From: Xinming Hu <[email protected]>
Add device tree binding documentation for MARVELL's bluetooth sdio
(sd8897 and sd8997) chip.
Signed-off-by: Xinming Hu <[email protected]>
Signed-off-by: Amitkumar Karwar <[email protected]>
---
Listing changelist for both 1/2 and 2/2 here
v2: Fixed build error reported by kbuild test robot
drivers/bluetooth/btmrvl_platform.c:141:22: error:
'btmrvl_plt_pm_ops' undeclared here (not in a function)
v3: Add NULL check for 'btmrvl_plt_dev'
v4: Moved the bindings file to bindings/net/
Corrected the name of 'name' and 'compatible' properties(Rob Herring)
v5: Comments for wlan patches were applicable here as well. Like all binding
changes in single file, specifying node as a child of SDIO controller.
v6: a)Use <chip>-bt order for compatible attribute(Rob Herring)
b)Split wakeuppin-gap to wakeup-pin and wakeup-gap(Rob Herring)
c)Use sdio function number for both the unit address and reg(Rob Herring)
v7: a)Use suggested vendor name and generic node name(Rob Herring)
v8: a)Nodes are renamed as per suggestions from Rob Herring
btmrvl,* -> marvell,*
"wakeup-gap-msec" -> "wakeup-gap-ms"
---
Documentation/devicetree/bindings/btmrvl.txt | 29 -----------
.../devicetree/bindings/net/marvell-bt-sd8xxx.txt | 56 ++++++++++++++++++++++
2 files changed, 56 insertions(+), 29 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/btmrvl.txt
create mode 100644 Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt
diff --git a/Documentation/devicetree/bindings/btmrvl.txt b/Documentation/devicetree/bindings/btmrvl.txt
deleted file mode 100644
index 58f964b..0000000
--- a/Documentation/devicetree/bindings/btmrvl.txt
+++ /dev/null
@@ -1,29 +0,0 @@
-btmrvl
-------
-
-Required properties:
-
- - compatible : must be "btmrvl,cfgdata"
-
-Optional properties:
-
- - btmrvl,cal-data : Calibration data downloaded to the device during
- initialization. This is an array of 28 values(u8).
-
- - btmrvl,gpio-gap : gpio and gap (in msecs) combination to be
- configured.
-
-Example:
-
-GPIO pin 13 is configured as a wakeup source and GAP is set to 100 msecs
-in below example.
-
-btmrvl {
- compatible = "btmrvl,cfgdata";
-
- btmrvl,cal-data = /bits/ 8 <
- 0x37 0x01 0x1c 0x00 0xff 0xff 0xff 0xff 0x01 0x7f 0x04 0x02
- 0x00 0x00 0xba 0xce 0xc0 0xc6 0x2d 0x00 0x00 0x00 0x00 0x00
- 0x00 0x00 0xf0 0x00>;
- btmrvl,gpio-gap = <0x0d64>;
-};
diff --git a/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt b/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt
new file mode 100644
index 0000000..14aa6cf
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt
@@ -0,0 +1,56 @@
+Marvell 8897/8997 (sd8897/sd8997) bluetooth SDIO devices
+------
+
+Required properties:
+
+ - compatible : should be one of the following:
+ * "marvell,sd8897-bt"
+ * "marvell,sd8997-bt"
+
+Optional properties:
+
+ - marvell,cal-data: Calibration data downloaded to the device during
+ initialization. This is an array of 28 values(u8).
+
+ - marvell,wakeup-pin: It represents wakeup pin number of the bluetooth chip.
+ firmware will use the pin to wakeup host system.
+ - marvell,wakeup-gap-ms: wakeup gap represents wakeup latency of the host
+ platform. The value will be configured to firmware. This
+ is needed to work chip's sleep feature as expected.
+ - interrupt-parent: phandle of the parent interrupt controller
+ - interrupts : interrupt pin number to the cpu. Driver will request an irq based
+ on this interrupt number. During system suspend, the irq will be
+ enabled so that the bluetooth chip can wakeup host platform under
+ certain condition. During system resume, the irq will be disabled
+ to make sure unnecessary interrupt is not received.
