This patchset adds initial support for the clocks controlled by
the RPM (Resource Power Manager) processor on Qualcomm platforms.
The RPM is a dedicated hardware engine for managing the shared
SoC resources in order to keep the lowest power profile. It
communicates with other hardware subsystems via shared memory
and accepts clock requests, aggregates the requests and turns
the clocks on/off or scales them on demand.
Until now the RPM clock controller was not supported and a hard-
coded fixed-rate clocks were registered in the drivers. Now we
are moving the on-board clocks to the DT (where they actually
belong). If the RPM clock controller is enabled we insert it
right after the DT clocks making it a parent of some GCC clocks.
Changes since v8 (https://lkml.org/lkml/2016/4/14/495)
* Rebase and switch to clk_hw APIs
* Drop registration of all xo/cxo/pxo clocks and replace patch 3
with another one, which always registers factor clocks. With
this approuch we avoid having a DT dependency.
Changes since v7 (https://lkml.org/lkml/2016/2/23/542)
* Add handoff support.
* Remove smd-rpm XO clocks until clk deferring is supported.
Changes since v6 (https://lkml.org/lkml/2015/12/15/279)
* Remove header files and exported ops.
* Add support for active only RPM clocks.
Changes since v5 (https://lkml.org/lkml/2015/12/3/376)
* Drop all DT patches as they are already picked.
* Fix dependencies in Kconfig.
* Minor changes.
Changes since v4 (https://lkml.org/lkml/2015/11/19/309)
* Re-organize code into two separate drivers:
- clk-smd-rpm for RPM over SMD based clocks like msm8916
- clk-rpm for RPM based clocks like apq8064
* Drop the patches that are already merged.
* Added the extra compatible string to docs and example.
Changes since v3 (https://lkml.org/lkml/2015/10/20/613)
* Drop some of the patches as now we handle both scenarios -
RPMCC enabled or disabled.
* Addressed more comments from Stephen. Thanks again!
Changes since v2 (https://lkml.org/lkml/2015/8/3/513)
* Addressed various comments from Stephen. Thanks!
* Added sleep sets support.
* Added a mutex in the RPM driver.
* Support both scenarios - RPMCC enabled or disabled.
* Make RPMCC more generic in order to support other SMD RPM
based platforms.
Changes since v1 (https://lkml.org/lkml/2015/7/9/257):
* Changed the driver name to clk-smd-rpm, also build it only
when it is needed - suggested by Srini and Bjorn.
* More detailed binding example.
* Minor changes.
Georgi Djakov (3):
clk: qcom: Add support for SMD-RPM Clocks
clk: qcom: Add support for RPM Clocks
clk: qcom: Always add factor clock for xo clocks
.../devicetree/bindings/clock/qcom,rpmcc.txt | 37 ++
drivers/clk/qcom/Kconfig | 29 ++
drivers/clk/qcom/Makefile | 2 +
drivers/clk/qcom/clk-rpm.c | 489 ++++++++++++++++++
drivers/clk/qcom/clk-smd-rpm.c | 571 +++++++++++++++++++++
drivers/clk/qcom/common.c | 15 +-
include/dt-bindings/clock/qcom,rpmcc.h | 69 +++
7 files changed, 1203 insertions(+), 9 deletions(-)
create mode 100644 Documentation/devicetree/bindings/clock/qcom,rpmcc.txt
create mode 100644 drivers/clk/qcom/clk-rpm.c
create mode 100644 drivers/clk/qcom/clk-smd-rpm.c
create mode 100644 include/dt-bindings/clock/qcom,rpmcc.h
This adds initial support for clocks controlled by the Resource
Power Manager (RPM) processor on some Qualcomm SoCs, which use
the qcom_smd_rpm driver to communicate with RPM.
Such platforms are msm8916, apq8084 and msm8974.
The RPM is a dedicated hardware engine for managing the shared
SoC resources in order to keep the lowest power profile. It
communicates with other hardware subsystems via shared memory
and accepts clock requests, aggregates the requests and turns
the clocks on/off or scales them on demand.
This driver is based on the codeaurora.org driver:
https://www.codeaurora.org/cgit/quic/la/kernel/msm-3.10/tree/drivers/clk/qcom/clock-rpm.c
Signed-off-by: Georgi Djakov <[email protected]>
---
.../devicetree/bindings/clock/qcom,rpmcc.txt | 36 ++
drivers/clk/qcom/Kconfig | 16 +
drivers/clk/qcom/Makefile | 1 +
drivers/clk/qcom/clk-smd-rpm.c | 571 +++++++++++++++++++++
include/dt-bindings/clock/qcom,rpmcc.h | 45 ++
5 files changed, 669 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/qcom,rpmcc.txt
create mode 100644 drivers/clk/qcom/clk-smd-rpm.c
create mode 100644 include/dt-bindings/clock/qcom,rpmcc.h
diff --git a/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt b/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt
new file mode 100644
index 000000000000..e3e13226d798
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt
@@ -0,0 +1,36 @@
+Qualcomm RPM Clock Controller Binding
+------------------------------------------------
+The RPM is a dedicated hardware engine for managing the shared
+SoC resources in order to keep the lowest power profile. It
+communicates with other hardware subsystems via shared memory
+and accepts clock requests, aggregates the requests and turns
+the clocks on/off or scales them on demand.
+
+Required properties :
+- compatible : shall contain only one of the following. The generic
+ compatible "qcom,rpmcc" should be also included.
+
+ "qcom,rpmcc-msm8916", "qcom,rpmcc"
+
+- #clock-cells : shall contain 1
+
+Example:
+ smd {
+ compatible = "qcom,smd";
+
+ rpm {
+ interrupts = <0 168 1>;
+ qcom,ipc = <&apcs 8 0>;
+ qcom,smd-edge = <15>;
+
+ rpm_requests {
+ compatible = "qcom,rpm-msm8916";
+ qcom,smd-channels = "rpm_requests";
+
+ rpmcc: clock-controller {
+ compatible = "qcom,rpmcc-msm8916", "qcom,rpmcc";
+ #clock-cells = <1>;
+ };
+ };
+ };
+ };
diff --git a/drivers/clk/qcom/Kconfig b/drivers/clk/qcom/Kconfig
index 0146d3c2547f..b537c59dcfe6 100644
--- a/drivers/clk/qcom/Kconfig
+++ b/drivers/clk/qcom/Kconfig
@@ -2,6 +2,9 @@ config QCOM_GDSC
bool
select PM_GENERIC_DOMAINS if PM
+config QCOM_RPMCC
+ bool
+
config COMMON_CLK_QCOM
tristate "Support for Qualcomm's clock controllers"
depends on OF
@@ -9,6 +12,19 @@ config COMMON_CLK_QCOM
select REGMAP_MMIO
select RESET_CONTROLLER
+config QCOM_CLK_SMD_RPM
+ tristate "RPM over SMD based Clock Controller"
+ depends on COMMON_CLK_QCOM && QCOM_SMD_RPM
+ select QCOM_RPMCC
+ help
+ The RPM (Resource Power Manager) is a dedicated hardware engine for
+ managing the shared SoC resources in order to keep the lowest power
+ profile. It communicates with other hardware subsystems via shared
+ memory and accepts clock requests, aggregates the requests and turns
+ the clocks on/off or scales them on demand.
+ Say Y if you want to support the clocks exposed by the RPM on
+ platforms such as apq8016, apq8084, msm8974 etc.
