From: Nikhil Badola <[email protected]>
Set USB_EN bit to select ULPI phy for USB controller version 2.5
Signed-off-by: Nikhil Badola <[email protected]>
Signed-off-by: yinbo.zhu <[email protected]>
---
drivers/usb/host/ehci-fsl.c | 6 ++++++
1 files changed, 6 insertions(+), 0 deletions(-)
diff --git a/drivers/usb/host/ehci-fsl.c b/drivers/usb/host/ehci-fsl.c
index 0a9fd20..71c4661 100644
--- a/drivers/usb/host/ehci-fsl.c
+++ b/drivers/usb/host/ehci-fsl.c
@@ -118,6 +118,12 @@ static int fsl_ehci_drv_probe(struct platform_device *pdev)
clrsetbits_be32(hcd->regs + FSL_SOC_USB_CTRL,
CONTROL_REGISTER_W1C_MASK, 0x4);
+ /* Set USB_EN bit to select ULPI phy for USB controller version 2.5 */
+ if (pdata->controller_ver == FSL_USB_VER_2_5 &&
+ pdata->phy_mode == FSL_USB2_PHY_ULPI)
+ iowrite32be(USB_CTRL_USB_EN, hcd->regs + FSL_SOC_USB_CTRL);
+
+
/*
* Enable UTMI phy and program PTS field in UTMI mode before asserting
* controller reset for USB Controller version 2.5
--
1.7.1
On Mon, Jan 21, 2019 at 11:13:01AM +0800, Yinbo Zhu wrote:
> From: yinbo.zhu <[email protected]>
This should read:
From: Yinbo Zhu <[email protected]>
right?
> USB erratum-A006918 workaround tries to start internal PHY inside
> uboot (when PLL fails to lock). However, if the workaround also
> fails, then USB initialization is also stopped inside Linux.
> Erratum-A006918 workaround failure creates "fsl,erratum_a006918"
> node in device-tree. Presence of this node in device-tree is
> used to stop USB controller initialization in Linux
>
> Signed-off-by: Ramneek Mehresh <[email protected]>
> Signed-off-by: Suresh Gupta <[email protected]>
> Signed-off-by: yinbo.zhu <[email protected]>
Same here, don't use your email alias as your signed-off-by name.
thanks,
greg k-h
On Mon, Jan 21, 2019 at 11:13:00AM +0800, Yinbo Zhu wrote:
> From: Suresh Gupta <[email protected]>
>
> PHY_CLK_VALID bit for UTMI PHY in USBDR does not set even
> if PHY is providing valid clock. Workaround for this
> involves resetting of PHY and check PHY_CLK_VALID bit
> multiple times. If PHY_CLK_VALID bit is still not set even
> after 5 retries, it would be safe to deaclare that PHY
> clock is not available.
> This erratum is applicable for USBDR less then ver 2.4.
>
> Signed-off-by: Suresh Gupta <[email protected]>
> Signed-off-by: yinbo.zhu <[email protected]>
Same issue here with the signed-off-by name. For all of these patches.
Please fix up and resend the whole series.
thanks,
greg k-h
From: Nikhil Badola <[email protected]>
Remove USB errata checking code from driver. Applicability of erratum
is retrieved by reading corresponding property in device tree.
This property is written during device tree fixup.
