A lot of changes in v2. The distributor and redistributor saving and
restoring is left to the PSCI/firmware implementation after
discussions with ARM. This reduces the line changes by a lot and
removes now unneeded patches.
Patches are verified on an RK3399 platform with pending patches in the
ARM-Trusted-Firmware project.
Just a couple minor changes in v3 to formatting.
Fixed a false ITS wedged detection due to the cmd_write and creadr
offsets not matching up on reset in v4. Also minor formatting changes.
Got rid of additional device tree property with detecting if there are
collections stored in the ITS in v5. Made other minor changes.
v6: Fixed reinitialized collections to only happen when the collection
is stored in the ITS. Changed error handling to avoid undefined
behavior of the ITS.
Derek Basehore (3):
irqchip/gic-v3-its: add ability to save/restore ITS state
DT/arm,gic-v3-its: add reset-on-suspend property
irqchip/gic-v3-its: add ability to resend MAPC on resume
.../bindings/interrupt-controller/arm,gic-v3.txt | 3 +
drivers/irqchip/irq-gic-v3-its.c | 189 ++++++++++++++++-----
include/linux/irqchip/arm-gic-v3.h | 1 +
3 files changed, 155 insertions(+), 38 deletions(-)
--
2.16.0.rc1.238.g530d649a79-goog
This adds functionality to resend the MAPC command to an ITS node on
resume. If the ITS is powered down during suspend and the collections
are not backed by memory, the ITS will lose that state. This just sets
up the known state for the collections after the ITS is restored.
This is enabled via the reset-on-suspend flag in the DTS. It only runs
for collections stored in the ITS itself.
Signed-off-by: Derek Basehore <[email protected]>
---
drivers/irqchip/irq-gic-v3-its.c | 86 +++++++++++++++++++++-----------------
include/linux/irqchip/arm-gic-v3.h | 1 +
2 files changed, 49 insertions(+), 38 deletions(-)
diff --git a/drivers/irqchip/irq-gic-v3-its.c b/drivers/irqchip/irq-gic-v3-its.c
index 35ad48f51dfa..a564a92ab169 100644
--- a/drivers/irqchip/irq-gic-v3-its.c
+++ b/drivers/irqchip/irq-gic-v3-its.c
@@ -1942,52 +1942,53 @@ static void its_cpu_init_lpis(void)
dsb(sy);
}
-static void its_cpu_init_collection(void)
+static void its_cpu_init_collection(struct its_node *its)
{
- struct its_node *its;
- int cpu;
-
- spin_lock(&its_lock);
- cpu = smp_processor_id();
-
- list_for_each_entry(its, &its_nodes, entry) {
- u64 target;
+ int cpu = smp_processor_id();
+ u64 target;
- /* avoid cross node collections and its mapping */
- if (its->flags & ITS_FLAGS_WORKAROUND_CAVIUM_23144) {
- struct device_node *cpu_node;
+ /* avoid cross node collections and its mapping */
+ if (its->flags & ITS_FLAGS_WORKAROUND_CAVIUM_23144) {
+ struct device_node *cpu_node;
- cpu_node = of_get_cpu_node(cpu, NULL);
- if (its->numa_node != NUMA_NO_NODE &&
- its->numa_node != of_node_to_nid(cpu_node))
- continue;
- }
+ cpu_node = of_get_cpu_node(cpu, NULL);
+ if (its->numa_node != NUMA_NO_NODE &&
+ its->numa_node != of_node_to_nid(cpu_node))
+ return;
+ }
+ /*
+ * We now have to bind each collection to its target
+ * redistributor.
+ */
+ if (gic_read_typer(its->base + GITS_TYPER) & GITS_TYPER_PTA) {
/*
- * We now have to bind each collection to its target
+ * This ITS wants the physical address of the
* redistributor.
*/
- if (gic_read_typer(its->base + GITS_TYPER) & GITS_TYPER_PTA) {
- /*
- * This ITS wants the physical address of the
- * redistributor.
- */
- target = gic_data_rdist()->phys_base;
- } else {
- /*
- * This ITS wants a linear CPU number.