+
+Example:
+
+IRQ pin 119 is used as system wakeup source interrupt.
+wakeup pin 13 and gap 100ms are configured so that firmware can wakeup host
+using this device side pin and wakeup latency.
+calibration data is also available in below example.
+
+&mmc3 {
+ status = "okay";
+ vmmc-supply = <&wlan_en_reg>;
+ bus-width = <4>;
+ cap-power-off-card;
+ keep-power-in-suspend;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ btmrvl: bluetooth@2 {
+ compatible = "marvell,sd8897-bt";
+ reg = <2>;
+ interrupt-parent = <&pio>;
+ interrupts = <119 IRQ_TYPE_LEVEL_LOW>;
+
+ marvell,cal-data = /bits/ 8 <
+ 0x37 0x01 0x1c 0x00 0xff 0xff 0xff 0xff 0x01 0x7f 0x04 0x02
+ 0x00 0x00 0xba 0xce 0xc0 0xc6 0x2d 0x00 0x00 0x00 0x00 0x00
+ 0x00 0x00 0xf0 0x00>;
+ marvell,wakeup-pin = <0x0d>;
+ marvell,wakeup-gap-ms = <0x64>;
+ };
+};
--
1.8.1.4
From: Xinming Hu <[email protected]>
On some arm-based platforms, we need to configure platform specific
parameters by device tree node and also define our node as a child
node of parent SDIO host controller.
This patch parses these parameters from device tree. It includes
calibration data download to firmware, wakeup pin configured to firmware,
and soc specific wake up gpio, which will be set as wakeup interrupt pin.
Signed-off-by: Xinming Hu <[email protected]>
Signed-off-by: Amitkumar Karwar <[email protected]>
---
drivers/bluetooth/btmrvl_drv.h | 11 ++++++
drivers/bluetooth/btmrvl_main.c | 35 ++++++++++--------
drivers/bluetooth/btmrvl_sdio.c | 79 +++++++++++++++++++++++++++++++++++++++++
drivers/bluetooth/btmrvl_sdio.h | 6 ++++
4 files changed, 116 insertions(+), 15 deletions(-)
diff --git a/drivers/bluetooth/btmrvl_drv.h b/drivers/bluetooth/btmrvl_drv.h
index 0590473..f742384 100644
--- a/drivers/bluetooth/btmrvl_drv.h
+++ b/drivers/bluetooth/btmrvl_drv.h
@@ -23,6 +23,17 @@
#include <linux/bitops.h>
#include <linux/slab.h>
#include <net/bluetooth/bluetooth.h>
+#include <linux/err.h>
+#include <linux/gpio.h>
+#include <linux/gfp.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/of_gpio.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/slab.h>
+#include <linux/of_irq.h>
#define BTM_HEADER_LEN 4
#define BTM_UPLD_SIZE 2312
diff --git a/drivers/bluetooth/btmrvl_main.c b/drivers/bluetooth/btmrvl_main.c
index f25a825..7ad8d61 100644
--- a/drivers/bluetooth/btmrvl_main.c
+++ b/drivers/bluetooth/btmrvl_main.c
@@ -510,34 +510,39 @@ static int btmrvl_download_cal_data(struct btmrvl_private *priv,
static int btmrvl_check_device_tree(struct btmrvl_private *priv)
{
struct device_node *dt_node;
+ struct btmrvl_sdio_card *card = priv->btmrvl_dev.card;
u8 cal_data[BT_CAL_HDR_LEN + BT_CAL_DATA_SIZE];
- int ret;
- u32 val;
+ int ret = 0;
+ u16 gpio, gap;
+
+ if (card->plt_of_node) {
+ dt_node = card->plt_of_node;
+ ret = of_property_read_u16(dt_node, "marvell,wakeup-pin",
+ &gpio);
+ if (ret)
+ gpio = (priv->btmrvl_dev.gpio_gap & 0xff00) >> 8;
+
+ ret = of_property_read_u16(dt_node, "marvell,wakeup-gap-ms",
+ &gap);
+ if (ret)
+ gap = (u8)(priv->btmrvl_dev.gpio_gap & 0x00ff);
