From: Purshotam Kumar <[email protected]>
This patch adds support for MMC/SD controller driver for DaVinci family SoC.
This patch will work for SoC like DM6446 and DM355. SoC like DM365 and
DA830 also has same controller with small variations and could supported/added
easily by using this version of patch. It means that this version of patch
could be used for all SoC which has been derived from DaVinci family.
This patch has been generated against latest 2.6.29 mainline kernel. This patch
will not compile currently because it depends notably on the EDMA utilities and
chip/board setup, that will come at some point through the ARM tree. Please use
currently DaVinci GIT tree for EDMA utilities and chip/board setup etc.
Many thanks to David Brownell ([email protected]) for his all support.
This updated patch incorporates most of review comments given by
Pierre Ossman. Many thanks for Pierre Ossman for reviewing.
Signed-off-by: Purshotam Kumar <[email protected]>
Acked-by: David Brownell <[email protected]>
---
arch/arm/mach-davinci/include/mach/mmc.h | 25 +
drivers/mmc/host/Kconfig | 8 +
drivers/mmc/host/Makefile | 1 +
drivers/mmc/host/davinci_mmc.c | 1264 ++++++++++++++++++++++++++++++
4 files changed, 1298 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/mach-davinci/include/mach/mmc.h
create mode 100644 drivers/mmc/host/davinci_mmc.c
diff --git a/arch/arm/mach-davinci/include/mach/mmc.h b/arch/arm/mach-davinci/include/mach/mmc.h
new file mode 100644
index 0000000..8fee158
--- /dev/null
+++ b/arch/arm/mach-davinci/include/mach/mmc.h
@@ -0,0 +1,25 @@
+/*
+ * Board-specific MMC configuration
+ */
+
+#ifndef _DAVINCI_MMC_H
+#define _DAVINCI_MMC_H
+
+#include <linux/types.h>
+#include <linux/mmc/host.h>
+
+struct davinci_mmc_config {
+ /* get_cd()/get_wp() may sleep */
+ int (*get_cd)(int module);
+ int (*get_ro)(int module);
+ /* wires == 0 is equivalent to wires == 4 (4-bit parallel) */
+ u8 wires;
+
+ u32 max_freq;
+
+ /* any additional host capabilities: OR'd in to mmc->f_caps */
+ u32 caps;
+};
+void davinci_setup_mmc(int module, struct davinci_mmc_config *config);
+
+#endif
diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
index 99d4b28..311d00f 100644
--- a/drivers/mmc/host/Kconfig
+++ b/drivers/mmc/host/Kconfig
@@ -171,6 +171,14 @@ config MMC_TIFM_SD
To compile this driver as a module, choose M here: the
module will be called tifm_sd.
+config MMC_DAVINCI
+ tristate "TI DAVINCI Multimedia Card Interface support"
+ depends on ARCH_DAVINCI
+ help
+ This selects the TI DAVINCI Multimedia card Interface.
+ If you have an DAVINCI board with a Multimedia Card slot,
+ say Y or M here. If unsure, say N.
+
config MMC_SPI
tristate "MMC/SD/SDIO over SPI"
depends on SPI_MASTER && !HIGHMEM && HAS_DMA
diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
index dedec55..6bc91b1 100644
--- a/drivers/mmc/host/Makefile
+++ b/drivers/mmc/host/Makefile
@@ -20,6 +20,7 @@ obj-$(CONFIG_MMC_OMAP_HS) += omap_hsmmc.o
obj-$(CONFIG_MMC_AT91) += at91_mci.o
obj-$(CONFIG_MMC_ATMELMCI) += atmel-mci.o
obj-$(CONFIG_MMC_TIFM_SD) += tifm_sd.o
+obj-$(CONFIG_MMC_DAVINCI) += davinci_mmc.o
obj-$(CONFIG_MMC_SPI) += mmc_spi.o
ifeq ($(CONFIG_OF),y)
obj-$(CONFIG_MMC_SPI) += of_mmc_spi.o
diff --git a/drivers/mmc/host/davinci_mmc.c b/drivers/mmc/host/davinci_mmc.c
new file mode 100644
index 0000000..eac74ff
--- /dev/null
+++ b/drivers/mmc/host/davinci_mmc.c
@@ -0,0 +1,1264 @@
+/*
+ * davinci_mmc.c - TI DaVinci MMC/SD/SDIO driver
+ *
+ * Copyright (C) 2006 Texas Instruments.
+ * Original author: Purushotam Kumar
+ * Copyright (C) 2009 David Brownell
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/module.h>
+#include <linux/ioport.h>
+#include <linux/platform_device.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/mmc/host.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/mmc/mmc.h>
+
+#include <mach/mmc.h>
+#include <mach/edma.h>
+
+/*
+ * Register Definitions
+ */
+#define DAVINCI_MMCCTL 0x00 /* Control Register */
+#define DAVINCI_MMCCLK 0x04 /* Memory Clock Control Register */
+#define DAVINCI_MMCST0 0x08 /* Status Register 0 */
+#define DAVINCI_MMCST1 0x0C /* Status Register 1 */
+#define DAVINCI_MMCIM 0x10 /* Interrupt Mask Register */
+#define DAVINCI_MMCTOR 0x14 /* Response Time-Out Register */
+#define DAVINCI_MMCTOD 0x18 /* Data Read Time-Out Register */
+#define DAVINCI_MMCBLEN 0x1C /* Block Length Register */
+#define DAVINCI_MMCNBLK 0x20 /* Number of Blocks Register */
+#define DAVINCI_MMCNBLC 0x24 /* Number of Blocks Counter Register */
+#define DAVINCI_MMCDRR 0x28 /* Data Receive Register */
+#define DAVINCI_MMCDXR 0x2C /* Data Transmit Register */
+#define DAVINCI_MMCCMD 0x30 /* Command Register */
+#define DAVINCI_MMCARGHL 0x34 /* Argument Register */
+#define DAVINCI_MMCRSP01 0x38 /* Response Register 0 and 1 */
+#define DAVINCI_MMCRSP23 0x3C /* Response Register 0 and 1 */
+#define DAVINCI_MMCRSP45 0x40 /* Response Register 0 and 1 */
+#define DAVINCI_MMCRSP67 0x44 /* Response Register 0 and 1 */
+#define DAVINCI_MMCDRSP 0x48 /* Data Response Register */
+#define DAVINCI_MMCETOK 0x4C
+#define DAVINCI_MMCCIDX 0x50 /* Command Index Register */
+#define DAVINCI_MMCCKC 0x54
+#define DAVINCI_MMCTORC 0x58
+#define DAVINCI_MMCTODC 0x5C
+#define DAVINCI_MMCBLNC 0x60
+#define DAVINCI_SDIOCTL 0x64
+#define DAVINCI_SDIOST0 0x68
+#define DAVINCI_SDIOEN 0x6C
+#define DAVINCI_SDIOST 0x70
+#define DAVINCI_MMCFIFOCTL 0x74 /* FIFO Control Register */
+
+/* DAVINCI_MMCCTL definitions */
+#define MMCCTL_DATRST (1 << 0)
+#define MMCCTL_CMDRST (1 << 1)
+#define MMCCTL_WIDTH_4_BIT (1 << 2)
+#define MMCCTL_DATEG_DISABLED (0 << 6)
+#define MMCCTL_DATEG_RISING (1 << 6)
+#define MMCCTL_DATEG_FALLING (2 << 6)
+#define MMCCTL_DATEG_BOTH (3 << 6)
+#define MMCCTL_PERMDR_LE (0 << 9)
+#define MMCCTL_PERMDR_BE (1 << 9)
+#define MMCCTL_PERMDX_LE (0 << 10)
+#define MMCCTL_PERMDX_BE (1 << 10)
+
+/* DAVINCI_MMCCLK definitions */
+#define MMCCLK_CLKEN (1 << 8)
+#define MMCCLK_CLKRT_MASK (0xFF << 0)
+
