This patch series adds support for max77686 which is a multifunction device which
includes regulator (pmic), rtc and charger sub-blocks within it. The support for
mfd driver and regulator driver are added by this patch series. This patch series
also includes device tree and irqdomain support for mfd and regulator portions.
Implemented the required modification, stated in the recieved review comments.
changes since V1:
-added regmap support.
-implemented .get_voltage_sel, .set_voltage_sel and .set_voltage_time_sel after
removing .get_voltage and .set_voltage in regulator driver.
-used of_regulator_match() for parsing DT.
-added Documentation for Devive Tree binding.
This patch series is based on mark_regulator/for-next and has been tested on
GAIA board.
Yadwinder Singh Brar (2):
mfd: Add support for MAX77686.
regulator: Add support for MAX77686.
Documentation/devicetree/bindings/mfd/max77686.txt | 63 +++
drivers/mfd/Kconfig | 21 +
drivers/mfd/Makefile | 1 +
drivers/mfd/max77686-irq.c | 255 ++++++++++
drivers/mfd/max77686.c | 322 ++++++++++++
drivers/regulator/Kconfig | 9 +
drivers/regulator/Makefile | 1 +
drivers/regulator/max77686.c | 512 ++++++++++++++++++++
include/linux/mfd/max77686-private.h | 282 +++++++++++
include/linux/mfd/max77686.h | 100 ++++
10 files changed, 1566 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/mfd/max77686.txt
create mode 100644 drivers/mfd/max77686-irq.c
create mode 100644 drivers/mfd/max77686.c
create mode 100644 drivers/regulator/max77686.c
create mode 100644 include/linux/mfd/max77686-private.h
create mode 100644 include/linux/mfd/max77686.h
MAX77686 is a mulitifunction device with PMIC, RTC and Charger on chip. This
driver provides common support for accessing the device. This is initial
version of this driver that supports to enable the chip with its primary I2C
bus.It also includes IRQ and device tree support for MAX77686 chip.
Signed-off-by: Yadwinder Singh Brar <[email protected]>
---
Documentation/devicetree/bindings/mfd/max77686.txt | 63 ++++
drivers/mfd/Kconfig | 21 ++
drivers/mfd/Makefile | 1 +
drivers/mfd/max77686-irq.c | 255 ++++++++++++++++
drivers/mfd/max77686.c | 322 ++++++++++++++++++++
include/linux/mfd/max77686-private.h | 282 +++++++++++++++++
include/linux/mfd/max77686.h | 100 ++++++
7 files changed, 1044 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/mfd/max77686.txt
create mode 100644 drivers/mfd/max77686-irq.c
create mode 100644 drivers/mfd/max77686.c
create mode 100644 include/linux/mfd/max77686-private.h
create mode 100644 include/linux/mfd/max77686.h
diff --git a/Documentation/devicetree/bindings/mfd/max77686.txt b/Documentation/devicetree/bindings/mfd/max77686.txt
new file mode 100644
index 0000000..72e7933
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/max77686.txt
@@ -0,0 +1,63 @@
+Maxim MAX77686 multi-function device
+
+MAX77686 is a Mulitifunction device with PMIC, RTC and Charger on chip. It is
+interfaced to host controller using i2c interface. PMIC and Charger submodules
+are addressed using same i2c slave address where as RTC submodule uses
+different slave address,presently for which we are statically creating i2c
+client while probing.This document describes the binding for mfd device and
+PMIC submodule.
+
+Required properties:
+- compatible : Must be "maxim,max77686";
+- reg : Specifiec the i2c slave address of PMIC block.
+- interrupts : This i2c device has an IRQ line connected to the main SoC.
+- interrupt-parent : The parent interrupt controller.
+
+Optional node:
+- max77686,buck_ramp_delay : Ramp delay to be setup for buck2,3&4.
+
+
+- voltage-regulators : The regulators of max77686 have to be instantiated
+ under subnode named "voltage-regulators" uing the following format.
+
+ regulator_name {
+ standard regulator constraints....
+ };
+ refer Documentation/devicetree/bindings/regulator/regulator.txt
+
+ The names of regulator should be as follow:
+
+ -LDOn : for LDOs, where n can lie in range 1 to 26.
+ example: LDO1, LDO2, LDO26.
+ -BUCKn : for BUCKs, where n can lie in range 1 to 9.
+ example: BUCK1, BUCK5, BUCK9.
+
+
+Example:
+
+
+ max77686_pmic@09 {
+ compatible = "maxim,max77686";
+ interrupt-parent = <&wakeup_eint>;
+ interrupts = <26 0>;
+ reg = <0x09>;
+
+ max77686,buck_ramp_delay = <2>; /* default */
+
+ voltage-regulators {
+ ldo11_reg: LDO11 {
+ regulator-name = "vdd_ldo11";
+ regulator-min-microvolt = <1900000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-always-on;
+ };
+
+ buck1_reg: BUCK1 {
+ regulator-name = "vdd_mif";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ }
+
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 29f463c..06a0a85 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -434,6 +434,27 @@ config MFD_MAX8998
additional drivers must be enabled in order to use the functionality
of the device.
+config MFD_MAX77686
+ bool "Maxim Semiconductor MAX77686 PMIC Support"
+ depends on I2C=y && GENERIC_HARDIRQS
+ select MFD_CORE
+ select REGMAP_I2C
+ help
+ Say yes here to support for Maxim Semiconductor MAX77686.
+ This is a Power Management IC with RTC on chip.
+ This driver provides common support for accessing the device;
+ additional drivers must be enabled in order to use the functionality
+ of the device.
+
+config DEBUG_MAX77686
+ bool "MAX77686 PMIC debugging"
+ depends on MFD_MAX77686
+ help
+ Say yes, if you need enable debug messages in
+ MFD_MAX77686 driver.
+ Further for enabling/disabling particular type of debug
+ messages set max77686_debug_mask accordingly.
+
config MFD_S5M_CORE
bool "SAMSUNG S5M Series Support"
depends on I2C=y && GENERIC_HARDIRQS
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 05fa538..19ecca9 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -79,6 +79,7 @@ max8925-objs := max8925-core.o max8925-i2c.o
obj-$(CONFIG_MFD_MAX8925) += max8925.o
obj-$(CONFIG_MFD_MAX8997) += max8997.o max8997-irq.o
obj-$(CONFIG_MFD_MAX8998) += max8998.o max8998-irq.o
+obj-$(CONFIG_MFD_MAX77686) += max77686.o max77686-irq.o
pcf50633-objs := pcf50633-core.o pcf50633-irq.o
obj-$(CONFIG_MFD_PCF50633) += pcf50633.o
diff --git a/drivers/mfd/max77686-irq.c b/drivers/mfd/max77686-irq.c
new file mode 100644
index 0000000..f57b96e
--- /dev/null
