gpio: Renesas R-Car GPIO driver update
[PATCH 01/03] gpio: Renesas R-Car GPIO driver V2
[PATCH 02/03] gpio: rcar: Use IRQCHIP_SET_TYPE_MASKED
[PATCH 03/03] gpio: rcar: Make use of devm functions
This series updates the R-Car GPIO driver with various
changes kindly suggested by Laurent Pinchart.
Patch [01/03] is a drop in replacement for V1 of the R-Car
GPIO driver. The flag in patch [02/03] is kept out of [01/03]
to avoid changing the behaviour of the driver between V1 and V2.
Also, devm support in [03/03] is kept out of [01/03] to make
sure back porting goes as smooth as possible.
Signed-off-by: Magnus Damm <[email protected]>
---
drivers/gpio/Kconfig | 6
drivers/gpio/Makefile | 1
drivers/gpio/gpio-rcar.c | 417 +++++++++++++++++++++++++++++--
include/linux/platform_data/gpio-rcar.h | 25 +
4 files changed, 427 insertions(+), 22 deletions(-)
From: Magnus Damm <[email protected]>
This patch is V2 of a GPIO driver for the R-Car series of
SoCs from Renesas. This driver is designed to be reusable
between multiple SoCs that share the same basic building block,
but so far it has only been used on R-Car H1 (r8a7779).
Each driver instance handles 32 GPIOs with individually
maskable IRQs. The driver operates on a single I/O memory
range and the 32 GPIOs are hooked up a single interrupt.
In the case of R-Car H1 either external IRQ pins or GPIOs
with interrupts can be used for on-board interupts. For
external IRQs 4 pins are supported, and in the case of GPIO
there are 202 GPIOS as 202 interrupts hooked up via 6 driver
instances and to the GIC and the Cortex-A9 Quad.
At this point this driver is interfacing as a regular
platform device driver. In the future DT support will be
submitted as an incremental feature patch.
Signed-off-by: Magnus Damm <[email protected]>
---
Changes since V1:
- Update based on most suggestions from review by Laurent, thanks!
Please note that in V2 the driver is reworked to reduce the number of
lines and includes minor changes related to headers, printouts and
data types. In V2 the register access order is kept the same as in V1,
and to make that happen IRQCHIP_SET_TYPE_MASKED is omitted. The interface
to the Linux kernel is unchanged except the use of dev_dbg() instead of
pr_debug(). So from a hardware point of view V2 is a drop in replacement
for V1 and there should be no additional dependencies since devm is
kept as a separate patch as well. All this to make back porting easier.
drivers/gpio/Kconfig | 6
drivers/gpio/Makefile | 1
drivers/gpio/gpio-rcar.c | 383 +++++++++++++++++++++++++++++++
include/linux/platform_data/gpio-rcar.h | 25 ++
4 files changed, 415 insertions(+)
--- 0001/drivers/gpio/Kconfig
+++ work/drivers/gpio/Kconfig 2013-03-13 19:39:44.000000000 +0900
@@ -201,6 +201,12 @@ config GPIO_PXA
help
Say yes here to support the PXA GPIO device
+config GPIO_RCAR
+ tristate "Renesas R-Car GPIO"
+ depends on ARM
+ help
+ Say yes here to support GPIO on Renesas R-Car SoCs.
+
config GPIO_SPEAR_SPICS
bool "ST SPEAr13xx SPI Chip Select as GPIO support"
depends on PLAT_SPEAR
--- 0001/drivers/gpio/Makefile
+++ work/drivers/gpio/Makefile 2013-03-13 19:39:44.000000000 +0900
@@ -56,6 +56,7 @@ obj-$(CONFIG_GPIO_PL061) += gpio-pl061.o
obj-$(CONFIG_GPIO_PXA) += gpio-pxa.o
obj-$(CONFIG_GPIO_RC5T583) += gpio-rc5t583.o
obj-$(CONFIG_GPIO_RDC321X) += gpio-rdc321x.o
+obj-$(CONFIG_GPIO_RCAR) += gpio-rcar.o
obj-$(CONFIG_PLAT_SAMSUNG) += gpio-samsung.o
obj-$(CONFIG_ARCH_SA1100) += gpio-sa1100.o
obj-$(CONFIG_GPIO_SCH) += gpio-sch.o
--- /dev/null
+++ work/drivers/gpio/gpio-rcar.c 2013-03-13 19:41:35.000000000 +0900
@@ -0,0 +1,383 @@
+/*
+ * Renesas R-Car GPIO Support
+ *
+ * Copyright (C) 2013 Magnus Damm
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/err.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/ioport.h>
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/module.h>
+#include <linux/platform_data/gpio-rcar.h>
+#include <linux/platform_device.h>
+#include <linux/spinlock.h>
+#include <linux/slab.h>
+
+struct gpio_rcar_priv {
+ void __iomem *base;
+ spinlock_t lock;
+ struct gpio_rcar_config config;
+ struct platform_device *pdev;
+ struct gpio_chip gpio_chip;
+ struct irq_chip irq_chip;
+ struct irq_domain *irq_domain;
+};
+
+#define IOINTSEL 0x00
+#define INOUTSEL 0x04
+#define OUTDT 0x08
+#define INDT 0x0c
+#define INTDT 0x10
+#define INTCLR 0x14
+#define INTMSK 0x18
+#define MSKCLR 0x1c
+#define POSNEG 0x20
+#define EDGLEVEL 0x24
+#define FILONOFF 0x28
+
+static inline u32 gpio_rcar_read(struct gpio_rcar_priv *p, int offs)
+{
+ return ioread32(p->base + offs);
+}
+