+/* IRQ bit definitions, for DAVINCI_MMCST0 and DAVINCI_MMCIM */
+#define MMCST0_DATDNE BIT(0) /* data done */
+#define MMCST0_BSYDNE BIT(1) /* busy done */
+#define MMCST0_RSPDNE BIT(2) /* command done */
+#define MMCST0_TOUTRD BIT(3) /* data read timeout */
+#define MMCST0_TOUTRS BIT(4) /* command response timeout */
+#define MMCST0_CRCWR BIT(5) /* data write CRC error */
+#define MMCST0_CRCRD BIT(6) /* data read CRC error */
+#define MMCST0_CRCRS BIT(7) /* command response CRC error */
+#define MMCST0_DXRDY BIT(9) /* data transmit ready (fifo empty) */
+#define MMCST0_DRRDY BIT(10) /* data receive ready (data in fifo)*/
+#define MMCST0_DATED BIT(11) /* DAT3 edge detect */
+#define MMCST0_TRNDNE BIT(12) /* transfer done */
+
+/* DAVINCI_MMCST1 definitions */
+#define MMCST1_BUSY (1 << 0)
+
+/* DAVINCI_MMCCMD definitions */
+#define MMCCMD_CMD_MASK (0x3F << 0)
+#define MMCCMD_PPLEN (1 << 7)
+#define MMCCMD_BSYEXP (1 << 8)
+#define MMCCMD_RSPFMT_MASK (3 << 9)
+#define MMCCMD_RSPFMT_NONE (0 << 9)
+#define MMCCMD_RSPFMT_R1456 (1 << 9)
+#define MMCCMD_RSPFMT_R2 (2 << 9)
+#define MMCCMD_RSPFMT_R3 (3 << 9)
+#define MMCCMD_DTRW (1 << 11)
+#define MMCCMD_STRMTP (1 << 12)
+#define MMCCMD_WDATX (1 << 13)
+#define MMCCMD_INITCK (1 << 14)
+#define MMCCMD_DCLR (1 << 15)
+#define MMCCMD_DMATRIG (1 << 16)
+
+/* DAVINCI_MMCFIFOCTL definitions */
+#define MMCFIFOCTL_FIFORST (1 << 0)
+#define MMCFIFOCTL_FIFODIR_WR (1 << 1)
+#define MMCFIFOCTL_FIFODIR_RD (0 << 1)
+#define MMCFIFOCTL_FIFOLEV (1 << 2) /* 0 = 128 bits, 1 = 256 bits */
+#define MMCFIFOCTL_ACCWD_4 (0 << 3) /* access width of 4 bytes */
+#define MMCFIFOCTL_ACCWD_3 (1 << 3) /* access width of 3 bytes */
+#define MMCFIFOCTL_ACCWD_2 (2 << 3) /* access width of 2 bytes */
+#define MMCFIFOCTL_ACCWD_1 (3 << 3) /* access width of 1 byte */
+
+
+/* MMCSD Init clock in Hz in opendrain mode */
+#define MMCSD_INIT_CLOCK 200000
+
+/*
+ * One scatterlist dma "segment" is at most MAX_CCNT rw_threshold units,
+ * and we handle up to NR_SG segments. MMC_BLOCK_BOUNCE kicks in only
+ * for drivers with max_hw_segs == 1, making the segments bigger (64KB)
+ * than the page or two that's otherwise typical. NR_SG == 16 gives at
+ * least the same throughput boost, using EDMA transfer linkage instead
+ * of spending CPU time copying pages.
+ */
+#define MAX_CCNT ((1 << 16) - 1)
+
+#define NR_SG 16
+
+#define DAVINCI_MMC_FIFO_SIZE_BYTE 32
+static unsigned rw_threshold = 32;
+static unsigned ns_in_one_cycle = 1;
+module_param(rw_threshold, uint, S_IRUGO);
+MODULE_PARM_DESC(rw_threshold,
+ "Read/Write threshold, can be 16/32. Default = 32");
+
+static unsigned __initdata use_dma = 1;
+module_param(use_dma, uint, 0);
+MODULE_PARM_DESC(use_dma, "Whether to use DMA or not. Default = 1");
+
+struct mmc_davinci_host {
+ struct mmc_command *cmd;
+ struct mmc_data *data;
+ struct mmc_host *mmc;
+ struct clk *clk;
+ unsigned int mmc_input_clk;
+ void __iomem *base;
+ struct resource *mem_res;
+ int irq;
+ unsigned char bus_mode;
+
+#define DAVINCI_MMC_DATADIR_NONE 0
+#define DAVINCI_MMC_DATADIR_READ 1
+#define DAVINCI_MMC_DATADIR_WRITE 2
+ unsigned char data_dir;
+
+ /* buffer is used during PIO of one scatterlist segment, and
+ * is updated along with buffer_bytes_left. bytes_left applies
+ * to all N blocks of the PIO transfer.
+ */
+ u8 *buffer;
+ u32 buffer_bytes_left;
+ u32 bytes_left;
+
+ u8 rxdma, txdma;
+ bool use_dma;
+ bool do_dma;
+
+ /* Scatterlist DMA uses one or more parameter RAM entries:
+ * the main one (associated with rxdma or txdma) plus zero or
+ * more links. The entries for a given transfer differ only
+ * by memory buffer (address, length) and link field.
+ */
+ struct edmacc_param tx_template;
+ struct edmacc_param rx_template;
+ unsigned n_link;
+ u8 links[NR_SG - 1];
+
+ /* For PIO we walk scatterlists one segment at a time. */
+ unsigned int sg_len;
+};
+
+
+/* PIO only */
+static void mmc_davinci_sg_to_buf(struct mmc_davinci_host *host)
+{
+ struct scatterlist *sg;
+ sg = host->data->sg;
+ host->buffer_bytes_left = sg_dma_len(sg);
+ host->buffer = sg_virt(sg);
+ if (host->buffer_bytes_left > host->bytes_left)
+ host->buffer_bytes_left = host->bytes_left;
+}
+
+static void davinci_fifo_data_trans(struct mmc_davinci_host *host,
+ unsigned int n)
+{
+ u8 *p;
+ unsigned int i;
+
+ if (host->buffer_bytes_left == 0) {
+ host->data->sg = sg_next(host->data->sg);
+ mmc_davinci_sg_to_buf(host);
+ }
+
+ p = host->buffer;
+ if (n > host->buffer_bytes_left)
+ n = host->buffer_bytes_left;
+ host->buffer_bytes_left -= n;
+ host->bytes_left -= n;
+
+ /* NOTE: we never transfer more than rw_threshold bytes
+ * to/from the fifo here; there's no I/O overlap.
+ * This also assumes that access width( i.e. ACCWD) is 4 bytes
+ */
+ if (host->data_dir == DAVINCI_MMC_DATADIR_WRITE) {
+ for (i = 0; i < (n >> 2); i++) {
+ writel(*((u32 *)p), host->base + DAVINCI_MMCDXR);
+ p = p + 4;
+ }
+ if (n & 3) {
+ iowrite8_rep(host->base + DAVINCI_MMCDXR, p, (n & 3));
+ p = p + (n & 3);
+ }
+ } else {
+ for (i = 0; i < (n >> 2); i++) {
+ *((u32 *)p) = readl(host->base + DAVINCI_MMCDRR);
+ p = p + 4;
+ }
+ if (n & 3) {
+ ioread8_rep(host->base + DAVINCI_MMCDRR, p, (n & 3));
+ p = p + (n & 3);
+ }
+ }
+ host->buffer = p;
+}
+
+static void mmc_davinci_start_command(struct mmc_davinci_host *host,
+ struct mmc_command *cmd)
+{
+ u32 cmd_reg = 0;
+ u32 im_val;
+
+ dev_dbg(mmc_dev(host->mmc), "CMD%d, arg 0x%08x%s\n",
+ cmd->opcode, cmd->arg,
+ ({ char *s;
+ switch (mmc_resp_type(cmd)) {
+ case MMC_RSP_R1:
+ s = ", R1/R5/R6/R7 response";
+ break;
+ case MMC_RSP_R1B:
+ s = ", R1b response";
+ break;
+ case MMC_RSP_R2:
+ s = ", R2 response";
+ break;
+ case MMC_RSP_R3:
+ s = ", R3/R4 response";
+ break;
+ default:
+ s = ", (R? response)";
+ break;
+ }; s; }));
+ host->cmd = cmd;
+
+ switch (mmc_resp_type(cmd)) {
+ case MMC_RSP_R1B:
+ /* There's some spec confusion about when R1B is
+ * allowed, but if the card doesn't issue a BUSY
+ * then it's harmless for us to allow it.
