unsigned short use_sg;
> > int resid;
> >
> >
> Ok this is not in Linus tree is it? Hence I did not have that failure.
Yes it is, it's in current -git! James, comments on the patch? Will you
push it or shall I?
--
Jens Axboe
On Tue, 2008-01-29 at 21:03 +0100, Jens Axboe wrote:
> On Tue, Jan 29 2008, Boaz Harrosh wrote:
> > On Tue, Jan 29 2008 at 21:45 +0200, Jens Axboe <[email protected]> wrote:
> > > On Tue, Jan 29 2008, Jens Axboe wrote:
> > >> On Tue, Jan 29 2008, James Bottomley wrote:
> > >>> On Tue, 2008-01-29 at 11:10 -0800, Matthew Dharm wrote:
> > >>>> On Tue, Jan 29, 2008 at 07:39:11PM +0100, Jens Axboe wrote:
> > >>>>> On Tue, Jan 29 2008, Jens Axboe wrote:
> > >>>>>> On Tue, Jan 29 2008, Oliver Neukum wrote:
> > >>>>>>> Am Dienstag, 29. Januar 2008 15:11:08 schrieb Jens Axboe:
> > >>>>>>>> On Tue, Jan 29 2008, Boaz Harrosh wrote:
> > >>>>>>>>> On Tue, Jan 29 2008 at 15:54 +0200, Jens Axboe <[email protected]> wrote:
> > >>>>>>>>>> On Tue, Jan 29 2008, Boaz Harrosh wrote:
> > >>>>>>>>>>> Greg KH wrote:
> > >>>>>>>
> > >>>>>>>>>> No difference, still just a lot of resets.
> > >>>>>>>>>>
> > >>>>>>>>> Where you able to figure out which usb storage transport is used?
> > >>>>>>>>>
> > >>>>>>>>> in drivers/usb/storage/usb.c you have get_protocol() and get_transport()
> > >>>>>>>>> functions. I'm not sure if these get stored in sysfs perhaps. This will
> > >>>>>>>>> pinpoint better where to look. Let me research a bit.
> > >>>>>>>> Did the quick'n easy and dumped it. Protocol is 'Transparent SCSI' and
> > >>>>>>>> transport is 'Bulk'
> > >>>>>>> You can recompile your kernel with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG
> > >>>>>>> That should tell the reason for the resets.
> > >>>>>> Sure, I'll do that. Will post the results tonight.
> > >>>>> OK, fresh boot with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG. Plugged
> > >>>>> in the device, waited 10 seconds or so and pulled it out. These are the
> > >>>>> messages.
> > >>>>>
> > >>>>> It all looks good until the MODE_SENSE command, where it only transfers
> > >>>>> 4 of 192 bytes.
> > >>>> No, that's not the problem. This is the problem:
> > >>>>
> > >>>>> usb-storage: *** thread awakened.
> > >>>>> usb-storage: Command TEST_UNIT_READY (6 bytes)
> > >>>>> usb-storage: 00 00 00 00 00 00
> > >>>>> usb-storage: Bulk Command S 0x43425355 T 0xd L 0 F 0 Trg 0 LUN 1 CL 6
> > >>>>> usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
> > >>>>> usb-storage: Status code 0; transferred 31/31
> > >>>>> usb-storage: -- transfer complete
> > >>>>> usb-storage: Bulk command transfer result=0
> > >>>>> usb-storage: Attempting to get CSW...
> > >>>>> usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
> > >>>>> usb-storage: Status code 0; transferred 13/13
> > >>>>> usb-storage: -- transfer complete
> > >>>>> usb-storage: Bulk status result = 0
> > >>>>> usb-storage: Bulk Status S 0x53425355 T 0xd R 0 Stat 0x1
> > >>>>> usb-storage: -- transport indicates command failure
> > >>>>> usb-storage: Issuing auto-REQUEST_SENSE
> > >>>>> usb-storage: Bulk Command S 0x43425355 T 0xe L 18 F 128 Trg 0 LUN 1 CL 6
> > >>>>> usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
> > >>>>> usb-storage: Status code 0; transferred 31/31
> > >>>>> usb-storage: -- transfer complete
> > >>>>> usb-storage: Bulk command transfer result=0
> > >>>>> usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
> > >>>>> usb-storage: usb_sg_init returned -22
> > >>>>> usb-storage: Bulk data transfer result 0x4
> > >>>>> usb-storage: -- auto-sense failure
> > >>>>> usb-storage: storage_pre_reset
> > >>>>> ehci_hcd 0000:00:1d.7: port 1 high speed
> > >>>>> ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
> > >>>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> > >>>>> ehci_hcd 0000:00:1d.7: port 1 high speed
> > >>>>> ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
> > >>>>> usb-storage: storage_post_reset
> > >>>>> usb-storage: usb_reset_composite_device returns 0
> > >>>>> usb-storage: scsi cmd done, result=0x70000
> > >>>>> usb-storage: *** thread sleeping.
