It's a 5.5" 720x1440 TFT LCD MIPI DSI panel with built in touchscreen and
backlight as found in the Librem 5 devkit.
These patches are against linux next as of 2019-02-08.
Changes from v1
* As per review comments from Sam Ravnborg
* Make SPDX-License-Identifier match MODULE_LICENSE
* Sort include files alphabetically
* Drop drmP.h and use individual includes
* Drop superfuous 'x' in mode printout on error path
* Allpixelson_set: Add proper space around '*'
* Drop superfluous put_device(&ctx->backlight->dev);
* Add /* Sentinel */ in jh057n_of_match
* Drop jh057n->enabled
* Drop drm_display_info_set_bus_formats
* Kconfig: Depend on BACKLIGHT_CLASS_DEVICE which somehow got lost
* Move jh057n_enable close to jh057n_disable
Guido Günther (3):
dt-bindings: Add vendor prefix for ROCKTECH DISPLAYS LIMITED
dt-bindings: Add Rocktech jh057n00900 panel bindings
drm/panel: Add Rocktech jh057n00900 panel driver
.../display/panel/rocktech,jh057n00900.txt | 18 +
.../devicetree/bindings/vendor-prefixes.txt | 1 +
drivers/gpu/drm/panel/Kconfig | 13 +
drivers/gpu/drm/panel/Makefile | 1 +
.../drm/panel/panel-rocktech-jh057n00900.c | 385 ++++++++++++++++++
5 files changed, 418 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/panel/rocktech,jh057n00900.txt
create mode 100644 drivers/gpu/drm/panel/panel-rocktech-jh057n00900.c
--
2.20.1
The Rocktec jh057n00900 is a 5.5" MIPI DSI video mode panel with a
720x1440 resolution and a built in backlight.
Signed-off-by: Guido Günther <[email protected]>
---
.../display/panel/rocktech,jh057n00900.txt | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/panel/rocktech,jh057n00900.txt
diff --git a/Documentation/devicetree/bindings/display/panel/rocktech,jh057n00900.txt b/Documentation/devicetree/bindings/display/panel/rocktech,jh057n00900.txt
new file mode 100644
index 000000000000..32f4001d2d6f
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/rocktech,jh057n00900.txt
@@ -0,0 +1,18 @@
+Rocktech jh057n00900 5.5" 720x1440 TFT LCD panel
+
+Required properties:
+- compatible: should be "rocktech,jh057n00900"
+- reg: DSI virtual channel of the peripheral
+- reset-gpios: panel reset gpio
+- backlight: phandle of the backlight device attached to the panel
+
+Example:
+
+ &mipi_dsi {
+ panel {
+ compatible = "rocktech,jh057n00900";
+ reg = <0>;
+ backlight = <&backlight>;
+ reset-gpios = <&gpio3 13 GPIO_ACTIVE_LOW>;
+ };
+ };
--
2.20.1
Support Rocktech jh057n00900 5.5" 720x1440 TFT LCD panel. It is a MIPI
DSI video mode panel.
The panel seems to use a Sitronix ST7703 look alike (most of the
commands look similar to the ST7703's data sheet but use a different
number of parameters). The initial version of the DSI init sequence
(including sleeps) were provided by the vendor. Sleeps were reduced
considerably though to speed up initialization.
Signed-off-by: Guido Günther <[email protected]>
Cc: [email protected]
---
drivers/gpu/drm/panel/Kconfig | 13 +
drivers/gpu/drm/panel/Makefile | 1 +
.../drm/panel/panel-rocktech-jh057n00900.c | 385 ++++++++++++++++++
3 files changed, 399 insertions(+)
create mode 100644 drivers/gpu/drm/panel/panel-rocktech-jh057n00900.c
diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
index 3e070153ef21..42f541fe57ae 100644
--- a/drivers/gpu/drm/panel/Kconfig
+++ b/drivers/gpu/drm/panel/Kconfig
@@ -149,6 +149,19 @@ config DRM_PANEL_RAYDIUM_RM68200
Say Y here if you want to enable support for Raydium RM68200
720x1280 DSI video mode panel.
+config DRM_PANEL_ROCKTECH_JH057N00900
+ tristate "Rocktech JH057N00900 MIPI touchscreen panel"
+ depends on OF
+ depends on DRM_MIPI_DSI
+ depends on BACKLIGHT_CLASS_DEVICE
+ help
+ Say Y here if you want to enable support for Rocktech JH057N00900
+ MIPI DSI panel as e.g. used in the Librem 5 devkit. It has a
+ resolution of 720x1440 pixels, a built in backlight and touch
+ controller.