+++ b/drivers/mfd/max77686-irq.c
@@ -0,0 +1,255 @@
+/*
+ * max77686-irq.c - Interrupt controller support for MAX77686
+ *
+ * Copyright (C) 2012 Samsung Electronics Co.Ltd
+ * Chiwoong Byun <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ * This driver is based on max8997-irq.c
+ */
+
+#include <linux/err.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/max77686.h>
+#include <linux/mfd/max77686-private.h>
+#include <linux/irqdomain.h>
+
+#define IRQ_GRP (data->hwirq >> 3)
+#define IRQ_MASK (1 << (data->hwirq & 7))
+
+int max77686_debug_mask = MAX77686_DEBUG_INFO; /* enable debug prints */
+
+static const int max77686_mask_reg[] = {
+ [PMIC_INT1] = MAX77686_REG_INT1MSK,
+ [PMIC_INT2] = MAX77686_REG_INT2MSK,
+ [RTC_INT] = MAX77686_RTC_INTM,
+};
+
+static struct i2c_client *max77686_get_i2c(struct max77686_dev *max77686,
+ enum max77686_irq_source src)
+{
+ switch (src) {
+ case PMIC_INT1...PMIC_INT2:
+ return max77686->i2c;
+ case RTC_INT:
+ return max77686->rtc;
+ default:
+ return ERR_PTR(-EINVAL);
+ }
+}
+
+static void max77686_irq_lock(struct irq_data *data)
+{
+ struct max77686_dev *max77686 = irq_get_chip_data(data->irq);
+
+ mutex_lock(&max77686->irqlock);
+}
+
+static void max77686_irq_sync_unlock(struct irq_data *data)
+{
+ struct max77686_dev *max77686 = irq_get_chip_data(data->irq);
+ int i;
+
+ for (i = 0; i < MAX77686_IRQ_GROUP_NR; i++) {
+ int mask_reg = max77686_mask_reg[i];
+ struct i2c_client *i2c = max77686_get_i2c(max77686, i);
+
+ dbg_mask("%s: mask_reg[%d]=0x%x, cur=0x%x\n",
+ __func__, i, mask_reg, max77686->irq_masks_cur[i]);
+
+ if (mask_reg == MAX77686_REG_INVALID || IS_ERR_OR_NULL(i2c))
+ continue;
+
+ max77686->irq_masks_cache[i] = max77686->irq_masks_cur[i];
+
+ max77686_write_reg(i2c, max77686_mask_reg[i],
+ max77686->irq_masks_cur[i]);
+ }
+
+ mutex_unlock(&max77686->irqlock);
+}
+
+static void max77686_irq_mask(struct irq_data *data)
+{
+ struct max77686_dev *max77686 = irq_get_chip_data(data->irq);
+
+ max77686->irq_masks_cur[IRQ_GRP] |= IRQ_MASK;
+ dbg_mask("%s: group=%x, cur=0x%x\n",
+ __func__, IRQ_GRP,
+ max77686->irq_masks_cur[IRQ_GRP]);
+
+}
+
+static void max77686_irq_unmask(struct irq_data *data)
+{
+ struct max77686_dev *max77686 = irq_get_chip_data(data->irq);
+
+ max77686->irq_masks_cur[IRQ_GRP] &= ~IRQ_MASK;
+ dbg_mask("%s: group=%x, cur=0x%x\n",
+ __func__, IRQ_GRP,
+ max77686->irq_masks_cur[IRQ_GRP]);
+
+}
+
+static struct irq_chip max77686_irq_chip = {
+ .name = "max77686",
+ .irq_bus_lock = max77686_irq_lock,
+ .irq_bus_sync_unlock = max77686_irq_sync_unlock,
+ .irq_mask = max77686_irq_mask,
+ .irq_unmask = max77686_irq_unmask,
+};
+
+static irqreturn_t max77686_irq_thread(int irq, void *data)
+{
+ struct max77686_dev *max77686 = data;
+ int irq_reg[MAX77686_IRQ_GROUP_NR] = { };
+ int irq_src;
+ int ret, grp, i, cur_irq;
+
+ ret = max77686_read_reg(max77686->i2c, MAX77686_REG_INTSRC, &irq_src);
+ if (ret < 0) {
+ dev_err(max77686->dev, "Failed to read interrupt source: %d\n",
+ ret);
+ return IRQ_NONE;
+ }
+
+ ret = max77686_bulk_read(max77686->i2c, MAX77686_REG_INT1,
+ 2, irq_reg);
+ if (ret < 0) {
+ dev_err(max77686->dev,
+ "Failed to read pmic interrupt: %d\n", ret);
+ return IRQ_NONE;
+ }
+
+ dbg_int("%s: int1=0x%x, int2=0x%x\n", __func__,
+ irq_reg[PMIC_INT1], irq_reg[PMIC_INT2]);
+
+ if (irq_src & MAX77686_IRQSRC_RTC) {
+ ret = max77686_read_reg(max77686->rtc, MAX77686_RTC_INT,
+ &irq_reg[RTC_INT]);
+ if (ret < 0) {
+ dev_err(max77686->dev,
+ "Failed to read rtc interrupt: %d\n", ret);
+ return IRQ_NONE;
+ }
+ dbg_int("%s: rtc int=0x%x\n", __func__,
+ irq_reg[RTC_INT]);
+
+ }
+
+ for (grp = 0; grp < MAX77686_IRQ_GROUP_NR; grp++) {
+ irq_reg[grp] &= ~max77686->irq_masks_cur[grp];
+ i = 0;
+ while (irq_reg[grp]) {
+ if (irq_reg[grp] & (1 << i)) {
+ cur_irq = irq_find_mapping(max77686->irq_domain,
+ grp*8 + i);
+ if (cur_irq)
+ handle_nested_irq(cur_irq);
+
+ irq_reg[grp] &= ~(1 << i);
+ dbg_int("%s: Handled irq:%x from group:%x\n",
+ __func__, i, grp);
+ }
+ i++;
+ }
+ }
+
+ dbg_info("%s returning\n", __func__);
+
+ return IRQ_HANDLED;
+}
+
+int max77686_irq_resume(struct max77686_dev *max77686)
+{
+ if (max77686->irq && max77686->irq_domain)
+ max77686_irq_thread(0, max77686);
+
+ return 0;
+}
+
+static int max77686_irq_domain_map(struct irq_domain *d, unsigned int irq,
+ irq_hw_number_t hw)
+{
+ struct max77686_dev *max77686 = d->host_data;
+
+ irq_set_chip_data(irq, max77686);
+ irq_set_chip_and_handler(irq, &max77686_irq_chip, handle_edge_irq);
+ irq_set_nested_thread(irq, 1);
+ set_irq_flags(irq, IRQF_VALID);
+ return 0;
+}
+
+static struct irq_domain_ops max77686_irq_domain_ops = {
+ .map = max77686_irq_domain_map,
+};
+
+int max77686_irq_init(struct max77686_dev *max77686)
+{
+ int i, ret;
+ struct irq_domain *domain;
+
+ if (!max77686->irq) {
+ dev_err(max77686->dev,
+ "No interrupt specified.\n");
+ return -ENODEV;
+ }
+
+ mutex_init(&max77686->irqlock);
+
+ /* Mask individual interrupt sources */
+ for (i = 0; i < MAX77686_IRQ_GROUP_NR; i++) {
+ struct i2c_client *i2c;
+
+ max77686->irq_masks_cur[i] = 0xff;
+ max77686->irq_masks_cache[i] = 0xff;
+ i2c = max77686_get_i2c(max77686, i);
+
+ if (IS_ERR_OR_NULL(i2c))
+ continue;
+ if (max77686_mask_reg[i] == MAX77686_REG_INVALID)
+ continue;
+
+ max77686_write_reg(i2c, max77686_mask_reg[i], 0xff);
+ }
+
+ domain = irq_domain_add_linear(NULL, MAX77686_IRQ_NR,
+ &max77686_irq_domain_ops, &max77686);
+ if (!domain) {
+ dev_err(max77686->dev, "could not create irq domain\n");
+ return -ENODEV;
+ }
+
+ ret = request_threaded_irq(max77686->irq, NULL, max77686_irq_thread,
+ IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
+ "max77686-irq", max77686);
+ if (ret) {
+ dev_err(max77686->dev, "Failed to request IRQ %d: %d\n",
+ max77686->irq, ret);
+ return ret;
+ }
+
+ dbg_info("%s : done\n", __func__);
+
+ return 0;
+}
+
+void max77686_irq_exit(struct max77686_dev *max77686)
+{
+ if (max77686->irq)
+ free_irq(max77686->irq, max77686);
+}
diff --git a/drivers/mfd/max77686.c b/drivers/mfd/max77686.c
new file mode 100644
index 0000000..1948fb4
--- /dev/null
+++ b/drivers/mfd/max77686.c
@@ -0,0 +1,322 @@
+/*
+ * max77686.c - mfd core driver for the Maxim 77686
+ *
+ * Copyright (C) 2012 Samsung Electronics Co.Ltd.
