On Sun, Apr 08, 2012 at 12:51:30PM +0100, Kamil Grzebien wrote:
> I've attached logs as you asked for. It was done on kernel 3.3.0-4.fc16.i686.
Below are iomem and dmesg diffs between bad and good (noapic) case. In
dmesg I only see this suspicious difference:
-system 00:0c: [mem 0xfec00000-0xfec0ffff] could not be reserved
+system 00:0c: [mem 0xfec00000-0xfec0ffff] has been reserved
but this is for "pnp 00:0c" not for iwl3945 which has f1eff000-f1efffff
addresses. So I have no idea why IO memory is not correcly mapped
for iwl3945. Any chance that pci folks could look on that? Here is mail
thread with previous information:
https://lkml.org/lkml/2012/3/11/112
Stanislaw
iomem.diff:
-----------
--- bad/iomem.log 2012-04-08 13:43:00.000000000 +0200
+++ good/iomem_noapic.log 2012-04-08 13:43:00.000000000 +0200
@@ -21,8 +21,8 @@ e0000000-f7ffffff : PCI Bus 0000:00
f0200000-f03fffff : PCI Bus 0000:0b
f0400000-f05fffff : PCI Bus 0000:09
f1b00000-f1bfffff : PCI Bus 0000:03
- f1bff400-f1bff4ff : 0000:03:09.1
- f1bff400-f1bff4ff : mmc0
+ f1bff500-f1bff5ff : 0000:03:09.1
+ f1bff500-f1bff5ff : mmc0
f1bff600-f1bff6ff : 0000:03:09.2
f1bff600-f1bff6ff : r592
f1bff700-f1bff7ff : 0000:03:09.3
@@ -32,6 +32,7 @@ e0000000-f7ffffff : PCI Bus 0000:00
f1c00000-f1dfffff : PCI Bus 0000:0c
f1e00000-f1efffff : PCI Bus 0000:0b
f1eff000-f1efffff : 0000:0b:00.0
+ f1eff000-f1efffff : iwl3945
f1f00000-f1ffffff : PCI Bus 0000:09
f1ffc000-f1ffffff : 0000:09:00.0
f1ffc000-f1ffffff : sky2
@@ -49,7 +50,7 @@ f8000000-fbffffff : PCI MMCONFIG 0000 [b
f8000000-fbffffff : pnp 00:0c
fc000000-febfffff : PCI Bus 0000:00
fec00000-fec0ffff : reserved
- fec00000-fec003ff : IOAPIC 0
+ fec00000-fec0ffff : pnp 00:0c
fec10000-fecfffff : PCI Bus 0000:00
fed00000-fed003ff : HPET 0
fed00000-fed003ff : pnp 00:09
dmesg.diff:
-----------
--- bad/dmesg.log 2012-05-28 15:12:13.559424823 +0200
+++ good/dmesg_noapic.log 2012-05-28 15:12:19.016266833 +0200
@@ -101,17 +101,11 @@ enabled)
enabled)
high edge lint[0x1])
high edge lint[0x1])
-gsi_base[0])
-IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
-ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
-ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
-ACPI: IRQ0 used by override.
-ACPI: IRQ2 used by override.
-ACPI: IRQ9 used by override.
-Using ACPI (MADT) for SMP configuration information
+ACPI: Skipping IOAPIC probe due to 'noapic' option.
+Using ACPI for processor (LAPIC) configuration information
ACPI: HPET id: 0x8086a201 base: 0xfed00000
SMP: Allowing 2 CPUs, 0 hotplug CPUs
-nr_irqs_gsi: 40
+nr_irqs_gsi: 16
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 0000000000100000
Allocating PCI resources starting at e0000000 (gap: e0000000:18000000)
@@ -121,7 +115,7 @@ PERCPU: Embedded 13 pages/cpu @f3c00000
pcpu-alloc: s31168 r0 d22080 u2097152 alloc=1*4194304
0 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 909828
-Kernel command line: BOOT_IMAGE=/vmlinuz-3.3.0-4.fc16.i686 root=UUID=7417d839-a647-466e-b57d-fc65d20a6342 ro rd.md=0 rd.lvm=0 rd.dm=0 quiet SYSFONT=latarcyrheb-sun16 rhgb rd.luks=0 KEYTABLE=pl2 LANG=en_US.UTF-8
+Kernel command line: BOOT_IMAGE=/vmlinuz-3.3.0-4.fc16.i686 root=UUID=7417d839-a647-466e-b57d-fc65d20a6342 ro rd.md=0 rd.lvm=0 rd.dm=0 quiet SYSFONT=latarcyrheb-sun16 rhgb rd.luks=0 KEYTABLE=pl2 LANG=en_US.UTF-8 noapic
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
@@ -142,15 +136,15 @@ Checking if this processor honours the W
SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
RCU dyntick-idle grace-period acceleration is enabled.
-NR_IRQS:2304 nr_irqs:512 16
+NR_IRQS:2304 nr_irqs:288 16
CPU 0 irqstacks, hard=f3008000 soft=f300a000
Extended CMOS year: 2000
Console: colour dummy device 80x25
enabled
hpet clockevent registered
Fast TSC calibration using PIT
-Detected 2394.148 MHz processor.
-Calibrating delay loop (skipped), value calculated using timer frequency.. 4788.29 BogoMIPS (lpj=2394148)
+Detected 2393.887 MHz processor.
+Calibrating delay loop (skipped), value calculated using timer frequency.. 4787.77 BogoMIPS (lpj=2393887)
pid_max: default: 32768 minimum: 301
Security Framework initialized
SELinux: Initializing.
@@ -169,9 +163,9 @@ mce: CPU supports 6 MCE banks
CPU0: Thermal monitoring enabled (TM2)
using mwait in idle threads.
