2018-04-19 02:03:07

by Baolin Wang

[permalink] [raw]
Subject: [PATCH v2 1/5] dmaengine: sprd: Define the DMA transfer step type

From: Eric Long <[email protected]>

Define the DMA transfer step type to make code more readable.

Signed-off-by: Eric Long <[email protected]>
Signed-off-by: Baolin Wang <[email protected]>
---
Changes since v1:
- Convert enum structure to macros definition for DMA step type.
---
drivers/dma/sprd-dma.c | 19 +++++++++++++------
1 file changed, 13 insertions(+), 6 deletions(-)

diff --git a/drivers/dma/sprd-dma.c b/drivers/dma/sprd-dma.c
index b106e8a..dcfa417 100644
--- a/drivers/dma/sprd-dma.c
+++ b/drivers/dma/sprd-dma.c
@@ -116,6 +116,13 @@
#define SPRD_DMA_SRC_TRSF_STEP_OFFSET 0
#define SPRD_DMA_TRSF_STEP_MASK GENMASK(15, 0)

+/* define the DMA transfer step type */
+#define SPRD_DMA_NONE_STEP 0
+#define SPRD_DMA_BYTE_STEP 1
+#define SPRD_DMA_SHORT_STEP 2
+#define SPRD_DMA_WORD_STEP 4
+#define SPRD_DMA_DWORD_STEP 8
+
#define SPRD_DMA_SOFTWARE_UID 0

/*
@@ -598,16 +605,16 @@ static int sprd_dma_config(struct dma_chan *chan, struct sprd_dma_desc *sdesc,

if (IS_ALIGNED(len, 4)) {
datawidth = 2;
- src_step = 4;
- des_step = 4;
+ src_step = SPRD_DMA_WORD_STEP;
+ des_step = SPRD_DMA_WORD_STEP;
} else if (IS_ALIGNED(len, 2)) {
datawidth = 1;
- src_step = 2;
- des_step = 2;
+ src_step = SPRD_DMA_SHORT_STEP;
+ des_step = SPRD_DMA_SHORT_STEP;
} else {
datawidth = 0;
- src_step = 1;
- des_step = 1;
+ src_step = SPRD_DMA_BYTE_STEP;
+ des_step = SPRD_DMA_BYTE_STEP;
}

fragment_len = SPRD_DMA_MEMCPY_MIN_SIZE;
--
1.7.9.5



2018-04-19 02:03:07

by Baolin Wang

[permalink] [raw]
Subject: [PATCH v2 4/5] dmaengine: sprd: Add Spreadtrum DMA configuration

From: Eric Long <[email protected]>

This patch adds one 'struct sprd_dma_config' structure to save Spreadtrum
DMA configuration for each DMA channel. Meanwhile we also did some optimization
for sprd_dma_config() and sprd_dma_prep_dma_memcpy() to prepare to configure
DMA from users.

Signed-off-by: Eric Long <[email protected]>
Signed-off-by: Baolin Wang <[email protected]>
---
Changes since v1:
- Remove 'struct sprd_dma_config' structure in 'sprd_dma.h'.
- Add 'struct sprd_dma_config' for DMA channel.
- Remove sprd_dma_get_datawidth() and sprd_dma_get_step().
- Other optimization.
---
drivers/dma/sprd-dma.c | 205 ++++++++++++++++++++++++++----------------------
1 file changed, 110 insertions(+), 95 deletions(-)

diff --git a/drivers/dma/sprd-dma.c b/drivers/dma/sprd-dma.c
index ccdeb8f..23846ed 100644
--- a/drivers/dma/sprd-dma.c
+++ b/drivers/dma/sprd-dma.c
@@ -100,6 +100,8 @@
#define SPRD_DMA_DES_DATAWIDTH_OFFSET 28
#define SPRD_DMA_SWT_MODE_OFFSET 26
#define SPRD_DMA_REQ_MODE_OFFSET 24
+#define SPRD_DMA_WRAP_SEL_OFFSET 23
+#define SPRD_DMA_WRAP_EN_OFFSET 22
#define SPRD_DMA_REQ_MODE_MASK GENMASK(1, 0)
#define SPRD_DMA_FIX_SEL_OFFSET 21
#define SPRD_DMA_FIX_EN_OFFSET 20
@@ -154,6 +156,41 @@ struct sprd_dma_chn_hw {
u32 des_blk_step;
};