> > >>>> For some reason, usb_sg_init is boned during auto-sense.
> > >>> OK, that's implicating the scsi_eh_prep_cmnd() in the auto sense
> > >>> code ... that was also an update in 2.6.24
> > >> yeah, already found the bug - it's assuming ->request_buffer holds the
> > >> sglist, oops. Preparing a fix.
> > >
> > > ok here goes, this saves and restores the sg table correctly. it also
> > > fixes the usb bug for me.
> > >
> > > diff --git a/drivers/scsi/scsi_error.c b/drivers/scsi/scsi_error.c
> > > index 547e85a..12770ef 100644
> > > --- a/drivers/scsi/scsi_error.c
> > > +++ b/drivers/scsi/scsi_error.c
> > > @@ -622,13 +622,15 @@ void scsi_eh_prep_cmnd(struct scsi_cmnd *scmd, struct scsi_eh_save *ses,
> > > ses->use_sg = scmd->use_sg;
> > > ses->resid = scmd->resid;
> > > ses->result = scmd->result;
> > > + memcpy(&ses->sense_sgl, &scmd->sg_table, sizeof(ses->sense_sgl));
> > >
> > > if (sense_bytes) {
> > > scmd->request_bufflen = min_t(unsigned,
> > > SCSI_SENSE_BUFFERSIZE, sense_bytes);
> > > sg_init_one(&ses->sense_sgl, scmd->sense_buffer,
> > > scmd->request_bufflen);
> > > - scmd->request_buffer = &ses->sense_sgl;
> > > + scmd->sg_table.sgl = &ses->sense_sgl;
> > > + scmd->sg_table.nents = scmd->sg_table.orig_nents = 1;
> > > scmd->sc_data_direction = DMA_FROM_DEVICE;
> > > scmd->use_sg = 1;
> > > memset(scmd->cmnd, 0, sizeof(scmd->cmnd));
> > > @@ -679,6 +681,7 @@ void scsi_eh_restore_cmnd(struct scsi_cmnd* scmd, struct scsi_eh_save *ses)
> > > scmd->request_bufflen = ses->bufflen;
> > > scmd->request_buffer = ses->buffer;
> > > scmd->use_sg = ses->use_sg;
> > > + memcpy(&scmd->sg_table, &ses->sg_table, sizeof(scmd->sg_table));
> > > scmd->resid = ses->resid;
> > > scmd->result = ses->result;
> > > }
> > > diff --git a/include/scsi/scsi_eh.h b/include/scsi/scsi_eh.h
> > > index d21b891..d43dc83 100644
> > > --- a/include/scsi/scsi_eh.h
> > > +++ b/include/scsi/scsi_eh.h
> > > @@ -75,6 +75,7 @@ struct scsi_eh_save {
> > >
> > > void *buffer;
> > > unsigned bufflen;
> > > + struct sg_table sg_table;
> > > unsigned short use_sg;
> > > int resid;
> > >
> > >
> > Ok this is not in Linus tree is it? Hence I did not have that failure.
>
> Yes it is, it's in current -git! James, comments on the patch? Will you
> push it or shall I?
I will ... but it will cause an explosion in the bidirectional tree
again. I think the bidi updates also fix this. However, give me time
to rebase and verify.