ACPI: Core revision 20120111
+ACPI: setting ELCR to 0200 (from 0ea0)
ftrace: allocating 21899 entries in 43 pages
-Enabling APIC mode: Flat. Using 1 I/O APICs
-..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
+Enabling APIC mode: Flat. Using 0 I/O APICs
CPU0: Intel(R) Core(TM)2 Duo CPU T8300 @ 2.40GHz stepping 06
Performance Events: PEBS fmt0+, Core2 events, Intel PMU driver.
... version: 2
@@ -188,10 +182,10 @@ smpboot cpu 1: start_ip = 9b000
Initializing CPU#1
NMI watchdog enabled, takes one hw-pmu counter.
Brought up 2 CPUs
-Total of 2 processors activated (9576.59 BogoMIPS).
+Total of 2 processors activated (9575.54 BogoMIPS).
devtmpfs: initialized
atomic64 test passed for i586+ platform with CX8 and with SSE
-RTC time: 12:29:27, date: 04/08/12
+RTC time: 12:34:58, date: 04/08/12
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
@@ -219,7 +213,7 @@ ACPI: Dynamic OEM Table Load:
ACPI: SSDT (null) 00085 (v01 PmRef Cpu1Cst 00003000 INTL 20050624)
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
-ACPI: Using IOAPIC for interrupt routing
+ACPI: Using PIC for interrupt routing
ACPI: No dock devices found.
PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
(domain 0000 [bus 00-ff])
@@ -330,13 +324,11 @@ pci 0000:00:1c.4: bridge window [io 0
pci 0000:00:1c.4: bridge window [mem 0xf1c00000-0xf1dfffff]
pci 0000:00:1c.4: bridge window [mem 0xf0000000-0xf01fffff 64bit pref]
type 0 class 0x000c00
-pci 0000:03:09.0: proprietary Ricoh MMC controller disabled (via firewire function)
-pci 0000:03:09.0: MMC cards are now supported by standard SDHCI controller
pci 0000:03:09.0: reg 10: [mem 0xf1bff800-0xf1bfffff]
pci 0000:03:09.0: supports D1 D2
pci 0000:03:09.0: PME# supported from D0 D1 D2 D3hot D3cold
type 0 class 0x000805
-pci 0000:03:09.1: reg 10: [mem 0xf1bff400-0xf1bff4ff]
+pci 0000:03:09.1: reg 10: [mem 0xf1bff500-0xf1bff5ff]
pci 0000:03:09.1: supports D1 D2
pci 0000:03:09.1: PME# supported from D0 D1 D2 D3hot D3cold
type 0 class 0x000880
@@ -516,7 +508,7 @@ system 00:0c: [mem 0xdfe72000-0xdfefffff
system 00:0c: [mem 0xdff00000-0xdfffffff] has been reserved
system 00:0c: [mem 0xffe00000-0xffffffff] has been reserved
system 00:0c: [mem 0xffa00000-0xffbfffff] has been reserved
-system 00:0c: [mem 0xfec00000-0xfec0ffff] could not be reserved
+system 00:0c: [mem 0xfec00000-0xfec0ffff] has been reserved
system 00:0c: [mem 0xfee00000-0xfee0ffff] has been reserved
system 00:0c: [mem 0xfed20000-0xfed8ffff] has been reserved
system 00:0c: [mem 0xfeda0000-0xfeda3fff] has been reserved
@@ -551,6 +543,10 @@ pci 0000:00:1c.4: bridge window [mem 0
pci 0000:00:1c.4: bridge window [mem 0xf0000000-0xf01fffff 64bit pref]
pci 0000:00:1e.0: PCI bridge to [bus 03-03]
pci 0000:00:1e.0: bridge window [mem 0xf1b00000-0xf1bfffff]
+ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
+PCI: setting IRQ 11 as level-triggered
+ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 7
+PCI: setting IRQ 7 as level-triggered
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
@@ -598,6 +594,11 @@ TCP reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
+ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
+ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 10
+PCI: setting IRQ 10 as level-triggered
+ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 9
+PCI: setting IRQ 9 as level-triggered
pci 0000:01:00.0: Boot video device
PCI: CLS 64 bytes, default 64
Unpacking initramfs...
@@ -606,7 +607,7 @@ Simple Boot Flag at 0x79 set to 0x1
apm: BIOS not found.
Intel AES-NI instructions are not detected.
audit: initializing netlink socket (disabled)
-type=2000 audit(1333888166.549:1): initialized
+type=2000 audit(1333888497.540:1): initialized
highmem bounce pool size: 64 pages
HugeTLB registered 4 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.2
@@ -619,10 +620,10 @@ Block layer SCSI generic (bsg) driver ve
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
-pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
-pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X
-pcieport 0000:00:1c.1: irq 42 for MSI/MSI-X
-pcieport 0000:00:1c.4: irq 43 for MSI/MSI-X
+pcieport 0000:00:01.0: irq 16 for MSI/MSI-X
+pcieport 0000:00:1c.0: irq 17 for MSI/MSI-X
+pcieport 0000:00:1c.1: irq 18 for MSI/MSI-X
+pcieport 0000:00:1c.4: irq 19 for MSI/MSI-X
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
@@ -648,7 +649,7 @@ Monitor-Mwait will be used to enter C-3
Marking TSC unstable due to TSC halts in idle
ACPI: acpi_idle registered with cpuidle
thermal LNXTHERM:00: registered as thermal_zone0
-ACPI: Thermal Zone [THM] (32 C)
+ACPI: Thermal Zone [THM] (55 C)
GHES: HEST is not enabled!
isapnp: Scanning for PnP cards...