+/*
+ * struct sprd_dma_config - DMA configuration structure
+ * @src_addr: the physical address where DMA slave data should be read
+ * @dst_addr: the physical address where DMA slave data should be written
+ * @fragment_len: specify one fragment transfer length
+ * @block_len: specify one block transfer length
+ * @transcation_len: specify one transcation transfer length
+ * @src_step: source transfer step
+ * @dst_step: destination transfer step
+ * @src_datawidth: source transfer data width
+ * @dst_datawidth: destination transfer data width
+ * @wrap_ptr: wrap pointer address, once the transfer address reaches the
+ * 'wrap_ptr', the next transfer address will jump to the 'wrap_to' address.
+ * @wrap_to: wrap jump to address
+ * @req_mode: specify the DMA request mode
+ * @int_mode: specify the DMA interrupt type
+ * @slave_id: slave channel requester id
+ */
+struct sprd_dma_config {
+ phys_addr_t src_addr;
+ phys_addr_t dst_addr;
+ u32 fragment_len;
+ u32 block_len;
+ u32 transcation_len;
+ u32 src_step;
+ u32 dst_step;
+ enum sprd_dma_datawidth src_datawidth;
+ enum sprd_dma_datawidth dst_datawidth;
+ phys_addr_t wrap_ptr;
+ phys_addr_t wrap_to;
+ enum sprd_dma_req_mode req_mode;
+ enum sprd_dma_int_type int_mode;
+ u32 slave_id;
+};
+
/* dma request description */
struct sprd_dma_desc {
struct virt_dma_desc vd;
@@ -164,6 +201,7 @@ struct sprd_dma_desc {
struct sprd_dma_chn {
struct virt_dma_chan vc;
void __iomem *chn_base;
+ struct sprd_dma_config slave_cfg;
u32 chn_num;
u32 dev_id;
struct sprd_dma_desc *cur_desc;
@@ -553,125 +591,74 @@ static void sprd_dma_issue_pending(struct dma_chan *chan)
}

static int sprd_dma_config(struct dma_chan *chan, struct sprd_dma_desc *sdesc,
- dma_addr_t dest, dma_addr_t src, size_t len)
+ struct sprd_dma_config *slave_cfg)
{
struct sprd_dma_dev *sdev = to_sprd_dma_dev(chan);
+ struct sprd_dma_chn *schan = to_sprd_dma_chan(chan);
struct sprd_dma_chn_hw *hw = &sdesc->chn_hw;
- u32 datawidth, src_step, des_step, fragment_len;
- u32 block_len, req_mode, irq_mode, transcation_len;
- u32 fix_mode = 0, fix_en = 0;
-
- if (IS_ALIGNED(len, 4)) {
- datawidth = SPRD_DMA_DATAWIDTH_4_BYTES;
- src_step = SPRD_DMA_WORD_STEP;
- des_step = SPRD_DMA_WORD_STEP;
- } else if (IS_ALIGNED(len, 2)) {
- datawidth = SPRD_DMA_DATAWIDTH_2_BYTES;
- src_step = SPRD_DMA_SHORT_STEP;
- des_step = SPRD_DMA_SHORT_STEP;
- } else {
- datawidth = SPRD_DMA_DATAWIDTH_1_BYTE;
- src_step = SPRD_DMA_BYTE_STEP;
- des_step = SPRD_DMA_BYTE_STEP;
- }
+ u32 fix_mode = 0, fix_en = 0, wrap_en = 0, wrap_mode = 0;

- fragment_len = SPRD_DMA_MEMCPY_MIN_SIZE;
- if (len <= SPRD_DMA_BLK_LEN_MASK) {
- block_len = len;
- transcation_len = 0;
- req_mode = SPRD_DMA_BLK_REQ;
- irq_mode = SPRD_DMA_BLK_INT;
- } else {
- block_len = SPRD_DMA_MEMCPY_MIN_SIZE;
- transcation_len = len;
- req_mode = SPRD_DMA_TRANS_REQ;
- irq_mode = SPRD_DMA_TRANS_INT;
- }
+ if (slave_cfg->slave_id)
+ schan->dev_id = slave_cfg->slave_id;

hw->cfg = SPRD_DMA_DONOT_WAIT_BDONE << SPRD_DMA_WAIT_BDONE_OFFSET;
- hw->wrap_ptr = (u32)((src >> SPRD_DMA_HIGH_ADDR_OFFSET) &
- SPRD_DMA_HIGH_ADDR_MASK);
- hw->wrap_to = (u32)((dest >> SPRD_DMA_HIGH_ADDR_OFFSET) &
- SPRD_DMA_HIGH_ADDR_MASK);
-
- hw->src_addr = (u32)(src & SPRD_DMA_LOW_ADDR_MASK);
- hw->des_addr = (u32)(dest & SPRD_DMA_LOW_ADDR_MASK);
-
- if ((src_step != 0 && des_step != 0) || (src_step | des_step) == 0) {
+ hw->wrap_ptr = (u32)((slave_cfg->wrap_ptr & SPRD_DMA_LOW_ADDR_MASK) |
+ ((slave_cfg->src_addr >> SPRD_DMA_HIGH_ADDR_OFFSET) &
+ SPRD_DMA_HIGH_ADDR_MASK));
+ hw->wrap_to = (u32)((slave_cfg->wrap_to & SPRD_DMA_LOW_ADDR_MASK) |
+ ((slave_cfg->dst_addr >> SPRD_DMA_HIGH_ADDR_OFFSET) &
+ SPRD_DMA_HIGH_ADDR_MASK));
+
+ hw->src_addr = (u32)(slave_cfg->src_addr & SPRD_DMA_LOW_ADDR_MASK);
+ hw->des_addr = (u32)(slave_cfg->dst_addr & SPRD_DMA_LOW_ADDR_MASK);
+
+ if ((slave_cfg->src_step != 0 && slave_cfg->dst_step != 0)
+ || (slave_cfg->src_step | slave_cfg->dst_step) == 0) {
fix_en = 0;
} else {
fix_en = 1;
- if (src_step)
+ if (slave_cfg->src_step)
fix_mode = 1;
else
fix_mode = 0;
}

