2019-01-23 14:12:21

by Adam Ford

[permalink] [raw]
Subject: [PATCH V3] ARM: dts: imx: Add support for Logic PD i.MX6QD EVM

The EVM consists of a system on module (SOM) and baseboard, and LCD.
This patch adds a DTSI file for the SOM and baseboard separately,
then a wrapper to combine them and specify processor type and a
LCD information.

Signed-off-by: Adam Ford <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
---
V3: Change tmp102->temperature-sensor
Change at24->eeprom
Both per Fabio
V2: Make node names more generic and label names more specific.
Don't make audio regulator always-on.
Remove I2C touch controller until the driver is available
Switch LVDS display to a compatible display that's available
Fix memory node.
Fix whitespace

diff --git a/arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi b/arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi
new file mode 100644
index 000000000000..55cdb702a355
--- /dev/null
+++ b/arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi
@@ -0,0 +1,555 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2019 Logic PD, Inc.
+
+/ {
+ keyboard {
+ compatible = "gpio-keys";
+
+ btn0 {
+ gpios = <&pcf8575 0 GPIO_ACTIVE_LOW>;
+ label = "btn0";
+ linux,code = <KEY_WAKEUP>;
+ debounce-interval = <10>;
+ wakeup-source;
+ };
+
+ btn1 {
+ gpios = <&pcf8575 1 GPIO_ACTIVE_LOW>;
+ label = "btn1";
+ linux,code = <KEY_WAKEUP>;
+ debounce-interval = <10>;
+ wakeup-source;
+ };
+
+ btn2 {
+ gpios = <&pcf8575 2 GPIO_ACTIVE_LOW>;
+ label = "btn2";
+ linux,code = <KEY_WAKEUP>;
+ debounce-interval = <10>;
+ wakeup-source;
+ };
+ btn3 {
+ gpios = <&pcf8575 3 GPIO_ACTIVE_LOW>;
+ label = "btn3";
+ linux,code = <KEY_WAKEUP>;
+ debounce-interval = <10>;
+ wakeup-source;
+ };
+
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ gen_led0 {
+ label = "led0";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_led0>;
+ gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "cpu0";
+ };
+
+ gen_led1 {
+ label = "led1";
+ gpios = <&pcf8575 8 GPIO_ACTIVE_HIGH>;
+ };
+
+ gen_led2 {
+ label = "led2";
+ gpios = <&pcf8575 9 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ gen_led3 {
+ label = "led3";
+ gpios = <&pcf8575 10 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+ };
+
+ reg_usb_otg_vbus: regulator-otg-vbus {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_usb_otg>;
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usb_h1_vbus: regulator-usb-h1-vbus {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_usb_h1_vbus>;
+ compatible = "regulator-fixed";
+ regulator-name = "usb_h1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_3v3: regulator-3v3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_3v3>;
+ compatible = "regulator-fixed";
+ regulator-name = "reg_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+
+ reg_enet: regulator-ethernet {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_enet>;
+ compatible = "regulator-fixed";
+ regulator-name = "ethernet-supply";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <70000>;
+ enable-active-high;
+ vin-supply = <&sw4_reg>;
+ };
+
+ reg_audio: regulator-audio {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_audio>;
+ compatible = "regulator-fixed";
+ regulator-name = "3v3_aud";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <&reg_3v3>;
+ };
+
+ reg_hdmi: regulator-hdmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_hdmi>;
+ compatible = "regulator-fixed";
+ regulator-name = "hdmi-supply";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ vin-supply = <&reg_3v3>;
+ };
+
+ reg_uart3: regulator-uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_uart3>;
+ compatible = "regulator-fixed";
+ regulator-name = "uart3-supply";
+ gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ vin-supply = <&reg_3v3>;
+ };
+
+ reg_1v8: regulator-1v8 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_1v8>;
+ compatible = "regulator-fixed";
+ regulator-name = "1v8-supply";
+ gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ vin-supply = <&reg_3v3>;
+ };
+
+ reg_pcie: regulator-pcie {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_pcie>;
+ regulator-name = "mpcie_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_mipi: regulator-mipi {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_mipi>;
+ regulator-name = "mipi_pwr_en";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ gpio = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ sound {
+ compatible = "fsl,imx-audio-wm8962";
+ model = "wm8962-audio";
+ ssi-controller = <&ssi2>;
+ audio-codec = <&wm8962>;
+ audio-routing =
+ "Headphone Jack", "HPOUTL",
+ "Headphone Jack", "HPOUTR",
+ "Ext Spk", "SPKOUTL",
+ "Ext Spk", "SPKOUTR",
+ "AMIC", "MICBIAS",
+ "IN3R", "AMIC";
+ mux-int-port = <2>;
+ mux-ext-port = <4>;
+ };
+};
+
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+};
+
+&ecspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "disabled";
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii";
+ phy-reset-duration = <10>;
+ phy-reset-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
+ phy-supply = <&reg_enet>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ clock-frequency = <400000>;
+ status = "okay";
+
+ wm8962: codec@1a {
+ compatible = "wlf,wm8962";
+ reg = <0x1a>;
+ clocks = <&clks IMX6QDL_CLK_CKO>;
+ clock-names = "xclk";
+ DCVDD-supply = <&reg_audio>;
+ DBVDD-supply = <&reg_audio>;
+ AVDD-supply = <&reg_audio>;
+ CPVDD-supply = <&reg_audio>;
+ MICVDD-supply = <&reg_audio>;
+ PLLVDD-supply = <&reg_audio>;
+ SPKVDD1-supply = <&reg_audio>;
+ SPKVDD2-supply = <&reg_audio>;
+ gpio-cfg = <
+ 0x0000 /* 0:Default */
+ 0x0000 /* 1:Default */
+ 0x0013 /* 2:FN_DMICCLK */
+ 0x0000 /* 3:Default */
+ 0x8014 /* 4:FN_DMICCDAT */
+ 0x0000 /* 5:Default */
+ >;
+ };
+};
+
+&i2c3 {
+ ov5640: camera@10 {
+ compatible = "ovti,ov5640";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ov5640>;
+ reg = <0x10>;
+ clocks = <&clks IMX6QDL_CLK_CKO>;
+ clock-names = "xclk";
+ DOVDD-supply = <&reg_mipi>;
+ AVDD-supply = <&reg_mipi>;
+ DVDD-supply = <&reg_mipi>;
+ reset-gpios = <&gpio3 26 GPIO_ACTIVE_LOW>;
+ powerdown-gpios = <&gpio3 27 GPIO_ACTIVE_HIGH>;
+
+ port {
+ ov5640_to_mipi_csi2: endpoint {
+ remote-endpoint = <&mipi_csi2_in>;
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+
+ pcf8575: gpio@20 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcf8574>;
+ compatible = "nxp,pcf8575";
+ reg = <0x20>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ lines-initial-states = <0x0710>;
+ wakeup-source;
+ };
+};
+
+&ipu1_csi1_from_mipi_vc1 {
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+};
+
+&mipi_csi {
+ status = "okay";
+
+ port@0 {
+ reg = <0>;
+
+ mipi_csi2_in: endpoint {
+ remote-endpoint = <&ov5640_to_mipi_csi2>;
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie>;
+ reset-gpio = <&gpio1 9 GPIO_ACTIVE_LOW>;
+ status = "okay";
+ vpcie-supply = <&reg_pcie>;
+};
+
+&pwm3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm3>;
+};
+
+&ssi2 {
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <&reg_usb_h1_vbus>;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <&reg_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+ vmmc-supply = <&reg_3v3>;
