From: Jonathan Bakker <[email protected]>
This commit adds documentation for Samsung s6e63m0 AMOLED LCD panel
driver.
Signed-off-by: Jonathan Bakker <[email protected]>
Signed-off-by: Paweł Chmiel <[email protected]>
---
Changes from v1:
- Add missing subject prefix
- Rename reset-gpio to reset-gpios
- Add link to spi properites documentation. They're required
for driver to work
- Removed delay properties, which are now hardcoded in driver
- Removed display timings, which are now hardcoded in driver
---
.../display/panel/samsung,s6e63m0.txt | 33 +++++++++++++++++++
1 file changed, 33 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/panel/samsung,s6e63m0.txt
diff --git a/Documentation/devicetree/bindings/display/panel/samsung,s6e63m0.txt b/Documentation/devicetree/bindings/display/panel/samsung,s6e63m0.txt
new file mode 100644
index 000000000000..9fb9ebeef8e4
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/samsung,s6e63m0.txt
@@ -0,0 +1,33 @@
+Samsung s6e63m0 AMOLED LCD panel
+
+Required properties:
+ - compatible: "samsung,s6e63m0"
+ - reset-gpios: GPIO spec for reset pin
+ - vdd3-supply: VDD regulator
+ - vci-supply: VCI regulator
+
+The panel must obey rules for SPI slave device specified in document [1].
+
+The device node can contain one 'port' child node with one child
+'endpoint' node, according to the bindings defined in [2]. This
+node should describe panel's video bus.
+
+[1]: Documentation/devicetree/bindings/spi/spi-bus.txt
+[2]: Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+
+ s6e63m0: display@0 {
+ compatible = "samsung,s6e63m0";
+ reg = <0>;
+ reset-gpio = <&mp05 5 1>;
+ vdd3-supply = <&ldo12_reg>;
+ vci-supply = <&ldo11_reg>;
+ spi-max-frequency = <1200000>;
+
+ port {
+ lcd_ep: endpoint {
+ remote-endpoint = <&fimd_ep>;
+ };
+ };
+ };
--
2.17.1
This patch adds Samsung S6E63M0 AMOLED LCD panel driver, connected over
spi. It's based on already removed, non dt s6e63m0 driver and
panel-samsung-ld9040. It can be found for example in some of Samsung
Aries based phones.
Signed-off-by: Paweł Chmiel <[email protected]>
---
Changes from v1:
- Correct order of Kconfig/Makefile entry
- Fix SPDX tag, so it matches value of MODULE_LICENSE
- Remove inclusion of drmP.h
- Fix code formatting
- Use DRM_DEV_ERROR/DEBUG
- Extract hardcoded values
- Remove possibility to change gamma through sysfs, leaving only one
gamma table values
- Fix reset_gpio handling, so it'll be asserted in power_on and
deasserted in power_off. Also do it before turning voltage on.
- Disable backlight and enter sleep mode in disable callback.
Previously it was done in unprepare
- Enable display and backlight in enable callback. Previously it was
done in prepare
- Hardcode display timings and delays. Previously they were readed
from device tree
- We're using SPDX, so we don't need to have license body
- Use MIPI_DCS_EXIT_SLEEP_MODE and MIPI_DCS_SET_DISPLAY_ON
- Rename MAX_GAMMA_LEVEL to NUM_GAMMA_LEVELS
- Ommit get_brightness callback
- Use backlight_enable/disable API, like it's done in other panel
drivers (for example panel-simple)
- Make set_brightness called only from backlight api, like it's done
in other panel drivers (for example panel-simple).