+
config APQ_GCC_8084
tristate "APQ8084 Global Clock Controller"
select QCOM_GDSC
diff --git a/drivers/clk/qcom/Makefile b/drivers/clk/qcom/Makefile
index 1fb1f5476cb0..0dd72e56b7e4 100644
--- a/drivers/clk/qcom/Makefile
+++ b/drivers/clk/qcom/Makefile
@@ -29,3 +29,4 @@ obj-$(CONFIG_MSM_LCC_8960) += lcc-msm8960.o
obj-$(CONFIG_MSM_MMCC_8960) += mmcc-msm8960.o
obj-$(CONFIG_MSM_MMCC_8974) += mmcc-msm8974.o
obj-$(CONFIG_MSM_MMCC_8996) += mmcc-msm8996.o
+obj-$(CONFIG_QCOM_CLK_SMD_RPM) += clk-smd-rpm.o
diff --git a/drivers/clk/qcom/clk-smd-rpm.c b/drivers/clk/qcom/clk-smd-rpm.c
new file mode 100644
index 000000000000..8aba9ab2ccfd
--- /dev/null
+++ b/drivers/clk/qcom/clk-smd-rpm.c
@@ -0,0 +1,571 @@
+/*
+ * Copyright (c) 2016, Linaro Limited
+ * Copyright (c) 2014, The Linux Foundation. All rights reserved.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/err.h>
+#include <linux/export.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/soc/qcom/smd-rpm.h>
+
+#include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/mfd/qcom-rpm.h>
+
+#define QCOM_RPM_KEY_SOFTWARE_ENABLE 0x6e657773
+#define QCOM_RPM_KEY_PIN_CTRL_CLK_BUFFER_ENABLE_KEY 0x62636370
+#define QCOM_RPM_SMD_KEY_RATE 0x007a484b
+#define QCOM_RPM_SMD_KEY_ENABLE 0x62616e45
+#define QCOM_RPM_SMD_KEY_STATE 0x54415453
+#define QCOM_RPM_SCALING_ENABLE_ID 0x2
+
+#define __DEFINE_CLK_SMD_RPM(_platform, _name, _active, type, r_id, stat_id, \
+ key) \
+ static struct clk_smd_rpm _platform##_##_active; \
+ static struct clk_smd_rpm _platform##_##_name = { \
+ .rpm_res_type = (type), \
+ .rpm_clk_id = (r_id), \
+ .rpm_status_id = (stat_id), \
+ .rpm_key = (key), \
+ .peer = &_platform##_##_active, \
+ .rate = INT_MAX, \
+ .hw.init = &(struct clk_init_data){ \
+ .ops = &clk_smd_rpm_ops, \
+ .name = #_name, \
+ .parent_names = (const char *[]){ "xo_board" }, \
+ .num_parents = 1, \
+ }, \
+ }; \
+ static struct clk_smd_rpm _platform##_##_active = { \
+ .rpm_res_type = (type), \
+ .rpm_clk_id = (r_id), \
+ .rpm_status_id = (stat_id), \
+ .active_only = true, \
+ .rpm_key = (key), \
+ .peer = &_platform##_##_name, \
+ .rate = INT_MAX, \
+ .hw.init = &(struct clk_init_data){ \
+ .ops = &clk_smd_rpm_ops, \
+ .name = #_active, \
+ .parent_names = (const char *[]){ "xo_board" }, \
+ .num_parents = 1, \
+ }, \
+ }
+
+#define __DEFINE_CLK_SMD_RPM_BRANCH(_platform, _name, _active, type, r_id, \
+ stat_id, r, key) \
+ static struct clk_smd_rpm _platform##_##_active; \
+ static struct clk_smd_rpm _platform##_##_name = { \
+ .rpm_res_type = (type), \
+ .rpm_clk_id = (r_id), \
+ .rpm_status_id = (stat_id), \
+ .rpm_key = (key), \
+ .branch = true, \
+ .peer = &_platform##_##_active, \
+ .rate = (r), \
+ .hw.init = &(struct clk_init_data){ \
+ .ops = &clk_smd_rpm_branch_ops, \
+ .name = #_name, \
+ .parent_names = (const char *[]){ "xo_board" }, \
+ .num_parents = 1, \
+ }, \
+ }; \
+ static struct clk_smd_rpm _platform##_##_active = { \
+ .rpm_res_type = (type), \
+ .rpm_clk_id = (r_id), \
+ .rpm_status_id = (stat_id), \
+ .active_only = true, \
+ .rpm_key = (key), \
+ .branch = true, \
+ .peer = &_platform##_##_name, \
+ .rate = (r), \
+ .hw.init = &(struct clk_init_data){ \
+ .ops = &clk_smd_rpm_branch_ops, \
+ .name = #_active, \
+ .parent_names = (const char *[]){ "xo_board" }, \
+ .num_parents = 1, \
+ }, \
+ }
+
+#define DEFINE_CLK_SMD_RPM(_platform, _name, _active, type, r_id) \
+ __DEFINE_CLK_SMD_RPM(_platform, _name, _active, type, r_id, \
+ 0, QCOM_RPM_SMD_KEY_RATE)
+
+#define DEFINE_CLK_SMD_RPM_BRANCH(_platform, _name, _active, type, r_id, r) \
+ __DEFINE_CLK_SMD_RPM_BRANCH(_platform, _name, _active, type, \
+ r_id, 0, r, QCOM_RPM_SMD_KEY_ENABLE)
+
+#define DEFINE_CLK_SMD_RPM_QDSS(_platform, _name, _active, type, r_id) \
+ __DEFINE_CLK_SMD_RPM(_platform, _name, _active, type, r_id, \
+ 0, QCOM_RPM_SMD_KEY_STATE)
+
+#define DEFINE_CLK_SMD_RPM_XO_BUFFER(_platform, _name, _active, r_id) \
+ __DEFINE_CLK_SMD_RPM_BRANCH(_platform, _name, _active, \
+ QCOM_SMD_RPM_CLK_BUF_A, r_id, 0, 1000, \
+ QCOM_RPM_KEY_SOFTWARE_ENABLE)
+
+#define DEFINE_CLK_SMD_RPM_XO_BUFFER_PINCTRL(_platform, _name, _active, r_id) \
+ __DEFINE_CLK_SMD_RPM_BRANCH(_platform, _name, _active, \
+ QCOM_SMD_RPM_CLK_BUF_A, r_id, 0, 1000, \
+ QCOM_RPM_KEY_PIN_CTRL_CLK_BUFFER_ENABLE_KEY)
+
+#define to_clk_smd_rpm(_hw) container_of(_hw, struct clk_smd_rpm, hw)
+
+struct clk_smd_rpm {
+ const int rpm_res_type;
+ const int rpm_key;
+ const int rpm_clk_id;
+ const int rpm_status_id;
+ const bool active_only;
+ bool enabled;
+ bool branch;
+ struct clk_smd_rpm *peer;
+ struct clk_hw hw;
+ unsigned long rate;
+ struct qcom_smd_rpm *rpm;
+};
+
+struct clk_smd_rpm_req {
+ __le32 key;
+ __le32 nbytes;
+ __le32 value;
+};
+
+struct rpm_cc {
+ struct qcom_rpm *rpm;
+ struct clk_hw_onecell_data data;
+ struct clk_hw *hws[];
+};
+
+struct rpm_smd_clk_desc {
+ struct clk_smd_rpm **clks;
+ size_t num_clks;
+};
+
+static DEFINE_MUTEX(rpm_smd_clk_lock);
+
+static int clk_smd_rpm_handoff(struct clk_smd_rpm *r)
+{
+ int ret;
+ struct clk_smd_rpm_req req = {
+ .key = cpu_to_le32(r->rpm_key),
+ .nbytes = cpu_to_le32(sizeof(u32)),
+ .value = cpu_to_le32(INT_MAX),
+ };
+
+ ret = qcom_rpm_smd_write(r->rpm, QCOM_SMD_RPM_ACTIVE_STATE,
+ r->rpm_res_type, r->rpm_clk_id, &req,
+ sizeof(req));
+ if (ret)
+ return ret;
+ ret = qcom_rpm_smd_write(r->rpm, QCOM_SMD_RPM_SLEEP_STATE,
+ r->rpm_res_type, r->rpm_clk_id, &req,
+ sizeof(req));
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int clk_smd_rpm_set_rate_active(struct clk_smd_rpm *r,
+ unsigned long rate)
+{
+ struct clk_smd_rpm_req req = {
+ .key = cpu_to_le32(r->rpm_key),
+ .nbytes = cpu_to_le32(sizeof(u32)),
+ .value = cpu_to_le32(DIV_ROUND_UP(rate, 1000)), /* to kHz */
+ };
+
+ return qcom_rpm_smd_write(r->rpm, QCOM_SMD_RPM_ACTIVE_STATE,
+ r->rpm_res_type, r->rpm_clk_id, &req,
+ sizeof(req));
+}
+
+static int clk_smd_rpm_set_rate_sleep(struct clk_smd_rpm *r,
+ unsigned long rate)
+{
+ struct clk_smd_rpm_req req = {
+ .key = cpu_to_le32(r->rpm_key),
+ .nbytes = cpu_to_le32(sizeof(u32)),
+ .value = cpu_to_le32(DIV_ROUND_UP(rate, 1000)), /* to kHz */
+ };
+
+ return qcom_rpm_smd_write(r->rpm, QCOM_SMD_RPM_SLEEP_STATE,
+ r->rpm_res_type, r->rpm_clk_id, &req,
+ sizeof(req));
+}
+
+static void to_active_sleep(struct clk_smd_rpm *r, unsigned long rate,
+ unsigned long *active, unsigned long *sleep)
+{
+ *active = rate;
+
+ /*
+ * Active-only clocks don't care what the rate is during sleep. So,
+ * they vote for zero.