- hw->frg_len = datawidth << SPRD_DMA_SRC_DATAWIDTH_OFFSET |
- datawidth << SPRD_DMA_DES_DATAWIDTH_OFFSET |
- req_mode << SPRD_DMA_REQ_MODE_OFFSET |
- fix_mode << SPRD_DMA_FIX_SEL_OFFSET |
- fix_en << SPRD_DMA_FIX_EN_OFFSET |
- (fragment_len & SPRD_DMA_FRG_LEN_MASK);
- hw->blk_len = block_len & SPRD_DMA_BLK_LEN_MASK;
-
- hw->intc = SPRD_DMA_CFG_ERR_INT_EN;
-
- switch (irq_mode) {
- case SPRD_DMA_NO_INT:
- break;
-
- case SPRD_DMA_FRAG_INT:
- hw->intc |= SPRD_DMA_FRAG_INT_EN;
- break;
-
- case SPRD_DMA_BLK_INT:
- hw->intc |= SPRD_DMA_BLK_INT_EN;
- break;
-
- case SPRD_DMA_BLK_FRAG_INT:
- hw->intc |= SPRD_DMA_BLK_INT_EN | SPRD_DMA_FRAG_INT_EN;
- break;
-
- case SPRD_DMA_TRANS_INT:
- hw->intc |= SPRD_DMA_TRANS_INT_EN;
- break;
-
- case SPRD_DMA_TRANS_FRAG_INT:
- hw->intc |= SPRD_DMA_TRANS_INT_EN | SPRD_DMA_FRAG_INT_EN;
- break;
+ if (slave_cfg->wrap_ptr && slave_cfg->wrap_to) {
+ wrap_en = 1;
+ if (slave_cfg->wrap_to == slave_cfg->src_addr) {
+ wrap_mode = 0;
+ } else if (slave_cfg->wrap_to == slave_cfg->dst_addr) {
+ wrap_mode = 1;
+ } else {
+ dev_err(sdev->dma_dev.dev, "invalid wrap mode\n");
+ return -EINVAL;
+ }
+ }

- case SPRD_DMA_TRANS_BLK_INT:
- hw->intc |= SPRD_DMA_TRANS_INT_EN | SPRD_DMA_BLK_INT_EN;
- break;
+ hw->intc = slave_cfg->int_mode | SPRD_DMA_CFG_ERR_INT_EN;

- case SPRD_DMA_LIST_INT:
- hw->intc |= SPRD_DMA_LIST_INT_EN;
- break;
+ hw->frg_len =
+ slave_cfg->src_datawidth << SPRD_DMA_SRC_DATAWIDTH_OFFSET |
+ slave_cfg->dst_datawidth << SPRD_DMA_DES_DATAWIDTH_OFFSET |
+ slave_cfg->req_mode << SPRD_DMA_REQ_MODE_OFFSET |
+ wrap_mode << SPRD_DMA_WRAP_SEL_OFFSET |
+ wrap_en << SPRD_DMA_WRAP_EN_OFFSET |
+ fix_mode << SPRD_DMA_FIX_SEL_OFFSET |
+ fix_en << SPRD_DMA_FIX_EN_OFFSET |
+ (slave_cfg->fragment_len & SPRD_DMA_FRG_LEN_MASK);

- case SPRD_DMA_CFGERR_INT:
- hw->intc |= SPRD_DMA_CFG_ERR_INT_EN;
- break;
+ hw->blk_len = slave_cfg->block_len & SPRD_DMA_BLK_LEN_MASK;

- default:
- dev_err(sdev->dma_dev.dev, "invalid irq mode\n");
- return -EINVAL;
- }
+ hw->trsc_len = slave_cfg->transcation_len & SPRD_DMA_TRSC_LEN_MASK;