+ no-1-8-v;
+ keep-power-in-suspend;
+ status = "okay";
+ cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+};
+
+&iomuxc {
+
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT20__AUD4_TXC 0x130b0
+ MX6QDL_PAD_DISP0_DAT21__AUD4_TXD 0x110b0
+ MX6QDL_PAD_DISP0_DAT22__AUD4_TXFS 0x130b0
+ MX6QDL_PAD_DISP0_DAT23__AUD4_RXD 0x130b0
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__ECSPI1_SCLK 0x100b1
+ MX6QDL_PAD_KEY_ROW0__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_KEY_COL1__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_KEY_ROW1__ECSPI1_SS0 0x100b1
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b8b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x100b0
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b030
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x13030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x13030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x13030
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0 /* ENET_INT */
+ MX6QDL_PAD_ENET_RX_ER__GPIO1_IO24 0x1b0b0 /* ETHR_nRST */
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_led0: led0grp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x1b0b0
+ >;
+ };
+
+ pinctrl_ov5640: ov5640grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D26__GPIO3_IO26 0x1b0b1
+ MX6QDL_PAD_EIM_D27__GPIO3_IO27 0x1b0b1
+ >;
+ };
+
+ pinctrl_pcf8574: pcf8575grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0x1b0b0
+ >;
+ };
+
+ pinctrl_pcie: pciegrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
+ MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0
+ >;
+ };
+
+ pinctrl_pwm3: pwm3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D23__UART3_CTS_B 0x1b0b1
+ MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_EB3__UART3_RTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__USB_OTG_ID 0xd17059
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b0 /* CD */
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17069
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10069
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17069
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17069
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17069
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17069
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: h100-usdhc2-100mhz {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b0 /* CD */
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: h100-usdhc2-200mhz {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b0 /* CD */
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170f9
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100f9
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170f9
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170f9
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170f9
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170f9
+ >;
+ };
+
+ pinctrl_reg_1v8: reg1v8grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x1b0b0
+ >;
+ };
+
+ pinctrl_reg_3v3: reg3v3grp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b0b0
+ >;
+ };
+
+ pinctrl_reg_audio: reg-audiogrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x1b0b0
+ >;
+ };
+
+ pinctrl_reg_enet: reg-enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x1b0b0
+ >;
+ };
+
+ pinctrl_reg_hdmi: reg-hdmigrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b0
+ >;
+ };
+
+ pinctrl_reg_mipi: reg-mipigrp {
+ fsl,pins = <MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x1b0b1>;
+ };
+
+ pinctrl_reg_pcie: reg-pciegrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
+ >;
+ };
+
+ pinctrl_reg_uart3: reguart3grp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b0
+ >;
+ };
+
+ pinctrl_reg_usb_h1_vbus: usbh1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
+ >;
+ };
+
+ pinctrl_reg_usb_otg: reg-usb-otggrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x1b0b0
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6-logicpd-som.dtsi b/arch/arm/boot/dts/imx6-logicpd-som.dtsi
new file mode 100644
index 000000000000..078588798403
--- /dev/null
+++ b/arch/arm/boot/dts/imx6-logicpd-som.dtsi
@@ -0,0 +1,363 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2019 Logic PD, Inc.
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0x80000000>;
+ };
+
+ reg_wl18xx_vmmc: regulator-wl18xx {
+ compatible = "regulator-fixed";
+ regulator-name = "vwl1837";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio7 0 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <70000>;
+ enable-active-high;
+ };
+};
+
+&clks {
+ assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
+ <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
+ assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
+ <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ status = "okay";
+ nand-on-flash-bbt;
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ pfuze100: pmic@8 {
+ compatible = "fsl,pfuze100";
+ reg = <0x08>;
+
+ regulators {
+ sw1a_reg: sw1ab {
+ regulator-min-microvolt = <725000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-name = "vddcore";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw1c_reg: sw1c {
+ regulator-min-microvolt = <725000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-name = "vddsoc";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "gen_3v3";
+ regulator-boot-on;
+ };
+
+ sw3a_reg: sw3a {
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-name = "sw3a_vddr";
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3b_reg: sw3b {
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-name = "sw3b_vddr";
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw4_reg: sw4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "gen_rgmii";
+ };
+
+ swbst_reg: swbst {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5150000>;
+ regulator-name = "gen_5v0";
+ };
+
+ snvs_reg: vsnvs {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "gen_vsns";
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vref_reg: vrefddr {
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vgen1_reg: vgen1 {
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "gen_1v5";
+ };
+
+ vgen2_reg: vgen2 {
+ regulator-name = "vgen2";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vgen3_reg: vgen3 {
+ regulator-name = "gen_vadj_0";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vgen4_reg: vgen4 {
+ regulator-name = "gen_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ vgen5_reg: vgen5 {
+ regulator-name = "gen_vadj_1";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen6_reg: vgen6 {
+ regulator-name = "gen_2v5";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-always-on;
+ };
+
+ coin_reg: coin {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ };
+ };
+ };
+
+ temperature-sensor@4a {
+ compatible = "ti,tmp102";
+ reg = <0x4a>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tempsense>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+ #thermal-sensor-cells = <1>;
+ };
+
+ temperature-sensor@49 {
+ compatible = "ti,tmp102";
+ reg = <0x49>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+ #thermal-sensor-cells = <1>;
+ };
+
+ eeprom@51 {
+ compatible = "atmel,24c64";
+ pagesize = <32>;