+ * Chiwoong Byun <[email protected]>
+ * Yadwinder Singh Brar <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ * This driver is based on max8997.c
+ */
+
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/err.h>
+#include <linux/pm_runtime.h>
+#include <linux/regmap.h>
+#include <linux/mutex.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/max77686.h>
+#include <linux/mfd/max77686-private.h>
+
+#define I2C_ADDR_RTC (0x0c >> 1)
+
+#ifdef CONFIG_OF
+static struct of_device_id __devinitdata max77686_pmic_dt_match[] = {
+ {.compatible = "maxim,max77686-pmic", .data = 0},
+ {},
+};
+#endif
+
+static struct mfd_cell max77686_devs[] = {
+ {.name = "max77686-pmic",},
+ {.name = "max77686-rtc",},
+};
+
+struct regmap_config pmic_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = MAX77686_REG_32KHZ,
+};
+
+struct regmap_config rtc_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = MAX77686_ALARM2_DATE,
+};
+
+int max77686_read_reg(struct i2c_client *i2c, int reg, int *buf)
+{
+ struct max77686_dev *max77686 = i2c_get_clientdata(i2c);
+
+ if (i2c == max77686->i2c)
+ return regmap_read(max77686->regmap, reg, buf);
+ else
+ return regmap_read(max77686->rtc_regmap, reg, buf);
+}
+EXPORT_SYMBOL_GPL(max77686_read_reg);
+
+int max77686_bulk_read(struct i2c_client *i2c, int reg, int count,
+ int *buf)
+{
+ struct max77686_dev *max77686 = i2c_get_clientdata(i2c);
+
+ if (i2c == max77686->i2c)
+ return regmap_bulk_read(max77686->regmap, reg, buf, count);
+ else
+ return regmap_bulk_read(max77686->rtc_regmap, reg, buf, count);
+}
+EXPORT_SYMBOL_GPL(max77686_bulk_read);
+
+int max77686_write_reg(struct i2c_client *i2c, int reg, int buf)
+{
+ struct max77686_dev *max77686 = i2c_get_clientdata(i2c);
+ if (i2c == max77686->i2c)
+ return regmap_write(max77686->regmap, reg, buf);
+ else
+ return regmap_write(max77686->rtc_regmap, reg, buf);
+}
+EXPORT_SYMBOL_GPL(max77686_write_reg);
+
+int max77686_bulk_write(struct i2c_client *i2c, int reg, int count,
+ int *buf)
+{
+ struct max77686_dev *max77686 = i2c_get_clientdata(i2c);
+
+ if (i2c == max77686->i2c)
+ return regmap_bulk_write(max77686->regmap, reg, buf, count);
+ else
+ return regmap_bulk_write(max77686->rtc_regmap, reg, buf, count);
+}
+EXPORT_SYMBOL_GPL(max77686_bulk_write);
+
+int max77686_update_reg(struct i2c_client *i2c, int reg, int val, int mask)
+{
+ struct max77686_dev *max77686 = i2c_get_clientdata(i2c);
+ if (i2c == max77686->i2c)
+ return regmap_update_bits(max77686->regmap, reg, mask, val);
+ else
+ return regmap_update_bits(max77686->rtc_regmap, reg, mask, val);
+}
+EXPORT_SYMBOL_GPL(max77686_update_reg);
+
+#ifdef CONFIG_OF
+static struct max77686_platform_data *max77686_i2c_parse_dt_pdata(struct device
+ *dev)
+{
+ struct max77686_platform_data *pd;
+
+ pd = devm_kzalloc(dev, sizeof(*pd), GFP_KERNEL);
+ if (!pd) {
+ dev_err(dev, "could not allocate memory for pdata\n");
+ return ERR_PTR(-ENOMEM);
+ }
+
+ return pd;
+}
+#else
+static struct max77686_platform_data *max77686_i2c_parse_dt_pdata(struct device
+ *dev)
+{
+ return 0;
+}
+#endif
+
+static inline int max77686_i2c_get_driver_data(struct i2c_client *i2c,
+ const struct i2c_device_id *id)
+{
+#ifdef CONFIG_OF
+ if (i2c->dev.of_node) {
+ const struct of_device_id *match;
+ match = of_match_node(max77686_pmic_dt_match,
+ i2c->dev.of_node);
+ return (int)match->data;
+ }
+#endif
+ return (int)id->driver_data;
+}
+
+static int max77686_i2c_probe(struct i2c_client *i2c,
+ const struct i2c_device_id *id)
+{
+ struct max77686_dev *max77686;
+ struct max77686_platform_data *pdata = i2c->dev.platform_data;
+ int ret = 0;
+ int data;
+
+ max77686 = devm_kzalloc(&i2c->dev, sizeof(struct max77686_dev),
+ GFP_KERNEL);
+ if (max77686 == NULL) {
+ dev_err(max77686->dev, "could not allocate memory\n");
+ return -ENOMEM;
+ }
+
+ max77686->dev = &i2c->dev;
+
+ if (max77686->dev->of_node) {
+ pdata = max77686_i2c_parse_dt_pdata(max77686->dev);
+ if (IS_ERR(pdata)) {
+ dev_err(max77686->dev, "Unable to parse device tree\n");
+ return PTR_ERR(pdata);
+ }
+ }
+
+ if (!pdata) {
+ dev_err(max77686->dev, "No platform data found\n");
+ return -ENODEV;
+ }
+
+ i2c_set_clientdata(i2c, max77686);
+ max77686->i2c = i2c;
+ max77686->irq = i2c->irq;
+ max77686->type = max77686_i2c_get_driver_data(i2c, id);
+
+ max77686->pdata = pdata;
+ max77686->regmap = devm_regmap_init_i2c(max77686->i2c,
+ &pmic_regmap_config);
+ if (IS_ERR(max77686->regmap)) {
+ dev_err(max77686->dev, "Failed to allocate register map: %d\n",
+ ret);
+ return PTR_ERR(max77686->regmap);
+ }
+
+ max77686->rtc = i2c_new_dummy(i2c->adapter, I2C_ADDR_RTC);
+ i2c_set_clientdata(max77686->rtc, max77686);
+ max77686->rtc_regmap = devm_regmap_init_i2c(max77686->rtc,
+ &rtc_regmap_config);
+ if (IS_ERR(max77686->rtc_regmap)) {
+ dev_err(max77686->dev, "rtc register mapping failed %d\n", ret);
+ ret = PTR_ERR(max77686->rtc_regmap);
+ goto err_i2c;
+ }
+
+ ret = max77686_read_reg(i2c, MAX77686_REG_DEVICE_ID, &data);
+ if (ret < 0) {
+ dev_err(max77686->dev, "device not found on this channel\n");
+ goto err_i2c;
+ } else
+ if (data & CHIP_REV)
+ dev_info(max77686->dev, "device found with id:0x%x\n"
+ , data);
+ else {
+ dev_err(max77686->dev, "inappropriate dev id\n");
+ goto err_i2c;
+ }
+
+ ret = mfd_add_devices(max77686->dev, -1, max77686_devs,
+ ARRAY_SIZE(max77686_devs), NULL, 0);
