When a need raise up to use JTAG interface for system's devices
programming or CPU debugging, it could be done from the external
JTAG master controller.
For such purpose, usually the user layer
application implements jtag protocol or using a proprietary
connection to vendor hardware.
This method is slow and not generic.
We propose to implement general JTAG interface and infrastructure
to communicate with user layer application. In such way, we can
have the standard JTAG interface core part and separation from
specific HW implementation.
This allow new capability to debug the CPU or program system's
device via BMC without additional devices nor cost.
This patch purpose is to add JTAG master core infrastructure by
defining new JTAG class and provide generic JTAG interface
to allow hardware specific drivers to connect this interface.
This will enable all JTAG drivers to use the common interface
part and will have separate for hardware implementation.
The JTAG (Joint Test Action Group) core driver provides minimal generic
JTAG interface, which can be used by hardware specific JTAG master
controllers. By providing common interface for the JTAG controllers,
user space device programing is hardware independent.
Modern SoC which in use for embedded system' equipped with
internal JTAG master interface.
This interface is used for programming and debugging system's
hardware components, like CPLD, FPGA, CPU, voltage and
industrial controllers.
Firmware for such devices can be upgraded through JTAG interface during
Runtime. The JTAG standard support for multiple devices programming,
is in case their lines are daisy-chained together.
For example, systems which equipped with host CPU, BMC SoC or/and
number of programmable devices are capable to connect a pin and
select system components dynamically for programming and debugging,
This is using by the BMC which is equipped with internal SoC master
controller.
For example:
BMC JTAG master --> pin selected to CPLDs chain for programming (filed
upgrade, production)
BMC JTAG master --> pin selected to voltage monitors for programming
(field upgrade, production)
BMC JTAG master --> pin selected to host CPU (on-site debugging
and developers debugging)
For example, we can have application in user space which using calls
to JTAG driver executes CPLD programming directly from SVF file
The JTAG standard (IEEE 1149.1) defines the next connector pins:
- TDI (Test Data In);
- TDO (Test Data Out);
- TCK (Test Clock);
- TMS (Test Mode Select);
- TRST (Test Reset) (Optional);
The SoC equipped with JTAG master controller, performs
device programming on command or vector level. For example
a file in a standard SVF (Serial Vector Format) that contains
boundary scan vectors, can be used by sending each vector
to the JTAG interface and the JTAG controller will execute
the programming.
Initial version provides the system calls set for:
- SIR (Scan Instruction Register, IEEE 1149.1 Data Register scan);
- SDR (Scan Data Register, IEEE 1149.1 Instruction Register scan);
- RUNTEST (Forces the IEEE 1149.1 bus to a run state for a specified
number of clocks.
SoC which are not equipped with JTAG master interface, can be built
on top of JTAG core driver infrastructure, by applying bit-banging of
TDI, TDO, TCK and TMS pins within the hardware specific driver.
Oleksandr Shamray (2):
drivers: jtag: Add JTAG core driver
drivers: jtag: Add Aspeed SoC 24xx and 25xx families JTAG master
driver
.../devicetree/bindings/jtag/aspeed-jtag.txt | 27 +
Documentation/ioctl/ioctl-number.txt | 2 +
MAINTAINERS | 8 +
drivers/Kconfig | 2 +
drivers/Makefile | 1 +
drivers/jtag/Kconfig | 29 +
drivers/jtag/Makefile | 2 +
drivers/jtag/jtag-aspeed.c | 774 ++++++++++++++++++++
drivers/jtag/jtag.c | 313 ++++++++
include/linux/jtag.h | 42 ++
include/uapi/linux/jtag.h | 113 +++
11 files changed, 1313 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/jtag/aspeed-jtag.txt
create mode 100644 drivers/jtag/Kconfig
create mode 100644 drivers/jtag/Makefile
create mode 100644 drivers/jtag/jtag-aspeed.c
create mode 100644 drivers/jtag/jtag.c
create mode 100644 include/linux/jtag.h
create mode 100644 include/uapi/linux/jtag.h
Initial patch for JTAG friver
JTAG class driver provide infrastructure to support hardware/software
JTAG platform drivers. It provide user layer API interface for flashing
and debugging external devices which equipped with JTAG interface
using standard transactions.
Driver exposes set of IOCTL to user space for:
- XFER:
- SIR (Scan Instruction Register, IEEE 1149.1 Data Register scan);
- SDR (Scan Data Register, IEEE 1149.1 Instruction Register scan);
- RUNTEST (Forces the IEEE 1149.1 bus to a run state for a specified
number of clocks).
- SIOCFREQ/GIOCFREQ for setting and reading JTAG frequency.
Driver core provides set of internal APIs for allocation and
registration:
- jtag_register;
- jtag_unregister;
- jtag_alloc;
- jtag_free;
Platform driver on registration with jtag-core creates the next
entry in dev folder:
/dev/jtagX
Signed-off-by: Jiri Pirko <[email protected]>
Signed-off-by: Oleksandr Shamray <[email protected]>
---
v1->v2
Comments pointed by Greg KH <[email protected]>
- Change license type from GPLv2/BSD to GPLv2
- Change type of variables which crossed user/kernel to __type
- Remove "default n" from Kconfig
Comments pointed by Andrew Lunn <[email protected]>
- Change list_add_tail in jtag_unregister to list_del
Comments pointed by Neil Armstrong <[email protected]>
- Add SPDX-License-Identifier instead of license text
Comments pointed by Arnd Bergmann <[email protected]>
- Change __copy_to_user to memdup_user
- Change __put_user to put_user
- Change type of variables to __type for compatible 32 and 64-bit systems
- Add check for maximum xfer data size
- Change lookup data mechanism to get jtag data from inode
- Add .compat_ioctl to file ops
- Add mem alignment for jtag priv data
Comments pointed by Tobias Klauser <[email protected]>
- Change function names to avoid match with variable types
- Fix description for jtag_ru_test_idle in uapi jtag.h
- Fix misprints IDEL/IDLE, trough/through
---
Documentation/ioctl/ioctl-number.txt | 2 +
MAINTAINERS | 8 +
drivers/Kconfig | 2 +
drivers/Makefile | 1 +
drivers/jtag/Kconfig | 16 ++
drivers/jtag/Makefile | 1 +
drivers/jtag/jtag.c | 313 ++++++++++++++++++++++++++++++++++
include/linux/jtag.h | 42 +++++
include/uapi/linux/jtag.h | 113 ++++++++++++
9 files changed, 498 insertions(+), 0 deletions(-)
create mode 100644 drivers/jtag/Kconfig
create mode 100644 drivers/jtag/Makefile
create mode 100644 drivers/jtag/jtag.c
create mode 100644 include/linux/jtag.h
create mode 100644 include/uapi/linux/jtag.h
diff --git a/Documentation/ioctl/ioctl-number.txt b/Documentation/ioctl/ioctl-number.txt
index 3e3fdae..1af2508 100644
--- a/Documentation/ioctl/ioctl-number.txt
+++ b/Documentation/ioctl/ioctl-number.txt
@@ -321,6 +321,8 @@ Code Seq#(hex) Include File Comments
0xB0 all RATIO devices in development:
<mailto:[email protected]>
0xB1 00-1F PPPoX <mailto:[email protected]>
+0xB2 00-0f linux/jtag.h JTAG driver
+ <mailto:[email protected]>
0xB3 00 linux/mmc/ioctl.h
0xB4 00-0F linux/gpio.h <mailto:[email protected]>
0xB5 00-0F uapi/linux/rpmsg.h <mailto:[email protected]>
diff --git a/MAINTAINERS b/MAINTAINERS
index 205d397..141aeaf 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -7292,6 +7292,14 @@ L: [email protected]
S: Maintained
F: drivers/tty/serial/jsm/
+JTAG SUBSYSTEM
+M: Oleksandr Shamray <[email protected]>
+M: Vadim Pasternak <[email protected]>
+S: Maintained
+F: include/linux/jtag.h
+F: include/uapi/linux/jtag.h
+F: drivers/jtag/
+
K10TEMP HARDWARE MONITORING DRIVER
M: Clemens Ladisch <[email protected]>
L: [email protected]
diff --git a/drivers/Kconfig b/drivers/Kconfig
index 505c676..2214678 100644
--- a/drivers/Kconfig
+++ b/drivers/Kconfig
@@ -208,4 +208,6 @@ source "drivers/tee/Kconfig"
source "drivers/mux/Kconfig"
+source "drivers/jtag/Kconfig"
+
endmenu
diff --git a/drivers/Makefile b/drivers/Makefile
index dfdcda0..6a2059b 100644
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -182,3 +182,4 @@ obj-$(CONFIG_FPGA) += fpga/
obj-$(CONFIG_FSI) += fsi/
obj-$(CONFIG_TEE) += tee/
obj-$(CONFIG_MULTIPLEXER) += mux/
+obj-$(CONFIG_JTAG) += jtag/
diff --git a/drivers/jtag/Kconfig b/drivers/jtag/Kconfig
new file mode 100644
index 0000000..0fad1a3
--- /dev/null
+++ b/drivers/jtag/Kconfig
@@ -0,0 +1,16 @@
+menuconfig JTAG
+ tristate "JTAG support"
+ ---help---
+ This provides basic core functionality support for jtag class devices
+ Hardware equipped with JTAG microcontroller which can be built
+ on top of this drivers. Driver exposes the set of IOCTL to the
+ user space for:
+ SIR (Scan Instruction Register, IEEE 1149.1 Data Register scan);
+ SDR (Scan Data Register, IEEE 1149.1 Instruction Register scan);
+ RUNTEST (Forces IEEE 1149.1 bus to a run state for specified
+ number of clocks).