+ */
+ if (r->active_only)
+ *sleep = 0;
+ else
+ *sleep = *active;
+}
+
+static int clk_smd_rpm_prepare(struct clk_hw *hw)
+{
+ struct clk_smd_rpm *r = to_clk_smd_rpm(hw);
+ struct clk_smd_rpm *peer = r->peer;
+ unsigned long this_rate = 0, this_sleep_rate = 0;
+ unsigned long peer_rate = 0, peer_sleep_rate = 0;
+ unsigned long active_rate, sleep_rate;
+ int ret = 0;
+
+ mutex_lock(&rpm_smd_clk_lock);
+
+ /* Don't send requests to the RPM if the rate has not been set. */
+ if (!r->rate)
+ goto out;
+
+ to_active_sleep(r, r->rate, &this_rate, &this_sleep_rate);
+
+ /* Take peer clock's rate into account only if it's enabled. */
+ if (peer->enabled)
+ to_active_sleep(peer, peer->rate,
+ &peer_rate, &peer_sleep_rate);
+
+ active_rate = max(this_rate, peer_rate);
+
+ if (r->branch)
+ active_rate = !!active_rate;
+
+ ret = clk_smd_rpm_set_rate_active(r, active_rate);
+ if (ret)
+ goto out;
+
+ sleep_rate = max(this_sleep_rate, peer_sleep_rate);
+ if (r->branch)
+ sleep_rate = !!sleep_rate;
+
+ ret = clk_smd_rpm_set_rate_sleep(r, sleep_rate);
+ if (ret)
+ /* Undo the active set vote and restore it */
+ ret = clk_smd_rpm_set_rate_active(r, peer_rate);
+
+out:
+ if (!ret)
+ r->enabled = true;
+
+ mutex_unlock(&rpm_smd_clk_lock);
+
+ return ret;
+}
+
+static void clk_smd_rpm_unprepare(struct clk_hw *hw)
+{
+ struct clk_smd_rpm *r = to_clk_smd_rpm(hw);
+ struct clk_smd_rpm *peer = r->peer;
+ unsigned long peer_rate = 0, peer_sleep_rate = 0;
+ unsigned long active_rate, sleep_rate;
+ int ret;
+
+ mutex_lock(&rpm_smd_clk_lock);
+
+ if (!r->rate)
+ goto out;
+
+ /* Take peer clock's rate into account only if it's enabled. */
+ if (peer->enabled)
+ to_active_sleep(peer, peer->rate, &peer_rate,
+ &peer_sleep_rate);
+
+ active_rate = r->branch ? !!peer_rate : peer_rate;
+ ret = clk_smd_rpm_set_rate_active(r, active_rate);
+ if (ret)
+ goto out;
+
+ sleep_rate = r->branch ? !!peer_sleep_rate : peer_sleep_rate;
+ ret = clk_smd_rpm_set_rate_sleep(r, sleep_rate);
+ if (ret)
+ goto out;
+
+ r->enabled = false;
+
+out:
+ mutex_unlock(&rpm_smd_clk_lock);
+}
+
+static int clk_smd_rpm_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate)
+{
+ struct clk_smd_rpm *r = to_clk_smd_rpm(hw);
+ struct clk_smd_rpm *peer = r->peer;
+ unsigned long active_rate, sleep_rate;
+ unsigned long this_rate = 0, this_sleep_rate = 0;
+ unsigned long peer_rate = 0, peer_sleep_rate = 0;
+ int ret = 0;
+
+ mutex_lock(&rpm_smd_clk_lock);
+
+ if (!r->enabled)
+ goto out;
+
+ to_active_sleep(r, rate, &this_rate, &this_sleep_rate);
+
+ /* Take peer clock's rate into account only if it's enabled. */
+ if (peer->enabled)
+ to_active_sleep(peer, peer->rate,
+ &peer_rate, &peer_sleep_rate);
+
+ active_rate = max(this_rate, peer_rate);
+ ret = clk_smd_rpm_set_rate_active(r, active_rate);
+ if (ret)
+ goto out;
+
+ sleep_rate = max(this_sleep_rate, peer_sleep_rate);
+ ret = clk_smd_rpm_set_rate_sleep(r, sleep_rate);
+ if (ret)
+ goto out;
+
+ r->rate = rate;
+
+out:
+ mutex_unlock(&rpm_smd_clk_lock);
+
+ return ret;
+}
+
+static long clk_smd_rpm_round_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long *parent_rate)
+{
+ /*
+ * RPM handles rate rounding and we don't have a way to
+ * know what the rate will be, so just return whatever
+ * rate is requested.
+ */
+ return rate;
+}
+
+static unsigned long clk_smd_rpm_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ struct clk_smd_rpm *r = to_clk_smd_rpm(hw);
+
+ /*
+ * RPM handles rate rounding and we don't have a way to
+ * know what the rate will be, so just return whatever
+ * rate was set.
