Signed-off-by: Guenter Roeck <[email protected]>
---
Documentation/hwmon/jc42 | 86 +++++++
MAINTAINERS | 7 +
drivers/hwmon/Kconfig | 11 +
drivers/hwmon/Makefile | 1 +
drivers/hwmon/jc42.c | 575 ++++++++++++++++++++++++++++++++++++++++++++++
5 files changed, 680 insertions(+), 0 deletions(-)
create mode 100644 Documentation/hwmon/jc42
create mode 100644 drivers/hwmon/jc42.c
diff --git a/Documentation/hwmon/jc42 b/Documentation/hwmon/jc42
new file mode 100644
index 0000000..f7c9701
--- /dev/null
+++ b/Documentation/hwmon/jc42
@@ -0,0 +1,86 @@
+Kernel driver jc42
+==================
+
+Supported chips:
+ * Analog Devices ADT7408
+ Prefix: 'adt7408'
+ Addresses scanned: I2C 0x18 - 0x1f
+ Datasheets:
+ http://www.analog.com/static/imported-files/data_sheets/ADT7408.pdf
+ * NXP Semiconductors SE97, SE97B
+ Prefix: 'se97'
+ Addresses scanned: I2C 0x18 - 0x1f
+ Datasheets:
+ http://www.nxp.com/documents/data_sheet/SE97.pdf
+ http://www.nxp.com/documents/data_sheet/SE97B.pdf
+ * NXP Semiconductors SE98
+ Prefix: 'se98'
+ Addresses scanned: I2C 0x18 - 0x1f
+ Datasheets:
+ http://www.nxp.com/documents/data_sheet/SE98.pdf
+ * Microchip MCP9805, MCP98242, MCP98243, MCP9843
+ Prefixes: 'mcp9805', 'mcp98242', 'mcp98243', 'mcp9843'
+ Addresses scanned: I2C 0x18 - 0x1f
+ Datasheets:
+ http://ww1.microchip.com/downloads/en/DeviceDoc/21977b.pdf
+ http://ww1.microchip.com/downloads/en/DeviceDoc/21996a.pdf
+ http://ww1.microchip.com/downloads/en/DeviceDoc/22153c.pdf
+ * ON Semiconductor CAT34TS02, CAT6095
+ Prefix: 'cat34ts02', 'cat6095'
+ Addresses scanned: I2C 0x18 - 0x1f
+ Datasheet:
+ http://www.onsemi.com/pub_link/Collateral/CAT34TS02-D.PDF
+ http://www.onsemi.com/pub/Collateral/CAT6095-D.PDF
+ * ST Microelectronics STTS424, STTS424E02
+ Prefix: 'stts424'
+ Addresses scanned: I2C 0x18 - 0x1f
+ Datasheets:
+ http://www.st.com/stonline/products/literature/ds/13447/stts424.pdf
+ http://www.st.com/stonline/products/literature/ds/13448/stts424e02.pdf
+ * JEDEC JC 42.4 compliant temperature sensor chips
+ Prefix: 'jc42'
+ Addresses scanned: I2C 0x18 - 0x1f
+ Datasheet: -
+
+Author:
+ Guenter Roeck <[email protected]>
+
+
+Description
+-----------
+
+This driver implements support for JEDEC JC 42.4 compliant temperature sensors.
+The driver auto-detects the chips listed above, but can be manually instantiated
+to support other JC 42.4 compliant chips.
+
+Example: the following will load the driver for a generic JC 42.4 compliant
+temperature sensor at address 0x18 on I2C bus #1:
+
+# modprobe jc42
+# echo jc42 0x18 > /sys/bus/i2c/devices/i2c-1/new_device
+
+A JC 42.4 compliant chip supports a single temperature sensor. Minimum, maximum,
+and critical temperature can be configured. There are alarms for high, low,
+and critical thresholds.
+
+There is also an hysteresis to control the thresholds for resetting alarms.
+Per JC 42.4 specification, the hysteresis threshold can be configured to 0, 1.5,
+3.0, and 6.0 degrees C. Configured hysteresis values will be rounded to those
+limits. The chip supports only a single register to configure the hysteresis,
+which applies to all limits. This register can be written by writing into
+temp1_crit_hyst. Other hysteresis attributes are read-only.
+
+Sysfs entries
+-------------
+
+temp1_input Temperature (RO)
+temp1_min Minimum temperature (RW)
+temp1_max Maximum temperature (RW)
+temp1_crit Critical high temperature (RW)
+
+temp1_crit_hyst Critical hysteresis temperature (RW)
+temp1_max_hyst Maximum hysteresis temperature (RO)
+
+temp1_min_alarm Temperature low alarm
+temp1_max_alarm Temperature high alarm
+temp1_crit_alarm Temperature critical alarm
diff --git a/MAINTAINERS b/MAINTAINERS
index a07a49d..c7e4841 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -3182,6 +3182,13 @@ F: Documentation/video4linux/*.ivtv
F: drivers/media/video/ivtv/
F: include/linux/ivtv*
+JC42.4 TEMPERATURE SENSOR DRIVER
+M: Guenter Roeck <[email protected]>
+L: [email protected]
+S: Maintained
+F: drivers/hwmon/jc42.c
+F: Documentation/hwmon/jc42
+
JFS FILESYSTEM
M: Dave Kleikamp <[email protected]>
L: [email protected]
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index e19cf8e..cf0d99b 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -446,6 +446,17 @@ config SENSORS_IT87
This driver can also be built as a module. If so, the module
will be called it87.
+config SENSORS_JC42
+ tristate "JEDEC JC42.4 compliant temperature sensors"
+ help
+ If you say yes here you get support for Jedec JC42.4 compliant
+ temperature sensors. Support will include, but not be limited to,
+ ADT7408, SE97, SE98, MCP9805, MCP98242, MCP98243, MCP9843, CAT34TS02,
+ CAT6095, and STTS424.
+
+ This driver can also be built as a module. If so, the module
+ will be called jc42.
+
config SENSORS_LM63
tristate "National Semiconductor LM63 and LM64"
depends on I2C
diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
index 2138ceb..6a93615 100644
--- a/drivers/hwmon/Makefile
+++ b/drivers/hwmon/Makefile
@@ -55,6 +55,7 @@ obj-$(CONFIG_SENSORS_I5K_AMB) += i5k_amb.o
obj-$(CONFIG_SENSORS_IBMAEM) += ibmaem.o
obj-$(CONFIG_SENSORS_IBMPEX) += ibmpex.o
obj-$(CONFIG_SENSORS_IT87) += it87.o
+obj-$(CONFIG_SENSORS_JC42) += jc42.o
obj-$(CONFIG_SENSORS_K8TEMP) += k8temp.o
obj-$(CONFIG_SENSORS_K10TEMP) += k10temp.o
obj-$(CONFIG_SENSORS_LIS3LV02D) += lis3lv02d.o hp_accel.o
diff --git a/drivers/hwmon/jc42.c b/drivers/hwmon/jc42.c
new file mode 100644
index 0000000..da146ff
--- /dev/null
+++ b/drivers/hwmon/jc42.c
@@ -0,0 +1,575 @@
+/*
+ * jc42.c - driver for Jedec JC42.4 compliant temperature sensors
+ *
+ * Copyright (c) 2010 Ericsson AB.
+ *
+ * Derived from lm77.c by Andras BALI <[email protected]>.