- Reset gpio should be set to GPIOD_OUT_HIGH. It's declared as active
low in device tree
- Don't call power_off in remove callback
---
drivers/gpu/drm/panel/Kconfig | 7 +
drivers/gpu/drm/panel/Makefile | 1 +
drivers/gpu/drm/panel/panel-samsung-s6e63m0.c | 517 ++++++++++++++++++
3 files changed, 525 insertions(+)
create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6e63m0.c
diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
index 3f3537719beb..be05ed5218eb 100644
--- a/drivers/gpu/drm/panel/Kconfig
+++ b/drivers/gpu/drm/panel/Kconfig
@@ -158,6 +158,13 @@ config DRM_PANEL_SAMSUNG_S6E63J0X03
depends on BACKLIGHT_CLASS_DEVICE
select VIDEOMODE_HELPERS
+config DRM_PANEL_SAMSUNG_S6E63M0
+ tristate "Samsung S6E63M0 RGB/SPI panel"
+ depends on OF
+ depends on SPI
+ depends on BACKLIGHT_CLASS_DEVICE
+ select VIDEOMODE_HELPERS
+
config DRM_PANEL_SAMSUNG_S6E8AA0
tristate "Samsung S6E8AA0 DSI video mode panel"
depends on OF
diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
index 4396658a7996..4507a2d253ac 100644
--- a/drivers/gpu/drm/panel/Makefile
+++ b/drivers/gpu/drm/panel/Makefile
@@ -16,6 +16,7 @@ obj-$(CONFIG_DRM_PANEL_SAMSUNG_LD9040) += panel-samsung-ld9040.o
obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6D16D0) += panel-samsung-s6d16d0.o
obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E3HA2) += panel-samsung-s6e3ha2.o
obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E63J0X03) += panel-samsung-s6e63j0x03.o
+obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E63M0) += panel-samsung-s6e63m0.o
obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E8AA0) += panel-samsung-s6e8aa0.o
obj-$(CONFIG_DRM_PANEL_SEIKO_43WVF1G) += panel-seiko-43wvf1g.o
obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) += panel-sharp-lq101r1sx01.o
diff --git a/drivers/gpu/drm/panel/panel-samsung-s6e63m0.c b/drivers/gpu/drm/panel/panel-samsung-s6e63m0.c
new file mode 100644
index 000000000000..7658bd993088
--- /dev/null
+++ b/drivers/gpu/drm/panel/panel-samsung-s6e63m0.c
@@ -0,0 +1,517 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * S6E63M0 AMOLED LCD drm_panel driver.
+ *
+ * Copyright (C) 2019 Paweł Chmiel <[email protected]>
+ * Derived from drivers/gpu/drm/panel-samsung-ld9040.c
+ *
+ * Andrzej Hajda <[email protected]>
+ */
+
+#include <drm/drm_modes.h>
+#include <drm/drm_panel.h>
+#include <drm/drm_print.h>
+
+#include <linux/backlight.h>
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/regulator/consumer.h>
+#include <linux/spi/spi.h>
+
+#include <video/mipi_display.h>
+#include <video/of_videomode.h>
+#include <video/videomode.h>
+
+/* Manufacturer Command Set */
+#define MCS_ELVSS_ON 0xb1
+#define MCS_ACL_CTRL 0xc0
