spi_setup() already call spi_set_cs() right after calling the
controller setup method, so there is no need for the bitbang driver to
do that. Because of this the chipselect() callback was confusingly
still called when CS is GPIO based.
Signed-off-by: Alban Bedel <[email protected]>
---
drivers/spi/spi-bitbang.c | 13 -------------
1 file changed, 13 deletions(-)
diff --git a/drivers/spi/spi-bitbang.c b/drivers/spi/spi-bitbang.c
index f29176000b8d..dd9a8c54a693 100644
--- a/drivers/spi/spi-bitbang.c
+++ b/drivers/spi/spi-bitbang.c
@@ -213,19 +213,6 @@ int spi_bitbang_setup(struct spi_device *spi)
dev_dbg(&spi->dev, "%s, %u nsec/bit\n", __func__, 2 * cs->nsecs);
- /* NOTE we _need_ to call chipselect() early, ideally with adapter
- * setup, unless the hardware defaults cooperate to avoid confusion
- * between normal (active low) and inverted chipselects.
- */
-
- /* deselect chip (low or high) */
- mutex_lock(&bitbang->lock);
- if (!bitbang->busy) {
- bitbang->chipselect(spi, BITBANG_CS_INACTIVE);
- ndelay(cs->nsecs);
- }
- mutex_unlock(&bitbang->lock);
-
return 0;
}
EXPORT_SYMBOL_GPL(spi_bitbang_setup);
--
2.19.1
First of all this callback was slightly misused to setup the clock
polarity at the beginning of a transfer. Beside being at the wrong
place, it is also useless as only SPI mode 1 is supported. Instead
just make sure the base value used for IOC is suitable to start a
transfer by clearing the clock and data bits during the controller
setup.
This also remove the last direct usage of the GPIO API, so we can
remove the direct dependency on GPIOLIB.
Signed-off-by: Alban Bedel <[email protected]>
---
drivers/spi/Kconfig | 2 +-
drivers/spi/spi-ath79.c | 40 +++++++++-------------------------------
2 files changed, 10 insertions(+), 32 deletions(-)
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index dc67eda1788a..128892c7e21e 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -63,7 +63,7 @@ config SPI_ALTERA
config SPI_ATH79
tristate "Atheros AR71XX/AR724X/AR913X SPI controller driver"
- depends on ATH79 && GPIOLIB
+ depends on ATH79
select SPI_BITBANG
help
This enables support for the SPI controller present on the
diff --git a/drivers/spi/spi-ath79.c b/drivers/spi/spi-ath79.c
index ed1068ac055f..edf695a359f4 100644
--- a/drivers/spi/spi-ath79.c
+++ b/drivers/spi/spi-ath79.c
@@ -21,7 +21,6 @@
#include <linux/spi/spi.h>
#include <linux/spi/spi_bitbang.h>
#include <linux/bitops.h>
-#include <linux/gpio/consumer.h>
#include <linux/clk.h>
#include <linux/err.h>
@@ -67,38 +66,14 @@ static void ath79_spi_chipselect(struct spi_device *spi, int is_active)
{
struct ath79_spi *sp = ath79_spidev_to_sp(spi);
int cs_high = (spi->mode & SPI_CS_HIGH) ? is_active : !is_active;
+ u32 cs_bit = AR71XX_SPI_IOC_CS(spi->chip_select);
- if (is_active) {
- /* set initial clock polarity */
- if (spi->mode & SPI_CPOL)
- sp->ioc_base |= AR71XX_SPI_IOC_CLK;
- else
- sp->ioc_base &= ~AR71XX_SPI_IOC_CLK;
-
- ath79_spi_wr(sp, AR71XX_SPI_REG_IOC, sp->ioc_base);
- }
-
- if (spi->cs_gpiod) {
- /*
- * SPI chipselect is normally active-low, but
- * inversion semantics are handled by gpiolib.
- *
- * FIXME: is this ever used? The driver doesn't
- * set SPI_MASTER_GPIO_SS so this callback should not
- * get called if a CS GPIO is found by the SPI core.