+ read-only; /* Manufacturing EEPROM programmed at factory */
+ reg = <0x51>;
+ };
+
+ eeprom@52 {
+ compatible = "atmel,24c64";
+ pagesize = <32>;
+ reg = <0x52>;
+ };
+};
+
+/* Reroute power feeding the CPU to come from the external PMIC */
+&reg_arm
+{
+ vin-supply = <&sw1a_reg>;
+};
+
+&reg_soc
+{
+ vin-supply = <&sw1c_reg>;
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ pinctrl_hog: hoggrp {
+ fsl,pins = < /* Enable ARM Debugger */
+ MX6QDL_PAD_CSI0_MCLK__ARM_TRACE_CTL 0x1b0b0
+ MX6QDL_PAD_CSI0_PIXCLK__ARM_EVENTO 0x1b0b0
+ MX6QDL_PAD_CSI0_VSYNC__ARM_TRACE00 0x1b0b0
+ MX6QDL_PAD_CSI0_DATA_EN__ARM_TRACE_CLK 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT4__ARM_TRACE01 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT5__ARM_TRACE02 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT6__ARM_TRACE03 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT7__ARM_TRACE04 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT8__ARM_TRACE05 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT9__ARM_TRACE06 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT10__ARM_TRACE07 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT11__ARM_TRACE08 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT12__ARM_TRACE09 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT13__ARM_TRACE10 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT14__ARM_TRACE11 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT15__ARM_TRACE12 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT16__ARM_TRACE13 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT17__ARM_TRACE14 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT18__ARM_TRACE15 0x1b0b0
+ MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0
+ >;
+ };
+
+ pinctrl_gpmi_nand: gpmi-nandgrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CLE__NAND_CLE 0x0b0b1
+ MX6QDL_PAD_NANDF_ALE__NAND_ALE 0x0b0b1
+ MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0x0b0b1
+ MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0x0b000
+ MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0x0b0b1
+ MX6QDL_PAD_SD4_CMD__NAND_RE_B 0x0b0b1
+ MX6QDL_PAD_SD4_CLK__NAND_WE_B 0x0b0b1
+ MX6QDL_PAD_NANDF_D0__NAND_DATA00 0x0b0b1
+ MX6QDL_PAD_NANDF_D1__NAND_DATA01 0x0b0b1
+ MX6QDL_PAD_NANDF_D2__NAND_DATA02 0x0b0b1
+ MX6QDL_PAD_NANDF_D3__NAND_DATA03 0x0b0b1
+ MX6QDL_PAD_NANDF_D4__NAND_DATA04 0x0b0b1
+ MX6QDL_PAD_NANDF_D5__NAND_DATA05 0x0b0b1
+ MX6QDL_PAD_NANDF_D6__NAND_DATA06 0x0b0b1
+ MX6QDL_PAD_NANDF_D7__NAND_DATA07 0x0b0b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1
+ MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x13059 /* BT_EN */
+ MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1
+ MX6QDL_PAD_SD4_DAT5__UART2_RTS_B 0x1b0b1
+ MX6QDL_PAD_SD4_DAT6__UART2_CTS_B 0x1b0b1
+ MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170B9
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100B9
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170B9
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170B9
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170B9
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170B9
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17049
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10049
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17049
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17049
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17049
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17049
+ MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x130b0 /* WL_IRQ */
+ MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x17059 /* WLAN_EN */
+ >;
+ };
+
+ pinctrl_tempsense: tempsensegrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x1b0b0
+ >;
+ };
+};
+
+&snvs_poweroff {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+ uart-has-rtscts;
+ bluetooth {
+ compatible = "ti,wl1837-st";
+ enable-gpios = <&gpio7 8 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&usdhc1 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ non-removable;
+ keep-power-in-suspend;
+ enable-sdio-wakeup;
+ status = "okay";
+ vmmc-supply = <&sw2_reg>;
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ non-removable;
+ cap-power-off-card;
+ keep-power-in-suspend;
+ wakeup-source;
+ vmmc-supply = <&reg_wl18xx_vmmc>;
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ wlcore: wlcore@2 {
+ compatible = "ti,wl1837";
+ reg = <2>;
+ interrupt-parent = <&gpio7>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
+ tcxo-clock-frequency = <26000000>;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6q-logicpd.dts b/arch/arm/boot/dts/imx6q-logicpd.dts
new file mode 100644
index 000000000000..877a4599e564
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-logicpd.dts
@@ -0,0 +1,120 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2019 Logic PD, Inc.
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6-logicpd-som.dtsi"
+#include "imx6-logicpd-baseboard.dtsi"
+
+/ {
+ model = "Logic PD i.MX6QD SOM-M3";
+ compatible = "fsl,imx6q";
+
+ backlight: backlight_lvds {
+ compatible = "pwm-backlight";
+ pwms = <&pwm3 0 20000>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <6>;
+ power-supply = <&reg_lcd>;
+ };
+
+ panel-lvds0 {
+ compatible = "okaya,rs800480t-7x0gp";
+
+ port {
+ panel_in_lvds0: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+
+ reg_lcd: regulator-lcd {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd_reg>;
+ compatible = "regulator-fixed";
+ regulator-name = "lcd_panel_pwr";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio4 17 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ vin-supply = <&reg_3v3>;
+ startup-delay-us = <500000>;
+ };
+
+ reg_lcd_reset: regulator-lcd-reset {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd_reset>;
+ compatible = "regulator-fixed";
+ regulator-name = "nLCD_RESET";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ vin-supply = <&reg_lcd>;
+ };
+};
+
+&clks {
+ assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
+ <&clks IMX6QDL_CLK_LDB_DI1_SEL>,
+ <&clks IMX6QDL_CLK_IPU1_DI0_PRE_SEL>,
+ <&clks IMX6QDL_CLK_IPU2_DI0_PRE_SEL>;
+ assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>,
+ <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>,
+ <&clks IMX6QDL_CLK_PLL2_PFD2_396M>,
+ <&clks IMX6QDL_CLK_PLL2_PFD2_396M>;
+};
+
+&hdmi {
+ ddc-i2c-bus = <&i2c3>;
+ status = "okay";
+};
+
+&ldb {
+ status = "okay";
+
+ lvds-channel@0 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <24>;
+ status = "okay";
+
+ port@4 {
+ reg = <4>;
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in_lvds0>;
+ };
+ };
+ };
+
+};
+
+&pwm3 {
+ status = "okay";
+};
+
+&reg_hdmi {
+ regulator-always-on; /* Without this, the level shifter on HDMI doesn't turn on */
+};
+
+&iomuxc {
+ pinctrl_lcd_reg: lcdreg {
+ fsl,pins = <
+ MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x100b0 /* R_LCD_PANEL_PWR */
+ >;
+ };
+
+ pinctrl_lcd_reset: lcdreset {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x100b0 /* LCD_nRESET */
+ >;
+ };
+
+ pinctrl_touchscreen: touchscreengrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x1b0b0 /* TOUCH_nPINTDAV */
+ >;
+ };
+};
--
2.17.1