+ */
+ return r->rate;
+}
+
+static int clk_smd_rpm_enable_scaling(struct qcom_smd_rpm *rpm)
+{
+ int ret;
+ struct clk_smd_rpm_req req = {
+ .key = cpu_to_le32(QCOM_RPM_SMD_KEY_ENABLE),
+ .nbytes = cpu_to_le32(sizeof(u32)),
+ .value = cpu_to_le32(1),
+ };
+
+ ret = qcom_rpm_smd_write(rpm, QCOM_SMD_RPM_SLEEP_STATE,
+ QCOM_SMD_RPM_MISC_CLK,
+ QCOM_RPM_SCALING_ENABLE_ID, &req, sizeof(req));
+ if (ret) {
+ pr_err("RPM clock scaling (sleep set) not enabled!\n");
+ return ret;
+ }
+
+ ret = qcom_rpm_smd_write(rpm, QCOM_SMD_RPM_ACTIVE_STATE,
+ QCOM_SMD_RPM_MISC_CLK,
+ QCOM_RPM_SCALING_ENABLE_ID, &req, sizeof(req));
+ if (ret) {
+ pr_err("RPM clock scaling (active set) not enabled!\n");
+ return ret;
+ }
+
+ pr_debug("%s: RPM clock scaling is enabled\n", __func__);
+ return 0;
+}
+
+static const struct clk_ops clk_smd_rpm_ops = {
+ .prepare = clk_smd_rpm_prepare,
+ .unprepare = clk_smd_rpm_unprepare,
+ .set_rate = clk_smd_rpm_set_rate,
+ .round_rate = clk_smd_rpm_round_rate,
+ .recalc_rate = clk_smd_rpm_recalc_rate,
+};
+
+static const struct clk_ops clk_smd_rpm_branch_ops = {
+ .prepare = clk_smd_rpm_prepare,
+ .unprepare = clk_smd_rpm_unprepare,
+ .round_rate = clk_smd_rpm_round_rate,
+ .recalc_rate = clk_smd_rpm_recalc_rate,
+};
+
+/* msm8916 */
+DEFINE_CLK_SMD_RPM(msm8916, pcnoc_clk, pcnoc_a_clk, QCOM_SMD_RPM_BUS_CLK, 0);
+DEFINE_CLK_SMD_RPM(msm8916, snoc_clk, snoc_a_clk, QCOM_SMD_RPM_BUS_CLK, 1);
+DEFINE_CLK_SMD_RPM(msm8916, bimc_clk, bimc_a_clk, QCOM_SMD_RPM_MEM_CLK, 0);
+DEFINE_CLK_SMD_RPM_QDSS(msm8916, qdss_clk, qdss_a_clk, QCOM_SMD_RPM_MISC_CLK, 1);
+DEFINE_CLK_SMD_RPM_XO_BUFFER(msm8916, bb_clk1, bb_clk1_a, 1);
+DEFINE_CLK_SMD_RPM_XO_BUFFER(msm8916, bb_clk2, bb_clk2_a, 2);
+DEFINE_CLK_SMD_RPM_XO_BUFFER(msm8916, rf_clk1, rf_clk1_a, 4);
+DEFINE_CLK_SMD_RPM_XO_BUFFER(msm8916, rf_clk2, rf_clk2_a, 5);
+DEFINE_CLK_SMD_RPM_XO_BUFFER_PINCTRL(msm8916, bb_clk1_pin, bb_clk1_a_pin, 1);
+DEFINE_CLK_SMD_RPM_XO_BUFFER_PINCTRL(msm8916, bb_clk2_pin, bb_clk2_a_pin, 2);
+DEFINE_CLK_SMD_RPM_XO_BUFFER_PINCTRL(msm8916, rf_clk1_pin, rf_clk1_a_pin, 4);
+DEFINE_CLK_SMD_RPM_XO_BUFFER_PINCTRL(msm8916, rf_clk2_pin, rf_clk2_a_pin, 5);
+
+static struct clk_smd_rpm *msm8916_clks[] = {
+ [RPM_SMD_PCNOC_CLK] = &msm8916_pcnoc_clk,
+ [RPM_SMD_PCNOC_A_CLK] = &msm8916_pcnoc_a_clk,
+ [RPM_SMD_SNOC_CLK] = &msm8916_snoc_clk,
+ [RPM_SMD_SNOC_A_CLK] = &msm8916_snoc_a_clk,
+ [RPM_SMD_BIMC_CLK] = &msm8916_bimc_clk,
+ [RPM_SMD_BIMC_A_CLK] = &msm8916_bimc_a_clk,
+ [RPM_SMD_QDSS_CLK] = &msm8916_qdss_clk,
+ [RPM_SMD_QDSS_A_CLK] = &msm8916_qdss_a_clk,
+ [RPM_SMD_BB_CLK1] = &msm8916_bb_clk1,
+ [RPM_SMD_BB_CLK1_A] = &msm8916_bb_clk1_a,
+ [RPM_SMD_BB_CLK2] = &msm8916_bb_clk2,
+ [RPM_SMD_BB_CLK2_A] = &msm8916_bb_clk2_a,
+ [RPM_SMD_RF_CLK1] = &msm8916_rf_clk1,
+ [RPM_SMD_RF_CLK1_A] = &msm8916_rf_clk1_a,
+ [RPM_SMD_RF_CLK2] = &msm8916_rf_clk2,
+ [RPM_SMD_RF_CLK2_A] = &msm8916_rf_clk2_a,
+ [RPM_SMD_BB_CLK1_PIN] = &msm8916_bb_clk1_pin,
+ [RPM_SMD_BB_CLK1_A_PIN] = &msm8916_bb_clk1_a_pin,
+ [RPM_SMD_BB_CLK2_PIN] = &msm8916_bb_clk2_pin,
+ [RPM_SMD_BB_CLK2_A_PIN] = &msm8916_bb_clk2_a_pin,
+ [RPM_SMD_RF_CLK1_PIN] = &msm8916_rf_clk1_pin,
+ [RPM_SMD_RF_CLK1_A_PIN] = &msm8916_rf_clk1_a_pin,
+ [RPM_SMD_RF_CLK2_PIN] = &msm8916_rf_clk2_pin,
+ [RPM_SMD_RF_CLK2_A_PIN] = &msm8916_rf_clk2_a_pin,
+};
+
+static const struct rpm_smd_clk_desc rpm_clk_msm8916 = {
+ .clks = msm8916_clks,
+ .num_clks = ARRAY_SIZE(msm8916_clks),
+};
+
+static const struct of_device_id rpm_smd_clk_match_table[] = {
+ { .compatible = "qcom,rpmcc-msm8916", .data = &rpm_clk_msm8916 },
+ { }
+};
+MODULE_DEVICE_TABLE(of, rpm_smd_clk_match_table);
+
+static int rpm_smd_clk_probe(struct platform_device *pdev)
+{
+ struct clk_hw **hws;
+ struct rpm_cc *rcc;
+ struct clk_hw_onecell_data *data;
+ int ret;
+ size_t num_clks, i;
+ struct qcom_smd_rpm *rpm;
+ struct clk_smd_rpm **rpm_smd_clks;
+ const struct rpm_smd_clk_desc *desc;
+
+ rpm = dev_get_drvdata(pdev->dev.parent);
+ if (!rpm) {
+ dev_err(&pdev->dev, "Unable to retrieve handle to RPM\n");
+ return -ENODEV;
+ }
+
+ desc = of_device_get_match_data(&pdev->dev);
+ if (!desc)
+ return -EINVAL;
+
+ rpm_smd_clks = desc->clks;
+ num_clks = desc->num_clks;
+
+ rcc = devm_kzalloc(&pdev->dev, sizeof(*rcc) + sizeof(*hws) * num_clks,
+ GFP_KERNEL);
+ if (!rcc)
+ return -ENOMEM;
+
+ hws = rcc->hws;
+ data = &rcc->data;
+ data->num = num_clks;
+
+ for (i = 0; i < num_clks; i++) {
+ if (!rpm_smd_clks[i]) {
+ continue;
+ }
+
+ rpm_smd_clks[i]->rpm = rpm;
+
+ ret = clk_smd_rpm_handoff(rpm_smd_clks[i]);
+ if (ret)
+ goto err;
+ }
+
+ ret = clk_smd_rpm_enable_scaling(rpm);
+ if (ret)
+ goto err;
+
+ for (i = 0; i < num_clks; i++) {
+ if (!rpm_smd_clks[i]) {
+ data->hws[i] = ERR_PTR(-ENOENT);
+ continue;
+ }
+
+ ret = devm_clk_hw_register(&pdev->dev, &rpm_smd_clks[i]->hw);
+ if (ret)
+ goto err;
+ }
+
+ ret = of_clk_add_hw_provider(pdev->dev.of_node, of_clk_hw_onecell_get,
+ data);
+ if (ret)
+ goto err;
+
+ return 0;
+err:
+ dev_err(&pdev->dev, "Error registering SMD clock driver (%d)\n", ret);
+ return ret;
+}
+
+static int rpm_smd_clk_remove(struct platform_device *pdev)
