Since v2.6.22 or so there has been reports [1] about OMAP MMC being
broken on OMAP15XX based hardware (OMAP5912 and OMAP310). The breakage
seems to have been caused by commit 46a6730e3ff9 ("mmc-omap: Fix
omap to use MMC_POWER_ON") that changed clock enabling to be done
on MMC_POWER_ON. This can happen multiple times in a row, and on 15XX
the hardware doesn't seem to like it and the MMC just stops responding.
Fix by memorizing the power mode and do the init only when necessary.
Before the patch (on Palm TE):
mmc0: new SD card at address b368
mmcblk0: mmc0:b368 SDC 977 MiB
mmci-omap mmci-omap.0: command timeout (CMD18)
mmci-omap mmci-omap.0: command timeout (CMD13)
mmci-omap mmci-omap.0: command timeout (CMD13)
mmci-omap mmci-omap.0: command timeout (CMD12) [x 6]
mmci-omap mmci-omap.0: command timeout (CMD13) [x 6]
mmcblk0: error -110 requesting status
mmci-omap mmci-omap.0: command timeout (CMD8)
mmci-omap mmci-omap.0: command timeout (CMD18)
mmci-omap mmci-omap.0: command timeout (CMD13)
mmci-omap mmci-omap.0: command timeout (CMD13)
mmci-omap mmci-omap.0: command timeout (CMD12) [x 6]
mmci-omap mmci-omap.0: command timeout (CMD13) [x 6]
mmcblk0: error -110 requesting status
mmcblk0: recovery failed!
print_req_error: I/O error, dev mmcblk0, sector 0
Buffer I/O error on dev mmcblk0, logical block 0, async page read
mmcblk0: unable to read partition table
After the patch:
mmc0: new SD card at address b368
mmcblk0: mmc0:b368 SDC 977 MiB
mmcblk0: p1
The patch is based on a fix and analysis done by Ladislav Michl.
Tested on OMAP15XX/OMAP310 (Palm TE), OMAP1710 (Nokia 770)
and OMAP2420 (Nokia N810).
[1] https://marc.info/?t=123175197000003&r=1&w=2
Fixes: 46a6730e3ff9 ("mmc-omap: Fix omap to use MMC_POWER_ON")
Reported-by: Ladislav Michl <[email protected]>
Reported-by: Andrzej Zaborowski <[email protected]>
Signed-off-by: Aaro Koskinen <[email protected]>
---
drivers/mmc/host/omap.c | 11 +++++++++--
1 file changed, 9 insertions(+), 2 deletions(-)
diff --git a/drivers/mmc/host/omap.c b/drivers/mmc/host/omap.c
index adf32682f27a..c60a7625b1fa 100644
--- a/drivers/mmc/host/omap.c
+++ b/drivers/mmc/host/omap.c
@@ -104,6 +104,7 @@ struct mmc_omap_slot {
unsigned int vdd;
u16 saved_con;
u16 bus_mode;
+ u16 power_mode;
unsigned int fclk_freq;
struct tasklet_struct cover_tasklet;
@@ -1157,7 +1158,7 @@ static void mmc_omap_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
struct mmc_omap_slot *slot = mmc_priv(mmc);
struct mmc_omap_host *host = slot->host;
int i, dsor;
- int clk_enabled;
+ int clk_enabled, init_stream;
mmc_omap_select_slot(slot, 0);
@@ -1167,6 +1168,7 @@ static void mmc_omap_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
slot->vdd = ios->vdd;
clk_enabled = 0;
+ init_stream = 0;
switch (ios->power_mode) {
case MMC_POWER_OFF:
mmc_omap_set_power(slot, 0, ios->vdd);
@@ -1174,13 +1176,17 @@ static void mmc_omap_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
case MMC_POWER_UP:
/* Cannot touch dsor yet, just power up MMC */
mmc_omap_set_power(slot, 1, ios->vdd);
+ slot->power_mode = ios->power_mode;
goto exit;
case MMC_POWER_ON:
mmc_omap_fclk_enable(host, 1);
clk_enabled = 1;
dsor |= 1 << 11;
+ if (slot->power_mode != MMC_POWER_ON)
+ init_stream = 1;
break;
}
+ slot->power_mode = ios->power_mode;
if (slot->bus_mode != ios->bus_mode) {
if (slot->pdata->set_bus_mode != NULL)
@@ -1196,7 +1202,7 @@ static void mmc_omap_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
for (i = 0; i < 2; i++)
OMAP_MMC_WRITE(host, CON, dsor);
slot->saved_con = dsor;
- if (ios->power_mode == MMC_POWER_ON) {
+ if (init_stream) {
/* worst case at 400kHz, 80 cycles makes 200 microsecs */
int usecs = 250;
@@ -1234,6 +1240,7 @@ static int mmc_omap_new_slot(struct mmc_omap_host *host, int id)
slot->host = host;
slot->mmc = mmc;
slot->id = id;
+ slot->power_mode = MMC_POWER_UNDEFINED;
slot->pdata = &host->pdata->slots[id];
host->slots[id] = slot;
--
2.17.0
Aaro,
On Sun, Nov 18, 2018 at 10:19:19PM +0200, Aaro Koskinen wrote:
> Since v2.6.22 or so there has been reports [1] about OMAP MMC being
> broken on OMAP15XX based hardware (OMAP5912 and OMAP310). The breakage
> seems to have been caused by commit 46a6730e3ff9 ("mmc-omap: Fix
> omap to use MMC_POWER_ON") that changed clock enabling to be done
> on MMC_POWER_ON. This can happen multiple times in a row, and on 15XX
> the hardware doesn't seem to like it and the MMC just stops responding.
> Fix by memorizing the power mode and do the init only when necessary.
I'm going to use this patch as an argument against anybody complaining
kernel bugs do not get fixed. People just need to teach themselves to
be patient.
Tested-by: Ladislav Michl <[email protected]>
> Before the patch (on Palm TE):
>
> mmc0: new SD card at address b368
> mmcblk0: mmc0:b368 SDC 977 MiB
> mmci-omap mmci-omap.0: command timeout (CMD18)
> mmci-omap mmci-omap.0: command timeout (CMD13)
> mmci-omap mmci-omap.0: command timeout (CMD13)
> mmci-omap mmci-omap.0: command timeout (CMD12) [x 6]
> mmci-omap mmci-omap.0: command timeout (CMD13) [x 6]
> mmcblk0: error -110 requesting status
> mmci-omap mmci-omap.0: command timeout (CMD8)
> mmci-omap mmci-omap.0: command timeout (CMD18)
> mmci-omap mmci-omap.0: command timeout (CMD13)
> mmci-omap mmci-omap.0: command timeout (CMD13)
> mmci-omap mmci-omap.0: command timeout (CMD12) [x 6]
> mmci-omap mmci-omap.0: command timeout (CMD13) [x 6]
> mmcblk0: error -110 requesting status
> mmcblk0: recovery failed!
> print_req_error: I/O error, dev mmcblk0, sector 0
> Buffer I/O error on dev mmcblk0, logical block 0, async page read
> mmcblk0: unable to read partition table
>
> After the patch:
>
> mmc0: new SD card at address b368
> mmcblk0: mmc0:b368 SDC 977 MiB
> mmcblk0: p1
>
> The patch is based on a fix and analysis done by Ladislav Michl.
>
> Tested on OMAP15XX/OMAP310 (Palm TE), OMAP1710 (Nokia 770)
> and OMAP2420 (Nokia N810).