- */
- target = gic_read_typer(gic_data_rdist_rd_base() + GICR_TYPER);
- target = GICR_TYPER_CPU_NUMBER(target) << 16;
- }
+ target = gic_data_rdist()->phys_base;
+ } else {
+ /* This ITS wants a linear CPU number. */
+ target = gic_read_typer(gic_data_rdist_rd_base() + GICR_TYPER);
+ target = GICR_TYPER_CPU_NUMBER(target) << 16;
+ }
- /* Perform collection mapping */
- its->collections[cpu].target_address = target;
- its->collections[cpu].col_id = cpu;
+ /* Perform collection mapping */
+ its->collections[cpu].target_address = target;
+ its->collections[cpu].col_id = cpu;
- its_send_mapc(its, &its->collections[cpu], 1);
- its_send_invall(its, &its->collections[cpu]);
- }
+ its_send_mapc(its, &its->collections[cpu], 1);
+ its_send_invall(its, &its->collections[cpu]);
+}
+
+static void its_cpu_init_collections(void)
+{
+ struct its_node *its;
+
+ spin_lock(&its_lock);
+
+ list_for_each_entry(its, &its_nodes, entry)
+ its_cpu_init_collection(its);
spin_unlock(&its_lock);
}
@@ -3131,6 +3132,15 @@ static void its_restore_enable(void)
its_write_baser(its, baser, baser->val);
}
writel_relaxed(its->ctlr_save, base + GITS_CTLR);
+
+ /*
+ * Reinit the collection if it's stored in the ITS. This is
+ * indicated by the col_id being less than the HWCOLLCNT.
+ * CID < HCC as specified in the GIC v3 Documentation.
+ */
+ if (its->collections[smp_processor_id()].col_id <
+ GITS_TYPER_HWCOLLCNT(gic_read_typer(base + GITS_TYPER)))
+ its_cpu_init_collection(its);
}
spin_unlock(&its_lock);
}
@@ -3397,7 +3407,7 @@ int its_cpu_init(void)
return -ENXIO;
}
its_cpu_init_lpis();
- its_cpu_init_collection();
+ its_cpu_init_collections();
}
return 0;
diff --git a/include/linux/irqchip/arm-gic-v3.h b/include/linux/irqchip/arm-gic-v3.h
index c00c4c33e432..c9c33b91a1f1 100644
--- a/include/linux/irqchip/arm-gic-v3.h
+++ b/include/linux/irqchip/arm-gic-v3.h
@@ -313,6 +313,7 @@
#define GITS_TYPER_DEVBITS(r) ((((r) >> GITS_TYPER_DEVBITS_SHIFT) & 0x1f) + 1)
#define GITS_TYPER_PTA (1UL << 19)
#define GITS_TYPER_HWCOLLCNT_SHIFT 24
+#define GITS_TYPER_HWCOLLCNT(r) (((r) >> GITS_TYPER_HWCOLLCNT_SHIFT) & 0xff)
#define GITS_TYPER_VMOVP (1ULL << 37)
#define GITS_IIDR_REV_SHIFT 12
--
2.16.0.rc1.238.g530d649a79-goog
This adds documentation for the new reset-on-suspend property. This
property enables saving and restoring the ITS for when it loses state
in system suspend.
Signed-off-by: Derek Basehore <[email protected]>
---
Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt | 3 +++
1 file changed, 3 insertions(+)
diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt
index 0a57f2f4167d..a470147d4f14 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt
+++ b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt
@@ -78,6 +78,9 @@ These nodes must have the following properties:
Optional:
- socionext,synquacer-pre-its: (u32, u32) tuple describing the untranslated
address and size of the pre-ITS window.
+- reset-on-suspend: Boolean property. Indicates that the ITS state is
+ reset on suspend. The state is then saved on suspend and restored on
+ resume.
The main GIC node must contain the appropriate #address-cells,
#size-cells and ranges properties for the reg property of all ITS
--
2.16.0.rc1.238.g530d649a79-goog
Some platforms power off GIC logic in suspend, so we need to
save/restore state. The distributor and redistributor registers need
to be handled in platform code due to access permissions on those
registers, but the ITS registers can be restored in the kernel.