(battery present)
@@ -658,17 +659,18 @@ Non-volatile memory driver v1.3
Linux agpgart interface v0.103
loop: module loaded
ahci 0000:00:1f.2: version 3.0
-ahci 0000:00:1f.2: irq 44 for MSI/MSI-X
+ahci 0000:00:1f.2: irq 20 for MSI/MSI-X
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x5 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ccc ems
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
-ata1: SATA max UDMA/133 abar m2048@0xf6ffb800 port 0xf6ffb900 irq 44
+ata1: SATA max UDMA/133 abar m2048@0xf6ffb800 port 0xf6ffb900 irq 20
ata2: DUMMY
-ata3: SATA max UDMA/133 abar m2048@0xf6ffb800 port 0xf6ffba00 irq 44
+ata3: SATA max UDMA/133 abar m2048@0xf6ffb800 port 0xf6ffba00 irq 20
ata_piix 0000:00:1f.1: version 2.13
+ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
ata_piix 0000:00:1f.1: setting latency timer to 64
scsi3 : ata_piix
scsi4 : ata_piix
@@ -682,7 +684,7 @@ ehci_hcd 0000:00:1a.7: EHCI Host Control
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.7: debug port 1
ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported
-ehci_hcd 0000:00:1a.7: irq 22, io mem 0xfed1c400
+ehci_hcd 0000:00:1a.7: irq 9, io mem 0xfed1c400
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
@@ -696,7 +698,7 @@ ehci_hcd 0000:00:1d.7: EHCI Host Control
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
-ehci_hcd 0000:00:1d.7: irq 20, io mem 0xfed1c000
+ehci_hcd 0000:00:1d.7: irq 11, io mem 0xfed1c000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
@@ -710,7 +712,7 @@ uhci_hcd: USB Universal Host Controller
uhci_hcd 0000:00:1a.0: setting latency timer to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
-uhci_hcd 0000:00:1a.0: irq 20, io base 0x00006f20
+uhci_hcd 0000:00:1a.0: irq 11, io base 0x00006f20
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
@@ -721,7 +723,7 @@ hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1a.1: setting latency timer to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
-uhci_hcd 0000:00:1a.1: irq 21, io base 0x00006f00
+uhci_hcd 0000:00:1a.1: irq 10, io base 0x00006f00
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
@@ -732,7 +734,7 @@ hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
-uhci_hcd 0000:00:1d.0: irq 20, io base 0x00006f80
+uhci_hcd 0000:00:1d.0: irq 11, io base 0x00006f80
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
@@ -743,7 +745,7 @@ hub 5-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
-uhci_hcd 0000:00:1d.1: irq 21, io base 0x00006f60
+uhci_hcd 0000:00:1d.1: irq 10, io base 0x00006f60
usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb6: Product: UHCI Host Controller
@@ -754,7 +756,7 @@ hub 6-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
-uhci_hcd 0000:00:1d.2: irq 22, io base 0x00006f40
+uhci_hcd 0000:00:1d.2: irq 9, io base 0x00006f40
usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb7: Product: UHCI Host Controller
@@ -790,14 +792,14 @@ Registering the dns_resolver key type
Using IPI No-Shortcut mode
PM: Hibernation image not present or could not be loaded.
registered taskstats version 1
- Magic number: 8:784:480
-rtc_cmos 00:04: setting system clock to 2012-04-08 12:29:28 UTC (1333888168)
+ Magic number: 8:887:581
+rtc_cmos 00:04: setting system clock to 2012-04-08 12:34:59 UTC (1333888499)
Initializing network drop monitor service
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
ata4.00: ATAPI: Optiarc DVD+/-RW AD-7640A, JD05, max UDMA/33
ata4.00: configured for UDMA/33
-ata3: SATA link down (SStatus 0 SControl 300)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
+ata3: SATA link down (SStatus 0 SControl 300)
ata1.00: ATA-7: ST9200420ASG, 3.ADD, max UDMA/133
ata1.00: 390721968 sectors, multi 8: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
@@ -813,19 +815,19 @@ sr0: scsi3-mmc drive: 24x/24x writer dvd
cdrom: Uniform CD-ROM driver Revision: 3.20
sr 3:0:0:0: Attached scsi CD-ROM sr0
sr 3:0:0:0: Attached scsi generic sg1 type 5
+usb 1-1: New USB device found, idVendor=05a9, idProduct=2640
+usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
+usb 1-1: Product: Laptop Integrated Webcam
+usb 1-1: Manufacturer: OmniVision Technologies, Inc. -2640-07.07.20.3
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 >
sd 0:0:0:0: [sda] Attached SCSI disk
Freeing unused kernel memory: 620k freed
Write protecting the kernel text: 5340k
Write protecting the kernel read-only data: 2096k
-usb 1-1: New USB device found, idVendor=05a9, idProduct=2640
-usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
-usb 1-1: Product: Laptop Integrated Webcam
-usb 1-1: Manufacturer: OmniVision Technologies, Inc. -2640-07.07.20.3
dracut: dracut-013-20.fc16
dracut: rd.luks=0: removing cryptoluks activation
dracut: rd.lvm=0: removing LVM activation
-udevd[111]: starting version 173
+udevd[112]: starting version 173
wmi: Mapper loaded
acpi device:31: registered as cooling_device2
input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:2e/LNXVIDEO:00/input/input4
@@ -859,36 +861,34 @@ usb 2-2: new high-speed USB device numbe
[drm] nouveau 0000:01:00.0: Parsing VBIOS init table 1 at offset 0xCB78
[drm] nouveau 0000:01:00.0: Parsing VBIOS init table 2 at offset 0xD5C8
[drm] nouveau 0000:01:00.0: Parsing VBIOS init table 3 at offset 0xD6BA
-usb 2-2: New USB device found, idVendor=0bb4, idProduct=0c99
-usb 2-2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
-usb 2-2: Product: Android Phone
[drm] nouveau 0000:01:00.0: Parsing VBIOS init table 4 at offset 0xD8ED
[drm] nouveau 0000:01:00.0: Parsing VBIOS init table at offset 0xD952
-usb 2-2: Manufacturer: HTC
-usb 2-2: SerialNumber: HT999L903452
[drm] nouveau 0000:01:00.0: 0xD952: Condition still not met after 20ms, skipping following opcodes
-Initializing USB Mass Storage driver...