- if (transcation_len == 0)
- hw->trsc_len = block_len & SPRD_DMA_TRSC_LEN_MASK;
- else
- hw->trsc_len = transcation_len & SPRD_DMA_TRSC_LEN_MASK;
-
- hw->trsf_step = (des_step & SPRD_DMA_TRSF_STEP_MASK) <<
+ hw->trsf_step = (slave_cfg->dst_step & SPRD_DMA_TRSF_STEP_MASK) <<
SPRD_DMA_DEST_TRSF_STEP_OFFSET |
- (src_step & SPRD_DMA_TRSF_STEP_MASK) <<
+ (slave_cfg->src_step & SPRD_DMA_TRSF_STEP_MASK) <<
SPRD_DMA_SRC_TRSF_STEP_OFFSET;

hw->frg_step = 0;
hw->src_blk_step = 0;
hw->des_blk_step = 0;
- hw->src_blk_step = 0;
return 0;
}

@@ -680,6 +667,7 @@ static int sprd_dma_config(struct dma_chan *chan, struct sprd_dma_desc *sdesc,
size_t len, unsigned long flags)
{
struct sprd_dma_chn *schan = to_sprd_dma_chan(chan);
+ struct sprd_dma_config *slave_cfg = &schan->slave_cfg;
struct sprd_dma_desc *sdesc;
int ret;

@@ -687,7 +675,34 @@ static int sprd_dma_config(struct dma_chan *chan, struct sprd_dma_desc *sdesc,
if (!sdesc)
return NULL;

- ret = sprd_dma_config(chan, sdesc, dest, src, len);
+ memset(slave_cfg, 0, sizeof(*slave_cfg));
+
+ slave_cfg->src_addr = src;
+ slave_cfg->dst_addr = dest;
+ slave_cfg->fragment_len = len;
+ slave_cfg->block_len = len;
+ slave_cfg->transcation_len = len;
+ slave_cfg->req_mode = SPRD_DMA_TRANS_REQ;
+ slave_cfg->int_mode = SPRD_DMA_TRANS_INT;
+
+ if (IS_ALIGNED(len, 4)) {
+ slave_cfg->src_datawidth = SPRD_DMA_DATAWIDTH_4_BYTES;
+ slave_cfg->dst_datawidth = SPRD_DMA_DATAWIDTH_4_BYTES;
+ slave_cfg->src_step = SPRD_DMA_WORD_STEP;
+ slave_cfg->dst_step = SPRD_DMA_WORD_STEP;
+ } else if (IS_ALIGNED(len, 2)) {
+ slave_cfg->src_datawidth = SPRD_DMA_DATAWIDTH_2_BYTES;
+ slave_cfg->dst_datawidth = SPRD_DMA_DATAWIDTH_2_BYTES;
+ slave_cfg->src_step = SPRD_DMA_SHORT_STEP;
+ slave_cfg->dst_step = SPRD_DMA_SHORT_STEP;
+ } else {
+ slave_cfg->src_datawidth = SPRD_DMA_DATAWIDTH_1_BYTE;
+ slave_cfg->dst_datawidth = SPRD_DMA_DATAWIDTH_1_BYTE;
+ slave_cfg->src_step = SPRD_DMA_BYTE_STEP;
+ slave_cfg->dst_step = SPRD_DMA_BYTE_STEP;
+ }
+
+ ret = sprd_dma_config(chan, sdesc, slave_cfg);
if (ret) {
kfree(sdesc);
return NULL;
--
1.7.9.5


2018-04-19 02:03:25

by Baolin Wang

[permalink] [raw]
Subject: [PATCH v2 5/5] dmaengine: sprd: Add 'device_config' and 'device_prep_slave_sg' interfaces

From: Eric Long <[email protected]>

This patch adds the 'device_config' and 'device_prep_slave_sg' interfaces
for users to configure DMA.

Signed-off-by: Eric Long <[email protected]>
Signed-off-by: Baolin Wang <[email protected]>
---
Changes since v1:
- The request mode and interrupt type will be passed from flags.
- Add sprd_dma_get_step() to get src/dst step.
- Add sprd_dma_get_datawidth() to convert data width values which
can be used by Spreadtrum DMA.
---
drivers/dma/sprd-dma.c | 115 ++++++++++++++++++++++++++++++++++++++++++
include/linux/dma/sprd-dma.h | 4 ++
2 files changed, 119 insertions(+)

diff --git a/drivers/dma/sprd-dma.c b/drivers/dma/sprd-dma.c
index 23846ed..f2598ed 100644
--- a/drivers/dma/sprd-dma.c
+++ b/drivers/dma/sprd-dma.c
@@ -590,6 +590,47 @@ static void sprd_dma_issue_pending(struct dma_chan *chan)
spin_unlock_irqrestore(&schan->vc.lock, flags);
}