Signed-off-by: Derek Basehore <[email protected]>
---
drivers/irqchip/irq-gic-v3-its.c | 103 +++++++++++++++++++++++++++++++++++++++
1 file changed, 103 insertions(+)
diff --git a/drivers/irqchip/irq-gic-v3-its.c b/drivers/irqchip/irq-gic-v3-its.c
index 06f025fd5726..35ad48f51dfa 100644
--- a/drivers/irqchip/irq-gic-v3-its.c
+++ b/drivers/irqchip/irq-gic-v3-its.c
@@ -33,6 +33,7 @@
#include <linux/of_platform.h>
#include <linux/percpu.h>
#include <linux/slab.h>
+#include <linux/syscore_ops.h>
#include <linux/irqchip.h>
#include <linux/irqchip/arm-gic-v3.h>
@@ -46,6 +47,7 @@
#define ITS_FLAGS_CMDQ_NEEDS_FLUSHING (1ULL << 0)
#define ITS_FLAGS_WORKAROUND_CAVIUM_22375 (1ULL << 1)
#define ITS_FLAGS_WORKAROUND_CAVIUM_23144 (1ULL << 2)
+#define ITS_FLAGS_SAVE_SUSPEND_STATE (1ULL << 3)
#define RDIST_FLAGS_PROPBASE_NEEDS_FLUSHING (1 << 0)
@@ -101,6 +103,8 @@ struct its_node {
struct its_collection *collections;
struct fwnode_handle *fwnode_handle;
u64 (*get_msi_base)(struct its_device *its_dev);
+ u64 cbaser_save;
+ u32 ctlr_save;
struct list_head its_device_list;
u64 flags;
unsigned long list_nr;
@@ -3042,6 +3046,100 @@ static void its_enable_quirks(struct its_node *its)
gic_enable_quirks(iidr, its_quirks, its);
}
+static int its_save_disable(void)
+{
+ struct its_node *its;
+ int err = 0;
+
+ spin_lock(&its_lock);
+ list_for_each_entry(its, &its_nodes, entry) {
+ void __iomem *base;
+
+ if (!(its->flags & ITS_FLAGS_SAVE_SUSPEND_STATE))
+ continue;
+
+ base = its->base;
+ its->ctlr_save = readl_relaxed(base + GITS_CTLR);
+ err = its_force_quiescent(base);
+ if (err) {
+ pr_err("ITS failed to quiesce\n");
+ writel_relaxed(its->ctlr_save, base + GITS_CTLR);
+ goto err;
+ }
+
+ its->cbaser_save = gits_read_cbaser(base + GITS_CBASER);
+ }
+
+err:
+ if (err) {
+ list_for_each_entry_continue_reverse(its, &its_nodes, entry) {
+ void __iomem *base;
+
+ if (!(its->flags & ITS_FLAGS_SAVE_SUSPEND_STATE))
+ continue;
+
+ base = its->base;
+ writel_relaxed(its->ctlr_save, base + GITS_CTLR);
+ }
+ }
+ spin_unlock(&its_lock);
+
+ return err;
+}
+
+static void its_restore_enable(void)
+{
+ struct its_node *its;
+
+ spin_lock(&its_lock);
+ list_for_each_entry(its, &its_nodes, entry) {
+ void __iomem *base;
+ int i;
+
+ if (!(its->flags & ITS_FLAGS_SAVE_SUSPEND_STATE))
+ continue;
+
+ base = its->base;
+
+ /*
+ * Make sure that the ITS is disabled. If it fails to quiesce,
+ * don't restore it since writing to CBASER or BASER<n>
+ * registers is undefined according to the GIC v3 ITS
+ * Specification.
+ */
+ if (its_force_quiescent(base)) {
+ pr_err("ITS(%p): failed to quiesce on resume\n", base);
+ continue;
+ }
+
+ gits_write_cbaser(its->cbaser_save, base + GITS_CBASER);
+
+ /*
+ * Writing CBASER resets CREADR to 0, so make CWRITER and
+ * cmd_write line up with it.
+ */
+ its->cmd_write = its->cmd_base;
+ gits_write_cwriter(0, base + GITS_CWRITER);
+
+ /* Restore GITS_BASER from the value cache. */
+ for (i = 0; i < GITS_BASER_NR_REGS; i++) {
+ struct its_baser *baser = &its->tables[i];
+
+ if (!(baser->val & GITS_BASER_VALID))
+ continue;
+
+ its_write_baser(its, baser, baser->val);
+ }
+ writel_relaxed(its->ctlr_save, base + GITS_CTLR);
+ }
+ spin_unlock(&its_lock);
+}
+
+static struct syscore_ops its_syscore_ops = {
+ .suspend = its_save_disable,
+ .resume = its_restore_enable,
+};
+
static int its_init_domain(struct fwnode_handle *handle, struct its_node *its)
{
struct irq_domain *inner_domain;
@@ -3261,6 +3359,9 @@ static int __init its_probe_one(struct resource *res,
ctlr |= GITS_CTLR_ImDe;
writel_relaxed(ctlr, its->base + GITS_CTLR);
+ if (fwnode_property_present(handle, "reset-on-suspend"))
+ its->flags |= ITS_FLAGS_SAVE_SUSPEND_STATE;
+
err = its_init_domain(handle, its);
if (err)
goto out_free_tables;
@@ -3515,5 +3616,7 @@ int __init its_init(struct fwnode_handle *handle, struct rdists *rdists,
}
}
+ register_syscore_ops(&its_syscore_ops);
+
return 0;
}
--
2.16.0.rc1.238.g530d649a79-goog
On Wed, Feb 07, 2018 at 06:36:47PM -0800, Derek Basehore wrote:
> This adds documentation for the new reset-on-suspend property. This
> property enables saving and restoring the ITS for when it loses state
> in system suspend.