- */
- gpiod_set_value_cansleep(spi->cs_gpiod, is_active);
- } else {
- u32 cs_bit = AR71XX_SPI_IOC_CS(spi->chip_select);
-
- if (cs_high)
- sp->ioc_base |= cs_bit;
- else
- sp->ioc_base &= ~cs_bit;
-
- ath79_spi_wr(sp, AR71XX_SPI_REG_IOC, sp->ioc_base);
- }
+ if (cs_high)
+ sp->ioc_base |= cs_bit;
+ else
+ sp->ioc_base &= ~cs_bit;
+ ath79_spi_wr(sp, AR71XX_SPI_REG_IOC, sp->ioc_base);
}
static void ath79_spi_enable(struct ath79_spi *sp)
@@ -110,6 +85,9 @@ static void ath79_spi_enable(struct ath79_spi *sp)
sp->reg_ctrl = ath79_spi_rr(sp, AR71XX_SPI_REG_CTRL);
sp->ioc_base = ath79_spi_rr(sp, AR71XX_SPI_REG_IOC);
+ /* clear clk and mosi in the base state */
+ sp->ioc_base &= ~(AR71XX_SPI_IOC_DO | AR71XX_SPI_IOC_CLK);
+
/* TODO: setup speed? */
ath79_spi_wr(sp, AR71XX_SPI_REG_CTRL, 0x43);
}
--
2.19.1
The custom setup/cleanup routines included in the ath79 driver only
take care of setting the initial CS state. However that is already
handled by the bitbang code, so this code can be removed.
Signed-off-by: Alban Bedel <[email protected]>
---
drivers/spi/spi-ath79.c | 43 ++---------------------------------------
1 file changed, 2 insertions(+), 41 deletions(-)
diff --git a/drivers/spi/spi-ath79.c b/drivers/spi/spi-ath79.c
index 09c4fb7fcf7a..847f354ebef1 100644
--- a/drivers/spi/spi-ath79.c
+++ b/drivers/spi/spi-ath79.c
@@ -109,44 +109,6 @@ static void ath79_spi_disable(struct ath79_spi *sp)
ath79_spi_wr(sp, AR71XX_SPI_REG_FS, 0);
}
-static int ath79_spi_setup_cs(struct spi_device *spi)
-{
- struct ath79_spi *sp = ath79_spidev_to_sp(spi);
-
- if (!spi->cs_gpiod) {
- u32 cs_bit = AR71XX_SPI_IOC_CS(spi->chip_select);
-
- if (spi->mode & SPI_CS_HIGH)
- sp->ioc_base &= ~cs_bit;
- else
- sp->ioc_base |= cs_bit;
-
- ath79_spi_wr(sp, AR71XX_SPI_REG_IOC, sp->ioc_base);
- }
-
- return 0;
-}
-
-static int ath79_spi_setup(struct spi_device *spi)
-{
- int status = 0;
-
- if (!spi->controller_state) {
- status = ath79_spi_setup_cs(spi);
- if (status)
- return status;
- }
-
- status = spi_bitbang_setup(spi);
-
- return status;
-}
-
-static void ath79_spi_cleanup(struct spi_device *spi)
-{
- spi_bitbang_cleanup(spi);
-}
-
static u32 ath79_spi_txrx_mode0(struct spi_device *spi, unsigned int nsecs,
u32 word, u8 bits, unsigned flags)
{
@@ -199,8 +161,8 @@ static int ath79_spi_probe(struct platform_device *pdev)
master->use_gpio_descriptors = true;
master->bits_per_word_mask = SPI_BPW_RANGE_MASK(1, 32);
- master->setup = ath79_spi_setup;
- master->cleanup = ath79_spi_cleanup;
+ master->setup = spi_bitbang_setup;
+ master->cleanup = spi_bitbang_cleanup;
if (pdata) {
master->bus_num = pdata->bus_num;
master->num_chipselect = pdata->num_chipselect;
@@ -209,7 +171,6 @@ static int ath79_spi_probe(struct platform_device *pdev)
sp->bitbang.master = master;
sp->bitbang.chipselect = ath79_spi_chipselect;
sp->bitbang.txrx_word[SPI_MODE_0] = ath79_spi_txrx_mode0;
- sp->bitbang.setup_transfer = spi_bitbang_setup_transfer;
sp->bitbang.flags = SPI_CS_HIGH;
r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
--
2.19.1
Add myself as the maintainer for the ath79 SPI driver.