+ */
+ cmd_reg |= MMCCMD_BSYEXP;
+ /* FALLTHROUGH */
+ case MMC_RSP_R1: /* 48 bits, CRC */
+ cmd_reg |= MMCCMD_RSPFMT_R1456;
+ break;
+ case MMC_RSP_R2: /* 136 bits, CRC */
+ cmd_reg |= MMCCMD_RSPFMT_R2;
+ break;
+ case MMC_RSP_R3: /* 48 bits, no CRC */
+ cmd_reg |= MMCCMD_RSPFMT_R3;
+ break;
+ default:
+ cmd_reg |= MMCCMD_RSPFMT_NONE;
+ dev_dbg(mmc_dev(host->mmc), "unknown resp_type %04x\n",
+ mmc_resp_type(cmd));
+ break;
+ }
+
+ /* Set command index */
+ cmd_reg |= cmd->opcode;
+
+ /* Enable EDMA transfer triggers */
+ if (host->do_dma)
+ cmd_reg |= MMCCMD_DMATRIG;
+
+ /* Setting whether command involves data transfer or not */
+ if (cmd->data)
+ cmd_reg |= MMCCMD_WDATX;
+
+ /* Setting whether stream or block transfer */
+ if (cmd->flags & MMC_DATA_STREAM)
+ cmd_reg |= MMCCMD_STRMTP;
+
+ /* Setting whether data read or write */
+ if (host->data_dir == DAVINCI_MMC_DATADIR_WRITE)
+ cmd_reg |= MMCCMD_DTRW;
+
+ if (host->bus_mode == MMC_BUSMODE_PUSHPULL)
+ cmd_reg |= MMCCMD_PPLEN;
+
+ /* set Command timeout */
+ writel(0x1FFF, host->base + DAVINCI_MMCTOR);
+
+ /* Enable interrupt (calculate here, defer until FIFO is stuffed). */
+ im_val = MMCST0_RSPDNE | MMCST0_CRCRS | MMCST0_TOUTRS;
+ if (host->data_dir == DAVINCI_MMC_DATADIR_WRITE) {
+ im_val |= MMCST0_DATDNE | MMCST0_CRCWR;
+
+ if (!host->do_dma)
+ im_val |= MMCST0_DXRDY;
+ } else if (host->data_dir == DAVINCI_MMC_DATADIR_READ) {
+ im_val |= MMCST0_DATDNE | MMCST0_CRCRD | MMCST0_TOUTRD;
+
+ if (!host->do_dma)
+ im_val |= MMCST0_DRRDY;
+ }
+
+ /*
+ * Before non-DMA WRITE commands the controller needs priming:
+ * FIFO should be populated with 32 bytes i.e. whatever is the FIFO size
+ */
+ if (!host->do_dma && (host->data_dir == DAVINCI_MMC_DATADIR_WRITE) &&
+ ((cmd->opcode == MMC_WRITE_BLOCK) ||
+ (cmd->opcode == MMC_WRITE_MULTIPLE_BLOCK)))
+ davinci_fifo_data_trans(host, DAVINCI_MMC_FIFO_SIZE_BYTE);
+
+ writel(cmd->arg, host->base + DAVINCI_MMCARGHL);
+ writel(cmd_reg, host->base + DAVINCI_MMCCMD);
+ writel(im_val, host->base + DAVINCI_MMCIM);
+}
+
+/*----------------------------------------------------------------------*/
+
+/* DMA infrastructure */
+
+static void davinci_abort_dma(struct mmc_davinci_host *host)
+{
+ int sync_dev;
+
+ if (host->data_dir == DAVINCI_MMC_DATADIR_READ)
+ sync_dev = host->rxdma;
+ else
+ sync_dev = host->txdma;
+
+ edma_stop(sync_dev);
+ edma_clean_channel(sync_dev);
+}
+
+static void
+mmc_davinci_xfer_done(struct mmc_davinci_host *host, struct mmc_data *data);
+
+static void mmc_davinci_dma_cb(unsigned channel, u16 ch_status, void *data)
+{
+ if (DMA_COMPLETE != ch_status) {
+ struct mmc_davinci_host *host = data;
+
+ /* Currently means: DMA Event Missed, or "null" transfer
+ * request was seen. In the future, TC errors (like bad
+ * addresses) might be presented too.
+ */
+ dev_warn(mmc_dev(host->mmc), "DMA %s error\n",
+ (host->data->flags & MMC_DATA_WRITE)
+ ? "write" : "read");
+ host->data->error = -EIO;
+ mmc_davinci_xfer_done(host, host->data);
+ }
+}
+
+/* Set up tx or rx template, to be modified and updated later */
+static void __init mmc_davinci_dma_setup(struct mmc_davinci_host *host,
+ bool tx, struct edmacc_param *template)
+{
+ unsigned sync_dev;
+ const u16 acnt = 4;
+ const u16 bcnt = rw_threshold >> 2;
+ const u16 ccnt = 0;
+ u32 src_port = 0;
+ u32 dst_port = 0;
+ s16 src_bidx, dst_bidx;
+ s16 src_cidx, dst_cidx;
+
+ /*
+ * A-B Sync transfer: each DMA request is for one "frame" of
+ * rw_threshold bytes, broken into "acnt"-size chunks repeated
+ * "bcnt" times. Each segment needs "ccnt" such frames; since
+ * we tell the block layer our mmc->max_seg_size limit, we can
+ * trust (later) that it's within bounds.
+ *
+ * The FIFOs are read/written in 4-byte chunks (acnt == 4) and
+ * EDMA will optimize memory operations to use larger bursts.
+ */
+ if (tx) {
+ sync_dev = host->txdma;
+
+ /* src_prt, ccnt, and link to be set up later */
+ src_bidx = acnt;
+ src_cidx = acnt * bcnt;
+
+ dst_port = host->mem_res->start + DAVINCI_MMCDXR;
+ dst_bidx = 0;
+ dst_cidx = 0;
+ } else {
+ sync_dev = host->rxdma;
+
+ src_port = host->mem_res->start + DAVINCI_MMCDRR;
+ src_bidx = 0;
+ src_cidx = 0;
+
+ /* dst_prt, ccnt, and link to be set up later */
+ dst_bidx = acnt;
+ dst_cidx = acnt * bcnt;
+ }
+
+ /*
+ * We can't use FIFO mode for the FIFOs because MMC FIFO addresses
+ * are not 256-bit (32-byte) aligned. So we use INCR, and the W8BIT
+ * parameter is ignored.
+ */
+ edma_set_src(sync_dev, src_port, INCR, W8BIT);
+ edma_set_dest(sync_dev, dst_port, INCR, W8BIT);
+
+ edma_set_src_index(sync_dev, src_bidx, src_cidx);
+ edma_set_dest_index(sync_dev, dst_bidx, dst_cidx);
+
+ edma_set_transfer_params(sync_dev, acnt, bcnt, ccnt, 8, ABSYNC);
+
+ edma_read_slot(sync_dev, template);
+
+ /* don't bother with irqs or chaining */
+ template->opt |= sync_dev << 12;
+}
+
+static void mmc_davinci_send_dma_request(struct mmc_davinci_host *host,
+ struct mmc_data *data)
+{
+ struct edmacc_param *template;
+ int channel, slot;
+ unsigned link;
+ struct scatterlist *sg;
+ unsigned sg_len;
+ unsigned bytes_left = host->bytes_left;
+ const unsigned shift = (rw_threshold == 32) ? 5 : 4;
+
+ if (host->data_dir == DAVINCI_MMC_DATADIR_WRITE) {
+ template = &host->tx_template;
+ channel = host->txdma;
+ } else {
+ template = &host->rx_template;
+ channel = host->rxdma;
+ }
+
+ /* We know sg_len and ccnt will never be out of range because
+ * we told the mmc layer which in turn tells the block layer
+ * to ensure that it only hands us one scatterlist segment
+ * per EDMA PARAM entry. Update the PARAM
+ * entries needed for each segment of this scatterlist.