Signed-off-by: Ramneek Mehresh <[email protected]>
Signed-off-by: Nikhil Badola <[email protected]>
Signed-off-by: yinbo.zhu <[email protected]>
---
drivers/usb/host/ehci-fsl.c | 7 +------
drivers/usb/host/fsl-mph-dr-of.c | 9 ++++-----
2 files changed, 5 insertions(+), 11 deletions(-)
diff --git a/drivers/usb/host/ehci-fsl.c b/drivers/usb/host/ehci-fsl.c
index 6884130..c71680e 100644
--- a/drivers/usb/host/ehci-fsl.c
+++ b/drivers/usb/host/ehci-fsl.c
@@ -310,14 +310,9 @@ static int ehci_fsl_usb_setup(struct ehci_hcd *ehci)
return -EINVAL;
if (pdata->operating_mode == FSL_USB2_MPH_HOST) {
- unsigned int chip, rev, svr;
-
- svr = mfspr(SPRN_SVR);
- chip = svr >> 16;
- rev = (svr >> 4) & 0xf;
/* Deal with USB Erratum #14 on MPC834x Rev 1.0 & 1.1 chips */
- if ((rev == 1) && (chip >= 0x8050) && (chip <= 0x8055))
+ if (pdata->has_fsl_erratum_14 == 1)
ehci->has_fsl_port_bug = 1;
if (pdata->port_enables & FSL_USB2_PORT0_ENABLED)
diff --git a/drivers/usb/host/fsl-mph-dr-of.c b/drivers/usb/host/fsl-mph-dr-of.c
index 7e07701..ae8f60f 100644
--- a/drivers/usb/host/fsl-mph-dr-of.c
+++ b/drivers/usb/host/fsl-mph-dr-of.c
@@ -224,11 +224,10 @@ static int fsl_usb2_mph_dr_of_probe(struct platform_device *ofdev)
of_property_read_bool(np, "fsl,usb-erratum-a005275");
pdata->has_fsl_erratum_a005697 =
of_property_read_bool(np, "fsl,usb_erratum-a005697");
-
- if (of_get_property(np, "fsl,erratum_a006918", NULL))
- pdata->has_fsl_erratum_a006918 = 1;
- else
- pdata->has_fsl_erratum_a006918 = 0;
+ pdata->has_fsl_erratum_a006918 =
+ of_property_read_bool(np, "fsl,usb_erratum-a006918");
+ pdata->has_fsl_erratum_14 =
+ of_property_read_bool(np, "fsl,usb_erratum-14");
/*
* Determine whether phy_clk_valid needs to be checked
--
1.7.1
From: yinbo.zhu <[email protected]>
USB erratum-A006918 workaround tries to start internal PHY inside
uboot (when PLL fails to lock). However, if the workaround also
fails, then USB initialization is also stopped inside Linux.
Erratum-A006918 workaround failure creates "fsl,erratum_a006918"
node in device-tree. Presence of this node in device-tree is
used to stop USB controller initialization in Linux
Signed-off-by: Ramneek Mehresh <[email protected]>
Signed-off-by: Suresh Gupta <[email protected]>
Signed-off-by: yinbo.zhu <[email protected]>
---
drivers/usb/host/ehci-fsl.c | 5 +++++
drivers/usb/host/fsl-mph-dr-of.c | 5 +++++
2 files changed, 10 insertions(+), 0 deletions(-)
diff --git a/drivers/usb/host/ehci-fsl.c b/drivers/usb/host/ehci-fsl.c
index a28ec1e..6884130 100644
--- a/drivers/usb/host/ehci-fsl.c
+++ b/drivers/usb/host/ehci-fsl.c
@@ -224,6 +224,11 @@ static int ehci_fsl_setup_phy(struct usb_hcd *hcd,
portsc |= PORT_PTS_PTW;
/* fall through */
case FSL_USB2_PHY_UTMI:
+ if (pdata->has_fsl_erratum_a006918) {
+ pr_warn("fsl-ehci: USB PHY clock invalid\n");
+ return -EINVAL;
+ }
+
case FSL_USB2_PHY_UTMI_DUAL:
/* PHY_CLK_VALID bit is de-featured from all controller
* versions below 2.4 and is to be checked only for
diff --git a/drivers/usb/host/fsl-mph-dr-of.c b/drivers/usb/host/fsl-mph-dr-of.c
index 677f9d5..7e07701 100644
--- a/drivers/usb/host/fsl-mph-dr-of.c
+++ b/drivers/usb/host/fsl-mph-dr-of.c