+ Touch input support is provided by the goodix driver and needs to be
+ selected separately.
+
config DRM_PANEL_SAMSUNG_S6D16D0
tristate "Samsung S6D16D0 DSI video mode panel"
depends on OF
diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
index e7ab71968bbf..902e871059d0 100644
--- a/drivers/gpu/drm/panel/Makefile
+++ b/drivers/gpu/drm/panel/Makefile
@@ -13,6 +13,7 @@ obj-$(CONFIG_DRM_PANEL_ORISETECH_OTM8009A) += panel-orisetech-otm8009a.o
obj-$(CONFIG_DRM_PANEL_PANASONIC_VVX10F034N00) += panel-panasonic-vvx10f034n00.o
obj-$(CONFIG_DRM_PANEL_RASPBERRYPI_TOUCHSCREEN) += panel-raspberrypi-touchscreen.o
obj-$(CONFIG_DRM_PANEL_RAYDIUM_RM68200) += panel-raydium-rm68200.o
+obj-$(CONFIG_DRM_PANEL_ROCKTECH_JH057N00900) += panel-rocktech-jh057n00900.o
obj-$(CONFIG_DRM_PANEL_SAMSUNG_LD9040) += panel-samsung-ld9040.o
obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6D16D0) += panel-samsung-s6d16d0.o
obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E3HA2) += panel-samsung-s6e3ha2.o
diff --git a/drivers/gpu/drm/panel/panel-rocktech-jh057n00900.c b/drivers/gpu/drm/panel/panel-rocktech-jh057n00900.c
new file mode 100644
index 000000000000..7df72040a90d
--- /dev/null
+++ b/drivers/gpu/drm/panel/panel-rocktech-jh057n00900.c
@@ -0,0 +1,385 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Rockteck jh057n00900 5.5" MIPI-DSI panel driver
+ *
+ * Copyright (C) Purism SPC 2019
+ */
+
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_modes.h>
+#include <drm/drm_panel.h>
+#include <drm/drm_print.h>
+#include <linux/backlight.h>
+#include <linux/debugfs.h>
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/media-bus-format.h>
+#include <linux/module.h>
+#include <video/display_timing.h>
+#include <video/mipi_display.h>
+
+#define DRV_NAME "jh057n00900"
+
+/* Manufacturer specific Commands send via DSI */
+#define ST7703_CMD_ALL_PIXEL_OFF 0x22
+#define ST7703_CMD_ALL_PIXEL_ON 0x23
+#define ST7703_CMD_SETDISP 0xB2
+#define ST7703_CMD_SETRGBIF 0xB3
+#define ST7703_CMD_SETCYC 0xB4
+#define ST7703_CMD_SETBGP 0xB5
+#define ST7703_CMD_SETVCOM 0xB6
+#define ST7703_CMD_SETOTP 0xB7
+#define ST7703_CMD_SETPOWER_EXT 0xB8
+#define ST7703_CMD_SETEXTC 0xB9
+#define ST7703_CMD_SETMIPI 0xBA
+#define ST7703_CMD_SETVDC 0xBC
+#define ST7703_CMD_SETSCR 0xC0
+#define ST7703_CMD_SETPOWER 0xC1
+#define ST7703_CMD_SETPANEL 0xCC
+#define ST7703_CMD_SETGAMMA 0xE0
+#define ST7703_CMD_SETEQ 0xE3
+#define ST7703_CMD_SETGIP1 0xE9
+#define ST7703_CMD_SETGIP2 0xEA
+
+struct jh057n {
+ struct device *dev;
+ struct drm_panel panel;
+ struct gpio_desc *reset_gpio;
+ struct backlight_device *backlight;
+ bool prepared;
+
+ struct dentry *debugfs;
+};
+
+static inline struct jh057n *panel_to_jh057n(struct drm_panel *panel)
+{
+ return container_of(panel, struct jh057n, panel);
+}
+
+#define dsi_generic_write_seq(dsi, seq...) do { \
+ static const u8 d[] = { seq }; \
+ int ret; \
+ ret = mipi_dsi_generic_write(dsi, d, ARRAY_SIZE(d)); \
+ if (ret < 0) \
+ return ret; \
+ } while (0)
+
+static int jh057n_init_sequence(struct jh057n *ctx)
+{
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
+ struct device *dev = ctx->dev;
+ int ret;
+
+ /*
+ * Init sequence was supplied by the panel vendor. Most of the commands
+ * resemble the ST7703 but the number of parameters often don't match
+ * so it's likely a clone.