- for_each_compatible_node(dt_node, NULL, "btmrvl,cfgdata") {
- ret = of_property_read_u32(dt_node, "btmrvl,gpio-gap", &val);
- if (!ret)
- priv->btmrvl_dev.gpio_gap = val;
+ priv->btmrvl_dev.gpio_gap = (gpio << 8) + gap;
- ret = of_property_read_u8_array(dt_node, "btmrvl,cal-data",
+ ret = of_property_read_u8_array(dt_node, "marvell,cal-data",
cal_data + BT_CAL_HDR_LEN,
BT_CAL_DATA_SIZE);
- if (ret) {
- of_node_put(dt_node);
+ if (ret)
return ret;
- }
BT_DBG("Use cal data from device tree");
ret = btmrvl_download_cal_data(priv, cal_data,
BT_CAL_DATA_SIZE);
- if (ret) {
+ if (ret)
BT_ERR("Fail to download calibrate data");
- of_node_put(dt_node);
- return ret;
- }
}
- return 0;
+ return ret;
}
static int btmrvl_setup(struct hci_dev *hdev)
diff --git a/drivers/bluetooth/btmrvl_sdio.c b/drivers/bluetooth/btmrvl_sdio.c
index c6ef248..4961318 100644
--- a/drivers/bluetooth/btmrvl_sdio.c
+++ b/drivers/bluetooth/btmrvl_sdio.c
@@ -52,6 +52,68 @@ static struct memory_type_mapping mem_type_mapping_tbl[] = {
{"EXTLAST", NULL, 0, 0xFE},
};
+static const struct of_device_id btmrvl_sdio_of_match_table[] = {
+ { .compatible = "marvell,sd8897-bt" },
+ { .compatible = "marvell,sd8997-bt" },
+ { }
+};
+
+static irqreturn_t btmrvl_wake_irq_bt(int irq, void *priv)
+{
+ struct btmrvl_plt_wake_cfg *cfg = priv;
+
+ if (cfg->irq_bt >= 0) {
+ pr_info("%s: wake by bt", __func__);
+ cfg->wake_by_bt = true;
+ disable_irq_nosync(irq);
+ }
+
+ return IRQ_HANDLED;
+}
+
+/* This function parses device tree node using mmc subnode devicetree API.
+ * The device node is saved in card->plt_of_node.
+ * If the device tree node exists and includes interrupts attributes, this
+ * function will request platform specific wakeup interrupt.
+ */
+static int btmrvl_sdio_probe_of(struct device *dev,
+ struct btmrvl_sdio_card *card)
+{
+ struct btmrvl_plt_wake_cfg *cfg;
+ int ret;
+
+ if (!dev->of_node ||
+ !of_match_node(btmrvl_sdio_of_match_table, dev->of_node)) {
+ pr_err("sdio platform data not available");
+ return -1;
+ }
+
+ card->plt_of_node = dev->of_node;
+
+ card->plt_wake_cfg = devm_kzalloc(dev, sizeof(*card->plt_wake_cfg),
+ GFP_KERNEL);
+ cfg = card->plt_wake_cfg;
+ if (cfg && card->plt_of_node) {
+ cfg->irq_bt = irq_of_parse_and_map(card->plt_of_node, 0);
+ if (!cfg->irq_bt) {
+ dev_err(dev, "fail to parse irq_bt from device tree");
+ } else {
+ ret = devm_request_irq(dev, cfg->irq_bt,
+ btmrvl_wake_irq_bt,
+ IRQF_TRIGGER_LOW,
+ "bt_wake", cfg);
+ if (ret) {
+ dev_err(dev,
+ "Failed to request irq_bt %d (%d)\n",
+ cfg->irq_bt, ret);
+ }
+ disable_irq(cfg->irq_bt);
+ }
+ }
+
+ return 0;
+}
+
/* The btmrvl_sdio_remove() callback function is called
* when user removes this module from kernel space or ejects
* the card from the slot. The driver handles these 2 cases
@@ -1464,6 +1526,9 @@ static int btmrvl_sdio_probe(struct sdio_func *func,
btmrvl_sdio_enable_host_int(card);
+ /* Device tree node parsing and platform specific configuration*/
+ btmrvl_sdio_probe_of(&func->dev, card);
+
priv = btmrvl_add_card(card);
if (!priv) {
BT_ERR("Initializing card failed!");