+static enum sprd_dma_datawidth
+sprd_dma_get_datawidth(enum dma_slave_buswidth buswidth)
+{
+ switch (buswidth) {
+ case DMA_SLAVE_BUSWIDTH_1_BYTE:
+ return SPRD_DMA_DATAWIDTH_1_BYTE;
+
+ case DMA_SLAVE_BUSWIDTH_2_BYTES:
+ return SPRD_DMA_DATAWIDTH_2_BYTES;
+
+ case DMA_SLAVE_BUSWIDTH_4_BYTES:
+ return SPRD_DMA_DATAWIDTH_4_BYTES;
+
+ case DMA_SLAVE_BUSWIDTH_8_BYTES:
+ return SPRD_DMA_DATAWIDTH_8_BYTES;
+
+ default:
+ return SPRD_DMA_DATAWIDTH_4_BYTES;
+ }
+}
+
+static u32 sprd_dma_get_step(enum sprd_dma_datawidth datawidth)
+{
+ switch (datawidth) {
+ case SPRD_DMA_DATAWIDTH_1_BYTE:
+ return SPRD_DMA_BYTE_STEP;
+
+ case SPRD_DMA_DATAWIDTH_2_BYTES:
+ return SPRD_DMA_SHORT_STEP;
+
+ case SPRD_DMA_DATAWIDTH_4_BYTES:
+ return SPRD_DMA_WORD_STEP;
+
+ case SPRD_DMA_DATAWIDTH_8_BYTES:
+ return SPRD_DMA_DWORD_STEP;
+
+ default:
+ return SPRD_DMA_DWORD_STEP;
+ }
+}
+
static int sprd_dma_config(struct dma_chan *chan, struct sprd_dma_desc *sdesc,
struct sprd_dma_config *slave_cfg)
{
@@ -711,6 +752,78 @@ static int sprd_dma_config(struct dma_chan *chan, struct sprd_dma_desc *sdesc,
return vchan_tx_prep(&schan->vc, &sdesc->vd, flags);
}

+static struct dma_async_tx_descriptor *
+sprd_dma_prep_slave_sg(struct dma_chan *chan, struct scatterlist *sgl,
+ unsigned int sglen, enum dma_transfer_direction dir,
+ unsigned long flags, void *context)
+{
+ struct sprd_dma_chn *schan = to_sprd_dma_chan(chan);
+ struct sprd_dma_config *slave_cfg = &schan->slave_cfg;
+ struct sprd_dma_desc *sdesc;
+ struct scatterlist *sg;
+ int ret, i;
+
+ /* TODO: now we only support one sg for each DMA configuration. */
+ if (!is_slave_direction(dir) || sglen > 1)
+ return NULL;
+
+ sdesc = kzalloc(sizeof(*sdesc), GFP_NOWAIT);
+ if (!sdesc)
+ return NULL;
+
+ for_each_sg(sgl, sg, sglen, i) {
+ if (dir == DMA_MEM_TO_DEV) {
+ slave_cfg->src_addr = sg_dma_address(sg);
+ slave_cfg->src_step =
+ sprd_dma_get_step(slave_cfg->src_datawidth);
+ slave_cfg->dst_step = SPRD_DMA_NONE_STEP;
+ } else {
+ slave_cfg->dst_addr = sg_dma_address(sg);
+ slave_cfg->src_step = SPRD_DMA_NONE_STEP;
+ slave_cfg->dst_step =
+ sprd_dma_get_step(slave_cfg->dst_datawidth);
+ }
+
+ slave_cfg->block_len = sg_dma_len(sg);
+ slave_cfg->transcation_len = sg_dma_len(sg);
+ }
+
+ slave_cfg->req_mode =
+ (flags >> SPRD_DMA_REQ_SHIFT) & SPRD_DMA_REQ_MODE_MASK;
+ slave_cfg->int_mode = flags & SPRD_DMA_INT_MASK;
+
+ ret = sprd_dma_config(chan, sdesc, slave_cfg);
+ if (ret) {
+ kfree(sdesc);
+ return NULL;
+ }
+
+ return vchan_tx_prep(&schan->vc, &sdesc->vd, flags);
+}
+
+static int sprd_dma_slave_config(struct dma_chan *chan,
+ struct dma_slave_config *config)
+{
+ struct sprd_dma_chn *schan = to_sprd_dma_chan(chan);
+ struct sprd_dma_config *slave_cfg = &schan->slave_cfg;
+
+ if (!is_slave_direction(config->direction))
+ return -EINVAL;
+
+ memset(slave_cfg, 0, sizeof(*slave_cfg));
+
+ slave_cfg->slave_id = config->slave_id;
+ slave_cfg->src_addr = config->src_addr;
+ slave_cfg->dst_addr = config->dst_addr;
+ slave_cfg->fragment_len = config->src_maxburst;
+ slave_cfg->src_datawidth =
+ sprd_dma_get_datawidth(config->src_addr_width);
+ slave_cfg->dst_datawidth =
+ sprd_dma_get_datawidth(config->dst_addr_width);
+
+ return 0;
+}
+
static int sprd_dma_pause(struct dma_chan *chan)
{
struct sprd_dma_chn *schan = to_sprd_dma_chan(chan);
@@ -838,6 +951,8 @@ static int sprd_dma_probe(struct platform_device *pdev)
sdev->dma_dev.device_tx_status = sprd_dma_tx_status;
sdev->dma_dev.device_issue_pending = sprd_dma_issue_pending;
sdev->dma_dev.device_prep_dma_memcpy = sprd_dma_prep_dma_memcpy;
+ sdev->dma_dev.device_prep_slave_sg = sprd_dma_prep_slave_sg;
+ sdev->dma_dev.device_config = sprd_dma_slave_config;
sdev->dma_dev.device_pause = sprd_dma_pause;
sdev->dma_dev.device_resume = sprd_dma_resume;
sdev->dma_dev.device_terminate_all = sprd_dma_terminate_all;
diff --git a/include/linux/dma/sprd-dma.h b/include/linux/dma/sprd-dma.h
index c545162..b0115e3 100644
--- a/include/linux/dma/sprd-dma.h
+++ b/include/linux/dma/sprd-dma.h
@@ -3,6 +3,10 @@
#ifndef _SPRD_DMA_H_
#define _SPRD_DMA_H_

