Both PHYs are 4-port PHY that are 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X
and triple-speed copper SFP capable, can communicate with the MAC via
SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking
pattern of each of its 4 LEDs, supports SyncE as well as HP Auto-MDIX
detection.
VSC8574 supports WOL and VSC8584 supports hardware offloading of MACsec.
This patch series add support for 10/100/1000BASE-T, SGMII/QSGMII link with
the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for
their 4 LEDs.
They have also an internal Intel 8051 microcontroller whose firmware needs
to be patched when the PHY is reset. If the 8051's firmware has the
expected CRC, its patching can be skipped. The microcontroller can be
accessed from any port of the PHY, though the CRC function can only be done
through the PHY that is the base PHY of the package (internal address 0)
due to a limitation of the firmware.
The GPIO register bank is a set of registers that are common to all PHYs in
the package. So any modification in any register of this bank affects all
PHYs of the package.
If the PHYs haven't been reset before booting the Linux kernel and were
configured to use interrupts for e.g. link status updates, it is required
to clear the interrupts mask register of all PHYs before being able to use
interrupts with any PHY. The first PHY of the package that will be init
will take care of clearing all PHYs interrupts mask registers. Thus, we
need to keep track of the init sequence in the package, if it's already
been done or if it's to be done.
Most of the init sequence of a PHY of the package is common to all PHYs in
the package, thus we use the SMI broadcast feature which enables us to
propagate a write in one register of one PHY to all PHYs in the same
package.
We also introduce a new development board called PCB120 which exists in
variants for VSC8584 and VSC8574 (and that's the only difference to the
best of my knowledge).
I suggest patches 1 to 3 go through net tree and patches 4 and 5 go
through MIPS tree. Patches going through net tree and those going through
MIPS tree do not depend on one another.
This patch series depends on two patch series though:
"mscc: ocelot: add support for SerDes muxing configuration"
(https://lore.kernel.org/lkml/[email protected]/)
"net: phy: mscc: various improvements to Microsemi PHY driver"
(https://lore.kernel.org/lkml/[email protected]/)
Thanks,
Quentin
v2:
- add reviewed-by,
- create phy_base_write/read functions to replace ugly
__mdiobus_write/read,
- add a base_addr variable in the priv structure of the phy driver to
store the MDIO address of the base PHY in the package,
- use this base_addr everywhere in the driver in lieu of passing the pair
(mii_bus, int phy_addr) to each function,
- add a mutex_is_locked() check in writes and read within the
config_init function,
- specify that broadcasting feature is impacting PHYs in the same package
only and not accross the whole MDIO bus,
- remove patch that introduced a config_pre_init function pointer to be
set in the probe function depending on the probed PHY and used in the
config_init function, instead, check the matched PHY in config_init to
call the appropriate config_pre_init function,
- migrate the multiple constants writes to an iteration over an array of
constants,
- move pinctrl DT node for PHY interrupt to the board DTS,
- rename the pinctrl DT from the obscure gpio4 to phy_int_pins,
Quentin Schulz (5):
dt-bindings: net: vsc8531: add two additional LED modes for VSC8584
net: phy: mscc: add support for VSC8584 PHY
net: phy: mscc: add support for VSC8574 PHY
MIPS: mscc: add DT for Ocelot PCB120
MIPS: mscc: add PCB120 to the ocelot fitImage
arch/mips/boot/dts/mscc/Makefile | 2 +-
arch/mips/boot/dts/mscc/ocelot_pcb120.dts | 107 ++
arch/mips/generic/Kconfig | 6 +-
arch/mips/generic/Platform | 2 +-
...ocelot_pcb123.its.S => board-ocelot.its.S} | 17 +
drivers/net/phy/mscc.c | 1065 +++++++++++++++++
include/dt-bindings/net/mscc-phy-vsc8531.h | 2 +
7 files changed, 1196 insertions(+), 5 deletions(-)
create mode 100644 arch/mips/boot/dts/mscc/ocelot_pcb120.dts
rename arch/mips/generic/{board-ocelot_pcb123.its.S => board-ocelot.its.S} (55%)
--
2.17.1
The VSC8574 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX,
1000BASE-X and triple-speed copper SFP capable, can communicate with
the MAC via SGMII, QSGMII or 1000BASE-X, supports WOL, downshifting and
can set the blinking pattern of each of its 4 LEDs, supports SyncE as
well as HP Auto-MDIX detection.
This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC,
WOL, downshifting, HP Auto-MDIX detection and blinking pattern for its 4
LEDs.
The VSC8574 has also an internal Intel 8051 microcontroller whose
firmware needs to be patched when the PHY is reset. If the 8051's
firmware has the expected CRC, its patching can be skipped. The
microcontroller can be accessed from any port of the PHY, though the CRC
function can only be done through the PHY that is the base PHY of the
package (internal address 0) due to a limitation of the firmware.
The GPIO register bank is a set of registers that are common to all PHYs
in the package. So any modification in any register of this bank affects
all PHYs of the package.
If the PHYs haven't been reset before booting the Linux kernel and were
configured to use interrupts for e.g. link status updates, it is
required to clear the interrupts mask register of all PHYs before being
able to use interrupts with any PHY. The first PHY of the package that
will be init will take care of clearing all PHYs interrupts mask
registers. Thus, we need to keep track of the init sequence in the
package, if it's already been done or if it's to be done.
Most of the init sequence of a PHY of the package is common to all PHYs
in the package, thus we use the SMI broadcast feature which enables us
to propagate a write in one register of one PHY to all PHYs in the same
package.
Signed-off-by: Quentin Schulz <[email protected]>
---
drivers/net/phy/mscc.c | 320 ++++++++++++++++++++++++++++++++++++++++-
1 file changed, 319 insertions(+), 1 deletion(-)
diff --git a/drivers/net/phy/mscc.c b/drivers/net/phy/mscc.c
index 14d61aac1313..0e1502dcc24c 100644
--- a/drivers/net/phy/mscc.c
+++ b/drivers/net/phy/mscc.c
@@ -65,6 +65,8 @@ enum rgmii_rx_clock_delay {
#define MEDIA_OP_MODE_AMS_COPPER_100BASEFX 7
#define MEDIA_OP_MODE_POS 8
+#define MSCC_PHY_EXT_PHY_CNTL_2 24
+
#define MII_VSC85XX_INT_MASK 25
#define MII_VSC85XX_INT_MASK_MASK 0xa000
#define MII_VSC85XX_INT_MASK_WOL 0x0040
@@ -151,6 +153,7 @@ enum rgmii_rx_clock_delay {
#define DW8051_CLK_EN 0x0010
#define MICRO_CLK_EN 0x0008
#define MICRO_CLK_DIVIDE(x) ((x) >> 1)
+#define MSCC_DW8051_VLD_MASK 0xf1ff
/* x Address in range 1-4 */
#define MSCC_TRAP_ROM_ADDR(x) ((x) * 2 + 1)
@@ -184,7 +187,9 @@ enum rgmii_rx_clock_delay {
#define PROC_CMD_SGMII_MAC 0x0030
#define PROC_CMD_QSGMII_MAC 0x0020
#define PROC_CMD_NO_MAC_CONF 0x0000
+#define PROC_CMD_1588_DEFAULT_INIT 0x0010
#define PROC_CMD_NOP 0x000f
+#define PROC_CMD_PHY_INIT 0x000a
#define PROC_CMD_CRC16 0x0008
#define PROC_CMD_FIBER_MEDIA_CONF 0x0001
#define PROC_CMD_MCB_ACCESS_MAC_CONF 0x0000
@@ -198,6 +203,9 @@ enum rgmii_rx_clock_delay {
/* Test page Registers */
#define MSCC_PHY_TEST_PAGE_5 5
#define MSCC_PHY_TEST_PAGE_8 8
+#define MSCC_PHY_TEST_PAGE_9 9
+#define MSCC_PHY_TEST_PAGE_20 20
+#define MSCC_PHY_TEST_PAGE_24 24
/* Token ring page Registers */
#define MSCC_PHY_TR_CNTL 16