+ *
+ * JC42.4 compliant temperature sensors are typically used on memory modules.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/jiffies.h>
+#include <linux/i2c.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/err.h>
+#include <linux/mutex.h>
+
+/* Addresses to scan */
+static const unsigned short normal_i2c[] = {
+ 0x18, 0x19, 0x1a, 0x1b, 0x1c, 0x1d, 0x1e, 0x1f, I2C_CLIENT_END };
+
+/* JC42 registers. All registers are 16 bit. */
+#define JC42_REG_CAP 0x00
+#define JC42_REG_CONFIG 0x01
+#define JC42_REG_TEMP_UPPER 0x02
+#define JC42_REG_TEMP_LOWER 0x03
+#define JC42_REG_TEMP_CRITICAL 0x04
+#define JC42_REG_TEMP 0x05
+#define JC42_REG_MANID 0x06
+#define JC42_REG_DEVICEID 0x07
+
+/* Status bits in temperature register */
+#define JC42_ALARM_CRIT_BIT 15
+#define JC42_ALARM_MAX_BIT 14
+#define JC42_ALARM_MIN_BIT 13
+
+/* Configuration register defines */
+#define JC42_CFG_CRIT_ONLY (1 << 2)
+#define JC42_CFG_SHUTDOWN (1 << 8)
+#define JC42_CFG_HYST_SHIFT 9
+#define JC42_CFG_HYST_MASK 0x03
+
+/* Capabilities */
+#define JC42_CAP_RANGE (1 << 2)
+
+/* Supported chips */
+#define SE97_MANID 0x1131
+#define SE97_DEVID 0xa200
+#define SE97_DEVID_MASK 0xfffc
+
+#define SE98_MANID 0x1131
+#define SE98_DEVID 0xa100
+#define SE98_DEVID_MASK 0xfffc
+
+#define STTS424_MANID 0x104a
+#define STTS424_DEVID 0x0101
+#define STTS424_DEVID_MASK 0xffff
+
+#define STTS424E_MANID 0x104a
+#define STTS424E_DEVID 0x0000
+#define STTS424E_DEVID_MASK 0xfffe
+
+#define CAT6095_MANID 0x1b09
+#define CAT6095_DEVID 0x0800 /* Also matches CAT34TS02 */
+#define CAT6095_DEVID_MASK 0xffe0
+
+#define MCP98242_MANID 0x0054
+#define MCP98242_DEVID 0x2000
+#define MCP98242_DEVID_MASK 0xfffc
+
+#define MCP98243_MANID 0x0054
+#define MCP98243_DEVID 0x2100
+#define MCP98243_DEVID_MASK 0xfffc
+
+#define MCP9843_MANID 0x0054
+#define MCP9843_DEVID 0x0000 /* Also matches mcp9805 */
+#define MCP9843_DEVID_MASK 0xfffe
+
+#define ADT7408_MANID 0x11d4
+#define ADT7408_DEVID 0x0801
+#define ADT7408_DEVID_MASK 0xffff
+
+static u16 jc42_hysteresis[] = { 0, 1500, 3000, 6000 };
+
+struct jc42_chips {
+ u16 manid;
+ u16 devid;
+ u16 devid_mask;
+};
+
+static struct jc42_chips jc42_chips[] = {
+ { SE97_MANID, SE97_DEVID, SE97_DEVID_MASK },
+ { SE98_MANID, SE98_DEVID, SE98_DEVID_MASK },
+ { STTS424_MANID, STTS424_DEVID, STTS424_DEVID_MASK },
+ { STTS424E_MANID, STTS424E_DEVID, STTS424E_DEVID_MASK },
+ { CAT6095_MANID, CAT6095_DEVID, CAT6095_DEVID_MASK },
+ { MCP98242_MANID, MCP98242_DEVID, MCP98242_DEVID_MASK },
+ { MCP98243_MANID, MCP98243_DEVID, MCP98243_DEVID_MASK },
+ { MCP9843_MANID, MCP9843_DEVID, MCP9843_DEVID_MASK },
+ { ADT7408_MANID, ADT7408_DEVID, ADT7408_DEVID_MASK },
+};
+
+/* Each client has this additional data */
+struct jc42_data {
+ struct device *hwmon_dev;
+ struct mutex update_lock;
+ bool extended; /* true if extended range supported */
+ bool valid;
+ unsigned long last_updated; /* In jiffies */
+ u16 orig_config; /* original configuration */
+ u16 config; /* configuration */
+ u16 temp_input; /* Temperatures */
+ u16 temp_crit;
+ u16 temp_min;
+ u16 temp_max;
+};
+
+static int jc42_probe(struct i2c_client *client,
+ const struct i2c_device_id *id);
+static int jc42_detect(struct i2c_client *client, struct i2c_board_info *info);
+static int jc42_remove(struct i2c_client *client);
+static int jc42_read_value(struct i2c_client *client, u8 reg);
+static int jc42_write_value(struct i2c_client *client, u8 reg, u16 value);
+
+static struct jc42_data *jc42_update_device(struct device *dev);
+
+static const struct i2c_device_id jc42_id[] = {
+ { "adt7408", 0 },
+ { "cat94ts02", 0 },
+ { "cat6095", 0 },
+ { "jc42", 0 },
+ { "mcp9805", 0 },
+ { "mcp98242", 0 },
+ { "mcp98243", 0 },
+ { "mcp9843", 0 },
+ { "se97", 0 },
+ { "se97b", 0 },
+ { "se98", 0 },
+ { "stts424", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, jc42_id);
+
+#ifdef CONFIG_PM
+
+static int jc42_suspend(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct jc42_data *data = i2c_get_clientdata(client);
+
+ data->config |= JC42_CFG_SHUTDOWN;
+ jc42_write_value(client, JC42_REG_CONFIG, data->config);
+ return 0;
+}
+
+static int jc42_resume(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct jc42_data *data = i2c_get_clientdata(client);
+
+ data->config &= ~JC42_CFG_SHUTDOWN;
+ jc42_write_value(client, JC42_REG_CONFIG, data->config);
+ return 0;
+}
+
+static const struct dev_pm_ops jc42_dev_pm_ops = {
+ .suspend = jc42_suspend,
+ .resume = jc42_resume,
+};
+
+#define JC42_DEV_PM_OPS (&jc42_dev_pm_ops)
+#else
+#define JC42_DEV_PM_OPS NULL
+#endif /* CONFIG_PM */
+
+/* This is the driver that will be inserted */
+static struct i2c_driver jc42_driver = {
+ .class = I2C_CLASS_HWMON,
+ .driver = {
+ .name = "jc42",
+ .pm = JC42_DEV_PM_OPS,
+ },
+ .probe = jc42_probe,
+ .remove = jc42_remove,
+ .id_table = jc42_id,
+ .detect = jc42_detect,
+ .address_list = normal_i2c,
+};
+
+#define JC42_TEMP_MIN_EXTENDED (-40000)
+#define JC42_TEMP_MIN 0
+#define JC42_TEMP_MAX 125000
+
+static u16 jc42_temp_to_reg(int temp, bool extended)
+{
+ int ntemp = SENSORS_LIMIT(temp,
+ extended ? JC42_TEMP_MIN_EXTENDED :
+ JC42_TEMP_MIN, JC42_TEMP_MAX);
+
+ /* convert from 0.001 to 0.0625 resolution */
+ return (ntemp * 2 / 125) & 0x1fff;
+}
+
+static int jc42_temp_from_reg(s16 reg)
+{
+ reg &= 0x1fff;
+
+ /* sign extend register */
+ if (reg & 0x1000)
+ reg |= 0xf000;
+
+ /* convert from 0.0625 to 0.001 resolution */
+ return reg * 125 / 2;
+}
+
+/* sysfs stuff */
+
+/* read routines for temperature limits */
+#define show(value) \
+static ssize_t show_##value(struct device *dev, \
+ struct device_attribute *attr, \
+ char *buf) \
+{ \
+ struct jc42_data *data = jc42_update_device(dev); \
+ if (IS_ERR(data)) \