+static inline void gpio_rcar_write(struct gpio_rcar_priv *p, int offs,
+ u32 value)
+{
+ iowrite32(value, p->base + offs);
+}
+
+static void gpio_rcar_modify_bit(struct gpio_rcar_priv *p, int offs,
+ int bit, bool value)
+{
+ u32 tmp = gpio_rcar_read(p, offs);
+
+ if (value)
+ tmp |= BIT(bit);
+ else
+ tmp &= ~BIT(bit);
+
+ gpio_rcar_write(p, offs, tmp);
+}
+
+static void gpio_rcar_irq_disable(struct irq_data *d)
+{
+ struct gpio_rcar_priv *p = irq_data_get_irq_chip_data(d);
+
+ gpio_rcar_write(p, INTMSK, ~BIT(irqd_to_hwirq(d)));
+}
+
+static void gpio_rcar_irq_enable(struct irq_data *d)
+{
+ struct gpio_rcar_priv *p = irq_data_get_irq_chip_data(d);
+
+ gpio_rcar_write(p, MSKCLR, BIT(irqd_to_hwirq(d)));
+}
+
+static void gpio_rcar_config_interrupt_input_mode(struct gpio_rcar_priv *p,
+ unsigned int hwirq,
+ bool active_high_rising_edge,
+ bool level_trigger)
+{
+ unsigned long flags;
+
+ /* follow steps in the GPIO documentation for
+ * "Setting Edge-Sensitive Interrupt Input Mode" and
+ * "Setting Level-Sensitive Interrupt Input Mode"
+ */
+
+ spin_lock_irqsave(&p->lock, flags);
+
+ /* Configure postive or negative logic in POSNEG */
+ gpio_rcar_modify_bit(p, POSNEG, hwirq, !active_high_rising_edge);
+
+ /* Configure edge or level trigger in EDGLEVEL */
+ gpio_rcar_modify_bit(p, EDGLEVEL, hwirq, !level_trigger);
+
+ /* Select "Interrupt Input Mode" in IOINTSEL */
+ gpio_rcar_modify_bit(p, IOINTSEL, hwirq, true);
+
+ /* Write INTCLR in case of edge trigger */
+ if (!level_trigger)
+ gpio_rcar_write(p, INTCLR, BIT(hwirq));
+
+ spin_unlock_irqrestore(&p->lock, flags);
+}
+
+static int gpio_rcar_irq_set_type(struct irq_data *d, unsigned int type)
+{
+ struct gpio_rcar_priv *p = irq_data_get_irq_chip_data(d);
+ unsigned int hwirq = irqd_to_hwirq(d);
+
+ dev_dbg(&p->pdev->dev, "sense irq = %d, type = %d\n", hwirq, type);
+
+ switch (type & IRQ_TYPE_SENSE_MASK) {
+ case IRQ_TYPE_LEVEL_HIGH:
+ gpio_rcar_config_interrupt_input_mode(p, hwirq, true, true);
+ break;
+ case IRQ_TYPE_LEVEL_LOW:
+ gpio_rcar_config_interrupt_input_mode(p, hwirq, false, true);
+ break;
+ case IRQ_TYPE_EDGE_RISING:
+ gpio_rcar_config_interrupt_input_mode(p, hwirq, true, false);
+ break;
+ case IRQ_TYPE_EDGE_FALLING:
+ gpio_rcar_config_interrupt_input_mode(p, hwirq, false, false);
+ break;
+ default:
+ return -EINVAL;
+ }
+ return 0;
+}
+
+static irqreturn_t gpio_rcar_irq_handler(int irq, void *dev_id)
+{
+ struct gpio_rcar_priv *p = dev_id;
+ u32 pending;
+ unsigned int offset, irqs_handled = 0;
+
+ while ((pending = gpio_rcar_read(p, INTDT))) {
+ offset = __ffs(pending);
+ gpio_rcar_write(p, INTCLR, BIT(offset));
+ generic_handle_irq(irq_find_mapping(p->irq_domain, offset));
+ irqs_handled++;
+ }
+
+ return irqs_handled ? IRQ_HANDLED : IRQ_NONE;
+}
+
+static inline struct gpio_rcar_priv *gpio_to_priv(struct gpio_chip *chip)
+{
+ return container_of(chip, struct gpio_rcar_priv, gpio_chip);
+}
+
+static void gpio_rcar_config_general_input_output_mode(struct gpio_chip *chip,
+ unsigned int gpio,
+ bool output)
+{
+ struct gpio_rcar_priv *p = gpio_to_priv(chip);
+ unsigned long flags;
+
+ /* follow steps in the GPIO documentation for
+ * "Setting General Output Mode" and
+ * "Setting General Input Mode"
+ */
+
+ spin_lock_irqsave(&p->lock, flags);
+
+ /* Configure postive logic in POSNEG */
+ gpio_rcar_modify_bit(p, POSNEG, gpio, false);
+
+ /* Select "General Input/Output Mode" in IOINTSEL */
+ gpio_rcar_modify_bit(p, IOINTSEL, gpio, false);
+
+ /* Select Input Mode or Output Mode in INOUTSEL */
+ gpio_rcar_modify_bit(p, INOUTSEL, gpio, output);
+
+ spin_unlock_irqrestore(&p->lock, flags);
+}
+
+static int gpio_rcar_direction_input(struct gpio_chip *chip, unsigned offset)
+{
+ gpio_rcar_config_general_input_output_mode(chip, offset, false);
+ return 0;
+}
+
+static int gpio_rcar_get(struct gpio_chip *chip, unsigned offset)
+{
+ return (int)(gpio_rcar_read(gpio_to_priv(chip), INDT) & BIT(offset));
+}
+
+static void gpio_rcar_set(struct gpio_chip *chip, unsigned offset, int value)
+{
+ struct gpio_rcar_priv *p = gpio_to_priv(chip);
+ unsigned long flags;
+
+ spin_lock_irqsave(&p->lock, flags);
+ gpio_rcar_modify_bit(p, OUTDT, offset, value);
+ spin_unlock_irqrestore(&p->lock, flags);
+}
+
+static int gpio_rcar_direction_output(struct gpio_chip *chip, unsigned offset,
+ int value)
+{
+ /* write GPIO value to output before selecting output mode of pin */
+ gpio_rcar_set(chip, offset, value);
+ gpio_rcar_config_general_input_output_mode(chip, offset, true);
+ return 0;
+}
+
+static int gpio_rcar_to_irq(struct gpio_chip *chip, unsigned offset)
+{