James
On Tue, Jan 29 2008, James Bottomley wrote:
> On Tue, 2008-01-29 at 21:03 +0100, Jens Axboe wrote:
> > On Tue, Jan 29 2008, Boaz Harrosh wrote:
> > > On Tue, Jan 29 2008 at 21:45 +0200, Jens Axboe <[email protected]> wrote:
> > > > On Tue, Jan 29 2008, Jens Axboe wrote:
> > > >> On Tue, Jan 29 2008, James Bottomley wrote:
> > > >>> On Tue, 2008-01-29 at 11:10 -0800, Matthew Dharm wrote:
> > > >>>> On Tue, Jan 29, 2008 at 07:39:11PM +0100, Jens Axboe wrote:
> > > >>>>> On Tue, Jan 29 2008, Jens Axboe wrote:
> > > >>>>>> On Tue, Jan 29 2008, Oliver Neukum wrote:
> > > >>>>>>> Am Dienstag, 29. Januar 2008 15:11:08 schrieb Jens Axboe:
> > > >>>>>>>> On Tue, Jan 29 2008, Boaz Harrosh wrote:
> > > >>>>>>>>> On Tue, Jan 29 2008 at 15:54 +0200, Jens Axboe <[email protected]> wrote:
> > > >>>>>>>>>> On Tue, Jan 29 2008, Boaz Harrosh wrote:
> > > >>>>>>>>>>> Greg KH wrote:
> > > >>>>>>>
> > > >>>>>>>>>> No difference, still just a lot of resets.
> > > >>>>>>>>>>
> > > >>>>>>>>> Where you able to figure out which usb storage transport is used?
> > > >>>>>>>>>
> > > >>>>>>>>> in drivers/usb/storage/usb.c you have get_protocol() and get_transport()
> > > >>>>>>>>> functions. I'm not sure if these get stored in sysfs perhaps. This will
> > > >>>>>>>>> pinpoint better where to look. Let me research a bit.
> > > >>>>>>>> Did the quick'n easy and dumped it. Protocol is 'Transparent SCSI' and
> > > >>>>>>>> transport is 'Bulk'
> > > >>>>>>> You can recompile your kernel with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG
> > > >>>>>>> That should tell the reason for the resets.
> > > >>>>>> Sure, I'll do that. Will post the results tonight.
> > > >>>>> OK, fresh boot with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG. Plugged
> > > >>>>> in the device, waited 10 seconds or so and pulled it out. These are the
> > > >>>>> messages.
> > > >>>>>
> > > >>>>> It all looks good until the MODE_SENSE command, where it only transfers
> > > >>>>> 4 of 192 bytes.
> > > >>>> No, that's not the problem. This is the problem:
> > > >>>>
> > > >>>>> usb-storage: *** thread awakened.
> > > >>>>> usb-storage: Command TEST_UNIT_READY (6 bytes)
> > > >>>>> usb-storage: 00 00 00 00 00 00
> > > >>>>> usb-storage: Bulk Command S 0x43425355 T 0xd L 0 F 0 Trg 0 LUN 1 CL 6
> > > >>>>> usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
> > > >>>>> usb-storage: Status code 0; transferred 31/31
> > > >>>>> usb-storage: -- transfer complete
> > > >>>>> usb-storage: Bulk command transfer result=0
> > > >>>>> usb-storage: Attempting to get CSW...
> > > >>>>> usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
> > > >>>>> usb-storage: Status code 0; transferred 13/13
> > > >>>>> usb-storage: -- transfer complete
> > > >>>>> usb-storage: Bulk status result = 0
> > > >>>>> usb-storage: Bulk Status S 0x53425355 T 0xd R 0 Stat 0x1
> > > >>>>> usb-storage: -- transport indicates command failure
> > > >>>>> usb-storage: Issuing auto-REQUEST_SENSE
> > > >>>>> usb-storage: Bulk Command S 0x43425355 T 0xe L 18 F 128 Trg 0 LUN 1 CL 6
> > > >>>>> usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
> > > >>>>> usb-storage: Status code 0; transferred 31/31
> > > >>>>> usb-storage: -- transfer complete
> > > >>>>> usb-storage: Bulk command transfer result=0
> > > >>>>> usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
> > > >>>>> usb-storage: usb_sg_init returned -22
> > > >>>>> usb-storage: Bulk data transfer result 0x4
> > > >>>>> usb-storage: -- auto-sense failure
> > > >>>>> usb-storage: storage_pre_reset
> > > >>>>> ehci_hcd 0000:00:1d.7: port 1 high speed
> > > >>>>> ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
> > > >>>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2
> > > >>>>> ehci_hcd 0000:00:1d.7: port 1 high speed
> > > >>>>> ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
> > > >>>>> usb-storage: storage_post_reset
> > > >>>>> usb-storage: usb_reset_composite_device returns 0
> > > >>>>> usb-storage: scsi cmd done, result=0x70000
> > > >>>>> usb-storage: *** thread sleeping.