@@ -211,6 +219,7 @@ enum rgmii_rx_clock_delay {
#define PHY_ID_VSC8531 0x00070570
#define PHY_ID_VSC8540 0x00070760
#define PHY_ID_VSC8541 0x00070770
+#define PHY_ID_VSC8574 0x000704a0
#define PHY_ID_VSC8584 0x000707c0
#define MSCC_VDDMAC_1500 1500
@@ -258,6 +267,10 @@ enum rgmii_rx_clock_delay {
#define MSCC_VSC8584_REVB_INT8051_FW_START_ADDR 0xe800
#define MSCC_VSC8584_REVB_INT8051_FW_CRC 0xfb48
+#define MSCC_VSC8574_REVB_INT8051_FW "mscc_vsc8574_revb_int8051_29e8.bin"
+#define MSCC_VSC8574_REVB_INT8051_FW_START_ADDR 0x4000
+#define MSCC_VSC8574_REVB_INT8051_FW_CRC 0x29e8
+
#define VSC8584_REVB 0x0001
#define MSCC_DEV_REV_MASK GENMASK(3, 0)
@@ -1133,6 +1146,250 @@ static int vsc8584_patch_fw(struct phy_device *phydev,
return 0;
}
+/* bus->mdio_lock should be locked when using this function */
+static bool vsc8574_is_serdes_init(struct phy_device *phydev)
+{
+ u16 reg;
+ bool ret;
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS,
+ MSCC_PHY_PAGE_EXTENDED_GPIO);
+
+ reg = phy_base_read(phydev, MSCC_TRAP_ROM_ADDR(1));
+ if (reg != 0x3eb7) {
+ ret = false;
+ goto out;
+ }
+
+ reg = phy_base_read(phydev, MSCC_PATCH_RAM_ADDR(1));
+ if (reg != 0x4012) {
+ ret = false;
+ goto out;
+ }
+
+ reg = phy_base_read(phydev, MSCC_INT_MEM_CNTL);
+ if (reg != EN_PATCH_RAM_TRAP_ADDR(1)) {
+ ret = false;
+ goto out;
+ }
+
+ reg = phy_base_read(phydev, MSCC_DW8051_CNTL_STATUS);
+ if ((MICRO_NSOFT_RESET | RUN_FROM_INT_ROM | DW8051_CLK_EN |
+ MICRO_CLK_EN) != (reg & MSCC_DW8051_VLD_MASK)) {
+ ret = false;
+ goto out;
+ }
+
+ ret = true;
+out:
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
+
+ return ret;
+}
+
+/* bus->mdio_lock should be locked when using this function */
+static int vsc8574_config_pre_init(struct phy_device *phydev)
+{
+ const struct reg_val pre_init1[] = {
+ {0x0fae, 0x000401bd},
+ {0x0fac, 0x000f000f},
+ {0x17a0, 0x00a0f147},
+ {0x0fe4, 0x00052f54},
+ {0x1792, 0x0027303d},
+ {0x07fe, 0x00000704},
+ {0x0fe0, 0x00060150},
+ {0x0f82, 0x0012b00a},
+ {0x0f80, 0x00000d74},
+ {0x02e0, 0x00000012},
+ {0x03a2, 0x00050208},
+ {0x03b2, 0x00009186},
+ {0x0fb0, 0x000e3700},
+ {0x1688, 0x00049f81},
+ {0x0fd2, 0x0000ffff},
+ {0x168a, 0x00039fa2},
+ {0x1690, 0x0020640b},
+ {0x0258, 0x00002220},
+ {0x025a, 0x00002a20},
+ {0x025c, 0x00003060},
+ {0x025e, 0x00003fa0},
+ {0x03a6, 0x0000e0f0},
+ {0x0f92, 0x00001489},
+ {0x16a2, 0x00007000},
+ {0x16a6, 0x00071448},
+ {0x16a0, 0x00eeffdd},
+ {0x0fe8, 0x0091b06c},
+ {0x0fea, 0x00041600},
+ {0x16b0, 0x00eeff00},
+ {0x16b2, 0x00007000},
+ {0x16b4, 0x00000814},
+ {0x0f90, 0x00688980},
+ {0x03a4, 0x0000d8f0},
+ {0x0fc0, 0x00000400},
+ {0x07fa, 0x0050100f},
+ {0x0796, 0x00000003},
+ {0x07f8, 0x00c3ff98},
+ {0x0fa4, 0x0018292a},
+ {0x168c, 0x00d2c46f},
+ {0x17a2, 0x00000620},
+ {0x16a4, 0x0013132f},
+ {0x16a8, 0x00000000},
+ {0x0ffc, 0x00c0a028},
+ {0x0fec, 0x00901c09},
+ {0x0fee, 0x0004a6a1},
+ {0x0ffe, 0x00b01807},
+ };
+ const struct reg_val pre_init2[] = {
+ {0x0486, 0x0008a518},
+ {0x0488, 0x006dc696},
+ {0x048a, 0x00000912},
+ {0x048e, 0x00000db6},
+ {0x049c, 0x00596596},
+ {0x049e, 0x00000514},
+ {0x04a2, 0x00410280},
+ {0x04a4, 0x00000000},
+ {0x04a6, 0x00000000},
+ {0x04a8, 0x00000000},
+ {0x04aa, 0x00000000},
+ {0x04ae, 0x007df7dd},
+ {0x04b0, 0x006d95d4},
+ {0x04b2, 0x00492410},
+ };
+ struct device *dev = &phydev->mdio.dev;
+ const struct firmware *fw;
+ unsigned int i;
+ u16 crc, reg;
+ bool serdes_init;
+ int ret;
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
+
+ /* all writes below are broadcasted to all PHYs in the same package */
+ reg = phy_base_read(phydev, MSCC_PHY_EXT_CNTL_STATUS);
+ reg |= SMI_BROADCAST_WR_EN;
+ phy_base_write(phydev, MSCC_PHY_EXT_CNTL_STATUS, reg);
+
+ phy_base_write(phydev, MII_VSC85XX_INT_MASK, 0);
+
+ /* The below register writes are tweaking analog and electrical
+ * configuration that were determined through characterization by PHY
+ * engineers. These don't mean anything more than "these are the best
+ * values".
+ */
+ phy_base_write(phydev, MSCC_PHY_EXT_PHY_CNTL_2, 0x0040);
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_TEST);
+
+ phy_base_write(phydev, MSCC_PHY_TEST_PAGE_20, 0x4320);
+ phy_base_write(phydev, MSCC_PHY_TEST_PAGE_24, 0x0c00);
+ phy_base_write(phydev, MSCC_PHY_TEST_PAGE_9, 0x18ca);
+ phy_base_write(phydev, MSCC_PHY_TEST_PAGE_5, 0x1b20);
+
+ reg = phy_base_read(phydev, MSCC_PHY_TEST_PAGE_8);
+ reg |= 0x8000;
+ phy_base_write(phydev, MSCC_PHY_TEST_PAGE_8, reg);
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_TR);
+
+ for (i = 0; i < ARRAY_SIZE(pre_init1); i++)
+ vsc8584_csr_write(phydev, pre_init1[i].reg, pre_init1[i].val);
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_EXTENDED_2);
+
+ phy_base_write(phydev, MSCC_PHY_CU_PMD_TX_CNTL, 0x028e);
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_TR);
+
+ for (i = 0; i < ARRAY_SIZE(pre_init2); i++)
+ vsc8584_csr_write(phydev, pre_init2[i].reg, pre_init2[i].val);
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_TEST);
+
+ reg = phy_base_read(phydev, MSCC_PHY_TEST_PAGE_8);
+ reg &= ~0x8000;
+ phy_base_write(phydev, MSCC_PHY_TEST_PAGE_8, reg);
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
+
+ /* end of write broadcasting */
+ reg = phy_base_read(phydev, MSCC_PHY_EXT_CNTL_STATUS);
+ reg &= ~SMI_BROADCAST_WR_EN;
+ phy_base_write(phydev, MSCC_PHY_EXT_CNTL_STATUS, reg);
+
+ ret = request_firmware(&fw, MSCC_VSC8574_REVB_INT8051_FW, dev);
+ if (ret) {
+ dev_err(dev, "failed to load firmware %s, ret: %d\n",
+ MSCC_VSC8574_REVB_INT8051_FW, ret);
+ return ret;
+ }
+
+ /* Add one byte to size for the one added by the patch_fw function */
+ ret = vsc8584_get_fw_crc(phydev,
+ MSCC_VSC8574_REVB_INT8051_FW_START_ADDR,
+ fw->size + 1, &crc);
+ if (ret)
+ goto out;
+
+ if (crc == MSCC_VSC8574_REVB_INT8051_FW_CRC) {
+ serdes_init = vsc8574_is_serdes_init(phydev);
+
+ if (!serdes_init) {
+ ret = vsc8584_micro_assert_reset(phydev);
+ if (ret) {
+ dev_err(dev,
+ "%s: failed to assert reset of micro\n",
+ __func__);
+ return ret;
+ }
+ }
+ } else {
+ dev_dbg(dev, "FW CRC is not the expected one, patching FW\n");
+
+ serdes_init = false;
+
+ if (vsc8584_patch_fw(phydev, fw))
+ dev_warn(dev,
+ "failed to patch FW, expect non-optimal device\n");
+ }
+
+ if (!serdes_init) {
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS,
+ MSCC_PHY_PAGE_EXTENDED_GPIO);
+
+ phy_base_write(phydev, MSCC_TRAP_ROM_ADDR(1), 0x3eb7);
+ phy_base_write(phydev, MSCC_PATCH_RAM_ADDR(1), 0x4012);
+ phy_base_write(phydev, MSCC_INT_MEM_CNTL,
+ EN_PATCH_RAM_TRAP_ADDR(1));
+
+ vsc8584_micro_deassert_reset(phydev, false);
+
+ /* Add one byte to size for the one added by the patch_fw
+ * function
+ */
+ ret = vsc8584_get_fw_crc(phydev,
+ MSCC_VSC8574_REVB_INT8051_FW_START_ADDR,
+ fw->size + 1, &crc);
+ if (ret)
+ goto out;
+
+ if (crc != MSCC_VSC8574_REVB_INT8051_FW_CRC)
+ dev_warn(dev,
+ "FW CRC after patching is not the expected one, expect non-optimal device\n");
+ }
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS,
+ MSCC_PHY_PAGE_EXTENDED_GPIO);
+
+ ret = vsc8584_cmd(phydev, PROC_CMD_1588_DEFAULT_INIT |
+ PROC_CMD_PHY_INIT);
+
+out:
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
+
+ release_firmware(fw);
+
+ return ret;
+}
+
/* bus->mdio_lock should be locked when using this function */
static int vsc8584_config_pre_init(struct phy_device *phydev)
{
@@ -1356,7 +1613,15 @@ static int vsc8584_config_init(struct phy_device *phydev)
* in this pre-init function.
