PAGE_READ is used by RISC-V arch code included through mm headers,
and it makes sense to bring in a prefix on these in the driver.
drivers/mtd/nand/raw/qcom_nandc.c:153: warning: "PAGE_READ" redefined
#define PAGE_READ 0x2
In file included from include/linux/memremap.h:7,
from include/linux/mm.h:27,
from include/linux/scatterlist.h:8,
from include/linux/dma-mapping.h:11,
from drivers/mtd/nand/raw/qcom_nandc.c:17:
arch/riscv/include/asm/pgtable.h:48: note: this is the location of the previous definition
Caught by riscv allmodconfig.
Signed-off-by: Olof Johansson <[email protected]>
---
drivers/mtd/nand/raw/qcom_nandc.c | 32 ++++++++++++++++----------------
1 file changed, 16 insertions(+), 16 deletions(-)
diff --git a/drivers/mtd/nand/raw/qcom_nandc.c b/drivers/mtd/nand/raw/qcom_nandc.c
index ef75dfa62a4f8..699d3cf49c6da 100644
--- a/drivers/mtd/nand/raw/qcom_nandc.c
+++ b/drivers/mtd/nand/raw/qcom_nandc.c
@@ -150,15 +150,15 @@
#define NAND_VERSION_MINOR_SHIFT 16
/* NAND OP_CMDs */
-#define PAGE_READ 0x2
-#define PAGE_READ_WITH_ECC 0x3
-#define PAGE_READ_WITH_ECC_SPARE 0x4
-#define PROGRAM_PAGE 0x6
-#define PAGE_PROGRAM_WITH_ECC 0x7
-#define PROGRAM_PAGE_SPARE 0x9
-#define BLOCK_ERASE 0xa
-#define FETCH_ID 0xb
-#define RESET_DEVICE 0xd
+#define OP_PAGE_READ 0x2
+#define OP_PAGE_READ_WITH_ECC 0x3
+#define OP_PAGE_READ_WITH_ECC_SPARE 0x4
+#define OP_PROGRAM_PAGE 0x6
+#define OP_PAGE_PROGRAM_WITH_ECC 0x7
+#define OP_PROGRAM_PAGE_SPARE 0x9
+#define OP_BLOCK_ERASE 0xa
+#define OP_FETCH_ID 0xb
+#define OP_RESET_DEVICE 0xd
/* Default Value for NAND_DEV_CMD_VLD */
#define NAND_DEV_CMD_VLD_VAL (READ_START_VLD | WRITE_START_VLD | \
@@ -692,11 +692,11 @@ static void update_rw_regs(struct qcom_nand_host *host, int num_cw, bool read)
if (read) {
if (host->use_ecc)
- cmd = PAGE_READ_WITH_ECC | PAGE_ACC | LAST_PAGE;
+ cmd = OP_PAGE_READ_WITH_ECC | PAGE_ACC | LAST_PAGE;
else
- cmd = PAGE_READ | PAGE_ACC | LAST_PAGE;
+ cmd = OP_PAGE_READ | PAGE_ACC | LAST_PAGE;
} else {
- cmd = PROGRAM_PAGE | PAGE_ACC | LAST_PAGE;
+ cmd = OP_PROGRAM_PAGE | PAGE_ACC | LAST_PAGE;
}
if (host->use_ecc) {
@@ -1170,7 +1170,7 @@ static int nandc_param(struct qcom_nand_host *host)
* in use. we configure the controller to perform a raw read of 512
* bytes to read onfi params
*/
- nandc_set_reg(nandc, NAND_FLASH_CMD, PAGE_READ | PAGE_ACC | LAST_PAGE);
+ nandc_set_reg(nandc, NAND_FLASH_CMD, OP_PAGE_READ | PAGE_ACC | LAST_PAGE);
nandc_set_reg(nandc, NAND_ADDR0, 0);
nandc_set_reg(nandc, NAND_ADDR1, 0);
nandc_set_reg(nandc, NAND_DEV0_CFG0, 0 << CW_PER_PAGE
@@ -1224,7 +1224,7 @@ static int erase_block(struct qcom_nand_host *host, int page_addr)
struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip);
nandc_set_reg(nandc, NAND_FLASH_CMD,
- BLOCK_ERASE | PAGE_ACC | LAST_PAGE);
+ OP_BLOCK_ERASE | PAGE_ACC | LAST_PAGE);
nandc_set_reg(nandc, NAND_ADDR0, page_addr);
nandc_set_reg(nandc, NAND_ADDR1, 0);
nandc_set_reg(nandc, NAND_DEV0_CFG0,
@@ -1255,7 +1255,7 @@ static int read_id(struct qcom_nand_host *host, int column)
if (column == -1)
return 0;
- nandc_set_reg(nandc, NAND_FLASH_CMD, FETCH_ID);
+ nandc_set_reg(nandc, NAND_FLASH_CMD, OP_FETCH_ID);
nandc_set_reg(nandc, NAND_ADDR0, column);
nandc_set_reg(nandc, NAND_ADDR1, 0);
nandc_set_reg(nandc, NAND_FLASH_CHIP_SELECT,
@@ -1276,7 +1276,7 @@ static int reset(struct qcom_nand_host *host)
struct nand_chip *chip = &host->chip;
struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip);
- nandc_set_reg(nandc, NAND_FLASH_CMD, RESET_DEVICE);
+ nandc_set_reg(nandc, NAND_FLASH_CMD, OP_RESET_DEVICE);
nandc_set_reg(nandc, NAND_EXEC_CMD, 1);
write_reg_dma(nandc, NAND_FLASH_CMD, 1, NAND_BAM_NEXT_SGL);
--
2.11.0
Hi Olof,
Olof Johansson <[email protected]> wrote on Fri, 16 Nov 2018 19:43:27
-0800:
> PAGE_READ is used by RISC-V arch code included through mm headers,
> and it makes sense to bring in a prefix on these in the driver.
>
> drivers/mtd/nand/raw/qcom_nandc.c:153: warning: "PAGE_READ" redefined
> #define PAGE_READ 0x2
> In file included from include/linux/memremap.h:7,
> from include/linux/mm.h:27,
> from include/linux/scatterlist.h:8,
> from include/linux/dma-mapping.h:11,
> from drivers/mtd/nand/raw/qcom_nandc.c:17:
> arch/riscv/include/asm/pgtable.h:48: note: this is the location of the previous definition
>
> Caught by riscv allmodconfig.
>
> Signed-off-by: Olof Johansson <[email protected]>
> ---
Reviewed-by: Miquel Raynal <[email protected]>
Boris, do you want to queue this as a fix?
Thanks,
Miquèl
On Sat, 2018-11-17 at 03:43:27 UTC, Olof Johansson wrote:
> PAGE_READ is used by RISC-V arch code included through mm headers,
> and it makes sense to bring in a prefix on these in the driver.
>
> drivers/mtd/nand/raw/qcom_nandc.c:153: warning: "PAGE_READ" redefined
> #define PAGE_READ 0x2
> In file included from include/linux/memremap.h:7,
> from include/linux/mm.h:27,
> from include/linux/scatterlist.h:8,
> from include/linux/dma-mapping.h:11,
> from drivers/mtd/nand/raw/qcom_nandc.c:17:
> arch/riscv/include/asm/pgtable.h:48: note: this is the location of the previous definition
>
> Caught by riscv allmodconfig.
>
> Signed-off-by: Olof Johansson <[email protected]>
> Reviewed-by: Miquel Raynal <[email protected]>
Applied to http://git.infradead.org/linux-mtd.git master, thanks.
Boris