>
> [1] https://marc.info/?t=123175197000003&r=1&w=2
>
> Fixes: 46a6730e3ff9 ("mmc-omap: Fix omap to use MMC_POWER_ON")
> Reported-by: Ladislav Michl <[email protected]>
> Reported-by: Andrzej Zaborowski <[email protected]>
> Signed-off-by: Aaro Koskinen <[email protected]>
> ---
> drivers/mmc/host/omap.c | 11 +++++++++--
> 1 file changed, 9 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/mmc/host/omap.c b/drivers/mmc/host/omap.c
> index adf32682f27a..c60a7625b1fa 100644
> --- a/drivers/mmc/host/omap.c
> +++ b/drivers/mmc/host/omap.c
> @@ -104,6 +104,7 @@ struct mmc_omap_slot {
> unsigned int vdd;
> u16 saved_con;
> u16 bus_mode;
> + u16 power_mode;
> unsigned int fclk_freq;
>
> struct tasklet_struct cover_tasklet;
> @@ -1157,7 +1158,7 @@ static void mmc_omap_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
> struct mmc_omap_slot *slot = mmc_priv(mmc);
> struct mmc_omap_host *host = slot->host;
> int i, dsor;
> - int clk_enabled;
> + int clk_enabled, init_stream;
>
> mmc_omap_select_slot(slot, 0);
>
> @@ -1167,6 +1168,7 @@ static void mmc_omap_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
> slot->vdd = ios->vdd;
>
> clk_enabled = 0;
> + init_stream = 0;
> switch (ios->power_mode) {
> case MMC_POWER_OFF:
> mmc_omap_set_power(slot, 0, ios->vdd);
> @@ -1174,13 +1176,17 @@ static void mmc_omap_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
> case MMC_POWER_UP:
> /* Cannot touch dsor yet, just power up MMC */
> mmc_omap_set_power(slot, 1, ios->vdd);
> + slot->power_mode = ios->power_mode;
> goto exit;
> case MMC_POWER_ON:
> mmc_omap_fclk_enable(host, 1);
> clk_enabled = 1;
> dsor |= 1 << 11;
> + if (slot->power_mode != MMC_POWER_ON)
> + init_stream = 1;
> break;
> }
> + slot->power_mode = ios->power_mode;
>
> if (slot->bus_mode != ios->bus_mode) {
> if (slot->pdata->set_bus_mode != NULL)
> @@ -1196,7 +1202,7 @@ static void mmc_omap_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
> for (i = 0; i < 2; i++)
> OMAP_MMC_WRITE(host, CON, dsor);
> slot->saved_con = dsor;
> - if (ios->power_mode == MMC_POWER_ON) {
> + if (init_stream) {
> /* worst case at 400kHz, 80 cycles makes 200 microsecs */
> int usecs = 250;
>
> @@ -1234,6 +1240,7 @@ static int mmc_omap_new_slot(struct mmc_omap_host *host, int id)
> slot->host = host;
> slot->mmc = mmc;
> slot->id = id;
> + slot->power_mode = MMC_POWER_UNDEFINED;
> slot->pdata = &host->pdata->slots[id];
>
> host->slots[id] = slot;
> --
> 2.17.0
* Ladislav Michl <[email protected]> [181118 22:22]:
> Aaro,
>
> On Sun, Nov 18, 2018 at 10:19:19PM +0200, Aaro Koskinen wrote:
> > Since v2.6.22 or so there has been reports [1] about OMAP MMC being
> > broken on OMAP15XX based hardware (OMAP5912 and OMAP310). The breakage
> > seems to have been caused by commit 46a6730e3ff9 ("mmc-omap: Fix
> > omap to use MMC_POWER_ON") that changed clock enabling to be done
> > on MMC_POWER_ON. This can happen multiple times in a row, and on 15XX
> > the hardware doesn't seem to like it and the MMC just stops responding.
> > Fix by memorizing the power mode and do the init only when necessary.
>
> I'm going to use this patch as an argument against anybody complaining
> kernel bugs do not get fixed. People just need to teach themselves to
> be patient.
Yup, good to have more usable devices :) And thanks for fixing it:
Acked-by: Tony Lindgren <[email protected]>
Aaro,
On 2018-11-18 22:19, Aaro Koskinen wrote:
> Since v2.6.22 or so there has been reports [1] about OMAP MMC being
> broken on OMAP15XX based hardware (OMAP5912 and OMAP310). The breakage
> seems to have been caused by commit 46a6730e3ff9 ("mmc-omap: Fix
> omap to use MMC_POWER_ON") that changed clock enabling to be done
> on MMC_POWER_ON. This can happen multiple times in a row, and on 15XX
> the hardware doesn't seem to like it and the MMC just stops responding.
> Fix by memorizing the power mode and do the init only when necessary.