-scsi5 : usb-storage 2-2:1.0
[drm] nouveau 0000:01:00.0: 3 available performance level(s)
[drm] nouveau 0000:01:00.0: 0: core 169MHz shader 338MHz memory 100MHz timing 0 voltage 1150mV fanspeed 100%
[drm] nouveau 0000:01:00.0: 1: core 275MHz shader 550MHz memory 301MHz timing 1 voltage 1150mV fanspeed 100%
[drm] nouveau 0000:01:00.0: 2: core 475MHz shader 950MHz memory 702MHz timing 2 voltage 1200mV fanspeed 100%
[drm] nouveau 0000:01:00.0: c: core 275MHz shader 550MHz memory 302MHz voltage 1150mV
-usbcore: registered new interface driver usb-storage
-USB Mass Storage support registered.
[TTM] Zone kernel: Available graphics memory: 429556 kiB.
[TTM] Zone highmem: Available graphics memory: 1811164 kiB.
[TTM] Initializing pool allocator.
[drm] nouveau 0000:01:00.0: Detected 256MiB VRAM
mtrr: type mismatch for e0000000,10000000 old: write-back new: write-combining
[drm] nouveau 0000:01:00.0: 512 MiB GART (aperture)
+usb 2-2: New USB device found, idVendor=0bb4, idProduct=0c99
+usb 2-2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
+usb 2-2: Product: Android Phone
+usb 2-2: Manufacturer: HTC
+usb 2-2: SerialNumber: HT999L903452
+Initializing USB Mass Storage driver...
+scsi5 : usb-storage 2-2:1.0
+usbcore: registered new interface driver usb-storage
+USB Mass Storage support registered.
[drm] nouveau 0000:01:00.0: DCB encoder 1 unknown
[drm] nouveau 0000:01:00.0: TV-1 has no encoders, removing
[drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[drm] No driver support for vblank timestamp query.
[drm] nouveau 0000:01:00.0: ACPI backlight interface available, not registering our own
-input: PS/2 Mouse as /devices/platform/i8042/serio1/input/input5
-input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio1/input/input6
usb 3-2: new full-speed USB device number 2 using uhci_hcd
usb 3-2: New USB device found, idVendor=0483, idProduct=2016
usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
@@ -899,13 +899,15 @@ usb 5-1: New USB device found, idVendor=
usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 5-1: Product: USB Full Speed
usb 5-1: Manufacturer: A4Tech
-input: A4Tech USB Full Speed as /devices/pci0000:00/0000:00:1d.0/usb5/5-1/5-1:1.0/input/input7
+input: A4Tech USB Full Speed as /devices/pci0000:00/0000:00:1d.0/usb5/5-1/5-1:1.0/input/input5
generic-usb 0003:09DA:8090.0001: input,hidraw0: USB HID v1.11 Mouse [A4Tech USB Full Speed] on usb-0000:00:1d.0-1/input0
-input: A4Tech USB Full Speed as /devices/pci0000:00/0000:00:1d.0/usb5/5-1/5-1:1.1/input/input8
+input: A4Tech USB Full Speed as /devices/pci0000:00/0000:00:1d.0/usb5/5-1/5-1:1.1/input/input6
generic-usb 0003:09DA:8090.0002: input,hiddev0,hidraw1: USB HID v1.11 Keyboard [A4Tech USB Full Speed] on usb-0000:00:1d.0-1/input1
scsi 5:0:0:0: Direct-Access HTC Android Phone 0100 PQ: 0 ANSI: 2
sd 5:0:0:0: Attached scsi generic sg2 type 0
sd 5:0:0:0: [sdb] Attached SCSI removable disk
+input: PS/2 Mouse as /devices/platform/i8042/serio1/input/input7
+input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio1/input/input8
usb 6-1: new full-speed USB device number 2 using uhci_hcd
usb 6-1: New USB device found, idVendor=054c, idProduct=03d5
usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
@@ -914,7 +916,7 @@ usb 6-1: Manufacturer: Sony Computer Ent
input: Sony Computer Entertainment Motion Controller as /devices/pci0000:00/0000:00:1d.1/usb6/6-1/6-1:1.0/input/input9
generic-usb 0003:054C:03D5.0003: input,hiddev0,hidraw2: USB HID v1.10 Gamepad [Sony Computer Entertainment Motion Controller] on usb-0000:00:1d.1-1/input0
composite sync not supported
-[drm] nouveau 0000:01:00.0: allocated 1440x900 fb: 0x320000, bo f28cf600
+[drm] nouveau 0000:01:00.0: allocated 1440x900 fb: 0x320000, bo f65ee800
fbcon: nouveaufb (fb0) is primary device
Console: switching to colour frame buffer device 180x56
fb0: nouveaufb frame buffer device
@@ -923,20 +925,20 @@ drm: registered panic notifier
dracut: Starting plymouth daemon
usb 7-2: new full-speed USB device number 2 using uhci_hcd
composite sync not supported
-dracut: rd.dm=0: removing DM RAID activation
usb 7-2: New USB device found, idVendor=0a5c, idProduct=4500
usb 7-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 7-2: Product: BCM2045B2
usb 7-2: Manufacturer: Broadcom