+#define SPRD_DMA_REQ_SHIFT 16
+#define SPRD_DMA_FLAGS(req_mode, int_type) \
+ ((req_mode) << SPRD_DMA_REQ_SHIFT | (int_type))
+
/*
* enum sprd_dma_req_mode: define the DMA request mode
* @SPRD_DMA_FRAG_REQ: fragment request mode
--
1.7.9.5


2018-04-19 02:03:39

by Baolin Wang

[permalink] [raw]
Subject: [PATCH v2 2/5] dmaengine: sprd: Define the DMA data width type

Define the DMA data width type to make code more readable.

Signed-off-by: Baolin Wang <[email protected]>
---
Changes since v1:
- No updates.
---
drivers/dma/sprd-dma.c | 14 +++++++++++---
1 file changed, 11 insertions(+), 3 deletions(-)

diff --git a/drivers/dma/sprd-dma.c b/drivers/dma/sprd-dma.c
index dcfa417..65ff0a58 100644
--- a/drivers/dma/sprd-dma.c
+++ b/drivers/dma/sprd-dma.c
@@ -176,6 +176,14 @@ enum sprd_dma_int_type {
SPRD_DMA_CFGERR_INT,
};

+/* dma data width values */
+enum sprd_dma_datawidth {
+ SPRD_DMA_DATAWIDTH_1_BYTE,
+ SPRD_DMA_DATAWIDTH_2_BYTES,
+ SPRD_DMA_DATAWIDTH_4_BYTES,
+ SPRD_DMA_DATAWIDTH_8_BYTES,
+};
+
/* dma channel hardware configuration */
struct sprd_dma_chn_hw {
u32 pause;
@@ -604,15 +612,15 @@ static int sprd_dma_config(struct dma_chan *chan, struct sprd_dma_desc *sdesc,
u32 fix_mode = 0, fix_en = 0;

if (IS_ALIGNED(len, 4)) {
- datawidth = 2;
+ datawidth = SPRD_DMA_DATAWIDTH_4_BYTES;
src_step = SPRD_DMA_WORD_STEP;
des_step = SPRD_DMA_WORD_STEP;
} else if (IS_ALIGNED(len, 2)) {
- datawidth = 1;
+ datawidth = SPRD_DMA_DATAWIDTH_2_BYTES;
src_step = SPRD_DMA_SHORT_STEP;
des_step = SPRD_DMA_SHORT_STEP;
} else {
- datawidth = 0;
+ datawidth = SPRD_DMA_DATAWIDTH_1_BYTE;
src_step = SPRD_DMA_BYTE_STEP;
des_step = SPRD_DMA_BYTE_STEP;
}
--
1.7.9.5


2018-04-19 02:04:15

by Baolin Wang

[permalink] [raw]
Subject: [PATCH v2 3/5] dmaengine: sprd: Move DMA request mode and interrupt type into head file

From: Eric Long <[email protected]>

This patch will move the Spreadtrum DMA request mode and interrupt type
into one head file for user to configure.

Signed-off-by: Eric Long <[email protected]>
Signed-off-by: Baolin Wang <[email protected]>
---
Changes since v1:
- No updates.
---
drivers/dma/sprd-dma.c | 52 +-------------------------------------
include/linux/dma/sprd-dma.h | 57 ++++++++++++++++++++++++++++++++++++++++++
2 files changed, 58 insertions(+), 51 deletions(-)
create mode 100644 include/linux/dma/sprd-dma.h

diff --git a/drivers/dma/sprd-dma.c b/drivers/dma/sprd-dma.c
index 65ff0a58..ccdeb8f 100644
--- a/drivers/dma/sprd-dma.c
+++ b/drivers/dma/sprd-dma.c
@@ -6,6 +6,7 @@

#include <linux/clk.h>
#include <linux/dma-mapping.h>
+#include <linux/dma/sprd-dma.h>
#include <linux/errno.h>
#include <linux/init.h>
#include <linux/interrupt.h>
@@ -125,57 +126,6 @@