+ return PTR_ERR(data); \
+ return sprintf(buf, "%d\n", jc42_temp_from_reg(data->value)); \
+}
+
+show(temp_input);
+show(temp_crit);
+show(temp_min);
+show(temp_max);
+
+/* read routines for hysteresis values */
+static ssize_t show_temp_crit_hyst(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct jc42_data *data = jc42_update_device(dev);
+ int temp, hyst;
+
+ if (IS_ERR(data))
+ return PTR_ERR(data);
+
+ temp = jc42_temp_from_reg(data->temp_crit);
+ hyst = jc42_hysteresis[(data->config >> JC42_CFG_HYST_SHIFT)
+ & JC42_CFG_HYST_MASK];
+ return sprintf(buf, "%d\n", temp - hyst);
+}
+
+static ssize_t show_temp_max_hyst(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct jc42_data *data = jc42_update_device(dev);
+ int temp, hyst;
+
+ if (IS_ERR(data))
+ return PTR_ERR(data);
+
+ temp = jc42_temp_from_reg(data->temp_max);
+ hyst = jc42_hysteresis[(data->config >> JC42_CFG_HYST_SHIFT)
+ & JC42_CFG_HYST_MASK];
+ return sprintf(buf, "%d\n", temp - hyst);
+}
+
+/* write routines */
+#define set(value, reg) \
+static ssize_t set_##value(struct device *dev, \
+ struct device_attribute *attr, \
+ const char *buf, size_t count) \
+{ \
+ struct i2c_client *client = to_i2c_client(dev); \
+ struct jc42_data *data = i2c_get_clientdata(client); \
+ int err, ret = count; \
+ long val; \
+ if (strict_strtol(buf, 10, &val) < 0) \
+ return -EINVAL; \
+ mutex_lock(&data->update_lock); \
+ data->value = jc42_temp_to_reg(val, data->extended); \
+ err = jc42_write_value(client, reg, data->value); \
+ if (err < 0) \
+ ret = err; \
+ mutex_unlock(&data->update_lock); \
+ return ret; \
+}
+
+set(temp_min, JC42_REG_TEMP_LOWER);
+set(temp_max, JC42_REG_TEMP_UPPER);
+set(temp_crit, JC42_REG_TEMP_CRITICAL);
+
+/* JC42.4 compliant chips only support four hysteresis values.
+ * Pick best choice and go from there. */
+static ssize_t set_temp_crit_hyst(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct jc42_data *data = i2c_get_clientdata(client);
+ long val;
+ int diff, hyst;
+ int err;
+ int ret = count;
+
+ if (strict_strtoul(buf, 10, &val) < 0)
+ return -EINVAL;
+
+ diff = jc42_temp_from_reg(data->temp_crit) - val;
+ hyst = 0;
+ if (diff > 0) {
+ if (diff < 2250)
+ hyst = 1; /* 1.5 degrees C */
+ else if (diff < 4500)
+ hyst = 2; /* 3.0 degrees C */
+ else
+ hyst = 3; /* 6.0 degrees C */
+ }
+
+ mutex_lock(&data->update_lock);
+ data->config = (data->config
+ & ~(JC42_CFG_HYST_MASK << JC42_CFG_HYST_SHIFT))
+ | (hyst << JC42_CFG_HYST_SHIFT);
+ err = jc42_write_value(client, JC42_REG_CONFIG, data->config);
+ if (err < 0)
+ ret = err;
+ mutex_unlock(&data->update_lock);
+ return ret;
+}
+
+static ssize_t show_alarm(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ u16 bit = to_sensor_dev_attr(attr)->index;
+ struct jc42_data *data = jc42_update_device(dev);
+ u16 val;
+
+ if (IS_ERR(data))
+ return PTR_ERR(data);
+
+ val = data->temp_input;
+ if (bit != JC42_ALARM_CRIT_BIT && (data->config & JC42_CFG_CRIT_ONLY))
+ val = 0;
+ return sprintf(buf, "%u\n", (val >> bit) & 1);
+}
+
+static DEVICE_ATTR(temp1_input, S_IRUGO,
+ show_temp_input, NULL);
+static DEVICE_ATTR(temp1_crit, S_IWUSR | S_IRUGO,
+ show_temp_crit, set_temp_crit);
+static DEVICE_ATTR(temp1_min, S_IWUSR | S_IRUGO,
+ show_temp_min, set_temp_min);
+static DEVICE_ATTR(temp1_max, S_IWUSR | S_IRUGO,
+ show_temp_max, set_temp_max);
+
+static DEVICE_ATTR(temp1_crit_hyst, S_IWUSR | S_IRUGO,
+ show_temp_crit_hyst, set_temp_crit_hyst);
+static DEVICE_ATTR(temp1_max_hyst, S_IRUGO,
+ show_temp_max_hyst, NULL);
+
+static SENSOR_DEVICE_ATTR(temp1_crit_alarm, S_IRUGO, show_alarm, NULL,
+ JC42_ALARM_CRIT_BIT);
+static SENSOR_DEVICE_ATTR(temp1_min_alarm, S_IRUGO, show_alarm, NULL,
+ JC42_ALARM_MIN_BIT);
+static SENSOR_DEVICE_ATTR(temp1_max_alarm, S_IRUGO, show_alarm, NULL,
+ JC42_ALARM_MAX_BIT);
+
+static struct attribute *jc42_attributes[] = {
+ &dev_attr_temp1_input.attr,
+ &dev_attr_temp1_crit.attr,
+ &dev_attr_temp1_min.attr,
+ &dev_attr_temp1_max.attr,
+ &dev_attr_temp1_crit_hyst.attr,
+ &dev_attr_temp1_max_hyst.attr,
+ &sensor_dev_attr_temp1_crit_alarm.dev_attr.attr,
+ &sensor_dev_attr_temp1_min_alarm.dev_attr.attr,
+ &sensor_dev_attr_temp1_max_alarm.dev_attr.attr,
+ NULL
+};
+
+static const struct attribute_group jc42_group = {
+ .attrs = jc42_attributes,
+};
+
+/* Return 0 if detection is successful, -ENODEV otherwise */
+static int jc42_detect(struct i2c_client *new_client,
+ struct i2c_board_info *info)
+{
+ struct i2c_adapter *adapter = new_client->adapter;
+ int i, config, cap, manid, devid;
+
+ if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA |
+ I2C_FUNC_SMBUS_WORD_DATA))
+ return -ENODEV;
+
+ cap = jc42_read_value(new_client, JC42_REG_CAP);
+ config = jc42_read_value(new_client, JC42_REG_CONFIG);
+ manid = jc42_read_value(new_client, JC42_REG_MANID);
+ devid = jc42_read_value(new_client, JC42_REG_DEVICEID);
+
+ if (cap < 0 || config < 0 || manid < 0 || devid < 0)
+ return -ENODEV;
+
+ if ((cap & 0xff00) || (config & 0xf800))
+ return -ENODEV;
+
+ for (i = 0; i < ARRAY_SIZE(jc42_chips); i++) {
+ if (manid == jc42_chips[i].manid
+ && (devid & jc42_chips[i].devid_mask) ==
+ jc42_chips[i].devid) {
+ strlcpy(info->type, "jc42", I2C_NAME_SIZE);
+ return 0;
+ }
+ }
+ return -ENODEV;
+}
+
+static int jc42_probe(struct i2c_client *new_client,
+ const struct i2c_device_id *id)
+{
+ struct jc42_data *data;
+ int config, cap, err;
+
+ data = kzalloc(sizeof(struct jc42_data), GFP_KERNEL);
+ if (!data) {
+ err = -ENOMEM;
+ goto exit;
+ }
+
+ i2c_set_clientdata(new_client, data);
+ data->valid = false;
+ mutex_init(&data->update_lock);
+
+ cap = jc42_read_value(new_client, JC42_REG_CAP);
+ if (cap < 0) {
+ err = -EINVAL;
+ goto exit_free;
+ }
+ data->extended = !!(cap & JC42_CAP_RANGE);
+