+
+ If you want this support, you should say Y here.
+
+ To compile this driver as a module, choose M here: the module will
+ be called jtag.
diff --git a/drivers/jtag/Makefile b/drivers/jtag/Makefile
new file mode 100644
index 0000000..af37493
--- /dev/null
+++ b/drivers/jtag/Makefile
@@ -0,0 +1 @@
+obj-$(CONFIG_JTAG) += jtag.o
diff --git a/drivers/jtag/jtag.c b/drivers/jtag/jtag.c
new file mode 100644
index 0000000..88adf64
--- /dev/null
+++ b/drivers/jtag/jtag.c
@@ -0,0 +1,313 @@
+/*
+ * drivers/jtag/jtag.c
+ *
+ * Copyright (c) 2017 Mellanox Technologies. All rights reserved.
+ * Copyright (c) 2017 Oleksandr Shamray <[email protected]>
+ *
+ * Released under the GPLv2 only.
+ * SPDX-License-Identifier: GPL-2.0
+ */
+
+#include <linux/cdev.h>
+#include <linux/device.h>
+#include <linux/jtag.h>
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/module.h>
+#include <linux/rtnetlink.h>
+#include <linux/spinlock.h>
+#include <uapi/linux/jtag.h>
+
+struct jtag {
+ struct list_head list;
+ struct device *dev;
+ struct cdev cdev;
+ int id;
+ spinlock_t lock;
+ bool is_open;
+ const struct jtag_ops *ops;
+ unsigned long priv[0] __aligned(ARCH_DMA_MINALIGN);
+};
+
+static dev_t jtag_devt;
+static LIST_HEAD(jtag_list);
+static DEFINE_MUTEX(jtag_mutex);
+static DEFINE_IDA(jtag_ida);
+
+void *jtag_priv(struct jtag *jtag)
+{
+ return jtag->priv;
+}
+EXPORT_SYMBOL_GPL(jtag_priv);
+
+static void *jtag_copy_from_user(void __user *udata, unsigned long bit_size)
+{
+ unsigned long size;
+ void *kdata;
+
+ size = DIV_ROUND_UP(bit_size, BITS_PER_BYTE);
+ kdata = memdup_user(udata, size);
+
+ return kdata;
+}
+
+static unsigned long jtag_copy_to_user(void __user *udata, void *kdata,
+ unsigned long bit_size)
+{
+ unsigned long size;
+
+ size = DIV_ROUND_UP(bit_size, BITS_PER_BYTE);
+ return copy_to_user(udata, kdata, size);
+}
+
+static struct class jtag_class = {
+ .name = "jtag",
+ .owner = THIS_MODULE,
+};
+
+static int jtag_run_test_idle_op(struct jtag *jtag,
+ struct jtag_run_test_idle *idle)
+{
+ if (jtag->ops->idle)
+ return jtag->ops->idle(jtag, idle);
+ else
+ return -EOPNOTSUPP;
+}
+
+static int jtag_xfer_op(struct jtag *jtag, struct jtag_xfer *xfer)
+{
+ if (jtag->ops->xfer)
+ return jtag->ops->xfer(jtag, xfer);
+ else
+ return -EOPNOTSUPP;
+}
+
+static long jtag_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
+{
+ struct jtag *jtag = file->private_data;
+ void *varg = (void __user *)arg;
+ __u32 *uarg = (__u32 __user *)arg;
+ struct jtag_run_test_idle idle;
+ struct jtag_xfer xfer;
+ void *user_tdio_data;
+ __u32 value;
+ int err;
+
+ switch (cmd) {
+ case JTAG_GIOCFREQ:
+ if (jtag->ops->freq_get)
+ err = jtag->ops->freq_get(jtag, &value);
+ else
+ err = -EOPNOTSUPP;
+ if (err)
+ break;
+
+ err = put_user(value, uarg);
+ break;
+
+ case JTAG_SIOCFREQ:
+ err = __get_user(value, uarg);
+
+ if (value == 0)
+ err = -EINVAL;
+ if (err)
+ break;
+
+ if (jtag->ops->freq_set)
+ err = jtag->ops->freq_set(jtag, value);
+ else
+ err = -EOPNOTSUPP;
+ break;
+
+ case JTAG_IOCRUNTEST:
+ if (copy_from_user(&idle, varg,
+ sizeof(struct jtag_run_test_idle)))
+ return -ENOMEM;
+ err = jtag_run_test_idle_op(jtag, &idle);
+ break;
+
+ case JTAG_IOCXFER:
+ if (copy_from_user(&xfer, varg, sizeof(struct jtag_xfer)))
+ return -EFAULT;
+
+ if (xfer.length >= JTAG_MAX_XFER_DATA_LEN)
+ return -EFAULT;
+
+ user_tdio_data = xfer.tdio;
+ xfer.tdio = jtag_copy_from_user((void __user *)user_tdio_data,
+ xfer.length);
+ if (!xfer.tdio)
+ return -ENOMEM;
+
+ err = jtag_xfer_op(jtag, &xfer);
+ if (jtag_copy_to_user((void __user *)user_tdio_data,
+ xfer.tdio, xfer.length)) {
+ kfree(xfer.tdio);
+ return -EFAULT;
+ }
+
+ kfree(xfer.tdio);
+ xfer.tdio = user_tdio_data;
+ if (copy_to_user(varg, &xfer, sizeof(struct jtag_xfer))) {
+ kfree(xfer.tdio);
+ return -EFAULT;
+ }
+ break;
+
+ case JTAG_GIOCSTATUS:
+ if (jtag->ops->status_get)
+ err = jtag->ops->status_get(jtag,
+ (enum jtag_endstate *)&value);
+ else
+ err = -EOPNOTSUPP;
+ if (err)
+ break;
+
+ err = put_user(value, uarg);
+ break;
+
+ default:
+ return -EINVAL;
+ }
+ return err;
+}
+
+#ifdef CONFIG_COMPAT
+static long jtag_ioctl_compat(struct file *file, unsigned int cmd,
+ unsigned long arg)
+{
+ return jtag_ioctl(file, cmd, (unsigned long)compat_ptr(arg));
+}
+#endif
+
+static int jtag_open(struct inode *inode, struct file *file)
+{
+ struct jtag *jtag = container_of(inode->i_cdev, struct jtag, cdev);
+
+ spin_lock(&jtag->lock);
+
+ if (jtag->is_open) {
+ dev_info(NULL, "jtag already opened\n");
+ spin_unlock(&jtag->lock);
+ return -EBUSY;
+ }
+
+ jtag->is_open = true;
+ file->private_data = jtag;
+ spin_unlock(&jtag->lock);
+ return 0;
+}
+
+static int jtag_release(struct inode *inode, struct file *file)
+{
+ struct jtag *jtag = file->private_data;
+
+ spin_lock(&jtag->lock);
+ jtag->is_open = false;
+ spin_unlock(&jtag->lock);
+ return 0;
+}
+
+static const struct file_operations jtag_fops = {
+ .owner = THIS_MODULE,
+ .open = jtag_open,
+ .release = jtag_release,
+ .llseek = noop_llseek,
+ .unlocked_ioctl = jtag_ioctl,
+#ifdef CONFIG_COMPAT
+ .compat_ioctl = jtag_ioctl_compat,
+#endif
+};
+
+struct jtag *jtag_alloc(size_t priv_size, const struct jtag_ops *ops)
+{
+ struct jtag *jtag;
+
+ jtag = kzalloc(sizeof(*jtag) + round_up(priv_size, ARCH_DMA_MINALIGN),
+ GFP_KERNEL);
+ if (!jtag)
+ return NULL;
+
+ jtag->ops = ops;
+ return jtag;
+}
+EXPORT_SYMBOL_GPL(jtag_alloc);
+
+void jtag_free(struct jtag *jtag)
+{
+ kfree(jtag);
+}
+EXPORT_SYMBOL_GPL(jtag_free);
+
+int jtag_register(struct jtag *jtag)
+{
+ int id;
+ int err;
+
+ id = ida_simple_get(&jtag_ida, 0, 0, GFP_KERNEL);
+ if (id < 0)
+ return id;
+
+ jtag->id = id;
+ cdev_init(&jtag->cdev, &jtag_fops);
+ jtag->cdev.owner = THIS_MODULE;
+ err = cdev_add(&jtag->cdev, MKDEV(MAJOR(jtag_devt), jtag->id), 1);
+ if (err)
+ goto err_cdev;
+
+ /* Register this jtag device with the driver core */
+ jtag->dev = device_create(&jtag_class, NULL, MKDEV(MAJOR(jtag_devt),
+ jtag->id),
+ NULL, "jtag%d", jtag->id);
+ if (!jtag->dev)
+ goto err_device_create;
+
+ dev_set_drvdata(jtag->dev, jtag);
+ spin_lock_init(&jtag->lock);
+ mutex_lock(&jtag_mutex);
+ list_add_tail(&jtag->list, &jtag_list);
+ mutex_unlock(&jtag_mutex);
+ return err;
+
+err_device_create:
+ cdev_del(&jtag->cdev);
+err_cdev:
+ ida_simple_remove(&jtag_ida, id);
+ return err;
+}
+EXPORT_SYMBOL_GPL(jtag_register);
+
+void jtag_unregister(struct jtag *jtag)
+{
+ struct device *dev = jtag->dev;
+
+ mutex_lock(&jtag_mutex);
+ list_del(&jtag->list);
+ mutex_unlock(&jtag_mutex);
+ cdev_del(&jtag->cdev);
+ device_unregister(dev);
+ ida_simple_remove(&jtag_ida, jtag->id);
+}
+EXPORT_SYMBOL_GPL(jtag_unregister);
+
+static int __init jtag_init(void)
+{
+ int err;
+
+ err = alloc_chrdev_region(&jtag_devt, 0, 1, "jtag");
+ if (err)
+ return err;
+ return class_register(&jtag_class);
+}
+
+static void __exit jtag_exit(void)
+{
+ class_unregister(&jtag_class);
+}
+
+module_init(jtag_init);
+module_exit(jtag_exit);
+
+MODULE_AUTHOR("Oleksandr Shamray <[email protected]>");
+MODULE_DESCRIPTION("Generic jtag support");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/jtag.h b/include/linux/jtag.h
new file mode 100644
index 0000000..418b5e8
--- /dev/null
+++ b/include/linux/jtag.h
@@ -0,0 +1,42 @@
+/*
+ * drivers/jtag/jtag.c
+ *
+ * Copyright (c) 2017 Mellanox Technologies. All rights reserved.
