With CONFIG_PM=y, the omapfb/lcdc device on Amstrad Delta, after initially
starting correctly, breaks with the following error messages:
omapfb omapfb: resetting (status 0xffffff96,reset count 1)
...
omapfb omapfb: resetting (status 0xffffff96,reset count 100)
omapfb omapfb: too many reset attempts, giving up.
Looking closer at this I have found that it had been broken almost 2 years ago
with commit 2418996e3b100114edb2ae110d5d4acb928909d2, PM fixes for OMAP1.
The definite reason for broken omapfb/lcdc behavoiur in PM mode
appeared to be ARM_IDLECT1:IDLIF_ARM (bit 6) put into idle regardless of LCD
DMA possibly running. The bit were set based on return value of the
omap_dma_running() function that did not check for dedicated LCD DMA
channel status. The patch below fixes this.
Created and tested against linux-2.6.32-rc5
Signed-off-by: Janusz Krzysztofik <[email protected]>
---
Hi,
If there are still no comments, especially on the bug possible impact on other
OMAP1510 boards (or even OMAP1610 with internal LCD controller), then Tony,
please apply it as is. Until it is accepted, I am stuck with new
ams_delta_defconfig.
Thanks,
Janusz
--- linux-2.6.32-rc5/arch/arm/plat-omap/dma.c.orig 2009-10-16 02:41:50.000000000 +0200
+++ linux-2.6.32-rc5/arch/arm/plat-omap/dma.c 2009-11-03 20:15:35.000000000 +0100
@@ -30,6 +30,7 @@
#include <linux/irq.h>
#include <linux/io.h>
+#include <asm/mach-types.h>
#include <asm/system.h>
#include <mach/hardware.h>
#include <mach/dma.h>
@@ -1110,6 +1111,14 @@ int omap_dma_running(void)
{
int lch;
+ /*
+ * On Amstrad Delta, the OMAP internal LCD controller will start the
+ * transfer when it gets enabled, so assume DMA running if LCD enabled.
+ */
+ if (machine_is_ams_delta())
+ if (omap_readw(0xfffec000 + 0x00) & (1 << 0))
+ return 1;
+
/* Check if LCD DMA is running */
if (cpu_is_omap16xx())
if (omap_readw(OMAP1610_DMA_LCD_CCR) & OMAP_DMA_CCR_EN)
Tuesday 03 November 2009 20:24:38 Janusz Krzysztofik napisał(a):
> If there are still no comments, especially on the bug possible impact on
> other OMAP1510 boards (or even OMAP1610 with internal LCD controller), then
> Tony, please apply it as is. Until it is accepted, I am stuck with new
> ams_delta_defconfig.
Tony,
Sorry, I've not checked for new mail before posting this one and missed your
acceptance for my idea of fixing all omap1510, not only ams_delta. If there
are no more comments, I'll submit v3 with cpu_is_omap1510() replacing
machine_is_ams_delta().
Thanks,
Janusz
> --- linux-2.6.32-rc5/arch/arm/plat-omap/dma.c.orig 2009-10-16
> 02:41:50.000000000 +0200 +++
> linux-2.6.32-rc5/arch/arm/plat-omap/dma.c 2009-11-03 20:15:35.000000000
> +0100 @@ -30,6 +30,7 @@
> #include <linux/irq.h>
> #include <linux/io.h>
>
> +#include <asm/mach-types.h>
> #include <asm/system.h>
> #include <mach/hardware.h>
> #include <mach/dma.h>
> @@ -1110,6 +1111,14 @@ int omap_dma_running(void)
> {
> int lch;
>
> + /*
> + * On Amstrad Delta, the OMAP internal LCD controller will start the
> + * transfer when it gets enabled, so assume DMA running if LCD enabled.
> + */
> + if (machine_is_ams_delta())
> + if (omap_readw(0xfffec000 + 0x00) & (1 << 0))
> + return 1;
> +
> /* Check if LCD DMA is running */
> if (cpu_is_omap16xx())
> if (omap_readw(OMAP1610_DMA_LCD_CCR) & OMAP_DMA_CCR_EN)
* Janusz Krzysztofik <[email protected]> [091103 12:05]:
> Tuesday 03 November 2009 20:24:38 Janusz Krzysztofik napisał(a):
> > If there are still no comments, especially on the bug possible impact on
> > other OMAP1510 boards (or even OMAP1610 with internal LCD controller), then
> > Tony, please apply it as is. Until it is accepted, I am stuck with new
> > ams_delta_defconfig.
>
> Tony,
> Sorry, I've not checked for new mail before posting this one and missed your
> acceptance for my idea of fixing all omap1510, not only ams_delta. If there
> are no more comments, I'll submit v3 with cpu_is_omap1510() replacing
> machine_is_ams_delta().
Sounds good to me.
Tony
> Thanks,
> Janusz
>
> > --- linux-2.6.32-rc5/arch/arm/plat-omap/dma.c.orig 2009-10-16
> > 02:41:50.000000000 +0200 +++
> > linux-2.6.32-rc5/arch/arm/plat-omap/dma.c 2009-11-03 20:15:35.000000000
> > +0100 @@ -30,6 +30,7 @@
> > #include <linux/irq.h>
> > #include <linux/io.h>
> >
> > +#include <asm/mach-types.h>
> > #include <asm/system.h>
> > #include <mach/hardware.h>
> > #include <mach/dma.h>
> > @@ -1110,6 +1111,14 @@ int omap_dma_running(void)
> > {
> > int lch;
> >
> > + /*
> > + * On Amstrad Delta, the OMAP internal LCD controller will start the
> > + * transfer when it gets enabled, so assume DMA running if LCD enabled.
> > + */
> > + if (machine_is_ams_delta())
> > + if (omap_readw(0xfffec000 + 0x00) & (1 << 0))
> > + return 1;
> > +
> > /* Check if LCD DMA is running */
> > if (cpu_is_omap16xx())
> > if (omap_readw(OMAP1610_DMA_LCD_CCR) & OMAP_DMA_CCR_EN)
>
>