+
+ if (ret < 0) {
+ dev_err(max77686->dev, "mfd_add_devices failed\n");
+ goto err_i2c;
+ }
+
+ ret = max77686_irq_init(max77686);
+ if (ret < 0) {
+ dev_err(max77686->dev, "max77686_irq_init failed\n");
+ goto err_mfd;
+ }
+
+ pm_runtime_set_active(max77686->dev);
+ device_init_wakeup(max77686->dev, true);
+
+ return ret;
+
+ err_mfd:
+ mfd_remove_devices(max77686->dev);
+ err_i2c:
+ i2c_unregister_device(max77686->rtc);
+ return ret;
+}
+
+static int max77686_i2c_remove(struct i2c_client *i2c)
+{
+ struct max77686_dev *max77686 = i2c_get_clientdata(i2c);
+
+ device_init_wakeup(max77686->dev, 0);
+ pm_runtime_set_suspended(max77686->dev);
+ max77686_irq_exit(max77686);
+ mfd_remove_devices(max77686->dev);
+ i2c_unregister_device(max77686->rtc);
+ return 0;
+}
+
+static const struct i2c_device_id max77686_i2c_id[] = {
+ {"max77686", 0},
+ {}
+};
+
+MODULE_DEVICE_TABLE(i2c, max77686_i2c_id);
+
+static int max77686_suspend(struct device *dev)
+{
+ struct i2c_client *i2c = container_of(dev, struct i2c_client, dev);
+ struct max77686_dev *max77686 = i2c_get_clientdata(i2c);
+
+ if (device_may_wakeup(dev))
+ enable_irq_wake(max77686->irq);
+
+ return 0;
+}
+
+static int max77686_resume(struct device *dev)
+{
+ struct i2c_client *i2c = container_of(dev, struct i2c_client, dev);
+ struct max77686_dev *max77686 = i2c_get_clientdata(i2c);
+
+ if (device_may_wakeup(dev))
+ disable_irq_wake(max77686->irq);
+
+ max77686_irq_resume(max77686);
+ return 0;
+}
+
+const struct dev_pm_ops max77686_pm = {
+ .suspend = max77686_suspend,
+ .resume = max77686_resume,
+};
+
+static struct i2c_driver max77686_i2c_driver = {
+ .driver = {
+ .name = "max77686",
+ .owner = THIS_MODULE,
+ .pm = &max77686_pm,
+ .of_match_table = of_match_ptr(max77686_pmic_dt_match),
+ },
+ .probe = max77686_i2c_probe,
+ .remove = max77686_i2c_remove,
+ .id_table = max77686_i2c_id,
+};
+
+static int __init max77686_i2c_init(void)
+{
+ return i2c_add_driver(&max77686_i2c_driver);
+}
+
+static void __exit max77686_i2c_exit(void)
+{
+ i2c_del_driver(&max77686_i2c_driver);
+}
+
+subsys_initcall(max77686_i2c_init);
+module_exit(max77686_i2c_exit);
+
+MODULE_DESCRIPTION("MAXIM 77686 multi-function core driver");
+MODULE_AUTHOR("Chiwoong Byun <[email protected]>");
+MODULE_AUTHOR("Yadwinder Singh Brar <[email protected]>");
+MODULE_LICENSE("GPL");
diff --git a/include/linux/mfd/max77686-private.h b/include/linux/mfd/max77686-private.h
new file mode 100644
index 0000000..7abb331
--- /dev/null
+++ b/include/linux/mfd/max77686-private.h
@@ -0,0 +1,282 @@
+/*
+ * max77686.h - Voltage regulator driver for the Maxim 77686
+ *
+ * Copyright (C) 2011 Samsung Electrnoics
+ * Chiwoong Byun <[email protected]>
+ * Yadwinder Singh Brar <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef __LINUX_MFD_MAX77686_PRIV_H
+#define __LINUX_MFD_MAX77686_PRIV_H
+
+#include <linux/i2c.h>
+
+#define MAX77686_REG_INVALID (0xff)
+#define RAMP_MASK (0xc0)
+#define CHIP_REV (0x03)
+
+enum max77686_pmic_reg {
+ MAX77686_REG_DEVICE_ID = 0x00,
+ MAX77686_REG_INTSRC = 0x01,
+ MAX77686_REG_INT1 = 0x02,
+ MAX77686_REG_INT2 = 0x03,
+
+ MAX77686_REG_INT1MSK = 0x04,
+ MAX77686_REG_INT2MSK = 0x05,
+
+ MAX77686_REG_STATUS1 = 0x06,
+ MAX77686_REG_STATUS2 = 0x07,
+
+ MAX77686_REG_PWRON = 0x08,
+ MAX77686_REG_ONOFF_DELAY = 0x09,
+ MAX77686_REG_MRSTB = 0x0A,
+ /* Reserved: 0x0B-0x0F */
+
+ MAX77686_REG_BUCK1CTRL = 0x10,
+ MAX77686_REG_BUCK1OUT = 0x11,
+ MAX77686_REG_BUCK2CTRL1 = 0x12,
+ MAX77686_REG_BUCK234FREQ = 0x13,
+ MAX77686_REG_BUCK2DVS1 = 0x14,
+ MAX77686_REG_BUCK2DVS2 = 0x15,
+ MAX77686_REG_BUCK2DVS3 = 0x16,
+ MAX77686_REG_BUCK2DVS4 = 0x17,
+ MAX77686_REG_BUCK2DVS5 = 0x18,
+ MAX77686_REG_BUCK2DVS6 = 0x19,
+ MAX77686_REG_BUCK2DVS7 = 0x1A,
+ MAX77686_REG_BUCK2DVS8 = 0x1B,
+ MAX77686_REG_BUCK3CTRL1 = 0x1C,
+ /* Reserved: 0x1D */
+ MAX77686_REG_BUCK3DVS1 = 0x1E,
+ MAX77686_REG_BUCK3DVS2 = 0x1F,
+ MAX77686_REG_BUCK3DVS3 = 0x20,
+ MAX77686_REG_BUCK3DVS4 = 0x21,
+ MAX77686_REG_BUCK3DVS5 = 0x22,
+ MAX77686_REG_BUCK3DVS6 = 0x23,
+ MAX77686_REG_BUCK3DVS7 = 0x24,
+ MAX77686_REG_BUCK3DVS8 = 0x25,
+ MAX77686_REG_BUCK4CTRL1 = 0x26,
+ /* Reserved: 0x27 */
+ MAX77686_REG_BUCK4DVS1 = 0x28,
+ MAX77686_REG_BUCK4DVS2 = 0x29,
+ MAX77686_REG_BUCK4DVS3 = 0x2A,
+ MAX77686_REG_BUCK4DVS4 = 0x2B,
+ MAX77686_REG_BUCK4DVS5 = 0x2C,
+ MAX77686_REG_BUCK4DVS6 = 0x2D,
+ MAX77686_REG_BUCK4DVS7 = 0x2E,
+ MAX77686_REG_BUCK4DVS8 = 0x2F,
+ MAX77686_REG_BUCK5CTRL = 0x30,
+ MAX77686_REG_BUCK5OUT = 0x31,
+ MAX77686_REG_BUCK6CTRL = 0x32,
+ MAX77686_REG_BUCK6OUT = 0x33,
+ MAX77686_REG_BUCK7CTRL = 0x34,
+ MAX77686_REG_BUCK7OUT = 0x35,
+ MAX77686_REG_BUCK8CTRL = 0x36,
+ MAX77686_REG_BUCK8OUT = 0x37,
+ MAX77686_REG_BUCK9CTRL = 0x38,
+ MAX77686_REG_BUCK9OUT = 0x39,
+ /* Reserved: 0x3A-0x3F */
+
+ MAX77686_REG_LDO1CTRL1 = 0x40,
+ MAX77686_REG_LDO2CTRL1 = 0x41,
+ MAX77686_REG_LDO3CTRL1 = 0x42,
+ MAX77686_REG_LDO4CTRL1 = 0x43,
+ MAX77686_REG_LDO5CTRL1 = 0x44,
+ MAX77686_REG_LDO6CTRL1 = 0x45,
+ MAX77686_REG_LDO7CTRL1 = 0x46,
+ MAX77686_REG_LDO8CTRL1 = 0x47,
+ MAX77686_REG_LDO9CTRL1 = 0x48,
+ MAX77686_REG_LDO10CTRL1 = 0x49,
+ MAX77686_REG_LDO11CTRL1 = 0x4A,
+ MAX77686_REG_LDO12CTRL1 = 0x4B,
+ MAX77686_REG_LDO13CTRL1 = 0x4C,
+ MAX77686_REG_LDO14CTRL1 = 0x4D,
+ MAX77686_REG_LDO15CTRL1 = 0x4E,
+ MAX77686_REG_LDO16CTRL1 = 0x4F,
+ MAX77686_REG_LDO17CTRL1 = 0x50,