+ * Copyright (c) 2017 Oleksandr Shamray <[email protected]>
+ *
+ * Released under the GPLv2 only.
+ * SPDX-License-Identifier: GPL-2.0
+ */
+
+#ifndef __JTAG_H
+#define __JTAG_H
+
+#include <uapi/linux/jtag.h>
+
+#define JTAG_MAX_XFER_DATA_LEN 65535
+
+struct jtag;
+/**
+ * struct jtag_ops - callbacks for jtag control functions:
+ *
+ * @freq_get: get frequency function. Filled by device driver
+ * @freq_set: set frequency function. Filled by device driver
+ * @status_get: set status function. Filled by device driver
+ * @idle: set JTAG to idle state function. Filled by device driver
+ * @xfer: send JTAG xfer function. Filled by device driver
+ */
+struct jtag_ops {
+ int (*freq_get)(struct jtag *jtag, __u32 *freq);
+ int (*freq_set)(struct jtag *jtag, __u32 freq);
+ int (*status_get)(struct jtag *jtag, enum jtag_endstate *state);
+ int (*idle)(struct jtag *jtag, struct jtag_run_test_idle *idle);
+ int (*xfer)(struct jtag *jtag, struct jtag_xfer *xfer);
+};
+
+void *jtag_priv(struct jtag *jtag);
+int jtag_register(struct jtag *jtag);
+void jtag_unregister(struct jtag *jtag);
+struct jtag *jtag_alloc(size_t priv_size, const struct jtag_ops *ops);
+void jtag_free(struct jtag *jtag);
+
+#endif /* __JTAG_H */
diff --git a/include/uapi/linux/jtag.h b/include/uapi/linux/jtag.h
new file mode 100644
index 0000000..ebd4a8f
--- /dev/null
+++ b/include/uapi/linux/jtag.h
@@ -0,0 +1,113 @@
+/*
+ * JTAG class driver
+ *
+ * Copyright (c) 2017 Mellanox Technologies. All rights reserved.
+ * Copyright (c) 2017 Oleksandr Shamray <[email protected]>
+ *
+ * Released under the GPLv2/BSD.
+ * SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
+ */
+
+#ifndef __UAPI_LINUX_JTAG_H
+#define __UAPI_LINUX_JTAG_H
+
+#include <types.h>
+
+/**
+ * enum jtag_xfer_mode:
+ *
+ * @JTAG_XFER_HW_MODE: hardware mode transfer
+ * @JTAG_XFER_SW_MODE: software mode transfer
+ */
+enum jtag_xfer_mode {
+ JTAG_XFER_HW_MODE,
+ JTAG_XFER_SW_MODE,
+};
+
+/**
+ * enum jtag_endstate:
+ *
+ * @JTAG_STATE_IDLE: JTAG state machine IDLE state
+ * @JTAG_STATE_PAUSEIR: JTAG state machine PAUSE_IR state
+ * @JTAG_STATE_PAUSEDR: JTAG state machine PAUSE_DR state
+ */
+enum jtag_endstate {
+ JTAG_STATE_IDLE,
+ JTAG_STATE_PAUSEIR,
+ JTAG_STATE_PAUSEDR,
+};
+
+/**
+ * enum jtag_xfer_type:
+ *
+ * @JTAG_SIR_XFER: SIR transfer
+ * @JTAG_SDR_XFER: SDR transfer
+ */
+enum jtag_xfer_type {
+ JTAG_SIR_XFER,
+ JTAG_SDR_XFER,
+};
+
+/**
+ * enum jtag_xfer_direction:
+ *
+ * @JTAG_READ_XFER: read transfer
+ * @JTAG_WRITE_XFER: write transfer
+ */
+enum jtag_xfer_direction {
+ JTAG_READ_XFER,
+ JTAG_WRITE_XFER,
+};
+
+/**
+ * struct jtag_run_test_idle - forces JTAG state machine to
+ * RUN_TEST/IDLE state
+ *
+ * @mode: access mode
+ * @reset: 0 - run IDLE/PAUSE from current state
+ * 1 - go through TEST_LOGIC/RESET state before IDLE/PAUSE
+ * @end: completion flag
+ * @tck: clock counter
+ *
+ * Structure represents interface to JTAG device for jtag idle
+ * execution.
+ */
+struct jtag_run_test_idle {
+ __u8 mode;
+ __u8 reset;
+ __u8 endstate;
+ __u8 tck;
+};
+
+/**
+ * struct jtag_xfer - jtag xfer:
+ *
+ * @mode: access mode
+ * @type: transfer type
+ * @direction: xfer direction
+ * @length: xfer bits len
+ * @tdio : xfer data array
+ * @endir: xfer end state
+ *
+ * Structure represents interface to Aspeed JTAG device for jtag sdr xfer
+ * execution.
+ */
+struct jtag_xfer {
+ __u8 mode;
+ __u8 type;
+ __u8 direction;
+ __u32 length;
+ __u8 *tdio;
+ __u8 endstate;
+};
+
+#define __JTAG_IOCTL_MAGIC 0xb2
+
+#define JTAG_IOCRUNTEST _IOW(__JTAG_IOCTL_MAGIC, 0,\
+ struct jtag_run_test_idle)
+#define JTAG_SIOCFREQ _IOW(__JTAG_IOCTL_MAGIC, 1, unsigned int)
+#define JTAG_GIOCFREQ _IOR(__JTAG_IOCTL_MAGIC, 2, unsigned int)
+#define JTAG_IOCXFER _IOWR(__JTAG_IOCTL_MAGIC, 3, struct jtag_xfer)
+#define JTAG_GIOCSTATUS _IOWR(__JTAG_IOCTL_MAGIC, 4, enum jtag_endstate)
+
+#endif /* __UAPI_LINUX_JTAG_H */
--
1.7.1
Driver adds support of Aspeed 2500/2400 series SOC JTAG master controller.
Driver implements the following jtag ops:
- freq_get;
- freq_set;
- status_get;
- idle;
- xfer;
It has been tested on Mellanox system with BMC equipped with
Aspeed 2520 SoC for programming CPLD devices.