>
> Before the patch (on Palm TE):
>
> mmc0: new SD card at address b368
> mmcblk0: mmc0:b368 SDC 977 MiB
> mmci-omap mmci-omap.0: command timeout (CMD18)
> mmci-omap mmci-omap.0: command timeout (CMD13)
> mmci-omap mmci-omap.0: command timeout (CMD13)
> mmci-omap mmci-omap.0: command timeout (CMD12) [x 6]
> mmci-omap mmci-omap.0: command timeout (CMD13) [x 6]
> mmcblk0: error -110 requesting status
> mmci-omap mmci-omap.0: command timeout (CMD8)
> mmci-omap mmci-omap.0: command timeout (CMD18)
> mmci-omap mmci-omap.0: command timeout (CMD13)
> mmci-omap mmci-omap.0: command timeout (CMD13)
> mmci-omap mmci-omap.0: command timeout (CMD12) [x 6]
> mmci-omap mmci-omap.0: command timeout (CMD13) [x 6]
> mmcblk0: error -110 requesting status
> mmcblk0: recovery failed!
> print_req_error: I/O error, dev mmcblk0, sector 0
> Buffer I/O error on dev mmcblk0, logical block 0, async page read
> mmcblk0: unable to read partition table
>
> After the patch:
>
> mmc0: new SD card at address b368
> mmcblk0: mmc0:b368 SDC 977 MiB
> mmcblk0: p1
>
> The patch is based on a fix and analysis done by Ladislav Michl.
>
> Tested on OMAP15XX/OMAP310 (Palm TE), OMAP1710 (Nokia 770)
> and OMAP2420 (Nokia N810).
Do you know if the DMA is enabled for the MMC? It might not work via
DMAengine.
> [1] https://marc.info/?t=123175197000003&r=1&w=2
>
> Fixes: 46a6730e3ff9 ("mmc-omap: Fix omap to use MMC_POWER_ON")
> Reported-by: Ladislav Michl <[email protected]>
> Reported-by: Andrzej Zaborowski <[email protected]>
> Signed-off-by: Aaro Koskinen <[email protected]>
> ---
> drivers/mmc/host/omap.c | 11 +++++++++--
> 1 file changed, 9 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/mmc/host/omap.c b/drivers/mmc/host/omap.c
> index adf32682f27a..c60a7625b1fa 100644
> --- a/drivers/mmc/host/omap.c
> +++ b/drivers/mmc/host/omap.c
> @@ -104,6 +104,7 @@ struct mmc_omap_slot {
> unsigned int vdd;
> u16 saved_con;
> u16 bus_mode;
> + u16 power_mode;
> unsigned int fclk_freq;
>
> struct tasklet_struct cover_tasklet;
> @@ -1157,7 +1158,7 @@ static void mmc_omap_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
> struct mmc_omap_slot *slot = mmc_priv(mmc);
> struct mmc_omap_host *host = slot->host;
> int i, dsor;
> - int clk_enabled;
> + int clk_enabled, init_stream;
>
> mmc_omap_select_slot(slot, 0);
>
> @@ -1167,6 +1168,7 @@ static void mmc_omap_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
> slot->vdd = ios->vdd;
>
> clk_enabled = 0;
> + init_stream = 0;
> switch (ios->power_mode) {
> case MMC_POWER_OFF:
> mmc_omap_set_power(slot, 0, ios->vdd);
> @@ -1174,13 +1176,17 @@ static void mmc_omap_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
> case MMC_POWER_UP:
> /* Cannot touch dsor yet, just power up MMC */
> mmc_omap_set_power(slot, 1, ios->vdd);
> + slot->power_mode = ios->power_mode;
> goto exit;
> case MMC_POWER_ON:
> mmc_omap_fclk_enable(host, 1);
> clk_enabled = 1;
> dsor |= 1 << 11;
> + if (slot->power_mode != MMC_POWER_ON)
> + init_stream = 1;
> break;
> }
> + slot->power_mode = ios->power_mode;
>
> if (slot->bus_mode != ios->bus_mode) {
> if (slot->pdata->set_bus_mode != NULL)
> @@ -1196,7 +1202,7 @@ static void mmc_omap_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
> for (i = 0; i < 2; i++)
> OMAP_MMC_WRITE(host, CON, dsor);
> slot->saved_con = dsor;
> - if (ios->power_mode == MMC_POWER_ON) {
> + if (init_stream) {
> /* worst case at 400kHz, 80 cycles makes 200 microsecs */
> int usecs = 250;
>
> @@ -1234,6 +1240,7 @@ static int mmc_omap_new_slot(struct mmc_omap_host *host, int id)
> slot->host = host;
> slot->mmc = mmc;
> slot->id = id;
> + slot->power_mode = MMC_POWER_UNDEFINED;
> slot->pdata = &host->pdata->slots[id];
>
> host->slots[id] = slot;
>
- Péter
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
Hi,
On Mon, Nov 19, 2018 at 11:58:32AM +0200, Peter Ujfalusi wrote:
> On 2018-11-18 22:19, Aaro Koskinen wrote:
> > Tested on OMAP15XX/OMAP310 (Palm TE), OMAP1710 (Nokia 770)
> > and OMAP2420 (Nokia N810).