+ config = jc42_read_value(new_client, JC42_REG_CONFIG);
+ if (config < 0) {
+ err = -EINVAL;
+ goto exit_free;
+ }
+ data->orig_config = config;
+ if (config & JC42_CFG_SHUTDOWN) {
+ config &= ~JC42_CFG_SHUTDOWN;
+ jc42_write_value(new_client, JC42_REG_CONFIG, config);
+ }
+ data->config = config;
+
+ /* Register sysfs hooks */
+ err = sysfs_create_group(&new_client->dev.kobj, &jc42_group);
+ if (err)
+ goto exit_free;
+
+ data->hwmon_dev = hwmon_device_register(&new_client->dev);
+ if (IS_ERR(data->hwmon_dev)) {
+ err = PTR_ERR(data->hwmon_dev);
+ goto exit_remove;
+ }
+
+ return 0;
+
+exit_remove:
+ sysfs_remove_group(&new_client->dev.kobj, &jc42_group);
+exit_free:
+ kfree(data);
+exit:
+ return err;
+}
+
+static int jc42_remove(struct i2c_client *client)
+{
+ struct jc42_data *data = i2c_get_clientdata(client);
+ hwmon_device_unregister(data->hwmon_dev);
+ sysfs_remove_group(&client->dev.kobj, &jc42_group);
+ if (data->config != data->orig_config)
+ jc42_write_value(client, JC42_REG_CONFIG, data->orig_config);
+ kfree(data);
+ return 0;
+}
+
+/* All registers are word-sized. */
+static int jc42_read_value(struct i2c_client *client, u8 reg)
+{
+ int ret = i2c_smbus_read_word_data(client, reg);
+ if (ret < 0)
+ return ret;
+ return swab16(ret);
+}
+
+static int jc42_write_value(struct i2c_client *client, u8 reg, u16 value)
+{
+ return i2c_smbus_write_word_data(client, reg, swab16(value));
+}
+
+static struct jc42_data *jc42_update_device(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct jc42_data *data = i2c_get_clientdata(client);
+ struct jc42_data *ret = data;
+ int val;
+
+ mutex_lock(&data->update_lock);
+
+ if (time_after(jiffies, data->last_updated + HZ) || !data->valid) {
+ val = jc42_read_value(client, JC42_REG_TEMP);
+ if (val < 0) {
+ ret = ERR_PTR(val);
+ goto abort;
+ }
+ data->temp_input = val;
+
+ val = jc42_read_value(client, JC42_REG_TEMP_CRITICAL);
+ if (val < 0) {
+ ret = ERR_PTR(val);
+ goto abort;
+ }
+ data->temp_crit = val;
+
+ val = jc42_read_value(client, JC42_REG_TEMP_LOWER);
+ if (val < 0) {
+ ret = ERR_PTR(val);
+ goto abort;
+ }
+ data->temp_min = val;
+
+ val = jc42_read_value(client, JC42_REG_TEMP_UPPER);
+ if (val < 0) {
+ ret = ERR_PTR(val);
+ goto abort;
+ }
+ data->temp_max = val;
+
+ data->last_updated = jiffies;
+ data->valid = true;
+ }
+abort:
+ mutex_unlock(&data->update_lock);
+ return ret;
+}
+
+static int __init sensors_jc42_init(void)
+{
+ return i2c_add_driver(&jc42_driver);
+}
+
+static void __exit sensors_jc42_exit(void)
+{
+ i2c_del_driver(&jc42_driver);
+}
+
+MODULE_AUTHOR("Guenter Roeck <[email protected]>");
+MODULE_DESCRIPTION("JC42 driver");
+MODULE_LICENSE("GPL");
+
+module_init(sensors_jc42_init);
+module_exit(sensors_jc42_exit);
--
1.7.0.87.g0901d
On Thu, Jul 08, 2010 at 11:28:07AM -0400, Paul Goyette wrote:
>
> You might want to include the MAXIM 6604 chip as well. This has been
> part of my initial NetBSD sdtemp(4) driver since I wrote it...
>
> #define MAXIM_MANUFACTURER_ID 0x004D
> #define MAX_6604_DEVICE_ID 0x3E00
> #define MAX_6604_MASK 0xFFFF
>
Sure, will do. Also, good idea to use only one define per manufacturer -
I'll update the other defines to reflect that.
Guenter
>
> On Thu, 8 Jul 2010, Guenter Roeck wrote:
>
> > Signed-off-by: Guenter Roeck <[email protected]>
> > ---
> > Documentation/hwmon/jc42 | 86 +++++++
> > MAINTAINERS | 7 +
> > drivers/hwmon/Kconfig | 11 +
> > drivers/hwmon/Makefile | 1 +
> > drivers/hwmon/jc42.c | 575 ++++++++++++++++++++++++++++++++++++++++++++++
> > 5 files changed, 680 insertions(+), 0 deletions(-)
> > create mode 100644 Documentation/hwmon/jc42
> > create mode 100644 drivers/hwmon/jc42.c
> >
> > diff --git a/Documentation/hwmon/jc42 b/Documentation/hwmon/jc42
> > new file mode 100644
> > index 0000000..f7c9701
> > --- /dev/null
> > +++ b/Documentation/hwmon/jc42
> > @@ -0,0 +1,86 @@
> > +Kernel driver jc42
> > +==================
> > +
> > +Supported chips:
> > + * Analog Devices ADT7408
> > + Prefix: 'adt7408'
> > + Addresses scanned: I2C 0x18 - 0x1f
> > + Datasheets:
> > + http://www.analog.com/static/imported-files/data_sheets/ADT7408.pdf
> > + * NXP Semiconductors SE97, SE97B
> > + Prefix: 'se97'
> > + Addresses scanned: I2C 0x18 - 0x1f
> > + Datasheets:
> > + http://www.nxp.com/documents/data_sheet/SE97.pdf
> > + http://www.nxp.com/documents/data_sheet/SE97B.pdf
> > + * NXP Semiconductors SE98
> > + Prefix: 'se98'
> > + Addresses scanned: I2C 0x18 - 0x1f
> > + Datasheets:
> > + http://www.nxp.com/documents/data_sheet/SE98.pdf
> > + * Microchip MCP9805, MCP98242, MCP98243, MCP9843
> > + Prefixes: 'mcp9805', 'mcp98242', 'mcp98243', 'mcp9843'
> > + Addresses scanned: I2C 0x18 - 0x1f
> > + Datasheets:
> > + http://ww1.microchip.com/downloads/en/DeviceDoc/21977b.pdf
> > + http://ww1.microchip.com/downloads/en/DeviceDoc/21996a.pdf
> > + http://ww1.microchip.com/downloads/en/DeviceDoc/22153c.pdf
> > + * ON Semiconductor CAT34TS02, CAT6095
> > + Prefix: 'cat34ts02', 'cat6095'
> > + Addresses scanned: I2C 0x18 - 0x1f
> > + Datasheet:
> > + http://www.onsemi.com/pub_link/Collateral/CAT34TS02-D.PDF
> > + http://www.onsemi.com/pub/Collateral/CAT6095-D.PDF
> > + * ST Microelectronics STTS424, STTS424E02
> > + Prefix: 'stts424'
> > + Addresses scanned: I2C 0x18 - 0x1f
> > + Datasheets:
> > + http://www.st.com/stonline/products/literature/ds/13447/stts424.pdf
> > + http://www.st.com/stonline/products/literature/ds/13448/stts424e02.pdf
> > + * JEDEC JC 42.4 compliant temperature sensor chips
> > + Prefix: 'jc42'
> > + Addresses scanned: I2C 0x18 - 0x1f
> > + Datasheet: -
> > +
> > +Author:
> > + Guenter Roeck <[email protected]>
> > +
> > +
> > +Description
> > +-----------
> > +
> > +This driver implements support for JEDEC JC 42.4 compliant temperature sensors.
