From: Arjan Opmeer <[email protected]>
There exist laptops with Elantech touchpads where switching to absolute mode
does not happen, although writing the configuration register succeeds
without error. Reading back the register afterwards reveils that the
absolute mode bit is not set as if masked out by the touchpad firmware.
Always read back register 0x10, make sure that for hardware version 1 the
absolute mode bit is actually set and fail otherwise. This prevents the case
where the touchpad is claimed by the Elantech driver but is nonetheless not
working.
Signed-off-by: Arjan Opmeer <[email protected]>
---
diff --git a/drivers/input/mouse/elantech.c b/drivers/input/mouse/elantech.c
index 6ab0eb1..1de6fd6 100644
--- a/drivers/input/mouse/elantech.c
+++ b/drivers/input/mouse/elantech.c
@@ -363,9 +363,14 @@ static int elantech_set_absolute_mode(struct psmouse *psmouse)
rc = -1;
break;
}
+ }
+
+ if (rc == 0) {
/*
- * Read back reg 0x10. The touchpad is probably initalising
- * and not ready until we read back the value we just wrote.
+ * Read back reg 0x10. For hardware version 1 we must make
+ * sure the absolute mode bit is set. For hardware version 2
+ * the touchpad is probably initalising and not ready until
+ * we read back the value we just wrote.
*/
do {
rc = elantech_read_reg(psmouse, 0x10, &val);
@@ -376,9 +381,17 @@ static int elantech_set_absolute_mode(struct psmouse *psmouse)
tries);
msleep(ETP_READ_BACK_DELAY);
} while (tries > 0);
- if (rc)
+
+ if (rc) {
pr_err("elantech.c: failed to read back register 0x10.\n");
- break;
+ } else {
+ if (etd->hw_version == 1 &&
+ val & ETP_R10_ABSOLUTE_MODE == 0) {
+ pr_err("elantech.c: touchpad refuses "
+ "to have absolute mode bit set\n");
+ rc = -1;
+ }
+ }
}
if (rc)
Hi Arjan,
On Thursday 19 March 2009 22:52:39 Arjan Opmeer wrote:
> From: Arjan Opmeer <[email protected]>
>
> There exist laptops with Elantech touchpads where switching to absolute
> mode does not happen, although writing the configuration register succeeds
> without error. Reading back the register afterwards reveils that the
> absolute mode bit is not set as if masked out by the touchpad firmware.
>
> Always read back register 0x10, make sure that for hardware version 1 the
> absolute mode bit is actually set and fail otherwise. This prevents the
> case where the touchpad is claimed by the Elantech driver but is
> nonetheless not working.
>
Makes sense, will apply. Although, have you tried repeating the switch or
maybe issuing full reset before trying again?
--
Dmitry
On Fri, Mar 20, 2009 at 10:46:31PM -0700, Dmitry Torokhov wrote:
> On Thursday 19 March 2009 22:52:39 Arjan Opmeer wrote:
> >
> > There exist laptops with Elantech touchpads where switching to absolute
> > mode does not happen, although writing the configuration register
> > succeeds without error. Reading back the register afterwards reveils
> > that the absolute mode bit is not set as if masked out by the touchpad
> > firmware.
> >
> > Always read back register 0x10, make sure that for hardware version 1
> > the absolute mode bit is actually set and fail otherwise. This prevents
> > the case where the touchpad is claimed by the Elantech driver but is
> > nonetheless not working.
>
> Makes sense, will apply. Although, have you tried repeating the switch or
> maybe issuing full reset before trying again?
No. I am sorry. I had this problem reported by two different users that both
kind of lost interest when I pointed out that the driver as it stands was
not able to support their laptops. Without access to the hardware and
without users willing to test I am rather stuck.
So I thought the sensible thing left to do was to put an extra check and
warning in the driver to prevent other users from falling in that trap where
their touchpad isn't working.
Arjan