Signed-off-by: Alban Bedel <[email protected]>
---
MAINTAINERS | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index 71e2965fc656..a03ab41489cf 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2520,6 +2520,15 @@ S: Maintained
F: drivers/gpio/gpio-ath79.c
F: Documentation/devicetree/bindings/gpio/gpio-ath79.txt
+ATHEROS 71XX/9XXX SPI DRIVER
+M: Alban Bedel <[email protected]>
+W: https://github.com/AlbanBedel/linux
+T: git git://github.com/AlbanBedel/linux
+S: Maintained
+F: drivers/spi/spi-ath79.c
+F: include/linux/platform_data/spi-ath79.h
+F: Documentation/devicetree/bindings/spi/spi-ath79.txt
+
ATHEROS 71XX/9XXX USB PHY DRIVER
M: Alban Bedel <[email protected]>
W: https://github.com/AlbanBedel/linux
--
2.19.1
Several include are not needed, remove them to keep the list clean.
Signed-off-by: Alban Bedel <[email protected]>
---
drivers/spi/spi-ath79.c | 3 ---
1 file changed, 3 deletions(-)
diff --git a/drivers/spi/spi-ath79.c b/drivers/spi/spi-ath79.c
index 847f354ebef1..257acfb07819 100644
--- a/drivers/spi/spi-ath79.c
+++ b/drivers/spi/spi-ath79.c
@@ -12,15 +12,12 @@
*
*/
-#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/delay.h>
-#include <linux/spinlock.h>
#include <linux/platform_device.h>
#include <linux/io.h>
#include <linux/spi/spi.h>
#include <linux/spi/spi_bitbang.h>
-#include <linux/bitops.h>
#include <linux/clk.h>
#include <linux/err.h>
#include <linux/platform_data/spi-ath79.h>
--
2.19.1
On Wed, 2019-01-16 at 19:55 +0100, Alban Bedel wrote:
> Several include are not needed, remove them to keep the list clean.
[]
> diff --git a/drivers/spi/spi-ath79.c b/drivers/spi/spi-ath79.c
[]
> @@ -12,15 +12,12 @@
> *
> */
>
> -#include <linux/kernel.h>
I think it's not a good idea to remove kernel.h
just because module.h indirectly #includes it via
moduleparam.h
To allow building this driver in compile test we need to remove all
dependency on headers from arch/mips/include. To allow this we
explicitly define all the registers locally instead of using
ar71xx_regs.h and we move the platform data struct definition to
include/linux/platform_data/spi-ath79.h.