+{
+ of_clk_del_provider(pdev->dev.of_node);
+ return 0;
+}
+
+static struct platform_driver rpm_smd_clk_driver = {
+ .driver = {
+ .name = "qcom-clk-smd-rpm",
+ .of_match_table = rpm_smd_clk_match_table,
+ },
+ .probe = rpm_smd_clk_probe,
+ .remove = rpm_smd_clk_remove,
+};
+
+static int __init rpm_smd_clk_init(void)
+{
+ return platform_driver_register(&rpm_smd_clk_driver);
+}
+core_initcall(rpm_smd_clk_init);
+
+static void __exit rpm_smd_clk_exit(void)
+{
+ platform_driver_unregister(&rpm_smd_clk_driver);
+}
+module_exit(rpm_smd_clk_exit);
+
+MODULE_DESCRIPTION("Qualcomm RPM over SMD Clock Controller Driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:qcom-clk-smd-rpm");
diff --git a/include/dt-bindings/clock/qcom,rpmcc.h b/include/dt-bindings/clock/qcom,rpmcc.h
new file mode 100644
index 000000000000..9fae52dfe35a
--- /dev/null
+++ b/include/dt-bindings/clock/qcom,rpmcc.h
@@ -0,0 +1,45 @@
+/*
+ * Copyright 2015 Linaro Limited
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _DT_BINDINGS_CLK_MSM_RPMCC_H
+#define _DT_BINDINGS_CLK_MSM_RPMCC_H
+
+/* msm8916 */
+#define RPM_SMD_XO_CLK_SRC 0
+#define RPM_SMD_XO_A_CLK_SRC 1
+#define RPM_SMD_PCNOC_CLK 2
+#define RPM_SMD_PCNOC_A_CLK 3
+#define RPM_SMD_SNOC_CLK 4
+#define RPM_SMD_SNOC_A_CLK 5
+#define RPM_SMD_BIMC_CLK 6
+#define RPM_SMD_BIMC_A_CLK 7
+#define RPM_SMD_QDSS_CLK 8
+#define RPM_SMD_QDSS_A_CLK 9
+#define RPM_SMD_BB_CLK1 10
+#define RPM_SMD_BB_CLK1_A 11
+#define RPM_SMD_BB_CLK2 12
+#define RPM_SMD_BB_CLK2_A 13
+#define RPM_SMD_RF_CLK1 14
+#define RPM_SMD_RF_CLK1_A 15
+#define RPM_SMD_RF_CLK2 16
+#define RPM_SMD_RF_CLK2_A 17
+#define RPM_SMD_BB_CLK1_PIN 18
+#define RPM_SMD_BB_CLK1_A_PIN 19
+#define RPM_SMD_BB_CLK2_PIN 20
+#define RPM_SMD_BB_CLK2_A_PIN 21
+#define RPM_SMD_RF_CLK1_PIN 22
+#define RPM_SMD_RF_CLK1_A_PIN 23
+#define RPM_SMD_RF_CLK2_PIN 24
+#define RPM_SMD_RF_CLK2_A_PIN 25
+
+#endif
Currently the RPM/RPM-SMD clock drivers do not register the xo clocks,
so we should always add factor clock. When we later add xo clocks support
into the drivers, we should update this function to skip registration.
By doing so we avoid any DT dependencies.
Signed-off-by: Georgi Djakov <[email protected]>
---
drivers/clk/qcom/common.c | 15 ++++++---------
1 file changed, 6 insertions(+), 9 deletions(-)
diff --git a/drivers/clk/qcom/common.c b/drivers/clk/qcom/common.c
index fffcbaf0fba7..27566a0098ca 100644
--- a/drivers/clk/qcom/common.c
+++ b/drivers/clk/qcom/common.c
@@ -153,15 +153,12 @@ int qcom_cc_register_board_clk(struct device *dev, const char *path,
const char *name, unsigned long rate)
{
bool add_factor = true;
- struct device_node *node;
-
- /* The RPM clock driver will add the factor clock if present */
- if (IS_ENABLED(CONFIG_QCOM_RPMCC)) {
- node = of_find_compatible_node(NULL, NULL, "qcom,rpmcc");
- if (of_device_is_available(node))
- add_factor = false;
- of_node_put(node);
- }
+
+ /*
+ * TODO: The RPM clock driver currently does not support the xo clock.
+ * When xo is added to the RPM clock driver, we should change this
+ * function to skip registration of xo factor clocks.
+ */
return _qcom_cc_register_board_clk(dev, path, name, rate, add_factor);
}
This adds initial support for clocks controlled by the Resource
Power Manager (RPM) processor on some Qualcomm SoCs, which use
the qcom_rpm driver to communicate with RPM.
Such platforms are apq8064 and msm8960.
Signed-off-by: Georgi Djakov <[email protected]>
---
.../devicetree/bindings/clock/qcom,rpmcc.txt | 1 +
drivers/clk/qcom/Kconfig | 13 +
drivers/clk/qcom/Makefile | 1 +
drivers/clk/qcom/clk-rpm.c | 489 +++++++++++++++++++++
include/dt-bindings/clock/qcom,rpmcc.h | 24 +
5 files changed, 528 insertions(+)
create mode 100644 drivers/clk/qcom/clk-rpm.c
diff --git a/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt b/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt
index e3e13226d798..87d3714b956a 100644
--- a/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt
+++ b/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt
@@ -11,6 +11,7 @@ Required properties :
compatible "qcom,rpmcc" should be also included.
"qcom,rpmcc-msm8916", "qcom,rpmcc"
+ "qcom,rpmcc-apq8064", "qcom,rpmcc"
- #clock-cells : shall contain 1
diff --git a/drivers/clk/qcom/Kconfig b/drivers/clk/qcom/Kconfig
index b537c59dcfe6..b82d2f33c9e4 100644
--- a/drivers/clk/qcom/Kconfig
+++ b/drivers/clk/qcom/Kconfig
@@ -12,6 +12,19 @@ config COMMON_CLK_QCOM
select REGMAP_MMIO
select RESET_CONTROLLER
+config QCOM_CLK_RPM
+ tristate "RPM based Clock Controller"
+ depends on COMMON_CLK_QCOM && MFD_QCOM_RPM
+ select QCOM_RPMCC
+ help
+ The RPM (Resource Power Manager) is a dedicated hardware engine for
+ managing the shared SoC resources in order to keep the lowest power
+ profile. It communicates with other hardware subsystems via shared
+ memory and accepts clock requests, aggregates the requests and turns
+ the clocks on/off or scales them on demand.
+ Say Y if you want to support the clocks exposed by the RPM on
+ platforms such as apq8064, msm8660, msm8960 etc.