2019-02-01 06:52:28

by Shawn Guo

[permalink] [raw]
Subject: Re: [PATCH V3] ARM: dts: imx: Add support for Logic PD i.MX6QD EVM

On Wed, Jan 23, 2019 at 08:10:17AM -0600, Adam Ford wrote:
> The EVM consists of a system on module (SOM) and baseboard, and LCD.
> This patch adds a DTSI file for the SOM and baseboard separately,
> then a wrapper to combine them and specify processor type and a
> LCD information.
>
> Signed-off-by: Adam Ford <[email protected]>
> Reviewed-by: Fabio Estevam <[email protected]>
> ---
> V3: Change tmp102->temperature-sensor
> Change at24->eeprom
> Both per Fabio
> V2: Make node names more generic and label names more specific.
> Don't make audio regulator always-on.
> Remove I2C touch controller until the driver is available
> Switch LVDS display to a compatible display that's available
> Fix memory node.
> Fix whitespace
>
> diff --git a/arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi b/arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi
> new file mode 100644
> index 000000000000..55cdb702a355
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi
> @@ -0,0 +1,555 @@
> +// SPDX-License-Identifier: GPL-2.0
> +//
> +// Copyright (C) 2019 Logic PD, Inc.
> +
> +/ {
> + keyboard {
> + compatible = "gpio-keys";
> +
> + btn0 {
> + gpios = <&pcf8575 0 GPIO_ACTIVE_LOW>;
> + label = "btn0";
> + linux,code = <KEY_WAKEUP>;
> + debounce-interval = <10>;
> + wakeup-source;
> + };
> +
> + btn1 {
> + gpios = <&pcf8575 1 GPIO_ACTIVE_LOW>;
> + label = "btn1";
> + linux,code = <KEY_WAKEUP>;
> + debounce-interval = <10>;
> + wakeup-source;
> + };
> +
> + btn2 {
> + gpios = <&pcf8575 2 GPIO_ACTIVE_LOW>;
> + label = "btn2";
> + linux,code = <KEY_WAKEUP>;
> + debounce-interval = <10>;
> + wakeup-source;
> + };

Have a newline between nodes.

> + btn3 {
> + gpios = <&pcf8575 3 GPIO_ACTIVE_LOW>;
> + label = "btn3";
> + linux,code = <KEY_WAKEUP>;
> + debounce-interval = <10>;
> + wakeup-source;
> + };
> +
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + gen_led0 {

We prefer to use hyphen than underscore in node name.

> + label = "led0";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_led0>;
> + gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "cpu0";
> + };
> +
> + gen_led1 {
> + label = "led1";
> + gpios = <&pcf8575 8 GPIO_ACTIVE_HIGH>;
> + };
> +
> + gen_led2 {
> + label = "led2";
> + gpios = <&pcf8575 9 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> +
> + gen_led3 {
> + label = "led3";
> + gpios = <&pcf8575 10 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "default-on";
> + };
> + };
> +
> + reg_usb_otg_vbus: regulator-otg-vbus {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_usb_otg>;
> + compatible = "regulator-fixed";
> + regulator-name = "usb_otg_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + reg_usb_h1_vbus: regulator-usb-h1-vbus {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_usb_h1_vbus>;
> + compatible = "regulator-fixed";
> + regulator-name = "usb_h1_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + reg_3v3: regulator-3v3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_3v3>;
> + compatible = "regulator-fixed";
> + regulator-name = "reg_3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-always-on;
> + };
> +
> +

One newline is good enough.