Signed-off-by: Alban Bedel <[email protected]>
---
arch/mips/ath79/dev-spi.h | 2 +-
drivers/spi/Kconfig | 2 +-
drivers/spi/spi-ath79.c | 15 ++++++++++++---
.../linux/platform_data/spi-ath79.h | 0
4 files changed, 14 insertions(+), 5 deletions(-)
rename arch/mips/include/asm/mach-ath79/ath79_spi_platform.h => include/linux/platform_data/spi-ath79.h (100%)
diff --git a/arch/mips/ath79/dev-spi.h b/arch/mips/ath79/dev-spi.h
index d732565ca736..6e15bc8651be 100644
--- a/arch/mips/ath79/dev-spi.h
+++ b/arch/mips/ath79/dev-spi.h
@@ -13,7 +13,7 @@
#define _ATH79_DEV_SPI_H
#include <linux/spi/spi.h>
-#include <asm/mach-ath79/ath79_spi_platform.h>
+#include <linux/platform_data/spi-ath79.h>
void ath79_register_spi(struct ath79_spi_platform_data *pdata,
struct spi_board_info const *info,
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 128892c7e21e..71d3d2d5e5d1 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -63,7 +63,7 @@ config SPI_ALTERA
config SPI_ATH79
tristate "Atheros AR71XX/AR724X/AR913X SPI controller driver"
- depends on ATH79
+ depends on ATH79 || COMPILE_TEST
select SPI_BITBANG
help
This enables support for the SPI controller present on the
diff --git a/drivers/spi/spi-ath79.c b/drivers/spi/spi-ath79.c
index edf695a359f4..09c4fb7fcf7a 100644
--- a/drivers/spi/spi-ath79.c
+++ b/drivers/spi/spi-ath79.c
@@ -23,15 +23,24 @@
#include <linux/bitops.h>
#include <linux/clk.h>
#include <linux/err.h>
-
-#include <asm/mach-ath79/ar71xx_regs.h>
-#include <asm/mach-ath79/ath79_spi_platform.h>
+#include <linux/platform_data/spi-ath79.h>
#define DRV_NAME "ath79-spi"
#define ATH79_SPI_RRW_DELAY_FACTOR 12000
#define MHZ (1000 * 1000)
+#define AR71XX_SPI_REG_FS 0x00 /* Function Select */
+#define AR71XX_SPI_REG_CTRL 0x04 /* SPI Control */
+#define AR71XX_SPI_REG_IOC 0x08 /* SPI I/O Control */
+#define AR71XX_SPI_REG_RDS 0x0c /* Read Data Shift */
+
+#define AR71XX_SPI_FS_GPIO BIT(0) /* Enable GPIO mode */
+
+#define AR71XX_SPI_IOC_DO BIT(0) /* Data Out pin */
+#define AR71XX_SPI_IOC_CLK BIT(8) /* CLK pin */
+#define AR71XX_SPI_IOC_CS(n) BIT(16 + (n))
+
struct ath79_spi {
struct spi_bitbang bitbang;
u32 ioc_base;
diff --git a/arch/mips/include/asm/mach-ath79/ath79_spi_platform.h b/include/linux/platform_data/spi-ath79.h
similarity index 100%
rename from arch/mips/include/asm/mach-ath79/ath79_spi_platform.h
rename to include/linux/platform_data/spi-ath79.h
--
2.19.1
The patch
spi: ath79: Simplify ath79_spi_chipselect()
has been applied to the spi tree at
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git
All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying
to this mail.
Thanks,
Mark
From 797622d7a3ab5192ff575288bdbec15c3a006280 Mon Sep 17 00:00:00 2001
From: Alban Bedel <[email protected]>
Date: Wed, 16 Jan 2019 19:55:45 +0100
Subject: [PATCH] spi: ath79: Simplify ath79_spi_chipselect()
First of all this callback was slightly misused to setup the clock
polarity at the beginning of a transfer. Beside being at the wrong
place, it is also useless as only SPI mode 1 is supported. Instead
just make sure the base value used for IOC is suitable to start a
transfer by clearing the clock and data bits during the controller
setup.
This also remove the last direct usage of the GPIO API, so we can
remove the direct dependency on GPIOLIB.