+#define MCS_DISPLAY_CONDITION 0xf2
+#define MCS_ETC_CONDITION 0xf6
+#define MCS_PANEL_CONDITION 0xF8
+#define MCS_GAMMA_CTRL 0xfa
+
+#define NUM_GAMMA_LEVELS 11
+#define GAMMA_TABLE_COUNT 23
+
+#define DATA_MASK 0x100
+
+#define MAX_BRIGHTNESS (NUM_GAMMA_LEVELS - 1)
+
+/* array of gamma tables for gamma value 2.2 */
+static u8 const s6e63m0_gamma_22[NUM_GAMMA_LEVELS][GAMMA_TABLE_COUNT] = {
+ { MCS_GAMMA_CTRL, 0x00,
+ 0x18, 0x08, 0x24, 0x78, 0xEC, 0x3D, 0xC8,
+ 0xC2, 0xB6, 0xC4, 0xC7, 0xB6, 0xD5, 0xD7,
+ 0xCC, 0x00, 0x39, 0x00, 0x36, 0x00, 0x51 },
+ { MCS_GAMMA_CTRL, 0x00,
+ 0x18, 0x08, 0x24, 0x73, 0x4A, 0x3D, 0xC0,
+ 0xC2, 0xB1, 0xBB, 0xBE, 0xAC, 0xCE, 0xCF,
+ 0xC5, 0x00, 0x5D, 0x00, 0x5E, 0x00, 0x82 },
+ { MCS_GAMMA_CTRL, 0x00,
+ 0x18, 0x08, 0x24, 0x70, 0x51, 0x3E, 0xBF,
+ 0xC1, 0xAF, 0xB9, 0xBC, 0xAB, 0xCC, 0xCC,
+ 0xC2, 0x00, 0x65, 0x00, 0x67, 0x00, 0x8D },
+ { MCS_GAMMA_CTRL, 0x00,
+ 0x18, 0x08, 0x24, 0x6C, 0x54, 0x3A, 0xBC,
+ 0xBF, 0xAC, 0xB7, 0xBB, 0xA9, 0xC9, 0xC9,
+ 0xBE, 0x00, 0x71, 0x00, 0x73, 0x00, 0x9E },
+ { MCS_GAMMA_CTRL, 0x00,
+ 0x18, 0x08, 0x24, 0x69, 0x54, 0x37, 0xBB,
+ 0xBE, 0xAC, 0xB4, 0xB7, 0xA6, 0xC7, 0xC8,
+ 0xBC, 0x00, 0x7B, 0x00, 0x7E, 0x00, 0xAB },
+ { MCS_GAMMA_CTRL, 0x00,
+ 0x18, 0x08, 0x24, 0x66, 0x55, 0x34, 0xBA,
+ 0xBD, 0xAB, 0xB1, 0xB5, 0xA3, 0xC5, 0xC6,
+ 0xB9, 0x00, 0x85, 0x00, 0x88, 0x00, 0xBA },
+ { MCS_GAMMA_CTRL, 0x00,
+ 0x18, 0x08, 0x24, 0x63, 0x53, 0x31, 0xB8,
+ 0xBC, 0xA9, 0xB0, 0xB5, 0xA2, 0xC4, 0xC4,
+ 0xB8, 0x00, 0x8B, 0x00, 0x8E, 0x00, 0xC2 },
+ { MCS_GAMMA_CTRL, 0x00,
+ 0x18, 0x08, 0x24, 0x62, 0x54, 0x30, 0xB9,
+ 0xBB, 0xA9, 0xB0, 0xB3, 0xA1, 0xC1, 0xC3,
+ 0xB7, 0x00, 0x91, 0x00, 0x95, 0x00, 0xDA },
+ { MCS_GAMMA_CTRL, 0x00,
+ 0x18, 0x08, 0x24, 0x66, 0x58, 0x34, 0xB6,
+ 0xBA, 0xA7, 0xAF, 0xB3, 0xA0, 0xC1, 0xC2,
+ 0xB7, 0x00, 0x97, 0x00, 0x9A, 0x00, 0xD1 },
+ { MCS_GAMMA_CTRL, 0x00,
+ 0x18, 0x08, 0x24, 0x64, 0x56, 0x33, 0xB6,
+ 0xBA, 0xA8, 0xAC, 0xB1, 0x9D, 0xC1, 0xC1,
+ 0xB7, 0x00, 0x9C, 0x00, 0x9F, 0x00, 0xD6 },
+ { MCS_GAMMA_CTRL, 0x00,
+ 0x18, 0x08, 0x24, 0x5f, 0x50, 0x2d, 0xB6,
+ 0xB9, 0xA7, 0xAd, 0xB1, 0x9f, 0xbe, 0xC0,
+ 0xB5, 0x00, 0xa0, 0x00, 0xa4, 0x00, 0xdb },
+};
+
+struct s6e63m0 {
+ struct device *dev;
+ struct drm_panel panel;
+ struct backlight_device *bl_dev;
+
+ struct regulator_bulk_data supplies[2];
+ struct gpio_desc *reset_gpio;
+ struct videomode vm;
+
+ bool prepared;
+ bool enabled;
+
+ /*
+ * This field is tested by functions directly accessing bus before
+ * transfer, transfer is skipped if it is set. In case of transfer
+ * failure or unexpected response the field is set to error value.
+ * Such construct allows to eliminate many checks in higher level
+ * functions.