@@ -225,6 +225,11 @@ static int fsl_usb2_mph_dr_of_probe(struct platform_device *ofdev)
pdata->has_fsl_erratum_a005697 =
of_property_read_bool(np, "fsl,usb_erratum-a005697");
+ if (of_get_property(np, "fsl,erratum_a006918", NULL))
+ pdata->has_fsl_erratum_a006918 = 1;
+ else
+ pdata->has_fsl_erratum_a006918 = 0;
+
/*
* Determine whether phy_clk_valid needs to be checked
* by reading property in device tree
--
1.7.1
This patch is to add member has_fsl_erratum_a006918 in platform data
Signed-off-by: Yinbo Zhu <[email protected]>
---
include/linux/fsl_devices.h | 1 +
1 files changed, 1 insertions(+), 0 deletions(-)
diff --git a/include/linux/fsl_devices.h b/include/linux/fsl_devices.h
index 60cef82..7ea53c8 100644
--- a/include/linux/fsl_devices.h
+++ b/include/linux/fsl_devices.h
@@ -101,6 +101,7 @@ struct fsl_usb2_platform_data {
unsigned has_fsl_erratum_a007792:1;
unsigned has_fsl_erratum_a005275:1;
unsigned has_fsl_erratum_a005697:1;
+ unsigned has_fsl_erratum_a006918:1;
unsigned check_phy_clk_valid:1;
/* register save area for suspend/resume */
--
1.7.1
This patch is to add member has_fsl_erratum_14 in platform data
Signed-off-by: Yinbo Zhu <[email protected]>
---
include/linux/fsl_devices.h | 1 +
1 files changed, 1 insertions(+), 0 deletions(-)
diff --git a/include/linux/fsl_devices.h b/include/linux/fsl_devices.h
index 7ea53c8..5c21a3a 100644
--- a/include/linux/fsl_devices.h
+++ b/include/linux/fsl_devices.h
@@ -102,6 +102,7 @@ struct fsl_usb2_platform_data {
unsigned has_fsl_erratum_a005275:1;
unsigned has_fsl_erratum_a005697:1;
unsigned has_fsl_erratum_a006918:1;
+ unsigned has_fsl_erratum_14:1;
unsigned check_phy_clk_valid:1;
/* register save area for suspend/resume */
--
1.7.1
From: Suresh Gupta <[email protected]>
PHY_CLK_VALID bit for UTMI PHY in USBDR does not set even
if PHY is providing valid clock. Workaround for this
involves resetting of PHY and check PHY_CLK_VALID bit
multiple times. If PHY_CLK_VALID bit is still not set even
after 5 retries, it would be safe to deaclare that PHY
clock is not available.
This erratum is applicable for USBDR less then ver 2.4.
Signed-off-by: Suresh Gupta <[email protected]>
Signed-off-by: yinbo.zhu <[email protected]>
---
drivers/usb/host/ehci-fsl.c | 37 ++++++++++++++++++++++++++-----------
drivers/usb/host/ehci-fsl.h | 3 +++
2 files changed, 29 insertions(+), 11 deletions(-)
diff --git a/drivers/usb/host/ehci-fsl.c b/drivers/usb/host/ehci-fsl.c
index 71c4661..a28ec1e 100644
--- a/drivers/usb/host/ehci-fsl.c
+++ b/drivers/usb/host/ehci-fsl.c
@@ -176,6 +176,17 @@ static int fsl_ehci_drv_probe(struct platform_device *pdev)
return retval;
}
+static bool usb_phy_clk_valid(struct usb_hcd *hcd)
+{
+ void __iomem *non_ehci = hcd->regs;
+ bool ret = true;
+
+ if (!(in_be32(non_ehci + FSL_SOC_USB_CTRL) & PHY_CLK_VALID))
+ ret = false;
+
+ return ret;
+}
+
static int ehci_fsl_setup_phy(struct usb_hcd *hcd,
enum fsl_usb2_phy_modes phy_mode,
unsigned int port_offset)
@@ -214,6 +225,16 @@ static int ehci_fsl_setup_phy(struct usb_hcd *hcd,
/* fall through */
case FSL_USB2_PHY_UTMI:
case FSL_USB2_PHY_UTMI_DUAL:
+ /* PHY_CLK_VALID bit is de-featured from all controller
+ * versions below 2.4 and is to be checked only for
