2018-06-05 01:21:53

by Dennis Gilmore

[permalink] [raw]
Subject: [PATCH] ARM: dts: armada388-helios4

The helios4 is a Armada388 based nas board designed by SolidRun and
based on their SOM. It is sold by kobol.io the dts file came from
https://raw.githubusercontent.com/armbian/build/master/patch/kernel/mvebu-default/95-helios4-device-tree.patch
I added a SPDX license line to match the clearfog it says it was based
on and a compatible line for "solidrun,helios4"

Signed-off-by: Dennis Gilmore <[email protected]>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/armada-388-helios4.dts | 315 +++++++++++++++++++++++
2 files changed, 316 insertions(+)
create mode 100644 arch/arm/boot/dts/armada-388-helios4.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 7e2424957809..490bfd586198 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1123,6 +1123,7 @@ dtb-$(CONFIG_MACH_ARMADA_38X) += \
armada-388-clearfog-pro.dtb \
armada-388-db.dtb \
armada-388-gp.dtb \
+ armada-388-helios4.dtb \
armada-388-rd.dtb
dtb-$(CONFIG_MACH_ARMADA_39X) += \
armada-398-db.dtb
diff --git a/arch/arm/boot/dts/armada-388-helios4.dts b/arch/arm/boot/dts/armada-388-helios4.dts
new file mode 100644
index 000000000000..a6d6996e1378
--- /dev/null
+++ b/arch/arm/boot/dts/armada-388-helios4.dts
@@ -0,0 +1,315 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Device Tree file for Helios4
+ * based on SolidRun Clearfog revision A1 rev 2.0 (88F6828)
+ *
+ * Copyright (C) 2017
+ *
+ */
+
+/dts-v1/;
+#include "armada-388.dtsi"
+#include "armada-38x-solidrun-microsom.dtsi"
+
+/ {
+ model = "Helios4";
+ compatible = "solidrun,helios4", "marvell,armada388",
+ "marvell,armada385", "marvell,armada380";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x80000000>; /* 2 GB */
+ };
+
+ aliases {
+ /* So that mvebu u-boot can update the MAC addresses */
+ ethernet1 = &eth0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ reg_12v: regulator-12v {
+ compatible = "regulator-fixed";
+ regulator-name = "power_brick_12V";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ vin-supply = <&reg_12v>;
+ };
+
+ reg_5p0v_hdd: regulator-5v-hdd {
+ compatible = "regulator-fixed";
+ regulator-name = "5V_HDD";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ vin-supply = <&reg_12v>;
+ };
+
+ reg_5p0v_usb: regulator-5v-usb {
+ compatible = "regulator-fixed";
+ regulator-name = "USB-PWR";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ enable-active-high;
+ gpio = <&expander0 6 GPIO_ACTIVE_HIGH>;
+ vin-supply = <&reg_12v>;
+ };
+
+ system-leds {
+ compatible = "gpio-leds";
+ status-led {
+ label = "helios4:green:status";
+ gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "heartbeat";
+ default-state = "on";
+ };
+
+ fault-led {
+ label = "helios4:red:fault";
+ gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ };
+ };
+
+ io-leds {
+ compatible = "gpio-leds";
+ sata1-led {
+ label = "helios4:green:ata1";
+ gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "ata1";
+ default-state = "off";
+ };
+ sata2-led {
+ label = "helios4:green:ata2";
+ gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "ata2";
+ default-state = "off";
+ };
+ sata3-led {
+ label = "helios4:green:ata3";
+ gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "ata3";
+ default-state = "off";
+ };
+ sata4-led {
+ label = "helios4:green:ata4";
+ gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "ata4";
+ default-state = "off";
+ };
+ usb-led {
+ label = "helios4:green:usb";
+ gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "usb-host";
+ default-state = "off";
+ };
+ };
+
+ fan1: j10-pwm {
+ compatible = "pwm-fan";
+ pwms = <&gpio1 9 40000>; /* Target freq:25 kHz */
+ };
+
+ fan2: j17-pwm {
+ compatible = "pwm-fan";
+ pwms = <&gpio1 23 40000>; /* Target freq:25 kHz */
+ };
+
+ usb2_phy: usb2-phy {
+ compatible = "usb-nop-xceiv";
+ vbus-regulator = <&reg_5p0v_usb>;
+ };
+
+ usb3_phy: usb3-phy {
+ compatible = "usb-nop-xceiv";
+ //vbus-regulator = <&reg_5p0v_usb>;
+ };
+
+ soc {
+ internal-regs {
+ i2c@11000 {
+ clock-frequency = <400000>;
+ pinctrl-0 = <&i2c0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ /*
+ * PCA9655 GPIO expander, up to 1MHz clock.
+ * 0-Board Revision bit 0 #
+ * 1-Board Revision bit 1 #
+ * 5-USB3 overcurrent
+ * 6-USB3 power
+ */
+ expander0: gpio-expander@20 {
+ /*
+ * This is how it should be:
+ * compatible = "onnn,pca9655",
+ * "nxp,pca9555";
+ * but you can't do this because of
+ * the way I2C works.
+ */
+ compatible = "nxp,pca9555";
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x20>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pca0_pins>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ board_rev_bit_0 {
+ gpio-hog;
+ gpios = <0 GPIO_ACTIVE_LOW>;
+ input;
+ line-name = "board-rev-0";
+ };
+ board_rev_bit_1 {
+ gpio-hog;
+ gpios = <1 GPIO_ACTIVE_LOW>;
+ input;
+ line-name = "board-rev-1";
+ };
+ usb3_ilimit {
+ gpio-hog;
+ gpios = <5 GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "usb-overcurrent-status";
+ };
+ };
+
+ temp_sensor: temp@4c {
+ compatible = "ti,lm75";
+ reg = <0x4c>;
+ vcc-supply = <&reg_3p3v>;
+ };
+ };
+
+ i2c@11100 {
+ /*
+ * External I2C Bus for user peripheral
+ */
+ clock-frequency = <400000>;
+ pinctrl-0 = <&helios_i2c1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+
+ sata@a8000 {
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ sata0: sata-port@0 {
+ reg = <0>;
+ };
+
+ sata1: sata-port@1 {
+ reg = <1>;
+ };
+ };
+
+ sata@e0000 {
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ sata2: sata-port@0 {
+ reg = <0>;
+ };
+
+ sata3: sata-port@1 {
+ reg = <1>;
+ };
+ };
+
+ spi@10680 {
+ pinctrl-0 = <&spi1_pins
+ &microsom_spi1_cs_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+
+ sdhci@d8000 {
+ bus-width = <4>;
+ cd-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ pinctrl-0 = <&helios_sdhci_pins
+ &helios_sdhci_cd_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ vmmc = <&reg_3p3v>;
+ wp-inverted;
+ };
+
+ usb@58000 {
+ //vcc-supply = <&reg_5p0v_usb>;
+ usb-phy = <&usb2_phy>;
+ status = "okay";
+ };
+
+ usb3@f0000 {
+ status = "okay";
+ };
+
+ usb3@f8000 {
+ status = "okay";
+ };
+
+ pinctrl@18000 {
+ pca0_pins: pca0-pins {
+ marvell,pins = "mpp23";
+ marvell,function = "gpio";
+ };
+ microsom_phy0_int_pins: microsom-phy0-int-pins {
+ marvell,pins = "mpp18";
+ marvell,function = "gpio";
+ };
+ helios_i2c1_pins: i2c1-pins {
+ marvell,pins = "mpp26", "mpp27";
+ marvell,function = "i2c1";
+ };
+ helios_sdhci_cd_pins: helios-sdhci-cd-pins {
+ marvell,pins = "mpp20";
+ marvell,function = "gpio";
+ };
+ helios_sdhci_pins: helios-sdhci-pins {
+ marvell,pins = "mpp21", "mpp28",
+ "mpp37", "mpp38",
+ "mpp39", "mpp40";
+ marvell,function = "sd0";
+ };
+ helios_led_pins: helios-led-pins {
+ marvell,pins = "mpp24", "mpp25",
+ "mpp49", "mpp50",
+ "mpp52", "mpp53",
+ "mpp54";
+ marvell,function = "gpio";
+ };
+ helios_fan_pins: helios-fan-pins {
+ marvell,pins = "mpp41", "mpp43",
+ "mpp48", "mpp55";
+ marvell,function = "gpio";
+ };
+ microsom_spi1_cs_pins: spi1-cs-pins {
+ marvell,pins = "mpp59";
+ marvell,function = "spi1";
+ };
+ };
+ };
+ };
+};
--
2.17.1