> > > >>>> For some reason, usb_sg_init is boned during auto-sense.
> > > >>> OK, that's implicating the scsi_eh_prep_cmnd() in the auto sense
> > > >>> code ... that was also an update in 2.6.24
> > > >> yeah, already found the bug - it's assuming ->request_buffer holds the
> > > >> sglist, oops. Preparing a fix.
> > > >
> > > > ok here goes, this saves and restores the sg table correctly. it also
> > > > fixes the usb bug for me.
> > > >
> > > > diff --git a/drivers/scsi/scsi_error.c b/drivers/scsi/scsi_error.c
> > > > index 547e85a..12770ef 100644
> > > > --- a/drivers/scsi/scsi_error.c
> > > > +++ b/drivers/scsi/scsi_error.c
> > > > @@ -622,13 +622,15 @@ void scsi_eh_prep_cmnd(struct scsi_cmnd *scmd, struct scsi_eh_save *ses,
> > > > ses->use_sg = scmd->use_sg;
> > > > ses->resid = scmd->resid;
> > > > ses->result = scmd->result;
> > > > + memcpy(&ses->sense_sgl, &scmd->sg_table, sizeof(ses->sense_sgl));
> > > >
> > > > if (sense_bytes) {
> > > > scmd->request_bufflen = min_t(unsigned,
> > > > SCSI_SENSE_BUFFERSIZE, sense_bytes);
> > > > sg_init_one(&ses->sense_sgl, scmd->sense_buffer,
> > > > scmd->request_bufflen);
> > > > - scmd->request_buffer = &ses->sense_sgl;
> > > > + scmd->sg_table.sgl = &ses->sense_sgl;
> > > > + scmd->sg_table.nents = scmd->sg_table.orig_nents = 1;
> > > > scmd->sc_data_direction = DMA_FROM_DEVICE;
> > > > scmd->use_sg = 1;
> > > > memset(scmd->cmnd, 0, sizeof(scmd->cmnd));
> > > > @@ -679,6 +681,7 @@ void scsi_eh_restore_cmnd(struct scsi_cmnd* scmd, struct scsi_eh_save *ses)
> > > > scmd->request_bufflen = ses->bufflen;
> > > > scmd->request_buffer = ses->buffer;
> > > > scmd->use_sg = ses->use_sg;
> > > > + memcpy(&scmd->sg_table, &ses->sg_table, sizeof(scmd->sg_table));
> > > > scmd->resid = ses->resid;
> > > > scmd->result = ses->result;
> > > > }
> > > > diff --git a/include/scsi/scsi_eh.h b/include/scsi/scsi_eh.h
> > > > index d21b891..d43dc83 100644
> > > > --- a/include/scsi/scsi_eh.h
> > > > +++ b/include/scsi/scsi_eh.h
> > > > @@ -75,6 +75,7 @@ struct scsi_eh_save {
> > > >
> > > > void *buffer;
> > > > unsigned bufflen;
> > > > + struct sg_table sg_table;
> > > > unsigned short use_sg;
> > > > int resid;
> > > >
> > > >
> > > Ok this is not in Linus tree is it? Hence I did not have that failure.
> >
> > Yes it is, it's in current -git! James, comments on the patch? Will you
> > push it or shall I?
>
> I will ... but it will cause an explosion in the bidirectional tree
> again. I think the bidi updates also fix this. However, give me time
> to rebase and verify.
OK thanks, just wanted to make sure that we didn't both expect each
other to handle it :-)
--
Jens Axboe
>>
> Ok this is not in Linus tree is it? Hence I did not have that failure.
