2017-12-24 05:40:51

by Icenowy Zheng

[permalink] [raw]
Subject: [PATCH v3] ARM: sun8i: h2+: add support for Banana Pi M2 Zero board

Banana Pi M2 Zero board is a H2+-based board by Sinovoip, with a form
factor and GPIO holes similar to Raspberry Pi Zero.

It features:
- Allwinner H2+ SoC
- Single-chip (16-bit) 512MiB DDR3 DRAM
- Ampak AP6212 Wi-Fi/Bluetooth module
- MicroSD slot
- Two MicroUSB Type-B ports (one can only be used to power the board and
the other features OTG functionality)
- Two keys, a reset and a GPIO-connected key.
- HDMI Type-C (miniHDMI) connector connected to the HDMI part of H2+.
- CSI connector to connect the camera sensor provided by Sinovoip.

Signed-off-by: Icenowy Zheng <[email protected]>
---
Changes in v3:
- Add comments about Vbus problem in &usbphy node.

Changes in v2:
- Use high active SD card detect on the production batch.

arch/arm/boot/dts/Makefile | 1 +
.../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 162 +++++++++++++++++++++
2 files changed, 163 insertions(+)
create mode 100644 arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 0bb8db33704a..937a8768671f 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -962,6 +962,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-a83t-cubietruck-plus.dtb \
sun8i-a83t-tbs-a711.dtb \
sun8i-h2-plus-orangepi-r1.dtb \
+ sun8i-h2-plus-bananapi-m2-zero.dtb \
sun8i-h2-plus-orangepi-zero.dtb \
sun8i-h3-bananapi-m2-plus.dtb \
sun8i-h3-beelink-x2.dtb \
diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
new file mode 100644
index 000000000000..5bc182ddc5f7
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
@@ -0,0 +1,162 @@
+/*
+ * Copyright (C) 2017 Icenowy Zheng <[email protected]>
+ *
+ * Based on sun8i-h3-bananapi-m2-plus.dts, which is:
+ * Copyright (C) 2016 Chen-Yu Tsai <[email protected]>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Banana Pi BPI-M2-Zero";
+ compatible = "sinovoip,bpi-m2-zero", "allwinner,sun8i-h2-plus";
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+
+ pwr_led {
+ label = "bananapi-m2-zero:red:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
+ default-state = "on";
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+
+ sw4 {
+ label = "power";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>;
+ vmmc-supply = <&reg_vcc3v3>;
+ bus-width = <4>;
+ /*
+ * On the production batch of this board the card detect GPIO is
+ * high active (card inserted), although on the early samples it's
+ * low active.
+ */
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_a>;
+ vmmc-supply = <&reg_vcc3v3>;
+ vqmmc-supply = <&reg_vcc3v3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&pio>;
+ interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
+ interrupt-names = "host-wake";
+ };
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbphy {
+ usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+ /*
+ * There're two micro-USB connectors, one is power-only and another is
+ * OTG. The Vbus of these two connectors are connected together, so
+ * the external USB device will be powered just by the power input
+ * from the power-only USB port.
+ */
+ status = "okay";
+};
--
2.14.2


2017-12-24 08:02:28

by Priit Laes

[permalink] [raw]
Subject: Re: [linux-sunxi] [PATCH v3] ARM: sun8i: h2+: add support for Banana Pi M2 Zero board