+ */
+ for (slot = channel, link = 0, sg = data->sg, sg_len = host->sg_len;
+ sg_len-- != 0 && bytes_left;
+ sg = sg_next(sg), slot = host->links[link++]) {
+ u32 buf = sg_dma_address(sg);
+ unsigned count = sg_dma_len(sg);
+
+ template->link_bcntrld = sg_len
+ ? (host->links[link] << 5)
+ : 0xffff;
+
+ if (count > bytes_left)
+ count = bytes_left;
+ bytes_left -= count;
+
+ if (host->data_dir == DAVINCI_MMC_DATADIR_WRITE)
+ template->src = buf;
+ else
+ template->dst = buf;
+ template->ccnt = count >> shift;
+
+ edma_write_slot(slot, template);
+ }
+
+ edma_start(channel);
+}
+
+static int mmc_davinci_start_dma_transfer(struct mmc_davinci_host *host,
+ struct mmc_data *data)
+{
+ int i;
+ int mask = rw_threshold - 1;
+
+ host->sg_len = dma_map_sg(mmc_dev(host->mmc), data->sg, data->sg_len,
+ ((data->flags & MMC_DATA_WRITE)
+ ? DMA_TO_DEVICE
+ : DMA_FROM_DEVICE));
+
+ /* no individual DMA segment should need a partial FIFO */
+ for (i = 0; i < host->sg_len; i++) {
+ if (sg_dma_len(data->sg + i) & mask) {
+ dma_unmap_sg(mmc_dev(host->mmc),
+ data->sg, data->sg_len,
+ (data->flags & MMC_DATA_WRITE)
+ ? DMA_TO_DEVICE
+ : DMA_FROM_DEVICE);
+ return -1;
+ }
+ }
+
+ host->do_dma = 1;
+ mmc_davinci_send_dma_request(host, data);
+
+ return 0;
+}
+
+static void __init_or_module
+davinci_release_dma_channels(struct mmc_davinci_host *host)
+{
+ unsigned i;
+
+ if (!host->use_dma)
+ return;
+
+ for (i = 0; i < host->n_link; i++)
+ edma_free_slot(host->links[i]);
+
+ edma_free_channel(host->txdma);
+ edma_free_channel(host->rxdma);
+}
+
+static int __init davinci_acquire_dma_channels(struct mmc_davinci_host *host)
+{
+ int r, i;
+
+ /* Acquire master DMA write channel */
+ r = edma_alloc_channel(host->txdma, mmc_davinci_dma_cb, host,
+ EVENTQ_DEFAULT);
+ if (r < 0) {
+ dev_warn(mmc_dev(host->mmc), "alloc %s channel err %d\n",
+ "tx", r);
+ return r;
+ }
+ mmc_davinci_dma_setup(host, true, &host->tx_template);
+
+ /* Acquire master DMA read channel */
+ r = edma_alloc_channel(host->rxdma, mmc_davinci_dma_cb, host,
+ EVENTQ_DEFAULT);
+ if (r < 0) {
+ dev_warn(mmc_dev(host->mmc), "alloc %s channel err %d\n",
+ "rx", r);
+ goto free_master_write;
+ }
+ mmc_davinci_dma_setup(host, false, &host->rx_template);
+
+ /* Allocate parameter RAM slots, which will later be bound to a
+ * channel as needed to handle a scatterlist.
+ */
+ for (i = 0; i < ARRAY_SIZE(host->links); i++) {
+ r = edma_alloc_slot(EDMA_SLOT_ANY);
+ if (r < 0) {
+ dev_dbg(mmc_dev(host->mmc), "dma PaRAM alloc --> %d\n",
+ r);
+ break;
+ }
+ host->links[i] = r;
+ }
+ host->n_link = i;
+
+ return 0;
+
+free_master_write:
+ edma_free_channel(host->txdma);
+
+ return r;
+}
+
+/*----------------------------------------------------------------------*/
+
+static void
+mmc_davinci_prepare_data(struct mmc_davinci_host *host, struct mmc_request *req)
+{
+ int fifo_lev = (rw_threshold == 32) ? MMCFIFOCTL_FIFOLEV : 0;
+ int timeout;
+ struct mmc_data *data = req->data;
+
+ host->data = data;
+ if (data == NULL) {
+ host->data_dir = DAVINCI_MMC_DATADIR_NONE;
+ writel(0, host->base + DAVINCI_MMCBLEN);
+ writel(0, host->base + DAVINCI_MMCNBLK);
+ return;
+ }
+
+ dev_dbg(mmc_dev(host->mmc), "%s %s, %d blocks of %d bytes\n",
+ (data->flags & MMC_DATA_STREAM) ? "stream" : "block",
+ (data->flags & MMC_DATA_WRITE) ? "write" : "read",
+ data->blocks, data->blksz);
+ dev_dbg(mmc_dev(host->mmc), " DTO %d cycles + %d ns\n",
+ data->timeout_clks, data->timeout_ns);
+ timeout = data->timeout_clks + data->timeout_ns / ns_in_one_cycle;
+ if (timeout > 0xffff)
+ timeout = 0xffff;
+
+ writel(timeout, host->base + DAVINCI_MMCTOD);
+ writel(data->blocks, host->base + DAVINCI_MMCNBLK);
+ writel(data->blksz, host->base + DAVINCI_MMCBLEN);
+
+ /* Configure the FIFO */
+ switch (data->flags & MMC_DATA_WRITE) {
+ case MMC_DATA_WRITE:
+ host->data_dir = DAVINCI_MMC_DATADIR_WRITE;
+ writel(fifo_lev | MMCFIFOCTL_FIFODIR_WR | MMCFIFOCTL_FIFORST,
+ host->base + DAVINCI_MMCFIFOCTL);
+ writel(fifo_lev | MMCFIFOCTL_FIFODIR_WR,
+ host->base + DAVINCI_MMCFIFOCTL);
+ break;
+
+ default:
+ host->data_dir = DAVINCI_MMC_DATADIR_READ;
+ writel(fifo_lev | MMCFIFOCTL_FIFODIR_RD | MMCFIFOCTL_FIFORST,
+ host->base + DAVINCI_MMCFIFOCTL);
+ writel(fifo_lev | MMCFIFOCTL_FIFODIR_RD,
+ host->base + DAVINCI_MMCFIFOCTL);
+ break;
+ }
+
+ host->buffer = NULL;
+ host->bytes_left = data->blocks * data->blksz;
+
+ /* For now we try to use DMA whenever we won't need partial FIFO
+ * reads or writes, either for the whole transfer (as tested here)
+ * or for any individual scatterlist segment (tested when we call
+ * start_dma_transfer).
+ *
+ * While we *could* change that, unusual block sizes are rarely
+ * used. The occasional fallback to PIO should't hurt.
+ */
+ if (host->use_dma && (host->bytes_left & (rw_threshold - 1)) == 0
+ && mmc_davinci_start_dma_transfer(host, data) == 0) {
+ /* zero this to ensure we take no PIO paths */
+ host->bytes_left = 0;
+ } else {
+ /* Revert to CPU Copy */
+ host->sg_len = data->sg_len;
+ mmc_davinci_sg_to_buf(host);
+ }
+}
+
+static void mmc_davinci_request(struct mmc_host *mmc, struct mmc_request *req)
+{
+ struct mmc_davinci_host *host = mmc_priv(mmc);
+ unsigned long timeout = jiffies + msecs_to_jiffies(900);
+ u32 mmcst1 = 0;
+
+ /* Card may still be sending BUSY after a previous operation,
+ * typically some kind of write. If so, we can't proceed yet.
+ */
+ while (time_before(jiffies, timeout)) {
+ mmcst1 = readl(host->base + DAVINCI_MMCST1);
+ if (!(mmcst1 & MMCST1_BUSY))
+ break;
+ cpu_relax();
+ }
+ if (mmcst1 & MMCST1_BUSY) {
+ dev_err(mmc_dev(host->mmc), "still BUSY? bad ... \n");
+ req->cmd->error = -ETIMEDOUT;
+ mmc_request_done(mmc, req);
+ return;
+ }
+
+ host->do_dma = 0;
+ mmc_davinci_prepare_data(host, req);
+ mmc_davinci_start_command(host, req->cmd);
+}
+
+static unsigned int calculate_freq_for_card(struct mmc_davinci_host *host,
+ unsigned int mmc_req_freq)
+{
+ unsigned int mmc_freq = 0, cpu_arm_clk = 0, mmc_push_pull = 0;
+
+ cpu_arm_clk = host->mmc_input_clk;
+ if (mmc_req_freq && cpu_arm_clk > (2 * mmc_req_freq))
+ mmc_push_pull = ((unsigned int)cpu_arm_clk
+ / (2 * mmc_req_freq)) - 1;
+ else
+ mmc_push_pull = 0;
+
+ mmc_freq = (unsigned int)cpu_arm_clk / (2 * (mmc_push_pull + 1));
+
+ if (mmc_freq > mmc_req_freq)
+ mmc_push_pull = mmc_push_pull + 1;
+
+ /* Convert ns to clock cycles */
+ if (mmc_req_freq < 400000)
+ ns_in_one_cycle = 1000000 / ((cpu_arm_clk
+ / (2 * (mmc_push_pull + 1)))/1000);
+ else
+ ns_in_one_cycle = 1000000 / ((cpu_arm_clk
+ / (2 * (mmc_push_pull + 1)))/1000000);
+
+ return mmc_push_pull;
+}
+
+static void mmc_davinci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
+{
+ unsigned int open_drain_freq = 0, cpu_arm_clk = 0;
+ unsigned int mmc_push_pull_freq = 0;
+ struct mmc_davinci_host *host = mmc_priv(mmc);
+
+ cpu_arm_clk = host->mmc_input_clk;
+ dev_dbg(mmc_dev(host->mmc),
+ "clock %dHz busmode %d powermode %d Vdd %04x\n",
+ ios->clock, ios->bus_mode, ios->power_mode,
+ ios->vdd);
+ if (ios->bus_width == MMC_BUS_WIDTH_4) {
+ dev_dbg(mmc_dev(host->mmc), "Enabling 4 bit mode\n");
+ writel(readl(host->base + DAVINCI_MMCCTL) | MMCCTL_WIDTH_4_BIT,
+ host->base + DAVINCI_MMCCTL);
+ } else {
+ dev_dbg(mmc_dev(host->mmc), "Disabling 4 bit mode\n");
+ writel(readl(host->base + DAVINCI_MMCCTL) & ~MMCCTL_WIDTH_4_BIT,
+ host->base + DAVINCI_MMCCTL);
+ }
+
+ if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN) {
+ u32 temp;
+
+ /* Ignoring the init clock value passed for fixing the inter
+ * operability with different cards.