+ MAX77686_REG_LDO18CTRL1 = 0x51,
+ MAX77686_REG_LDO19CTRL1 = 0x52,
+ MAX77686_REG_LDO20CTRL1 = 0x53,
+ MAX77686_REG_LDO21CTRL1 = 0x54,
+ MAX77686_REG_LDO22CTRL1 = 0x55,
+ MAX77686_REG_LDO23CTRL1 = 0x56,
+ MAX77686_REG_LDO24CTRL1 = 0x57,
+ MAX77686_REG_LDO25CTRL1 = 0x58,
+ MAX77686_REG_LDO26CTRL1 = 0x59,
+ /* Reserved: 0x5A-0x5F */
+ MAX77686_REG_LDO1CTRL2 = 0x60,
+ MAX77686_REG_LDO2CTRL2 = 0x61,
+ MAX77686_REG_LDO3CTRL2 = 0x62,
+ MAX77686_REG_LDO4CTRL2 = 0x63,
+ MAX77686_REG_LDO5CTRL2 = 0x64,
+ MAX77686_REG_LDO6CTRL2 = 0x65,
+ MAX77686_REG_LDO7CTRL2 = 0x66,
+ MAX77686_REG_LDO8CTRL2 = 0x67,
+ MAX77686_REG_LDO9CTRL2 = 0x68,
+ MAX77686_REG_LDO10CTRL2 = 0x69,
+ MAX77686_REG_LDO11CTRL2 = 0x6A,
+ MAX77686_REG_LDO12CTRL2 = 0x6B,
+ MAX77686_REG_LDO13CTRL2 = 0x6C,
+ MAX77686_REG_LDO14CTRL2 = 0x6D,
+ MAX77686_REG_LDO15CTRL2 = 0x6E,
+ MAX77686_REG_LDO16CTRL2 = 0x6F,
+ MAX77686_REG_LDO17CTRL2 = 0x70,
+ MAX77686_REG_LDO18CTRL2 = 0x71,
+ MAX77686_REG_LDO19CTRL2 = 0x72,
+ MAX77686_REG_LDO20CTRL2 = 0x73,
+ MAX77686_REG_LDO21CTRL2 = 0x74,
+ MAX77686_REG_LDO22CTRL2 = 0x75,
+ MAX77686_REG_LDO23CTRL2 = 0x76,
+ MAX77686_REG_LDO24CTRL2 = 0x77,
+ MAX77686_REG_LDO25CTRL2 = 0x78,
+ MAX77686_REG_LDO26CTRL2 = 0x79,
+ /* Reserved: 0x7A-0x7D */
+
+ MAX77686_REG_BBAT_CHG = 0x7E,
+ MAX77686_REG_32KHZ = 0x7F,
+
+ MAX77686_REG_PMIC_END = 0x80,
+};
+
+enum max77686_rtc_reg {
+ MAX77686_RTC_INT = 0x00,
+ MAX77686_RTC_INTM = 0x01,
+ MAX77686_RTC_CONTROLM = 0x02,
+ MAX77686_RTC_CONTROL = 0x03,
+ MAX77686_RTC_UPDATE0 = 0x04,
+ /* Reserved: 0x5 */
+ MAX77686_WTSR_SMPL_CNTL = 0x06,
+ MAX77686_RTC_SEC = 0x07,
+ MAX77686_RTC_MIN = 0x08,
+ MAX77686_RTC_HOUR = 0x09,
+ MAX77686_RTC_WEEKDAY = 0x0A,
+ MAX77686_RTC_MONTH = 0x0B,
+ MAX77686_RTC_YEAR = 0x0C,
+ MAX77686_RTC_DATE = 0x0D,
+ MAX77686_ALARM1_SEC = 0x0E,
+ MAX77686_ALARM1_MIN = 0x0F,
+ MAX77686_ALARM1_HOUR = 0x10,
+ MAX77686_ALARM1_WEEKDAY = 0x11,
+ MAX77686_ALARM1_MONTH = 0x12,
+ MAX77686_ALARM1_YEAR = 0x13,
+ MAX77686_ALARM1_DATE = 0x14,
+ MAX77686_ALARM2_SEC = 0x15,
+ MAX77686_ALARM2_MIN = 0x16,
+ MAX77686_ALARM2_HOUR = 0x17,
+ MAX77686_ALARM2_WEEKDAY = 0x18,
+ MAX77686_ALARM2_MONTH = 0x19,
+ MAX77686_ALARM2_YEAR = 0x1A,
+ MAX77686_ALARM2_DATE = 0x1B,
+};
+
+#define MAX77686_IRQSRC_PMIC (0)
+#define MAX77686_IRQSRC_RTC (1 << 0)
+
+enum max77686_irq_source {
+ PMIC_INT1 = 0,
+ PMIC_INT2,
+ RTC_INT,
+
+ MAX77686_IRQ_GROUP_NR,
+};
+
+enum max77686_irq {
+ MAX77686_PMICIRQ_PWRONF = 0,
+ MAX77686_PMICIRQ_PWRONR,
+ MAX77686_PMICIRQ_JIGONBF,
+ MAX77686_PMICIRQ_JIGONBR,
+ MAX77686_PMICIRQ_ACOKBF,
+ MAX77686_PMICIRQ_ACOKBR,
+ MAX77686_PMICIRQ_ONKEY1S,
+ MAX77686_PMICIRQ_MRSTB,
+
+ MAX77686_PMICIRQ_140C,
+ MAX77686_PMICIRQ_120C,
+
+ MAX77686_RTCIRQ_RTC60S = 16,
+ MAX77686_RTCIRQ_RTCA1,
+ MAX77686_RTCIRQ_RTCA2,
+ MAX77686_RTCIRQ_SMPL,
+ MAX77686_RTCIRQ_RTC1S,
+ MAX77686_RTCIRQ_WTSR,
+
+ MAX77686_IRQ_NR,
+};
+
+struct max77686_dev {
+ struct device *dev;
+ struct i2c_client *i2c; /* 0xcc / PMIC, Battery Control, and FLASH */
+ struct i2c_client *rtc; /* slave addr 0x0c */
+ struct regmap *regmap;
+ struct regmap *rtc_regmap;
+ int type;
+ int irq;
+ struct mutex irqlock;
+ int irq_masks_cur[MAX77686_IRQ_GROUP_NR];
+ int irq_masks_cache[MAX77686_IRQ_GROUP_NR];
+ struct irq_domain *irq_domain;
+ struct max77686_platform_data *pdata;
+};
+
+extern int max77686_irq_init(struct max77686_dev *max77686);
+extern void max77686_irq_exit(struct max77686_dev *max77686);
+extern int max77686_irq_resume(struct max77686_dev *max77686);
+
+extern int max77686_read_reg(struct i2c_client *i2c, int reg, int *dest);
+extern int max77686_bulk_read(struct i2c_client *i2c, int reg, int count,
+ int *buf);
+extern int max77686_write_reg(struct i2c_client *i2c, int reg, int value);
+extern int max77686_bulk_write(struct i2c_client *i2c, int reg, int count,
+ int *buf);
+extern int max77686_update_reg(struct i2c_client *i2c, int reg, int val,
+ int mask);
+
+extern int max77686_debug_mask; /* enables debug prints */
+
+enum {
+ MAX77686_DEBUG_INFO = 1 << 0,
+ MAX77686_DEBUG_MASK = 1 << 1,
+ MAX77686_DEBUG_INT = 1 << 2,
+};
+
+#ifndef CONFIG_DEBUG_MAX77686
+
+#define dbg_mask(fmt, ...) do { } while (0)
+#define dbg_info(fmt, ...) do { } while (0)
+#define dbg_int(fmt, ...) do { } while (0)
+
+#else
+
+#define dbg_mask(fmt, ...) \
+do { \
+ if (max77686_debug_mask & MAX77686_DEBUG_MASK) \
+ printk(KERN_INFO pr_fmt(fmt), ##__VA_ARGS__); \
+} while (0)
+
+#define dbg_info(fmt, ...) \
+do { \
+ if (max77686_debug_mask & MAX77686_DEBUG_INFO) \
+ printk(KERN_INFO pr_fmt(fmt), ##__VA_ARGS__); \
+} while (0)
+
+#define dbg_int(fmt, ...) \
+do { \
+ if (max77686_debug_mask & MAX77686_DEBUG_INT) \
+ printk(KERN_INFO pr_fmt(fmt), ##__VA_ARGS__); \
+} while (0)
+#endif /* DEBUG_MAX77686 */
+
+#endif /* __LINUX_MFD_MAX77686_PRIV_H */
diff --git a/include/linux/mfd/max77686.h b/include/linux/mfd/max77686.h
new file mode 100644
index 0000000..104cc82
--- /dev/null
+++ b/include/linux/mfd/max77686.h
@@ -0,0 +1,100 @@
+/*
+ * max77686.h - Driver for the Maxim 77686
+ *
+ * Copyright (C) 2011 Samsung Electrnoics
+ * Chiwoong Byun <[email protected]>
+ * Yadwinder Singh Brar <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ * This driver is based on max8997.h
+ *
+ * MAX77686 has PMIC, RTC devices.
+ * The devices share the same I2C bus and included in
+ * this mfd driver.