> > +The driver auto-detects the chips listed above, but can be manually instantiated
> > +to support other JC 42.4 compliant chips.
> > +
> > +Example: the following will load the driver for a generic JC 42.4 compliant
> > +temperature sensor at address 0x18 on I2C bus #1:
> > +
> > +# modprobe jc42
> > +# echo jc42 0x18 > /sys/bus/i2c/devices/i2c-1/new_device
> > +
> > +A JC 42.4 compliant chip supports a single temperature sensor. Minimum, maximum,
> > +and critical temperature can be configured. There are alarms for high, low,
> > +and critical thresholds.
> > +
> > +There is also an hysteresis to control the thresholds for resetting alarms.
> > +Per JC 42.4 specification, the hysteresis threshold can be configured to 0, 1.5,
> > +3.0, and 6.0 degrees C. Configured hysteresis values will be rounded to those
> > +limits. The chip supports only a single register to configure the hysteresis,
> > +which applies to all limits. This register can be written by writing into
> > +temp1_crit_hyst. Other hysteresis attributes are read-only.
> > +
> > +Sysfs entries
> > +-------------
> > +
> > +temp1_input Temperature (RO)
> > +temp1_min Minimum temperature (RW)
> > +temp1_max Maximum temperature (RW)
> > +temp1_crit Critical high temperature (RW)
> > +
> > +temp1_crit_hyst Critical hysteresis temperature (RW)
> > +temp1_max_hyst Maximum hysteresis temperature (RO)
> > +
> > +temp1_min_alarm Temperature low alarm
> > +temp1_max_alarm Temperature high alarm
> > +temp1_crit_alarm Temperature critical alarm
> > diff --git a/MAINTAINERS b/MAINTAINERS
> > index a07a49d..c7e4841 100644
> > --- a/MAINTAINERS
> > +++ b/MAINTAINERS
> > @@ -3182,6 +3182,13 @@ F: Documentation/video4linux/*.ivtv
> > F: drivers/media/video/ivtv/
> > F: include/linux/ivtv*
> >
> > +JC42.4 TEMPERATURE SENSOR DRIVER
> > +M: Guenter Roeck <[email protected]>
> > +L: [email protected]
> > +S: Maintained
> > +F: drivers/hwmon/jc42.c
> > +F: Documentation/hwmon/jc42
> > +
> > JFS FILESYSTEM
> > M: Dave Kleikamp <[email protected]>
> > L: [email protected]
> > diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
> > index e19cf8e..cf0d99b 100644
> > --- a/drivers/hwmon/Kconfig
> > +++ b/drivers/hwmon/Kconfig
> > @@ -446,6 +446,17 @@ config SENSORS_IT87
> > This driver can also be built as a module. If so, the module
> > will be called it87.
> >
> > +config SENSORS_JC42
> > + tristate "JEDEC JC42.4 compliant temperature sensors"
> > + help
> > + If you say yes here you get support for Jedec JC42.4 compliant
> > + temperature sensors. Support will include, but not be limited to,
> > + ADT7408, SE97, SE98, MCP9805, MCP98242, MCP98243, MCP9843, CAT34TS02,
> > + CAT6095, and STTS424.
> > +
> > + This driver can also be built as a module. If so, the module
> > + will be called jc42.
> > +
> > config SENSORS_LM63
> > tristate "National Semiconductor LM63 and LM64"
> > depends on I2C
> > diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
> > index 2138ceb..6a93615 100644
> > --- a/drivers/hwmon/Makefile
> > +++ b/drivers/hwmon/Makefile
> > @@ -55,6 +55,7 @@ obj-$(CONFIG_SENSORS_I5K_AMB) += i5k_amb.o
> > obj-$(CONFIG_SENSORS_IBMAEM) += ibmaem.o
> > obj-$(CONFIG_SENSORS_IBMPEX) += ibmpex.o
> > obj-$(CONFIG_SENSORS_IT87) += it87.o
> > +obj-$(CONFIG_SENSORS_JC42) += jc42.o
> > obj-$(CONFIG_SENSORS_K8TEMP) += k8temp.o
> > obj-$(CONFIG_SENSORS_K10TEMP) += k10temp.o
> > obj-$(CONFIG_SENSORS_LIS3LV02D) += lis3lv02d.o hp_accel.o
> > diff --git a/drivers/hwmon/jc42.c b/drivers/hwmon/jc42.c
> > new file mode 100644
> > index 0000000..da146ff
> > --- /dev/null
> > +++ b/drivers/hwmon/jc42.c
> > @@ -0,0 +1,575 @@
> > +/*
> > + * jc42.c - driver for Jedec JC42.4 compliant temperature sensors
> > + *
> > + * Copyright (c) 2010 Ericsson AB.
> > + *
> > + * Derived from lm77.c by Andras BALI <[email protected]>.
> > + *
> > + * JC42.4 compliant temperature sensors are typically used on memory modules.
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License as published by
> > + * the Free Software Foundation; either version 2 of the License, or
> > + * (at your option) any later version.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > + * GNU General Public License for more details.
