The vbus regulator was not getting its name set. This results
in the sysfs entry being empty. The lack of a bcm590xx_regs[]
table entry also upsets Coverity runs. Add the table entry
so the name gets set properly.
Signed-off-by: Graham Williams <[email protected]>
---
drivers/regulator/bcm590xx-regulator.c | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/drivers/regulator/bcm590xx-regulator.c b/drivers/regulator/bcm590xx-regulator.c
index 57544e2..58ece59 100644
--- a/drivers/regulator/bcm590xx-regulator.c
+++ b/drivers/regulator/bcm590xx-regulator.c
@@ -119,6 +119,10 @@ static const unsigned int ldo_c_table[] = {
2900000, 3000000, 3300000,
};
+static const unsigned int ldo_vbus[] = {
+ 5000000,
+};
+
/* DCDC group CSR: supported voltages in microvolts */
static const struct regulator_linear_range dcdc_csr_ranges[] = {
REGULATOR_LINEAR_RANGE(860000, 2, 50, 10000),
@@ -192,6 +196,7 @@ static struct bcm590xx_info bcm590xx_regs[] = {
BCM590XX_REG_TABLE(gpldo4, ldo_a_table),
BCM590XX_REG_TABLE(gpldo5, ldo_a_table),
BCM590XX_REG_TABLE(gpldo6, ldo_a_table),
+ BCM590XX_REG_TABLE(vbus, ldo_vbus),
};
struct bcm590xx_reg {
--
1.7.9.5
On Wed, Jun 18, 2014 at 12:42:10PM -0700, Graham Williams wrote:
> The vbus regulator was not getting its name set. This results
> in the sysfs entry being empty. The lack of a bcm590xx_regs[]
> table entry also upsets Coverity runs. Add the table entry
> so the name gets set properly.
>
> Signed-off-by: Graham Williams <[email protected]>
> ---
> drivers/regulator/bcm590xx-regulator.c | 5 +++++
> 1 file changed, 5 insertions(+)
>
> diff --git a/drivers/regulator/bcm590xx-regulator.c b/drivers/regulator/bcm590xx-regulator.c
> index 57544e2..58ece59 100644
> --- a/drivers/regulator/bcm590xx-regulator.c
> +++ b/drivers/regulator/bcm590xx-regulator.c
> @@ -119,6 +119,10 @@ static const unsigned int ldo_c_table[] = {
> 2900000, 3000000, 3300000,
> };
>
> +static const unsigned int ldo_vbus[] = {
> + 5000000,
> +};
> +
> /* DCDC group CSR: supported voltages in microvolts */
> static const struct regulator_linear_range dcdc_csr_ranges[] = {
> REGULATOR_LINEAR_RANGE(860000, 2, 50, 10000),
> @@ -192,6 +196,7 @@ static struct bcm590xx_info bcm590xx_regs[] = {
> BCM590XX_REG_TABLE(gpldo4, ldo_a_table),
> BCM590XX_REG_TABLE(gpldo5, ldo_a_table),
> BCM590XX_REG_TABLE(gpldo6, ldo_a_table),
> + BCM590XX_REG_TABLE(vbus, ldo_vbus),
> };
Also fixes the functional problem for me on the Capri board, thanks.
Coverity should also be much happier now.
Acked-by: Matt Porter <[email protected]>
Mark: can you pick this up for 3.16 fixes?
-Matt
On Wed, Jun 18, 2014 at 12:42:10PM -0700, Graham Williams wrote:
> The vbus regulator was not getting its name set. This results
> in the sysfs entry being empty. The lack of a bcm590xx_regs[]
> table entry also upsets Coverity runs. Add the table entry
> so the name gets set properly.
Applied, thanks.