>
> Do you know if the DMA is enabled for the MMC? It might not work via
> DMAengine.
DMA is enabled for MMC, and works OK on all of these devices.
A.
Since v2.6.22 or so there has been reports [1] about OMAP MMC being
broken on OMAP15XX based hardware (OMAP5910 and OMAP310). The breakage
seems to have been caused by commit 46a6730e3ff9 ("mmc-omap: Fix
omap to use MMC_POWER_ON") that changed clock enabling to be done
on MMC_POWER_ON. This can happen multiple times in a row, and on 15XX
the hardware doesn't seem to like it and the MMC just stops responding.
Fix by memorizing the power mode and do the init only when necessary.
Before the patch (on Palm TE):
mmc0: new SD card at address b368
mmcblk0: mmc0:b368 SDC 977 MiB
mmci-omap mmci-omap.0: command timeout (CMD18)
mmci-omap mmci-omap.0: command timeout (CMD13)
mmci-omap mmci-omap.0: command timeout (CMD13)
mmci-omap mmci-omap.0: command timeout (CMD12) [x 6]
mmci-omap mmci-omap.0: command timeout (CMD13) [x 6]
mmcblk0: error -110 requesting status
mmci-omap mmci-omap.0: command timeout (CMD8)
mmci-omap mmci-omap.0: command timeout (CMD18)
mmci-omap mmci-omap.0: command timeout (CMD13)
mmci-omap mmci-omap.0: command timeout (CMD13)
mmci-omap mmci-omap.0: command timeout (CMD12) [x 6]
mmci-omap mmci-omap.0: command timeout (CMD13) [x 6]
mmcblk0: error -110 requesting status
mmcblk0: recovery failed!
print_req_error: I/O error, dev mmcblk0, sector 0
Buffer I/O error on dev mmcblk0, logical block 0, async page read
mmcblk0: unable to read partition table
After the patch:
mmc0: new SD card at address b368
mmcblk0: mmc0:b368 SDC 977 MiB
mmcblk0: p1
The patch is based on a fix and analysis done by Ladislav Michl.
Tested on OMAP15XX/OMAP310 (Palm TE), OMAP1710 (Nokia 770)
and OMAP2420 (Nokia N810).
[1] https://marc.info/?t=123175197000003&r=1&w=2
Fixes: 46a6730e3ff9 ("mmc-omap: Fix omap to use MMC_POWER_ON")
Reported-by: Ladislav Michl <[email protected]>
Reported-by: Andrzej Zaborowski <[email protected]>
Tested-by: Ladislav Michl <[email protected]>
Acked-by: Tony Lindgren <[email protected]>
Signed-off-by: Aaro Koskinen <[email protected]>
---
v2: Corrected commit message: OMAP5912 => OMAP5910
Added Tested-by and Acked-by tags.