> > + *
> > + * You should have received a copy of the GNU General Public License
> > + * along with this program; if not, write to the Free Software
> > + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
> > + */
> > +
> > +#include <linux/module.h>
> > +#include <linux/init.h>
> > +#include <linux/slab.h>
> > +#include <linux/jiffies.h>
> > +#include <linux/i2c.h>
> > +#include <linux/hwmon.h>
> > +#include <linux/hwmon-sysfs.h>
> > +#include <linux/err.h>
> > +#include <linux/mutex.h>
> > +
> > +/* Addresses to scan */
> > +static const unsigned short normal_i2c[] = {
> > + 0x18, 0x19, 0x1a, 0x1b, 0x1c, 0x1d, 0x1e, 0x1f, I2C_CLIENT_END };
> > +
> > +/* JC42 registers. All registers are 16 bit. */
> > +#define JC42_REG_CAP 0x00
> > +#define JC42_REG_CONFIG 0x01
> > +#define JC42_REG_TEMP_UPPER 0x02
> > +#define JC42_REG_TEMP_LOWER 0x03
> > +#define JC42_REG_TEMP_CRITICAL 0x04
> > +#define JC42_REG_TEMP 0x05
> > +#define JC42_REG_MANID 0x06
> > +#define JC42_REG_DEVICEID 0x07
> > +
> > +/* Status bits in temperature register */
> > +#define JC42_ALARM_CRIT_BIT 15
> > +#define JC42_ALARM_MAX_BIT 14
> > +#define JC42_ALARM_MIN_BIT 13
> > +
> > +/* Configuration register defines */
> > +#define JC42_CFG_CRIT_ONLY (1 << 2)
> > +#define JC42_CFG_SHUTDOWN (1 << 8)
> > +#define JC42_CFG_HYST_SHIFT 9
> > +#define JC42_CFG_HYST_MASK 0x03
> > +
> > +/* Capabilities */
> > +#define JC42_CAP_RANGE (1 << 2)
> > +
> > +/* Supported chips */
> > +#define SE97_MANID 0x1131
> > +#define SE97_DEVID 0xa200
> > +#define SE97_DEVID_MASK 0xfffc
> > +
> > +#define SE98_MANID 0x1131
> > +#define SE98_DEVID 0xa100
> > +#define SE98_DEVID_MASK 0xfffc
> > +
> > +#define STTS424_MANID 0x104a
> > +#define STTS424_DEVID 0x0101
> > +#define STTS424_DEVID_MASK 0xffff
> > +
> > +#define STTS424E_MANID 0x104a
> > +#define STTS424E_DEVID 0x0000
> > +#define STTS424E_DEVID_MASK 0xfffe
> > +
> > +#define CAT6095_MANID 0x1b09
> > +#define CAT6095_DEVID 0x0800 /* Also matches CAT34TS02 */
> > +#define CAT6095_DEVID_MASK 0xffe0
> > +
> > +#define MCP98242_MANID 0x0054
> > +#define MCP98242_DEVID 0x2000
> > +#define MCP98242_DEVID_MASK 0xfffc
> > +
> > +#define MCP98243_MANID 0x0054
> > +#define MCP98243_DEVID 0x2100
> > +#define MCP98243_DEVID_MASK 0xfffc
> > +
> > +#define MCP9843_MANID 0x0054
> > +#define MCP9843_DEVID 0x0000 /* Also matches mcp9805 */
> > +#define MCP9843_DEVID_MASK 0xfffe
> > +
> > +#define ADT7408_MANID 0x11d4
> > +#define ADT7408_DEVID 0x0801
> > +#define ADT7408_DEVID_MASK 0xffff
> > +
> > +static u16 jc42_hysteresis[] = { 0, 1500, 3000, 6000 };
> > +
> > +struct jc42_chips {
> > + u16 manid;
> > + u16 devid;
> > + u16 devid_mask;
> > +};
> > +
> > +static struct jc42_chips jc42_chips[] = {
> > + { SE97_MANID, SE97_DEVID, SE97_DEVID_MASK },
> > + { SE98_MANID, SE98_DEVID, SE98_DEVID_MASK },
> > + { STTS424_MANID, STTS424_DEVID, STTS424_DEVID_MASK },
> > + { STTS424E_MANID, STTS424E_DEVID, STTS424E_DEVID_MASK },
> > + { CAT6095_MANID, CAT6095_DEVID, CAT6095_DEVID_MASK },
> > + { MCP98242_MANID, MCP98242_DEVID, MCP98242_DEVID_MASK },
> > + { MCP98243_MANID, MCP98243_DEVID, MCP98243_DEVID_MASK },
> > + { MCP9843_MANID, MCP9843_DEVID, MCP9843_DEVID_MASK },
> > + { ADT7408_MANID, ADT7408_DEVID, ADT7408_DEVID_MASK },
> > +};
> > +
> > +/* Each client has this additional data */
> > +struct jc42_data {
> > + struct device *hwmon_dev;
> > + struct mutex update_lock;
> > + bool extended; /* true if extended range supported */
> > + bool valid;
> > + unsigned long last_updated; /* In jiffies */
> > + u16 orig_config; /* original configuration */
> > + u16 config; /* configuration */
> > + u16 temp_input; /* Temperatures */
> > + u16 temp_crit;
> > + u16 temp_min;
> > + u16 temp_max;
> > +};
> > +
> > +static int jc42_probe(struct i2c_client *client,
> > + const struct i2c_device_id *id);
> > +static int jc42_detect(struct i2c_client *client, struct i2c_board_info *info);
> > +static int jc42_remove(struct i2c_client *client);
> > +static int jc42_read_value(struct i2c_client *client, u8 reg);
> > +static int jc42_write_value(struct i2c_client *client, u8 reg, u16 value);
> > +
> > +static struct jc42_data *jc42_update_device(struct device *dev);
> > +
> > +static const struct i2c_device_id jc42_id[] = {
> > + { "adt7408", 0 },
> > + { "cat94ts02", 0 },
> > + { "cat6095", 0 },
> > + { "jc42", 0 },
> > + { "mcp9805", 0 },
> > + { "mcp98242", 0 },
> > + { "mcp98243", 0 },
> > + { "mcp9843", 0 },
> > + { "se97", 0 },
> > + { "se97b", 0 },
> > + { "se98", 0 },
> > + { "stts424", 0 },
> > + { }
> > +};
> > +MODULE_DEVICE_TABLE(i2c, jc42_id);
> > +
> > +#ifdef CONFIG_PM
> > +
> > +static int jc42_suspend(struct device *dev)
> > +{
> > + struct i2c_client *client = to_i2c_client(dev);
> > + struct jc42_data *data = i2c_get_clientdata(client);
> > +
> > + data->config |= JC42_CFG_SHUTDOWN;
> > + jc42_write_value(client, JC42_REG_CONFIG, data->config);
> > + return 0;
> > +}
> > +
> > +static int jc42_resume(struct device *dev)
> > +{
> > + struct i2c_client *client = to_i2c_client(dev);
> > + struct jc42_data *data = i2c_get_clientdata(client);
> > +
> > + data->config &= ~JC42_CFG_SHUTDOWN;
> > + jc42_write_value(client, JC42_REG_CONFIG, data->config);
> > + return 0;
> > +}
> > +
> > +static const struct dev_pm_ops jc42_dev_pm_ops = {
> > + .suspend = jc42_suspend,
> > + .resume = jc42_resume,
> > +};
> > +
> > +#define JC42_DEV_PM_OPS (&jc42_dev_pm_ops)
> > +#else
> > +#define JC42_DEV_PM_OPS NULL
> > +#endif /* CONFIG_PM */
> > +
> > +/* This is the driver that will be inserted */
> > +static struct i2c_driver jc42_driver = {
> > + .class = I2C_CLASS_HWMON,
> > + .driver = {
> > + .name = "jc42",
> > + .pm = JC42_DEV_PM_OPS,
> > + },
> > + .probe = jc42_probe,
> > + .remove = jc42_remove,
> > + .id_table = jc42_id,
> > + .detect = jc42_detect,