On Sun, Dec 24, 2017 at 01:40:29PM +0800, Icenowy Zheng wrote:
> Banana Pi M2 Zero board is a H2+-based board by Sinovoip, with a form
> factor and GPIO holes similar to Raspberry Pi Zero.
>
> It features:
> - Allwinner H2+ SoC
> - Single-chip (16-bit) 512MiB DDR3 DRAM
> - Ampak AP6212 Wi-Fi/Bluetooth module
> - MicroSD slot
> - Two MicroUSB Type-B ports (one can only be used to power the board and
> the other features OTG functionality)
> - Two keys, a reset and a GPIO-connected key.
> - HDMI Type-C (miniHDMI) connector connected to the HDMI part of H2+.
> - CSI connector to connect the camera sensor provided by Sinovoip.
>
> Signed-off-by: Icenowy Zheng <[email protected]>
> ---
> Changes in v3:
> - Add comments about Vbus problem in &usbphy node.
>
> Changes in v2:
> - Use high active SD card detect on the production batch.
>
> arch/arm/boot/dts/Makefile | 1 +
> .../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 162 +++++++++++++++++++++
> 2 files changed, 163 insertions(+)
> create mode 100644 arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 0bb8db33704a..937a8768671f 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -962,6 +962,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
> sun8i-a83t-cubietruck-plus.dtb \
> sun8i-a83t-tbs-a711.dtb \
> sun8i-h2-plus-orangepi-r1.dtb \
> + sun8i-h2-plus-bananapi-m2-zero.dtb \
> sun8i-h2-plus-orangepi-zero.dtb \
> sun8i-h3-bananapi-m2-plus.dtb \
> sun8i-h3-beelink-x2.dtb \
> diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> new file mode 100644
> index 000000000000..5bc182ddc5f7
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> @@ -0,0 +1,162 @@
> +/*
> + * Copyright (C) 2017 Icenowy Zheng <[email protected]>
> + *
> + * Based on sun8i-h3-bananapi-m2-plus.dts, which is:
> + * Copyright (C) 2016 Chen-Yu Tsai <[email protected]>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "sun8i-h3.dtsi"
> +#include "sunxi-common-regulators.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> + model = "Banana Pi BPI-M2-Zero";
> + compatible = "sinovoip,bpi-m2-zero", "allwinner,sun8i-h2-plus";
> +
> + aliases {
> + serial0 = &uart0;
> + serial1 = &uart1;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> +
> + pwr_led {
> + label = "bananapi-m2-zero:red:pwr";
> + gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
> + default-state = "on";
> + };
> + };
> +
> + gpio_keys {
> + compatible = "gpio-keys";
> + pinctrl-names = "default";
> +
> + sw4 {
> + label = "power";
> + linux,code = <BTN_0>;
> + gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
> + };
> + };
> +
> + wifi_pwrseq: wifi_pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + pinctrl-names = "default";
> + reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
> + };
> +};
> +
> +&ehci0 {
> + status = "okay";
> +};
> +
> +&mmc0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc0_pins_a>;
> + vmmc-supply = <&reg_vcc3v3>;
> + bus-width = <4>;
> + /*
> + * On the production batch of this board the card detect GPIO is
> + * high active (card inserted), although on the early samples it's
> + * low active.
> + */

Is there a way to differentiate between early samples and production batches?
Board markings, etc?

> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
> + status = "okay";
> +};
> +
> +&mmc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc1_pins_a>;
> + vmmc-supply = <&reg_vcc3v3>;
> + vqmmc-supply = <&reg_vcc3v3>;
> + mmc-pwrseq = <&wifi_pwrseq>;
> + bus-width = <4>;
> + non-removable;
> + status = "okay";
> +
> + brcmf: wifi@1 {
> + reg = <1>;
> + compatible = "brcm,bcm4329-fmac";
> + interrupt-parent = <&pio>;
> + interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
> + interrupt-names = "host-wake";
> + };
> +};
> +
> +&ohci0 {
> + status = "okay";
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_pins_a>;
> + status = "okay";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
> + status = "okay";
> +};
> +
> +&usb_otg {
> + dr_mode = "otg";
> + status = "okay";
> +};
> +
> +&usbphy {
> + usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
> + /*
> + * There're two micro-USB connectors, one is power-only and another is
> + * OTG. The Vbus of these two connectors are connected together, so
> + * the external USB device will be powered just by the power input
> + * from the power-only USB port.
> + */
> + status = "okay";
> +};
> --
> 2.14.2
>
> --
> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to [email protected].
> For more options, visit https://groups.google.com/d/optout.

2017-12-24 12:25:11

by Icenowy Zheng

[permalink] [raw]
Subject: Re: [linux-sunxi] [PATCH v3] ARM: sun8i: h2+: add support for Banana Pi M2 Zero board