Signed-off-by: Alban Bedel <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
---
drivers/spi/Kconfig | 2 +-
drivers/spi/spi-ath79.c | 40 +++++++++-------------------------------
2 files changed, 10 insertions(+), 32 deletions(-)
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index dc67eda1788a..128892c7e21e 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -63,7 +63,7 @@ config SPI_ALTERA
config SPI_ATH79
tristate "Atheros AR71XX/AR724X/AR913X SPI controller driver"
- depends on ATH79 && GPIOLIB
+ depends on ATH79
select SPI_BITBANG
help
This enables support for the SPI controller present on the
diff --git a/drivers/spi/spi-ath79.c b/drivers/spi/spi-ath79.c
index ed1068ac055f..edf695a359f4 100644
--- a/drivers/spi/spi-ath79.c
+++ b/drivers/spi/spi-ath79.c
@@ -21,7 +21,6 @@
#include <linux/spi/spi.h>
#include <linux/spi/spi_bitbang.h>
#include <linux/bitops.h>
-#include <linux/gpio/consumer.h>
#include <linux/clk.h>
#include <linux/err.h>
@@ -67,38 +66,14 @@ static void ath79_spi_chipselect(struct spi_device *spi, int is_active)
{
struct ath79_spi *sp = ath79_spidev_to_sp(spi);
int cs_high = (spi->mode & SPI_CS_HIGH) ? is_active : !is_active;
+ u32 cs_bit = AR71XX_SPI_IOC_CS(spi->chip_select);
- if (is_active) {
- /* set initial clock polarity */
- if (spi->mode & SPI_CPOL)
- sp->ioc_base |= AR71XX_SPI_IOC_CLK;
- else
- sp->ioc_base &= ~AR71XX_SPI_IOC_CLK;
-
- ath79_spi_wr(sp, AR71XX_SPI_REG_IOC, sp->ioc_base);
- }
-
- if (spi->cs_gpiod) {
- /*
- * SPI chipselect is normally active-low, but
- * inversion semantics are handled by gpiolib.
- *
- * FIXME: is this ever used? The driver doesn't
- * set SPI_MASTER_GPIO_SS so this callback should not
- * get called if a CS GPIO is found by the SPI core.
- */
- gpiod_set_value_cansleep(spi->cs_gpiod, is_active);
- } else {
- u32 cs_bit = AR71XX_SPI_IOC_CS(spi->chip_select);
-
- if (cs_high)
- sp->ioc_base |= cs_bit;
- else
- sp->ioc_base &= ~cs_bit;
-
- ath79_spi_wr(sp, AR71XX_SPI_REG_IOC, sp->ioc_base);
- }
+ if (cs_high)
+ sp->ioc_base |= cs_bit;
+ else
+ sp->ioc_base &= ~cs_bit;
+ ath79_spi_wr(sp, AR71XX_SPI_REG_IOC, sp->ioc_base);
}
static void ath79_spi_enable(struct ath79_spi *sp)
@@ -110,6 +85,9 @@ static void ath79_spi_enable(struct ath79_spi *sp)
sp->reg_ctrl = ath79_spi_rr(sp, AR71XX_SPI_REG_CTRL);
sp->ioc_base = ath79_spi_rr(sp, AR71XX_SPI_REG_IOC);
+ /* clear clk and mosi in the base state */
+ sp->ioc_base &= ~(AR71XX_SPI_IOC_DO | AR71XX_SPI_IOC_CLK);
+
/* TODO: setup speed? */
ath79_spi_wr(sp, AR71XX_SPI_REG_CTRL, 0x43);
}
--
2.20.1
The patch
spi: ath79: Enable support for compile test
has been applied to the spi tree at
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git
All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying
to this mail.
Thanks,
Mark
From b172fd0c898022c47161a99cb40be5304b0d3fd0 Mon Sep 17 00:00:00 2001
From: Alban Bedel <[email protected]>
Date: Wed, 16 Jan 2019 19:55:46 +0100
Subject: [PATCH] spi: ath79: Enable support for compile test
To allow building this driver in compile test we need to remove all
dependency on headers from arch/mips/include. To allow this we
explicitly define all the registers locally instead of using
ar71xx_regs.h and we move the platform data struct definition to
include/linux/platform_data/spi-ath79.h.