*/
if (!vsc8584_is_pkg_init(phydev, val & PHY_ADDR_REVERSED ? 1 : 0)) {
- ret = vsc8584_config_pre_init(phydev);
+ if ((phydev->phy_id & phydev->drv->phy_id_mask) ==
+ (PHY_ID_VSC8574 & phydev->drv->phy_id_mask))
+ ret = vsc8574_config_pre_init(phydev);
+ else if ((phydev->phy_id & phydev->drv->phy_id_mask) ==
+ (PHY_ID_VSC8584 & phydev->drv->phy_id_mask))
+ ret = vsc8584_config_pre_init(phydev);
+ else
+ ret = -EINVAL;
+
if (ret)
goto err;
}
@@ -1522,6 +1787,31 @@ static int vsc85xx_read_status(struct phy_device *phydev)
return genphy_read_status(phydev);
}
+static int vsc8574_probe(struct phy_device *phydev)
+{
+ struct vsc8531_private *vsc8531;
+ u32 default_mode[4] = {VSC8531_LINK_1000_ACTIVITY,
+ VSC8531_LINK_100_ACTIVITY, VSC8531_LINK_ACTIVITY,
+ VSC8531_DUPLEX_COLLISION};
+
+ vsc8531 = devm_kzalloc(&phydev->mdio.dev, sizeof(*vsc8531), GFP_KERNEL);
+ if (!vsc8531)
+ return -ENOMEM;
+
+ phydev->priv = vsc8531;
+
+ vsc8531->nleds = 4;
+ vsc8531->supp_led_modes = VSC8584_SUPP_LED_MODES;
+ vsc8531->hw_stats = vsc8584_hw_stats;
+ vsc8531->nstats = ARRAY_SIZE(vsc8584_hw_stats);
+ vsc8531->stats = devm_kmalloc_array(&phydev->mdio.dev, vsc8531->nstats,
+ sizeof(u64), GFP_KERNEL);
+ if (!vsc8531->stats)
+ return -ENOMEM;
+
+ return vsc85xx_dt_led_modes_get(phydev, default_mode);
+}
+
static int vsc8584_probe(struct phy_device *phydev)
{
struct vsc8531_private *vsc8531;
@@ -1688,6 +1978,33 @@ static struct phy_driver vsc85xx_driver[] = {
.get_strings = &vsc85xx_get_strings,
.get_stats = &vsc85xx_get_stats,
},
+{
+ .phy_id = PHY_ID_VSC8574,
+ .name = "Microsemi GE VSC8574 SyncE",
+ .phy_id_mask = 0xfffffff0,
+ .features = PHY_GBIT_FEATURES,
+ .flags = PHY_HAS_INTERRUPT,
+ .soft_reset = &genphy_soft_reset,
+ .config_init = &vsc8584_config_init,
+ .config_aneg = &vsc85xx_config_aneg,
+ .aneg_done = &genphy_aneg_done,
+ .read_status = &vsc85xx_read_status,
+ .ack_interrupt = &vsc85xx_ack_interrupt,
+ .config_intr = &vsc85xx_config_intr,
+ .did_interrupt = &vsc8584_did_interrupt,
+ .suspend = &genphy_suspend,
+ .resume = &genphy_resume,
+ .probe = &vsc8574_probe,
+ .set_wol = &vsc85xx_wol_set,
+ .get_wol = &vsc85xx_wol_get,
+ .get_tunable = &vsc85xx_get_tunable,
+ .set_tunable = &vsc85xx_set_tunable,
+ .read_page = &vsc85xx_phy_read_page,
+ .write_page = &vsc85xx_phy_write_page,
+ .get_sset_count = &vsc85xx_get_sset_count,
+ .get_strings = &vsc85xx_get_strings,
+ .get_stats = &vsc85xx_get_stats,
+},
{
.phy_id = PHY_ID_VSC8584,
.name = "Microsemi GE VSC8584 SyncE",
@@ -1723,6 +2040,7 @@ static struct mdio_device_id __maybe_unused vsc85xx_tbl[] = {
{ PHY_ID_VSC8531, 0xfffffff0, },
{ PHY_ID_VSC8540, 0xfffffff0, },
{ PHY_ID_VSC8541, 0xfffffff0, },
+ { PHY_ID_VSC8574, 0xfffffff0, },
{ PHY_ID_VSC8584, 0xfffffff0, },
{ }
};
--
2.17.1
The Ocelot PCB120 evaluation board is different from the PCB123 in that
it has 4 external VSC8584 (or VSC8574) PHYs.
It uses the SoC's second MDIO bus for external PHYs which have a
reversed address on the bus (i.e. PHY4 is on address 3, PHY5 is on
address 2, PHY6 on 1 and PHY7 on 0).
Here is how the PHYs are connected to the switch ports:
port 0: phy0 (internal)
port 1: phy1 (internal)
port 2: phy2 (internal)
port 3: phy3 (internal)
port 4: phy7
port 5: phy4
port 6: phy6
port 9: phy5
Reviewed-by: Alexandre Belloni <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
---
arch/mips/boot/dts/mscc/Makefile | 2 +-
arch/mips/boot/dts/mscc/ocelot_pcb120.dts | 107 ++++++++++++++++++++++
2 files changed, 108 insertions(+), 1 deletion(-)
create mode 100644 arch/mips/boot/dts/mscc/ocelot_pcb120.dts
diff --git a/arch/mips/boot/dts/mscc/Makefile b/arch/mips/boot/dts/mscc/Makefile
index 9a9bb7ea0503..ec6f5b2bf093 100644
--- a/arch/mips/boot/dts/mscc/Makefile
+++ b/arch/mips/boot/dts/mscc/Makefile
@@ -1,3 +1,3 @@
-dtb-$(CONFIG_MSCC_OCELOT) += ocelot_pcb123.dtb
+dtb-$(CONFIG_MSCC_OCELOT) += ocelot_pcb123.dtb ocelot_pcb120.dtb
obj-$(CONFIG_BUILTIN_DTB) += $(addsuffix .o, $(dtb-y))
diff --git a/arch/mips/boot/dts/mscc/ocelot_pcb120.dts b/arch/mips/boot/dts/mscc/ocelot_pcb120.dts
new file mode 100644
index 000000000000..33991fd209f5
--- /dev/null
+++ b/arch/mips/boot/dts/mscc/ocelot_pcb120.dts
@@ -0,0 +1,107 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/* Copyright (c) 2017 Microsemi Corporation */
+
+/dts-v1/;
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/phy/phy-ocelot-serdes.h>
+#include "ocelot.dtsi"
+
+/ {
+ compatible = "mscc,ocelot-pcb120", "mscc,ocelot";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0e000000>;
+ };
+};
+
+&gpio {
+ phy_int_pins: phy_int_pins {
+ pins = "GPIO_4";
+ function = "gpio";
+ };
+};
+
+&mdio0 {
+ status = "okay";
+};
+
+&mdio1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&miim1>, <&phy_int_pins>;
+
+ phy7: ethernet-phy@0 {
+ reg = <0>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-parent = <&gpio>;
+ };
+ phy6: ethernet-phy@1 {
+ reg = <1>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-parent = <&gpio>;
+ };
+ phy5: ethernet-phy@2 {
+ reg = <2>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-parent = <&gpio>;
+ };
+ phy4: ethernet-phy@3 {
+ reg = <3>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-parent = <&gpio>;
+ };
+};
+
+&port0 {
+ phy-handle = <&phy0>;
+};
+
+&port1 {
+ phy-handle = <&phy1>;
+};
+
+&port2 {
+ phy-handle = <&phy2>;
+};
+
+&port3 {
+ phy-handle = <&phy3>;
+};
+
+&port4 {
+ phy-handle = <&phy7>;
+ phy-mode = "sgmii";
+ phys = <&serdes 4 SERDES1G(2)>;
+};
+
+&port5 {
+ phy-handle = <&phy4>;
+ phy-mode = "sgmii";
+ phys = <&serdes 5 SERDES1G(5)>;
+};
+
+&port6 {
+ phy-handle = <&phy6>;
+ phy-mode = "sgmii";
+ phys = <&serdes 6 SERDES1G(3)>;
+};
+
+&port9 {
+ phy-handle = <&phy5>;
+ phy-mode = "sgmii";
+ phys = <&serdes 9 SERDES1G(4)>;
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
--
2.17.1
PCB120 and PCB123 are both development boards based on Microsemi Ocelot
so let's use the same fitImage for both.
Reviewed-by: Alexandre Belloni <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
---
arch/mips/generic/Kconfig | 6 +++---
arch/mips/generic/Platform | 2 +-
...d-ocelot_pcb123.its.S => board-ocelot.its.S} | 17 +++++++++++++++++
3 files changed, 21 insertions(+), 4 deletions(-)
rename arch/mips/generic/{board-ocelot_pcb123.its.S => board-ocelot.its.S} (55%)
diff --git a/arch/mips/generic/Kconfig b/arch/mips/generic/Kconfig
index 08e33c6b2539..fd6019802657 100644
--- a/arch/mips/generic/Kconfig
+++ b/arch/mips/generic/Kconfig
@@ -65,11 +65,11 @@ config FIT_IMAGE_FDT_XILFPGA
Enable this to include the FDT for the MIPSfpga platform
from Imagination Technologies in the FIT kernel image.