>
> Boaz
>
>
actually James bidi tree has a fix for this in the scsi_data_buffer patch.
what you sent is not enough there are other places. look at this patch I
sent to the list.
http://www.spinics.net/lists/linux-scsi/msg21938.html
Could we take the 2 SG patches and submit them through the scsi
bidi tree? It is much more natural to have them in one tree as one
patchset then try coordinate with git-merge. Actually if you look at it,
the biggest change is to SCSI. So I think it is more natural this way
Boaz
On Tue, Jan 29 2008, Boaz Harrosh wrote:
> >>
> > Ok this is not in Linus tree is it? Hence I did not have that failure.
> >
> > Boaz
> >
> >
>
> actually James bidi tree has a fix for this in the scsi_data_buffer patch.
>
> what you sent is not enough there are other places. look at this patch I
> sent to the list.
>
> http://www.spinics.net/lists/linux-scsi/msg21938.html
Hard to compare, since its on different bases.
> Could we take the 2 SG patches and submit them through the scsi
> bidi tree? It is much more natural to have them in one tree as one
> patchset then try coordinate with git-merge. Actually if you look at it,
> the biggest change is to SCSI. So I think it is more natural this way
What 2 sg patches do you mean?
--
Jens Axboe
On Tue, 2008-01-29 at 21:06 +0100, Jens Axboe wrote:
> > I will ... but it will cause an explosion in the bidirectional tree
> > again. I think the bidi updates also fix this. However, give me time
> > to rebase and verify.
>
> OK thanks, just wanted to make sure that we didn't both expect each
> other to handle it :-)
Yes, confirm that; I think this is already fixed in scsi-misc-2.6.
Could you pull from
master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6.git
and verify with your device?
Thanks,
James
On Tue, Jan 29 2008 at 22:13 +0200, Jens Axboe <[email protected]> wrote:
> On Tue, Jan 29 2008, Boaz Harrosh wrote:
>>> Ok this is not in Linus tree is it? Hence I did not have that failure.
>>>
>>> Boaz
>>>
>>>
>> actually James bidi tree has a fix for this in the scsi_data_buffer patch.
>>
>> what you sent is not enough there are other places. look at this patch I
>> sent to the list.
>>
>> http://www.spinics.net/lists/linux-scsi/msg21938.html
>
> Hard to compare, since its on different bases.
Yes in this patchset I have taken your sg branch at the time, and
rebased it ontop of scsi_data_buffer patch. Because I felt that
it is more natural for this patch to come after the scsi total
cleanup that is scsi_data_buffer. Then the extraction to sg_table
is simple and trivial.
What I meant to point out with this patch is that all the exact same
places that are touched there should be fixed when moving to sg_table.
Look at it. It is a revised version of your patch.
>
>> Could we take the 2 SG patches and submit them through the scsi
>> bidi tree? It is much more natural to have them in one tree as one
>> patchset then try coordinate with git-merge. Actually if you look at it,
>> the biggest change is to SCSI. So I think it is more natural this way
>
> What 2 sg patches do you mean?
>
I mean the patches that where in sg branch of the linux-block tree, But
I see that it is now to late, and that they are in Linus already
James the most simple is to submit the scsi_data_buff patch that fixes
all these places. If not do you want that I send in fixes?
Boaz
On Tue, Jan 29 2008 at 22:24 +0200, James Bottomley <[email protected]> wrote:
> On Tue, 2008-01-29 at 21:06 +0100, Jens Axboe wrote:
>>> I will ... but it will cause an explosion in the bidirectional tree
>>> again. I think the bidi updates also fix this. However, give me time
>>> to rebase and verify.
>> OK thanks, just wanted to make sure that we didn't both expect each
>> other to handle it :-)
>
> Yes, confirm that; I think this is already fixed in scsi-misc-2.6.
> Could you pull from
>
> master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6.git
>
> and verify with your device?
>
> Thanks,
>
> James
>
>
I still don't see these changes, I wanted to check, make sure...
Are there mirrors on the way to here?
James I would like to remind you that one small piece is missing
from the bidi tree, as I saw it from here, it's the few patches from
scsi-pending. Mainly arm will break which is a grate loss.