在 2017年12月24日星期日 CST 下午4:02:08,Priit Laes 写道:
> On Sun, Dec 24, 2017 at 01:40:29PM +0800, Icenowy Zheng wrote:
> > Banana Pi M2 Zero board is a H2+-based board by Sinovoip, with a form
> > factor and GPIO holes similar to Raspberry Pi Zero.
> >
> > It features:
> > - Allwinner H2+ SoC
> > - Single-chip (16-bit) 512MiB DDR3 DRAM
> > - Ampak AP6212 Wi-Fi/Bluetooth module
> > - MicroSD slot
> > - Two MicroUSB Type-B ports (one can only be used to power the board and
> >
> > the other features OTG functionality)
> >
> > - Two keys, a reset and a GPIO-connected key.
> > - HDMI Type-C (miniHDMI) connector connected to the HDMI part of H2+.
> > - CSI connector to connect the camera sensor provided by Sinovoip.
> >
> > Signed-off-by: Icenowy Zheng <[email protected]>
> > ---
> > Changes in v3:
> > - Add comments about Vbus problem in &usbphy node.
> >
> > Changes in v2:
> > - Use high active SD card detect on the production batch.
> >
> > arch/arm/boot/dts/Makefile | 1 +
> > .../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 162
> > +++++++++++++++++++++ 2 files changed, 163 insertions(+)
> > create mode 100644 arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> >
> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > index 0bb8db33704a..937a8768671f 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -962,6 +962,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
> >
> > sun8i-a83t-cubietruck-plus.dtb \
> > sun8i-a83t-tbs-a711.dtb \
> > sun8i-h2-plus-orangepi-r1.dtb \
> >
> > + sun8i-h2-plus-bananapi-m2-zero.dtb \
> >
> > sun8i-h2-plus-orangepi-zero.dtb \
> > sun8i-h3-bananapi-m2-plus.dtb \
> > sun8i-h3-beelink-x2.dtb \
> >
> > diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> > b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts new file mode
> > 100644
> > index 000000000000..5bc182ddc5f7
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> > @@ -0,0 +1,162 @@
> > +/*
> > + * Copyright (C) 2017 Icenowy Zheng <[email protected]>
> > + *
> > + * Based on sun8i-h3-bananapi-m2-plus.dts, which is:
> > + * Copyright (C) 2016 Chen-Yu Tsai <[email protected]>
> > + *
> > + * This file is dual-licensed: you can use it either under the terms
> > + * of the GPL or the X11 license, at your option. Note that this dual
> > + * licensing only applies to this file, and not this project as a
> > + * whole.
> > + *
> > + * a) This file is free software; you can redistribute it and/or
> > + * modify it under the terms of the GNU General Public License as
> > + * published by the Free Software Foundation; either version 2 of the
> > + * License, or (at your option) any later version.
> > + *
> > + * This file is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > + * GNU General Public License for more details.
> > + *
> > + * Or, alternatively,
> > + *
> > + * b) Permission is hereby granted, free of charge, to any person
> > + * obtaining a copy of this software and associated documentation
> > + * files (the "Software"), to deal in the Software without
> > + * restriction, including without limitation the rights to use,
> > + * copy, modify, merge, publish, distribute, sublicense, and/or
> > + * sell copies of the Software, and to permit persons to whom the
> > + * Software is furnished to do so, subject to the following
> > + * conditions:
> > + *
> > + * The above copyright notice and this permission notice shall be
> > + * included in all copies or substantial portions of the Software.
> > + *
> > + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> > + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> > + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> > + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> > + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> > + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> > + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> > + * OTHER DEALINGS IN THE SOFTWARE.
> > + */
> > +
> > +/dts-v1/;
> > +#include "sun8i-h3.dtsi"
> > +#include "sunxi-common-regulators.dtsi"
> > +
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/input/input.h>
> > +
> > +/ {
> > + model = "Banana Pi BPI-M2-Zero";
> > + compatible = "sinovoip,bpi-m2-zero", "allwinner,sun8i-h2-plus";
> > +
> > + aliases {
> > + serial0 = &uart0;
> > + serial1 = &uart1;
> > + };
> > +
> > + chosen {
> > + stdout-path = "serial0:115200n8";
> > + };
> > +
> > + leds {
> > + compatible = "gpio-leds";
> > + pinctrl-names = "default";
> > +
> > + pwr_led {
> > + label = "bananapi-m2-zero:red:pwr";
> > + gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
> > + default-state = "on";
> > + };
> > + };
> > +
> > + gpio_keys {
> > + compatible = "gpio-keys";
> > + pinctrl-names = "default";
> > +
> > + sw4 {
> > + label = "power";
> > + linux,code = <BTN_0>;
> > + gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
> > + };
> > + };
> > +
> > + wifi_pwrseq: wifi_pwrseq {
> > + compatible = "mmc-pwrseq-simple";
> > + pinctrl-names = "default";
> > + reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
> > + };
> > +};
> > +
> > +&ehci0 {
> > + status = "okay";
> > +};
> > +
> > +&mmc0 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&mmc0_pins_a>;
> > + vmmc-supply = <&reg_vcc3v3>;
> > + bus-width = <4>;
> > + /*
> > + * On the production batch of this board the card detect GPIO is
> > + * high active (card inserted), although on the early samples it's
> > + * low active.
> > + */
>
> Is there a way to differentiate between early samples and production
> batches? Board markings, etc?

in fact there's no significant markings to differentiate them.