-config FIT_IMAGE_FDT_OCELOT_PCB123
- bool "Include FDT for Microsemi Ocelot PCB123"
+config FIT_IMAGE_FDT_OCELOT
+ bool "Include FDT for Microsemi Ocelot development platforms"
select MSCC_OCELOT
help
- Enable this to include the FDT for the Ocelot PCB123 platform
+ Enable this to include the FDT for the Ocelot development platforms
from Microsemi in the FIT kernel image.
This requires u-boot on the platform.
diff --git a/arch/mips/generic/Platform b/arch/mips/generic/Platform
index 879cb80396c8..eaa19d189324 100644
--- a/arch/mips/generic/Platform
+++ b/arch/mips/generic/Platform
@@ -16,5 +16,5 @@ all-$(CONFIG_MIPS_GENERIC) := vmlinux.gz.itb
its-y := vmlinux.its.S
its-$(CONFIG_FIT_IMAGE_FDT_BOSTON) += board-boston.its.S
its-$(CONFIG_FIT_IMAGE_FDT_NI169445) += board-ni169445.its.S
-its-$(CONFIG_FIT_IMAGE_FDT_OCELOT_PCB123) += board-ocelot_pcb123.its.S
+its-$(CONFIG_FIT_IMAGE_FDT_OCELOT) += board-ocelot.its.S
its-$(CONFIG_FIT_IMAGE_FDT_XILFPGA) += board-xilfpga.its.S
diff --git a/arch/mips/generic/board-ocelot_pcb123.its.S b/arch/mips/generic/board-ocelot.its.S
similarity index 55%
rename from arch/mips/generic/board-ocelot_pcb123.its.S
rename to arch/mips/generic/board-ocelot.its.S
index 5a7d5e1c878a..3da23988149a 100644
--- a/arch/mips/generic/board-ocelot_pcb123.its.S
+++ b/arch/mips/generic/board-ocelot.its.S
@@ -11,6 +11,17 @@
algo = "sha1";
};
};
+
+ fdt@ocelot_pcb120 {
+ description = "MSCC Ocelot PCB120 Device Tree";
+ data = /incbin/("boot/dts/mscc/ocelot_pcb120.dtb");
+ type = "flat_dt";
+ arch = "mips";
+ compression = "none";
+ hash@0 {
+ algo = "sha1";
+ };
+ };
};
configurations {
@@ -19,5 +30,11 @@
kernel = "kernel@0";
fdt = "fdt@ocelot_pcb123";
};
+
+ conf@ocelot_pcb120 {
+ description = "Ocelot Linux kernel";
+ kernel = "kernel@0";
+ fdt = "fdt@ocelot_pcb120";
+ };
};
};
--
2.17.1
The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX,
1000BASE-X and triple-speed copper SFP capable, can communicate with the
MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set
the blinking pattern of each of its 4 LEDs, supports hardware offloading
of MACsec and supports SyncE as well as HP Auto-MDIX detection.
This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC,
downshifting, HP Auto-MDIX detection and blinking pattern for its 4
LEDs.
The VSC8584 has also an internal Intel 8051 microcontroller whose
firmware needs to be patched when the PHY is reset. If the 8051's
firmware has the expected CRC, its patching can be skipped. The
microcontroller can be accessed from any port of the PHY, though the CRC
function can only be done through the PHY that is the base PHY of the
package (internal address 0) due to a limitation of the firmware.
The GPIO register bank is a set of registers that are common to all PHYs
in the package. So any modification in any register of this bank affects
all PHYs of the package.
If the PHYs haven't been reset before booting the Linux kernel and were
configured to use interrupts for e.g. link status updates, it is
required to clear the interrupts mask register of all PHYs before being
able to use interrupts with any PHY. The first PHY of the package that
will be init will take care of clearing all PHYs interrupts mask
registers. Thus, we need to keep track of the init sequence in the
package, if it's already been done or if it's to be done.
Most of the init sequence of a PHY of the package is common to all PHYs
in the package, thus we use the SMI broadcast feature which enables us
to propagate a write in one register of one PHY to all PHYs in the same
package.
The revA of the VSC8584 PHY (which is not and will not be publicly
released) should NOT patch the firmware of the microcontroller or it'll
make things worse, the easiest way is just to not support it.
Signed-off-by: Quentin Schulz <[email protected]>
---
drivers/net/phy/mscc.c | 747 +++++++++++++++++++++++++++++++++++++++++
1 file changed, 747 insertions(+)
diff --git a/drivers/net/phy/mscc.c b/drivers/net/phy/mscc.c
index 9c7159e1ae17..14d61aac1313 100644
--- a/drivers/net/phy/mscc.c
+++ b/drivers/net/phy/mscc.c
@@ -6,6 +6,8 @@
* Copyright (c) 2016 Microsemi Corporation
*/
+#include <linux/firmware.h>
+#include <linux/jiffies.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/mdio.h>
@@ -32,6 +34,10 @@ enum rgmii_rx_clock_delay {
#define DISABLE_HP_AUTO_MDIX_MASK 0x0080
#define DISABLE_PAIR_SWAP_CORR_MASK 0x0020
#define DISABLE_POLARITY_CORR_MASK 0x0010
+#define PARALLEL_DET_IGNORE_ADVERTISED 0x0008
+
+#define MSCC_PHY_EXT_CNTL_STATUS 22
+#define SMI_BROADCAST_WR_EN 0x0001
#define MSCC_PHY_ERR_RX_CNT 19
#define MSCC_PHY_ERR_FALSE_CARRIER_CNT 20
@@ -44,7 +50,20 @@ enum rgmii_rx_clock_delay {
#define MAC_IF_SELECTION_RMII 1
#define MAC_IF_SELECTION_RGMII 2
#define MAC_IF_SELECTION_POS 11
+#define VSC8584_MAC_IF_SELECTION_MASK 0x1000
+#define VSC8584_MAC_IF_SELECTION_SGMII 0
+#define VSC8584_MAC_IF_SELECTION_1000BASEX 1
+#define VSC8584_MAC_IF_SELECTION_POS 12
#define FAR_END_LOOPBACK_MODE_MASK 0x0008
+#define MEDIA_OP_MODE_MASK 0x0700
+#define MEDIA_OP_MODE_COPPER 0
+#define MEDIA_OP_MODE_SERDES 1
+#define MEDIA_OP_MODE_1000BASEX 2
+#define MEDIA_OP_MODE_100BASEFX 3
+#define MEDIA_OP_MODE_AMS_COPPER_SERDES 5
+#define MEDIA_OP_MODE_AMS_COPPER_1000BASEX 6
+#define MEDIA_OP_MODE_AMS_COPPER_100BASEFX 7
+#define MEDIA_OP_MODE_POS 8
#define MII_VSC85XX_INT_MASK 25
#define MII_VSC85XX_INT_MASK_MASK 0xa000
@@ -67,6 +86,13 @@ enum rgmii_rx_clock_delay {
#define MSCC_PHY_PAGE_STANDARD 0x0000 /* Standard registers */
#define MSCC_PHY_PAGE_EXTENDED 0x0001 /* Extended registers */
#define MSCC_PHY_PAGE_EXTENDED_2 0x0002 /* Extended reg - page 2 */
+#define MSCC_PHY_PAGE_EXTENDED_3 0x0003 /* Extended reg - page 3 */
+#define MSCC_PHY_PAGE_EXTENDED_4 0x0004 /* Extended reg - page 4 */
+/* Extended reg - GPIO; this is a bank of registers that are shared for all PHYs
+ * in the same package.