+ */
+ open_drain_freq = ((unsigned int)cpu_arm_clk
+ / (2 * MMCSD_INIT_CLOCK)) - 1;
+
+ if (open_drain_freq > 0xFF)
+ open_drain_freq = 0xFF;
+
+ temp = readl(host->base + DAVINCI_MMCCLK) & ~MMCCLK_CLKRT_MASK;
+ temp |= open_drain_freq;
+ writel(temp, host->base + DAVINCI_MMCCLK);
+
+ /* Convert ns to clock cycles */
+ ns_in_one_cycle = (1000000) / (MMCSD_INIT_CLOCK/1000);
+ } else {
+ u32 temp;
+ mmc_push_pull_freq = calculate_freq_for_card(host, ios->clock);
+
+ temp = readl(host->base + DAVINCI_MMCCLK) & ~MMCCLK_CLKEN;
+ writel(temp, host->base + DAVINCI_MMCCLK);
+
+ udelay(10);
+
+ temp = readl(host->base + DAVINCI_MMCCLK) & ~MMCCLK_CLKRT_MASK;
+ temp |= mmc_push_pull_freq;
+ writel(temp, host->base + DAVINCI_MMCCLK);
+
+ writel(temp | MMCCLK_CLKEN, host->base + DAVINCI_MMCCLK);
+
+ udelay(10);
+ }
+
+ host->bus_mode = ios->bus_mode;
+ if (ios->power_mode == MMC_POWER_UP) {
+ unsigned long timeout = jiffies + msecs_to_jiffies(50);
+ bool lose = true;
+
+ /* Send clock cycles, poll completion */
+ writel(0, host->base + DAVINCI_MMCARGHL);
+ writel(MMCCMD_INITCK, host->base + DAVINCI_MMCCMD);
+ while (time_before(jiffies, timeout)) {
+ u32 tmp = readl(host->base + DAVINCI_MMCST0);
+
+ if (tmp & MMCST0_RSPDNE) {
+ lose = false;
+ break;
+ }
+ cpu_relax();
+ }
+ if (lose)
+ dev_warn(mmc_dev(host->mmc), "powerup timeout\n");
+ }
+
+ /* FIXME on power OFF, reset things ... */
+}
+
+static void
+mmc_davinci_xfer_done(struct mmc_davinci_host *host, struct mmc_data *data)
+{
+ host->data = NULL;
+ host->data_dir = DAVINCI_MMC_DATADIR_NONE;
+
+ if (host->do_dma) {
+ davinci_abort_dma(host);
+
+ dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len,
+ (data->flags & MMC_DATA_WRITE)
+ ? DMA_TO_DEVICE
+ : DMA_FROM_DEVICE);
+ host->do_dma = false;
+ }
+
+ if (!data->stop || (host->cmd && host->cmd->error)) {
+ mmc_request_done(host->mmc, data->mrq);
+ writel(0, host->base + DAVINCI_MMCIM);
+ } else
+ mmc_davinci_start_command(host, data->stop);
+}
+
+static void mmc_davinci_cmd_done(struct mmc_davinci_host *host,
+ struct mmc_command *cmd)
+{
+ host->cmd = NULL;
+
+ if (cmd->flags & MMC_RSP_PRESENT) {
+ if (cmd->flags & MMC_RSP_136) {
+ /* response type 2 */
+ cmd->resp[3] = readl(host->base + DAVINCI_MMCRSP01);
+ cmd->resp[2] = readl(host->base + DAVINCI_MMCRSP23);
+ cmd->resp[1] = readl(host->base + DAVINCI_MMCRSP45);
+ cmd->resp[0] = readl(host->base + DAVINCI_MMCRSP67);
+ } else {
+ /* response types 1, 1b, 3, 4, 5, 6 */
+ cmd->resp[0] = readl(host->base + DAVINCI_MMCRSP67);
+ }
+ }
+
+ if (host->data == NULL || cmd->error) {
+ if (cmd->error == -ETIMEDOUT)
+ cmd->mrq->cmd->retries = 0;
+ mmc_request_done(host->mmc, cmd->mrq);
+ writel(0, host->base + DAVINCI_MMCIM);
+ }
+}
+
+static void
+davinci_abort_data(struct mmc_davinci_host *host, struct mmc_data *data)
+{
+ u32 temp;
+
+ /* reset command and data state machines */
+ temp = readl(host->base + DAVINCI_MMCCTL);
+ writel(temp | MMCCTL_CMDRST | MMCCTL_DATRST,
+ host->base + DAVINCI_MMCCTL);
+
+ temp &= ~(MMCCTL_CMDRST | MMCCTL_DATRST);
+ udelay(10);
+ writel(temp, host->base + DAVINCI_MMCCTL);
+}
+
+static irqreturn_t mmc_davinci_irq(int irq, void *dev_id)
+{
+ struct mmc_davinci_host *host = (struct mmc_davinci_host *)dev_id;
+ unsigned int status, qstatus;
+ int end_command = 0;
+ int end_transfer = 0;
+ struct mmc_data *data = host->data;
+
+ if (host->cmd == NULL && host->data == NULL) {
+ status = readl(host->base + DAVINCI_MMCST0);
+ dev_dbg(mmc_dev(host->mmc),
+ "Spurious interrupt 0x%04x\n", status);
+ /* Disable the interrupt from mmcsd */
+ writel(0, host->base + DAVINCI_MMCIM);
+ return IRQ_NONE;
+ }
+
+ status = readl(host->base + DAVINCI_MMCST0);
+ qstatus = status;
+
+ /* handle FIFO first when using PIO for data.
+ * bytes_left will decrease to zero as I/O progress and status will
+ * read zero over iteration because this controller status
+ * register(MMCST0) reports any status only once and it is cleared
+ * by read. So, it is not unbouned loop even in the case of
+ * non-dma.
+ */
+ while (host->bytes_left && (status & (MMCST0_DXRDY | MMCST0_DRRDY))) {
+ davinci_fifo_data_trans(host, rw_threshold);
+ status = readl(host->base + DAVINCI_MMCST0);
+ if (!status)
+ break;
+ qstatus |= status;
+ }
+
+ if (qstatus & MMCST0_DATDNE) {
+ /* All blocks sent/received, and CRC checks passed */
+ if (data != NULL) {
+ if ((host->do_dma == 0) && (host->bytes_left > 0)) {
+ /* if datasize < rw_threshold
+ * no RX ints are generated
+ */
+ davinci_fifo_data_trans(host, host->bytes_left);
+ }
+ end_transfer = 1;
+ data->bytes_xfered = data->blocks * data->blksz;
+ } else {
+ dev_err(mmc_dev(host->mmc),
+ "DATDNE with no host->data\n");
+ }
+ }
+
+ if (qstatus & MMCST0_TOUTRD) {
+ /* Read data timeout */
+ data->error = -ETIMEDOUT;
+ end_transfer = 1;
+
+ dev_dbg(mmc_dev(host->mmc),
+ "read data timeout, status %x\n",
+ qstatus);
+
+ davinci_abort_data(host, data);
+ }
+
+ if (qstatus & (MMCST0_CRCWR | MMCST0_CRCRD)) {
+ /* Data CRC error */
+ data->error = -EILSEQ;
+ end_transfer = 1;
+
+ /* NOTE: this controller uses CRCWR to report both CRC
+ * errors and timeouts (on writes). MMCDRSP values are
+ * only weakly documented, but 0x9f was clearly a timeout
+ * case and the two three-bit patterns in various SD specs
+ * (101, 010) aren't part of it ...