+ */
+
+#ifndef __LINUX_MFD_MAX77686_H
+#define __LINUX_MFD_MAX77686_H
+
+#include <linux/regulator/consumer.h>
+#include <linux/regulator/of_regulator.h>
+
+/* MAX77686 regulator IDs */
+enum max77686_regulators {
+ MAX77686_LDO1 = 0,
+ MAX77686_LDO2,
+ MAX77686_LDO3,
+ MAX77686_LDO4,
+ MAX77686_LDO5,
+ MAX77686_LDO6,
+ MAX77686_LDO7,
+ MAX77686_LDO8,
+ MAX77686_LDO9,
+ MAX77686_LDO10,
+ MAX77686_LDO11,
+ MAX77686_LDO12,
+ MAX77686_LDO13,
+ MAX77686_LDO14,
+ MAX77686_LDO15,
+ MAX77686_LDO16,
+ MAX77686_LDO17,
+ MAX77686_LDO18,
+ MAX77686_LDO19,
+ MAX77686_LDO20,
+ MAX77686_LDO21,
+ MAX77686_LDO22,
+ MAX77686_LDO23,
+ MAX77686_LDO24,
+ MAX77686_LDO25,
+ MAX77686_LDO26,
+ MAX77686_BUCK1,
+ MAX77686_BUCK2,
+ MAX77686_BUCK3,
+ MAX77686_BUCK4,
+ MAX77686_BUCK5,
+ MAX77686_BUCK6,
+ MAX77686_BUCK7,
+ MAX77686_BUCK8,
+ MAX77686_BUCK9,
+ MAX77686_EN32KHZ_AP,
+ MAX77686_EN32KHZ_CP,
+ MAX77686_P32KH,
+
+ MAX77686_REG_MAX,
+};
+
+enum max77686_ramp_rate {
+ MAX77686_RAMP_RATE_13MV = 1,
+ MAX77686_RAMP_RATE_27MV, /* default */
+ MAX77686_RAMP_RATE_55MV,
+ MAX77686_RAMP_RATE_100MV,
+};
+
+struct max77686_platform_data {
+ bool wakeup;
+ u8 ramp_delay;
+ struct of_regulator_match *regulators;
+ int num_regulators;
+ struct max77686_opmode_data *opmode_data;
+
+ /*
+ * GPIO-DVS feature is not enabled with the current version of
+ * MAX77686 driver. Buck2/3/4_voltages[0] is used as the default
+ * voltage at probe.
+ */
+};
+
+#endif /* __LINUX_MFD_MAX77686_H */
--
1.7.0.4
Add support for PMIC/regulator portion of MAX77686 multifunction device.
MAX77686 provides LDOs[1-26] and BUCKs[1-9]. This is initial release of driver
which supports setting and getting the voltage of a regulator with I2C
interface.
Signed-off-by: Yadwinder Singh Brar <[email protected]>
---
drivers/regulator/Kconfig | 9 +
drivers/regulator/Makefile | 1 +
drivers/regulator/max77686.c | 512 ++++++++++++++++++++++++++++++++++++++++++
3 files changed, 522 insertions(+), 0 deletions(-)
create mode 100644 drivers/regulator/max77686.c
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 4ad4e8d..a41d2cf 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -195,6 +195,15 @@ config REGULATOR_MAX8998
via I2C bus. The provided regulator is suitable for S3C6410
and S5PC1XX chips to control VCC_CORE and VCC_USIM voltages.
+config REGULATOR_MAX77686
+ tristate "Maxim 77686 regulator"
+ depends on MFD_MAX77686
+ help
+ This driver controls a Maxim 77686 voltage regulator via I2C
+ bus. The provided regulator is suitable for Exynos5 chips to
+ control VDD_ARM and VDD_INT voltages.It supports LDOs[1-26]
+ and BUCKs[1-9].
+
config REGULATOR_PCAP
tristate "Motorola PCAP2 regulator driver"
depends on EZX_PCAP
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index dcc56dc..949b1f2 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -30,6 +30,7 @@ obj-$(CONFIG_REGULATOR_MAX8925) += max8925-regulator.o
obj-$(CONFIG_REGULATOR_MAX8952) += max8952.o
obj-$(CONFIG_REGULATOR_MAX8997) += max8997.o
obj-$(CONFIG_REGULATOR_MAX8998) += max8998.o
+obj-$(CONFIG_REGULATOR_MAX77686) += max77686.o
obj-$(CONFIG_REGULATOR_MC13783) += mc13783-regulator.o
obj-$(CONFIG_REGULATOR_MC13892) += mc13892-regulator.o
obj-$(CONFIG_REGULATOR_MC13XXX_CORE) += mc13xxx-regulator-core.o
diff --git a/drivers/regulator/max77686.c b/drivers/regulator/max77686.c
new file mode 100644
index 0000000..7379c29
--- /dev/null
+++ b/drivers/regulator/max77686.c
@@ -0,0 +1,512 @@
+/*
+ * max77686.c - Regulator driver for the Maxim 77686
+ *
+ * Copyright (C) 2012 Samsung Electronics Co. Ltd.
+ * Chiwoong Byun <[email protected]>
+ * Yadwinder Singh Brar <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ * This driver is based on max8997.c
+ */
+
+#include <linux/module.h>
+#include <linux/bug.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/gpio.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/of_regulator.h>
+#include <linux/mfd/max77686.h>
+#include <linux/mfd/max77686-private.h>
+
+#define RAMP_VALUE (max77686->ramp_delay << 6)
+
+struct max77686_data {
+ struct device *dev;
+ struct max77686_dev *iodev;
+ int num_regulators;
+ struct regulator_dev **rdev;
+ int ramp_delay; /* index of ramp_delay */
+
+ /*GPIO-DVS feature is not enabled with the
+ *current version of MAX77686 driver.*/
+};
+
+static int max77686_get_enable_register(struct regulator_dev *rdev,
+ int *reg, int *mask, int *pattern)
+{
+ int rid = rdev_get_id(rdev);
+
+ switch (rid) {
+ case MAX77686_LDO1...MAX77686_LDO26:
+ *reg = MAX77686_REG_LDO1CTRL1 + (rid - MAX77686_LDO1);
+ *mask = 0xc0;
+ *pattern = 0xc0;
+ break;
+ case MAX77686_BUCK1:
+ *reg = MAX77686_REG_BUCK1CTRL;
+ *mask = 0x03;
+ *pattern = 0x03;
+ break;
+ case MAX77686_BUCK2:
+ *reg = MAX77686_REG_BUCK2CTRL1;
+ *mask = 0x30;
+ *pattern = 0x10;
+ break;
+ case MAX77686_BUCK3:
+ *reg = MAX77686_REG_BUCK3CTRL1;
+ *mask = 0x30;
+ *pattern = 0x10;
+ break;
+ case MAX77686_BUCK4:
+ *reg = MAX77686_REG_BUCK4CTRL1;
+ *mask = 0x30;
+ *pattern = 0x10;
+ break;
+ case MAX77686_BUCK5...MAX77686_BUCK9:
+ *reg = MAX77686_REG_BUCK5CTRL + (rid - MAX77686_BUCK5) * 2;
+ *mask = 0x03;
+ *pattern = 0x03;
+ break;
+ default:
+ /* Not controllable or not exists */
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int max77686_reg_is_enabled(struct regulator_dev *rdev)
+{
+ struct max77686_data *max77686 = rdev_get_drvdata(rdev);
+ struct i2c_client *i2c = max77686->iodev->i2c;
+ int ret, reg, mask, pattern;
+ int val;
+
+ ret = max77686_get_enable_register(rdev, ®, &mask, &pattern);
+ if (ret)
+ return ret;
+
+ ret = max77686_read_reg(i2c, reg, &val);
+ if (ret)
+ return ret;
+
+ return (val & mask) == pattern;
+}
+
+static int max77686_reg_enable(struct regulator_dev *rdev)
+{
+ struct max77686_data *max77686 = rdev_get_drvdata(rdev);
+ struct i2c_client *i2c = max77686->iodev->i2c;
+ int ret, reg, mask, pattern;
+
+ ret = max77686_get_enable_register(rdev, ®, &mask, &pattern);
+ if (ret)
+ return ret;
+
+ return max77686_update_reg(i2c, reg, pattern, mask);
+}
+
+static int max77686_reg_disable(struct regulator_dev *rdev)
+{
+ struct max77686_data *max77686 = rdev_get_drvdata(rdev);
+ struct i2c_client *i2c = max77686->iodev->i2c;
+ int ret, reg, mask, pattern;
+
+ ret = max77686_get_enable_register(rdev, ®, &mask, &pattern);
+ if (ret)
+ return ret;
+
+ return max77686_update_reg(i2c, reg, ~mask, mask);
+}
+
+static int max77686_get_voltage_register(struct regulator_dev *rdev,
