There is no need to change the 802.1Q port mode for the same value.
Thus avoid such message:
[ 401.954836] dsa dsa@0 lan0: 802.1Q Mode: Disabled (was Disabled)
Signed-off-by: Vivien Didelot <[email protected]>
---
drivers/net/dsa/mv88e6xxx.c | 21 +++++++++++++--------
1 file changed, 13 insertions(+), 8 deletions(-)
diff --git a/drivers/net/dsa/mv88e6xxx.c b/drivers/net/dsa/mv88e6xxx.c
index 1aee42d..5f07524 100644
--- a/drivers/net/dsa/mv88e6xxx.c
+++ b/drivers/net/dsa/mv88e6xxx.c
@@ -1765,16 +1765,21 @@ int mv88e6xxx_port_vlan_filtering(struct dsa_switch *ds, int port,
old = ret & PORT_CONTROL_2_8021Q_MASK;
- ret &= ~PORT_CONTROL_2_8021Q_MASK;
- ret |= new & PORT_CONTROL_2_8021Q_MASK;
+ if (new != old) {
+ ret &= ~PORT_CONTROL_2_8021Q_MASK;
+ ret |= new & PORT_CONTROL_2_8021Q_MASK;
- ret = _mv88e6xxx_reg_write(ds, REG_PORT(port), PORT_CONTROL_2, ret);
- if (ret < 0)
- goto unlock;
+ ret = _mv88e6xxx_reg_write(ds, REG_PORT(port), PORT_CONTROL_2,
+ ret);
+ if (ret < 0)
+ goto unlock;
+
+ netdev_dbg(ds->ports[port], "802.1Q Mode %s (was %s)\n",
+ mv88e6xxx_port_8021q_mode_names[new],
+ mv88e6xxx_port_8021q_mode_names[old]);
+ }
- netdev_dbg(ds->ports[port], "802.1Q Mode: %s (was %s)\n",
- mv88e6xxx_port_8021q_mode_names[new],
- mv88e6xxx_port_8021q_mode_names[old]);
+ ret = 0;
unlock:
mutex_unlock(&ps->smi_mutex);
--
2.7.2
On Mon, Mar 07, 2016 at 06:24:52PM -0500, Vivien Didelot wrote:
> There is no need to change the 802.1Q port mode for the same value.
> Thus avoid such message:
>
> [ 401.954836] dsa dsa@0 lan0: 802.1Q Mode: Disabled (was Disabled)
>
> Signed-off-by: Vivien Didelot <[email protected]>
Tested-by: Andrew Lunn <[email protected]>
Thanks
Andrew
> ---
> drivers/net/dsa/mv88e6xxx.c | 21 +++++++++++++--------
> 1 file changed, 13 insertions(+), 8 deletions(-)
>
> diff --git a/drivers/net/dsa/mv88e6xxx.c b/drivers/net/dsa/mv88e6xxx.c
> index 1aee42d..5f07524 100644
> --- a/drivers/net/dsa/mv88e6xxx.c
> +++ b/drivers/net/dsa/mv88e6xxx.c
> @@ -1765,16 +1765,21 @@ int mv88e6xxx_port_vlan_filtering(struct dsa_switch *ds, int port,
>
> old = ret & PORT_CONTROL_2_8021Q_MASK;
>
> - ret &= ~PORT_CONTROL_2_8021Q_MASK;
> - ret |= new & PORT_CONTROL_2_8021Q_MASK;
> + if (new != old) {
> + ret &= ~PORT_CONTROL_2_8021Q_MASK;
> + ret |= new & PORT_CONTROL_2_8021Q_MASK;
>
> - ret = _mv88e6xxx_reg_write(ds, REG_PORT(port), PORT_CONTROL_2, ret);
> - if (ret < 0)
> - goto unlock;
> + ret = _mv88e6xxx_reg_write(ds, REG_PORT(port), PORT_CONTROL_2,
> + ret);
> + if (ret < 0)
> + goto unlock;
> +
> + netdev_dbg(ds->ports[port], "802.1Q Mode %s (was %s)\n",
> + mv88e6xxx_port_8021q_mode_names[new],
> + mv88e6xxx_port_8021q_mode_names[old]);
> + }
>
> - netdev_dbg(ds->ports[port], "802.1Q Mode: %s (was %s)\n",
> - mv88e6xxx_port_8021q_mode_names[new],
> - mv88e6xxx_port_8021q_mode_names[old]);
> + ret = 0;
> unlock:
> mutex_unlock(&ps->smi_mutex);
>
> --
> 2.7.2
>
From: Vivien Didelot <[email protected]>
Date: Mon, 7 Mar 2016 18:24:52 -0500
> There is no need to change the 802.1Q port mode for the same value.
> Thus avoid such message:
>
> [ 401.954836] dsa dsa@0 lan0: 802.1Q Mode: Disabled (was Disabled)
>
> Signed-off-by: Vivien Didelot <[email protected]>
Applied.