+ return irq_create_mapping(gpio_to_priv(chip)->irq_domain, offset);
+}
+
+static int gpio_rcar_irq_domain_map(struct irq_domain *h, unsigned int virq,
+ irq_hw_number_t hw)
+{
+ struct gpio_rcar_priv *p = h->host_data;
+
+ dev_dbg(&p->pdev->dev, "map hw irq = %d, virq = %d\n", (int)hw, virq);
+
+ irq_set_chip_data(virq, h->host_data);
+ irq_set_chip_and_handler(virq, &p->irq_chip, handle_level_irq);
+ set_irq_flags(virq, IRQF_VALID); /* kill me now */
+ return 0;
+}
+
+static struct irq_domain_ops gpio_rcar_irq_domain_ops = {
+ .map = gpio_rcar_irq_domain_map,
+};
+
+static int gpio_rcar_probe(struct platform_device *pdev)
+{
+ struct gpio_rcar_config *pdata = pdev->dev.platform_data;
+ struct gpio_rcar_priv *p;
+ struct resource *io, *irq;
+ struct gpio_chip *gpio_chip;
+ struct irq_chip *irq_chip;
+ const char *name = dev_name(&pdev->dev);
+ int ret;
+
+ p = kzalloc(sizeof(*p), GFP_KERNEL);
+ if (!p) {
+ dev_err(&pdev->dev, "failed to allocate driver data\n");
+ ret = -ENOMEM;
+ goto err0;
+ }
+
+ /* deal with driver instance configuration */
+ if (pdata)
+ p->config = *pdata;
+
+ p->pdev = pdev;
+ platform_set_drvdata(pdev, p);
+ spin_lock_init(&p->lock);
+
+ io = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+
+ if (!io || !irq) {
+ dev_err(&pdev->dev, "missing IRQ or IOMEM\n");
+ ret = -EINVAL;
+ goto err1;
+ }
+
+ p->base = ioremap_nocache(io->start, resource_size(io));
+ if (!p->base) {
+ dev_err(&pdev->dev, "failed to remap I/O memory\n");
+ ret = -ENXIO;
+ goto err1;
+ }
+
+ gpio_chip = &p->gpio_chip;
+ gpio_chip->direction_input = gpio_rcar_direction_input;
+ gpio_chip->get = gpio_rcar_get;
+ gpio_chip->direction_output = gpio_rcar_direction_output;
+ gpio_chip->set = gpio_rcar_set;
+ gpio_chip->to_irq = gpio_rcar_to_irq;
+ gpio_chip->label = name;
+ gpio_chip->owner = THIS_MODULE;
+ gpio_chip->base = p->config.gpio_base;
+ gpio_chip->ngpio = p->config.number_of_pins;
+
+ irq_chip = &p->irq_chip;
+ irq_chip->name = name;
+ irq_chip->irq_mask = gpio_rcar_irq_disable;
+ irq_chip->irq_unmask = gpio_rcar_irq_enable;
+ irq_chip->irq_enable = gpio_rcar_irq_enable;
+ irq_chip->irq_disable = gpio_rcar_irq_disable;
+ irq_chip->irq_set_type = gpio_rcar_irq_set_type;
+ irq_chip->flags = IRQCHIP_SKIP_SET_WAKE;
+
+ p->irq_domain = irq_domain_add_simple(pdev->dev.of_node,
+ p->config.number_of_pins,
+ p->config.irq_base,
+ &gpio_rcar_irq_domain_ops, p);
+ if (!p->irq_domain) {
+ ret = -ENXIO;
+ dev_err(&pdev->dev, "cannot initialize irq domain\n");
+ goto err2;
+ }
+
+ if (request_irq(irq->start, gpio_rcar_irq_handler, 0, name, p)) {
+ dev_err(&pdev->dev, "failed to request IRQ\n");
+ ret = -ENOENT;
+ goto err3;
+ }
+
+ ret = gpiochip_add(gpio_chip);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to add GPIO controller\n");
+ goto err4;
+ }
+
+ dev_info(&pdev->dev, "driving %d GPIOs\n", p->config.number_of_pins);
+
+ /* warn in case of mismatch if irq base is specified */
+ if (p->config.irq_base) {
+ ret = irq_find_mapping(p->irq_domain, 0);
+ if (p->config.irq_base != ret)
+ dev_warn(&pdev->dev, "irq base mismatch (%u/%u)\n",
+ p->config.irq_base, ret);
+ }
+
+ return 0;
+
+err4:
+ free_irq(irq->start, p);
+err3:
+ irq_domain_remove(p->irq_domain);
+err2:
+ iounmap(p->base);
+err1:
+ kfree(p);
+err0:
+ return ret;
+}
+
+static int gpio_rcar_remove(struct platform_device *pdev)
+{
+ struct gpio_rcar_priv *p = platform_get_drvdata(pdev);
+ struct resource *irq;
+ int ret;
+
+ ret = gpiochip_remove(&p->gpio_chip);
+ if (ret)
+ return ret;
+
+ irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+
+ free_irq(irq->start, p);
+ irq_domain_remove(p->irq_domain);
+ iounmap(p->base);
+ kfree(p);
+ return 0;
+}
+
+static struct platform_driver gpio_rcar_device_driver = {
+ .probe = gpio_rcar_probe,
+ .remove = gpio_rcar_remove,
+ .driver = {
+ .name = "gpio_rcar",
+ }
+};
+
+module_platform_driver(gpio_rcar_device_driver);
+
+MODULE_AUTHOR("Magnus Damm");
+MODULE_DESCRIPTION("Renesas R-Car GPIO Driver");
+MODULE_LICENSE("GPL v2");
--- /dev/null
+++ work/include/linux/platform_data/gpio-rcar.h 2013-03-13 19:40:03.000000000 +0900
@@ -0,0 +1,25 @@
+/*
+ * Renesas R-Car GPIO Support
+ *
+ * Copyright (C) 2013 Magnus Damm
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __GPIO_RCAR_H__
+#define __GPIO_RCAR_H__
+
+struct gpio_rcar_config {
+ unsigned int gpio_base;
+ unsigned int irq_base;
+ unsigned int number_of_pins;
+};
+
+#endif /* __GPIO_RCAR_H__ */
From: Magnus Damm <[email protected]>
Set the flag IRQCHIP_SET_TYPE_MASKED in gpio-rcar.c to
force mask of the interrupt while configuring trigger
settings.