+ */
+ dsi_generic_write_seq(dsi, ST7703_CMD_SETEXTC,
+ 0xF1, 0x12, 0x83);
+ dsi_generic_write_seq(dsi, ST7703_CMD_SETRGBIF,
+ 0x10, 0x10, 0x05, 0x05, 0x03, 0xFF, 0x00, 0x00,
+ 0x00, 0x00);
+ dsi_generic_write_seq(dsi, ST7703_CMD_SETSCR,
+ 0x73, 0x73, 0x50, 0x50, 0x00, 0x00, 0x08, 0x70,
+ 0x00);
+ dsi_generic_write_seq(dsi, ST7703_CMD_SETVDC, 0x4E);
+ dsi_generic_write_seq(dsi, ST7703_CMD_SETPANEL, 0x0B);
+ dsi_generic_write_seq(dsi, ST7703_CMD_SETCYC, 0x80);
+ dsi_generic_write_seq(dsi, ST7703_CMD_SETDISP, 0xF0, 0x12, 0x30);
+ dsi_generic_write_seq(dsi, ST7703_CMD_SETEQ,
+ 0x07, 0x07, 0x0B, 0x0B, 0x03, 0x0B, 0x00, 0x00,
+ 0x00, 0x00, 0xFF, 0x00, 0xC0, 0x10);
+ dsi_generic_write_seq(dsi, ST7703_CMD_SETBGP, 0x08, 0x08);
+ msleep(20);
+
+ dsi_generic_write_seq(dsi, ST7703_CMD_SETVCOM, 0x3F, 0x3F);
+ dsi_generic_write_seq(dsi, 0xBF, 0x02, 0x11, 0x00);
+ dsi_generic_write_seq(dsi, ST7703_CMD_SETGIP1,
+ 0x82, 0x10, 0x06, 0x05, 0x9E, 0x0A, 0xA5, 0x12,
+ 0x31, 0x23, 0x37, 0x83, 0x04, 0xBC, 0x27, 0x38,
+ 0x0C, 0x00, 0x03, 0x00, 0x00, 0x00, 0x0C, 0x00,
+ 0x03, 0x00, 0x00, 0x00, 0x75, 0x75, 0x31, 0x88,
+ 0x88, 0x88, 0x88, 0x88, 0x88, 0x13, 0x88, 0x64,
+ 0x64, 0x20, 0x88, 0x88, 0x88, 0x88, 0x88, 0x88,
+ 0x02, 0x88, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00);
+ dsi_generic_write_seq(dsi, ST7703_CMD_SETGIP2,
+ 0x02, 0x21, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x02, 0x46, 0x02, 0x88,
+ 0x88, 0x88, 0x88, 0x88, 0x88, 0x64, 0x88, 0x13,
+ 0x57, 0x13, 0x88, 0x88, 0x88, 0x88, 0x88, 0x88,
+ 0x75, 0x88, 0x23, 0x14, 0x00, 0x00, 0x02, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x30, 0x0A,
+ 0xA5, 0x00, 0x00, 0x00, 0x00);
+ dsi_generic_write_seq(dsi, ST7703_CMD_SETGAMMA,
+ 0x00, 0x09, 0x0E, 0x29, 0x2D, 0x3C, 0x41, 0x37,
+ 0x07, 0x0B, 0x0D, 0x10, 0x11, 0x0F, 0x10, 0x11,
+ 0x18, 0x00, 0x09, 0x0E, 0x29, 0x2D, 0x3C, 0x41,
+ 0x37, 0x07, 0x0B, 0x0D, 0x10, 0x11, 0x0F, 0x10,
+ 0x11, 0x18);
+ msleep(20);
+
+ ret = mipi_dsi_dcs_exit_sleep_mode(dsi);
+ if (ret < 0) {
+ DRM_DEV_ERROR(dev, "Failed to exit sleep mode");
+ return ret;
+ }
+ /* Panel is operational 120 msec after reset */
+ msleep(60);
+ ret = mipi_dsi_dcs_set_display_on(dsi);
+ if (ret)
+ return ret;
+
+ DRM_DEV_DEBUG_DRIVER(dev, "Panel init sequence done");
+ return 0;
+}
+
+static int jh057n_enable(struct drm_panel *panel)
+{
+ struct jh057n *ctx = panel_to_jh057n(panel);
+
+ return backlight_enable(ctx->backlight);
+}
+
+static int jh057n_disable(struct drm_panel *panel)
+{
+ struct jh057n *ctx = panel_to_jh057n(panel);
+
+ return backlight_disable(ctx->backlight);
+}
+
+static int jh057n_unprepare(struct drm_panel *panel)
+{
+ struct jh057n *ctx = panel_to_jh057n(panel);
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