I'm going home now, I'll review all the patches tomorrow and compare
to what I have, to make sure nothing was forgotten. What a waste of a day
I pulled from Linus this morning apparently minutes before the merge, and
chased a none existent bug in my tree. Sigh
Bye
Boaz
On Tue, 29 Jan 2008, Jens Axboe wrote:
> On Tue, Jan 29 2008, Jens Axboe wrote:
> > On Tue, Jan 29 2008, James Bottomley wrote:
> > > On Tue, 2008-01-29 at 11:10 -0800, Matthew Dharm wrote:
> > > > For some reason, usb_sg_init is boned during auto-sense.
> > >
> > > OK, that's implicating the scsi_eh_prep_cmnd() in the auto sense
> > > code ... that was also an update in 2.6.24
> >
> > yeah, already found the bug - it's assuming ->request_buffer holds the
> > sglist, oops. Preparing a fix.
>
> ok here goes, this saves and restores the sg table correctly. it also
> fixes the usb bug for me.
I can confirm this patch fixes the errors I was seeing with current
linux-2.6.git for the USB memory card readers in a Dell TFT connected to a PS3.
> diff --git a/drivers/scsi/scsi_error.c b/drivers/scsi/scsi_error.c
> index 547e85a..12770ef 100644
> --- a/drivers/scsi/scsi_error.c
> +++ b/drivers/scsi/scsi_error.c
> @@ -622,13 +622,15 @@ void scsi_eh_prep_cmnd(struct scsi_cmnd *scmd, struct scsi_eh_save *ses,
> ses->use_sg = scmd->use_sg;
> ses->resid = scmd->resid;
> ses->result = scmd->result;
> + memcpy(&ses->sense_sgl, &scmd->sg_table, sizeof(ses->sense_sgl));
>
> if (sense_bytes) {
> scmd->request_bufflen = min_t(unsigned,
> SCSI_SENSE_BUFFERSIZE, sense_bytes);
> sg_init_one(&ses->sense_sgl, scmd->sense_buffer,
> scmd->request_bufflen);
> - scmd->request_buffer = &ses->sense_sgl;
> + scmd->sg_table.sgl = &ses->sense_sgl;
> + scmd->sg_table.nents = scmd->sg_table.orig_nents = 1;
> scmd->sc_data_direction = DMA_FROM_DEVICE;
> scmd->use_sg = 1;
> memset(scmd->cmnd, 0, sizeof(scmd->cmnd));
> @@ -679,6 +681,7 @@ void scsi_eh_restore_cmnd(struct scsi_cmnd* scmd, struct scsi_eh_save *ses)
> scmd->request_bufflen = ses->bufflen;
> scmd->request_buffer = ses->buffer;
> scmd->use_sg = ses->use_sg;
> + memcpy(&scmd->sg_table, &ses->sg_table, sizeof(scmd->sg_table));
> scmd->resid = ses->resid;
> scmd->result = ses->result;
> }
> diff --git a/include/scsi/scsi_eh.h b/include/scsi/scsi_eh.h
> index d21b891..d43dc83 100644
> --- a/include/scsi/scsi_eh.h
> +++ b/include/scsi/scsi_eh.h
> @@ -75,6 +75,7 @@ struct scsi_eh_save {
>
> void *buffer;
> unsigned bufflen;
> + struct sg_table sg_table;
> unsigned short use_sg;
> int resid;
>
With kind regards,
Geert Uytterhoeven
Software Architect
Sony Network and Software Technology Center Europe
The Corporate Village · Da Vincilaan 7-D1 · B-1935 Zaventem · Belgium
Phone: +32 (0)2 700 8453
Fax: +32 (0)2 700 8622
E-mail: [email protected]
Internet: http://www.sony-europe.com/
Sony Network and Software Technology Center Europe
A division of Sony Service Centre (Europe) N.V.
Registered office: Technologielaan 7 · B-1840 Londerzeel · Belgium
VAT BE 0413.825.160 · RPR Brussels
Fortis Bank Zaventem · Swift GEBABEBB08A · IBAN BE39001382358619
On Wed, Jan 30 2008, Geert Uytterhoeven wrote:
> On Tue, 29 Jan 2008, Jens Axboe wrote:
> > On Tue, Jan 29 2008, Jens Axboe wrote:
> > > On Tue, Jan 29 2008, James Bottomley wrote:
> > > > On Tue, 2008-01-29 at 11:10 -0800, Matthew Dharm wrote:
> > > > > For some reason, usb_sg_init is boned during auto-sense.