-dracut: rd.md=0: removing MD RAID activation
hub 7-2:1.0: USB hub found
hub 7-2:1.0: 3 ports detected
+dracut: rd.dm=0: removing DM RAID activation
+dracut: rd.md=0: removing MD RAID activation
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
+firewire_ohci: Added fw-ohci device 0000:03:09.0, OHCI v1.10, 4 IR + 4 IT contexts, quirks 0x11
(rev 22)
Registered led device: mmc0::
using DMA
-firewire_ohci: Added fw-ohci device 0000:03:09.0, OHCI v1.10, 4 IR + 4 IT contexts, quirks 0x11
usb 7-2.2: new full-speed USB device number 3 using uhci_hcd
usb 7-2.2: New USB device found, idVendor=0a5c, idProduct=4502
usb 7-2.2: New USB device strings: Mfr=1, Product=0, SerialNumber=0
@@ -944,21 +946,21 @@ usb 7-2.2: Manufacturer: Broadcom Corp
input: Broadcom Corp as /devices/pci0000:00/0000:00:1d.2/usb7/7-2/7-2.2/7-2.2:1.0/input/input10
generic-usb 0003:0A5C:4502.0004: input,hidraw3: USB HID v1.11 Keyboard [Broadcom Corp] on usb-0000:00:1d.2-2.2/input0
usb 7-2.3: new full-speed USB device number 4 using uhci_hcd
-firewire_core: created device fw0: GUID 334fc0001cece070, S400
usb 7-2.3: New USB device found, idVendor=0a5c, idProduct=4503
usb 7-2.3: New USB device strings: Mfr=1, Product=0, SerialNumber=0
usb 7-2.3: Manufacturer: Broadcom Corp
input: Broadcom Corp as /devices/pci0000:00/0000:00:1d.2/usb7/7-2/7-2.3/7-2.3:1.0/input/input11
generic-usb 0003:0A5C:4503.0005: input,hidraw4: USB HID v1.11 Mouse [Broadcom Corp] on usb-0000:00:1d.2-2.3/input0
+firewire_core: created device fw0: GUID 334fc0001cece070, S400
EXT4-fs (sda7): mounted filesystem with ordered data mode. Opts: (null)
dracut: Checking ext4: /dev/disk/by-uuid/7417d839-a647-466e-b57d-fc65d20a6342
dracut: issuing e2fsck -a /dev/disk/by-uuid/7417d839-a647-466e-b57d-fc65d20a6342
-dracut: _Fedora-16-i686-: clean, 238747/901120 files, 1776110/3584000 blocks
+dracut: _Fedora-16-i686-: clean, 238750/901120 files, 1775993/3584000 blocks
dracut: Remounting /dev/disk/by-uuid/7417d839-a647-466e-b57d-fc65d20a6342 with -o ro
EXT4-fs (sda7): mounted filesystem with ordered data mode. Opts: (null)
dracut: Mounted root filesystem /dev/sda7
dracut: Switching root
-type=1404 audit(1333888173.684:2): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
+type=1404 audit(1333888504.678:2): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
SELinux: 2048 avtab hash slots, 97362 rules.
SELinux: 2048 avtab hash slots, 97362 rules.
SELinux: 9 users, 13 roles, 3912 types, 215 bools, 1 sens, 1024 cats
@@ -984,13 +986,13 @@ SELinux: initialized (dev sysfs, type sy
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev sda7, type ext4), uses xattr
-type=1403 audit(1333888173.953:3): policy loaded auid=4294967295 ses=4294967295
-systemd[1]: Successfully loaded SELinux policy in 347ms 981us.
-systemd[1]: Successfully loaded SELinux database in 54ms 927us, size on heap is 365K.
+type=1403 audit(1333888504.936:3): policy loaded auid=4294967295 ses=4294967295
+systemd[1]: Successfully loaded SELinux policy in 331ms 344us.
+systemd[1]: Successfully loaded SELinux database in 63ms 586us, size on heap is 365K.
systemd[1]: RTC configured in localtime, applying delta of 60 minutes to system time.
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
-systemd[1]: Relabelled /dev and /run in 42ms 476us.
+systemd[1]: Relabelled /dev and /run in 42ms 435us.
SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
SELinux: initialized (dev cgroup, type cgroup), uses genfs_contexts
@@ -1002,11 +1004,11 @@ SELinux: initialized (dev cgroup, type c
systemd[1]: systemd 37 running in system mode. (+PAM +LIBWRAP +AUDIT +SELINUX +SYSVINIT +LIBCRYPTSETUP; fedora)
systemd[1]: Set hostname to <xps>.
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
-udevd[521]: starting version 173
-udevd[521]: specified group 'plugdev' unknown
-SELinux: initialized (dev configfs, type configfs), uses genfs_contexts
+udevd[524]: starting version 173
+udevd[524]: specified group 'plugdev' unknown
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses transition SIDs
+SELinux: initialized (dev configfs, type configfs), uses genfs_contexts
SELinux: initialized (dev securityfs, type securityfs), uses genfs_contexts
EXT4-fs (sda7): re-mounted. Opts: (null)
RPC: Registered named UNIX socket transport module.