+
config QCOM_CLK_SMD_RPM
tristate "RPM over SMD based Clock Controller"
depends on COMMON_CLK_QCOM && QCOM_SMD_RPM
diff --git a/drivers/clk/qcom/Makefile b/drivers/clk/qcom/Makefile
index 0dd72e56b7e4..eb2dfb32d960 100644
--- a/drivers/clk/qcom/Makefile
+++ b/drivers/clk/qcom/Makefile
@@ -29,4 +29,5 @@ obj-$(CONFIG_MSM_LCC_8960) += lcc-msm8960.o
obj-$(CONFIG_MSM_MMCC_8960) += mmcc-msm8960.o
obj-$(CONFIG_MSM_MMCC_8974) += mmcc-msm8974.o
obj-$(CONFIG_MSM_MMCC_8996) += mmcc-msm8996.o
+obj-$(CONFIG_QCOM_CLK_RPM) += clk-rpm.o
obj-$(CONFIG_QCOM_CLK_SMD_RPM) += clk-smd-rpm.o
diff --git a/drivers/clk/qcom/clk-rpm.c b/drivers/clk/qcom/clk-rpm.c
new file mode 100644
index 000000000000..f9fe452f49d6
--- /dev/null
+++ b/drivers/clk/qcom/clk-rpm.c
@@ -0,0 +1,489 @@
+/*
+ * Copyright (c) 2016, Linaro Limited
+ * Copyright (c) 2014, The Linux Foundation. All rights reserved.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/err.h>
+#include <linux/export.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/mfd/qcom_rpm.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+
+#include <dt-bindings/mfd/qcom-rpm.h>
+#include <dt-bindings/clock/qcom,rpmcc.h>
+
+#define QCOM_RPM_MISC_CLK_TYPE 0x306b6c63
+#define QCOM_RPM_SCALING_ENABLE_ID 0x2
+
+#define DEFINE_CLK_RPM(_platform, _name, _active, r_id) \
+ static struct clk_rpm _platform##_##_active; \
+ static struct clk_rpm _platform##_##_name = { \
+ .rpm_clk_id = (r_id), \
+ .peer = &_platform##_##_active, \
+ .rate = INT_MAX, \
+ .hw.init = &(struct clk_init_data){ \
+ .ops = &clk_rpm_ops, \
+ .name = #_name, \
+ .parent_names = (const char *[]){ "pxo_board" }, \
+ .num_parents = 1, \
+ }, \
+ }; \
+ static struct clk_rpm _platform##_##_active = { \
+ .rpm_clk_id = (r_id), \
+ .peer = &_platform##_##_name, \
+ .active_only = true, \
+ .rate = INT_MAX, \
+ .hw.init = &(struct clk_init_data){ \
+ .ops = &clk_rpm_ops, \
+ .name = #_active, \
+ .parent_names = (const char *[]){ "pxo_board" }, \
+ .num_parents = 1, \
+ }, \
+ }
+
+#define DEFINE_CLK_RPM_PXO_BRANCH(_platform, _name, _active, r_id, r) \
+ static struct clk_rpm _platform##_##_active; \
+ static struct clk_rpm _platform##_##_name = { \
+ .rpm_clk_id = (r_id), \
+ .active_only = true, \
+ .peer = &_platform##_##_active, \
+ .rate = (r), \
+ .branch = true, \
+ .hw.init = &(struct clk_init_data){ \
+ .ops = &clk_rpm_branch_ops, \
+ .name = #_name, \
+ .parent_names = (const char *[]){ "pxo_board" }, \
+ .num_parents = 1, \
+ }, \
+ }; \
+ static struct clk_rpm _platform##_##_active = { \
+ .rpm_clk_id = (r_id), \
+ .peer = &_platform##_##_name, \
+ .rate = (r), \
+ .branch = true, \
+ .hw.init = &(struct clk_init_data){ \
+ .ops = &clk_rpm_branch_ops, \
+ .name = #_active, \
+ .parent_names = (const char *[]){ "pxo_board" }, \
+ .num_parents = 1, \
+ }, \
+ }
+
+#define DEFINE_CLK_RPM_CXO_BRANCH(_platform, _name, _active, r_id, r) \
+ static struct clk_rpm _platform##_##_active; \
+ static struct clk_rpm _platform##_##_name = { \
+ .rpm_clk_id = (r_id), \
+ .peer = &_platform##_##_active, \
+ .rate = (r), \
+ .branch = true, \
+ .hw.init = &(struct clk_init_data){ \
+ .ops = &clk_rpm_branch_ops, \
+ .name = #_name, \
+ .parent_names = (const char *[]){ "cxo_board" }, \
+ .num_parents = 1, \
+ }, \
+ }; \
+ static struct clk_rpm _platform##_##_active = { \
+ .rpm_clk_id = (r_id), \
+ .active_only = true, \
+ .peer = &_platform##_##_name, \
+ .rate = (r), \
+ .branch = true, \
+ .hw.init = &(struct clk_init_data){ \
+ .ops = &clk_rpm_branch_ops, \
+ .name = #_active, \
+ .parent_names = (const char *[]){ "cxo_board" }, \
+ .num_parents = 1, \
+ }, \
+ }
+
+#define to_clk_rpm(_hw) container_of(_hw, struct clk_rpm, hw)
+
+struct clk_rpm {
+ const int rpm_clk_id;
+ const bool active_only;
+ unsigned long rate;
+ bool enabled;
+ bool branch;
+ struct clk_rpm *peer;
+ struct clk_hw hw;
+ struct qcom_rpm *rpm;
+};
+
+struct rpm_cc {
+ struct qcom_rpm *rpm;
+ struct clk_hw_onecell_data data;
+ struct clk_hw *hws[];
+};
+
+struct rpm_clk_desc {
+ struct clk_rpm **clks;
+ size_t num_clks;
+};
+
+static DEFINE_MUTEX(rpm_clk_lock);
+
+static int clk_rpm_handoff(struct clk_rpm *r)
+{
+ int ret;
+ u32 value = INT_MAX;
+
+ ret = qcom_rpm_write(r->rpm, QCOM_RPM_ACTIVE_STATE,
+ r->rpm_clk_id, &value, 1);
+ if (ret)
+ return ret;
+ ret = qcom_rpm_write(r->rpm, QCOM_RPM_SLEEP_STATE,
+ r->rpm_clk_id, &value, 1);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int clk_rpm_set_rate_active(struct clk_rpm *r, unsigned long rate)
+{
+ u32 value = DIV_ROUND_UP(rate, 1000); /* to kHz */
+
+ return qcom_rpm_write(r->rpm, QCOM_RPM_ACTIVE_STATE,
+ r->rpm_clk_id, &value, 1);
+}
+
+static int clk_rpm_set_rate_sleep(struct clk_rpm *r, unsigned long rate)
+{
+ u32 value = DIV_ROUND_UP(rate, 1000); /* to kHz */
+
+ return qcom_rpm_write(r->rpm, QCOM_RPM_SLEEP_STATE,
+ r->rpm_clk_id, &value, 1);
+}
+
+static void to_active_sleep(struct clk_rpm *r, unsigned long rate,
+ unsigned long *active, unsigned long *sleep)
+{
+ *active = rate;
+
+ /*
+ * Active-only clocks don't care what the rate is during sleep. So,
+ * they vote for zero.