+ */
+ if (qstatus & MMCST0_CRCWR) {
+ u32 temp = readb(host->base + DAVINCI_MMCDRSP);
+
+ if (temp == 0x9f)
+ data->error = -ETIMEDOUT;
+ }
+ dev_dbg(mmc_dev(host->mmc), "data %s %s error\n",
+ (qstatus & MMCST0_CRCWR) ? "write" : "read",
+ (data->error == -ETIMEDOUT) ? "timeout" : "CRC");
+
+ davinci_abort_data(host, data);
+ }
+
+ if (qstatus & MMCST0_TOUTRS) {
+ /* Command timeout */
+ if (host->cmd) {
+ dev_dbg(mmc_dev(host->mmc),
+ "CMD%d timeout, status %x\n",
+ host->cmd->opcode, qstatus);
+ host->cmd->error = -ETIMEDOUT;
+ if (data) {
+ end_transfer = 1;
+ davinci_abort_data(host, data);
+ } else
+ end_command = 1;
+ }
+ }
+
+ if (qstatus & MMCST0_CRCRS) {
+ /* Command CRC error */
+ dev_dbg(mmc_dev(host->mmc), "Command CRC error\n");
+ if (host->cmd) {
+ host->cmd->error = -EILSEQ;
+ end_command = 1;
+ }
+ }
+
+ if (qstatus & MMCST0_RSPDNE) {
+ /* End of command phase */
+ end_command = (int) host->cmd;
+ }
+
+ if (end_command)
+ mmc_davinci_cmd_done(host, host->cmd);
+ if (end_transfer)
+ mmc_davinci_xfer_done(host, data);
+ return IRQ_HANDLED;
+}
+
+static int mmc_davinci_get_cd(struct mmc_host *mmc)
+{
+ struct platform_device *pdev = to_platform_device(mmc->parent);
+ struct davinci_mmc_config *config = pdev->dev.platform_data;
+
+ if (!config || !config->get_cd)
+ return -ENOSYS;
+ return config->get_cd(pdev->id);
+}
+
+static int mmc_davinci_get_ro(struct mmc_host *mmc)
+{
+ struct platform_device *pdev = to_platform_device(mmc->parent);
+ struct davinci_mmc_config *config = pdev->dev.platform_data;
+
+ if (!config || !config->get_ro)
+ return -ENOSYS;
+ return config->get_ro(pdev->id);
+}
+
+static struct mmc_host_ops mmc_davinci_ops = {
+ .request = mmc_davinci_request,
+ .set_ios = mmc_davinci_set_ios,
+ .get_cd = mmc_davinci_get_cd,
+ .get_ro = mmc_davinci_get_ro,
+};
+
+/*----------------------------------------------------------------------*/
+
+static void __init init_mmcsd_host(struct mmc_davinci_host *host)
+{
+ /* DAT line portion is diabled and in reset state */
+ writel(readl(host->base + DAVINCI_MMCCTL) | MMCCTL_DATRST,
+ host->base + DAVINCI_MMCCTL);
+
+ /* CMD line portion is diabled and in reset state */
+ writel(readl(host->base + DAVINCI_MMCCTL) | MMCCTL_CMDRST,
+ host->base + DAVINCI_MMCCTL);
+
+ udelay(10);
+
+ writel(0, host->base + DAVINCI_MMCCLK);
+ writel(MMCCLK_CLKEN, host->base + DAVINCI_MMCCLK);
+
+ writel(0x1FFF, host->base + DAVINCI_MMCTOR);
+ writel(0xFFFF, host->base + DAVINCI_MMCTOD);
+
+ writel(readl(host->base + DAVINCI_MMCCTL) & ~MMCCTL_DATRST,
+ host->base + DAVINCI_MMCCTL);
+ writel(readl(host->base + DAVINCI_MMCCTL) & ~MMCCTL_CMDRST,
+ host->base + DAVINCI_MMCCTL);
+
+ udelay(10);
+}
+
+static int __init davinci_mmcsd_probe(struct platform_device *pdev)
+{
+ struct davinci_mmc_config *pdata = pdev->dev.platform_data;
+ struct mmc_davinci_host *host = NULL;
+ struct mmc_host *mmc = NULL;
+ struct resource *r, *mem = NULL;
+ int ret = 0, irq = 0;
+ size_t mem_size;
+
+ /* REVISIT: when we're fully converted, fail if pdata is NULL */
+
+ ret = -ENODEV;
+ r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ irq = platform_get_irq(pdev, 0);
+ if (!r || irq == NO_IRQ)
+ goto out;
+
+ ret = -EBUSY;
+ mem_size = resource_size(r);
+ mem = request_mem_region(r->start, mem_size, pdev->name);
+ if (!mem)
+ goto out;
+
+ ret = -ENOMEM;
+ mmc = mmc_alloc_host(sizeof(struct mmc_davinci_host), &pdev->dev);
+ if (!mmc)
+ goto out;
+
+ host = mmc_priv(mmc);
+ host->mmc = mmc; /* Important */
+
+ r = platform_get_resource(pdev, IORESOURCE_DMA, 0);
+ if (!r)
+ goto out;
+ host->rxdma = r->start;
+
+ r = platform_get_resource(pdev, IORESOURCE_DMA, 1);
+ if (!r)
+ goto out;
+ host->txdma = r->start;
+
+ host->mem_res = mem;
+ host->base = ioremap(mem->start, mem_size);
+ if (!host->base)
+ goto out;
+
+ ret = -ENXIO;
+ host->clk = clk_get(&pdev->dev, "MMCSDCLK");
+ if (IS_ERR(host->clk)) {
+ ret = PTR_ERR(host->clk);
+ goto out;
+ }
+ clk_enable(host->clk);
+ host->mmc_input_clk = clk_get_rate(host->clk);
+
+ init_mmcsd_host(host);
+
+ host->use_dma = use_dma;
+ host->irq = irq;
+
+ if (host->use_dma && davinci_acquire_dma_channels(host) != 0)
+ host->use_dma = 0;
+
+ /* REVISIT: someday, support IRQ-driven card detection. */
+ mmc->caps |= MMC_CAP_NEEDS_POLL;
+
+ if (!pdata || pdata->wires == 4 || pdata->wires == 0)
+ mmc->caps |= MMC_CAP_4_BIT_DATA;
+
+ mmc->ops = &mmc_davinci_ops;
+ mmc->f_min = 312500;
+ mmc->f_max = 25000000;
+ if (pdata && pdata->max_freq)
+ mmc->f_max = pdata->max_freq;
+ if (pdata && pdata->caps)
+ mmc->caps |= pdata->caps;
+ mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
+
+ /* With no iommu coalescing pages, each phys_seg is a hw_seg.
+ * Each hw_seg uses one EDMA parameter RAM slot, always one
+ * channel and then usually some linked slots.