> > + .address_list = normal_i2c,
> > +};
> > +
> > +#define JC42_TEMP_MIN_EXTENDED (-40000)
> > +#define JC42_TEMP_MIN 0
> > +#define JC42_TEMP_MAX 125000
> > +
> > +static u16 jc42_temp_to_reg(int temp, bool extended)
> > +{
> > + int ntemp = SENSORS_LIMIT(temp,
> > + extended ? JC42_TEMP_MIN_EXTENDED :
> > + JC42_TEMP_MIN, JC42_TEMP_MAX);
> > +
> > + /* convert from 0.001 to 0.0625 resolution */
> > + return (ntemp * 2 / 125) & 0x1fff;
> > +}
> > +
> > +static int jc42_temp_from_reg(s16 reg)
> > +{
> > + reg &= 0x1fff;
> > +
> > + /* sign extend register */
> > + if (reg & 0x1000)
> > + reg |= 0xf000;
> > +
> > + /* convert from 0.0625 to 0.001 resolution */
> > + return reg * 125 / 2;
> > +}
> > +
> > +/* sysfs stuff */
> > +
> > +/* read routines for temperature limits */
> > +#define show(value) \
> > +static ssize_t show_##value(struct device *dev, \
> > + struct device_attribute *attr, \
> > + char *buf) \
> > +{ \
> > + struct jc42_data *data = jc42_update_device(dev); \
> > + if (IS_ERR(data)) \
> > + return PTR_ERR(data); \
> > + return sprintf(buf, "%d\n", jc42_temp_from_reg(data->value)); \
> > +}
> > +
> > +show(temp_input);
> > +show(temp_crit);
> > +show(temp_min);
> > +show(temp_max);
> > +
> > +/* read routines for hysteresis values */
> > +static ssize_t show_temp_crit_hyst(struct device *dev,
> > + struct device_attribute *attr, char *buf)
> > +{
> > + struct jc42_data *data = jc42_update_device(dev);
> > + int temp, hyst;
> > +
> > + if (IS_ERR(data))
> > + return PTR_ERR(data);
> > +
> > + temp = jc42_temp_from_reg(data->temp_crit);
> > + hyst = jc42_hysteresis[(data->config >> JC42_CFG_HYST_SHIFT)
> > + & JC42_CFG_HYST_MASK];
> > + return sprintf(buf, "%d\n", temp - hyst);
> > +}
> > +
> > +static ssize_t show_temp_max_hyst(struct device *dev,
> > + struct device_attribute *attr, char *buf)
> > +{
> > + struct jc42_data *data = jc42_update_device(dev);
> > + int temp, hyst;
> > +
> > + if (IS_ERR(data))
> > + return PTR_ERR(data);
> > +
> > + temp = jc42_temp_from_reg(data->temp_max);
> > + hyst = jc42_hysteresis[(data->config >> JC42_CFG_HYST_SHIFT)
> > + & JC42_CFG_HYST_MASK];
> > + return sprintf(buf, "%d\n", temp - hyst);
> > +}
> > +
> > +/* write routines */
> > +#define set(value, reg) \
> > +static ssize_t set_##value(struct device *dev, \
> > + struct device_attribute *attr, \
> > + const char *buf, size_t count) \
> > +{ \
> > + struct i2c_client *client = to_i2c_client(dev); \
> > + struct jc42_data *data = i2c_get_clientdata(client); \
> > + int err, ret = count; \
> > + long val; \
> > + if (strict_strtol(buf, 10, &val) < 0) \
> > + return -EINVAL; \
> > + mutex_lock(&data->update_lock); \
> > + data->value = jc42_temp_to_reg(val, data->extended); \
> > + err = jc42_write_value(client, reg, data->value); \
> > + if (err < 0) \
> > + ret = err; \
> > + mutex_unlock(&data->update_lock); \
> > + return ret; \
> > +}
> > +
> > +set(temp_min, JC42_REG_TEMP_LOWER);
> > +set(temp_max, JC42_REG_TEMP_UPPER);
> > +set(temp_crit, JC42_REG_TEMP_CRITICAL);
> > +
> > +/* JC42.4 compliant chips only support four hysteresis values.
> > + * Pick best choice and go from there. */
> > +static ssize_t set_temp_crit_hyst(struct device *dev,
> > + struct device_attribute *attr,
> > + const char *buf, size_t count)
> > +{
> > + struct i2c_client *client = to_i2c_client(dev);
> > + struct jc42_data *data = i2c_get_clientdata(client);
> > + long val;
> > + int diff, hyst;
> > + int err;
> > + int ret = count;
> > +
> > + if (strict_strtoul(buf, 10, &val) < 0)
> > + return -EINVAL;
> > +
> > + diff = jc42_temp_from_reg(data->temp_crit) - val;
> > + hyst = 0;
> > + if (diff > 0) {
> > + if (diff < 2250)
> > + hyst = 1; /* 1.5 degrees C */
> > + else if (diff < 4500)
> > + hyst = 2; /* 3.0 degrees C */
> > + else
> > + hyst = 3; /* 6.0 degrees C */
> > + }
> > +
> > + mutex_lock(&data->update_lock);
> > + data->config = (data->config
> > + & ~(JC42_CFG_HYST_MASK << JC42_CFG_HYST_SHIFT))
> > + | (hyst << JC42_CFG_HYST_SHIFT);
> > + err = jc42_write_value(client, JC42_REG_CONFIG, data->config);
> > + if (err < 0)
> > + ret = err;
> > + mutex_unlock(&data->update_lock);
> > + return ret;
> > +}
> > +
> > +static ssize_t show_alarm(struct device *dev,
> > + struct device_attribute *attr, char *buf)
> > +{
> > + u16 bit = to_sensor_dev_attr(attr)->index;
> > + struct jc42_data *data = jc42_update_device(dev);
> > + u16 val;
> > +
> > + if (IS_ERR(data))
> > + return PTR_ERR(data);
> > +
> > + val = data->temp_input;
> > + if (bit != JC42_ALARM_CRIT_BIT && (data->config & JC42_CFG_CRIT_ONLY))
> > + val = 0;
> > + return sprintf(buf, "%u\n", (val >> bit) & 1);
> > +}
> > +
> > +static DEVICE_ATTR(temp1_input, S_IRUGO,
> > + show_temp_input, NULL);
> > +static DEVICE_ATTR(temp1_crit, S_IWUSR | S_IRUGO,
> > + show_temp_crit, set_temp_crit);
> > +static DEVICE_ATTR(temp1_min, S_IWUSR | S_IRUGO,
> > + show_temp_min, set_temp_min);
> > +static DEVICE_ATTR(temp1_max, S_IWUSR | S_IRUGO,
> > + show_temp_max, set_temp_max);
> > +
> > +static DEVICE_ATTR(temp1_crit_hyst, S_IWUSR | S_IRUGO,
> > + show_temp_crit_hyst, set_temp_crit_hyst);
> > +static DEVICE_ATTR(temp1_max_hyst, S_IRUGO,
> > + show_temp_max_hyst, NULL);
> > +
> > +static SENSOR_DEVICE_ATTR(temp1_crit_alarm, S_IRUGO, show_alarm, NULL,
> > + JC42_ALARM_CRIT_BIT);
> > +static SENSOR_DEVICE_ATTR(temp1_min_alarm, S_IRUGO, show_alarm, NULL,
> > + JC42_ALARM_MIN_BIT);
> > +static SENSOR_DEVICE_ATTR(temp1_max_alarm, S_IRUGO, show_alarm, NULL,
> > + JC42_ALARM_MAX_BIT);
> > +
> > +static struct attribute *jc42_attributes[] = {
> > + &dev_attr_temp1_input.attr,
> > + &dev_attr_temp1_crit.attr,
> > + &dev_attr_temp1_min.attr,
> > + &dev_attr_temp1_max.attr,
> > + &dev_attr_temp1_crit_hyst.attr,
> > + &dev_attr_temp1_max_hyst.attr,
> > + &sensor_dev_attr_temp1_crit_alarm.dev_attr.attr,