+ */
+ int error;
+};
+
+static const struct drm_display_mode default_mode = {
+ .clock = 25628,
+ .hdisplay = 480,
+ .hsync_start = 480 + 16,
+ .hsync_end = 480 + 16 + 2,
+ .htotal = 480 + 16 + 2 + 16,
+ .vdisplay = 800,
+ .vsync_start = 800 + 28,
+ .vsync_end = 800 + 28 + 2,
+ .vtotal = 800 + 28 + 2 + 1,
+ .vrefresh = 60,
+ .width_mm = 53,
+ .height_mm = 89,
+ .flags = DRM_MODE_FLAG_NVSYNC | DRM_MODE_FLAG_NHSYNC,
+};
+
+static inline struct s6e63m0 *panel_to_s6e63m0(struct drm_panel *panel)
+{
+ return container_of(panel, struct s6e63m0, panel);
+}
+
+static int s6e63m0_clear_error(struct s6e63m0 *ctx)
+{
+ int ret = ctx->error;
+
+ ctx->error = 0;
+ return ret;
+}
+
+static int s6e63m0_spi_write_word(struct s6e63m0 *ctx, u16 data)
+{
+ struct spi_device *spi = to_spi_device(ctx->dev);
+ struct spi_transfer xfer = {
+ .len = 2,
+ .tx_buf = &data,
+ };
+ struct spi_message msg;
+
+ spi_message_init(&msg);
+ spi_message_add_tail(&xfer, &msg);
+
+ return spi_sync(spi, &msg);
+}
+
+static void s6e63m0_dcs_write(struct s6e63m0 *ctx, const u8 *data, size_t len)
+{
+ int ret = 0;
+
+ if (ctx->error < 0 || len == 0)
+ return;
+
+ DRM_DEV_DEBUG(ctx->dev, "writing dcs seq: %*ph\n", (int)len, data);
+ ret = s6e63m0_spi_write_word(ctx, *data);
+
+ while (!ret && --len) {
+ ++data;
+ ret = s6e63m0_spi_write_word(ctx, *data | DATA_MASK);
+ }
+
+ if (ret) {
+ DRM_DEV_ERROR(ctx->dev, "error %d writing dcs seq: %*ph\n", ret,
+ (int)len, data);
+ ctx->error = ret;
+ }
+
+ usleep_range(300, 310);
+}
+
+#define s6e63m0_dcs_write_seq_static(ctx, seq ...) \
+ ({ \
+ static const u8 d[] = { seq }; \
+ s6e63m0_dcs_write(ctx, d, ARRAY_SIZE(d)); \
+ })
+
+static void s6e63m0_brightness_set(struct s6e63m0 *ctx)
+{
+ int brightness = ctx->bl_dev->props.brightness;
+
+ /* disable and set new gamma */
+ s6e63m0_dcs_write(ctx, s6e63m0_gamma_22[brightness],
+ ARRAY_SIZE(s6e63m0_gamma_22[brightness]));
+
+ /* update gamma table. */
+ s6e63m0_dcs_write_seq_static(ctx, MCS_GAMMA_CTRL, 0x01);
+}
+
+static void s6e63m0_init(struct s6e63m0 *ctx)
+{
+ s6e63m0_dcs_write_seq_static(ctx, MCS_PANEL_CONDITION,
+ 0x01, 0x27, 0x27, 0x07, 0x07, 0x54, 0x9f,
+ 0x63, 0x86, 0x1a, 0x33, 0x0d, 0x00, 0x00);
+
+ s6e63m0_dcs_write_seq_static(ctx, MCS_DISPLAY_CONDITION,
+ 0x02, 0x03, 0x1c, 0x10, 0x10);
+ s6e63m0_dcs_write_seq_static(ctx, 0xf7,
+ 0x03, 0x00, 0x00);
+
+ s6e63m0_dcs_write_seq_static(ctx, MCS_GAMMA_CTRL,
+ 0x00, 0x18, 0x08, 0x24, 0x64, 0x56, 0x33,
+ 0xb6, 0xba, 0xa8, 0xac, 0xb1, 0x9d, 0xc1,
+ 0xc1, 0xb7, 0x00, 0x9c, 0x00, 0x9f, 0x00,
+ 0xd6);
+ s6e63m0_dcs_write_seq_static(ctx, MCS_GAMMA_CTRL,
+ 0x01);
+
+ s6e63m0_dcs_write_seq_static(ctx, MCS_ETC_CONDITION,
+ 0x00, 0x8c, 0x07);
+ s6e63m0_dcs_write_seq_static(ctx, 0xb3,
+ 0xc);
+
+ s6e63m0_dcs_write_seq_static(ctx, 0xb5,
+ 0x2c, 0x12, 0x0c, 0x0a, 0x10, 0x0e, 0x17,
+ 0x13, 0x1f, 0x1a, 0x2a, 0x24, 0x1f, 0x1b,
+ 0x1a, 0x17, 0x2b, 0x26, 0x22, 0x20, 0x3a,
+ 0x34, 0x30, 0x2c, 0x29, 0x26, 0x25, 0x23,
+ 0x21, 0x20, 0x1e, 0x1e);
+