+ */
+ if (r->active_only)
+ *sleep = 0;
+ else
+ *sleep = *active;
+}
+
+static int clk_rpm_prepare(struct clk_hw *hw)
+{
+ struct clk_rpm *r = to_clk_rpm(hw);
+ struct clk_rpm *peer = r->peer;
+ unsigned long this_rate = 0, this_sleep_rate = 0;
+ unsigned long peer_rate = 0, peer_sleep_rate = 0;
+ unsigned long active_rate, sleep_rate;
+ int ret = 0;
+
+ mutex_lock(&rpm_clk_lock);
+
+ /* Don't send requests to the RPM if the rate has not been set. */
+ if (!r->rate)
+ goto out;
+
+ to_active_sleep(r, r->rate, &this_rate, &this_sleep_rate);
+
+ /* Take peer clock's rate into account only if it's enabled. */
+ if (peer->enabled)
+ to_active_sleep(peer, peer->rate,
+ &peer_rate, &peer_sleep_rate);
+
+ active_rate = max(this_rate, peer_rate);
+
+ if (r->branch)
+ active_rate = !!active_rate;
+
+ ret = clk_rpm_set_rate_active(r, active_rate);
+ if (ret)
+ goto out;
+
+ sleep_rate = max(this_sleep_rate, peer_sleep_rate);
+ if (r->branch)
+ sleep_rate = !!sleep_rate;
+
+ ret = clk_rpm_set_rate_sleep(r, sleep_rate);
+ if (ret)
+ /* Undo the active set vote and restore it */
+ ret = clk_rpm_set_rate_active(r, peer_rate);
+
+out:
+ if (!ret)
+ r->enabled = true;
+
+ mutex_unlock(&rpm_clk_lock);
+
+ return ret;
+}
+
+static void clk_rpm_unprepare(struct clk_hw *hw)
+{
+ struct clk_rpm *r = to_clk_rpm(hw);
+ struct clk_rpm *peer = r->peer;
+ unsigned long peer_rate = 0, peer_sleep_rate = 0;
+ unsigned long active_rate, sleep_rate;
+ int ret;
+
+ mutex_lock(&rpm_clk_lock);
+
+ if (!r->rate)
+ goto out;
+
+ /* Take peer clock's rate into account only if it's enabled. */
+ if (peer->enabled)
+ to_active_sleep(peer, peer->rate, &peer_rate,
+ &peer_sleep_rate);
+
+ active_rate = r->branch ? !!peer_rate : peer_rate;
+ ret = clk_rpm_set_rate_active(r, active_rate);
+ if (ret)
+ goto out;
+
+ sleep_rate = r->branch ? !!peer_sleep_rate : peer_sleep_rate;
+ ret = clk_rpm_set_rate_sleep(r, sleep_rate);
+ if (ret)
+ goto out;
+
+ r->enabled = false;
+
+out:
+ mutex_unlock(&rpm_clk_lock);
+}
+
+static int clk_rpm_set_rate(struct clk_hw *hw,
+ unsigned long rate, unsigned long parent_rate)
+{
+ struct clk_rpm *r = to_clk_rpm(hw);
+ struct clk_rpm *peer = r->peer;
+ unsigned long active_rate, sleep_rate;
+ unsigned long this_rate = 0, this_sleep_rate = 0;
+ unsigned long peer_rate = 0, peer_sleep_rate = 0;
+ int ret = 0;
+
+ mutex_lock(&rpm_clk_lock);
+
+ if (!r->enabled)
+ goto out;
+
+ to_active_sleep(r, rate, &this_rate, &this_sleep_rate);
+
+ /* Take peer clock's rate into account only if it's enabled. */
+ if (peer->enabled)
+ to_active_sleep(peer, peer->rate,
+ &peer_rate, &peer_sleep_rate);
+
+ active_rate = max(this_rate, peer_rate);
+ ret = clk_rpm_set_rate_active(r, active_rate);
+ if (ret)
+ goto out;
+
+ sleep_rate = max(this_sleep_rate, peer_sleep_rate);
+ ret = clk_rpm_set_rate_sleep(r, sleep_rate);
+ if (ret)
+ goto out;
+
+ r->rate = rate;
+
+out:
+ mutex_unlock(&rpm_clk_lock);
+
+ return ret;
+}
+
+static long clk_rpm_round_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long *parent_rate)
+{
+ /*
+ * RPM handles rate rounding and we don't have a way to
+ * know what the rate will be, so just return whatever
+ * rate is requested.
+ */
+ return rate;
+}
+
+static unsigned long clk_rpm_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ struct clk_rpm *r = to_clk_rpm(hw);
+
+ /*
+ * RPM handles rate rounding and we don't have a way to
+ * know what the rate will be, so just return whatever
+ * rate was set.
+ */
+ return r->rate;
+}
+
+static const struct clk_ops clk_rpm_ops = {
+ .prepare = clk_rpm_prepare,
+ .unprepare = clk_rpm_unprepare,
+ .set_rate = clk_rpm_set_rate,
+ .round_rate = clk_rpm_round_rate,
+ .recalc_rate = clk_rpm_recalc_rate,
+};
+
+static const struct clk_ops clk_rpm_branch_ops = {
+ .prepare = clk_rpm_prepare,
+ .unprepare = clk_rpm_unprepare,
+ .round_rate = clk_rpm_round_rate,
+ .recalc_rate = clk_rpm_recalc_rate,
+};
+
+/* apq8064 */
+DEFINE_CLK_RPM(apq8064, afab_clk, afab_a_clk, QCOM_RPM_APPS_FABRIC_CLK);
+DEFINE_CLK_RPM(apq8064, cfpb_clk, cfpb_a_clk, QCOM_RPM_CFPB_CLK);
+DEFINE_CLK_RPM(apq8064, daytona_clk, daytona_a_clk, QCOM_RPM_DAYTONA_FABRIC_CLK);
+DEFINE_CLK_RPM(apq8064, ebi1_clk, ebi1_a_clk, QCOM_RPM_EBI1_CLK);
+DEFINE_CLK_RPM(apq8064, mmfab_clk, mmfab_a_clk, QCOM_RPM_MM_FABRIC_CLK);
+DEFINE_CLK_RPM(apq8064, mmfpb_clk, mmfpb_a_clk, QCOM_RPM_MMFPB_CLK);
+DEFINE_CLK_RPM(apq8064, sfab_clk, sfab_a_clk, QCOM_RPM_SYS_FABRIC_CLK);
+DEFINE_CLK_RPM(apq8064, sfpb_clk, sfpb_a_clk, QCOM_RPM_SFPB_CLK);
+DEFINE_CLK_RPM(apq8064, qdss_clk, qdss_a_clk, QCOM_RPM_QDSS_CLK);
+
+static struct clk_rpm *apq8064_clks[] = {
+ [RPM_APPS_FABRIC_CLK] = &apq8064_afab_clk,
+ [RPM_APPS_FABRIC_A_CLK] = &apq8064_afab_a_clk,
+ [RPM_CFPB_CLK] = &apq8064_cfpb_clk,
+ [RPM_CFPB_A_CLK] = &apq8064_cfpb_a_clk,
+ [RPM_DAYTONA_FABRIC_CLK] = &apq8064_daytona_clk,
+ [RPM_DAYTONA_FABRIC_A_CLK] = &apq8064_daytona_a_clk,
+ [RPM_EBI1_CLK] = &apq8064_ebi1_clk,
+ [RPM_EBI1_A_CLK] = &apq8064_ebi1_a_clk,
+ [RPM_MM_FABRIC_CLK] = &apq8064_mmfab_clk,
+ [RPM_MM_FABRIC_A_CLK] = &apq8064_mmfab_a_clk,
+ [RPM_MMFPB_CLK] = &apq8064_mmfpb_clk,
+ [RPM_MMFPB_A_CLK] = &apq8064_mmfpb_a_clk,
+ [RPM_SYS_FABRIC_CLK] = &apq8064_sfab_clk,
+ [RPM_SYS_FABRIC_A_CLK] = &apq8064_sfab_a_clk,
+ [RPM_SFPB_CLK] = &apq8064_sfpb_clk,
+ [RPM_SFPB_A_CLK] = &apq8064_sfpb_a_clk,
+ [RPM_QDSS_CLK] = &apq8064_qdss_clk,
+ [RPM_QDSS_A_CLK] = &apq8064_qdss_a_clk,
+};
+
+static const struct rpm_clk_desc rpm_clk_apq8064 = {
+ .clks = apq8064_clks,
+ .num_clks = ARRAY_SIZE(apq8064_clks),
+};
+
+static const struct of_device_id rpm_clk_match_table[] = {
+ { .compatible = "qcom,rpmcc-apq8064", .data = &rpm_clk_apq8064 },
+ { }
+};
+MODULE_DEVICE_TABLE(of, rpm_clk_match_table);
+
+static int rpm_clk_probe(struct platform_device *pdev)
+{
+ struct clk_hw **hws;
+ struct rpm_cc *rcc;
+ struct clk_hw_onecell_data *data;
+ int ret;
+ size_t num_clks, i;
+ struct qcom_rpm *rpm;
+ struct clk_rpm **rpm_clks;
+ const struct rpm_clk_desc *desc;
+
+ rpm = dev_get_drvdata(pdev->dev.parent);
+ if (!rpm) {
+ dev_err(&pdev->dev, "Unable to retrieve handle to RPM\n");
+ return -ENODEV;
+ }
+
+ desc = of_device_get_match_data(&pdev->dev);
+ if (!desc)
+ return -EINVAL;
+
+ rpm_clks = desc->clks;