+ int *_reg, int *_shift, int *_mask)
+{
+ int rid = rdev_get_id(rdev);
+ int reg, shift = 0, mask = 0x3f;
+
+ switch (rid) {
+ case MAX77686_LDO1...MAX77686_LDO26:
+ reg = MAX77686_REG_LDO1CTRL1 + (rid - MAX77686_LDO1);
+ break;
+ case MAX77686_BUCK1:
+ reg = MAX77686_REG_BUCK1OUT;
+ break;
+ case MAX77686_BUCK2:
+ reg = MAX77686_REG_BUCK2DVS1;
+ mask = 0xff;
+ break;
+ case MAX77686_BUCK3:
+ reg = MAX77686_REG_BUCK3DVS1;
+ mask = 0xff;
+ break;
+ case MAX77686_BUCK4:
+ reg = MAX77686_REG_BUCK4DVS1;
+ mask = 0xff;
+ break;
+ case MAX77686_BUCK5...MAX77686_BUCK9:
+ reg = MAX77686_REG_BUCK5OUT + (rid - MAX77686_BUCK5) * 2;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ *_reg = reg;
+ *_shift = shift;
+ *_mask = mask;
+
+ return 0;
+}
+
+static int max77686_get_voltage_sel(struct regulator_dev *rdev)
+{
+ struct max77686_data *max77686 = rdev_get_drvdata(rdev);
+ struct i2c_client *i2c = max77686->iodev->i2c;
+ int reg, shift, mask, ret;
+ int val;
+
+ ret = max77686_get_voltage_register(rdev, ®, &shift, &mask);
+ if (ret)
+ return ret;
+
+ ret = max77686_read_reg(i2c, reg, &val);
+ if (ret)
+ return ret;
+
+ val >>= shift;
+ val &= mask;
+
+ return val;
+}
+
+static int max77686_set_voltage_sel(struct regulator_dev *rdev,
+ unsigned sel)
+{
+ struct max77686_data *max77686 = rdev_get_drvdata(rdev);
+ struct i2c_client *i2c = max77686->iodev->i2c;
+ int reg, shift = 0, mask, ret;
+
+ ret = max77686_get_voltage_register(rdev, ®, &shift, &mask);
+ if (ret)
+ return ret;
+
+ ret = max77686_update_reg(i2c, reg, sel << shift, mask << shift);
+
+ return ret;
+}
+
+static int max77686_voltage_buck_time_sel(struct regulator_dev *rdev,
+ unsigned int old_sel,
+ unsigned int new_sel)
+{
+ struct max77686_data *max77686 = rdev_get_drvdata(rdev);
+ int ramp[] = {13, 27, 55, 100}; /* ramp_rate in mV/uS */
+
+ return DIV_ROUND_UP(rdev->desc->uV_step *
+ abs(new_sel - old_sel),
+ ramp[max77686->ramp_delay]);
+}
+
+static struct regulator_ops max77686_ops = {
+ .map_voltage = regulator_map_voltage_linear,
+ .list_voltage = regulator_list_voltage_linear,
+ .is_enabled = max77686_reg_is_enabled,
+ .enable = max77686_reg_enable,
+ .disable = max77686_reg_disable,
+ .get_voltage_sel = max77686_get_voltage_sel,
+ .set_voltage_sel = max77686_set_voltage_sel,
+};
+
+static struct regulator_ops max77686_buck_ops = {
+ .map_voltage = regulator_map_voltage_linear,
+ .list_voltage = regulator_list_voltage_linear,
+ .is_enabled = max77686_reg_is_enabled,
+ .enable = max77686_reg_enable,
+ .disable = max77686_reg_disable,
+ .get_voltage_sel = max77686_get_voltage_sel,
+ .set_voltage_sel = max77686_set_voltage_sel,
+ .set_voltage_time_sel = max77686_voltage_buck_time_sel,
+};
+
+#define regulator_desc_ldo(num) { \
+ .name = "LDO"#num, \
+ .id = MAX77686_LDO##num, \
+ .n_voltages = 64, \
+ .ops = &max77686_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .owner = THIS_MODULE, \
+ .min_uV = 800000, \
+ .uV_step = 50000 \
+}
+#define regulator_desc_ldo_low_vol(num) { \
+ .name = "LDO"#num, \
+ .id = MAX77686_LDO##num, \
+ .ops = &max77686_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .owner = THIS_MODULE, \
+ .min_uV = 800000, \
+ .uV_step = 25000, \
+ .n_voltages = 64 \
+}
+#define regulator_desc_buck(num) { \
+ .name = "BUCK"#num, \
+ .id = MAX77686_BUCK##num, \
+ .ops = &max77686_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .owner = THIS_MODULE, \
+ .min_uV = 750000, \
+ .uV_step = 50000, \
+ .n_voltages = 64 \
+}
+#define regulator_desc_buck_dvs(num) { \
+ .name = "BUCK"#num, \
+ .id = MAX77686_BUCK##num, \
+ .ops = &max77686_buck_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .owner = THIS_MODULE, \
+ .min_uV = 600000, \
+ .uV_step = 12500, \
+ .n_voltages = 256 \
+}
+
+static struct regulator_desc regulators[] = {
+ regulator_desc_ldo_low_vol(1),
+ regulator_desc_ldo_low_vol(2),
+ regulator_desc_ldo(3),
+ regulator_desc_ldo(4),
+ regulator_desc_ldo(5),
+ regulator_desc_ldo_low_vol(6),
+ regulator_desc_ldo_low_vol(7),
+ regulator_desc_ldo_low_vol(8),
+ regulator_desc_ldo(9),
+ regulator_desc_ldo(10),
+ regulator_desc_ldo(11),
+ regulator_desc_ldo(12),
+ regulator_desc_ldo(13),
+ regulator_desc_ldo(14),
+ regulator_desc_ldo(15),
+ regulator_desc_ldo(16),
+ regulator_desc_ldo(17),
+ regulator_desc_ldo(18),
+ regulator_desc_ldo(19),
+ regulator_desc_ldo(20),
+ regulator_desc_ldo(21),
+ regulator_desc_ldo(22),
+ regulator_desc_ldo(23),
+ regulator_desc_ldo(24),
+ regulator_desc_ldo(25),
+ regulator_desc_ldo(26),
+ regulator_desc_buck(1),
+ regulator_desc_buck_dvs(2),
+ regulator_desc_buck_dvs(3),
+ regulator_desc_buck_dvs(4),
+ regulator_desc_buck(5),
+ regulator_desc_buck(6),
+ regulator_desc_buck(7),
+ regulator_desc_buck(8),
+ regulator_desc_buck(9),
+};
+
+#ifdef CONFIG_OF
+static int max77686_pmic_dt_parse_pdata(struct max77686_dev *iodev,
+ struct max77686_platform_data *pdata)
+{
+ struct device_node *pmic_np, *regulators_np;
+ struct of_regulator_match *rdata;
+ unsigned int i, ret;
+
+ pmic_np = iodev->dev->of_node;
+ if (!pmic_np) {
+ dev_err(iodev->dev, "could not find pmic sub-node\n");
+ return -ENODEV;
+ }
+
+ regulators_np = of_find_node_by_name(pmic_np, "voltage-regulators");
+ if (!regulators_np) {
+ dev_err(iodev->dev, "could not find regulators sub-node\n");
+ return -EINVAL;
+ }
+
+ /* count the number of regulators to be supported in pmic */
+ pdata->num_regulators = ARRAY_SIZE(regulators);
+
+ rdata = devm_kzalloc(iodev->dev, sizeof(*rdata) *
+ (pdata->num_regulators), GFP_KERNEL);
+ if (!rdata) {
+ dev_err(iodev->dev,
+ "could not allocate memory for regulator data\n");
+ return -ENOMEM;
+ }
+
+ for (i = 0; i < pdata->num_regulators; i++)
+ rdata[i].name = regulators[i].name;
+
+ ret = of_regulator_match(iodev->dev, regulators_np, rdata,
+ pdata->num_regulators);
+
+ if (ret < 0)
+ dev_err(iodev->dev, "Parsing DT for regulators failed\n");
+ else
+ dev_info(iodev->dev, "regulators found in device tree : %d\n"
+ , ret);
+
+ pdata->regulators = rdata;
+
+ if (of_property_read_u32(pmic_np, "max77686,buck_ramp_delay", &i))
+ pdata->ramp_delay = i & 0xff;
+
+ return 0;
+}
+#else
+static int max77686_pmic_dt_parse_pdata(struct max77686_dev *iodev,
+ struct max77686_platform_data *pdata)
+{
+ return 0;
+}
+#endif /* CONFIG_OF */
+
+static __devinit int max77686_pmic_probe(struct platform_device *pdev)
+{
+ struct max77686_dev *iodev = dev_get_drvdata(pdev->dev.parent);