2018-06-05 02:56:46

by Baruch Siach

[permalink] [raw]
Subject: Re: [PATCH] ARM: dts: armada388-helios4

Hi Dennis,

On Mon, Jun 04, 2018 at 08:13:43PM -0500, Dennis Gilmore wrote:
> The helios4 is a Armada388 based nas board designed by SolidRun and
> based on their SOM. It is sold by kobol.io the dts file came from
> https://raw.githubusercontent.com/armbian/build/master/patch/kernel/mvebu-default/95-helios4-device-tree.patch
> I added a SPDX license line to match the clearfog it says it was based
> on and a compatible line for "solidrun,helios4"
>
> Signed-off-by: Dennis Gilmore <[email protected]>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/armada-388-helios4.dts | 315 +++++++++++++++++++++++
> 2 files changed, 316 insertions(+)
> create mode 100644 arch/arm/boot/dts/armada-388-helios4.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 7e2424957809..490bfd586198 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1123,6 +1123,7 @@ dtb-$(CONFIG_MACH_ARMADA_38X) += \
> armada-388-clearfog-pro.dtb \
> armada-388-db.dtb \
> armada-388-gp.dtb \
> + armada-388-helios4.dtb \
> armada-388-rd.dtb
> dtb-$(CONFIG_MACH_ARMADA_39X) += \
> armada-398-db.dtb
> diff --git a/arch/arm/boot/dts/armada-388-helios4.dts b/arch/arm/boot/dts/armada-388-helios4.dts
> new file mode 100644
> index 000000000000..a6d6996e1378
> --- /dev/null
> +++ b/arch/arm/boot/dts/armada-388-helios4.dts
> @@ -0,0 +1,315 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Device Tree file for Helios4
> + * based on SolidRun Clearfog revision A1 rev 2.0 (88F6828)
> + *
> + * Copyright (C) 2017
> + *
> + */
> +
> +/dts-v1/;
> +#include "armada-388.dtsi"
> +#include "armada-38x-solidrun-microsom.dtsi"
> +
> +/ {
> + model = "Helios4";
> + compatible = "solidrun,helios4", "marvell,armada388",

SolidRun is not the producer of the Helios4 carrier board. So I think
"kobol,helios4" makes more sense. This is just like the "auvidea,h100"
compatible string for Auvidea H100 which is also using a SolidRun SOM.

baruch

> + "marvell,armada385", "marvell,armada380";
> +

--
http://baruch.siach.name/blog/ ~. .~ Tk Open Systems
=}------------------------------------------------ooO--U--Ooo------------{=
- [email protected] - tel: +972.52.368.4656, http://www.tkos.co.il -