> + reg_enet: regulator-ethernet {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_enet>;
> + compatible = "regulator-fixed";
> + regulator-name = "ethernet-supply";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
> + startup-delay-us = <70000>;
> + enable-active-high;
> + vin-supply = <&sw4_reg>;
> + };
> +
> + reg_audio: regulator-audio {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_audio>;
> + compatible = "regulator-fixed";
> + regulator-name = "3v3_aud";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio1 29 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + vin-supply = <&reg_3v3>;
> + };
> +
> + reg_hdmi: regulator-hdmi {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_hdmi>;
> + compatible = "regulator-fixed";
> + regulator-name = "hdmi-supply";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + vin-supply = <&reg_3v3>;
> + };
> +
> + reg_uart3: regulator-uart3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_uart3>;
> + compatible = "regulator-fixed";
> + regulator-name = "uart3-supply";
> + gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-always-on;
> + vin-supply = <&reg_3v3>;
> + };
> +
> + reg_1v8: regulator-1v8 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_1v8>;
> + compatible = "regulator-fixed";
> + regulator-name = "1v8-supply";
> + gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-always-on;
> + vin-supply = <&reg_3v3>;
> + };
> +
> + reg_pcie: regulator-pcie {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_pcie>;
> + regulator-name = "mpcie_3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + reg_mipi: regulator-mipi {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_mipi>;
> + regulator-name = "mipi_pwr_en";
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + gpio = <&gpio3 19 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + sound {
> + compatible = "fsl,imx-audio-wm8962";
> + model = "wm8962-audio";
> + ssi-controller = <&ssi2>;
> + audio-codec = <&wm8962>;
> + audio-routing =
> + "Headphone Jack", "HPOUTL",
> + "Headphone Jack", "HPOUTR",
> + "Ext Spk", "SPKOUTL",
> + "Ext Spk", "SPKOUTR",
> + "AMIC", "MICBIAS",
> + "IN3R", "AMIC";
> + mux-int-port = <2>;
> + mux-ext-port = <4>;
> + };
> +};
> +
> +&audmux {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_audmux>;
> + status = "okay";
> +};
> +
> +&ecspi1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi1>;
> + status = "disabled";
> +};
> +
> +&fec {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_enet>;
> + phy-mode = "rgmii";
> + phy-reset-duration = <10>;
> + phy-reset-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
> + phy-supply = <&reg_enet>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> + status = "okay";
> +};
> +
> +&i2c1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + clock-frequency = <400000>;
> + status = "okay";
> +
> + wm8962: codec@1a {

audio-codec for node name.

> + compatible = "wlf,wm8962";
> + reg = <0x1a>;
> + clocks = <&clks IMX6QDL_CLK_CKO>;
> + clock-names = "xclk";
> + DCVDD-supply = <&reg_audio>;
> + DBVDD-supply = <&reg_audio>;
> + AVDD-supply = <&reg_audio>;
> + CPVDD-supply = <&reg_audio>;
> + MICVDD-supply = <&reg_audio>;
> + PLLVDD-supply = <&reg_audio>;
> + SPKVDD1-supply = <&reg_audio>;
> + SPKVDD2-supply = <&reg_audio>;
> + gpio-cfg = <
> + 0x0000 /* 0:Default */
> + 0x0000 /* 1:Default */
> + 0x0013 /* 2:FN_DMICCLK */
> + 0x0000 /* 3:Default */
> + 0x8014 /* 4:FN_DMICCDAT */
> + 0x0000 /* 5:Default */
> + >;
> + };
> +};
> +
> +&i2c3 {
> + ov5640: camera@10 {
> + compatible = "ovti,ov5640";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ov5640>;
> + reg = <0x10>;
> + clocks = <&clks IMX6QDL_CLK_CKO>;
> + clock-names = "xclk";
> + DOVDD-supply = <&reg_mipi>;
> + AVDD-supply = <&reg_mipi>;
> + DVDD-supply = <&reg_mipi>;
> + reset-gpios = <&gpio3 26 GPIO_ACTIVE_LOW>;
> + powerdown-gpios = <&gpio3 27 GPIO_ACTIVE_HIGH>;
> +
> + port {
> + ov5640_to_mipi_csi2: endpoint {
> + remote-endpoint = <&mipi_csi2_in>;
> + clock-lanes = <0>;
> + data-lanes = <1 2>;
> + };
> + };
> + };
> +
> + pcf8575: gpio@20 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pcf8574>;
> + compatible = "nxp,pcf8575";
> + reg = <0x20>;
> + interrupt-parent = <&gpio6>;
> + interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + lines-initial-states = <0x0710>;
> + wakeup-source;
> + };
> +};
> +
> +&ipu1_csi1_from_mipi_vc1 {
> + clock-lanes = <0>;
> + data-lanes = <1 2>;
> +};
> +
> +&mipi_csi {
> + status = "okay";
> +
> + port@0 {
> + reg = <0>;
> +
> + mipi_csi2_in: endpoint {
> + remote-endpoint = <&ov5640_to_mipi_csi2>;
> + clock-lanes = <0>;
> + data-lanes = <1 2>;
> + };
> + };
> +};
> +
> +&pcie {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pcie>;
> + reset-gpio = <&gpio1 9 GPIO_ACTIVE_LOW>;
> + status = "okay";

Please end property list with 'status'.

> + vpcie-supply = <&reg_pcie>;
> +};
> +
> +&pwm3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm3>;
> +};
> +
> +&ssi2 {
> + status = "okay";
> +};
> +
> +&uart3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart3>;
> + status = "okay";
> +};
> +
> +&usbh1 {
> + vbus-supply = <&reg_usb_h1_vbus>;
> + status = "okay";
> +};
> +
> +&usbotg {
> + vbus-supply = <&reg_usb_otg_vbus>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbotg>;
> + disable-over-current;
> + dr_mode = "otg";
> + status = "okay";
> +};
> +
> +&usdhc2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc2>;
> + pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
> + vmmc-supply = <&reg_3v3>;
> + no-1-8-v;
> + keep-power-in-suspend;
> + status = "okay";

Ditto

> + cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
> +};
> +
> +&iomuxc {
> +

Drop this newline.