> > > >
> > > > OK, that's implicating the scsi_eh_prep_cmnd() in the auto sense
> > > > code ... that was also an update in 2.6.24
> > >
> > > yeah, already found the bug - it's assuming ->request_buffer holds the
> > > sglist, oops. Preparing a fix.
> >
> > ok here goes, this saves and restores the sg table correctly. it also
> > fixes the usb bug for me.
>
> I can confirm this patch fixes the errors I was seeing with current
> linux-2.6.git for the USB memory card readers in a Dell TFT connected
> to a PS3.
James, we need a fix for this pushed asap. So either we should merge the
below now, or push the bidi patchset that also fixes this. It all
depends on when you want to merge the bidi patches...
> > diff --git a/drivers/scsi/scsi_error.c b/drivers/scsi/scsi_error.c
> > index 547e85a..12770ef 100644
> > --- a/drivers/scsi/scsi_error.c
> > +++ b/drivers/scsi/scsi_error.c
> > @@ -622,13 +622,15 @@ void scsi_eh_prep_cmnd(struct scsi_cmnd *scmd, struct scsi_eh_save *ses,
> > ses->use_sg = scmd->use_sg;
> > ses->resid = scmd->resid;
> > ses->result = scmd->result;
> > + memcpy(&ses->sense_sgl, &scmd->sg_table, sizeof(ses->sense_sgl));
> >
> > if (sense_bytes) {
> > scmd->request_bufflen = min_t(unsigned,
> > SCSI_SENSE_BUFFERSIZE, sense_bytes);
> > sg_init_one(&ses->sense_sgl, scmd->sense_buffer,
> > scmd->request_bufflen);
> > - scmd->request_buffer = &ses->sense_sgl;
> > + scmd->sg_table.sgl = &ses->sense_sgl;
> > + scmd->sg_table.nents = scmd->sg_table.orig_nents = 1;
> > scmd->sc_data_direction = DMA_FROM_DEVICE;
> > scmd->use_sg = 1;
> > memset(scmd->cmnd, 0, sizeof(scmd->cmnd));
> > @@ -679,6 +681,7 @@ void scsi_eh_restore_cmnd(struct scsi_cmnd* scmd, struct scsi_eh_save *ses)
> > scmd->request_bufflen = ses->bufflen;
> > scmd->request_buffer = ses->buffer;
> > scmd->use_sg = ses->use_sg;
> > + memcpy(&scmd->sg_table, &ses->sg_table, sizeof(scmd->sg_table));
> > scmd->resid = ses->resid;
> > scmd->result = ses->result;
> > }
> > diff --git a/include/scsi/scsi_eh.h b/include/scsi/scsi_eh.h
> > index d21b891..d43dc83 100644
> > --- a/include/scsi/scsi_eh.h
> > +++ b/include/scsi/scsi_eh.h
> > @@ -75,6 +75,7 @@ struct scsi_eh_save {
> >
> > void *buffer;
> > unsigned bufflen;
> > + struct sg_table sg_table;
> > unsigned short use_sg;
> > int resid;
> >
--
Jens Axboe
On Wed, 2008-01-30 at 11:38 +0100, Jens Axboe wrote:
> On Wed, Jan 30 2008, Geert Uytterhoeven wrote:
> > On Tue, 29 Jan 2008, Jens Axboe wrote:
> > > On Tue, Jan 29 2008, Jens Axboe wrote:
> > > > On Tue, Jan 29 2008, James Bottomley wrote:
> > > > > On Tue, 2008-01-29 at 11:10 -0800, Matthew Dharm wrote:
> > > > > > For some reason, usb_sg_init is boned during auto-sense.
> > > > >
> > > > > OK, that's implicating the scsi_eh_prep_cmnd() in the auto sense
> > > > > code ... that was also an update in 2.6.24
> > > >
> > > > yeah, already found the bug - it's assuming ->request_buffer holds the
> > > > sglist, oops. Preparing a fix.