+ s6e63m0_dcs_write_seq_static(ctx, 0xb6,
+ 0x00, 0x00, 0x11, 0x22, 0x33, 0x44, 0x44,
+ 0x44, 0x55, 0x55, 0x66, 0x66, 0x66, 0x66,
+ 0x66, 0x66);
+
+ s6e63m0_dcs_write_seq_static(ctx, 0xb7,
+ 0x2c, 0x12, 0x0c, 0x0a, 0x10, 0x0e, 0x17,
+ 0x13, 0x1f, 0x1a, 0x2a, 0x24, 0x1f, 0x1b,
+ 0x1a, 0x17, 0x2b, 0x26, 0x22, 0x20, 0x3a,
+ 0x34, 0x30, 0x2c, 0x29, 0x26, 0x25, 0x23,
+ 0x21, 0x20, 0x1e, 0x1e, 0x00, 0x00, 0x11,
+ 0x22, 0x33, 0x44, 0x44, 0x44, 0x55, 0x55,
+ 0x66, 0x66, 0x66, 0x66, 0x66, 0x66);
+
+ s6e63m0_dcs_write_seq_static(ctx, 0xb9,
+ 0x2c, 0x12, 0x0c, 0x0a, 0x10, 0x0e, 0x17,
+ 0x13, 0x1f, 0x1a, 0x2a, 0x24, 0x1f, 0x1b,
+ 0x1a, 0x17, 0x2b, 0x26, 0x22, 0x20, 0x3a,
+ 0x34, 0x30, 0x2c, 0x29, 0x26, 0x25, 0x23,
+ 0x21, 0x20, 0x1e, 0x1e);
+
+ s6e63m0_dcs_write_seq_static(ctx, 0xba,
+ 0x00, 0x00, 0x11, 0x22, 0x33, 0x44, 0x44,
+ 0x44, 0x55, 0x55, 0x66, 0x66, 0x66, 0x66,
+ 0x66, 0x66);
+
+ s6e63m0_dcs_write_seq_static(ctx, 0xc1,
+ 0x4d, 0x96, 0x1d, 0x00, 0x00, 0x01, 0xdf,
+ 0x00, 0x00, 0x03, 0x1f, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x03, 0x06,
+ 0x09, 0x0d, 0x0f, 0x12, 0x15, 0x18);
+
+ s6e63m0_dcs_write_seq_static(ctx, 0xb2,
+ 0x10, 0x10, 0x0b, 0x05);
+
+ s6e63m0_dcs_write_seq_static(ctx, MCS_ACL_CTRL,
+ 0x01);
+
+ s6e63m0_dcs_write_seq_static(ctx, MCS_ELVSS_ON,
+ 0x0b);
+
+ s6e63m0_dcs_write_seq_static(ctx, MIPI_DCS_EXIT_SLEEP_MODE);
+}
+
+static int s6e63m0_power_on(struct s6e63m0 *ctx)
+{
+ int ret;
+
+ gpiod_set_value(ctx->reset_gpio, 0);
+ msleep(120);
+
+ ret = regulator_bulk_enable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
+ if (ret < 0)
+ return ret;
+
+ msleep(25);
+
+ return 0;
+}
+
+static int s6e63m0_power_off(struct s6e63m0 *ctx)
+{
+ int ret;
+
+ ret = regulator_bulk_disable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
+ if (ret < 0)
+ return ret;
+
+ gpiod_set_value(ctx->reset_gpio, 1);
+ msleep(120);
+
+ return 0;
+}
+
+static int s6e63m0_disable(struct drm_panel *panel)
+{
+ struct s6e63m0 *ctx = panel_to_s6e63m0(panel);
+
+ if (!ctx->enabled)
+ return 0;
+
+ backlight_disable(ctx->bl_dev);
+
+ s6e63m0_dcs_write_seq_static(ctx, MIPI_DCS_ENTER_SLEEP_MODE);
+ msleep(200);
+
+ ctx->enabled = false;
+
+ return 0;
+}
+
+static int s6e63m0_unprepare(struct drm_panel *panel)
+{
+ struct s6e63m0 *ctx = panel_to_s6e63m0(panel);
+ int ret;
+
+ if (!ctx->prepared)
+ return 0;
+
+ s6e63m0_clear_error(ctx);
+
+ ret = s6e63m0_power_off(ctx);
+ if (ret < 0)
+ return ret;
+
+ ctx->prepared = false;
+
+ return 0;
+}
+
+static int s6e63m0_prepare(struct drm_panel *panel)
+{
+ struct s6e63m0 *ctx = panel_to_s6e63m0(panel);
+ int ret;
+
+ if (ctx->prepared)
+ return 0;
+
+ ret = s6e63m0_power_on(ctx);
+ if (ret < 0)
+ return ret;
+
+ s6e63m0_init(ctx);
+
+ ret = s6e63m0_clear_error(ctx);
+
+ if (ret < 0)
+ s6e63m0_unprepare(panel);
+
+ ctx->prepared = true;
+
+ return ret;
+}
+
+static int s6e63m0_enable(struct drm_panel *panel)
+{
+ struct s6e63m0 *ctx = panel_to_s6e63m0(panel);
+
+ if (ctx->enabled)
+ return 0;
+