+ */
+#define MSCC_PHY_PAGE_EXTENDED_GPIO 0x0010 /* Extended reg - GPIO */
+#define MSCC_PHY_PAGE_TEST 0x2a30 /* Test reg */
#define MSCC_PHY_PAGE_TR 0x52b5 /* Token ring registers */
/* Extended Page 1 Registers */
@@ -79,13 +105,21 @@ enum rgmii_rx_clock_delay {
#define FORCE_MDI_CROSSOVER_MDI 0x0008
#define MSCC_PHY_ACTIPHY_CNTL 20
+#define PHY_ADDR_REVERSED 0x0200
#define DOWNSHIFT_CNTL_MASK 0x001C
#define DOWNSHIFT_EN 0x0010
#define DOWNSHIFT_CNTL_POS 2
#define MSCC_PHY_EXT_PHY_CNTL_4 23
+#define PHY_CNTL_4_ADDR_POS 11
+
+#define MSCC_PHY_VERIPHY_CNTL_2 25
+
+#define MSCC_PHY_VERIPHY_CNTL_3 26
/* Extended Page 2 Registers */
+#define MSCC_PHY_CU_PMD_TX_CNTL 16
+
#define MSCC_PHY_RGMII_CNTL 20
#define RGMII_RX_CLK_DELAY_MASK 0x0070
#define RGMII_RX_CLK_DELAY_POS 4
@@ -101,6 +135,70 @@ enum rgmii_rx_clock_delay {
#define SECURE_ON_ENABLE 0x8000
#define SECURE_ON_PASSWD_LEN_4 0x4000
+/* Extended Page 3 Registers */
+#define MSCC_PHY_SERDES_TX_VALID_CNT 21
+#define MSCC_PHY_SERDES_TX_CRC_ERR_CNT 22
+#define MSCC_PHY_SERDES_RX_VALID_CNT 28
+#define MSCC_PHY_SERDES_RX_CRC_ERR_CNT 29
+
+/* Extended page GPIO Registers */
+#define MSCC_DW8051_CNTL_STATUS 0
+#define MICRO_NSOFT_RESET 0x8000
+#define RUN_FROM_INT_ROM 0x4000
+#define AUTOINC_ADDR 0x2000
+#define PATCH_RAM_CLK 0x1000
+#define MICRO_PATCH_EN 0x0080
+#define DW8051_CLK_EN 0x0010
+#define MICRO_CLK_EN 0x0008
+#define MICRO_CLK_DIVIDE(x) ((x) >> 1)
+
+/* x Address in range 1-4 */
+#define MSCC_TRAP_ROM_ADDR(x) ((x) * 2 + 1)
+#define MSCC_PATCH_RAM_ADDR(x) (((x) + 1) * 2)
+#define MSCC_INT_MEM_ADDR 11
+
+#define MSCC_INT_MEM_CNTL 12
+#define READ_SFR 0x6000
+#define READ_PRAM 0x4000
+#define READ_ROM 0x2000
+#define READ_RAM 0x0000
+#define INT_MEM_WRITE_EN 0x1000
+#define EN_PATCH_RAM_TRAP_ADDR(x) (0x0100 << ((x) - 1))
+#define INT_MEM_DATA_M 0x00ff
+#define INT_MEM_DATA(x) (INT_MEM_DATA_M & (x))
+
+#define MSCC_PHY_PROC_CMD 18
+#define PROC_CMD_NCOMPLETED 0x8000
+#define PROC_CMD_FAILED 0x4000
+#define PROC_CMD_SGMII_PORT(x) ((x) << 8)
+#define PROC_CMD_FIBER_PORT(x) (0x0100 << (x) % 4)
+#define PROC_CMD_QSGMII_PORT 0x0c00
+#define PROC_CMD_RST_CONF_PORT 0x0080
+#define PROC_CMD_RECONF_PORT 0x0000
+#define PROC_CMD_READ_MOD_WRITE_PORT 0x0040
+#define PROC_CMD_WRITE 0x0040
+#define PROC_CMD_READ 0x0000
+#define PROC_CMD_FIBER_DISABLE 0x0020
+#define PROC_CMD_FIBER_100BASE_FX 0x0010
+#define PROC_CMD_FIBER_1000BASE_X 0x0000
+#define PROC_CMD_SGMII_MAC 0x0030
+#define PROC_CMD_QSGMII_MAC 0x0020
+#define PROC_CMD_NO_MAC_CONF 0x0000
+#define PROC_CMD_NOP 0x000f
+#define PROC_CMD_CRC16 0x0008
+#define PROC_CMD_FIBER_MEDIA_CONF 0x0001
+#define PROC_CMD_MCB_ACCESS_MAC_CONF 0x0000
+#define PROC_CMD_NCOMPLETED_TIMEOUT_MS 500
+
+#define MSCC_PHY_MAC_CFG_FASTLINK 19
+#define MAC_CFG_MASK 0xc000
+#define MAC_CFG_SGMII 0x0000
+#define MAC_CFG_QSGMII 0x4000
+
+/* Test page Registers */
+#define MSCC_PHY_TEST_PAGE_5 5
+#define MSCC_PHY_TEST_PAGE_8 8
+
/* Token ring page Registers */
#define MSCC_PHY_TR_CNTL 16
#define TR_WRITE 0x8000
@@ -113,6 +211,7 @@ enum rgmii_rx_clock_delay {
#define PHY_ID_VSC8531 0x00070570
#define PHY_ID_VSC8540 0x00070760
#define PHY_ID_VSC8541 0x00070770
+#define PHY_ID_VSC8584 0x000707c0
#define MSCC_VDDMAC_1500 1500
#define MSCC_VDDMAC_1800 1800
@@ -122,6 +221,24 @@ enum rgmii_rx_clock_delay {
#define DOWNSHIFT_COUNT_MAX 5
#define MAX_LEDS 4
+
+#define VSC8584_SUPP_LED_MODES (BIT(VSC8531_LINK_ACTIVITY) | \
+ BIT(VSC8531_LINK_1000_ACTIVITY) | \
+ BIT(VSC8531_LINK_100_ACTIVITY) | \
+ BIT(VSC8531_LINK_10_ACTIVITY) | \
+ BIT(VSC8531_LINK_100_1000_ACTIVITY) | \
+ BIT(VSC8531_LINK_10_1000_ACTIVITY) | \
+ BIT(VSC8531_LINK_10_100_ACTIVITY) | \
+ BIT(VSC8584_LINK_100FX_1000X_ACTIVITY) | \
+ BIT(VSC8531_DUPLEX_COLLISION) | \
+ BIT(VSC8531_COLLISION) | \
+ BIT(VSC8531_ACTIVITY) | \
+ BIT(VSC8584_100FX_1000X_ACTIVITY) | \
+ BIT(VSC8531_AUTONEG_FAULT) | \
+ BIT(VSC8531_SERIAL_MODE) | \
+ BIT(VSC8531_FORCE_LED_OFF) | \
+ BIT(VSC8531_FORCE_LED_ON))
+
#define VSC85XX_SUPP_LED_MODES (BIT(VSC8531_LINK_ACTIVITY) | \
BIT(VSC8531_LINK_1000_ACTIVITY) | \
BIT(VSC8531_LINK_100_ACTIVITY) | \
@@ -137,6 +254,13 @@ enum rgmii_rx_clock_delay {
BIT(VSC8531_FORCE_LED_OFF) | \
BIT(VSC8531_FORCE_LED_ON))
+#define MSCC_VSC8584_REVB_INT8051_FW "mscc_vsc8584_revb_int8051_fb48.bin"
+#define MSCC_VSC8584_REVB_INT8051_FW_START_ADDR 0xe800
+#define MSCC_VSC8584_REVB_INT8051_FW_CRC 0xfb48
+
+#define VSC8584_REVB 0x0001
+#define MSCC_DEV_REV_MASK GENMASK(3, 0)
+
struct reg_val {
u16 reg;
u32 val;
@@ -178,6 +302,55 @@ static const struct vsc85xx_hw_stat vsc85xx_hw_stats[] = {
},
};
+static const struct vsc85xx_hw_stat vsc8584_hw_stats[] = {
+ {
+ .string = "phy_receive_errors",
+ .reg = MSCC_PHY_ERR_RX_CNT,
+ .page = MSCC_PHY_PAGE_STANDARD,
+ .mask = ERR_CNT_MASK,
+ }, {
+ .string = "phy_false_carrier",
+ .reg = MSCC_PHY_ERR_FALSE_CARRIER_CNT,
+ .page = MSCC_PHY_PAGE_STANDARD,
+ .mask = ERR_CNT_MASK,
+ }, {
+ .string = "phy_cu_media_link_disconnect",
+ .reg = MSCC_PHY_ERR_LINK_DISCONNECT_CNT,
+ .page = MSCC_PHY_PAGE_STANDARD,
+ .mask = ERR_CNT_MASK,
+ }, {
+ .string = "phy_cu_media_crc_good_count",
+ .reg = MSCC_PHY_CU_MEDIA_CRC_VALID_CNT,
+ .page = MSCC_PHY_PAGE_EXTENDED,
+ .mask = VALID_CRC_CNT_CRC_MASK,
+ }, {
+ .string = "phy_cu_media_crc_error_count",
+ .reg = MSCC_PHY_EXT_PHY_CNTL_4,
+ .page = MSCC_PHY_PAGE_EXTENDED,
+ .mask = ERR_CNT_MASK,
+ }, {
+ .string = "phy_serdes_tx_good_pkt_count",
+ .reg = MSCC_PHY_SERDES_TX_VALID_CNT,
+ .page = MSCC_PHY_PAGE_EXTENDED_3,
+ .mask = VALID_CRC_CNT_CRC_MASK,
+ }, {
+ .string = "phy_serdes_tx_bad_crc_count",
+ .reg = MSCC_PHY_SERDES_TX_CRC_ERR_CNT,
+ .page = MSCC_PHY_PAGE_EXTENDED_3,
+ .mask = ERR_CNT_MASK,
+ }, {
+ .string = "phy_serdes_rx_good_pkt_count",
+ .reg = MSCC_PHY_SERDES_RX_VALID_CNT,
+ .page = MSCC_PHY_PAGE_EXTENDED_3,
+ .mask = VALID_CRC_CNT_CRC_MASK,
+ }, {
+ .string = "phy_serdes_rx_bad_crc_count",
+ .reg = MSCC_PHY_SERDES_RX_CRC_ERR_CNT,
+ .page = MSCC_PHY_PAGE_EXTENDED_3,
+ .mask = ERR_CNT_MASK,
+ },
+};
+
struct vsc8531_private {
int rate_magic;
u16 supp_led_modes;
@@ -186,6 +359,11 @@ struct vsc8531_private {
const struct vsc85xx_hw_stat *hw_stats;
u64 *stats;
int nstats;
+ bool pkg_init;
+ /* For multiple port PHYs; the MDIO address of the base PHY in the
+ * package.