@@ -1017,44 +1019,39 @@ SELinux: initialized (dev rpc_pipefs, ty
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
sky2: driver version 1.30
sky2 0000:09:00.0: Yukon-2 FE+ chip revision 0
-sky2 0000:09:00.0: irq 45 for MSI/MSI-X
+sky2 0000:09:00.0: irq 21 for MSI/MSI-X
sky2 0000:09:00.0: eth0: addr 00:21:9b:cd:55:50
cfg80211: Calling CRDA to update world regulatory domain
iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, in-tree:ds
iwl3945: Copyright(c) 2003-2011 Intel Corporation
-iwl3945 0000:0b:00.0: enabling device (0000 -> 0002)
-iwl3945 0000:0b:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0xFFFFFFFF
+r592: driver successfully loaded
iTCO_vendor_support: vendor-support=0
-iwl3945 0000:0b:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0xFFFFFFFF
-iwl3945 0000:0b:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0xFFFFFFFF
-iwl3945 0000:0b:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0xFFFFFFFF
-iwl3945 0000:0b:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0xFFFFFFFF
-iwl3945 0000:0b:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0xFFFFFFFF
-iwl3945 0000:0b:00.0: bad EEPROM signature,EEPROM_GP=0x00000007
-iwl3945 0000:0b:00.0: EEPROM not found, EEPROM_GP=0xffffffff
-iwl3945 0000:0b:00.0: Unable to init EEPROM
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
iTCO_wdt: Found a ICH8M TCO device (Version=2, TCOBASE=0x1060)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
-iwl3945: probe of 0000:0b:00.0 failed with error -2
+iwl3945 0000:0b:00.0: Tunable channels: 13 802.11bg, 23 802.11a channels
+iwl3945 0000:0b:00.0: Detected Intel Wireless WiFi Link 3945ABG
+iwl3945 0000:0b:00.0: irq 22 for MSI/MSI-X
+Registered led device: phy0-led
+mtp-probe[676]: checking bus 3, device 2: "/sys/devices/pci0000:00/0000:00:1a.0/usb3/3-2"
+mtp-probe[694]: checking bus 2, device 3: "/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-2"
+mtp-probe[692]: checking bus 1, device 2: "/sys/devices/pci0000:00/0000:00:1a.7/usb1/1-1"
microcode: CPU0 sig=0x10676, pf=0x80, revision=0x60c
-r592: driver successfully loaded
-mtp-probe[674]: checking bus 6, device 2: "/sys/devices/pci0000:00/0000:00:1d.1/usb6/6-1"
+mtp-probe[695]: checking bus 5, device 2: "/sys/devices/pci0000:00/0000:00:1d.0/usb5/5-1"
+mtp-probe[716]: checking bus 6, device 2: "/sys/devices/pci0000:00/0000:00:1d.1/usb6/6-1"
+mtp-probe[694]: bus: 2, device: 3 was not an MTP device
+mtp-probe[692]: bus: 1, device: 2 was not an MTP device
+mtp-probe[716]: bus: 6, device: 2 was not an MTP device
+mtp-probe[676]: bus: 3, device: 2 was not an MTP device
mtp-probe[724]: checking bus 7, device 3: "/sys/devices/pci0000:00/0000:00:1d.2/usb7/7-2/7-2.2"
-mtp-probe[670]: checking bus 5, device 2: "/sys/devices/pci0000:00/0000:00:1d.0/usb5/5-1"
-mtp-probe[691]: checking bus 2, device 3: "/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-2"
-mtp-probe[684]: checking bus 1, device 2: "/sys/devices/pci0000:00/0000:00:1a.7/usb1/1-1"
-mtp-probe[650]: checking bus 3, device 2: "/sys/devices/pci0000:00/0000:00:1a.0/usb3/3-2"
-mtp-probe[730]: checking bus 7, device 4: "/sys/devices/pci0000:00/0000:00:1d.2/usb7/7-2/7-2.3"
-mtp-probe[691]: bus: 2, device: 3 was not an MTP device
+mtp-probe[729]: checking bus 7, device 4: "/sys/devices/pci0000:00/0000:00:1d.2/usb7/7-2/7-2.3"
+mtp-probe[729]: bus: 7, device: 4 was not an MTP device
+mtp-probe[695]: bus: 5, device: 2 was not an MTP device
mtp-probe[724]: bus: 7, device: 3 was not an MTP device
-mtp-probe[670]: bus: 5, device: 2 was not an MTP device
-mtp-probe[684]: bus: 1, device: 2 was not an MTP device
-mtp-probe[674]: bus: 6, device: 2 was not an MTP device
-mtp-probe[730]: bus: 7, device: 4 was not an MTP device
-mtp-probe[650]: bus: 3, device: 2 was not an MTP device
-dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
r852: driver loaded successfully
+dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
+Linux media interface: v0.10
+ieee80211 phy0: Selected rate control algorithm 'iwl-3945-rs'
cfg80211: World regulatory domain updated:
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
@@ -1062,19 +1059,19 @@ cfg80211: (2457000 KHz - 2482000 KHz @
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
+input: Dell WMI hotkeys as /devices/virtual/input/input12
microcode: CPU0 updated to revision 0x60f, date = 2010-09-29
microcode: CPU1 sig=0x10676, pf=0x80, revision=0x60c
microcode: CPU1 updated to revision 0x60f, date = 2010-09-29
microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
-Linux media interface: v0.10
Linux video capture interface: v2.00
-input: Dell WMI hotkeys as /devices/virtual/input/input12
-snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X
+udevd[583]: renamed network interface eth0 to p2p1
uvcvideo: Found UVC 1.00 device Laptop Integrated Webcam (05a9:2640)
uvcvideo: UVC non compliance - GET_DEF(PROBE) not supported. Enabling workaround.