> + pinctrl_audmux: audmuxgrp {
> + fsl,pins = <
> + MX6QDL_PAD_DISP0_DAT20__AUD4_TXC 0x130b0
> + MX6QDL_PAD_DISP0_DAT21__AUD4_TXD 0x110b0
> + MX6QDL_PAD_DISP0_DAT22__AUD4_TXFS 0x130b0
> + MX6QDL_PAD_DISP0_DAT23__AUD4_RXD 0x130b0
> + >;
> + };
> +
> + pinctrl_ecspi1: ecspi1grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL0__ECSPI1_SCLK 0x100b1
> + MX6QDL_PAD_KEY_ROW0__ECSPI1_MOSI 0x100b1
> + MX6QDL_PAD_KEY_COL1__ECSPI1_MISO 0x100b1
> + MX6QDL_PAD_KEY_ROW1__ECSPI1_SS0 0x100b1
> + >;
> + };
> +
> + pinctrl_enet: enetgrp {
> + fsl,pins = <
> + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b8b0
> + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
> + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b030
> + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b030
> + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b030
> + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b030
> + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b030
> + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x100b0
> + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b030
> + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
> + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
> + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x13030
> + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x13030
> + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
> + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
> + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x13030
> + MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0 /* ENET_INT */
> + MX6QDL_PAD_ENET_RX_ER__GPIO1_IO24 0x1b0b0 /* ETHR_nRST */
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
> + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
> + >;
> + };
> +
> + pinctrl_led0: led0grp {
> + fsl,pins = <
> + MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x1b0b0
> + >;
> + };
> +
> + pinctrl_ov5640: ov5640grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D26__GPIO3_IO26 0x1b0b1
> + MX6QDL_PAD_EIM_D27__GPIO3_IO27 0x1b0b1
> + >;
> + };
> +
> + pinctrl_pcf8574: pcf8575grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0x1b0b0
> + >;
> + };
> +
> + pinctrl_pcie: pciegrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
> + MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0
> + >;
> + };
> +
> + pinctrl_pwm3: pwm3grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1
> + >;
> + };
> +
> + pinctrl_uart3: uart3grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D23__UART3_CTS_B 0x1b0b1
> + MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
> + MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
> + MX6QDL_PAD_EIM_EB3__UART3_RTS_B 0x1b0b1
> + >;
> + };
> +
> + pinctrl_usbotg: usbotggrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0xd17059
> + >;
> + };
> +
> + pinctrl_usdhc2: usdhc2grp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b0 /* CD */
> + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17069
> + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10069
> + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17069
> + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17069
> + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17069
> + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17069
> + >;
> + };
> +
> + pinctrl_usdhc2_100mhz: h100-usdhc2-100mhz {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b0 /* CD */
> + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
> + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
> + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
> + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
> + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
> + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
> + >;
> + };
> +
> + pinctrl_usdhc2_200mhz: h100-usdhc2-200mhz {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b0 /* CD */
> + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170f9
> + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100f9
> + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170f9
> + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170f9
> + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170f9
> + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170f9
> + >;
> + };
> +
> + pinctrl_reg_1v8: reg1v8grp {

Please sort these pinctrl nodes alphabetically.

> + fsl,pins = <
> + MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x1b0b0
> + >;
> + };
> +
> + pinctrl_reg_3v3: reg3v3grp {
> + fsl,pins = <
> + MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b0b0
> + >;
> + };
> +
> + pinctrl_reg_audio: reg-audiogrp {
> + fsl,pins = <
> + MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x1b0b0
> + >;
> + };
> +
> + pinctrl_reg_enet: reg-enetgrp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x1b0b0
> + >;
> + };
> +
> + pinctrl_reg_hdmi: reg-hdmigrp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b0
> + >;
> + };
> +
> + pinctrl_reg_mipi: reg-mipigrp {
> + fsl,pins = <MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x1b0b1>;
> + };
> +
> + pinctrl_reg_pcie: reg-pciegrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
> + >;
> + };
> +
> + pinctrl_reg_uart3: reguart3grp {
> + fsl,pins = <
> + MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b0
> + >;
> + };
> +
> + pinctrl_reg_usb_h1_vbus: usbh1grp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
> + >;
> + };
> +
> + pinctrl_reg_usb_otg: reg-usb-otggrp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x1b0b0
> + >;
> + };
> +};
> diff --git a/arch/arm/boot/dts/imx6-logicpd-som.dtsi b/arch/arm/boot/dts/imx6-logicpd-som.dtsi
> new file mode 100644
> index 000000000000..078588798403
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6-logicpd-som.dtsi
> @@ -0,0 +1,363 @@
> +// SPDX-License-Identifier: GPL-2.0
> +//
> +// Copyright (C) 2019 Logic PD, Inc.
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> + chosen {
> + stdout-path = &uart1;
> + };
> +
> + memory@10000000 {
> + device_type = "memory";
> + reg = <0x10000000 0x80000000>;
> + };
> +
> + reg_wl18xx_vmmc: regulator-wl18xx {
> + compatible = "regulator-fixed";
> + regulator-name = "vwl1837";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio7 0 GPIO_ACTIVE_HIGH>;
> + startup-delay-us = <70000>;
> + enable-active-high;
> + };
> +};
> +
> +&clks {
> + assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
> + <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
> + assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
> + <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
> +};
> +
> +&gpmi {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpmi_nand>;
> + status = "okay";

Move it to end of property list.