+ struct max77686_platform_data *pdata = iodev->pdata;
+ struct regulator_dev **rdev;
+ struct max77686_data *max77686;
+ struct i2c_client *i2c = iodev->i2c;
+ struct regulator_config config = { };
+ int i, ret, size;
+
+ if (iodev->dev->of_node) {
+ ret = max77686_pmic_dt_parse_pdata(iodev, pdata);
+ if (ret)
+ return ret;
+ } else { /* pdata from machine-setup file */
+ if (!pdata) {
+ dev_err(&pdev->dev, "platform data not found\n");
+ return -ENODEV;
+ } else {
+ if (pdata->num_regulators != ARRAY_SIZE(regulators)) {
+ dev_err(&pdev->dev,
+ "incomplete regulator list\n");
+ return -ENODEV;
+ }
+ }
+ }
+
+ max77686 = devm_kzalloc(&pdev->dev, sizeof(struct max77686_data),
+ GFP_KERNEL);
+ if (!max77686)
+ return -ENOMEM;
+
+ size = sizeof(struct regulator_dev *) * pdata->num_regulators;
+ max77686->rdev = devm_kzalloc(&pdev->dev, size, GFP_KERNEL);
+ if (!max77686->rdev) {
+ kfree(max77686);
+ return -ENOMEM;
+ }
+
+ rdev = max77686->rdev;
+
+ max77686->dev = &pdev->dev;
+ max77686->iodev = iodev;
+ max77686->num_regulators = pdata->num_regulators;
+
+ if (pdata->ramp_delay < MAX77686_RAMP_RATE_13MV ||
+ pdata->ramp_delay > MAX77686_RAMP_RATE_100MV)
+ pdata->ramp_delay = MAX77686_RAMP_RATE_27MV; /* default */
+
+ max77686->ramp_delay = pdata->ramp_delay - 1;
+ max77686_update_reg(i2c, MAX77686_REG_BUCK2CTRL1,
+ RAMP_VALUE, RAMP_MASK);
+ max77686_update_reg(i2c, MAX77686_REG_BUCK3CTRL1,
+ RAMP_VALUE, RAMP_MASK);
+ max77686_update_reg(i2c, MAX77686_REG_BUCK4CTRL1,
+ RAMP_VALUE, RAMP_MASK);
+
+ platform_set_drvdata(pdev, max77686);
+
+ for (i = 0; i < pdata->num_regulators; i++) {
+ config.dev = max77686->dev;
+ config.init_data = pdata->regulators[i].init_data;
+ config.driver_data = max77686;
+
+ rdev[i] = regulator_register(®ulators[i], &config);
+ if (IS_ERR(rdev[i])) {
+ ret = PTR_ERR(rdev[i]);
+ dev_err(max77686->dev,
+ "regulator init failed for id : %d\n", i);
+ rdev[i] = NULL;
+ goto err;
+ }
+ }
+
+ return 0;
+ err:
+ for (i = 0; i < max77686->num_regulators; i++)
+ if (rdev[i])
+ regulator_unregister(rdev[i]);
+
+ return ret;
+}
+
+static int __devexit max77686_pmic_remove(struct platform_device *pdev)
+{
+ struct max77686_data *max77686 = platform_get_drvdata(pdev);
+ struct regulator_dev **rdev = max77686->rdev;
+ int i;
+
+ for (i = 0; i < max77686->num_regulators; i++)
+ if (rdev[i])
+ regulator_unregister(rdev[i]);
+
+ return 0;
+}
+
+static const struct platform_device_id max77686_pmic_id[] = {
+ {"max77686-pmic", 0},
+ {},
+};
+MODULE_DEVICE_TABLE(platform, max77686_pmic_id);
+
+static struct platform_driver max77686_pmic_driver = {
+ .driver = {
+ .name = "max77686-pmic",
+ .owner = THIS_MODULE,
+ },
+ .probe = max77686_pmic_probe,
+ .remove = __devexit_p(max77686_pmic_remove),
+ .id_table = max77686_pmic_id,
+};
+
+static int __init max77686_pmic_init(void)
+{
+ return platform_driver_register(&max77686_pmic_driver);
+}
+subsys_initcall(max77686_pmic_init);
+
+static void __exit max77686_pmic_cleanup(void)
+{
+ platform_driver_unregister(&max77686_pmic_driver);
+}
+module_exit(max77686_pmic_cleanup);
+
+MODULE_DESCRIPTION("MAXIM 77686 Regulator Driver");
+MODULE_AUTHOR("Chiwoong Byun <[email protected]>");
+MODULE_AUTHOR("Yadwinder Singh Brar <[email protected]>");
+MODULE_LICENSE("GPL");
--
1.7.0.4
On Thu, May 17, 2012 at 07:09:26PM +0530, Yadwinder Singh Brar wrote:
> MAX77686 is a mulitifunction device with PMIC, RTC and Charger on chip. This
> driver provides common support for accessing the device. This is initial
> version of this driver that supports to enable the chip with its primary I2C
> bus.It also includes IRQ and device tree support for MAX77686 chip.
Reviwed-by: Mark Brown <[email protected]>
On Thu, May 17, 2012 at 07:09:27PM +0530, Yadwinder Singh Brar wrote:
Looks mostly good. A couple of fairly small things:
> +static int max77686_get_voltage_sel(struct regulator_dev *rdev)
> +{
This looks like it should be regulator_get_voltage_sel_regmap().
> +static int max77686_set_voltage_sel(struct regulator_dev *rdev,
> + unsigned sel)
> +{
This looks like it should be regulator_set_voltage_sel_regmap().
> + max77686->ramp_delay = pdata->ramp_delay - 1;
> + max77686_update_reg(i2c, MAX77686_REG_BUCK2CTRL1,
> + RAMP_VALUE, RAMP_MASK);
> + max77686_update_reg(i2c, MAX77686_REG_BUCK3CTRL1,
> + RAMP_VALUE, RAMP_MASK);
> + max77686_update_reg(i2c, MAX77686_REG_BUCK4CTRL1,
> + RAMP_VALUE, RAMP_MASK);
This code is unclear because RAMP_VALUE looks like a constant that has
nothing to do with ramp_delay when in fact it's actually this:
> +#define RAMP_VALUE (max77686->ramp_delay << 6)
which isn't constant - this is why I queried this last time. Just
remove the define and write this out directly. The way the code is
written at the minute it looks like ramp_delay is just stored and not
referred to unless you go searching around the rest of the driver.
Hi Mark,
On Sun, May 20, 2012 at 3:30 PM, Mark Brown
<[email protected]> wrote:
> On Thu, May 17, 2012 at 07:09:27PM +0530, Yadwinder Singh Brar wrote:
>
> Looks mostly good. ?A couple of fairly small things:
>
>> +static int max77686_get_voltage_sel(struct regulator_dev *rdev)
>> +{
>
> This looks like it should be regulator_get_voltage_sel_regmap().
>
>> +static int max77686_set_voltage_sel(struct regulator_dev *rdev,
>> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? unsigned sel)
>> +{
>
> This looks like it should be regulator_set_voltage_sel_regmap().
>
Yes, We can use regulator_set_voltage_sel_regmap(), I will replace it.
>> + ? ? max77686->ramp_delay = pdata->ramp_delay - 1;
>> + ? ? max77686_update_reg(i2c, MAX77686_REG_BUCK2CTRL1,
>> + ? ? ? ? ? ? RAMP_VALUE, RAMP_MASK);
>> + ? ? max77686_update_reg(i2c, MAX77686_REG_BUCK3CTRL1,
>> + ? ? ? ? ? ? RAMP_VALUE, RAMP_MASK);
>> + ? ? max77686_update_reg(i2c, MAX77686_REG_BUCK4CTRL1,
>> + ? ? ? ? ? ? RAMP_VALUE, RAMP_MASK);
>
> This code is unclear because RAMP_VALUE looks like a constant that has
> nothing to do with ramp_delay when in fact it's actually this:
>
>> +#define RAMP_VALUE (max77686->ramp_delay << 6)
>
> which isn't constant - this is why I queried this last time. ?Just
> remove the define and write this out directly. ?The way the code is
> written at the minute it looks like ramp_delay is just stored and not
> referred to unless you go searching around the rest of the driver.
Ok, I will remove it.
Thanks,
Yadwinder.