+ s6e63m0_dcs_write_seq_static(ctx, MIPI_DCS_SET_DISPLAY_ON);
+
+ backlight_enable(ctx->bl_dev);
+
+ ctx->enabled = true;
+
+ return 0;
+}
+
+static int s6e63m0_get_modes(struct drm_panel *panel)
+{
+ struct drm_connector *connector = panel->connector;
+ struct drm_display_mode *mode;
+
+ mode = drm_mode_duplicate(panel->drm, &default_mode);
+ if (!mode) {
+ DRM_ERROR("failed to add mode %ux%ux@%u\n",
+ default_mode.hdisplay, default_mode.vdisplay,
+ default_mode.vrefresh);
+ return -ENOMEM;
+ }
+
+ drm_mode_set_name(mode);
+
+ mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
+ drm_mode_probed_add(connector, mode);
+
+ return 1;
+}
+
+static const struct drm_panel_funcs s6e63m0_drm_funcs = {
+ .disable = s6e63m0_disable,
+ .unprepare = s6e63m0_unprepare,
+ .prepare = s6e63m0_prepare,
+ .enable = s6e63m0_enable,
+ .get_modes = s6e63m0_get_modes,
+};
+
+static int s6e63m0_set_brightness(struct backlight_device *bd)
+{
+ struct s6e63m0 *ctx = bl_get_data(bd);
+
+ s6e63m0_brightness_set(ctx);
+
+ return s6e63m0_clear_error(ctx);
+}
+
+static const struct backlight_ops s6e63m0_backlight_ops = {
+ .update_status = s6e63m0_set_brightness,
+};
+
+static void s6e63m0_backlight_register(struct s6e63m0 *ctx)
+{
+ struct backlight_properties props = {
+ .type = BACKLIGHT_RAW,
+ .brightness = MAX_BRIGHTNESS,
+ .max_brightness = MAX_BRIGHTNESS
+ };
+ struct device *dev = ctx->dev;
+
+ ctx->bl_dev = devm_backlight_device_register(dev, "panel", dev, ctx,
+ &s6e63m0_backlight_ops,
+ &props);
+ if (IS_ERR(ctx->bl_dev))
+ DRM_DEV_ERROR(dev, "error registering backlight device (%ld)\n",
+ PTR_ERR(ctx->bl_dev));
+}
+
+static int s6e63m0_probe(struct spi_device *spi)
+{
+ struct device *dev = &spi->dev;
+ struct s6e63m0 *ctx;
+ int ret;
+
+ ctx = devm_kzalloc(dev, sizeof(struct s6e63m0), GFP_KERNEL);
+ if (!ctx)
+ return -ENOMEM;
+
+ spi_set_drvdata(spi, ctx);
+
+ ctx->dev = dev;
+ ctx->enabled = false;
+ ctx->prepared = false;
+
+ ctx->supplies[0].supply = "vdd3";
+ ctx->supplies[1].supply = "vci";
+ ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ctx->supplies),
+ ctx->supplies);
+ if (ret < 0) {
+ DRM_DEV_ERROR(dev, "failed to get regulators: %d\n", ret);
+ return ret;
+ }
+
+ ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
+ if (IS_ERR(ctx->reset_gpio)) {
+ DRM_DEV_ERROR(dev, "cannot get reset-gpios %ld\n",
+ PTR_ERR(ctx->reset_gpio));
+ return PTR_ERR(ctx->reset_gpio);
+ }
+
+ spi->bits_per_word = 9;
+ spi->mode = SPI_MODE_3;
+ ret = spi_setup(spi);
+ if (ret < 0) {
+ DRM_DEV_ERROR(dev, "spi setup failed.\n");
+ return ret;
+ }
+
+ drm_panel_init(&ctx->panel);
+ ctx->panel.dev = dev;
+ ctx->panel.funcs = &s6e63m0_drm_funcs;
+
+ ret = drm_panel_add(&ctx->panel);
+ if (ret < 0)
+ return ret;
+
+ s6e63m0_backlight_register(ctx);
+
+ return 0;
+}
+
+static int s6e63m0_remove(struct spi_device *spi)
+{
+ struct s6e63m0 *ctx = spi_get_drvdata(spi);
+
+ drm_panel_remove(&ctx->panel);
+
+ return 0;
+}
+
+static const struct of_device_id s6e63m0_of_match[] = {