Signed-off-by: Jiri Pirko <[email protected]>
Signed-off-by: Oleksandr Shamray <[email protected]>
---
v1->v2
Comments pointed by Greg KH <[email protected]>
- change license type from GPLv2/BSD to GPLv2
Comments pointed by Neil Armstrong <[email protected]>
- Add clk_prepare_enable/clk_disable_unprepare in clock init/deinit
- Change .compatible to soc-specific compatible names
aspeed,aspeed4000-jtag/aspeed5000-jtag
- Added dt-bindings
Comments pointed by Arnd Bergmann <[email protected]>
- Reorder functions and removed the forward declarations
- Add static const qualifier to state machine states transitions
- Change .compatible to soc-specific compatible names
aspeed,aspeed4000-jtag/aspeed5000-jtag
- Add dt-bindings
Comments pointed by Randy Dunlap <[email protected]>
- Change module name jtag-aspeed in description in Kconfig
Comments pointed by kbuild test robot <[email protected]>
- Remove invalid include <asm/mach-types.h>
- add resource_size instead of calculation
---
.../devicetree/bindings/jtag/aspeed-jtag.txt | 27 +
drivers/jtag/Kconfig | 13 +
drivers/jtag/Makefile | 1 +
drivers/jtag/jtag-aspeed.c | 774 ++++++++++++++++++++
4 files changed, 815 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/jtag/aspeed-jtag.txt
create mode 100644 drivers/jtag/jtag-aspeed.c
diff --git a/Documentation/devicetree/bindings/jtag/aspeed-jtag.txt b/Documentation/devicetree/bindings/jtag/aspeed-jtag.txt
new file mode 100644
index 0000000..27b1d34
--- /dev/null
+++ b/Documentation/devicetree/bindings/jtag/aspeed-jtag.txt
@@ -0,0 +1,27 @@
+Aspeed JTAG driver for ast2400 and ast2500 SoC
+
+Required properties:
+- compatible: Should be one of
+ - "aspeed,aspeed2400-jtag"
+ - "aspeed,aspeed2500-jtag"
+- reg contains the offset and length of the JTAG memory
+ region
+- clocks root clock of bus, should reference the APB clock
+- reg-shift device register offsets are shifted by this value
+- interrupts should contain JTAG controller interrupt
+
+Optional properties:
+- status defines the operation status of the JTAG. Valid
+values are:
+ - "disabled" the JTAG is disabled
+ - "okay" the JTAG is enabled
+
+Example:
+jtag: jtag@1e6e4000 {
+ compatible = "aspeed,aspeed2500-jtag";
+ reg = <0x1e6e4000 0x1c>;
+ reg-shift = <2>;
+ clocks = <&clk_apb>;
+ interrupts = <43>;
+ status = "disabled";
+};
\ No newline at end of file
diff --git a/drivers/jtag/Kconfig b/drivers/jtag/Kconfig
index 0fad1a3..9f9bf94 100644
--- a/drivers/jtag/Kconfig
+++ b/drivers/jtag/Kconfig
@@ -14,3 +14,16 @@ menuconfig JTAG
To compile this driver as a module, choose M here: the module will
be called jtag.
+
+menuconfig JTAG_ASPEED
+ tristate "Aspeed SoC JTAG controller support"
+ depends on JTAG
+ ---help---
+ This provides a support for Aspeed JTAG device, equipped on
+ Aspeed SoC 24xx and 25xx families. Drivers allows programming
+ of hardware devices, connected to SoC through the JTAG interface.
+
+ If you want this support, you should say Y here.
+
+ To compile this driver as a module, choose M here: the module will
+ be called jtag-aspeed.
diff --git a/drivers/jtag/Makefile b/drivers/jtag/Makefile
index af37493..04a855e 100644
--- a/drivers/jtag/Makefile
+++ b/drivers/jtag/Makefile
@@ -1 +1,2 @@
obj-$(CONFIG_JTAG) += jtag.o
+obj-$(CONFIG_JTAG_ASPEED) += jtag-aspeed.o
diff --git a/drivers/jtag/jtag-aspeed.c b/drivers/jtag/jtag-aspeed.c
new file mode 100644
index 0000000..e8876e7
--- /dev/null
+++ b/drivers/jtag/jtag-aspeed.c
@@ -0,0 +1,774 @@
+/*
+ * drivers/jtag/jtag.c
+ *
+ * Copyright (c) 2017 Mellanox Technologies. All rights reserved.
+ * Copyright (c) 2017 Oleksandr Shamray <[email protected]>
+ *
+ * Released under the GPLv2 only.
+ * SPDX-License-Identifier: GPL-2.0
+ */
+
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/interrupt.h>
+#include <linux/jtag.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <uapi/linux/jtag.h>
+
+#define ASPEED_JTAG_DATA 0x00
+#define ASPEED_JTAG_INST 0x04
+#define ASPEED_JTAG_CTRL 0x08
+#define ASPEED_JTAG_ISR 0x0C
+#define ASPEED_JTAG_SW 0x10
+#define ASPEED_JTAG_TCK 0x14
+#define ASPEED_JTAG_EC 0x18
+
+#define ASPEED_JTAG_DATA_MSB 0x01
+#define ASPEED_JTAG_DATA_CHUNK_SIZE 0x20
+
+/* ASPEED_JTAG_CTRL: Engine Control */
+#define ASPEED_JTAG_CTL_ENG_EN BIT(31)
+#define ASPEED_JTAG_CTL_ENG_OUT_EN BIT(30)
+#define ASPEED_JTAG_CTL_FORCE_TMS BIT(29)
+#define ASPEED_JTAG_CTL_INST_LEN(x) ((x) << 20)
+#define ASPEED_JTAG_CTL_LASPEED_INST BIT(17)
+#define ASPEED_JTAG_CTL_INST_EN BIT(16)
+#define ASPEED_JTAG_CTL_DR_UPDATE BIT(10)
+#define ASPEED_JTAG_CTL_DATA_LEN(x) ((x) << 4)
+#define ASPEED_JTAG_CTL_LASPEED_DATA BIT(1)
+#define ASPEED_JTAG_CTL_DATA_EN BIT(0)
+
+/* ASPEED_JTAG_ISR : Interrupt status and enable */
+#define ASPEED_JTAG_ISR_INST_PAUSE BIT(19)
+#define ASPEED_JTAG_ISR_INST_COMPLETE BIT(18)
+#define ASPEED_JTAG_ISR_DATA_PAUSE BIT(17)
+#define ASPEED_JTAG_ISR_DATA_COMPLETE BIT(16)
+#define ASPEED_JTAG_ISR_INST_PAUSE_EN BIT(3)
+#define ASPEED_JTAG_ISR_INST_COMPLETE_EN BIT(2)
+#define ASPEED_JTAG_ISR_DATA_PAUSE_EN BIT(1)
+#define ASPEED_JTAG_ISR_DATA_COMPLETE_EN BIT(0)
+#define ASPEED_JTAG_ISR_INT_EN_MASK GENMASK(3, 0)
+#define ASPEED_JTAG_ISR_INT_MASK GENMASK(19, 16)
+
+/* ASPEED_JTAG_SW : Software Mode and Status */
+#define ASPEED_JTAG_SW_MODE_EN BIT(19)
+#define ASPEED_JTAG_SW_MODE_TCK BIT(18)
+#define ASPEED_JTAG_SW_MODE_TMS BIT(17)
+#define ASPEED_JTAG_SW_MODE_TDIO BIT(16)
+
+/* ASPEED_JTAG_TCK : TCK Control */
+#define ASPEED_JTAG_TCK_DIVISOR_MASK GENMASK(10, 0)
+#define ASPEED_JTAG_TCK_GET_DIV(x) ((x) & ASPEED_JTAG_TCK_DIVISOR_MASK)
+
+/* ASPEED_JTAG_EC : Controller set for go to IDLE */
+#define ASPEED_JTAG_EC_GO_IDLE BIT(0)
+
+#define ASPEED_JTAG_IOUT_LEN(len) (ASPEED_JTAG_CTL_ENG_EN |\
+ ASPEED_JTAG_CTL_ENG_OUT_EN |\
+ ASPEED_JTAG_CTL_INST_LEN(len))
+
+#define ASPEED_JTAG_DOUT_LEN(len) (ASPEED_JTAG_CTL_ENG_EN |\
+ ASPEED_JTAG_CTL_ENG_OUT_EN |\
+ ASPEED_JTAG_CTL_DATA_LEN(len))
+
+#define ASPEED_JTAG_TCK_WAIT 10
+#define ASPEED_JTAG_RESET_CNTR 10
+
+#define ASPEED_JTAG_NAME "jtag-aspeed"
