I get a board with 8168e-vl(10ec:8168 with RTL_GIGA_MAC_VER_34),
everything looks well first, I can use ifconfig to set ip, netmask,
etc. And the rx/tx statistics show by ifconfig looks good when I
ping another host or ping it from another host. But it don't work,
I can't get ICMP REPLAY from both sides, although the RX/TX statistics
seem good.
After add some debug code, I found this NIC only accept ethernet
broadcast package, it can't filter out the package send to its
MAC address, but it works good for sending.So ifconfig show the
RX/TX status means it can receive ARP package.(It don't its MAC
address, so below)
I have try the driver provided by realtek's website, it have the
same problem at the first time. BUT IT WORK AFTER I REBOOT with
CRTL-ALT-DEL, the reason is that realtek's driver call rtl8168_rar_set
in the .shutdown function register with pci_register_driver. Yes,
the really reason to make it work is rtl8689_rar_set, this function
set extended GigaMAC registers, so after reboot without lost the power,
NIC keep the status before reboot.
I haven't see any code to set GigaMAC registers in kernel when boot,
so I guess BIOS or NIC's circuit make it, but of course one miss
the extended GigaMAC registers in this problem. The probe code can
get MAC address right, so MAC{0,4} must had been setted, but some
guys forget the extended GigaMAC registers.
This patch fix it.
[ I don't known whether others' realtek's NIC with extended GigaMAC
reigisters have the same problem, I meet it in 8168e-vl with
RTL_GIGA_MAC_VER_34, so I make this patch just for it.]
Signed-off-by: Wang YanQing <[email protected]>
---
drivers/net/ethernet/realtek/r8169.c | 24 ++++++++++++++++++++++++
1 file changed, 24 insertions(+)
diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net/ethernet/realtek/r8169.c
index 927aa33..e49c08d 100644
--- a/drivers/net/ethernet/realtek/r8169.c
+++ b/drivers/net/ethernet/realtek/r8169.c
@@ -3095,7 +3095,30 @@ static void rtl8168e_1_hw_phy_config(struct rtl8169_private *tp)
rtl_writephy(tp, 0x0e, 0x0000);
rtl_writephy(tp, 0x0d, 0x0000);
}
+static void rtl8168e_2_workaround(struct rtl8169_private *tp, u8 *addr)
+{
+ void __iomem *ioaddr = tp->mmio_addr;
+ u32 high;
+ u32 low;
+
+ low = addr[0] | (addr[1] << 8) | (addr[2] << 16) | (addr[3] << 24);
+ high = addr[4] | (addr[5] << 8);
+
+
+ RTL_W8(Cfg9346, Cfg9346_Unlock);
+ if (tp->mac_version == RTL_GIGA_MAC_VER_34) {
+ const struct exgmac_reg e[] = {
+ { .addr = 0xe0, ERIAR_MASK_1111, .val = low },
+ { .addr = 0xe4, ERIAR_MASK_1111, .val = high },
+ { .addr = 0xf0, ERIAR_MASK_1111, .val = low << 16 },
+ { .addr = 0xf4, ERIAR_MASK_1111, .val = high << 16 |
+ low >> 16 },
+ };
+ rtl_write_exgmac_batch(tp, e, ARRAY_SIZE(e));
+ }
+ RTL_W8(Cfg9346, Cfg9346_Lock);
+}
static void rtl8168e_2_hw_phy_config(struct rtl8169_private *tp)
{
static const struct phy_reg phy_reg_init[] = {
@@ -3178,6 +3201,7 @@ static void rtl8168e_2_hw_phy_config(struct rtl8169_private *tp)
rtl_w1w0_phy(tp, 0x19, 0x0000, 0x0001);
rtl_w1w0_phy(tp, 0x10, 0x0000, 0x0400);
rtl_writephy(tp, 0x1f, 0x0000);
+ rtl8168e_2_workaround(tp, tp->dev->dev_addr);
}
static void rtl8168f_hw_phy_config(struct rtl8169_private *tp)
--
1.7.11.1.116.g8228a23
Wang YanQing <[email protected]> :
[...]
> After add some debug code, I found this NIC only accept ethernet
> broadcast package, it can't filter out the package send to its
> MAC address, but it works good for sending.So ifconfig show the
> RX/TX status means it can receive ARP package.(It don't its MAC
> address, so below)
Which kernel version is it ?
[...]
> I haven't see any code to set GigaMAC registers in kernel when boot,
> so I guess BIOS or NIC's circuit make it, but of course one miss
I'd appreciate to figure it out (and understand why I did not notice
it when testing).
> the extended GigaMAC registers in this problem. The probe code can
> get MAC address right, so MAC{0,4} must had been setted, but some
> guys forget the extended GigaMAC registers.
>
> This patch fix it.
It is a good analysis job.
I'd rather see the GigaMAC registers written through a call to
rtl_rar_set when the mac address is read in rtl_init_one instead
of duplicating most of rtl_rar_set in a quite different place.
Hayes, can you specify if it would work or if it may mess the registers
init sequence ordering ?
Thanks.
--
Ueimor
On Fri, Nov 30, 2012 at 07:35:00AM +0100, Francois Romieu wrote:
> Which kernel version is it ?
I have done the test and debug with mainline
e23739b4ade80a3a7f87198f008f6c44a7cbc9fd, v3.7-rc7-51-ge23739b
> I'd rather see the GigaMAC registers written through a call to
> rtl_rar_set when the mac address is read in rtl_init_one instead
> of duplicating most of rtl_rar_set in a quite different place.
I have the same feeling with you, I will resend the patch follow
your opinion if everything pass test and work.
Thanks
On Fri, Nov 30, 2012 at 05:04:29PM +0800, Wang YanQing wrote:
> On Fri, Nov 30, 2012 at 07:35:00AM +0100, Francois Romieu wrote:
> > Which kernel version is it ?
> I have done the test and debug with mainline
> e23739b4ade80a3a7f87198f008f6c44a7cbc9fd, v3.7-rc7-51-ge23739b
More exactly, I find the problem in 3.0 stable tree, and fix it
for 3.0 stable tree first, then re test and debug for mainline,
e23739b4ade80a3a7f87198f008f6c44a7cbc9fd, v3.7-rc7-51-ge23739b.
I found the mainline's r8169 works the same as realtek's driver,
the first time don't work, but it works after reboot, the reason
is the pci driver's shutdown don't call rtl_rar_set in 3.0 stable
tree but the mainline does.
Thanks.
On Fri, Nov 30, 2012 at 06:00:02PM +0800, Wang YanQing wrote:
> I found the mainline's r8169 works the same as realtek's driver,
> the first time don't work, but it works after reboot, the reason
> is the pci driver's shutdown don't call rtl_rar_set in 3.0 stable
> tree but the mainline does.
Sorry, I make a mistake here, the boths pci driver's shutdown call
rtl_rar_set, but 3.0 stable tree don't include commit
c28aa38567101bad4e020f4392df41d0bf6c165c(r8169 : MAC address change fix for the 8168e-vl)
Thanks