+ { .compatible = "samsung,s6e63m0" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, s6e63m0_of_match);
+
+static struct spi_driver s6e63m0_driver = {
+ .probe = s6e63m0_probe,
+ .remove = s6e63m0_remove,
+ .driver = {
+ .name = "panel-samsung-s6e63m0",
+ .of_match_table = s6e63m0_of_match,
+ },
+};
+module_spi_driver(s6e63m0_driver);
+
+MODULE_AUTHOR("Paweł Chmiel <[email protected]>");
+MODULE_DESCRIPTION("s6e63m0 LCD Driver");
+MODULE_LICENSE("GPL v2");
--
2.17.1
Hi Paweł
Looks good, thanks for addressing all the review feedback.
On Fri, Feb 01, 2019 at 06:28:52PM +0100, Paweł Chmiel wrote:
> This patch adds Samsung S6E63M0 AMOLED LCD panel driver, connected over
> spi. It's based on already removed, non dt s6e63m0 driver and
> panel-samsung-ld9040. It can be found for example in some of Samsung
> Aries based phones.
>
> Signed-off-by: Paweł Chmiel <[email protected]>
If you consider (do not change unless you think it better) the
following nits than you can add my:
Reviewed-by: Sam Ravnborg <[email protected]>
Sam
> diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
> index 3f3537719beb..be05ed5218eb 100644
> --- a/drivers/gpu/drm/panel/Kconfig
> +++ b/drivers/gpu/drm/panel/Kconfig
> @@ -158,6 +158,13 @@ config DRM_PANEL_SAMSUNG_S6E63J0X03
> depends on BACKLIGHT_CLASS_DEVICE
> select VIDEOMODE_HELPERS
>
> +config DRM_PANEL_SAMSUNG_S6E63M0
> + tristate "Samsung S6E63M0 RGB/SPI panel"
> + depends on OF
> + depends on SPI
> + depends on BACKLIGHT_CLASS_DEVICE
> + select VIDEOMODE_HELPERS
With the use of display_mode the above "select VIDEOMODE_HELPERS"
is likely no longer required. Please check.
A help text would be nice.
> +
> config DRM_PANEL_SAMSUNG_S6E8AA0
> tristate "Samsung S6E8AA0 DSI video mode panel"
> depends on OF
> +#include <video/of_videomode.h>
> +#include <video/videomode.h>
Please check if these two files are required.
> +struct s6e63m0 {
> + struct device *dev;
> + struct drm_panel panel;
> + struct backlight_device *bl_dev;
> +
> + struct regulator_bulk_data supplies[2];
> + struct gpio_desc *reset_gpio;
> + struct videomode vm;
vm is no longer used - delete it.
> +
> + bool prepared;
> + bool enabled;
> +
> + /*
> + * This field is tested by functions directly accessing bus before
> + * transfer, transfer is skipped if it is set. In case of transfer
> + * failure or unexpected response the field is set to error value.
> + * Such construct allows to eliminate many checks in higher level
> + * functions.
> + */
> + int error;
> +};
> +
> +static int s6e63m0_get_modes(struct drm_panel *panel)
> +{
> + struct drm_connector *connector = panel->connector;
> + struct drm_display_mode *mode;
> +
> + mode = drm_mode_duplicate(panel->drm, &default_mode);
> + if (!mode) {
> + DRM_ERROR("failed to add mode %ux%ux@%u\n",
> + default_mode.hdisplay, default_mode.vdisplay,
> + default_mode.vrefresh);
I recall I have seen a generic way to print the above,
but I have failed to find it.
Maybe it is just my memory that fools me.