>
> Signed-off-by: Derek Basehore <[email protected]>
> ---
> Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt | 3 +++
> 1 file changed, 3 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt
> index 0a57f2f4167d..a470147d4f14 100644
> --- a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt
> +++ b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt
> @@ -78,6 +78,9 @@ These nodes must have the following properties:
> Optional:
> - socionext,synquacer-pre-its: (u32, u32) tuple describing the untranslated
> address and size of the pre-ITS window.
> +- reset-on-suspend: Boolean property. Indicates that the ITS state is
> + reset on suspend. The state is then saved on suspend and restored on
> + resume.
The latter sentence reads like a description of SW policy, rather than a
description of what the HW does. I don't think that should be here
(though it might be worth noting the FW will not restore state).
Which state is lost? Is "ITS state" a well-defined term?
By suspend do you mean a PSCI_SYSTEM_SUSPEND, or potentially other
cases?
Thanks,
Mark.
Hi Derek,
On Wed, Feb 07, 2018 at 06:36:46PM -0800, Derek Basehore wrote:
> Some platforms power off GIC logic in suspend, so we need to
> save/restore state. The distributor and redistributor registers need
> to be handled in platform code due to access permissions on those
> registers, but the ITS registers can be restored in the kernel.
>
> Signed-off-by: Derek Basehore <[email protected]>
> ---
> drivers/irqchip/irq-gic-v3-its.c | 103 +++++++++++++++++++++++++++++++++++++++
> 1 file changed, 103 insertions(+)
>
> diff --git a/drivers/irqchip/irq-gic-v3-its.c b/drivers/irqchip/irq-gic-v3-its.c
> index 06f025fd5726..35ad48f51dfa 100644
> --- a/drivers/irqchip/irq-gic-v3-its.c
> +++ b/drivers/irqchip/irq-gic-v3-its.c
> @@ -33,6 +33,7 @@
> #include <linux/of_platform.h>
> #include <linux/percpu.h>
> #include <linux/slab.h>
> +#include <linux/syscore_ops.h>
>
> #include <linux/irqchip.h>
> #include <linux/irqchip/arm-gic-v3.h>
> @@ -46,6 +47,7 @@
> #define ITS_FLAGS_CMDQ_NEEDS_FLUSHING (1ULL << 0)
> #define ITS_FLAGS_WORKAROUND_CAVIUM_22375 (1ULL << 1)
> #define ITS_FLAGS_WORKAROUND_CAVIUM_23144 (1ULL << 2)
> +#define ITS_FLAGS_SAVE_SUSPEND_STATE (1ULL << 3)
>
> #define RDIST_FLAGS_PROPBASE_NEEDS_FLUSHING (1 << 0)
>
> @@ -101,6 +103,8 @@ struct its_node {
> struct its_collection *collections;
> struct fwnode_handle *fwnode_handle;
> u64 (*get_msi_base)(struct its_device *its_dev);
> + u64 cbaser_save;
> + u32 ctlr_save;
> struct list_head its_device_list;
> u64 flags;
> unsigned long list_nr;
> @@ -3042,6 +3046,100 @@ static void its_enable_quirks(struct its_node *its)
> gic_enable_quirks(iidr, its_quirks, its);
> }
>
> +static int its_save_disable(void)
> +{
> + struct its_node *its;
> + int err = 0;
> +
> + spin_lock(&its_lock);
> + list_for_each_entry(its, &its_nodes, entry) {
> + void __iomem *base;
> +
> + if (!(its->flags & ITS_FLAGS_SAVE_SUSPEND_STATE))
> + continue;
> +
> + base = its->base;
> + its->ctlr_save = readl_relaxed(base + GITS_CTLR);
> + err = its_force_quiescent(base);
> + if (err) {
> + pr_err("ITS failed to quiesce\n");
Isn't this a case where it was suggested to print the PA? Also, printing
the error code never hurts. Like:
pr_err("ITS@%pa: failed to quiesce: %d\n",
&its->phys_base, err);
> + writel_relaxed(its->ctlr_save, base + GITS_CTLR);
> + goto err;
> + }
> +
> + its->cbaser_save = gits_read_cbaser(base + GITS_CBASER);
> + }
> +
> +err:
> + if (err) {
> + list_for_each_entry_continue_reverse(its, &its_nodes, entry) {
> + void __iomem *base;
> +
> + if (!(its->flags & ITS_FLAGS_SAVE_SUSPEND_STATE))
> + continue;
> +
> + base = its->base;
> + writel_relaxed(its->ctlr_save, base + GITS_CTLR);
> + }
> + }
> + spin_unlock(&its_lock);
> +
> + return err;
> +}
> +
> +static void its_restore_enable(void)
> +{
> + struct its_node *its;
> +
> + spin_lock(&its_lock);
> + list_for_each_entry(its, &its_nodes, entry) {
> + void __iomem *base;
> + int i;
> +
> + if (!(its->flags & ITS_FLAGS_SAVE_SUSPEND_STATE))
> + continue;
> +
> + base = its->base;
> +
> + /*
> + * Make sure that the ITS is disabled. If it fails to quiesce,
> + * don't restore it since writing to CBASER or BASER<n>
> + * registers is undefined according to the GIC v3 ITS
> + * Specification.