+
+struct aspeed_jtag {
+ void __iomem *reg_base;
+ struct device *dev;
+ struct clk *pclk;
+ enum jtag_endstate status;
+ int irq;
+ u32 flag;
+ wait_queue_head_t jtag_wq;
+ bool is_open;
+};
+
+static char *end_status_str[] = {"idle", "ir pause", "drpause"};
+
+static u32 aspeed_jtag_read(struct aspeed_jtag *aspeed_jtag, u32 reg)
+{
+ return readl(aspeed_jtag->reg_base + reg);
+}
+
+static void
+aspeed_jtag_write(struct aspeed_jtag *aspeed_jtag, u32 val, u32 reg)
+{
+ writel(val, aspeed_jtag->reg_base + reg);
+}
+
+static int aspeed_jtag_freq_set(struct jtag *jtag, __u32 freq)
+{
+ struct aspeed_jtag *aspeed_jtag = jtag_priv(jtag);
+ unsigned long apb_frq;
+ u32 tck_val;
+ u16 div;
+
+ apb_frq = clk_get_rate(aspeed_jtag->pclk);
+ div = (apb_frq % freq == 0) ? (apb_frq / freq) - 1 : (apb_frq / freq);
+ tck_val = aspeed_jtag_read(aspeed_jtag, ASPEED_JTAG_TCK);
+ aspeed_jtag_write(aspeed_jtag,
+ (tck_val & ASPEED_JTAG_TCK_DIVISOR_MASK) | div,
+ ASPEED_JTAG_TCK);
+ return 0;
+}
+
+static int aspeed_jtag_freq_get(struct jtag *jtag, __u32 *frq)
+{
+ struct aspeed_jtag *aspeed_jtag = jtag_priv(jtag);
+ u32 pclk;
+ u32 tck;
+
+ pclk = clk_get_rate(aspeed_jtag->pclk);
+ tck = aspeed_jtag_read(aspeed_jtag, ASPEED_JTAG_TCK);
+ *frq = pclk / (ASPEED_JTAG_TCK_GET_DIV(tck) + 1);
+
+ return 0;
+}
+
+static void aspeed_jtag_sw_delay(struct aspeed_jtag *aspeed_jtag, int cnt)
+{
+ int i;
+
+ for (i = 0; i < cnt; i++)
+ aspeed_jtag_read(aspeed_jtag, ASPEED_JTAG_SW);
+}
+
+static char aspeed_jtag_tck_cycle(struct aspeed_jtag *aspeed_jtag,
+ u8 tms, u8 tdi)
+{
+ char tdo = 0;
+
+ /* TCK = 0 */
+ aspeed_jtag_write(aspeed_jtag, ASPEED_JTAG_SW_MODE_EN |
+ (tms * ASPEED_JTAG_SW_MODE_TMS) |
+ (tdi * ASPEED_JTAG_SW_MODE_TDIO), ASPEED_JTAG_SW);
+
+ aspeed_jtag_sw_delay(aspeed_jtag, ASPEED_JTAG_TCK_WAIT);
+
+ /* TCK = 1 */
+ aspeed_jtag_write(aspeed_jtag, ASPEED_JTAG_SW_MODE_EN |
+ ASPEED_JTAG_SW_MODE_TCK |
+ (tms * ASPEED_JTAG_SW_MODE_TMS) |
+ (tdi * ASPEED_JTAG_SW_MODE_TDIO), ASPEED_JTAG_SW);
+
+ if (aspeed_jtag_read(aspeed_jtag, ASPEED_JTAG_SW) &
+ ASPEED_JTAG_SW_MODE_TDIO)
+ tdo = 1;
+
+ aspeed_jtag_sw_delay(aspeed_jtag, ASPEED_JTAG_TCK_WAIT);
+
+ /* TCK = 0 */
+ aspeed_jtag_write(aspeed_jtag, ASPEED_JTAG_SW_MODE_EN |
+ (tms * ASPEED_JTAG_SW_MODE_TMS) |
+ (tdi * ASPEED_JTAG_SW_MODE_TDIO), ASPEED_JTAG_SW);
+ return tdo;
+}
+
+static void aspeed_jtag_wait_instruction_pause(struct aspeed_jtag *aspeed_jtag)
+{
+ wait_event_interruptible(aspeed_jtag->jtag_wq, aspeed_jtag->flag &
+ ASPEED_JTAG_ISR_INST_PAUSE);
+ aspeed_jtag->flag &= ~ASPEED_JTAG_ISR_INST_PAUSE;
+}
+
+static void
+aspeed_jtag_wait_instruction_complete(struct aspeed_jtag *aspeed_jtag)
+{
+ wait_event_interruptible(aspeed_jtag->jtag_wq, aspeed_jtag->flag &
+ ASPEED_JTAG_ISR_INST_COMPLETE);
+ aspeed_jtag->flag &= ~ASPEED_JTAG_ISR_INST_COMPLETE;
+}
+
+static void
+aspeed_jtag_wait_data_pause_complete(struct aspeed_jtag *aspeed_jtag)
+{
+ wait_event_interruptible(aspeed_jtag->jtag_wq, aspeed_jtag->flag &
+ ASPEED_JTAG_ISR_DATA_PAUSE);
+ aspeed_jtag->flag &= ~ASPEED_JTAG_ISR_DATA_PAUSE;
+}
+
+static void aspeed_jtag_wait_data_complete(struct aspeed_jtag *aspeed_jtag)
+{
+ wait_event_interruptible(aspeed_jtag->jtag_wq, aspeed_jtag->flag &
+ ASPEED_JTAG_ISR_DATA_COMPLETE);
+ aspeed_jtag->flag &= ~ASPEED_JTAG_ISR_DATA_COMPLETE;
+}
+
+static void aspeed_jtag_sm_cycle(struct aspeed_jtag *aspeed_jtag, const u8 *tms,
+ int len)
+{
+ int i;
+
+ for (i = 0; i < len; i++)
+ aspeed_jtag_tck_cycle(aspeed_jtag, tms[i], 0);
+}
+
+static void aspeed_jtag_run_test_idle_sw(struct aspeed_jtag *aspeed_jtag,
+ struct jtag_run_test_idle *runtest)
+{
+ static const char sm_pause_irpause[] = {1, 1, 1, 1, 0, 1, 0};
+ static const char sm_pause_drpause[] = {1, 1, 1, 0, 1, 0};
+ static const char sm_idle_irpause[] = {1, 1, 0, 1, 0};
+ static const char sm_idle_drpause[] = {1, 0, 1, 0};
+ static const char sm_pause_idle[] = {1, 1, 0};
+ int i;
+
+ /* SW mode from idle/pause-> to pause/idle */
+ if (runtest->reset) {
+ for (i = 0; i < ASPEED_JTAG_RESET_CNTR; i++)
+ aspeed_jtag_tck_cycle(aspeed_jtag, 1, 0);
+ }
+
+ switch (aspeed_jtag->status) {
+ case JTAG_STATE_IDLE:
+ switch (runtest->endstate) {
+ case JTAG_STATE_PAUSEIR:
+ /* ->DRSCan->IRSCan->IRCap->IRExit1->PauseIR */
+ aspeed_jtag_sm_cycle(aspeed_jtag, sm_idle_irpause,
+ sizeof(sm_idle_irpause));
+
+ aspeed_jtag->status = JTAG_STATE_PAUSEIR;
+ break;
+ case JTAG_STATE_PAUSEDR:
+ /* ->DRSCan->DRCap->DRExit1->PauseDR */
+ aspeed_jtag_sm_cycle(aspeed_jtag, sm_idle_drpause,
+ sizeof(sm_idle_drpause));
+
+ aspeed_jtag->status = JTAG_STATE_PAUSEDR;
+ break;
+ case JTAG_STATE_IDLE:
+ /* IDLE */
+ aspeed_jtag_tck_cycle(aspeed_jtag, 0, 0);
+ aspeed_jtag->status = JTAG_STATE_IDLE;
+ break;
+ default:
+ break;
+ }
+ break;
+
+ case JTAG_STATE_PAUSEIR:
+ /* Fall-through */
+ case JTAG_STATE_PAUSEDR:
+ /* From IR/DR Pause */
+ switch (runtest->endstate) {
+ case JTAG_STATE_PAUSEIR:
+ /*
+ * to Exit2 IR/DR->Updt IR/DR->DRSCan->IRSCan->IRCap->
+ * IRExit1->PauseIR
+ */
+ aspeed_jtag_sm_cycle(aspeed_jtag, sm_pause_irpause,
+ sizeof(sm_pause_irpause));
+
+ aspeed_jtag->status = JTAG_STATE_PAUSEIR;
+ break;
+ case JTAG_STATE_PAUSEDR:
+ /*
+ * to Exit2 IR/DR->Updt IR/DR->DRSCan->DRCap->
+ * DRExit1->PauseDR
+ */
+ aspeed_jtag_sm_cycle(aspeed_jtag, sm_pause_drpause,
+ sizeof(sm_pause_drpause));
+ aspeed_jtag->status = JTAG_STATE_PAUSEDR;
+ break;
+ case JTAG_STATE_IDLE:
+ /* to Exit2 IR/DR->Updt IR/DR->IDLE */
+ aspeed_jtag_sm_cycle(aspeed_jtag, sm_pause_idle,
+ sizeof(sm_pause_idle));
+ aspeed_jtag->status = JTAG_STATE_IDLE;
+ break;
+ default:
+ break;
+ }
+ break;
+
+ default:
+ dev_err(aspeed_jtag->dev, "aspeed_jtag_run_test_idle error\n");
+ break;
+ }
+
+ /* Stay on IDLE for at least TCK cycle */
+ for (i = 0; i < runtest->tck; i++)
+ aspeed_jtag_tck_cycle(aspeed_jtag, 0, 0);
+}
+
+/**
+ * aspeed_jtag_run_test_idle:
+ * JTAG reset: generates at least 9 TMS high and 1 TMS low to force
+ * devices into Run-Test/Idle State.