The above is fine.
> +
> + s6e63m0_backlight_register(ctx);
Is it correct that we continue even if we fail to register backlight?
> +
> + return 0;
> +}
> +
> +
> +static const struct of_device_id s6e63m0_of_match[] = {
> + { .compatible = "samsung,s6e63m0" },
> + { }
Add /* sentinel */ comment?
> +};
On piątek, 1 lutego 2019 22:36:07 CET Sam Ravnborg wrote:
> Hi Paweł
>
> Looks good, thanks for addressing all the review feedback.
>
> On Fri, Feb 01, 2019 at 06:28:52PM +0100, Paweł Chmiel wrote:
> > This patch adds Samsung S6E63M0 AMOLED LCD panel driver, connected over
> > spi. It's based on already removed, non dt s6e63m0 driver and
> > panel-samsung-ld9040. It can be found for example in some of Samsung
> > Aries based phones.
> >
> > Signed-off-by: Paweł Chmiel <[email protected]>
> If you consider (do not change unless you think it better) the
> following nits than you can add my:
>
> Reviewed-by: Sam Ravnborg <[email protected]>
>
> Sam
>
> > diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
> > index 3f3537719beb..be05ed5218eb 100644
> > --- a/drivers/gpu/drm/panel/Kconfig
> > +++ b/drivers/gpu/drm/panel/Kconfig
> > @@ -158,6 +158,13 @@ config DRM_PANEL_SAMSUNG_S6E63J0X03
> > depends on BACKLIGHT_CLASS_DEVICE
> > select VIDEOMODE_HELPERS
> >
> > +config DRM_PANEL_SAMSUNG_S6E63M0
> > + tristate "Samsung S6E63M0 RGB/SPI panel"
> > + depends on OF
> > + depends on SPI
> > + depends on BACKLIGHT_CLASS_DEVICE
> > + select VIDEOMODE_HELPERS
> With the use of display_mode the above "select VIDEOMODE_HELPERS"
> is likely no longer required. Please check.
Confirmed that it's not needed now.
>
> A help text would be nice.
Simple help text added.
>
> > +
> > config DRM_PANEL_SAMSUNG_S6E8AA0
> > tristate "Samsung S6E8AA0 DSI video mode panel"
> > depends on OF
>
>
> > +#include <video/of_videomode.h>
> > +#include <video/videomode.h>
> Please check if these two files are required.
Removed.
>
> > +struct s6e63m0 {
> > + struct device *dev;
> > + struct drm_panel panel;
> > + struct backlight_device *bl_dev;
> > +
> > + struct regulator_bulk_data supplies[2];
> > + struct gpio_desc *reset_gpio;
> > + struct videomode vm;
> vm is no longer used - delete it.
Removed.
>
> > +
> > + bool prepared;
> > + bool enabled;
> > +
> > + /*
> > + * This field is tested by functions directly accessing bus before
> > + * transfer, transfer is skipped if it is set. In case of transfer
> > + * failure or unexpected response the field is set to error value.
> > + * Such construct allows to eliminate many checks in higher level
> > + * functions.
> > + */
> > + int error;
> > +};
> > +
>
> > +static int s6e63m0_get_modes(struct drm_panel *panel)
> > +{
> > + struct drm_connector *connector = panel->connector;
> > + struct drm_display_mode *mode;
> > +
> > + mode = drm_mode_duplicate(panel->drm, &default_mode);
> > + if (!mode) {
> > + DRM_ERROR("failed to add mode %ux%ux@%u\n",
> > + default_mode.hdisplay, default_mode.vdisplay,
> > + default_mode.vrefresh);
> I recall I have seen a generic way to print the above,
> but I have failed to find it.
> Maybe it is just my memory that fools me.
>
> The above is fine.
>
> > +
> > + s6e63m0_backlight_register(ctx);
>
> Is it correct that we continue even if we fail to register backlight?
Fixed, now errors are handled and it's called before adding drm panel,
so we won't do this if there will be any error during backlight setup.
>
>
> > +
> > + return 0;
> > +}
> > +
> > +
> > +static const struct of_device_id s6e63m0_of_match[] = {
> > + { .compatible = "samsung,s6e63m0" },
> > + { }
>
> Add /* sentinel */ comment?
Added
>
> > +};
>
>
I'll be sending v3 version with all issues fixed. It would be nice to have this tested on Samsung Goni.
Thanks for all comments