@@ -1544,6 +1609,13 @@ static int btmrvl_sdio_suspend(struct device *dev)
return 0;
}
+ /* Enable platform specific wakeup interrupt */
+ if (card->plt_wake_cfg && card->plt_wake_cfg->irq_bt >= 0) {
+ card->plt_wake_cfg->wake_by_bt = false;
+ enable_irq(card->plt_wake_cfg->irq_bt);
+ enable_irq_wake(card->plt_wake_cfg->irq_bt);
+ }
+
priv = card->priv;
priv->adapter->is_suspending = true;
hcidev = priv->btmrvl_dev.hcidev;
@@ -1606,6 +1678,13 @@ static int btmrvl_sdio_resume(struct device *dev)
BT_DBG("%s: SDIO resume", hcidev->name);
hci_resume_dev(hcidev);
+ /* Disable platform specific wakeup interrupt */
+ if (card->plt_wake_cfg && card->plt_wake_cfg->irq_bt >= 0) {
+ disable_irq_wake(card->plt_wake_cfg->irq_bt);
+ if (!card->plt_wake_cfg->wake_by_bt)
+ disable_irq(card->plt_wake_cfg->irq_bt);
+ }
+
return 0;
}
diff --git a/drivers/bluetooth/btmrvl_sdio.h b/drivers/bluetooth/btmrvl_sdio.h
index 1a3bd06..3a522d2 100644
--- a/drivers/bluetooth/btmrvl_sdio.h
+++ b/drivers/bluetooth/btmrvl_sdio.h
@@ -62,6 +62,10 @@
#define FIRMWARE_READY 0xfedc
+struct btmrvl_plt_wake_cfg {
+ int irq_bt;
+ bool wake_by_bt;
+};
struct btmrvl_sdio_card_reg {
u8 cfg;
@@ -97,6 +101,8 @@ struct btmrvl_sdio_card {
u16 sd_blksz_fw_dl;
u8 rx_unit;
struct btmrvl_private *priv;
+ struct device_node *plt_of_node;
+ struct btmrvl_plt_wake_cfg *plt_wake_cfg;
};
struct btmrvl_sdio_device {
--
1.8.1.4
On Tue, Apr 26, 2016 at 06:57:26AM -0700, Amitkumar Karwar wrote:
> From: Xinming Hu <[email protected]>
>
> Add device tree binding documentation for MARVELL's bluetooth sdio
> (sd8897 and sd8997) chip.
>
> Signed-off-by: Xinming Hu <[email protected]>
> Signed-off-by: Amitkumar Karwar <[email protected]>
> ---
> Listing changelist for both 1/2 and 2/2 here
> v2: Fixed build error reported by kbuild test robot
> drivers/bluetooth/btmrvl_platform.c:141:22: error:
> 'btmrvl_plt_pm_ops' undeclared here (not in a function)
>
> v3: Add NULL check for 'btmrvl_plt_dev'
>
> v4: Moved the bindings file to bindings/net/
> Corrected the name of 'name' and 'compatible' properties(Rob Herring)
>
> v5: Comments for wlan patches were applicable here as well. Like all binding
> changes in single file, specifying node as a child of SDIO controller.
>
> v6: a)Use <chip>-bt order for compatible attribute(Rob Herring)
> b)Split wakeuppin-gap to wakeup-pin and wakeup-gap(Rob Herring)
> c)Use sdio function number for both the unit address and reg(Rob Herring)
>
> v7: a)Use suggested vendor name and generic node name(Rob Herring)
> v8: a)Nodes are renamed as per suggestions from Rob Herring
> btmrvl,* -> marvell,*
> "wakeup-gap-msec" -> "wakeup-gap-ms"
> ---
> Documentation/devicetree/bindings/btmrvl.txt | 29 -----------
> .../devicetree/bindings/net/marvell-bt-sd8xxx.txt | 56 ++++++++++++++++++++++
> 2 files changed, 56 insertions(+), 29 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/btmrvl.txt
> create mode 100644 Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt
Thanks for getting this old binding fixed.
Acked-by: Rob Herring <[email protected]>