+ num_clks = desc->num_clks;
+
+ rcc = devm_kzalloc(&pdev->dev, sizeof(*rcc) + sizeof(*hws) * num_clks,
+ GFP_KERNEL);
+ if (!rcc)
+ return -ENOMEM;
+
+ hws = rcc->hws;
+ data = &rcc->data;
+ data->num = num_clks;
+
+ for (i = 0; i < num_clks; i++) {
+ if (!rpm_clks[i])
+ continue;
+
+ rpm_clks[i]->rpm = rpm;
+
+ ret = clk_rpm_handoff(rpm_clks[i]);
+ if (ret)
+ goto err;
+ }
+
+ for (i = 0; i < num_clks; i++) {
+ if (!rpm_clks[i]) {
+ data->hws[i] = ERR_PTR(-ENOENT);
+ continue;
+ }
+
+ ret = devm_clk_hw_register(&pdev->dev, &rpm_clks[i]->hw);
+ if (ret)
+ goto err;
+ }
+
+ ret = of_clk_add_hw_provider(pdev->dev.of_node, of_clk_hw_onecell_get,
+ data);
+ if (ret)
+ goto err;
+
+ return 0;
+err:
+ dev_err(&pdev->dev, "Error registering RPM Clock driver (%d)\n", ret);
+ return ret;
+}
+
+static int rpm_clk_remove(struct platform_device *pdev)
+{
+ of_clk_del_provider(pdev->dev.of_node);
+ return 0;
+}
+
+static struct platform_driver rpm_clk_driver = {
+ .driver = {
+ .name = "qcom-clk-rpm",
+ .of_match_table = rpm_clk_match_table,
+ },
+ .probe = rpm_clk_probe,
+ .remove = rpm_clk_remove,
+};
+
+static int __init rpm_clk_init(void)
+{
+ return platform_driver_register(&rpm_clk_driver);
+}
+core_initcall(rpm_clk_init);
+
+static void __exit rpm_clk_exit(void)
+{
+ platform_driver_unregister(&rpm_clk_driver);
+}
+module_exit(rpm_clk_exit);
+
+MODULE_DESCRIPTION("Qualcomm RPM Clock Controller Driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:qcom-clk-rpm");
diff --git a/include/dt-bindings/clock/qcom,rpmcc.h b/include/dt-bindings/clock/qcom,rpmcc.h
index 9fae52dfe35a..5924cdb71336 100644
--- a/include/dt-bindings/clock/qcom,rpmcc.h
+++ b/include/dt-bindings/clock/qcom,rpmcc.h
@@ -14,6 +14,30 @@
#ifndef _DT_BINDINGS_CLK_MSM_RPMCC_H
#define _DT_BINDINGS_CLK_MSM_RPMCC_H
+/* apq8064 */
+#define RPM_PXO_CLK 0
+#define RPM_PXO_A_CLK 1
+#define RPM_CXO_CLK 2
+#define RPM_CXO_A_CLK 3
+#define RPM_APPS_FABRIC_CLK 4
+#define RPM_APPS_FABRIC_A_CLK 5
+#define RPM_CFPB_CLK 6
+#define RPM_CFPB_A_CLK 7
+#define RPM_QDSS_CLK 8
+#define RPM_QDSS_A_CLK 9
+#define RPM_DAYTONA_FABRIC_CLK 10
+#define RPM_DAYTONA_FABRIC_A_CLK 11
+#define RPM_EBI1_CLK 12
+#define RPM_EBI1_A_CLK 13
+#define RPM_MM_FABRIC_CLK 14
+#define RPM_MM_FABRIC_A_CLK 15
+#define RPM_MMFPB_CLK 16
+#define RPM_MMFPB_A_CLK 17
+#define RPM_SYS_FABRIC_CLK 18
+#define RPM_SYS_FABRIC_A_CLK 19
+#define RPM_SFPB_CLK 20
+#define RPM_SFPB_A_CLK 21
+
/* msm8916 */
#define RPM_SMD_XO_CLK_SRC 0
#define RPM_SMD_XO_A_CLK_SRC 1
On Wed, Nov 02, 2016 at 05:56:57PM +0200, Georgi Djakov wrote:
> This adds initial support for clocks controlled by the Resource
> Power Manager (RPM) processor on some Qualcomm SoCs, which use
> the qcom_rpm driver to communicate with RPM.
> Such platforms are apq8064 and msm8960.
>
> Signed-off-by: Georgi Djakov <[email protected]>
> ---
> .../devicetree/bindings/clock/qcom,rpmcc.txt | 1 +
Acked-by: Rob Herring <[email protected]>
> drivers/clk/qcom/Kconfig | 13 +
> drivers/clk/qcom/Makefile | 1 +
> drivers/clk/qcom/clk-rpm.c | 489 +++++++++++++++++++++
> include/dt-bindings/clock/qcom,rpmcc.h | 24 +
> 5 files changed, 528 insertions(+)
> create mode 100644 drivers/clk/qcom/clk-rpm.c
On Wed, Nov 02, 2016 at 05:56:56PM +0200, Georgi Djakov wrote:
> This adds initial support for clocks controlled by the Resource
> Power Manager (RPM) processor on some Qualcomm SoCs, which use
> the qcom_smd_rpm driver to communicate with RPM.
> Such platforms are msm8916, apq8084 and msm8974.
>
> The RPM is a dedicated hardware engine for managing the shared
> SoC resources in order to keep the lowest power profile. It
> communicates with other hardware subsystems via shared memory
> and accepts clock requests, aggregates the requests and turns
> the clocks on/off or scales them on demand.
>
> This driver is based on the codeaurora.org driver:
> https://www.codeaurora.org/cgit/quic/la/kernel/msm-3.10/tree/drivers/clk/qcom/clock-rpm.c
>
> Signed-off-by: Georgi Djakov <[email protected]>
> ---
> .../devicetree/bindings/clock/qcom,rpmcc.txt | 36 ++
Acked-by: Rob Herring <[email protected]>
> drivers/clk/qcom/Kconfig | 16 +
> drivers/clk/qcom/Makefile | 1 +
> drivers/clk/qcom/clk-smd-rpm.c | 571 +++++++++++++++++++++
> include/dt-bindings/clock/qcom,rpmcc.h | 45 ++
> 5 files changed, 669 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/clock/qcom,rpmcc.txt
> create mode 100644 drivers/clk/qcom/clk-smd-rpm.c
> create mode 100644 include/dt-bindings/clock/qcom,rpmcc.h
On 11/02, Georgi Djakov wrote:
> Currently the RPM/RPM-SMD clock drivers do not register the xo clocks,
> so we should always add factor clock. When we later add xo clocks support
> into the drivers, we should update this function to skip registration.
> By doing so we avoid any DT dependencies.
>
> Signed-off-by: Georgi Djakov <[email protected]>
> ---
Applied to clk-qcom-rpm and merged into clk-next
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
On 11/02, Georgi Djakov wrote:
> This adds initial support for clocks controlled by the Resource
> Power Manager (RPM) processor on some Qualcomm SoCs, which use
> the qcom_rpm driver to communicate with RPM.
> Such platforms are apq8064 and msm8960.
>
> Signed-off-by: Georgi Djakov <[email protected]>
> ---
Applied to clk-qcom-rpm and merged into clk-next
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
On 11/02, Georgi Djakov wrote:
> This adds initial support for clocks controlled by the Resource
> Power Manager (RPM) processor on some Qualcomm SoCs, which use
> the qcom_smd_rpm driver to communicate with RPM.
> Such platforms are msm8916, apq8084 and msm8974.
>
> The RPM is a dedicated hardware engine for managing the shared
> SoC resources in order to keep the lowest power profile. It
> communicates with other hardware subsystems via shared memory
> and accepts clock requests, aggregates the requests and turns
> the clocks on/off or scales them on demand.
>
> This driver is based on the codeaurora.org driver:
> https://www.codeaurora.org/cgit/quic/la/kernel/msm-3.10/tree/drivers/clk/qcom/clock-rpm.c
>
> Signed-off-by: Georgi Djakov <[email protected]>
> ---
Applied to clk-qcom-rpm and merged into clk-next
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project