#define SPRD_DMA_SOFTWARE_UID 0

-/*
- * enum sprd_dma_req_mode: define the DMA request mode
- * @SPRD_DMA_FRAG_REQ: fragment request mode
- * @SPRD_DMA_BLK_REQ: block request mode
- * @SPRD_DMA_TRANS_REQ: transaction request mode
- * @SPRD_DMA_LIST_REQ: link-list request mode
- *
- * We have 4 types request mode: fragment mode, block mode, transaction mode
- * and linklist mode. One transaction can contain several blocks, one block can
- * contain several fragments. Link-list mode means we can save several DMA
- * configuration into one reserved memory, then DMA can fetch each DMA
- * configuration automatically to start transfer.
- */
-enum sprd_dma_req_mode {
- SPRD_DMA_FRAG_REQ,
- SPRD_DMA_BLK_REQ,
- SPRD_DMA_TRANS_REQ,
- SPRD_DMA_LIST_REQ,
-};
-
-/*
- * enum sprd_dma_int_type: define the DMA interrupt type
- * @SPRD_DMA_NO_INT: do not need generate DMA interrupts.
- * @SPRD_DMA_FRAG_INT: fragment done interrupt when one fragment request
- * is done.
- * @SPRD_DMA_BLK_INT: block done interrupt when one block request is done.
- * @SPRD_DMA_BLK_FRAG_INT: block and fragment interrupt when one fragment
- * or one block request is done.
- * @SPRD_DMA_TRANS_INT: tansaction done interrupt when one transaction
- * request is done.
- * @SPRD_DMA_TRANS_FRAG_INT: transaction and fragment interrupt when one
- * transaction request or fragment request is done.
- * @SPRD_DMA_TRANS_BLK_INT: transaction and block interrupt when one
- * transaction request or block request is done.
- * @SPRD_DMA_LIST_INT: link-list done interrupt when one link-list request
- * is done.
- * @SPRD_DMA_CFGERR_INT: configure error interrupt when configuration is
- * incorrect.
- */
-enum sprd_dma_int_type {
- SPRD_DMA_NO_INT,
- SPRD_DMA_FRAG_INT,
- SPRD_DMA_BLK_INT,
- SPRD_DMA_BLK_FRAG_INT,
- SPRD_DMA_TRANS_INT,
- SPRD_DMA_TRANS_FRAG_INT,
- SPRD_DMA_TRANS_BLK_INT,
- SPRD_DMA_LIST_INT,
- SPRD_DMA_CFGERR_INT,
-};
-
/* dma data width values */
enum sprd_dma_datawidth {
SPRD_DMA_DATAWIDTH_1_BYTE,
diff --git a/include/linux/dma/sprd-dma.h b/include/linux/dma/sprd-dma.h
new file mode 100644
index 0000000..c545162
--- /dev/null
+++ b/include/linux/dma/sprd-dma.h
@@ -0,0 +1,57 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifndef _SPRD_DMA_H_
+#define _SPRD_DMA_H_
+
+/*
+ * enum sprd_dma_req_mode: define the DMA request mode
+ * @SPRD_DMA_FRAG_REQ: fragment request mode
+ * @SPRD_DMA_BLK_REQ: block request mode
+ * @SPRD_DMA_TRANS_REQ: transaction request mode
+ * @SPRD_DMA_LIST_REQ: link-list request mode
+ *
+ * We have 4 types request mode: fragment mode, block mode, transaction mode
+ * and linklist mode. One transaction can contain several blocks, one block can
+ * contain several fragments. Link-list mode means we can save several DMA
+ * configuration into one reserved memory, then DMA can fetch each DMA
+ * configuration automatically to start transfer.
+ */
+enum sprd_dma_req_mode {
+ SPRD_DMA_FRAG_REQ,
+ SPRD_DMA_BLK_REQ,
+ SPRD_DMA_TRANS_REQ,
+ SPRD_DMA_LIST_REQ,
+};
+
+/*
+ * enum sprd_dma_int_type: define the DMA interrupt type
+ * @SPRD_DMA_NO_INT: do not need generate DMA interrupts.
+ * @SPRD_DMA_FRAG_INT: fragment done interrupt when one fragment request
+ * is done.
+ * @SPRD_DMA_BLK_INT: block done interrupt when one block request is done.
+ * @SPRD_DMA_BLK_FRAG_INT: block and fragment interrupt when one fragment
+ * or one block request is done.
+ * @SPRD_DMA_TRANS_INT: tansaction done interrupt when one transaction
+ * request is done.
+ * @SPRD_DMA_TRANS_FRAG_INT: transaction and fragment interrupt when one
+ * transaction request or fragment request is done.
+ * @SPRD_DMA_TRANS_BLK_INT: transaction and block interrupt when one
+ * transaction request or block request is done.
+ * @SPRD_DMA_LIST_INT: link-list done interrupt when one link-list request
+ * is done.
+ * @SPRD_DMA_CFGERR_INT: configure error interrupt when configuration is
+ * incorrect.
+ */
+enum sprd_dma_int_type {
+ SPRD_DMA_NO_INT,
+ SPRD_DMA_FRAG_INT,
+ SPRD_DMA_BLK_INT,
+ SPRD_DMA_BLK_FRAG_INT,
+ SPRD_DMA_TRANS_INT,
+ SPRD_DMA_TRANS_FRAG_INT,
+ SPRD_DMA_TRANS_BLK_INT,
+ SPRD_DMA_LIST_INT,
+ SPRD_DMA_CFGERR_INT,
+};
+
+#endif
--
1.7.9.5