+ */
+static int aspeed_jtag_idle(struct jtag *jtag,
+ struct jtag_run_test_idle *runtest)
+{
+ struct aspeed_jtag *aspeed_jtag = jtag_priv(jtag);
+
+ dev_dbg(aspeed_jtag->dev, "aspeed_jtag runtest, status:%d, mode:%s, state:%s, reset:%d, tck:%d\n",
+ aspeed_jtag->status, runtest->mode ? "SW" : "HW",
+ end_status_str[runtest->endstate], runtest->reset,
+ runtest->tck);
+
+ if (runtest->mode) {
+ aspeed_jtag_run_test_idle_sw(aspeed_jtag, runtest);
+ return 0;
+ }
+
+ /* Disable sw mode */
+ aspeed_jtag_write(aspeed_jtag, 0, ASPEED_JTAG_SW);
+ /* x TMS high + 1 TMS low */
+ if (runtest->reset)
+ aspeed_jtag_write(aspeed_jtag, ASPEED_JTAG_CTL_ENG_EN |
+ ASPEED_JTAG_CTL_ENG_OUT_EN |
+ ASPEED_JTAG_CTL_FORCE_TMS, ASPEED_JTAG_CTRL);
+ else
+ aspeed_jtag_write(aspeed_jtag, ASPEED_JTAG_EC_GO_IDLE,
+ ASPEED_JTAG_EC);
+
+ aspeed_jtag_write(aspeed_jtag, ASPEED_JTAG_SW_MODE_EN |
+ ASPEED_JTAG_SW_MODE_TDIO, ASPEED_JTAG_SW);
+
+ aspeed_jtag->status = JTAG_STATE_IDLE;
+ return 0;
+}
+
+static void aspeed_jtag_xfer_sw(struct aspeed_jtag *aspeed_jtag,
+ struct jtag_xfer *xfer, char *tdio_data)
+{
+ unsigned long *data = (unsigned long *)tdio_data;
+ unsigned long remain_xfer = xfer->length;
+ unsigned long shift_bits = 0;
+ unsigned long index = 0;
+ unsigned long tdi;
+ char tdo;
+
+ if (xfer->direction == JTAG_READ_XFER)
+ tdi = UINT_MAX;
+ else
+ tdi = data[index];
+
+ while (remain_xfer > 1) {
+ tdo = aspeed_jtag_tck_cycle(aspeed_jtag, 0,
+ tdi & ASPEED_JTAG_DATA_MSB);
+ data[index] |= tdo << (shift_bits %
+ ASPEED_JTAG_DATA_CHUNK_SIZE);
+
+ tdi >>= 1;
+ shift_bits++;
+ remain_xfer--;
+
+ if (shift_bits % ASPEED_JTAG_DATA_CHUNK_SIZE == 0) {
+ dev_dbg(aspeed_jtag->dev, "R/W data[%lu]:%lx\n",
+ index, data[index]);
+
+ tdo = 0;
+ index++;
+
+ if (xfer->direction == JTAG_READ_XFER)
+ tdi = UINT_MAX;
+ else
+ tdi = data[index];
+ }
+ }
+
+ tdo = aspeed_jtag_tck_cycle(aspeed_jtag, 1, tdi & ASPEED_JTAG_DATA_MSB);
+ data[index] |= tdo << (shift_bits % ASPEED_JTAG_DATA_CHUNK_SIZE);
+}
+
+static void aspeed_jtag_xfer_push_data(struct aspeed_jtag *aspeed_jtag,
+ enum jtag_xfer_type type, u32 bits_len)
+{
+ dev_dbg(aspeed_jtag->dev, "shift bits %d\n", bits_len);
+
+ if (type == JTAG_SIR_XFER) {
+ aspeed_jtag_write(aspeed_jtag, ASPEED_JTAG_IOUT_LEN(bits_len),
+ ASPEED_JTAG_CTRL);
+ aspeed_jtag_write(aspeed_jtag, ASPEED_JTAG_DOUT_LEN(bits_len) |
+ ASPEED_JTAG_CTL_INST_EN, ASPEED_JTAG_CTRL);
+ } else {
+ aspeed_jtag_write(aspeed_jtag, ASPEED_JTAG_DOUT_LEN(bits_len),
+ ASPEED_JTAG_CTRL);
+ aspeed_jtag_write(aspeed_jtag, ASPEED_JTAG_DOUT_LEN(bits_len) |
+ ASPEED_JTAG_CTL_DATA_EN, ASPEED_JTAG_CTRL);
+ }
+}
+
+static void aspeed_jtag_xfer_push_data_last(struct aspeed_jtag *aspeed_jtag,
+ enum jtag_xfer_type type,
+ u32 shift_bits,
+ enum jtag_endstate endstate)
+{
+ if (endstate != JTAG_STATE_IDLE) {
+ if (type == JTAG_SIR_XFER) {
+ dev_dbg(aspeed_jtag->dev, "IR Keep Pause\n");
+
+ aspeed_jtag_write(aspeed_jtag,
+ ASPEED_JTAG_IOUT_LEN(shift_bits),
+ ASPEED_JTAG_CTRL);
+ aspeed_jtag_write(aspeed_jtag,
+ ASPEED_JTAG_IOUT_LEN(shift_bits) |
+ ASPEED_JTAG_CTL_INST_EN,
+ ASPEED_JTAG_CTRL);
+ aspeed_jtag_wait_instruction_pause(aspeed_jtag);
+ } else {
+ dev_dbg(aspeed_jtag->dev, "DR Keep Pause\n");
+ aspeed_jtag_write(aspeed_jtag,
+ ASPEED_JTAG_DOUT_LEN(shift_bits) |
+ ASPEED_JTAG_CTL_DR_UPDATE,
+ ASPEED_JTAG_CTRL);
+ aspeed_jtag_write(aspeed_jtag,
+ ASPEED_JTAG_DOUT_LEN(shift_bits) |
+ ASPEED_JTAG_CTL_DR_UPDATE |
+ ASPEED_JTAG_CTL_DATA_EN,
+ ASPEED_JTAG_CTRL);
+ aspeed_jtag_wait_data_pause_complete(aspeed_jtag);
+ }
+ } else {
+ if (type == JTAG_SIR_XFER) {
+ dev_dbg(aspeed_jtag->dev, "IR go IDLE\n");
+
+ aspeed_jtag_write(aspeed_jtag,
+ ASPEED_JTAG_IOUT_LEN(shift_bits) |
+ ASPEED_JTAG_CTL_LASPEED_INST,
+ ASPEED_JTAG_CTRL);
+ aspeed_jtag_write(aspeed_jtag,
+ ASPEED_JTAG_IOUT_LEN(shift_bits) |
+ ASPEED_JTAG_CTL_LASPEED_INST |
+ ASPEED_JTAG_CTL_INST_EN,
+ ASPEED_JTAG_CTRL);
+ aspeed_jtag_wait_instruction_complete(aspeed_jtag);
+ } else {
+ dev_dbg(aspeed_jtag->dev, "DR go IDLE\n");
+
+ aspeed_jtag_write(aspeed_jtag,
+ ASPEED_JTAG_DOUT_LEN(shift_bits) |
+ ASPEED_JTAG_CTL_LASPEED_DATA,
+ ASPEED_JTAG_CTRL);
+ aspeed_jtag_write(aspeed_jtag,
+ ASPEED_JTAG_DOUT_LEN(shift_bits) |
+ ASPEED_JTAG_CTL_LASPEED_DATA |
+ ASPEED_JTAG_CTL_DATA_EN,
+ ASPEED_JTAG_CTRL);
+ aspeed_jtag_wait_data_complete(aspeed_jtag);
+ }
+ }
+}
+
+static void aspeed_jtag_xfer_hw(struct aspeed_jtag *aspeed_jtag,
+ struct jtag_xfer *xfer, char *tdio_data)
+{
+ unsigned long *data = (unsigned long *)tdio_data;
+ unsigned long remain_xfer = xfer->length;
+ unsigned long index = 0;
+ char shift_bits;
+ u32 data_reg;
+
+ data_reg = xfer->type == JTAG_SIR_XFER ?