> > >
> > > ok here goes, this saves and restores the sg table correctly. it also
> > > fixes the usb bug for me.
> >
> > I can confirm this patch fixes the errors I was seeing with current
> > linux-2.6.git for the USB memory card readers in a Dell TFT connected
> > to a PS3.
>
> James, we need a fix for this pushed asap. So either we should merge the
> below now, or push the bidi patchset that also fixes this. It all
> depends on when you want to merge the bidi patches...
The SCSI patch set (including the bidirectional pieces) is waiting in
scsi-misc ... just for forms sake, could you confirm that it actually
fixes the problem and I'll push it.
James
On Wed, Jan 30 2008, James Bottomley wrote:
> On Wed, 2008-01-30 at 11:38 +0100, Jens Axboe wrote:
> > On Wed, Jan 30 2008, Geert Uytterhoeven wrote:
> > > On Tue, 29 Jan 2008, Jens Axboe wrote:
> > > > On Tue, Jan 29 2008, Jens Axboe wrote:
> > > > > On Tue, Jan 29 2008, James Bottomley wrote:
> > > > > > On Tue, 2008-01-29 at 11:10 -0800, Matthew Dharm wrote:
> > > > > > > For some reason, usb_sg_init is boned during auto-sense.
> > > > > >
> > > > > > OK, that's implicating the scsi_eh_prep_cmnd() in the auto sense
> > > > > > code ... that was also an update in 2.6.24
> > > > >
> > > > > yeah, already found the bug - it's assuming ->request_buffer holds the
> > > > > sglist, oops. Preparing a fix.
> > > >
> > > > ok here goes, this saves and restores the sg table correctly. it also
> > > > fixes the usb bug for me.
> > >
> > > I can confirm this patch fixes the errors I was seeing with current
> > > linux-2.6.git for the USB memory card readers in a Dell TFT connected
> > > to a PS3.
> >
> > James, we need a fix for this pushed asap. So either we should merge the
> > below now, or push the bidi patchset that also fixes this. It all
> > depends on when you want to merge the bidi patches...
>
> The SCSI patch set (including the bidirectional pieces) is waiting in
> scsi-misc ... just for forms sake, could you confirm that it actually
> fixes the problem and I'll push it.
Certainly, I'll give it a spin tonight.
--
Jens Axboe
On Wed, Jan 30 2008, Jens Axboe wrote:
> On Wed, Jan 30 2008, James Bottomley wrote:
> > On Wed, 2008-01-30 at 11:38 +0100, Jens Axboe wrote:
> > > On Wed, Jan 30 2008, Geert Uytterhoeven wrote:
> > > > On Tue, 29 Jan 2008, Jens Axboe wrote:
> > > > > On Tue, Jan 29 2008, Jens Axboe wrote:
> > > > > > On Tue, Jan 29 2008, James Bottomley wrote:
> > > > > > > On Tue, 2008-01-29 at 11:10 -0800, Matthew Dharm wrote:
> > > > > > > > For some reason, usb_sg_init is boned during auto-sense.
> > > > > > >
> > > > > > > OK, that's implicating the scsi_eh_prep_cmnd() in the auto sense
> > > > > > > code ... that was also an update in 2.6.24
> > > > > >
> > > > > > yeah, already found the bug - it's assuming ->request_buffer holds the
> > > > > > sglist, oops. Preparing a fix.
> > > > >
> > > > > ok here goes, this saves and restores the sg table correctly. it also
> > > > > fixes the usb bug for me.
> > > >
> > > > I can confirm this patch fixes the errors I was seeing with current
> > > > linux-2.6.git for the USB memory card readers in a Dell TFT connected
> > > > to a PS3.
> > >
> > > James, we need a fix for this pushed asap. So either we should merge the
> > > below now, or push the bidi patchset that also fixes this. It all
> > > depends on when you want to merge the bidi patches...
> >
> > The SCSI patch set (including the bidirectional pieces) is waiting in
> > scsi-misc ... just for forms sake, could you confirm that it actually
> > fixes the problem and I'll push it.
>
> Certainly, I'll give it a spin tonight.
Confirmed, pulling your scsi-misc branch into current -git makes the
problem go away as well.
--
Jens Axboe