Signed-off-by: Magnus Damm <[email protected]>
---
drivers/gpio/gpio-rcar.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- 0004/drivers/gpio/gpio-rcar.c
+++ work/drivers/gpio/gpio-rcar.c 2013-03-13 19:42:56.000000000 +0900
@@ -301,7 +301,7 @@ static int gpio_rcar_probe(struct platfo
irq_chip->irq_enable = gpio_rcar_irq_enable;
irq_chip->irq_disable = gpio_rcar_irq_disable;
irq_chip->irq_set_type = gpio_rcar_irq_set_type;
- irq_chip->flags = IRQCHIP_SKIP_SET_WAKE;
+ irq_chip->flags = IRQCHIP_SKIP_SET_WAKE | IRQCHIP_SET_TYPE_MASKED;
p->irq_domain = irq_domain_add_simple(pdev->dev.of_node,
p->config.number_of_pins,
From: Magnus Damm <[email protected]>
Update the gpio-rcar.c driver to make use of devm
functions. This simplifies the error handling and
makes the code more compact.
Signed-off-by: Magnus Damm <[email protected]>
---
drivers/gpio/gpio-rcar.c | 32 +++++++++++---------------------
1 file changed, 11 insertions(+), 21 deletions(-)
--- 0005/drivers/gpio/gpio-rcar.c
+++ work/drivers/gpio/gpio-rcar.c 2013-03-13 19:47:17.000000000 +0900
@@ -252,7 +252,7 @@ static int gpio_rcar_probe(struct platfo
const char *name = dev_name(&pdev->dev);
int ret;
- p = kzalloc(sizeof(*p), GFP_KERNEL);
+ p = devm_kzalloc(&pdev->dev, sizeof(*p), GFP_KERNEL);
if (!p) {
dev_err(&pdev->dev, "failed to allocate driver data\n");
ret = -ENOMEM;
@@ -273,14 +273,15 @@ static int gpio_rcar_probe(struct platfo
if (!io || !irq) {
dev_err(&pdev->dev, "missing IRQ or IOMEM\n");
ret = -EINVAL;
- goto err1;
+ goto err0;
}
- p->base = ioremap_nocache(io->start, resource_size(io));
+ p->base = devm_ioremap_nocache(&pdev->dev, io->start,
+ resource_size(io));
if (!p->base) {
dev_err(&pdev->dev, "failed to remap I/O memory\n");
ret = -ENXIO;
- goto err1;
+ goto err0;
}
gpio_chip = &p->gpio_chip;
@@ -310,19 +311,20 @@ static int gpio_rcar_probe(struct platfo
if (!p->irq_domain) {
ret = -ENXIO;
dev_err(&pdev->dev, "cannot initialize irq domain\n");
- goto err2;
+ goto err1;
}
- if (request_irq(irq->start, gpio_rcar_irq_handler, 0, name, p)) {
+ if (devm_request_irq(&pdev->dev, irq->start,
+ gpio_rcar_irq_handler, 0, name, p)) {
dev_err(&pdev->dev, "failed to request IRQ\n");
ret = -ENOENT;
- goto err3;
+ goto err1;
}
ret = gpiochip_add(gpio_chip);
if (ret) {
dev_err(&pdev->dev, "failed to add GPIO controller\n");
- goto err4;
+ goto err1;
}
dev_info(&pdev->dev, "driving %d GPIOs\n", p->config.number_of_pins);
@@ -337,14 +339,8 @@ static int gpio_rcar_probe(struct platfo
return 0;
-err4:
- free_irq(irq->start, p);
-err3:
- irq_domain_remove(p->irq_domain);
-err2:
- iounmap(p->base);
err1:
- kfree(p);
+ irq_domain_remove(p->irq_domain);
err0:
return ret;
}
@@ -352,19 +348,13 @@ err0:
static int gpio_rcar_remove(struct platform_device *pdev)
{
struct gpio_rcar_priv *p = platform_get_drvdata(pdev);
- struct resource *irq;
int ret;
ret = gpiochip_remove(&p->gpio_chip);
if (ret)
return ret;
- irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
-
- free_irq(irq->start, p);
irq_domain_remove(p->irq_domain);
- iounmap(p->base);
- kfree(p);
return 0;
}
Hi Magnus,
Thanks for the patches.
On Wednesday 13 March 2013 20:32:03 Magnus Damm wrote:
> gpio: Renesas R-Car GPIO driver update
>
> [PATCH 01/03] gpio: Renesas R-Car GPIO driver V2
> [PATCH 02/03] gpio: rcar: Use IRQCHIP_SET_TYPE_MASKED
> [PATCH 03/03] gpio: rcar: Make use of devm functions
>
> This series updates the R-Car GPIO driver with various
> changes kindly suggested by Laurent Pinchart.
>
> Patch [01/03] is a drop in replacement for V1 of the R-Car
> GPIO driver. The flag in patch [02/03] is kept out of [01/03]
> to avoid changing the behaviour of the driver between V1 and V2.
> Also, devm support in [03/03] is kept out of [01/03] to make
> sure back porting goes as smooth as possible.
As I mentioned in a previous e-mail, all the devm_* functions used in 03/03
have been available since 2.6.30. Do you really need to port that driver to
older kernels ?
Regarding 02/03, do you plan to squash it with 01/03 for the mainline
submission ?
--
Regards,
Laurent Pinchart
Hi Magnus,
Thanks for the patch.
I've reviewed the result of squashing the 3 patches together, I just have one
comment.
On Wednesday 13 March 2013 20:32:13 Magnus Damm wrote:
> From: Magnus Damm <[email protected]>
>
> This patch is V2 of a GPIO driver for the R-Car series of
> SoCs from Renesas. This driver is designed to be reusable
> between multiple SoCs that share the same basic building block,
> but so far it has only been used on R-Car H1 (r8a7779).
>
> Each driver instance handles 32 GPIOs with individually
> maskable IRQs. The driver operates on a single I/O memory
> range and the 32 GPIOs are hooked up a single interrupt.
>
> In the case of R-Car H1 either external IRQ pins or GPIOs
> with interrupts can be used for on-board interupts. For
> external IRQs 4 pins are supported, and in the case of GPIO
> there are 202 GPIOS as 202 interrupts hooked up via 6 driver
> instances and to the GIC and the Cortex-A9 Quad.