+ */
+ unsigned int base_addr;
};
#ifdef CONFIG_OF_MDIO
@@ -752,6 +930,509 @@ static int vsc85xx_eee_init_seq_set(struct phy_device *phydev)
return oldpage;
}
+/* phydev->bus->mdio_lock should be locked when using this function */
+static int phy_base_write(struct phy_device *phydev, u32 regnum, u16 val)
+{
+ struct vsc8531_private *priv = phydev->priv;
+
+ if (unlikely(!mutex_is_locked(&phydev->mdio.bus->mdio_lock))) {
+ dev_err(&phydev->mdio.dev, "MDIO bus lock not held!\n");
+ dump_stack();
+ }
+
+ return __mdiobus_write(phydev->mdio.bus, priv->base_addr, regnum, val);
+}
+
+/* phydev->bus->mdio_lock should be locked when using this function */
+static int phy_base_read(struct phy_device *phydev, u32 regnum)
+{
+ struct vsc8531_private *priv = phydev->priv;
+
+ if (unlikely(!mutex_is_locked(&phydev->mdio.bus->mdio_lock))) {
+ dev_err(&phydev->mdio.dev, "MDIO bus lock not held!\n");
+ dump_stack();
+ }
+
+ return __mdiobus_read(phydev->mdio.bus, priv->base_addr, regnum);
+}
+
+/* bus->mdio_lock should be locked when using this function */
+static void vsc8584_csr_write(struct phy_device *phydev, u16 addr, u32 val)
+{
+ phy_base_write(phydev, MSCC_PHY_TR_MSB, val >> 16);
+ phy_base_write(phydev, MSCC_PHY_TR_LSB, val & GENMASK(15, 0));
+ phy_base_write(phydev, MSCC_PHY_TR_CNTL, TR_WRITE | TR_ADDR(addr));
+}
+
+/* bus->mdio_lock should be locked when using this function */
+static int vsc8584_cmd(struct phy_device *phydev, u16 val)
+{
+ unsigned long deadline;
+ u16 reg_val;
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS,
+ MSCC_PHY_PAGE_EXTENDED_GPIO);
+
+ phy_base_write(phydev, MSCC_PHY_PROC_CMD, PROC_CMD_NCOMPLETED | val);
+
+ deadline = jiffies + msecs_to_jiffies(PROC_CMD_NCOMPLETED_TIMEOUT_MS);
+ do {
+ reg_val = phy_base_read(phydev, MSCC_PHY_PROC_CMD);
+ } while (time_before(jiffies, deadline) &&
+ (reg_val & PROC_CMD_NCOMPLETED) &&
+ !(reg_val & PROC_CMD_FAILED));
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
+
+ if (reg_val & PROC_CMD_FAILED)
+ return -EIO;
+
+ if (reg_val & PROC_CMD_NCOMPLETED)
+ return -ETIMEDOUT;
+
+ return 0;
+}
+
+/* bus->mdio_lock should be locked when using this function */
+static int vsc8584_micro_deassert_reset(struct phy_device *phydev,
+ bool patch_en)
+{
+ u32 enable, release;
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS,
+ MSCC_PHY_PAGE_EXTENDED_GPIO);
+
+ enable = RUN_FROM_INT_ROM | MICRO_CLK_EN | DW8051_CLK_EN;
+ release = MICRO_NSOFT_RESET | RUN_FROM_INT_ROM | DW8051_CLK_EN |
+ MICRO_CLK_EN;
+
+ if (patch_en) {
+ enable |= MICRO_PATCH_EN;
+ release |= MICRO_PATCH_EN;
+
+ /* Clear all patches */
+ phy_base_write(phydev, MSCC_INT_MEM_CNTL, READ_RAM);
+ }
+
+ /* Enable 8051 Micro clock; CLEAR/SET patch present; disable PRAM clock
+ * override and addr. auto-incr; operate at 125 MHz
+ */
+ phy_base_write(phydev, MSCC_DW8051_CNTL_STATUS, enable);
+ /* Release 8051 Micro SW reset */
+ phy_base_write(phydev, MSCC_DW8051_CNTL_STATUS, release);
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
+
+ return 0;
+}
+
+/* bus->mdio_lock should be locked when using this function */
+static int vsc8584_micro_assert_reset(struct phy_device *phydev)
+{
+ int ret;
+ u16 reg;
+
+ ret = vsc8584_cmd(phydev, PROC_CMD_NOP);
+ if (ret)
+ return ret;
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS,
+ MSCC_PHY_PAGE_EXTENDED_GPIO);
+
+ reg = phy_base_read(phydev, MSCC_INT_MEM_CNTL);
+ reg &= ~EN_PATCH_RAM_TRAP_ADDR(4);
+ phy_base_write(phydev, MSCC_INT_MEM_CNTL, reg);
+
+ phy_base_write(phydev, MSCC_TRAP_ROM_ADDR(4), 0x005b);
+ phy_base_write(phydev, MSCC_PATCH_RAM_ADDR(4), 0x005b);
+
+ reg = phy_base_read(phydev, MSCC_INT_MEM_CNTL);
+ reg |= EN_PATCH_RAM_TRAP_ADDR(4);
+ phy_base_write(phydev, MSCC_INT_MEM_CNTL, reg);
+
+ phy_base_write(phydev, MSCC_PHY_PROC_CMD, PROC_CMD_NOP);
+
+ reg = phy_base_read(phydev, MSCC_DW8051_CNTL_STATUS);
+ reg &= ~MICRO_NSOFT_RESET;
+ phy_base_write(phydev, MSCC_DW8051_CNTL_STATUS, reg);
+
+ phy_base_write(phydev, MSCC_PHY_PROC_CMD, PROC_CMD_MCB_ACCESS_MAC_CONF |
+ PROC_CMD_SGMII_PORT(0) | PROC_CMD_NO_MAC_CONF |
+ PROC_CMD_READ);
+
+ reg = phy_base_read(phydev, MSCC_INT_MEM_CNTL);
+ reg &= ~EN_PATCH_RAM_TRAP_ADDR(4);
+ phy_base_write(phydev, MSCC_INT_MEM_CNTL, reg);
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
+
+ return 0;
+}
+
+/* bus->mdio_lock should be locked when using this function */
+static int vsc8584_get_fw_crc(struct phy_device *phydev, u16 start, u16 size,
+ u16 *crc)
+{
+ int ret;
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_EXTENDED);
+
+ phy_base_write(phydev, MSCC_PHY_VERIPHY_CNTL_2, start);
+ phy_base_write(phydev, MSCC_PHY_VERIPHY_CNTL_3, size);
+
+ /* Start Micro command */
+ ret = vsc8584_cmd(phydev, PROC_CMD_CRC16);
+ if (ret)
+ goto out;
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_EXTENDED);
+
+ *crc = phy_base_read(phydev, MSCC_PHY_VERIPHY_CNTL_2);
+
+out:
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
+
+ return ret;
+}
+
+/* bus->mdio_lock should be locked when using this function */
+static int vsc8584_patch_fw(struct phy_device *phydev,
+ const struct firmware *fw)
+{
+ int i, ret;
+
+ ret = vsc8584_micro_assert_reset(phydev);
+ if (ret) {
+ dev_err(&phydev->mdio.dev,
+ "%s: failed to assert reset of micro\n", __func__);
+ return ret;
+ }
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS,
+ MSCC_PHY_PAGE_EXTENDED_GPIO);
+
+ /* Hold 8051 Micro in SW Reset, Enable auto incr address and patch clock
+ * Disable the 8051 Micro clock
+ */
+ phy_base_write(phydev, MSCC_DW8051_CNTL_STATUS, RUN_FROM_INT_ROM |
+ AUTOINC_ADDR | PATCH_RAM_CLK | MICRO_CLK_EN |
+ MICRO_CLK_DIVIDE(2));
+ phy_base_write(phydev, MSCC_INT_MEM_CNTL, READ_PRAM | INT_MEM_WRITE_EN |
+ INT_MEM_DATA(2));
+ phy_base_write(phydev, MSCC_INT_MEM_ADDR, 0x0000);
+
+ for (i = 0; i < fw->size; i++)
+ phy_base_write(phydev, MSCC_INT_MEM_CNTL, READ_PRAM |
+ INT_MEM_WRITE_EN | fw->data[i]);
+
+ /* Clear internal memory access */
+ phy_base_write(phydev, MSCC_INT_MEM_CNTL, READ_RAM);
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
+
+ return 0;
+}
+
+/* bus->mdio_lock should be locked when using this function */
+static int vsc8584_config_pre_init(struct phy_device *phydev)
+{
+ const struct reg_val pre_init1[] = {
+ {0x07fa, 0x0050100f},
+ {0x1688, 0x00049f81},
+ {0x0f90, 0x00688980},
+ {0x03a4, 0x0000d8f0},
+ {0x0fc0, 0x00000400},
+ {0x0f82, 0x0012b002},
+ {0x1686, 0x00000004},
+ {0x168c, 0x00d2c46f},
+ {0x17a2, 0x00000620},
+ {0x16a0, 0x00eeffdd},
+ {0x16a6, 0x00071448},
+ {0x16a4, 0x0013132f},
+ {0x16a8, 0x00000000},
+ {0x0ffc, 0x00c0a028},
+ {0x0fe8, 0x0091b06c},
+ {0x0fea, 0x00041600},
+ {0x0f80, 0x00fffaff},
+ {0x0fec, 0x00901809},
+ {0x0ffe, 0x00b01007},
+ {0x16b0, 0x00eeff00},
+ {0x16b2, 0x00007000},
+ {0x16b4, 0x00000814},
+ };
+ const struct reg_val pre_init2[] = {
+ {0x0486, 0x0008a518},
+ {0x0488, 0x006dc696},
+ {0x048a, 0x00000912},
+ };
+ const struct firmware *fw;
+ struct device *dev = &phydev->mdio.dev;
+ unsigned int i;
+ u16 crc, reg;
+ int ret;
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
+
+ /* all writes below are broadcasted to all PHYs in the same package */
+ reg = phy_base_read(phydev, MSCC_PHY_EXT_CNTL_STATUS);
+ reg |= SMI_BROADCAST_WR_EN;
+ phy_base_write(phydev, MSCC_PHY_EXT_CNTL_STATUS, reg);
+
+ phy_base_write(phydev, MII_VSC85XX_INT_MASK, 0);
+
+ reg = phy_base_read(phydev, MSCC_PHY_BYPASS_CONTROL);
+ reg |= PARALLEL_DET_IGNORE_ADVERTISED;
+ phy_base_write(phydev, MSCC_PHY_BYPASS_CONTROL, reg);
+
+ /* The below register writes are tweaking analog and electrical
+ * configuration that were determined through characterization by PHY
+ * engineers. These don't mean anything more than "these are the best
+ * values".