v1: https://marc.info/?t=154258870700045&r=1&w=2
drivers/mmc/host/omap.c | 11 +++++++++--
1 file changed, 9 insertions(+), 2 deletions(-)
diff --git a/drivers/mmc/host/omap.c b/drivers/mmc/host/omap.c
index adf32682f27a..c60a7625b1fa 100644
--- a/drivers/mmc/host/omap.c
+++ b/drivers/mmc/host/omap.c
@@ -104,6 +104,7 @@ struct mmc_omap_slot {
unsigned int vdd;
u16 saved_con;
u16 bus_mode;
+ u16 power_mode;
unsigned int fclk_freq;
struct tasklet_struct cover_tasklet;
@@ -1157,7 +1158,7 @@ static void mmc_omap_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
struct mmc_omap_slot *slot = mmc_priv(mmc);
struct mmc_omap_host *host = slot->host;
int i, dsor;
- int clk_enabled;
+ int clk_enabled, init_stream;
mmc_omap_select_slot(slot, 0);
@@ -1167,6 +1168,7 @@ static void mmc_omap_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
slot->vdd = ios->vdd;
clk_enabled = 0;
+ init_stream = 0;
switch (ios->power_mode) {
case MMC_POWER_OFF:
mmc_omap_set_power(slot, 0, ios->vdd);
@@ -1174,13 +1176,17 @@ static void mmc_omap_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
case MMC_POWER_UP:
/* Cannot touch dsor yet, just power up MMC */
mmc_omap_set_power(slot, 1, ios->vdd);
+ slot->power_mode = ios->power_mode;
goto exit;
case MMC_POWER_ON:
mmc_omap_fclk_enable(host, 1);
clk_enabled = 1;
dsor |= 1 << 11;
+ if (slot->power_mode != MMC_POWER_ON)
+ init_stream = 1;
break;
}
+ slot->power_mode = ios->power_mode;
if (slot->bus_mode != ios->bus_mode) {
if (slot->pdata->set_bus_mode != NULL)
@@ -1196,7 +1202,7 @@ static void mmc_omap_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
for (i = 0; i < 2; i++)
OMAP_MMC_WRITE(host, CON, dsor);
slot->saved_con = dsor;
- if (ios->power_mode == MMC_POWER_ON) {
+ if (init_stream) {
/* worst case at 400kHz, 80 cycles makes 200 microsecs */
int usecs = 250;
@@ -1234,6 +1240,7 @@ static int mmc_omap_new_slot(struct mmc_omap_host *host, int id)
slot->host = host;
slot->mmc = mmc;
slot->id = id;
+ slot->power_mode = MMC_POWER_UNDEFINED;
slot->pdata = &host->pdata->slots[id];
host->slots[id] = slot;
--
2.17.0
On Tue, 20 Nov 2018 at 00:14, Aaro Koskinen <[email protected]> wrote:
>
> Since v2.6.22 or so there has been reports [1] about OMAP MMC being
> broken on OMAP15XX based hardware (OMAP5910 and OMAP310). The breakage
> seems to have been caused by commit 46a6730e3ff9 ("mmc-omap: Fix
> omap to use MMC_POWER_ON") that changed clock enabling to be done
> on MMC_POWER_ON. This can happen multiple times in a row, and on 15XX
> the hardware doesn't seem to like it and the MMC just stops responding.
> Fix by memorizing the power mode and do the init only when necessary.
>
> Before the patch (on Palm TE):
>
> mmc0: new SD card at address b368
> mmcblk0: mmc0:b368 SDC 977 MiB
> mmci-omap mmci-omap.0: command timeout (CMD18)
> mmci-omap mmci-omap.0: command timeout (CMD13)
> mmci-omap mmci-omap.0: command timeout (CMD13)
> mmci-omap mmci-omap.0: command timeout (CMD12) [x 6]
> mmci-omap mmci-omap.0: command timeout (CMD13) [x 6]
> mmcblk0: error -110 requesting status
> mmci-omap mmci-omap.0: command timeout (CMD8)
> mmci-omap mmci-omap.0: command timeout (CMD18)
> mmci-omap mmci-omap.0: command timeout (CMD13)
> mmci-omap mmci-omap.0: command timeout (CMD13)
> mmci-omap mmci-omap.0: command timeout (CMD12) [x 6]
> mmci-omap mmci-omap.0: command timeout (CMD13) [x 6]
> mmcblk0: error -110 requesting status
> mmcblk0: recovery failed!