>
> At this point this driver is interfacing as a regular
> platform device driver. In the future DT support will be
> submitted as an incremental feature patch.
>
> Signed-off-by: Magnus Damm <[email protected]>
> ---
>
> Changes since V1:
> - Update based on most suggestions from review by Laurent, thanks!
>
> Please note that in V2 the driver is reworked to reduce the number of
> lines and includes minor changes related to headers, printouts and
> data types. In V2 the register access order is kept the same as in V1,
> and to make that happen IRQCHIP_SET_TYPE_MASKED is omitted. The interface
> to the Linux kernel is unchanged except the use of dev_dbg() instead of
> pr_debug(). So from a hardware point of view V2 is a drop in replacement
> for V1 and there should be no additional dependencies since devm is
> kept as a separate patch as well. All this to make back porting easier.
>
> drivers/gpio/Kconfig | 6
> drivers/gpio/Makefile | 1
> drivers/gpio/gpio-rcar.c | 383 ++++++++++++++++++++++++++++
> include/linux/platform_data/gpio-rcar.h | 25 ++
> 4 files changed, 415 insertions(+)
[snip]
> --- /dev/null
> +++ work/drivers/gpio/gpio-rcar.c 2013-03-13 19:41:35.000000000 +0900
> @@ -0,0 +1,383 @@
> +/*
> + * Renesas R-Car GPIO Support
> + *
> + * Copyright (C) 2013 Magnus Damm
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
[snip]
> +static int gpio_rcar_irq_domain_map(struct irq_domain *h, unsigned int
> virq,
> + irq_hw_number_t hw)
> +{
> + struct gpio_rcar_priv *p = h->host_data;
> +
> + dev_dbg(&p->pdev->dev, "map hw irq = %d, virq = %d\n", (int)hw, virq);
> +
> + irq_set_chip_data(virq, h->host_data);
> + irq_set_chip_and_handler(virq, &p->irq_chip, handle_level_irq);
> + set_irq_flags(virq, IRQF_VALID); /* kill me now */
What is that comment about ?
> + return 0;
> +}
--
Regards,
Laurent Pinchart
On Wed, Mar 13, 2013 at 10:14 PM, Laurent Pinchart
<[email protected]> wrote:
> Hi Magnus,
>
> Thanks for the patch.
>
> I've reviewed the result of squashing the 3 patches together, I just have one
> comment.
>
> On Wednesday 13 March 2013 20:32:13 Magnus Damm wrote:
>> From: Magnus Damm <[email protected]>
>>
>> This patch is V2 of a GPIO driver for the R-Car series of
>> SoCs from Renesas. This driver is designed to be reusable
>> between multiple SoCs that share the same basic building block,
>> but so far it has only been used on R-Car H1 (r8a7779).
>>
>> Each driver instance handles 32 GPIOs with individually
>> maskable IRQs. The driver operates on a single I/O memory
>> range and the 32 GPIOs are hooked up a single interrupt.
>>
>> In the case of R-Car H1 either external IRQ pins or GPIOs
>> with interrupts can be used for on-board interupts. For
>> external IRQs 4 pins are supported, and in the case of GPIO
>> there are 202 GPIOS as 202 interrupts hooked up via 6 driver
>> instances and to the GIC and the Cortex-A9 Quad.
>>
>> At this point this driver is interfacing as a regular
>> platform device driver. In the future DT support will be
>> submitted as an incremental feature patch.
>>
>> Signed-off-by: Magnus Damm <[email protected]>
>> ---
>>
>> Changes since V1:
>> - Update based on most suggestions from review by Laurent, thanks!
>>
>> Please note that in V2 the driver is reworked to reduce the number of
>> lines and includes minor changes related to headers, printouts and
>> data types. In V2 the register access order is kept the same as in V1,
>> and to make that happen IRQCHIP_SET_TYPE_MASKED is omitted. The interface
>> to the Linux kernel is unchanged except the use of dev_dbg() instead of
>> pr_debug(). So from a hardware point of view V2 is a drop in replacement
>> for V1 and there should be no additional dependencies since devm is
>> kept as a separate patch as well. All this to make back porting easier.
>>
>> drivers/gpio/Kconfig | 6
>> drivers/gpio/Makefile | 1
>> drivers/gpio/gpio-rcar.c | 383 ++++++++++++++++++++++++++++
>> include/linux/platform_data/gpio-rcar.h | 25 ++
>> 4 files changed, 415 insertions(+)
>
> [snip]
>
>> --- /dev/null
>> +++ work/drivers/gpio/gpio-rcar.c 2013-03-13 19:41:35.000000000 +0900
>> @@ -0,0 +1,383 @@
>> +/*
>> + * Renesas R-Car GPIO Support
>> + *
>> + * Copyright (C) 2013 Magnus Damm
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License as published by
>> + * the Free Software Foundation; either version 2 of the License
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + */
>
> [snip]
>
>> +static int gpio_rcar_irq_domain_map(struct irq_domain *h, unsigned int
>> virq,
>> + irq_hw_number_t hw)
>> +{
>> + struct gpio_rcar_priv *p = h->host_data;
>> +
>> + dev_dbg(&p->pdev->dev, "map hw irq = %d, virq = %d\n", (int)hw, virq);
>> +
>> + irq_set_chip_data(virq, h->host_data);
>> + irq_set_chip_and_handler(virq, &p->irq_chip, handle_level_irq);
>> + set_irq_flags(virq, IRQF_VALID); /* kill me now */
>
> What is that comment about ?
I seem to have a habit of putting that comment in all IRQ code that I
write for ARM. See these threads for more info:
https://lkml.org/lkml/2013/2/19/246
http://lists.infradead.org/pipermail/linux-arm-kernel/2010-January/008795.html
Cheers,
/ magnus
Hi Laurent, Simon,
On Wed, Mar 13, 2013 at 9:58 PM, Laurent Pinchart
<[email protected]> wrote:
> Hi Magnus,
>
> Thanks for the patches.
Thanks for your review!