+ */
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_EXTENDED_3);
+
+ phy_base_write(phydev, MSCC_PHY_SERDES_TX_CRC_ERR_CNT, 0x2000);
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_TEST);
+
+ phy_base_write(phydev, MSCC_PHY_TEST_PAGE_5, 0x1f20);
+
+ reg = phy_base_read(phydev, MSCC_PHY_TEST_PAGE_8);
+ reg |= 0x8000;
+ phy_base_write(phydev, MSCC_PHY_TEST_PAGE_8, reg);
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_TR);
+
+ phy_base_write(phydev, MSCC_PHY_TR_CNTL, TR_WRITE | TR_ADDR(0x2fa4));
+
+ reg = phy_base_read(phydev, MSCC_PHY_TR_MSB);
+ reg &= ~0x007f;
+ reg |= 0x0019;
+ phy_base_write(phydev, MSCC_PHY_TR_MSB, reg);
+
+ phy_base_write(phydev, MSCC_PHY_TR_CNTL, TR_WRITE | TR_ADDR(0x0fa4));
+
+ for (i = 0; i < ARRAY_SIZE(pre_init1); i++)
+ vsc8584_csr_write(phydev, pre_init1[i].reg, pre_init1[i].val);
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_EXTENDED_2);
+
+ phy_base_write(phydev, MSCC_PHY_CU_PMD_TX_CNTL, 0x028e);
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_TR);
+
+ for (i = 0; i < ARRAY_SIZE(pre_init2); i++)
+ vsc8584_csr_write(phydev, pre_init2[i].reg, pre_init2[i].val);
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_TEST);
+
+ reg = phy_base_read(phydev, MSCC_PHY_TEST_PAGE_8);
+ reg &= ~0x8000;
+ phy_base_write(phydev, MSCC_PHY_TEST_PAGE_8, reg);
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
+
+ /* end of write broadcasting */
+ reg = phy_base_read(phydev, MSCC_PHY_EXT_CNTL_STATUS);
+ reg &= ~SMI_BROADCAST_WR_EN;
+ phy_base_write(phydev, MSCC_PHY_EXT_CNTL_STATUS, reg);
+
+ ret = request_firmware(&fw, MSCC_VSC8584_REVB_INT8051_FW, dev);
+ if (ret) {
+ dev_err(dev, "failed to load firmware %s, ret: %d\n",
+ MSCC_VSC8584_REVB_INT8051_FW, ret);
+ return ret;
+ }
+
+ /* Add one byte to size for the one added by the patch_fw function */
+ ret = vsc8584_get_fw_crc(phydev,
+ MSCC_VSC8584_REVB_INT8051_FW_START_ADDR,
+ fw->size + 1, &crc);
+ if (ret)
+ goto out;
+
+ if (crc != MSCC_VSC8584_REVB_INT8051_FW_CRC) {
+ dev_dbg(dev, "FW CRC is not the expected one, patching FW\n");
+ if (vsc8584_patch_fw(phydev, fw))
+ dev_warn(dev,
+ "failed to patch FW, expect non-optimal device\n");
+ }
+
+ vsc8584_micro_deassert_reset(phydev, false);
+
+ /* Add one byte to size for the one added by the patch_fw function */
+ ret = vsc8584_get_fw_crc(phydev,
+ MSCC_VSC8584_REVB_INT8051_FW_START_ADDR,
+ fw->size + 1, &crc);
+ if (ret)
+ goto out;
+
+ if (crc != MSCC_VSC8584_REVB_INT8051_FW_CRC)
+ dev_warn(dev,
+ "FW CRC after patching is not the expected one, expect non-optimal device\n");
+
+ ret = vsc8584_micro_assert_reset(phydev);
+ if (ret)
+ goto out;
+
+ vsc8584_micro_deassert_reset(phydev, true);
+
+out:
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
+
+ release_firmware(fw);
+
+ return ret;
+}
+
+/* Check if one PHY has already done the init of the parts common to all PHYs
+ * in the Quad PHY package.
+ */
+static bool vsc8584_is_pkg_init(struct phy_device *phydev, bool reversed)
+{
+ struct mdio_device **map = phydev->mdio.bus->mdio_map;
+ struct vsc8531_private *vsc8531;
+ struct phy_device *phy;
+ int i, addr;
+
+ /* VSC8584 is a Quad PHY */
+ for (i = 0; i < 4; i++) {
+ vsc8531 = phydev->priv;
+
+ if (reversed)
+ addr = vsc8531->base_addr - i;
+ else
+ addr = vsc8531->base_addr + i;
+
+ phy = container_of(map[addr], struct phy_device, mdio);
+
+ if ((phy->phy_id & phydev->drv->phy_id_mask) !=
+ (phydev->drv->phy_id & phydev->drv->phy_id_mask))
+ continue;
+
+ vsc8531 = phy->priv;
+
+ if (vsc8531 && vsc8531->pkg_init)
+ return true;
+ }
+
+ return false;
+}
+
+static int vsc8584_config_init(struct phy_device *phydev)
+{
+ struct vsc8531_private *vsc8531 = phydev->priv;
+ u16 addr, val;
+ int ret, i;
+
+ phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
+
+ mutex_lock(&phydev->mdio.bus->mdio_lock);
+
+ __mdiobus_write(phydev->mdio.bus, phydev->mdio.addr,
+ MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_EXTENDED);
+ addr = __mdiobus_read(phydev->mdio.bus, phydev->mdio.addr,
+ MSCC_PHY_EXT_PHY_CNTL_4);
+ addr >>= PHY_CNTL_4_ADDR_POS;
+
+ val = __mdiobus_read(phydev->mdio.bus, phydev->mdio.addr,
+ MSCC_PHY_ACTIPHY_CNTL);
+ if (val & PHY_ADDR_REVERSED)
+ vsc8531->base_addr = phydev->mdio.addr + addr;
+ else
+ vsc8531->base_addr = phydev->mdio.addr - addr;
+
+ /* Some parts of the init sequence are identical for every PHY in the
+ * package. Some parts are modifying the GPIO register bank which is a
+ * set of registers that are affecting all PHYs, a few resetting the
+ * microprocessor common to all PHYs. The CRC check responsible of the
+ * checking the firmware within the 8051 microprocessor can only be
+ * accessed via the PHY whose internal address in the package is 0.
+ * All PHYs' interrupts mask register has to be zeroed before enabling
+ * any PHY's interrupt in this register.
+ * For all these reasons, we need to do the init sequence once and only
+ * once whatever is the first PHY in the package that is initialized and
+ * do the correct init sequence for all PHYs that are package-critical
+ * in this pre-init function.