+ */
+ mmc->max_hw_segs = 1 + host->n_link;
+ mmc->max_phys_segs = mmc->max_hw_segs;
+
+ /* EDMA limit per hw segment (one or two MBytes) */
+ mmc->max_seg_size = MAX_CCNT * rw_threshold;
+
+ /* MMC/SD controller limits for multiblock requests */
+ mmc->max_blk_size = 4095; /* BLEN is 12 bits */
+ mmc->max_blk_count = 65535; /* NBLK is 16 bits */
+ mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count;
+
+ dev_dbg(mmc_dev(host->mmc), "max_phys_segs=%d\n", mmc->max_phys_segs);
+ dev_dbg(mmc_dev(host->mmc), "max_hw_segs=%d\n", mmc->max_hw_segs);
+ dev_dbg(mmc_dev(host->mmc), "max_blk_size=%d\n", mmc->max_blk_size);
+ dev_dbg(mmc_dev(host->mmc), "max_req_size=%d\n", mmc->max_req_size);
+ dev_dbg(mmc_dev(host->mmc), "max_seg_size=%d\n", mmc->max_seg_size);
+
+ platform_set_drvdata(pdev, host);
+
+ ret = mmc_add_host(mmc);
+ if (ret < 0)
+ goto out;
+
+ ret = request_irq(irq, mmc_davinci_irq, 0, mmc_hostname(mmc), host);
+ if (ret)
+ goto out;
+
+ rename_region(mem, mmc_hostname(mmc));
+
+ dev_info(mmc_dev(host->mmc), "Using %s, %d-bit mode\n",
+ host->use_dma ? "DMA" : "PIO",
+ (mmc->caps & MMC_CAP_4_BIT_DATA) ? 4 : 1);
+
+ return 0;
+
+out:
+ if (host) {
+ davinci_release_dma_channels(host);
+
+ if (host->clk) {
+ clk_disable(host->clk);
+ clk_put(host->clk);
+ }
+
+ if (host->base)
+ iounmap(host->base);
+ }
+
+ if (mmc)
+ mmc_free_host(mmc);
+
+ if (mem)
+ release_resource(mem);
+
+ dev_dbg(&pdev->dev, "probe err %d\n", ret);
+
+ return ret;
+}
+
+static int __exit davinci_mmcsd_remove(struct platform_device *pdev)
+{
+ struct mmc_davinci_host *host = platform_get_drvdata(pdev);
+
+ platform_set_drvdata(pdev, NULL);
+ if (host) {
+ mmc_remove_host(host->mmc);
+ free_irq(host->irq, host);
+
+ davinci_release_dma_channels(host);
+
+ clk_disable(host->clk);
+ clk_put(host->clk);
+
+ iounmap(host->base);
+
+ release_resource(host->mem_res);
+
+ mmc_free_host(host->mmc);
+ }
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int davinci_mmcsd_suspend(struct platform_device *pdev, pm_message_t msg)
+{
+ struct mmc_davinci_host *host = platform_get_drvdata(pdev);
+
+ return mmc_suspend_host(host->mmc, msg);
+}
+
+static int davinci_mmcsd_resume(struct platform_device *pdev)
+{
+ struct mmc_davinci_host *host = platform_get_drvdata(pdev);
+
+ return mmc_resume_host(host->mmc);
+}
+#else
+#define davinci_mmcsd_suspend NULL
+#define davinci_mmcsd_resume NULL
+#endif
+
+static struct platform_driver davinci_mmcsd_driver = {
+ .driver = {
+ .name = "davinci_mmc",
+ .owner = THIS_MODULE,
+ },
+ .remove = __exit_p(davinci_mmcsd_remove),
+ .suspend = davinci_mmcsd_suspend,
+ .resume = davinci_mmcsd_resume,
+};
+
+static int __init davinci_mmcsd_init(void)
+{
+ return platform_driver_probe(&davinci_mmcsd_driver,
+ davinci_mmcsd_probe);
+}
+module_init(davinci_mmcsd_init);
+
+static void __exit davinci_mmcsd_exit(void)
+{
+ platform_driver_unregister(&davinci_mmcsd_driver);
+}
+module_exit(davinci_mmcsd_exit);
+
+MODULE_AUTHOR("Texas Instruments India");
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("MMC/SD driver for Davinci MMC controller");
+
--
1.5.4.1
On Thu, 2 Apr 2009 15:26:36 +0530
Purushotam Kumar <[email protected]> wrote:
> arch/arm/mach-davinci/include/mach/mmc.h | 25 +
> drivers/mmc/host/Kconfig | 8 +
> drivers/mmc/host/Makefile | 1 +
> drivers/mmc/host/davinci_mmc.c | 1264 ++++++++++++++++++++++++++++++
> 4 files changed, 1298 insertions(+), 0 deletions(-)
> create mode 100644 arch/arm/mach-davinci/include/mach/mmc.h
> create mode 100644 drivers/mmc/host/davinci_mmc.c
I want a MAINTAINERS entry for this driver as well.
> + /*
> + * Before non-DMA WRITE commands the controller needs priming:
> + * FIFO should be populated with 32 bytes i.e. whatever is the FIFO size
> + */
> + if (!host->do_dma && (host->data_dir == DAVINCI_MMC_DATADIR_WRITE) &&
> + ((cmd->opcode == MMC_WRITE_BLOCK) ||
> + (cmd->opcode == MMC_WRITE_MULTIPLE_BLOCK)))
> + davinci_fifo_data_trans(host, DAVINCI_MMC_FIFO_SIZE_BYTE);
I'm still not following the requirements here. Why would the hardware
only need to have the FIFO primed for those two commands and not every
kind of write?
> +
> + /* We know sg_len and ccnt will never be out of range because
> + * we told the mmc layer which in turn tells the block layer
> + * to ensure that it only hands us one scatterlist segment
> + * per EDMA PARAM entry. Update the PARAM
> + * entries needed for each segment of this scatterlist.
> + */
> + for (slot = channel, link = 0, sg = data->sg, sg_len = host->sg_len;
> + sg_len-- != 0 && bytes_left;
> + sg = sg_next(sg), slot = host->links[link++]) {
You might be able to make this cleaner using the for_each_sg helper.
> +static unsigned int calculate_freq_for_card(struct mmc_davinci_host *host,
> + unsigned int mmc_req_freq)
> +{
> + unsigned int mmc_freq = 0, cpu_arm_clk = 0, mmc_push_pull = 0;
> +
> + cpu_arm_clk = host->mmc_input_clk;
> + if (mmc_req_freq && cpu_arm_clk > (2 * mmc_req_freq))
> + mmc_push_pull = ((unsigned int)cpu_arm_clk
> + / (2 * mmc_req_freq)) - 1;
> + else
> + mmc_push_pull = 0;
> +
> + mmc_freq = (unsigned int)cpu_arm_clk / (2 * (mmc_push_pull + 1));
> +
> + if (mmc_freq > mmc_req_freq)
> + mmc_push_pull = mmc_push_pull + 1;
The naming of the divider is a bit confusing here. :)
> +
> + /* Convert ns to clock cycles */
> + if (mmc_req_freq < 400000)
> + ns_in_one_cycle = 1000000 / ((cpu_arm_clk
> + / (2 * (mmc_push_pull + 1)))/1000);
> + else
> + ns_in_one_cycle = 1000000 / ((cpu_arm_clk
> + / (2 * (mmc_push_pull + 1)))/1000000);
> +
The clock frequency is per host, so store this in the mmc_davinci_host
structure.
> + if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN) {
> + u32 temp;
> +
> + /* Ignoring the init clock value passed for fixing the inter
> + * operability with different cards.
> + */
> + open_drain_freq = ((unsigned int)cpu_arm_clk
> + / (2 * MMCSD_INIT_CLOCK)) - 1;
> +
> + if (open_drain_freq > 0xFF)
> + open_drain_freq = 0xFF;
> +
> + temp = readl(host->base + DAVINCI_MMCCLK) & ~MMCCLK_CLKRT_MASK;
> + temp |= open_drain_freq;
> + writel(temp, host->base + DAVINCI_MMCCLK);
> +
> + /* Convert ns to clock cycles */
> + ns_in_one_cycle = (1000000) / (MMCSD_INIT_CLOCK/1000);
I'm still not sure why you need this. Open drain mode is always used at
a low frequency anyway.
Rgds
--
-- Pierre Ossman
Linux kernel, MMC maintainer http://www.kernel.org
rdesktop, core developer http://www.rdesktop.org
TigerVNC, core developer http://www.tigervnc.org
WARNING: This correspondence is being monitored by the
Swedish government. Make sure your server uses encryption
for SMTP traffic and consider using PGP for end-to-end
encryption.
> > drivers/mmc/host/davinci_mmc.c | 1264 ++++++++++++++++++++++++++++++
> > 4 files changed, 1298 insertions(+), 0 deletions(-)
> > create mode 100644 arch/arm/mach-davinci/include/mach/mmc.h
> > create mode 100644 drivers/mmc/host/davinci_mmc.c
>
> I want a MAINTAINERS entry for this driver as well.
I will add this and re-submit the patch. I will provide e-mail id in the MODULE_AUTHOR.
>
> > + /*
> > + * Before non-DMA WRITE commands the controller needs priming:
> > + * FIFO should be populated with 32 bytes i.e. whatever is the FIFO size
> > + */
> > + if (!host->do_dma && (host->data_dir == DAVINCI_MMC_DATADIR_WRITE) &&
> > + ((cmd->opcode == MMC_WRITE_BLOCK) ||
> > + (cmd->opcode == MMC_WRITE_MULTIPLE_BLOCK)))
> > + davinci_fifo_data_trans(host, DAVINCI_MMC_FIFO_SIZE_BYTE);
>
> I'm still not following the requirements here. Why would the hardware
> only need to have the FIFO primed for those two commands and not every
> kind of write?
This required by SD controller as suggested by IP designer. Please look at SD controller spec at http://www.ti.com/litv/pdf/sprue30d . Please check section 3.2/3.6 and point no 11/10 in the controller spec. It does not talk about priming by 32 bytes for any other command. This restriction is from SD controller.
>
> > +
> > + /* We know sg_len and ccnt will never be out of range because
> > + * we told the mmc layer which in turn tells the block layer
> > + * to ensure that it only hands us one scatterlist segment
> > + * per EDMA PARAM entry. Update the PARAM
> > + * entries needed for each segment of this scatterlist.
> > + */
> > + for (slot = channel, link = 0, sg = data->sg, sg_len = host->sg_len;
> > + sg_len-- != 0 && bytes_left;
> > + sg = sg_next(sg), slot = host->links[link++]) {
>
> You might be able to make this cleaner using the for_each_sg helper.