2018-04-27 06:20:59

by Vinod Koul

[permalink] [raw]
Subject: Re: [PATCH v2 4/5] dmaengine: sprd: Add Spreadtrum DMA configuration

On Thu, Apr 19, 2018 at 10:00:49AM +0800, Baolin Wang wrote:

> +/*
> + * struct sprd_dma_config - DMA configuration structure
> + * @src_addr: the physical address where DMA slave data should be read
> + * @dst_addr: the physical address where DMA slave data should be written
> + * @fragment_len: specify one fragment transfer length
> + * @block_len: specify one block transfer length
> + * @transcation_len: specify one transcation transfer length
> + * @src_step: source transfer step
> + * @dst_step: destination transfer step
> + * @src_datawidth: source transfer data width
> + * @dst_datawidth: destination transfer data width
> + * @wrap_ptr: wrap pointer address, once the transfer address reaches the
> + * 'wrap_ptr', the next transfer address will jump to the 'wrap_to' address.
> + * @wrap_to: wrap jump to address
> + * @req_mode: specify the DMA request mode
> + * @int_mode: specify the DMA interrupt type
> + * @slave_id: slave channel requester id
> + */
> +struct sprd_dma_config {

can you please not duplicate the dma_slave_config here. If you want to save
your own values then please embed dma_slave_config here
--
~Vinod

2018-04-27 06:21:57

by Vinod Koul

[permalink] [raw]
Subject: Re: [PATCH v2 1/5] dmaengine: sprd: Define the DMA transfer step type

On Thu, Apr 19, 2018 at 10:00:46AM +0800, Baolin Wang wrote:
> From: Eric Long <[email protected]>
>
> Define the DMA transfer step type to make code more readable.

Applied this one, thanks

--
~Vinod

2018-04-27 06:22:40

by Vinod Koul

[permalink] [raw]
Subject: Re: [PATCH v2 2/5] dmaengine: sprd: Define the DMA data width type

On Thu, Apr 19, 2018 at 10:00:47AM +0800, Baolin Wang wrote:
> Define the DMA data width type to make code more readable.

Applied this one, thanks
--
~Vinod

2018-04-27 06:23:15

by Vinod Koul

[permalink] [raw]
Subject: Re: [PATCH v2 3/5] dmaengine: sprd: Move DMA request mode and interrupt type into head file

On Thu, Apr 19, 2018 at 10:00:48AM +0800, Baolin Wang wrote:
> From: Eric Long <[email protected]>
>
> This patch will move the Spreadtrum DMA request mode and interrupt type
> into one head file for user to configure.

Applied this one, thanks
--
~Vinod

2018-04-30 08:18:39

by Baolin Wang

[permalink] [raw]
Subject: Re: [PATCH v2 4/5] dmaengine: sprd: Add Spreadtrum DMA configuration

Hi Vinod,

On 27 April 2018 at 14:24, Vinod Koul <[email protected]> wrote:
> On Thu, Apr 19, 2018 at 10:00:49AM +0800, Baolin Wang wrote:
>
>> +/*
>> + * struct sprd_dma_config - DMA configuration structure
>> + * @src_addr: the physical address where DMA slave data should be read
>> + * @dst_addr: the physical address where DMA slave data should be written
>> + * @fragment_len: specify one fragment transfer length
>> + * @block_len: specify one block transfer length
>> + * @transcation_len: specify one transcation transfer length
>> + * @src_step: source transfer step
>> + * @dst_step: destination transfer step
>> + * @src_datawidth: source transfer data width
>> + * @dst_datawidth: destination transfer data width
>> + * @wrap_ptr: wrap pointer address, once the transfer address reaches the
>> + * 'wrap_ptr', the next transfer address will jump to the 'wrap_to' address.
>> + * @wrap_to: wrap jump to address
>> + * @req_mode: specify the DMA request mode
>> + * @int_mode: specify the DMA interrupt type
>> + * @slave_id: slave channel requester id
>> + */
>> +struct sprd_dma_config {
>
> can you please not duplicate the dma_slave_config here. If you want to save
> your own values then please embed dma_slave_config here

Thanks for your suggestion. Will fix this in next version.

--
Baolin.wang
Best Regards