> On Wednesday 13 March 2013 20:32:03 Magnus Damm wrote:
>> gpio: Renesas R-Car GPIO driver update
>>
>> [PATCH 01/03] gpio: Renesas R-Car GPIO driver V2
>> [PATCH 02/03] gpio: rcar: Use IRQCHIP_SET_TYPE_MASKED
>> [PATCH 03/03] gpio: rcar: Make use of devm functions
>>
>> This series updates the R-Car GPIO driver with various
>> changes kindly suggested by Laurent Pinchart.
>>
>> Patch [01/03] is a drop in replacement for V1 of the R-Car
>> GPIO driver. The flag in patch [02/03] is kept out of [01/03]
>> to avoid changing the behaviour of the driver between V1 and V2.
>> Also, devm support in [03/03] is kept out of [01/03] to make
>> sure back porting goes as smooth as possible.
>
> As I mentioned in a previous e-mail, all the devm_* functions used in 03/03
> have been available since 2.6.30. Do you really need to port that driver to
> older kernels ?
Well, it was earlier suggested to me that not using devm to begin with
is a safe way forward for back porting. Also, as the individual patch
shows, we save about 10 lines of code but add many more complex
dependencies.
Simon, do you have any recommendation how for us regarding devm and
back porting?
> Regarding 02/03, do you plan to squash it with 01/03 for the mainline
> submission ?
Not unless someone puts a gun to my head. =) Of course, if a single
patch is really required then I will follow that, but I can't really
see why when we have a nice versioning control system that can help
our development in various ways.
What is the reason behind you wanting to merge these patches?
>From my point of view, if any incremental patch was a bug fix then i
would of course request to fold it in, but in this case these are
feature patches that would be beneficial to keep as individual
commits. Keeping them separate allows us to bisect and also makes
partial back porting easier if needed.
Thanks,
/ magnus
Hi Magnus,
On Thursday 14 March 2013 13:23:46 Magnus Damm wrote:
> On Wed, Mar 13, 2013 at 9:58 PM, Laurent Pinchart wrote:
> > On Wednesday 13 March 2013 20:32:03 Magnus Damm wrote:
> >> gpio: Renesas R-Car GPIO driver update
> >>
> >> [PATCH 01/03] gpio: Renesas R-Car GPIO driver V2
> >> [PATCH 02/03] gpio: rcar: Use IRQCHIP_SET_TYPE_MASKED
> >> [PATCH 03/03] gpio: rcar: Make use of devm functions
> >>
> >> This series updates the R-Car GPIO driver with various
> >> changes kindly suggested by Laurent Pinchart.
> >>
> >> Patch [01/03] is a drop in replacement for V1 of the R-Car
> >> GPIO driver. The flag in patch [02/03] is kept out of [01/03]
> >> to avoid changing the behaviour of the driver between V1 and V2.
> >> Also, devm support in [03/03] is kept out of [01/03] to make
> >> sure back porting goes as smooth as possible.
> >
> > As I mentioned in a previous e-mail, all the devm_* functions used in
> > 03/03 have been available since 2.6.30. Do you really need to port that
> > driver to older kernels ?
>
> Well, it was earlier suggested to me that not using devm to begin with
> is a safe way forward for back porting. Also, as the individual patch
> shows, we save about 10 lines of code but add many more complex
> dependencies.
>
> Simon, do you have any recommendation how for us regarding devm and
> back porting?
>
> > Regarding 02/03, do you plan to squash it with 01/03 for the mainline
> > submission ?
>
> Not unless someone puts a gun to my head. =) Of course, if a single
> patch is really required then I will follow that, but I can't really
> see why when we have a nice versioning control system that can help
> our development in various ways.
>
> What is the reason behind you wanting to merge these patches?
>
> From my point of view, if any incremental patch was a bug fix then i
> would of course request to fold it in, but in this case these are
> feature patches that would be beneficial to keep as individual
> commits. Keeping them separate allows us to bisect and also makes
> partial back porting easier if needed.
When submitting new drivers I usually try not to make the development history
visible to mainline. It brings little additional value (beside possibly making
backporting a bit easier, but in the devm_* case that shouldn't be a problem,
unless Simon thinks otherwise) but adds review complexity, as reviewers need
to validate the intermediate versions as well. More patches also mean more
potential bisection breakages.
In this case (assuming there would be no backporting issue) there's no need
for mainline to see that we started with a version that didn't use devm_* and
then modified the code. I see no added value in that.
--
Regards,
Laurent Pinchart
On Thu, Mar 14, 2013 at 02:13:52PM +0100, Laurent Pinchart wrote:
> Hi Magnus,
>
> On Thursday 14 March 2013 13:23:46 Magnus Damm wrote:
> > On Wed, Mar 13, 2013 at 9:58 PM, Laurent Pinchart wrote:
> > > On Wednesday 13 March 2013 20:32:03 Magnus Damm wrote:
> > >> gpio: Renesas R-Car GPIO driver update
> > >>
> > >> [PATCH 01/03] gpio: Renesas R-Car GPIO driver V2
> > >> [PATCH 02/03] gpio: rcar: Use IRQCHIP_SET_TYPE_MASKED
> > >> [PATCH 03/03] gpio: rcar: Make use of devm functions
> > >>
> > >> This series updates the R-Car GPIO driver with various
> > >> changes kindly suggested by Laurent Pinchart.
> > >>
> > >> Patch [01/03] is a drop in replacement for V1 of the R-Car
> > >> GPIO driver. The flag in patch [02/03] is kept out of [01/03]
> > >> to avoid changing the behaviour of the driver between V1 and V2.
> > >> Also, devm support in [03/03] is kept out of [01/03] to make
> > >> sure back porting goes as smooth as possible.
> > >
> > > As I mentioned in a previous e-mail, all the devm_* functions used in
> > > 03/03 have been available since 2.6.30. Do you really need to port that
> > > driver to older kernels ?
Not that I am aware of.
Actually, I am not aware of any serious back-porting to anything
older than LTSI-3.4.25.
> > Well, it was earlier suggested to me that not using devm to begin with
> > is a safe way forward for back porting. Also, as the individual patch
> > shows, we save about 10 lines of code but add many more complex
> > dependencies.
> >
> > Simon, do you have any recommendation how for us regarding devm and
> > back porting?