That particular loop can't use for_each_sg() since it's also iterating the EDMA slots: channel, then links[]
>
> > +static unsigned int calculate_freq_for_card(struct mmc_davinci_host *host,
> > + unsigned int mmc_req_freq)
> > +{
> > + unsigned int mmc_freq = 0, cpu_arm_clk = 0, mmc_push_pull = 0;
> > +
> > + cpu_arm_clk = host->mmc_input_clk;
> > + if (mmc_req_freq && cpu_arm_clk > (2 * mmc_req_freq))
> > + mmc_push_pull = ((unsigned int)cpu_arm_clk
> > + / (2 * mmc_req_freq)) - 1;
> > + else
> > + mmc_push_pull = 0;
> > +
> > + mmc_freq = (unsigned int)cpu_arm_clk / (2 * (mmc_push_pull + 1));
> > +
> > + if (mmc_freq > mmc_req_freq)
> > + mmc_push_pull = mmc_push_pull + 1;
>
> The naming of the divider is a bit confusing here. :)
I am thinking to change " mmc_push_pull" to " mmc_push_pull_divider". Please suggest other appropriate name.
>
> > +
> > + /* Convert ns to clock cycles */
> > + if (mmc_req_freq < 400000)
> > + ns_in_one_cycle = 1000000 / ((cpu_arm_clk
> > + / (2 * (mmc_push_pull + 1)))/1000);
> > + else
> > + ns_in_one_cycle = 1000000 / ((cpu_arm_clk
> > + / (2 * (mmc_push_pull + 1)))/1000000);
> > +
>
> The clock frequency is per host, so store this in the mmc_davinci_host
> structure.
You are correct and I will implement and re-submit the patch.
>
> > + if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN) {
> > + u32 temp;
> > +
> > + /* Ignoring the init clock value passed for fixing the inter
> > + * operability with different cards.
> > + */
> > + open_drain_freq = ((unsigned int)cpu_arm_clk
> > + / (2 * MMCSD_INIT_CLOCK)) - 1;
> > +
> > + if (open_drain_freq > 0xFF)
> > + open_drain_freq = 0xFF;
> > +
> > + temp = readl(host->base + DAVINCI_MMCCLK) & ~MMCCLK_CLKRT_MASK;
> > + temp |= open_drain_freq;
> > + writel(temp, host->base + DAVINCI_MMCCLK);
> > +
> > + /* Convert ns to clock cycles */
> > + ns_in_one_cycle = (1000000) / (MMCSD_INIT_CLOCK/1000);
>
> I'm still not sure why you need this. Open drain mode is always used at
> a low frequency anyway.
If my understanding is correct you are suggesting that at lower freq. there is no need to update the timeout parameter and can use the default value of ns_in_one_cycle.
The mmc_davinci_prepare_data() may be called even during open drain frequency mode and here we are calculating the timeout value and updating the timeout reg. So ns_in_one_cycle should hold a proper value once we call mmc_davinci_prepare_data(). I think there is no harm in having this calculation here.
Regards,
Purushotam
On Friday 17 April 2009, Kumar, Purushotam wrote:
>
> > I'm still not following the requirements here. Why would the hardware
> > only need to have the FIFO primed for those two commands and not every
> > kind of write?
>
> This required by SD controller as suggested by IP designer. Please
> look at SD controller spec at http://www.ti.com/litv/pdf/sprue30d .
> Please check section 3.2/3.6 and point no 11/10 in the controller spec.
Those are in Chapter 3, "Procedures for Common Operations" ...
that is, examples. Examples, as a rule, are there just to
elaborate ("unpack") the more detailed text, not substitute
for clear specification. (And TI is generally pretty good
about providing sane documentation, thank you! Fewer problems
than with "some" vendors.)
In this case the spec says in a note in 2.7.2 that priming
the fifo is needed for "write transactions" ... since no
"fifo became empty" IRQ is generated. It does not limit it
to the WRITE_BLOCK and WRITE_MULTIPLE_BLOCK commands.
Those examples are for writing single and multiple blocks; there
are no SDIO write operations shown, for example, or password
passing operations. Those would also suffer from the lack of
a "fifo became empty" IRQ.
> It does not talk about priming by 32 bytes for any other command.
Said diffferently, *every* PIO write transaction shown primes
the fifo ... but there are no examples of non-block writes.
> This restriction is from SD controller.
Could you confirm that interpretation with the folk who have
provided that silicon block?
If your reading is correct, and it's really a restriction to
those two commands, the documentation should change to say
that "single and multiple block write commands" require FIFO
priming ... not all "write transactions" as now written.
- Dave
> >
> > This required by SD controller as suggested by IP designer. Please
> > look at SD controller spec at http://www.ti.com/litv/pdf/sprue30d .
> > Please check section 3.2/3.6 and point no 11/10 in the controller spec.
>
> In this case the spec says in a note in 2.7.2 that priming
> the fifo is needed for "write transactions" ... since no
> "fifo became empty" IRQ is generated. It does not limit it
> to the WRITE_BLOCK and WRITE_MULTIPLE_BLOCK commands.
>
> Those examples are for writing single and multiple blocks; there
> are no SDIO write operations shown, for example, or password
> passing operations. Those would also suffer from the lack of
> a "fifo became empty" IRQ.
>
It seems you are right that FIFO is required to be primed before any write transaction.
> > It does not talk about priming by 32 bytes for any other command.
> Said diffferently, *every* PIO write transaction shown primes
> the fifo ... but there are no examples of non-block writes.
We need to prime the FIFO beforehand with whatever data we intend to transfer. We looked into SDIO driver on DM6446 and observed that it requires priming.
> > This restriction is from SD controller.
>
> Could you confirm that interpretation with the folk who have
> provided that silicon block?
>
> If your reading is correct, and it's really a restriction to
> those two commands, the documentation should change to say
> that "single and multiple block write commands" require FIFO
> priming ... not all "write transactions" as now written.
Apart from above there was a doubt for:
if (!host->do_dma && (host->data_dir == DAVINCI_MMC_DATADIR_WRITE))
davinci_fifo_data_trans(host, 32);
We will also remove check for CMD25 and CMD24 before priming and so it will allow priming for all commands.
Although there does seem to be a bug there ... it should never fill the
fifo with more data than is being sent.
The second parameter is rightly justified as it is the length of fifo. If
you see inside the davinci_fifo_data_trans() the FIFO is only primed based
upon the data size during that transfer. So in a way we are not filling the
fifo with more data.
We will re-submit patch tomorrow. Please let us know if you have any further concerns.
Regards,
Purushotam
On Fri, 17 Apr 2009 16:34:22 +0530
"Kumar, Purushotam" <[email protected]> wrote:
> > > +
> > > + if (mmc_freq > mmc_req_freq)
> > > + mmc_push_pull = mmc_push_pull + 1;
> >
> > The naming of the divider is a bit confusing here. :)
>
> I am thinking to change " mmc_push_pull" to " mmc_push_pull_divider". Please suggest other appropriate name.
>
Or just "divider". The rest should be clear from the context.
> > > + if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN) {
> > > + u32 temp;
> > > +
> > > + /* Ignoring the init clock value passed for fixing the inter
> > > + * operability with different cards.
> > > + */
> > > + open_drain_freq = ((unsigned int)cpu_arm_clk
> > > + / (2 * MMCSD_INIT_CLOCK)) - 1;
> > > +
> > > + if (open_drain_freq > 0xFF)
> > > + open_drain_freq = 0xFF;
> > > +
> > > + temp = readl(host->base + DAVINCI_MMCCLK) & ~MMCCLK_CLKRT_MASK;
> > > + temp |= open_drain_freq;
> > > + writel(temp, host->base + DAVINCI_MMCCLK);
> > > +
> > > + /* Convert ns to clock cycles */
> > > + ns_in_one_cycle = (1000000) / (MMCSD_INIT_CLOCK/1000);
> >
> > I'm still not sure why you need this. Open drain mode is always used at
> > a low frequency anyway.
>
>
> If my understanding is correct you are suggesting that at lower freq. there is no need to update the timeout parameter and can use the default value of ns_in_one_cycle.
>
> The mmc_davinci_prepare_data() may be called even during open drain frequency mode and here we are calculating the timeout value and updating the timeout reg. So ns_in_one_cycle should hold a proper value once we call mmc_davinci_prepare_data(). I think there is no harm in having this calculation here.
>
I see. I thought this was some fiddling to override the core's decision
on clock frequency.
Why do you need to calculate the timeout differently based on
push-pull/open drain mode though?
Rgds
--
-- Pierre Ossman
Linux kernel, MMC maintainer http://www.kernel.org
rdesktop, core developer http://www.rdesktop.org
TigerVNC, core developer http://www.tigervnc.org
WARNING: This correspondence is being monitored by the
Swedish government. Make sure your server uses encryption
for SMTP traffic and consider using PGP for end-to-end
encryption.