+ ASPEED_JTAG_INST : ASPEED_JTAG_DATA;
+ while (remain_xfer) {
+ if (xfer->direction == JTAG_WRITE_XFER) {
+ dev_dbg(aspeed_jtag->dev, "W dr->dr_data[%lu]:%lx\n",
+ index, data[index]);
+
+ aspeed_jtag_write(aspeed_jtag, data[index], data_reg);
+ } else {
+ aspeed_jtag_write(aspeed_jtag, 0, data_reg);
+ }
+
+ if (remain_xfer > ASPEED_JTAG_DATA_CHUNK_SIZE) {
+ shift_bits = ASPEED_JTAG_DATA_CHUNK_SIZE;
+
+ /*
+ * Read bytes were not equals to column length
+ * and go to Pause-DR
+ */
+ aspeed_jtag_xfer_push_data(aspeed_jtag, xfer->type,
+ shift_bits);
+ } else {
+ /*
+ * Read bytes equals to column length =>
+ * Update-DR
+ */
+ shift_bits = remain_xfer;
+ aspeed_jtag_xfer_push_data_last(aspeed_jtag, xfer->type,
+ shift_bits,
+ xfer->endstate);
+ }
+
+ if (xfer->direction == JTAG_READ_XFER) {
+ if (shift_bits < ASPEED_JTAG_DATA_CHUNK_SIZE) {
+ data[index] = aspeed_jtag_read(aspeed_jtag,
+ data_reg);
+
+ data[index] >>= ASPEED_JTAG_DATA_CHUNK_SIZE -
+ shift_bits;
+ } else {
+ data[index] = aspeed_jtag_read(aspeed_jtag,
+ data_reg);
+ }
+ dev_dbg(aspeed_jtag->dev, "R dr->dr_data[%lu]:%lx\n",
+ index, data[index]);
+ }
+
+ remain_xfer = remain_xfer - shift_bits;
+ index++;
+ dev_dbg(aspeed_jtag->dev, "remain_xfer %lu\n", remain_xfer);
+ }
+}
+
+static int aspeed_jtag_xfer(struct jtag *jtag, struct jtag_xfer *xfer)
+{
+ static const char sm_update_shiftir[] = {1, 1, 0, 0};
+ static const char sm_update_shiftdr[] = {1, 0, 0};
+ static const char sm_pause_idle[] = {1, 1, 0};
+ static const char sm_pause_update[] = {1, 1};
+ unsigned long *data = (unsigned long *)xfer->tdio;
+ struct aspeed_jtag *aspeed_jtag = jtag_priv(jtag);
+ unsigned long remain_xfer = xfer->length;
+ unsigned long offset;
+ char dbg_str[256];
+ int pos = 0;
+ int i;
+
+ for (offset = 0, i = 0; offset < xfer->length;
+ offset += ASPEED_JTAG_DATA_CHUNK_SIZE, i++) {
+ pos += snprintf(&dbg_str[pos], sizeof(dbg_str) - pos,
+ "0x%08lx ", data[i]);
+ }
+
+ dev_dbg(aspeed_jtag->dev, "aspeed_jtag %s %s xfer, mode:%s, END:%d, len:%lu, TDI[%s]\n",
+ xfer->type == JTAG_SIR_XFER ? "SIR" : "SDR",
+ xfer->direction == JTAG_READ_XFER ? "READ" : "WRITE",
+ xfer->mode ? "SW" : "HW",
+ xfer->endstate, remain_xfer, dbg_str);
+
+ if (xfer->mode == JTAG_XFER_SW_MODE) {
+ /* SW mode */
+ aspeed_jtag_write(aspeed_jtag, ASPEED_JTAG_SW_MODE_EN |
+ ASPEED_JTAG_SW_MODE_TDIO, ASPEED_JTAG_SW);
+
+ if (aspeed_jtag->status != JTAG_STATE_IDLE) {
+ /*IR/DR Pause->Exit2 IR / DR->Update IR /DR */
+ aspeed_jtag_sm_cycle(aspeed_jtag, sm_pause_update,
+ sizeof(sm_pause_update));
+ }
+
+ if (xfer->type == JTAG_SIR_XFER)
+ /* ->IRSCan->CapIR->ShiftIR */
+ aspeed_jtag_sm_cycle(aspeed_jtag, sm_update_shiftir,
+ sizeof(sm_update_shiftir));
+ else
+ /* ->DRScan->DRCap->DRShift */
+ aspeed_jtag_sm_cycle(aspeed_jtag, sm_update_shiftdr,
+ sizeof(sm_update_shiftdr));
+
+ aspeed_jtag_xfer_sw(aspeed_jtag, xfer, xfer->tdio);
+
+ /* DIPause/DRPause */
+ aspeed_jtag_tck_cycle(aspeed_jtag, 0, 0);
+
+ if (xfer->endstate == JTAG_STATE_IDLE) {
+ /* ->DRExit2->DRUpdate->IDLE */
+ aspeed_jtag_sm_cycle(aspeed_jtag, sm_pause_idle,
+ sizeof(sm_pause_idle));
+ }
+ } else {
+ /* hw mode */
+ aspeed_jtag_write(aspeed_jtag, 0, ASPEED_JTAG_SW);
+ aspeed_jtag_xfer_hw(aspeed_jtag, xfer, xfer->tdio);
+ }
+
+ aspeed_jtag_write(aspeed_jtag, ASPEED_JTAG_SW_MODE_EN |
+ ASPEED_JTAG_SW_MODE_TDIO, ASPEED_JTAG_SW);
+ aspeed_jtag->status = xfer->endstate;
+ return 0;
+}
+
+static int aspeed_jtag_status_get(struct jtag *jtag, enum jtag_endstate *status)
+{
+ struct aspeed_jtag *aspeed_jtag = jtag_priv(jtag);
+
+ *status = aspeed_jtag->status;
+ return 0;
+}
+
+static irqreturn_t aspeed_jtag_interrupt(s32 this_irq, void *dev_id)
+{
+ struct aspeed_jtag *aspeed_jtag = dev_id;
+ irqreturn_t ret;
+ u32 status;
+
+ status = aspeed_jtag_read(aspeed_jtag, ASPEED_JTAG_ISR);
+ dev_dbg(aspeed_jtag->dev, "status %x\n", status);
+
+ if (status & ASPEED_JTAG_ISR_INT_MASK) {
+ aspeed_jtag_write(aspeed_jtag,
+ (status & ASPEED_JTAG_ISR_INT_MASK)
+ | (status & ASPEED_JTAG_ISR_INT_EN_MASK),
+ ASPEED_JTAG_ISR);
+ aspeed_jtag->flag |= status & ASPEED_JTAG_ISR_INT_MASK;
+ }
+
+ if (aspeed_jtag->flag) {
+ wake_up_interruptible(&aspeed_jtag->jtag_wq);
+ ret = IRQ_HANDLED;
+ } else {
+ dev_err(aspeed_jtag->dev, "aspeed_jtag irq status:%x\n",
+ status);
+ ret = IRQ_NONE;
+ }
+ return ret;
+}
+
+int aspeed_jtag_init(struct platform_device *pdev,
+ struct aspeed_jtag *aspeed_jtag)
+{
+ struct resource *res;
+ int err;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ aspeed_jtag->reg_base = devm_ioremap_resource(aspeed_jtag->dev, res);
+ if (IS_ERR(aspeed_jtag->reg_base)) {
+ err = -ENOMEM;
+ goto out_region;
+ }
+
+ aspeed_jtag->pclk = devm_clk_get(aspeed_jtag->dev, NULL);
+ if (IS_ERR(aspeed_jtag->pclk)) {
+ dev_err(aspeed_jtag->dev, "devm_clk_get failed\n");
+ return PTR_ERR(aspeed_jtag->pclk);
+ }
+
+ clk_prepare_enable(aspeed_jtag->pclk);
+
+ aspeed_jtag->irq = platform_get_irq(pdev, 0);
+ if (aspeed_jtag->irq < 0) {
+ dev_err(aspeed_jtag->dev, "no irq specified\n");
+ err = -ENOENT;
+ goto out_region;
+ }
+
+ /* Enable clock */
+ aspeed_jtag_write(aspeed_jtag, ASPEED_JTAG_CTL_ENG_EN |
+ ASPEED_JTAG_CTL_ENG_OUT_EN, ASPEED_JTAG_CTRL);
+ aspeed_jtag_write(aspeed_jtag, ASPEED_JTAG_SW_MODE_EN |
+ ASPEED_JTAG_SW_MODE_TDIO, ASPEED_JTAG_SW);
+
+ err = devm_request_irq(aspeed_jtag->dev, aspeed_jtag->irq,
+ aspeed_jtag_interrupt, 0,
+ "aspeed-jtag", aspeed_jtag);
+ if (err) {
+ dev_err(aspeed_jtag->dev, "aspeed_jtag unable to get IRQ");
+ goto out_region;
+ }
+ dev_dbg(&pdev->dev, "aspeed_jtag:IRQ %d.\n", aspeed_jtag->irq);
+
+ aspeed_jtag_write(aspeed_jtag, ASPEED_JTAG_ISR_INST_PAUSE |
+ ASPEED_JTAG_ISR_INST_COMPLETE |
+ ASPEED_JTAG_ISR_DATA_PAUSE |
+ ASPEED_JTAG_ISR_DATA_COMPLETE |
+ ASPEED_JTAG_ISR_INST_PAUSE_EN |
+ ASPEED_JTAG_ISR_INST_COMPLETE_EN |
+ ASPEED_JTAG_ISR_DATA_PAUSE_EN |
+ ASPEED_JTAG_ISR_DATA_COMPLETE_EN,
+ ASPEED_JTAG_ISR);
+
+ aspeed_jtag->flag = 0;
+ init_waitqueue_head(&aspeed_jtag->jtag_wq);
+ return 0;
+
+out_region:
+ release_mem_region(res->start, resource_size(res));
+ return err;
+}
+
+int aspeed_jtag_deinit(struct platform_device *pdev,
+ struct aspeed_jtag *aspeed_jtag)
+{
+ aspeed_jtag_write(aspeed_jtag, 0, ASPEED_JTAG_ISR);
+ devm_free_irq(aspeed_jtag->dev, aspeed_jtag->irq, aspeed_jtag);
+ /* Disabe clock */
+ aspeed_jtag_write(aspeed_jtag, 0, ASPEED_JTAG_CTRL);
+ clk_disable_unprepare(aspeed_jtag->pclk);
+ return 0;
+}
+
+static const struct jtag_ops aspeed_jtag_ops = {
+ .freq_get = aspeed_jtag_freq_get,
+ .freq_set = aspeed_jtag_freq_set,
+ .status_get = aspeed_jtag_status_get,
+ .idle = aspeed_jtag_idle,