+ */
+ if (!vsc8584_is_pkg_init(phydev, val & PHY_ADDR_REVERSED ? 1 : 0)) {
+ ret = vsc8584_config_pre_init(phydev);
+ if (ret)
+ goto err;
+ }
+
+ vsc8531->pkg_init = true;
+
+ phy_base_write(phydev, MSCC_EXT_PAGE_ACCESS,
+ MSCC_PHY_PAGE_EXTENDED_GPIO);
+
+ val = phy_base_read(phydev, MSCC_PHY_MAC_CFG_FASTLINK);
+ val &= ~MAC_CFG_MASK;
+ if (phydev->interface == PHY_INTERFACE_MODE_QSGMII)
+ val |= MAC_CFG_QSGMII;
+ else
+ val |= MAC_CFG_SGMII;
+
+ ret = phy_base_write(phydev, MSCC_PHY_MAC_CFG_FASTLINK, val);
+ if (ret)
+ goto err;
+
+ val = PROC_CMD_MCB_ACCESS_MAC_CONF | PROC_CMD_RST_CONF_PORT |
+ PROC_CMD_READ_MOD_WRITE_PORT;
+ if (phydev->interface == PHY_INTERFACE_MODE_QSGMII)
+ val |= PROC_CMD_QSGMII_MAC;
+ else
+ val |= PROC_CMD_SGMII_MAC;
+
+ ret = vsc8584_cmd(phydev, val);
+ if (ret)
+ goto err;
+
+ usleep_range(10000, 20000);
+
+ /* Disable SerDes for 100Base-FX */
+ ret = vsc8584_cmd(phydev, PROC_CMD_FIBER_MEDIA_CONF |
+ PROC_CMD_FIBER_PORT(addr) | PROC_CMD_FIBER_DISABLE |
+ PROC_CMD_READ_MOD_WRITE_PORT |
+ PROC_CMD_RST_CONF_PORT | PROC_CMD_FIBER_100BASE_FX);
+ if (ret)
+ goto err;
+
+ /* Disable SerDes for 1000Base-X */
+ ret = vsc8584_cmd(phydev, PROC_CMD_FIBER_MEDIA_CONF |
+ PROC_CMD_FIBER_PORT(addr) | PROC_CMD_FIBER_DISABLE |
+ PROC_CMD_READ_MOD_WRITE_PORT |
+ PROC_CMD_RST_CONF_PORT | PROC_CMD_FIBER_1000BASE_X);
+ if (ret)
+ goto err;
+
+ mutex_unlock(&phydev->mdio.bus->mdio_lock);
+
+ phy_write(phydev, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_STANDARD);
+
+ val = phy_read(phydev, MSCC_PHY_EXT_PHY_CNTL_1);
+ val &= ~(MEDIA_OP_MODE_MASK | VSC8584_MAC_IF_SELECTION_MASK);
+ val |= MEDIA_OP_MODE_COPPER | (VSC8584_MAC_IF_SELECTION_SGMII <<
+ VSC8584_MAC_IF_SELECTION_POS);
+ ret = phy_write(phydev, MSCC_PHY_EXT_PHY_CNTL_1, val);
+
+ ret = genphy_soft_reset(phydev);
+ if (ret)
+ return ret;
+
+ for (i = 0; i < vsc8531->nleds; i++) {
+ ret = vsc85xx_led_cntl_set(phydev, i, vsc8531->leds_mode[i]);
+ if (ret)
+ return ret;
+ }
+
+ return genphy_config_init(phydev);
+
+err:
+ mutex_unlock(&phydev->mdio.bus->mdio_lock);
+ return ret;
+}
+
static int vsc85xx_config_init(struct phy_device *phydev)
{
int rc, i;
@@ -782,6 +1463,16 @@ static int vsc85xx_config_init(struct phy_device *phydev)
return genphy_config_init(phydev);
}
+static int vsc8584_did_interrupt(struct phy_device *phydev)
+{
+ int rc = 0;
+
+ if (phydev->interrupts == PHY_INTERRUPT_ENABLED)
+ rc = phy_read(phydev, MII_VSC85XX_INT_STATUS);
+
+ return (rc < 0) ? 0 : rc & MII_VSC85XX_INT_MASK_MASK;
+}
+
static int vsc85xx_ack_interrupt(struct phy_device *phydev)
{
int rc = 0;
@@ -831,6 +1522,36 @@ static int vsc85xx_read_status(struct phy_device *phydev)
return genphy_read_status(phydev);
}
+static int vsc8584_probe(struct phy_device *phydev)
+{
+ struct vsc8531_private *vsc8531;
+ u32 default_mode[4] = {VSC8531_LINK_1000_ACTIVITY,
+ VSC8531_LINK_100_ACTIVITY, VSC8531_LINK_ACTIVITY,
+ VSC8531_DUPLEX_COLLISION};
+
+ if ((phydev->phy_id & MSCC_DEV_REV_MASK) != VSC8584_REVB) {
+ dev_err(&phydev->mdio.dev, "Only VSC8584 revB is supported.\n");
+ return -ENOTSUPP;
+ }
+
+ vsc8531 = devm_kzalloc(&phydev->mdio.dev, sizeof(*vsc8531), GFP_KERNEL);
+ if (!vsc8531)
+ return -ENOMEM;
+
+ phydev->priv = vsc8531;
+
+ vsc8531->nleds = 4;
+ vsc8531->supp_led_modes = VSC8584_SUPP_LED_MODES;
+ vsc8531->hw_stats = vsc8584_hw_stats;
+ vsc8531->nstats = ARRAY_SIZE(vsc8584_hw_stats);
+ vsc8531->stats = devm_kmalloc_array(&phydev->mdio.dev, vsc8531->nstats,
+ sizeof(u64), GFP_KERNEL);
+ if (!vsc8531->stats)
+ return -ENOMEM;
+
+ return vsc85xx_dt_led_modes_get(phydev, default_mode);
+}
+
static int vsc85xx_probe(struct phy_device *phydev)
{
struct vsc8531_private *vsc8531;
@@ -966,6 +1687,31 @@ static struct phy_driver vsc85xx_driver[] = {
.get_sset_count = &vsc85xx_get_sset_count,
.get_strings = &vsc85xx_get_strings,
.get_stats = &vsc85xx_get_stats,
+},
+{
+ .phy_id = PHY_ID_VSC8584,
+ .name = "Microsemi GE VSC8584 SyncE",
+ .phy_id_mask = 0xfffffff0,
+ .features = PHY_GBIT_FEATURES,
+ .flags = PHY_HAS_INTERRUPT,
+ .soft_reset = &genphy_soft_reset,
+ .config_init = &vsc8584_config_init,
+ .config_aneg = &vsc85xx_config_aneg,
+ .aneg_done = &genphy_aneg_done,
+ .read_status = &vsc85xx_read_status,
+ .ack_interrupt = &vsc85xx_ack_interrupt,
+ .config_intr = &vsc85xx_config_intr,
+ .did_interrupt = &vsc8584_did_interrupt,
+ .suspend = &genphy_suspend,
+ .resume = &genphy_resume,
+ .probe = &vsc8584_probe,
+ .get_tunable = &vsc85xx_get_tunable,
+ .set_tunable = &vsc85xx_set_tunable,
+ .read_page = &vsc85xx_phy_read_page,
+ .write_page = &vsc85xx_phy_write_page,
+ .get_sset_count = &vsc85xx_get_sset_count,
+ .get_strings = &vsc85xx_get_strings,
+ .get_stats = &vsc85xx_get_stats,
}
};
@@ -977,6 +1723,7 @@ static struct mdio_device_id __maybe_unused vsc85xx_tbl[] = {
{ PHY_ID_VSC8531, 0xfffffff0, },
{ PHY_ID_VSC8540, 0xfffffff0, },
{ PHY_ID_VSC8541, 0xfffffff0, },
+ { PHY_ID_VSC8584, 0xfffffff0, },
{ }
};
--
2.17.1
The VSC8584 (and most likely other PHYs in the same generation) has two
additional LED modes that can be picked, so let's add them.
Reviewed-by: Rob Herring <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
---
include/dt-bindings/net/mscc-phy-vsc8531.h | 2 ++
1 file changed, 2 insertions(+)
diff --git a/include/dt-bindings/net/mscc-phy-vsc8531.h b/include/dt-bindings/net/mscc-phy-vsc8531.h
index 697161f80eb5..9eb2ec2b2ea9 100644
--- a/include/dt-bindings/net/mscc-phy-vsc8531.h
+++ b/include/dt-bindings/net/mscc-phy-vsc8531.h
@@ -18,9 +18,11 @@
#define VSC8531_LINK_100_1000_ACTIVITY 4
#define VSC8531_LINK_10_1000_ACTIVITY 5
#define VSC8531_LINK_10_100_ACTIVITY 6
+#define VSC8584_LINK_100FX_1000X_ACTIVITY 7
#define VSC8531_DUPLEX_COLLISION 8
#define VSC8531_COLLISION 9
#define VSC8531_ACTIVITY 10
+#define VSC8584_100FX_1000X_ACTIVITY 11
#define VSC8531_AUTONEG_FAULT 12
#define VSC8531_SERIAL_MODE 13
#define VSC8531_FORCE_LED_OFF 14
--
2.17.1
From: Quentin Schulz <[email protected]>
Date: Thu, 4 Oct 2018 15:17:05 +0200
> I suggest patches 1 to 3 go through net tree and patches 4 and 5 go
> through MIPS tree. Patches going through net tree and those going through
> MIPS tree do not depend on one another.
Sounds like a good plan but patches 1-3 do not apply to net-next, please
respin.
Thank you.
Hi David,
On Fri, Oct 05, 2018 at 02:42:43PM -0700, David Miller wrote:
> From: Quentin Schulz <[email protected]>
> Date: Thu, 4 Oct 2018 15:17:05 +0200
>
> > I suggest patches 1 to 3 go through net tree and patches 4 and 5 go
> > through MIPS tree. Patches going through net tree and those going through
> > MIPS tree do not depend on one another.
>
> Sounds like a good plan but patches 1-3 do not apply to net-next, please
> respin.
>
Could it be because we're missing the patch series dependency? This
series depends on
https://lore.kernel.org/lkml/[email protected]/
which isn't merged yet.
I'll address the comment in the aforementioned patch series ASAP, send a
new version and respin this patch series at the same time.
Thanks,
Quentin