> + nand-on-flash-bbt;
> +};
> +
> +&i2c3 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c3>;
> + status = "okay";
> +
> + pfuze100: pmic@8 {
> + compatible = "fsl,pfuze100";
> + reg = <0x08>;
> +
> + regulators {
> + sw1a_reg: sw1ab {
> + regulator-min-microvolt = <725000>;
> + regulator-max-microvolt = <1450000>;
> + regulator-name = "vddcore";
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <6250>;
> + };
> +
> + sw1c_reg: sw1c {
> + regulator-min-microvolt = <725000>;
> + regulator-max-microvolt = <1450000>;
> + regulator-name = "vddsoc";
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <6250>;
> + };
> +
> + sw2_reg: sw2 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "gen_3v3";
> + regulator-boot-on;
> + };
> +
> + sw3a_reg: sw3a {
> + regulator-min-microvolt = <1350000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-name = "sw3a_vddr";
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + sw3b_reg: sw3b {
> + regulator-min-microvolt = <1350000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-name = "sw3b_vddr";
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + sw4_reg: sw4 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "gen_rgmii";
> + };
> +
> + swbst_reg: swbst {
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5150000>;
> + regulator-name = "gen_5v0";
> + };
> +
> + snvs_reg: vsnvs {
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-name = "gen_vsns";
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vref_reg: vrefddr {
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vgen1_reg: vgen1 {
> + regulator-min-microvolt = <1500000>;
> + regulator-max-microvolt = <1500000>;
> + regulator-name = "gen_1v5";
> + };
> +
> + vgen2_reg: vgen2 {
> + regulator-name = "vgen2";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1550000>;
> + };
> +
> + vgen3_reg: vgen3 {
> + regulator-name = "gen_vadj_0";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + vgen4_reg: vgen4 {
> + regulator-name = "gen_1v8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + vgen5_reg: vgen5 {
> + regulator-name = "gen_vadj_1";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + vgen6_reg: vgen6 {
> + regulator-name = "gen_2v5";
> + regulator-min-microvolt = <2500000>;
> + regulator-max-microvolt = <2500000>;
> + regulator-always-on;
> + };
> +
> + coin_reg: coin {
> + regulator-min-microvolt = <2500000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-always-on;
> + };
> + };
> + };
> +
> + temperature-sensor@4a {
> + compatible = "ti,tmp102";
> + reg = <0x4a>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_tempsense>;
> + interrupt-parent = <&gpio6>;
> + interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
> + #thermal-sensor-cells = <1>;
> + };
> +
> + temperature-sensor@49 {

Please keep nodes with unit-address sorted in the address order.

> + compatible = "ti,tmp102";
> + reg = <0x49>;
> + interrupt-parent = <&gpio6>;
> + interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
> + #thermal-sensor-cells = <1>;
> + };
> +
> + eeprom@51 {
> + compatible = "atmel,24c64";
> + pagesize = <32>;
> + read-only; /* Manufacturing EEPROM programmed at factory */
> + reg = <0x51>;
> + };
> +
> + eeprom@52 {
> + compatible = "atmel,24c64";
> + pagesize = <32>;
> + reg = <0x52>;
> + };
> +};
> +
> +/* Reroute power feeding the CPU to come from the external PMIC */
> +&reg_arm
> +{
> + vin-supply = <&sw1a_reg>;
> +};
> +
> +&reg_soc
> +{
> + vin-supply = <&sw1c_reg>;
> +};
> +
> +&iomuxc {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hog>;
> +
> + pinctrl_hog: hoggrp {
> + fsl,pins = < /* Enable ARM Debugger */
> + MX6QDL_PAD_CSI0_MCLK__ARM_TRACE_CTL 0x1b0b0
> + MX6QDL_PAD_CSI0_PIXCLK__ARM_EVENTO 0x1b0b0
> + MX6QDL_PAD_CSI0_VSYNC__ARM_TRACE00 0x1b0b0
> + MX6QDL_PAD_CSI0_DATA_EN__ARM_TRACE_CLK 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT4__ARM_TRACE01 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT5__ARM_TRACE02 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT6__ARM_TRACE03 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT7__ARM_TRACE04 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT8__ARM_TRACE05 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT9__ARM_TRACE06 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT10__ARM_TRACE07 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT11__ARM_TRACE08 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT12__ARM_TRACE09 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT13__ARM_TRACE10 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT14__ARM_TRACE11 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT15__ARM_TRACE12 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT16__ARM_TRACE13 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT17__ARM_TRACE14 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT18__ARM_TRACE15 0x1b0b0
> + MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0
> + >;
> + };
> +
> + pinctrl_gpmi_nand: gpmi-nandgrp {
> + fsl,pins = <
> + MX6QDL_PAD_NANDF_CLE__NAND_CLE 0x0b0b1
> + MX6QDL_PAD_NANDF_ALE__NAND_ALE 0x0b0b1
> + MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0x0b0b1
> + MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0x0b000
> + MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0x0b0b1
> + MX6QDL_PAD_SD4_CMD__NAND_RE_B 0x0b0b1
> + MX6QDL_PAD_SD4_CLK__NAND_WE_B 0x0b0b1
> + MX6QDL_PAD_NANDF_D0__NAND_DATA00 0x0b0b1
> + MX6QDL_PAD_NANDF_D1__NAND_DATA01 0x0b0b1
> + MX6QDL_PAD_NANDF_D2__NAND_DATA02 0x0b0b1
> + MX6QDL_PAD_NANDF_D3__NAND_DATA03 0x0b0b1
> + MX6QDL_PAD_NANDF_D4__NAND_DATA04 0x0b0b1
> + MX6QDL_PAD_NANDF_D5__NAND_DATA05 0x0b0b1
> + MX6QDL_PAD_NANDF_D6__NAND_DATA06 0x0b0b1
> + MX6QDL_PAD_NANDF_D7__NAND_DATA07 0x0b0b1
> + >;
> + };
> +
> + pinctrl_i2c3: i2c3grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1
> + MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
> + >;
> + };
> +
> + pinctrl_uart1: uart1grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1
> + MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1
> + >;
> + };
> +
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x13059 /* BT_EN */
> + MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1
> + MX6QDL_PAD_SD4_DAT5__UART2_RTS_B 0x1b0b1
> + MX6QDL_PAD_SD4_DAT6__UART2_CTS_B 0x1b0b1
> + MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1
> + >;
> + };
> +
> + pinctrl_usdhc1: usdhc1grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170B9
> + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100B9
> + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170B9
> + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170B9
> + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170B9
> + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170B9
> + >;
> + };
> +
> + pinctrl_usdhc3: usdhc3grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17049
> + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10049
> + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17049
> + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17049
> + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17049
> + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17049
> + MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x130b0 /* WL_IRQ */
> + MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x17059 /* WLAN_EN */
> + >;
> + };
> +
> + pinctrl_tempsense: tempsensegrp {