> + */
> + if (its_force_quiescent(base)) {
> + pr_err("ITS(%p): failed to quiesce on resume\n", base);
I think Marc was requesting the PA, not the VA. The VA isn't really very
useful. Also, might as well log with similar style to the existing logs
(ITS@xxx), and log the error code:
pr_err("ITS@%pa: failed to quiesce on resume: %d\n",
&its->phys_base, ret);
Brian
> + continue;
> + }
> +
> + gits_write_cbaser(its->cbaser_save, base + GITS_CBASER);
> +
> + /*
> + * Writing CBASER resets CREADR to 0, so make CWRITER and
> + * cmd_write line up with it.
> + */
> + its->cmd_write = its->cmd_base;
> + gits_write_cwriter(0, base + GITS_CWRITER);
> +
> + /* Restore GITS_BASER from the value cache. */
> + for (i = 0; i < GITS_BASER_NR_REGS; i++) {
> + struct its_baser *baser = &its->tables[i];
> +
> + if (!(baser->val & GITS_BASER_VALID))
> + continue;
> +
> + its_write_baser(its, baser, baser->val);
> + }
> + writel_relaxed(its->ctlr_save, base + GITS_CTLR);
> + }
> + spin_unlock(&its_lock);
> +}
> +
> +static struct syscore_ops its_syscore_ops = {
> + .suspend = its_save_disable,
> + .resume = its_restore_enable,
> +};
> +
> static int its_init_domain(struct fwnode_handle *handle, struct its_node *its)
> {
> struct irq_domain *inner_domain;
> @@ -3261,6 +3359,9 @@ static int __init its_probe_one(struct resource *res,
> ctlr |= GITS_CTLR_ImDe;
> writel_relaxed(ctlr, its->base + GITS_CTLR);
>
> + if (fwnode_property_present(handle, "reset-on-suspend"))
> + its->flags |= ITS_FLAGS_SAVE_SUSPEND_STATE;
> +
> err = its_init_domain(handle, its);
> if (err)
> goto out_free_tables;
> @@ -3515,5 +3616,7 @@ int __init its_init(struct fwnode_handle *handle, struct rdists *rdists,
> }
> }
>
> + register_syscore_ops(&its_syscore_ops);
> +
> return 0;
> }
> --
> 2.16.0.rc1.238.g530d649a79-goog
>
On Wed, Feb 07, 2018 at 06:36:48PM -0800, Derek Basehore wrote:
> This adds functionality to resend the MAPC command to an ITS node on
> resume. If the ITS is powered down during suspend and the collections
> are not backed by memory, the ITS will lose that state. This just sets
> up the known state for the collections after the ITS is restored.
>
> This is enabled via the reset-on-suspend flag in the DTS. It only runs
> for collections stored in the ITS itself.
>
> Signed-off-by: Derek Basehore <[email protected]>
> ---
> drivers/irqchip/irq-gic-v3-its.c | 86 +++++++++++++++++++++-----------------
> include/linux/irqchip/arm-gic-v3.h | 1 +
> 2 files changed, 49 insertions(+), 38 deletions(-)
For the very little it's worth:
Reviewed-by: Brian Norris <[email protected]>