> > + &sensor_dev_attr_temp1_min_alarm.dev_attr.attr,
> > + &sensor_dev_attr_temp1_max_alarm.dev_attr.attr,
> > + NULL
> > +};
> > +
> > +static const struct attribute_group jc42_group = {
> > + .attrs = jc42_attributes,
> > +};
> > +
> > +/* Return 0 if detection is successful, -ENODEV otherwise */
> > +static int jc42_detect(struct i2c_client *new_client,
> > + struct i2c_board_info *info)
> > +{
> > + struct i2c_adapter *adapter = new_client->adapter;
> > + int i, config, cap, manid, devid;
> > +
> > + if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA |
> > + I2C_FUNC_SMBUS_WORD_DATA))
> > + return -ENODEV;
> > +
> > + cap = jc42_read_value(new_client, JC42_REG_CAP);
> > + config = jc42_read_value(new_client, JC42_REG_CONFIG);
> > + manid = jc42_read_value(new_client, JC42_REG_MANID);
> > + devid = jc42_read_value(new_client, JC42_REG_DEVICEID);
> > +
> > + if (cap < 0 || config < 0 || manid < 0 || devid < 0)
> > + return -ENODEV;
> > +
> > + if ((cap & 0xff00) || (config & 0xf800))
> > + return -ENODEV;
> > +
> > + for (i = 0; i < ARRAY_SIZE(jc42_chips); i++) {
> > + if (manid == jc42_chips[i].manid
> > + && (devid & jc42_chips[i].devid_mask) ==
> > + jc42_chips[i].devid) {
> > + strlcpy(info->type, "jc42", I2C_NAME_SIZE);
> > + return 0;
> > + }
> > + }
> > + return -ENODEV;
> > +}
> > +
> > +static int jc42_probe(struct i2c_client *new_client,
> > + const struct i2c_device_id *id)
> > +{
> > + struct jc42_data *data;
> > + int config, cap, err;
> > +
> > + data = kzalloc(sizeof(struct jc42_data), GFP_KERNEL);
> > + if (!data) {
> > + err = -ENOMEM;
> > + goto exit;
> > + }
> > +
> > + i2c_set_clientdata(new_client, data);
> > + data->valid = false;
> > + mutex_init(&data->update_lock);
> > +
> > + cap = jc42_read_value(new_client, JC42_REG_CAP);
> > + if (cap < 0) {
> > + err = -EINVAL;
> > + goto exit_free;
> > + }
> > + data->extended = !!(cap & JC42_CAP_RANGE);
> > +
> > + config = jc42_read_value(new_client, JC42_REG_CONFIG);
> > + if (config < 0) {
> > + err = -EINVAL;
> > + goto exit_free;
> > + }
> > + data->orig_config = config;
> > + if (config & JC42_CFG_SHUTDOWN) {
> > + config &= ~JC42_CFG_SHUTDOWN;
> > + jc42_write_value(new_client, JC42_REG_CONFIG, config);
> > + }
> > + data->config = config;
> > +
> > + /* Register sysfs hooks */
> > + err = sysfs_create_group(&new_client->dev.kobj, &jc42_group);
> > + if (err)
> > + goto exit_free;
> > +
> > + data->hwmon_dev = hwmon_device_register(&new_client->dev);
> > + if (IS_ERR(data->hwmon_dev)) {
> > + err = PTR_ERR(data->hwmon_dev);
> > + goto exit_remove;
> > + }
> > +
> > + return 0;
> > +
> > +exit_remove:
> > + sysfs_remove_group(&new_client->dev.kobj, &jc42_group);
> > +exit_free:
> > + kfree(data);
> > +exit:
> > + return err;
> > +}
> > +
> > +static int jc42_remove(struct i2c_client *client)
> > +{
> > + struct jc42_data *data = i2c_get_clientdata(client);
> > + hwmon_device_unregister(data->hwmon_dev);
> > + sysfs_remove_group(&client->dev.kobj, &jc42_group);
> > + if (data->config != data->orig_config)
> > + jc42_write_value(client, JC42_REG_CONFIG, data->orig_config);
> > + kfree(data);
> > + return 0;
> > +}
> > +
> > +/* All registers are word-sized. */
> > +static int jc42_read_value(struct i2c_client *client, u8 reg)
> > +{
> > + int ret = i2c_smbus_read_word_data(client, reg);
> > + if (ret < 0)
> > + return ret;
> > + return swab16(ret);
> > +}
> > +
> > +static int jc42_write_value(struct i2c_client *client, u8 reg, u16 value)
> > +{
> > + return i2c_smbus_write_word_data(client, reg, swab16(value));
> > +}
> > +
> > +static struct jc42_data *jc42_update_device(struct device *dev)
> > +{
> > + struct i2c_client *client = to_i2c_client(dev);
> > + struct jc42_data *data = i2c_get_clientdata(client);
> > + struct jc42_data *ret = data;
> > + int val;
> > +
> > + mutex_lock(&data->update_lock);
> > +
> > + if (time_after(jiffies, data->last_updated + HZ) || !data->valid) {
> > + val = jc42_read_value(client, JC42_REG_TEMP);
> > + if (val < 0) {
> > + ret = ERR_PTR(val);
> > + goto abort;
> > + }
> > + data->temp_input = val;
> > +
> > + val = jc42_read_value(client, JC42_REG_TEMP_CRITICAL);
> > + if (val < 0) {
> > + ret = ERR_PTR(val);
> > + goto abort;
> > + }
> > + data->temp_crit = val;
> > +
> > + val = jc42_read_value(client, JC42_REG_TEMP_LOWER);
> > + if (val < 0) {
> > + ret = ERR_PTR(val);
> > + goto abort;
> > + }
> > + data->temp_min = val;
> > +
> > + val = jc42_read_value(client, JC42_REG_TEMP_UPPER);
> > + if (val < 0) {
> > + ret = ERR_PTR(val);
> > + goto abort;
> > + }
> > + data->temp_max = val;
> > +
> > + data->last_updated = jiffies;
> > + data->valid = true;
> > + }
> > +abort:
> > + mutex_unlock(&data->update_lock);
> > + return ret;
> > +}
> > +
> > +static int __init sensors_jc42_init(void)
> > +{
> > + return i2c_add_driver(&jc42_driver);
> > +}
> > +
> > +static void __exit sensors_jc42_exit(void)
> > +{
> > + i2c_del_driver(&jc42_driver);
> > +}
> > +
> > +MODULE_AUTHOR("Guenter Roeck <[email protected]>");
> > +MODULE_DESCRIPTION("JC42 driver");
> > +MODULE_LICENSE("GPL");
> > +
> > +module_init(sensors_jc42_init);
> > +module_exit(sensors_jc42_exit);
> > --
> > 1.7.0.87.g0901d
> >
> > --
> > To unsubscribe from this list: send the line "unsubscribe linux-i2c" in
> > the body of a message to [email protected]
> > More majordomo info at http://vger.kernel.org/majordomo-info.html
> >
>
> -------------------------------------------------------------------------
> | Paul Goyette | PGP Key fingerprint: | E-mail addresses: |
> | Customer Service | FA29 0E3B 35AF E8AE 6651 | paul at whooppee.com |
> | Network Engineer | 0786 F758 55DE 53BA 7731 | pgoyette at juniper.net |
> | Kernel Developer | | pgoyette at netbsd.org |
> -------------------------------------------------------------------------