+ * internal UTMI phy
+ */
+ if (pdata->controller_ver > FSL_USB_VER_2_4 &&
+ pdata->have_sysif_regs && !usb_phy_clk_valid(hcd)) {
+ pr_err("fsl-ehci: USB PHY clock invalid\n");
+ return -EINVAL;
+ }
+
if (pdata->have_sysif_regs && pdata->controller_ver) {
/* controller version 1.6 or above */
clrsetbits_be32(non_ehci + FSL_SOC_USB_CTRL,
@@ -232,17 +253,11 @@ static int ehci_fsl_setup_phy(struct usb_hcd *hcd,
break;
}
- /*
- * check PHY_CLK_VALID to determine phy clock presence before writing
- * to portsc
- */
- if (pdata->check_phy_clk_valid) {
- if (!(ioread32be(non_ehci + FSL_SOC_USB_CTRL) &
- PHY_CLK_VALID)) {
- dev_warn(hcd->self.controller,
- "USB PHY clock invalid\n");
- return -EINVAL;
- }
+ if (pdata->have_sysif_regs &&
+ pdata->controller_ver > FSL_USB_VER_1_6 &&
+ !usb_phy_clk_valid(hcd)) {
+ dev_warn(hcd->self.controller, "USB PHY clock invalid\n");
+ return -EINVAL;
}
ehci_writel(ehci, portsc, &ehci->regs->port_status[port_offset]);
diff --git a/drivers/usb/host/ehci-fsl.h b/drivers/usb/host/ehci-fsl.h
index cbc4220..9d18c6e 100644
--- a/drivers/usb/host/ehci-fsl.h
+++ b/drivers/usb/host/ehci-fsl.h
@@ -50,4 +50,7 @@
#define UTMI_PHY_EN (1<<9)
#define ULPI_PHY_CLK_SEL (1<<10)
#define PHY_CLK_VALID (1<<17)
+
+/* Retry count for checking UTMI PHY CLK validity */
+#define UTMI_PHY_CLK_VALID_CHK_RETRY 5
#endif /* _EHCI_FSL_H */
--
1.7.1
Hello!
On 21.01.2019 6:13, Yinbo Zhu wrote:
> From: yinbo.zhu <[email protected]>
>
> USB erratum-A006918 workaround tries to start internal PHY inside
> uboot (when PLL fails to lock). However, if the workaround also
> fails, then USB initialization is also stopped inside Linux.
> Erratum-A006918 workaround failure creates "fsl,erratum_a006918"
> node in device-tree. Presence of this node in device-tree is
> used to stop USB controller initialization in Linux
>
> Signed-off-by: Ramneek Mehresh <[email protected]>
> Signed-off-by: Suresh Gupta <[email protected]>
> Signed-off-by: yinbo.zhu <[email protected]>
> ---
> drivers/usb/host/ehci-fsl.c | 5 +++++
> drivers/usb/host/fsl-mph-dr-of.c | 5 +++++
> 2 files changed, 10 insertions(+), 0 deletions(-)
>
> diff --git a/drivers/usb/host/ehci-fsl.c b/drivers/usb/host/ehci-fsl.c
> index a28ec1e..6884130 100644
> --- a/drivers/usb/host/ehci-fsl.c
> +++ b/drivers/usb/host/ehci-fsl.c
> @@ -224,6 +224,11 @@ static int ehci_fsl_setup_phy(struct usb_hcd *hcd,
> portsc |= PORT_PTS_PTW;
> /* fall through */
> case FSL_USB2_PHY_UTMI:
> + if (pdata->has_fsl_erratum_a006918) {
> + pr_warn("fsl-ehci: USB PHY clock invalid\n");
> + return -EINVAL;
> + }
> +
> case FSL_USB2_PHY_UTMI_DUAL:
> /* PHY_CLK_VALID bit is de-featured from all controller
> * versions below 2.4 and is to be checked only for
> diff --git a/drivers/usb/host/fsl-mph-dr-of.c b/drivers/usb/host/fsl-mph-dr-of.c
> index 677f9d5..7e07701 100644
> --- a/drivers/usb/host/fsl-mph-dr-of.c
> +++ b/drivers/usb/host/fsl-mph-dr-of.c
> @@ -225,6 +225,11 @@ static int fsl_usb2_mph_dr_of_probe(struct platform_device *ofdev)
> pdata->has_fsl_erratum_a005697 =
> of_property_read_bool(np, "fsl,usb_erratum-a005697");
>
> + if (of_get_property(np, "fsl,erratum_a006918", NULL))
of_property_read_bool() perhaps?