I see devm_* in LTSI-3.4.25 so unless I am missing something I don't
think there will be back-porting implications for you writing your
code against those functions.
> > > Regarding 02/03, do you plan to squash it with 01/03 for the mainline
> > > submission ?
> >
> > Not unless someone puts a gun to my head. =) Of course, if a single
> > patch is really required then I will follow that, but I can't really
> > see why when we have a nice versioning control system that can help
> > our development in various ways.
> >
> > What is the reason behind you wanting to merge these patches?
> >
> > From my point of view, if any incremental patch was a bug fix then i
> > would of course request to fold it in, but in this case these are
> > feature patches that would be beneficial to keep as individual
> > commits. Keeping them separate allows us to bisect and also makes
> > partial back porting easier if needed.
>
> When submitting new drivers I usually try not to make the development history
> visible to mainline. It brings little additional value (beside possibly making
> backporting a bit easier, but in the devm_* case that shouldn't be a problem,
> unless Simon thinks otherwise) but adds review complexity, as reviewers need
> to validate the intermediate versions as well. More patches also mean more
> potential bisection breakages.
>
> In this case (assuming there would be no backporting issue) there's no need
> for mainline to see that we started with a version that didn't use devm_* and
> then modified the code. I see no added value in that.
+1
Hi Laurent,
On Thu, Mar 14, 2013 at 10:13 PM, Laurent Pinchart
<[email protected]> wrote:
> Hi Magnus,
>
> On Thursday 14 March 2013 13:23:46 Magnus Damm wrote:
>> On Wed, Mar 13, 2013 at 9:58 PM, Laurent Pinchart wrote:
>> > On Wednesday 13 March 2013 20:32:03 Magnus Damm wrote:
>> >> gpio: Renesas R-Car GPIO driver update
>> >>
>> >> [PATCH 01/03] gpio: Renesas R-Car GPIO driver V2
>> >> [PATCH 02/03] gpio: rcar: Use IRQCHIP_SET_TYPE_MASKED
>> >> [PATCH 03/03] gpio: rcar: Make use of devm functions
>> >>
>> >> This series updates the R-Car GPIO driver with various
>> >> changes kindly suggested by Laurent Pinchart.
>> >>
>> >> Patch [01/03] is a drop in replacement for V1 of the R-Car
>> >> GPIO driver. The flag in patch [02/03] is kept out of [01/03]
>> >> to avoid changing the behaviour of the driver between V1 and V2.
>> >> Also, devm support in [03/03] is kept out of [01/03] to make
>> >> sure back porting goes as smooth as possible.
>> >
>> > As I mentioned in a previous e-mail, all the devm_* functions used in
>> > 03/03 have been available since 2.6.30. Do you really need to port that
>> > driver to older kernels ?
>>
>> Well, it was earlier suggested to me that not using devm to begin with
>> is a safe way forward for back porting. Also, as the individual patch
>> shows, we save about 10 lines of code but add many more complex
>> dependencies.
>>
>> Simon, do you have any recommendation how for us regarding devm and
>> back porting?
>>
>> > Regarding 02/03, do you plan to squash it with 01/03 for the mainline
>> > submission ?
>>
>> Not unless someone puts a gun to my head. =) Of course, if a single
>> patch is really required then I will follow that, but I can't really
>> see why when we have a nice versioning control system that can help
>> our development in various ways.
>>
>> What is the reason behind you wanting to merge these patches?
>>
>> From my point of view, if any incremental patch was a bug fix then i
>> would of course request to fold it in, but in this case these are
>> feature patches that would be beneficial to keep as individual
>> commits. Keeping them separate allows us to bisect and also makes
>> partial back porting easier if needed.
>
> When submitting new drivers I usually try not to make the development history
> visible to mainline. It brings little additional value (beside possibly making
> backporting a bit easier, but in the devm_* case that shouldn't be a problem,
> unless Simon thinks otherwise) but adds review complexity, as reviewers need
> to validate the intermediate versions as well. More patches also mean more
> potential bisection breakages.
Huh, it seems that my point of view is the total opposite. I see that
using incremental patches to show new development would make review
_easier_. Perhaps that's not the case for most people.
Regarding bisection, having features broken out actually allows us to
bisect compared to a single commit. I see that as a feature. Of course
the developer needs to make sure that the incremental changes do not
cause any breakages, but if the developer can't do that then there are
other more serious issues that need to be fixed IMO.
> In this case (assuming there would be no backporting issue) there's no need
> for mainline to see that we started with a version that didn't use devm_* and
> then modified the code. I see no added value in that.
So say that you write a driver and add say 8 features on top of that
over time, wouldn't it make sense to share that information with other
people? That way any party can bisect and locate issues that may come
up. I find that useful regardless if the code is back ported or not.
Anyway, with this particular driver it doesn't really matter since the
complexity is very low. And now Simon has gotten back to us with
updated information about back porting.
I will pull it all together into a V3.
Thanks,
/ magnus
Hi Magnus,
On Tuesday 19 March 2013 12:36:52 Magnus Damm wrote:
> On Thu, Mar 14, 2013 at 10:13 PM, Laurent Pinchart wrote:
> > On Thursday 14 March 2013 13:23:46 Magnus Damm wrote:
> >> On Wed, Mar 13, 2013 at 9:58 PM, Laurent Pinchart wrote:
> >> > On Wednesday 13 March 2013 20:32:03 Magnus Damm wrote:
> >> >> gpio: Renesas R-Car GPIO driver update
> >> >>
> >> >> [PATCH 01/03] gpio: Renesas R-Car GPIO driver V2
> >> >> [PATCH 02/03] gpio: rcar: Use IRQCHIP_SET_TYPE_MASKED
> >> >> [PATCH 03/03] gpio: rcar: Make use of devm functions
> >> >>
> >> >> This series updates the R-Car GPIO driver with various
> >> >> changes kindly suggested by Laurent Pinchart.
> >> >>
> >> >> Patch [01/03] is a drop in replacement for V1 of the R-Car
> >> >> GPIO driver. The flag in patch [02/03] is kept out of [01/03]
> >> >> to avoid changing the behaviour of the driver between V1 and V2.