+ .xfer = aspeed_jtag_xfer
+};
+
+static int aspeed_jtag_probe(struct platform_device *pdev)
+{
+ struct aspeed_jtag *aspeed_jtag;
+ struct jtag *jtag;
+ int err;
+
+ if (!of_device_is_compatible(pdev->dev.of_node, "aspeed,aspeed-jtag"))
+ return -ENOMEM;
+
+ jtag = jtag_alloc(sizeof(*aspeed_jtag), &aspeed_jtag_ops);
+ if (!jtag)
+ return -ENODEV;
+
+ platform_set_drvdata(pdev, jtag);
+ aspeed_jtag = jtag_priv(jtag);
+ aspeed_jtag->dev = &pdev->dev;
+
+ /* Initialize device*/
+ err = aspeed_jtag_init(pdev, aspeed_jtag);
+ if (err)
+ goto err_jtag_init;
+
+ /* Initialize JTAG core structure*/
+ err = jtag_register(jtag);
+ if (err)
+ goto err_jtag_register;
+
+ return 0;
+
+err_jtag_register:
+ aspeed_jtag_deinit(pdev, aspeed_jtag);
+err_jtag_init:
+ jtag_free(jtag);
+ return err;
+}
+
+static int aspeed_jtag_remove(struct platform_device *pdev)
+{
+ struct jtag *jtag;
+
+ jtag = platform_get_drvdata(pdev);
+ aspeed_jtag_deinit(pdev, jtag_priv(jtag));
+ jtag_unregister(jtag);
+ jtag_free(jtag);
+ return 0;
+}
+
+static const struct of_device_id aspeed_jtag_of_match[] = {
+ { .compatible = "aspeed,aspeed2400-jtag", },
+ { .compatible = "aspeed,aspeed2500-jtag", },
+ {}
+};
+
+static struct platform_driver aspeed_jtag_driver = {
+ .probe = aspeed_jtag_probe,
+ .remove = aspeed_jtag_remove,
+ .driver = {
+ .name = ASPEED_JTAG_NAME,
+ .of_match_table = aspeed_jtag_of_match,
+ },
+};
+module_platform_driver(aspeed_jtag_driver);
+
+MODULE_AUTHOR("Oleksandr Shamray <[email protected]>");
+MODULE_DESCRIPTION("ASPEED JTAG driver");
+MODULE_LICENSE("GPL v2");
--
1.7.1
Hi Oleksandr,
[auto build test ERROR on linus/master]
[also build test ERROR on v4.13-rc4 next-20170808]
[if your patch is applied to the wrong git tree, please drop us a note to help improve the system]
url: https://github.com/0day-ci/linux/commits/Oleksandr-Shamray/drivers-jtag-Add-JTAG-core-driver/20170809-100030
config: i386-allmodconfig (attached as .config)
compiler: gcc-6 (Debian 6.2.0-3) 6.2.0 20160901
reproduce:
# save the attached .config to linux build tree
make ARCH=i386
All errors (new ones prefixed by >>):
In file included from include/linux/jtag.h:14:0,
from drivers/jtag/jtag.c:13:
>> include/uapi/linux/jtag.h:14:19: fatal error: types.h: No such file or directory
#include <types.h>
^
compilation terminated.
vim +14 include/uapi/linux/jtag.h
13
> 14 #include <types.h>
15
---
0-DAY kernel test infrastructure Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all Intel Corporation
On Mon, Aug 07, 2017 at 05:17:45PM +0300, Oleksandr Shamray wrote:
> When a need raise up to use JTAG interface for system's devices
> programming or CPU debugging, it could be done from the external
> JTAG master controller.
>
> For such purpose, usually the user layer
> application implements jtag protocol or using a proprietary
> connection to vendor hardware.
> This method is slow and not generic.
>
> We propose to implement general JTAG interface and infrastructure
> to communicate with user layer application.
Hi Oleksandr
You might find this discussion interesting:
https://lists.linuxfoundation.org/pipermail/ksummit-discuss/2017-August/004721.html
You are defining a new ABI here, so linux-abi should be involved in
the discussion of these patches.
Andrew
On Mon, Aug 07, 2017 at 05:17:45PM +0300, Oleksandr Shamray wrote:
> When a need raise up to use JTAG interface for system's devices
> programming or CPU debugging, it could be done from the external
> JTAG master controller.
Your subject line is a bit "odd" :(
On Mon, Aug 07, 2017 at 05:17:47PM +0300, Oleksandr Shamray wrote:
> Driver adds support of Aspeed 2500/2400 series SOC JTAG master controller.
>
> Driver implements the following jtag ops:
> - freq_get;
> - freq_set;
> - status_get;
> - idle;
> - xfer;
>
> It has been tested on Mellanox system with BMC equipped with
> Aspeed 2520 SoC for programming CPLD devices.
>
> Signed-off-by: Jiri Pirko <[email protected]>
> Signed-off-by: Oleksandr Shamray <[email protected]>
> ---
> v1->v2
> Comments pointed by Greg KH <[email protected]>
> - change license type from GPLv2/BSD to GPLv2
>
> Comments pointed by Neil Armstrong <[email protected]>
> - Add clk_prepare_enable/clk_disable_unprepare in clock init/deinit
> - Change .compatible to soc-specific compatible names
> aspeed,aspeed4000-jtag/aspeed5000-jtag
> - Added dt-bindings
>
> Comments pointed by Arnd Bergmann <[email protected]>
> - Reorder functions and removed the forward declarations
> - Add static const qualifier to state machine states transitions
> - Change .compatible to soc-specific compatible names
> aspeed,aspeed4000-jtag/aspeed5000-jtag
> - Add dt-bindings
>
> Comments pointed by Randy Dunlap <[email protected]>
> - Change module name jtag-aspeed in description in Kconfig
>
> Comments pointed by kbuild test robot <[email protected]>
> - Remove invalid include <asm/mach-types.h>
> - add resource_size instead of calculation
> ---
> .../devicetree/bindings/jtag/aspeed-jtag.txt | 27 +
Please split binding to separate patch.
> drivers/jtag/Kconfig | 13 +
> drivers/jtag/Makefile | 1 +
> drivers/jtag/jtag-aspeed.c | 774 ++++++++++++++++++++
> 4 files changed, 815 insertions(+), 0 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/jtag/aspeed-jtag.txt
> create mode 100644 drivers/jtag/jtag-aspeed.c
>
> diff --git a/Documentation/devicetree/bindings/jtag/aspeed-jtag.txt b/Documentation/devicetree/bindings/jtag/aspeed-jtag.txt
> new file mode 100644
> index 0000000..27b1d34
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/jtag/aspeed-jtag.txt
> @@ -0,0 +1,27 @@
> +Aspeed JTAG driver for ast2400 and ast2500 SoC
> +
> +Required properties:
> +- compatible: Should be one of
> + - "aspeed,aspeed2400-jtag"
> + - "aspeed,aspeed2500-jtag"
> +- reg contains the offset and length of the JTAG memory
> + region
> +- clocks root clock of bus, should reference the APB clock
> +- reg-shift device register offsets are shifted by this value
It doesn't appear that you use this. It should be implied by the
compatible in any case.
> +- interrupts should contain JTAG controller interrupt
> +
> +Optional properties:
> +- status defines the operation status of the JTAG. Valid
> +values are:
> + - "disabled" the JTAG is disabled
> + - "okay" the JTAG is enabled
Don't need to document status. It's implied for any node.
> +
> +Example:
> +jtag: jtag@1e6e4000 {
> + compatible = "aspeed,aspeed2500-jtag";
> + reg = <0x1e6e4000 0x1c>;
> + reg-shift = <2>;
> + clocks = <&clk_apb>;
> + interrupts = <43>;
> + status = "disabled";
Don't need to show status in examples either.
> +};
> \ No newline at end of file
^^^