It was observed the Host Clock Divider was not written by the driver. It
was still set to (default) 0, if not already set by BIOS, which caused
garbage on SMBus.
This driver adds 2 parameters which are used to calculate the divider
appropriately. This new divider is only applied if the clock divider is
still default 0.
Signed-off-by: Alexander Stein <[email protected]>
Tested-by: Adam Pribyl <[email protected]>
---
Changes in v2:
* HSTCLK register is 16 Bit, not 8 Bit. Thanks to Adam for detecting
drivers/i2c/busses/i2c-isch.c | 12 ++++++++++++
1 files changed, 12 insertions(+), 0 deletions(-)
diff --git a/drivers/i2c/busses/i2c-isch.c b/drivers/i2c/busses/i2c-isch.c
index 6561d27..bdfddf8 100644
--- a/drivers/i2c/busses/i2c-isch.c
+++ b/drivers/i2c/busses/i2c-isch.c
@@ -40,6 +40,7 @@
/* SCH SMBus address offsets */
#define SMBHSTCNT (0 + sch_smba)
#define SMBHSTSTS (1 + sch_smba)
+#define SMBHSTCLK (2 + sch_smba)
#define SMBHSTADD (4 + sch_smba) /* TSA */
#define SMBHSTCMD (5 + sch_smba)
#define SMBHSTDAT0 (6 + sch_smba)
@@ -58,6 +59,8 @@
static unsigned short sch_smba;
static struct i2c_adapter sch_adapter;
+static int smbus_speed = 100; /* SMBus bus speed in Kbps */
+static int backbone_speed = 33000; /* backbone speed in KHz */
/*
* Start the i2c transaction -- the i2c_access will prepare the transaction
@@ -156,6 +159,13 @@ static s32 sch_access(struct i2c_adapter *adap, u16 addr,
dev_dbg(&sch_adapter.dev, "SMBus busy (%02x)\n", temp);
return -EAGAIN;
}
+ temp = inw(SMBHSTCLK);
+ if (!temp) {
+ dev_notice(&sch_adapter.dev, "clock divider unitialized. Setting module defaults\n");
+ dev_dbg(&sch_adapter.dev, "access speed: %d KHz\n", smbus_speed);
+ outw((backbone_speed / 4) / smbus_speed, SMBHSTCLK);
+ }
+
dev_dbg(&sch_adapter.dev, "access size: %d %s\n", size,
(read_write)?"READ":"WRITE");
switch (size) {
@@ -312,3 +322,5 @@ MODULE_AUTHOR("Jacob Pan <[email protected]>");
MODULE_DESCRIPTION("Intel SCH SMBus driver");
MODULE_LICENSE("GPL");
MODULE_ALIAS("platform:isch_smbus");
+module_param(smbus_speed, int, (S_IRUSR | S_IWUSR));
+module_param(backbone_speed, int, (S_IRUSR | S_IWUSR));
--
1.7.3.4
On Wed, Feb 15, 2012 at 03:36:49PM +0100, Alexander Stein wrote:
> It was observed the Host Clock Divider was not written by the driver. It
> was still set to (default) 0, if not already set by BIOS, which caused
> garbage on SMBus.
> This driver adds 2 parameters which are used to calculate the divider
> appropriately. This new divider is only applied if the clock divider is
> still default 0.
>
> Signed-off-by: Alexander Stein <[email protected]>
> Tested-by: Adam Pribyl <[email protected]>
> ---
I don't know the hardware: Can it have multiple SmBusses? Then, a module
parameter would force all of them to the selected mode. Do you really
need the parameter? Maybe defaulting to 100Kbps is sane enough?
@Jean: Is this an embedded driver? :)
> Changes in v2:
> * HSTCLK register is 16 Bit, not 8 Bit. Thanks to Adam for detecting
>
> drivers/i2c/busses/i2c-isch.c | 12 ++++++++++++
> 1 files changed, 12 insertions(+), 0 deletions(-)
>
> diff --git a/drivers/i2c/busses/i2c-isch.c b/drivers/i2c/busses/i2c-isch.c
> index 6561d27..bdfddf8 100644
> --- a/drivers/i2c/busses/i2c-isch.c
> +++ b/drivers/i2c/busses/i2c-isch.c
> @@ -40,6 +40,7 @@
> /* SCH SMBus address offsets */
> #define SMBHSTCNT (0 + sch_smba)
> #define SMBHSTSTS (1 + sch_smba)
> +#define SMBHSTCLK (2 + sch_smba)
> #define SMBHSTADD (4 + sch_smba) /* TSA */
> #define SMBHSTCMD (5 + sch_smba)
> #define SMBHSTDAT0 (6 + sch_smba)
> @@ -58,6 +59,8 @@
>
> static unsigned short sch_smba;
> static struct i2c_adapter sch_adapter;
> +static int smbus_speed = 100; /* SMBus bus speed in Kbps */
> +static int backbone_speed = 33000; /* backbone speed in KHz */
>
> /*
> * Start the i2c transaction -- the i2c_access will prepare the transaction
> @@ -156,6 +159,13 @@ static s32 sch_access(struct i2c_adapter *adap, u16 addr,
> dev_dbg(&sch_adapter.dev, "SMBus busy (%02x)\n", temp);
> return -EAGAIN;
> }
> + temp = inw(SMBHSTCLK);
> + if (!temp) {
> + dev_notice(&sch_adapter.dev, "clock divider unitialized. Setting module defaults\n");
> + dev_dbg(&sch_adapter.dev, "access speed: %d KHz\n", smbus_speed);
> + outw((backbone_speed / 4) / smbus_speed, SMBHSTCLK);
> + }
> +
> dev_dbg(&sch_adapter.dev, "access size: %d %s\n", size,
> (read_write)?"READ":"WRITE");
> switch (size) {
> @@ -312,3 +322,5 @@ MODULE_AUTHOR("Jacob Pan <[email protected]>");
> MODULE_DESCRIPTION("Intel SCH SMBus driver");
> MODULE_LICENSE("GPL");
> MODULE_ALIAS("platform:isch_smbus");
> +module_param(smbus_speed, int, (S_IRUSR | S_IWUSR));
> +module_param(backbone_speed, int, (S_IRUSR | S_IWUSR));
> --
> 1.7.3.4
>
Regards,
Wolfram
--
Pengutronix e.K. | Wolfram Sang |
Industrial Linux Solutions | http://www.pengutronix.de/ |