Signed-off-by: Alban Bedel <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
---
arch/mips/ath79/dev-spi.h | 2 +-
drivers/spi/Kconfig | 2 +-
drivers/spi/spi-ath79.c | 15 ++++++++++++---
.../linux/platform_data/spi-ath79.h | 0
4 files changed, 14 insertions(+), 5 deletions(-)
rename arch/mips/include/asm/mach-ath79/ath79_spi_platform.h => include/linux/platform_data/spi-ath79.h (100%)
diff --git a/arch/mips/ath79/dev-spi.h b/arch/mips/ath79/dev-spi.h
index d732565ca736..6e15bc8651be 100644
--- a/arch/mips/ath79/dev-spi.h
+++ b/arch/mips/ath79/dev-spi.h
@@ -13,7 +13,7 @@
#define _ATH79_DEV_SPI_H
#include <linux/spi/spi.h>
-#include <asm/mach-ath79/ath79_spi_platform.h>
+#include <linux/platform_data/spi-ath79.h>
void ath79_register_spi(struct ath79_spi_platform_data *pdata,
struct spi_board_info const *info,
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 128892c7e21e..71d3d2d5e5d1 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -63,7 +63,7 @@ config SPI_ALTERA
config SPI_ATH79
tristate "Atheros AR71XX/AR724X/AR913X SPI controller driver"
- depends on ATH79
+ depends on ATH79 || COMPILE_TEST
select SPI_BITBANG
help
This enables support for the SPI controller present on the
diff --git a/drivers/spi/spi-ath79.c b/drivers/spi/spi-ath79.c
index edf695a359f4..09c4fb7fcf7a 100644
--- a/drivers/spi/spi-ath79.c
+++ b/drivers/spi/spi-ath79.c
@@ -23,15 +23,24 @@
#include <linux/bitops.h>
#include <linux/clk.h>
#include <linux/err.h>
-
-#include <asm/mach-ath79/ar71xx_regs.h>
-#include <asm/mach-ath79/ath79_spi_platform.h>
+#include <linux/platform_data/spi-ath79.h>
#define DRV_NAME "ath79-spi"
#define ATH79_SPI_RRW_DELAY_FACTOR 12000
#define MHZ (1000 * 1000)
+#define AR71XX_SPI_REG_FS 0x00 /* Function Select */
+#define AR71XX_SPI_REG_CTRL 0x04 /* SPI Control */
+#define AR71XX_SPI_REG_IOC 0x08 /* SPI I/O Control */
+#define AR71XX_SPI_REG_RDS 0x0c /* Read Data Shift */
+
+#define AR71XX_SPI_FS_GPIO BIT(0) /* Enable GPIO mode */
+
+#define AR71XX_SPI_IOC_DO BIT(0) /* Data Out pin */
+#define AR71XX_SPI_IOC_CLK BIT(8) /* CLK pin */
+#define AR71XX_SPI_IOC_CS(n) BIT(16 + (n))
+
struct ath79_spi {
struct spi_bitbang bitbang;
u32 ioc_base;
diff --git a/arch/mips/include/asm/mach-ath79/ath79_spi_platform.h b/include/linux/platform_data/spi-ath79.h
similarity index 100%
rename from arch/mips/include/asm/mach-ath79/ath79_spi_platform.h
rename to include/linux/platform_data/spi-ath79.h
--
2.20.1
The patch
spi: ath79: Remove now useless code
has been applied to the spi tree at
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git
All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying
to this mail.
Thanks,
Mark
From f1b2c1c84f7f04d91749e1550f24510c6b6eac73 Mon Sep 17 00:00:00 2001
From: Alban Bedel <[email protected]>
Date: Wed, 16 Jan 2019 19:55:47 +0100
Subject: [PATCH] spi: ath79: Remove now useless code
The custom setup/cleanup routines included in the ath79 driver only
take care of setting the initial CS state. However that is already
handled by the bitbang code, so this code can be removed.