input: Laptop Integrated Webcam as /devices/pci0000:00/0000:00:1a.7/usb1/1-1/1-1:1.0/input/input13
usbcore: registered new interface driver uvcvideo
USB Video Class driver (1.1.1)
+snd_hda_intel 0000:00:1b.0: irq 23 for MSI/MSI-X
ALSA sound/pci/hda/hda_codec.c:4927 autoconfig: line_outs=1 (0xd/0x0/0x0/0x0/0x0) type:speaker
ALSA sound/pci/hda/hda_codec.c:4931 speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
ALSA sound/pci/hda/hda_codec.c:4935 hp_outs=2 (0xa/0xf/0x0/0x0/0x0)
@@ -1085,59 +1082,65 @@ ALSA sound/pci/hda/hda_codec.c:4944 Int
ALSA sound/pci/hda/hda_codec.c:4944 Mic=0xe
ALSA sound/pci/hda/hda_codec.c:4946
ALSA sound/pci/hda/patch_sigmatel.c:3090 stac92xx: dac_nids=2 (0x2/0x5/0x0/0x0/0x0)
-udevd[609]: renamed network interface eth0 to p2p1
+cfg80211: Calling CRDA for country: GB
+cfg80211: Regulatory domain changed to country: GB
+cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
+cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
+cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
+cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
+cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
+Adding 2047996k swap on /dev/sda8. Priority:0 extents:1 across:2047996k
fuse init (API version 7.18)
SELinux: initialized (dev fusectl, type fusectl), uses genfs_contexts
-mount[900]: mount: fusectl already mounted or /sys/fs/fuse/connections busy
-mount[900]: mount: according to mtab, fusectl is already mounted on /sys/fs/fuse/connections
+mount[931]: mount: fusectl already mounted or /sys/fs/fuse/connections busy
+mount[931]: mount: according to mtab, fusectl is already mounted on /sys/fs/fuse/connections
systemd[1]: sys-fs-fuse-connections.mount mount process exited, code=exited status=32
-Adding 2047996k swap on /dev/sda8. Priority:0 extents:1 across:2047996k
-systemd-fsck[893]: /dev/sda5: clean, 281/76304 files, 117477/304216 blocks
SELinux: initialized (dev sda3, type fuseblk), uses genfs_contexts
-ntfs-3g[923]: Version 2011.4.12 integrated FUSE 27
-ntfs-3g[923]: Mounted /dev/sda3 (Read-Write, label "", NTFS 3.1)
-ntfs-3g[923]: Cmdline options: rw
-ntfs-3g[923]: Mount options: rw,allow_other,nonempty,atime,fsname=/dev/sda3,blkdev,blksize=4096
-ntfs-3g[923]: Ownership and permissions disabled, configuration type 1
-fedora-storage-init[912]: Setting up Logical Volume Management: No volume groups found
-fedora-storage-init[912]: [ OK ]
-EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)
-SELinux: initialized (dev sda5, type ext4), uses xattr
-fedora-storage-init[925]: Setting up Logical Volume Management: No volume groups found
-fedora-storage-init[925]: [ OK ]
-systemd-fsck[903]: /home: clean, 1056585/5799936 files, 19080578/23175424 blocks
-lvm[935]: No volume groups found
+ntfs-3g[950]: Version 2011.4.12 integrated FUSE 27
+ntfs-3g[950]: Mounted /dev/sda3 (Read-Write, label "", NTFS 3.1)
+ntfs-3g[950]: Cmdline options: rw
+ntfs-3g[950]: Mount options: rw,allow_other,nonempty,atime,fsname=/dev/sda3,blkdev,blksize=4096
+ntfs-3g[950]: Ownership and permissions disabled, configuration type 1
+systemd-fsck[925]: /home: clean, 1056585/5799936 files, 19080275/23175424 blocks
EXT4-fs (sda6): mounting ext3 file system using the ext4 subsystem
+fedora-storage-init[944]: Setting up Logical Volume Management: No volume groups found
+fedora-storage-init[944]: [ OK ]
EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null)
SELinux: initialized (dev sda6, type ext3), uses xattr
+systemd-fsck[935]: /dev/sda5: clean, 281/76304 files, 117477/304216 blocks
EXT4-fs (sda9): warning: maximal mount count reached, running e2fsck is recommended
EXT4-fs (sda9): mounted filesystem with ordered data mode. Opts: (null)
SELinux: initialized (dev sda9, type ext4), uses xattr
-systemd-tmpfiles[951]: Successfully loaded SELinux database in 13ms 399us, size on heap is 366K.
+fedora-storage-init[957]: Setting up Logical Volume Management: No volume groups found
+fedora-storage-init[957]: [ OK ]
+EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)
+SELinux: initialized (dev sda5, type ext4), uses xattr
+lvm[975]: No volume groups found
+systemd-tmpfiles[982]: Successfully loaded SELinux database in 14ms 107us, size on heap is 366K.
+mcelog[1015]: mcelog read: No such device
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
-auditd[965]: Started dispatcher: /sbin/audispd pid: 990
-iptables.init[959]: iptables: Applying firewall rules: [ OK ]
-audispd[990]: priority_boost_parser called with: 4
-audispd[990]: max_restarts_parser called with: 10
-audispd[990]: audispd initialized with q_depth=120 and 1 active plugins
ip6_tables: (C) 2000-2006 Netfilter Core Team
-ip6tables.init[960]: ip6tables: Applying firewall rules: [ OK ]
-NetworkManager[1003]: <info> NetworkManager (version 0.9.2-1.fc16) is starting...
-NetworkManager[1003]: <info> Read config file /etc/NetworkManager/NetworkManager.conf
-NetworkManager[1003]: NetworkManager[1003]: <info> NetworkManager (version 0.9.2-1.fc16) is starting...
-NetworkManager[1003]: NetworkManager[1003]: <info> Read config file /etc/NetworkManager/NetworkManager.conf
-mcelog[996]: mcelog read: No such device
-auditctl[973]: No rules
-auditctl[973]: AUDIT_STATUS: enabled=0 flag=1 pid=965 rate_limit=0 backlog_limit=320 lost=0 backlog=0
-abrtd[1011]: Init complete, entering main loop
-acpid[1026]: starting up with netlink and the input layer
-acpid[1026]: skipping incomplete file /etc/acpi/events/videoconf
-acpid[1026]: 1 rule loaded
-acpid[1026]: waiting for events: event logging is off
-avahi-daemon[1025]: Found user 'avahi' (UID 70) and group 'avahi' (GID 70).
-avahi-daemon[1025]: Successfully dropped root privileges.
-avahi-daemon[1025]: avahi-daemon 0.6.30 starting up.