Howeverm the early samples are never sold; you will know it's an
early sample if you manage to get it from Sinovoip.

>
> > + cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
> > + status = "okay";
> > +};
> > +
> > +&mmc1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&mmc1_pins_a>;
> > + vmmc-supply = <&reg_vcc3v3>;
> > + vqmmc-supply = <&reg_vcc3v3>;
> > + mmc-pwrseq = <&wifi_pwrseq>;
> > + bus-width = <4>;
> > + non-removable;
> > + status = "okay";
> > +
> > + brcmf: wifi@1 {
> > + reg = <1>;
> > + compatible = "brcm,bcm4329-fmac";
> > + interrupt-parent = <&pio>;
> > + interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
> > + interrupt-names = "host-wake";
> > + };
> > +};
> > +
> > +&ohci0 {
> > + status = "okay";
> > +};
> > +
> > +&uart0 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&uart0_pins_a>;
> > + status = "okay";
> > +};
> > +
> > +&uart1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
> > + status = "okay";
> > +};
> > +
> > +&usb_otg {
> > + dr_mode = "otg";
> > + status = "okay";
> > +};
> > +
> > +&usbphy {
> > + usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
> > + /*
> > + * There're two micro-USB connectors, one is power-only and another is
> > + * OTG. The Vbus of these two connectors are connected together, so
> > + * the external USB device will be powered just by the power input
> > + * from the power-only USB port.
> > + */
> > + status = "okay";
> > +};


2017-12-25 14:26:22

by Philippe Ombredanne

[permalink] [raw]
Subject: Re: [PATCH v3] ARM: sun8i: h2+: add support for Banana Pi M2 Zero board

On Sun, Dec 24, 2017 at 6:40 AM, Icenowy Zheng <[email protected]> wrote:
> Banana Pi M2 Zero board is a H2+-based board by Sinovoip, with a form
> factor and GPIO holes similar to Raspberry Pi Zero.
>
> It features:
> - Allwinner H2+ SoC
> - Single-chip (16-bit) 512MiB DDR3 DRAM
> - Ampak AP6212 Wi-Fi/Bluetooth module
> - MicroSD slot
> - Two MicroUSB Type-B ports (one can only be used to power the board and
> the other features OTG functionality)
> - Two keys, a reset and a GPIO-connected key.
> - HDMI Type-C (miniHDMI) connector connected to the HDMI part of H2+.
> - CSI connector to connect the camera sensor provided by Sinovoip.
>
> Signed-off-by: Icenowy Zheng <[email protected]>
> ---
> Changes in v3:
> - Add comments about Vbus problem in &usbphy node.
>
> Changes in v2:
> - Use high active SD card detect on the production batch.
>
> arch/arm/boot/dts/Makefile | 1 +
> .../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 162 +++++++++++++++++++++
> 2 files changed, 163 insertions(+)
> create mode 100644 arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 0bb8db33704a..937a8768671f 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -962,6 +962,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
> sun8i-a83t-cubietruck-plus.dtb \
> sun8i-a83t-tbs-a711.dtb \
> sun8i-h2-plus-orangepi-r1.dtb \
> + sun8i-h2-plus-bananapi-m2-zero.dtb \
> sun8i-h2-plus-orangepi-zero.dtb \
> sun8i-h3-bananapi-m2-plus.dtb \
> sun8i-h3-beelink-x2.dtb \
> diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> new file mode 100644
> index 000000000000..5bc182ddc5f7
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
> @@ -0,0 +1,162 @@
> +/*
> + * Copyright (C) 2017 Icenowy Zheng <[email protected]>
> + *
> + * Based on sun8i-h3-bananapi-m2-plus.dts, which is:
> + * Copyright (C) 2016 Chen-Yu Tsai <[email protected]>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +

Could you use SPDX tags instead of this long legalese?
--
Cordially
Philippe Ombredanne