> >> >> Also, devm support in [03/03] is kept out of [01/03] to make
> >> >> sure back porting goes as smooth as possible.
> >> >
> >> > As I mentioned in a previous e-mail, all the devm_* functions used in
> >> > 03/03 have been available since 2.6.30. Do you really need to port that
> >> > driver to older kernels ?
> >>
> >> Well, it was earlier suggested to me that not using devm to begin with
> >> is a safe way forward for back porting. Also, as the individual patch
> >> shows, we save about 10 lines of code but add many more complex
> >> dependencies.
> >>
> >> Simon, do you have any recommendation how for us regarding devm and
> >> back porting?
> >>
> >> > Regarding 02/03, do you plan to squash it with 01/03 for the mainline
> >> > submission ?
> >>
> >> Not unless someone puts a gun to my head. =) Of course, if a single
> >> patch is really required then I will follow that, but I can't really
> >> see why when we have a nice versioning control system that can help
> >> our development in various ways.
> >>
> >> What is the reason behind you wanting to merge these patches?
> >>
> >> From my point of view, if any incremental patch was a bug fix then i
> >> would of course request to fold it in, but in this case these are
> >> feature patches that would be beneficial to keep as individual
> >> commits. Keeping them separate allows us to bisect and also makes
> >> partial back porting easier if needed.
> >
> > When submitting new drivers I usually try not to make the development
> > history visible to mainline. It brings little additional value (beside
> > possibly making backporting a bit easier, but in the devm_* case that
> > shouldn't be a problem, unless Simon thinks otherwise) but adds review
> > complexity, as reviewers need to validate the intermediate versions as
> > well. More patches also mean more potential bisection breakages.
>
> Huh, it seems that my point of view is the total opposite. I see that
> using incremental patches to show new development would make review
> _easier_. Perhaps that's not the case for most people.
>
> Regarding bisection, having features broken out actually allows us to
> bisect compared to a single commit. I see that as a feature. Of course
> the developer needs to make sure that the incremental changes do not
> cause any breakages, but if the developer can't do that then there are
> other more serious issues that need to be fixed IMO.
>
> > In this case (assuming there would be no backporting issue) there's no
> > need for mainline to see that we started with a version that didn't use
> > devm_* and then modified the code. I see no added value in that.
>
> So say that you write a driver and add say 8 features on top of that
> over time, wouldn't it make sense to share that information with other
> people? That way any party can bisect and locate issues that may come
> up. I find that useful regardless if the code is back ported or not.
Long answer short: it depends :-)
If you add features incrementally, submitting them as individual patches
totally make sense. However, if your patches aim at simplifying the code
instead of adding features (such as devm_* usage), individual patches make it
more complex in my opinion. Reviewers will need to look at the intermediate,
more complex code, to make sure that no bisection breakage points will be
introduced. Squashing the patches together then make review easier (as there's
less code to review) and don't really hurt bisection, as the simplification
patches usually remove code and thus bugs.
> Anyway, with this particular driver it doesn't really matter since the
> complexity is very low. And now Simon has gotten back to us with updated
> information about back porting.
>
> I will pull it all together into a V3.
Thank you :-)
--
Regards,
Laurent Pinchart
On Tue, Mar 19, 2013 at 4:36 AM, Magnus Damm <[email protected]> wrote:
> On Thu, Mar 14, 2013 at 10:13 PM, Laurent Pinchart
> <[email protected]> wrote:
>> When submitting new drivers I usually try not to make the development history
>> visible to mainline. It brings little additional value (beside possibly making
>> backporting a bit easier, but in the devm_* case that shouldn't be a problem,
>> unless Simon thinks otherwise) but adds review complexity, as reviewers need
>> to validate the intermediate versions as well. More patches also mean more
>> potential bisection breakages.
>
> Huh, it seems that my point of view is the total opposite. I see that
> using incremental patches to show new development would make review
> _easier_. Perhaps that's not the case for most people.
As subsystem maintainer what I don't want to see is a patch that
at one point breaks something in some configuration and then later
fixes it. Then I strongly prefer squashing. (Greg also mentions this
in one of his seminars.)
What really makes me mad is the the above pattern + claim that
it must be done in that way to preserve authorship. Like legaleaze
or credit is more important that functionality.
If all patches are bisectable and perfectly fine then whether you
take 8 stops when driving to Rome or just drive there in one
big stretch is more a technical, secondary thing. Do whatever you
like as long as all commits build and boot.
Yours,
Linus Walleij
On Wed, Mar 27, 2013 at 9:34 PM, Linus Walleij <[email protected]> wrote:
> On Tue, Mar 19, 2013 at 4:36 AM, Magnus Damm <[email protected]> wrote:
>> On Thu, Mar 14, 2013 at 10:13 PM, Laurent Pinchart
>> <[email protected]> wrote:
>
>>> When submitting new drivers I usually try not to make the development history
>>> visible to mainline. It brings little additional value (beside possibly making
>>> backporting a bit easier, but in the devm_* case that shouldn't be a problem,
>>> unless Simon thinks otherwise) but adds review complexity, as reviewers need
>>> to validate the intermediate versions as well. More patches also mean more
>>> potential bisection breakages.
>>
>> Huh, it seems that my point of view is the total opposite. I see that
>> using incremental patches to show new development would make review
>> _easier_. Perhaps that's not the case for most people.
>
> As subsystem maintainer what I don't want to see is a patch that
> at one point breaks something in some configuration and then later
> fixes it. Then I strongly prefer squashing. (Greg also mentions this
> in one of his seminars.)
Sure, I totally agree. I strongly dislike when people introduce
breakage and then fix it later in the same series. It's pretty obvious
to me, each incremental step needs to work by itself - if it doesn't
then it should be reworked before it gets merged. I personally prefer
to separate features from fixes. Fixes are always folded into the
original patch.
> What really makes me mad is the the above pattern + claim that
> it must be done in that way to preserve authorship. Like legaleaze
> or credit is more important that functionality.
>
> If all patches are bisectable and perfectly fine then whether you
> take 8 stops when driving to Rome or just drive there in one
> big stretch is more a technical, secondary thing. Do whatever you
> like as long as all commits build and boot.
I suppose I prefer to stop for coffee in every village then. =)
/ magnus