> print_req_error: I/O error, dev mmcblk0, sector 0
> Buffer I/O error on dev mmcblk0, logical block 0, async page read
> mmcblk0: unable to read partition table
>
> After the patch:
>
> mmc0: new SD card at address b368
> mmcblk0: mmc0:b368 SDC 977 MiB
> mmcblk0: p1
>
> The patch is based on a fix and analysis done by Ladislav Michl.
>
> Tested on OMAP15XX/OMAP310 (Palm TE), OMAP1710 (Nokia 770)
> and OMAP2420 (Nokia N810).
>
> [1] https://marc.info/?t=123175197000003&r=1&w=2
>
> Fixes: 46a6730e3ff9 ("mmc-omap: Fix omap to use MMC_POWER_ON")
> Reported-by: Ladislav Michl <[email protected]>
> Reported-by: Andrzej Zaborowski <[email protected]>
> Tested-by: Ladislav Michl <[email protected]>
> Acked-by: Tony Lindgren <[email protected]>
> Signed-off-by: Aaro Koskinen <[email protected]>
Applied for fixes and by adding a stable tag, thanks!
Kind regards
Uffe
> ---
>
> v2: Corrected commit message: OMAP5912 => OMAP5910
> Added Tested-by and Acked-by tags.
>
> v1: https://marc.info/?t=154258870700045&r=1&w=2
>
> drivers/mmc/host/omap.c | 11 +++++++++--
> 1 file changed, 9 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/mmc/host/omap.c b/drivers/mmc/host/omap.c
> index adf32682f27a..c60a7625b1fa 100644
> --- a/drivers/mmc/host/omap.c
> +++ b/drivers/mmc/host/omap.c
> @@ -104,6 +104,7 @@ struct mmc_omap_slot {
> unsigned int vdd;
> u16 saved_con;
> u16 bus_mode;
> + u16 power_mode;
> unsigned int fclk_freq;
>
> struct tasklet_struct cover_tasklet;
> @@ -1157,7 +1158,7 @@ static void mmc_omap_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
> struct mmc_omap_slot *slot = mmc_priv(mmc);
> struct mmc_omap_host *host = slot->host;
> int i, dsor;
> - int clk_enabled;
> + int clk_enabled, init_stream;
>
> mmc_omap_select_slot(slot, 0);
>
> @@ -1167,6 +1168,7 @@ static void mmc_omap_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
> slot->vdd = ios->vdd;
>
> clk_enabled = 0;
> + init_stream = 0;
> switch (ios->power_mode) {
> case MMC_POWER_OFF:
> mmc_omap_set_power(slot, 0, ios->vdd);
> @@ -1174,13 +1176,17 @@ static void mmc_omap_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
> case MMC_POWER_UP:
> /* Cannot touch dsor yet, just power up MMC */
> mmc_omap_set_power(slot, 1, ios->vdd);
> + slot->power_mode = ios->power_mode;
> goto exit;
> case MMC_POWER_ON:
> mmc_omap_fclk_enable(host, 1);
> clk_enabled = 1;
> dsor |= 1 << 11;
> + if (slot->power_mode != MMC_POWER_ON)
> + init_stream = 1;
> break;
> }
> + slot->power_mode = ios->power_mode;
>
> if (slot->bus_mode != ios->bus_mode) {
> if (slot->pdata->set_bus_mode != NULL)
> @@ -1196,7 +1202,7 @@ static void mmc_omap_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
> for (i = 0; i < 2; i++)
> OMAP_MMC_WRITE(host, CON, dsor);
> slot->saved_con = dsor;
> - if (ios->power_mode == MMC_POWER_ON) {
> + if (init_stream) {
> /* worst case at 400kHz, 80 cycles makes 200 microsecs */
> int usecs = 250;
>
> @@ -1234,6 +1240,7 @@ static int mmc_omap_new_slot(struct mmc_omap_host *host, int id)
> slot->host = host;
> slot->mmc = mmc;
> slot->id = id;
> + slot->power_mode = MMC_POWER_UNDEFINED;
> slot->pdata = &host->pdata->slots[id];
>
> host->slots[id] = slot;
> --
> 2.17.0
>