> + pdata->has_fsl_erratum_a006918 = 1;
> + else
> + pdata->has_fsl_erratum_a006918 = 0;
> +
> /*
> * Determine whether phy_clk_valid needs to be checked
> * by reading property in device tree
MBR, Sergei
-----Original Message-----
From: Sergei Shtylyov [mailto:[email protected]]
Sent: 2019年1月21日 16:17
To: Yinbo Zhu <[email protected]>; Alan Stern <[email protected]>
Cc: Xiaobo Xie <[email protected]>; Jerry Huang <[email protected]>; Ran Wang <[email protected]>; Greg Kroah-Hartman <[email protected]>; Ramneek Mehresh <[email protected]>; Nikhil Badola <[email protected]>; Suresh Gupta <[email protected]>; [email protected]; [email protected]
Subject: Re: [PATCH v1 3/6] usb: host: Stops USB controller init if PLL fails to lock
>Hello!
> On 21.01.2019 6:13, Yinbo Zhu wrote:
> From: yinbo.zhu <[email protected]>
>
> USB erratum-A006918 workaround tries to start internal PHY inside
> uboot (when PLL fails to lock). However, if the workaround also fails,
> then USB initialization is also stopped inside Linux.
> Erratum-A006918 workaround failure creates "fsl,erratum_a006918"
> node in device-tree. Presence of this node in device-tree is used to
> stop USB controller initialization in Linux
>
> Signed-off-by: Ramneek Mehresh <[email protected]>
> Signed-off-by: Suresh Gupta <[email protected]>
> Signed-off-by: yinbo.zhu <[email protected]>
> ---
> drivers/usb/host/ehci-fsl.c | 5 +++++
> drivers/usb/host/fsl-mph-dr-of.c | 5 +++++
> 2 files changed, 10 insertions(+), 0 deletions(-)
>
> diff --git a/drivers/usb/host/ehci-fsl.c b/drivers/usb/host/ehci-fsl.c
> index a28ec1e..6884130 100644
> --- a/drivers/usb/host/ehci-fsl.c
> +++ b/drivers/usb/host/ehci-fsl.c
> @@ -224,6 +224,11 @@ static int ehci_fsl_setup_phy(struct usb_hcd *hcd,
> portsc |= PORT_PTS_PTW;
> /* fall through */
> case FSL_USB2_PHY_UTMI:
> + if (pdata->has_fsl_erratum_a006918) {
> + pr_warn("fsl-ehci: USB PHY clock invalid\n");
> + return -EINVAL;
> + }
> +
> case FSL_USB2_PHY_UTMI_DUAL:
> /* PHY_CLK_VALID bit is de-featured from all controller
> * versions below 2.4 and is to be checked only for diff --git
> a/drivers/usb/host/fsl-mph-dr-of.c b/drivers/usb/host/fsl-mph-dr-of.c
> index 677f9d5..7e07701 100644
> --- a/drivers/usb/host/fsl-mph-dr-of.c
> +++ b/drivers/usb/host/fsl-mph-dr-of.c
> @@ -225,6 +225,11 @@ static int fsl_usb2_mph_dr_of_probe(struct platform_device *ofdev)
> pdata->has_fsl_erratum_a005697 =
> of_property_read_bool(np, "fsl,usb_erratum-a005697");
>
> + if (of_get_property(np, "fsl,erratum_a006918", NULL))
> of_property_read_bool() perhaps?
Hi Sergei,
[PATCH v1 6/6] had modified it as this string format,
Please you note.
MBR, Yinbo
> + pdata->has_fsl_erratum_a006918 = 1;
> + else
> + pdata->has_fsl_erratum_a006918 = 0;
> +
> /*
> * Determine whether phy_clk_valid needs to be checked
> * by reading property in device tree
> MBR, Sergei