Signed-off-by: Alban Bedel <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
---
drivers/spi/spi-ath79.c | 43 ++---------------------------------------
1 file changed, 2 insertions(+), 41 deletions(-)
diff --git a/drivers/spi/spi-ath79.c b/drivers/spi/spi-ath79.c
index 09c4fb7fcf7a..847f354ebef1 100644
--- a/drivers/spi/spi-ath79.c
+++ b/drivers/spi/spi-ath79.c
@@ -109,44 +109,6 @@ static void ath79_spi_disable(struct ath79_spi *sp)
ath79_spi_wr(sp, AR71XX_SPI_REG_FS, 0);
}
-static int ath79_spi_setup_cs(struct spi_device *spi)
-{
- struct ath79_spi *sp = ath79_spidev_to_sp(spi);
-
- if (!spi->cs_gpiod) {
- u32 cs_bit = AR71XX_SPI_IOC_CS(spi->chip_select);
-
- if (spi->mode & SPI_CS_HIGH)
- sp->ioc_base &= ~cs_bit;
- else
- sp->ioc_base |= cs_bit;
-
- ath79_spi_wr(sp, AR71XX_SPI_REG_IOC, sp->ioc_base);
- }
-
- return 0;
-}
-
-static int ath79_spi_setup(struct spi_device *spi)
-{
- int status = 0;
-
- if (!spi->controller_state) {
- status = ath79_spi_setup_cs(spi);
- if (status)
- return status;
- }
-
- status = spi_bitbang_setup(spi);
-
- return status;
-}
-
-static void ath79_spi_cleanup(struct spi_device *spi)
-{
- spi_bitbang_cleanup(spi);
-}
-
static u32 ath79_spi_txrx_mode0(struct spi_device *spi, unsigned int nsecs,
u32 word, u8 bits, unsigned flags)
{
@@ -199,8 +161,8 @@ static int ath79_spi_probe(struct platform_device *pdev)
master->use_gpio_descriptors = true;
master->bits_per_word_mask = SPI_BPW_RANGE_MASK(1, 32);
- master->setup = ath79_spi_setup;
- master->cleanup = ath79_spi_cleanup;
+ master->setup = spi_bitbang_setup;
+ master->cleanup = spi_bitbang_cleanup;
if (pdata) {
master->bus_num = pdata->bus_num;
master->num_chipselect = pdata->num_chipselect;
@@ -209,7 +171,6 @@ static int ath79_spi_probe(struct platform_device *pdev)
sp->bitbang.master = master;
sp->bitbang.chipselect = ath79_spi_chipselect;
sp->bitbang.txrx_word[SPI_MODE_0] = ath79_spi_txrx_mode0;
- sp->bitbang.setup_transfer = spi_bitbang_setup_transfer;
sp->bitbang.flags = SPI_CS_HIGH;
r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
--
2.20.1
The patch
spi: bitbang: Don't call chipselect() in spi_bitbang_setup()
has been applied to the spi tree at
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git
All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying
to this mail.
Thanks,
Mark
From a666f2619a97ab9264d3b06055a336b3ee75c108 Mon Sep 17 00:00:00 2001
From: Alban Bedel <[email protected]>
Date: Wed, 16 Jan 2019 19:55:44 +0100
Subject: [PATCH] spi: bitbang: Don't call chipselect() in spi_bitbang_setup()
spi_setup() already call spi_set_cs() right after calling the
controller setup method, so there is no need for the bitbang driver to
do that. Because of this the chipselect() callback was confusingly
still called when CS is GPIO based.
Signed-off-by: Alban Bedel <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
---
drivers/spi/spi-bitbang.c | 13 -------------
1 file changed, 13 deletions(-)
diff --git a/drivers/spi/spi-bitbang.c b/drivers/spi/spi-bitbang.c
index f29176000b8d..dd9a8c54a693 100644
--- a/drivers/spi/spi-bitbang.c
+++ b/drivers/spi/spi-bitbang.c
@@ -213,19 +213,6 @@ int spi_bitbang_setup(struct spi_device *spi)
dev_dbg(&spi->dev, "%s, %u nsec/bit\n", __func__, 2 * cs->nsecs);
- /* NOTE we _need_ to call chipselect() early, ideally with adapter
- * setup, unless the hardware defaults cooperate to avoid confusion
- * between normal (active low) and inverted chipselects.
- */
-
- /* deselect chip (low or high) */
- mutex_lock(&bitbang->lock);
- if (!bitbang->busy) {
- bitbang->chipselect(spi, BITBANG_CS_INACTIVE);
- ndelay(cs->nsecs);
- }
- mutex_unlock(&bitbang->lock);
-
return 0;
}
EXPORT_SYMBOL_GPL(spi_bitbang_setup);
--
2.20.1