Sort it properly.

> + fsl,pins = <
> + MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x1b0b0
> + >;
> + };
> +};
> +
> +&snvs_poweroff {
> + status = "okay";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1>;
> + status = "okay";
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + status = "okay";

Move it to end.

> + uart-has-rtscts;

Have a newline between properties and child node.

> + bluetooth {
> + compatible = "ti,wl1837-st";
> + enable-gpios = <&gpio7 8 GPIO_ACTIVE_HIGH>;
> + };
> +};
> +
> +&usdhc1 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc1>;
> + non-removable;
> + keep-power-in-suspend;
> + enable-sdio-wakeup;

wakeup-source

> + status = "okay";

Move it to end.

> + vmmc-supply = <&sw2_reg>;
> +};
> +
> +&usdhc3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc3>;
> + non-removable;
> + cap-power-off-card;
> + keep-power-in-suspend;
> + wakeup-source;
> + vmmc-supply = <&reg_wl18xx_vmmc>;
> + status = "okay";

Move it to end.

> + #address-cells = <1>;
> + #size-cells = <0>;

Have a newline here.

> + wlcore: wlcore@2 {
> + compatible = "ti,wl1837";
> + reg = <2>;
> + interrupt-parent = <&gpio7>;
> + interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
> + tcxo-clock-frequency = <26000000>;
> + };
> +};
> diff --git a/arch/arm/boot/dts/imx6q-logicpd.dts b/arch/arm/boot/dts/imx6q-logicpd.dts
> new file mode 100644
> index 000000000000..877a4599e564
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-logicpd.dts
> @@ -0,0 +1,120 @@
> +// SPDX-License-Identifier: GPL-2.0
> +//
> +// Copyright (C) 2019 Logic PD, Inc.
> +
> +/dts-v1/;
> +#include "imx6q.dtsi"
> +#include "imx6-logicpd-som.dtsi"
> +#include "imx6-logicpd-baseboard.dtsi"
> +
> +/ {
> + model = "Logic PD i.MX6QD SOM-M3";
> + compatible = "fsl,imx6q";
> +
> + backlight: backlight_lvds {

Use hyphen.

Shawn

> + compatible = "pwm-backlight";
> + pwms = <&pwm3 0 20000>;
> + brightness-levels = <0 4 8 16 32 64 128 255>;
> + default-brightness-level = <6>;
> + power-supply = <&reg_lcd>;
> + };
> +
> + panel-lvds0 {
> + compatible = "okaya,rs800480t-7x0gp";
> +
> + port {
> + panel_in_lvds0: endpoint {
> + remote-endpoint = <&lvds0_out>;
> + };
> + };
> + };
> +
> + reg_lcd: regulator-lcd {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lcd_reg>;
> + compatible = "regulator-fixed";
> + regulator-name = "lcd_panel_pwr";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio4 17 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-always-on;
> + vin-supply = <&reg_3v3>;
> + startup-delay-us = <500000>;
> + };
> +
> + reg_lcd_reset: regulator-lcd-reset {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lcd_reset>;
> + compatible = "regulator-fixed";
> + regulator-name = "nLCD_RESET";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-always-on;
> + vin-supply = <&reg_lcd>;
> + };
> +};
> +
> +&clks {
> + assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
> + <&clks IMX6QDL_CLK_LDB_DI1_SEL>,
> + <&clks IMX6QDL_CLK_IPU1_DI0_PRE_SEL>,
> + <&clks IMX6QDL_CLK_IPU2_DI0_PRE_SEL>;
> + assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>,
> + <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>,
> + <&clks IMX6QDL_CLK_PLL2_PFD2_396M>,
> + <&clks IMX6QDL_CLK_PLL2_PFD2_396M>;
> +};
> +
> +&hdmi {
> + ddc-i2c-bus = <&i2c3>;
> + status = "okay";
> +};
> +
> +&ldb {
> + status = "okay";
> +
> + lvds-channel@0 {
> + fsl,data-mapping = "spwg";
> + fsl,data-width = <24>;
> + status = "okay";
> +
> + port@4 {
> + reg = <4>;
> + lvds0_out: endpoint {
> + remote-endpoint = <&panel_in_lvds0>;
> + };
> + };
> + };
> +
> +};
> +
> +&pwm3 {
> + status = "okay";
> +};
> +
> +&reg_hdmi {
> + regulator-always-on; /* Without this, the level shifter on HDMI doesn't turn on */
> +};
> +
> +&iomuxc {
> + pinctrl_lcd_reg: lcdreg {
> + fsl,pins = <
> + MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x100b0 /* R_LCD_PANEL_PWR */
> + >;
> + };
> +
> + pinctrl_lcd_reset: lcdreset {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x100b0 /* LCD_nRESET */
> + >;
> + };
> +
> + pinctrl_touchscreen: touchscreengrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x1b0b0 /* TOUCH_nPINTDAV */
> + >;
> + };
> +};
> --
> 2.17.1
>