-auditd[965]: Init complete, auditd 2.1.3 listening for events (startup state enable)
+iptables.init[991]: iptables: Applying firewall rules: [ OK ]
+ip6tables.init[993]: ip6tables: Applying firewall rules: [ OK ]
+NetworkManager[1029]: <info> NetworkManager (version 0.9.2-1.fc16) is starting...
+NetworkManager[1029]: <info> Read config file /etc/NetworkManager/NetworkManager.conf
+NetworkManager[1029]: NetworkManager[1029]: <info> NetworkManager (version 0.9.2-1.fc16) is starting...
+NetworkManager[1029]: NetworkManager[1029]: <info> Read config file /etc/NetworkManager/NetworkManager.conf
+auditd[995]: Started dispatcher: /sbin/audispd pid: 1042
+audispd[1042]: priority_boost_parser called with: 4
+audispd[1042]: max_restarts_parser called with: 10
+audispd[1042]: audispd initialized with q_depth=120 and 1 active plugins
+auditctl[1001]: No rules
+auditctl[1001]: AUDIT_STATUS: enabled=0 flag=1 pid=0 rate_limit=0 backlog_limit=320 lost=0 backlog=0
+abrtd[1038]: Init complete, entering main loop
+avahi-daemon[1051]: Found user 'avahi' (UID 70) and group 'avahi' (GID 70).
+avahi-daemon[1051]: Successfully dropped root privileges.
+avahi-daemon[1051]: avahi-daemon 0.6.30 starting up.
+acpid[1064]: starting up with netlink and the input layer
+acpid[1064]: skipping incomplete file /etc/acpi/events/videoconf
+acpid[1064]: 1 rule loaded
+acpid[1064]: waiting for events: event logging is off
+auditd[995]: Init complete, auditd 2.1.3 listening for events (startup state enable)
Loading iSCSI transport class v2.0-870.
iscsi: registered transport (tcp)
iscsi: registered transport (iser)
@@ -1153,6 +1156,8 @@ iscsi: registered transport (bnx2i)
iscsi: registered transport (be2iscsi)
sky2 0000:09:00.0: p2p1: enabling interface
ADDRCONF(NETDEV_UP): p2p1: link is not ready
+iwl3945 0000:0b:00.0: loaded firmware version 15.32.2.9
+ADDRCONF(NETDEV_UP): wlan0: link is not ready
8021q: 802.1Q VLAN Support v1.8
netlink: 12 bytes leftover after parsing attributes.
netlink: 12 bytes leftover after parsing attributes.
@@ -1160,5 +1165,15 @@ netlink: 12 bytes leftover after parsing
composite sync not supported
composite sync not supported
composite sync not supported
+wlan0: authenticate with 00:8b:5d:90:fa:8a (try 1)
+wlan0: authenticated
+wlan0: associate with 00:8b:5d:90:fa:8a (try 1)
+wlan0: RX AssocResp from 00:8b:5d:90:fa:8a (capab=0x431 status=0 aid=1)
+wlan0: associated
+wlan0: moving STA 00:8b:5d:90:fa:8a to state 1
+wlan0: moving STA 00:8b:5d:90:fa:8a to state 2
+ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
+wlan0: moving STA 00:8b:5d:90:fa:8a to state 3
composite sync not supported
hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj.
+wlan0: no IPv6 routers present
Sorry this got dropped on the floor for so long. I don't see anything
wrong with the PCI memory routing information in either the failing or
the working logs.
Kamil, you mentioned: "Driver can't initialize card as all
ioread32/iowrite32 seems to not do their job. All reads finalize with
0xffffffff."
Normally this means we got no response, either because the transaction
didn't reach the device, or the device didn't respond. Here's the
routing information I see, which looks fine:
ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
pci_root PNP0A03:00: host bridge window [mem 0xe0000000-0xf7ffffff]
pci 0000:00:1c.1: PCI bridge to [bus 0b-0b]
pci 0000:00:1c.1: bridge window [mem 0xf1e00000-0xf1efffff]
pci 0000:0b:00.0: [8086:4222] type 0 class 0x000280
pci 0000:0b:00.0: reg 10: [mem 0xf1eff000-0xf1efffff]
And we enabled memory space decoding for the device:
iwl3945 0000:0b:00.0: enabling device (0000 -> 0002)
so it *should* respond. It's interesting that we didn't have to
enable the device in the working ("noapic") case -- there's no
"enabling device" line in that dmesg log, which means memory decoding
was already enabled when we found it.
You also said "If I access the memory directly, not by mapping, I can
write and read pci memory but driver load fails anyway." What exactly
does that mean? I assume you mean that even in the failing case, you
can somehow access that region ([mem 0xf1eff000-0xf1efffff]). What
mechanism are you using? ioremap() in the driver? User-space mmap of
a /sys file?
You said "This issue is reproducible in 100% on my system when I turn
on the machine. It doesn't occur after some work on it." I wonder if
there's some timing issue with that device coming out of reset or
something. Does the same problem happen if the driver is statically
linked in vs. loaded as a module after boot? What if you add a long
delay in the driver probe routine?
On Mon, May 28, 2012 at 12:21:34PM -0600, Bjorn Helgaas wrote:
> linked in vs. loaded as a module after boot? What if you add a long
> delay in the driver probe routine?
I'm attaching patch which add 200 ms delay after pci_enable_device() in
->probe routine.
Stanislaw
On Tue, May 29, 2012 at 3:21 AM, Stanislaw Gruszka <[email protected]> wrote:
> On Mon, May 28, 2012 at 12:21:34PM -0600, Bjorn Helgaas wrote:
>> linked in vs. loaded as a module after boot? ?What if you add a long
>> delay in the driver probe routine?
>
> I'm attaching patch which add 200 ms delay after pci_enable_device() in
> ->probe routine.
>
> Stanislaw
Kamil, any news on this issue?