+
+ if (!ctx->prepared)
+ return 0;
+
+ mipi_dsi_dcs_set_display_off(dsi);
+ ctx->prepared = false;
+
+ return 0;
+}
+
+static int jh057n_prepare(struct drm_panel *panel)
+{
+ struct jh057n *ctx = panel_to_jh057n(panel);
+ int ret;
+
+ if (ctx->prepared)
+ return 0;
+
+ DRM_DEV_DEBUG_DRIVER(ctx->dev, "Resetting the panel.");
+ gpiod_set_value_cansleep(ctx->reset_gpio, 1);
+ usleep_range(20, 40);
+ gpiod_set_value_cansleep(ctx->reset_gpio, 0);
+ msleep(20);
+
+ ret = jh057n_init_sequence(ctx);
+ if (ret < 0) {
+ DRM_DEV_ERROR(ctx->dev, "Panel init sequence failed: %d", ret);
+ return ret;
+ }
+
+ ctx->prepared = true;
+
+ return 0;
+}
+
+static const struct drm_display_mode default_mode = {
+ .hdisplay = 720,
+ .hsync_start = 720 + 90,
+ .hsync_end = 720 + 90 + 20,
+ .htotal = 720 + 90 + 20 + 20,
+ .vdisplay = 1440,
+ .vsync_start = 1440 + 20,
+ .vsync_end = 1440 + 20 + 4,
+ .vtotal = 1440 + 20 + 4 + 12,
+ .vrefresh = 60,
+ .clock = 75276,
+ .flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
+ .width_mm = 65,
+ .height_mm = 130,
+};
+
+static int jh057n_get_modes(struct drm_panel *panel)
+{
+ struct drm_display_mode *mode;
+
+ mode = drm_mode_duplicate(panel->drm, &default_mode);
+ if (!mode) {
+ DRM_ERROR("Failed to add mode %ux%u@%u",
+ default_mode.hdisplay, default_mode.vdisplay,
+ default_mode.vrefresh);
+ return -ENOMEM;
+ }
+
+ drm_mode_set_name(mode);
+
+ mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
+ panel->connector->display_info.width_mm = mode->width_mm;
+ panel->connector->display_info.height_mm = mode->height_mm;
+ drm_mode_probed_add(panel->connector, mode);
+
+ return 1;
+}
+
+static const struct drm_panel_funcs jh057n_drm_funcs = {
+ .disable = jh057n_disable,
+ .unprepare = jh057n_unprepare,
+ .prepare = jh057n_prepare,
+ .enable = jh057n_enable,
+ .get_modes = jh057n_get_modes,
+};
+
+static int allpixelson_set(void *data, u64 val)
+{
+ struct jh057n *ctx = data;
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
+
+ DRM_DEV_DEBUG_DRIVER(ctx->dev, "Setting all pixels on");
+ dsi_generic_write_seq(dsi, ST7703_CMD_ALL_PIXEL_ON);
+ msleep(val * 1000);
+ /* Reset the panel to get video back */
+ drm_panel_disable(&ctx->panel);
+ drm_panel_unprepare(&ctx->panel);
+ drm_panel_prepare(&ctx->panel);
+ drm_panel_enable(&ctx->panel);
+
+ return 0;
+}
+
+DEFINE_SIMPLE_ATTRIBUTE(allpixelson_fops, NULL,
+ allpixelson_set, "%llu\n");
+
+static int jh057n_debugfs_init(struct jh057n *ctx)
+{
+ struct dentry *f;
+
+ ctx->debugfs = debugfs_create_dir(DRV_NAME, NULL);
+ if (!ctx->debugfs)
+ return -ENOMEM;
+
+ f = debugfs_create_file("allpixelson", 0600,
+ ctx->debugfs, ctx, &allpixelson_fops);
+ if (!f)
+ return -ENOMEM;
+
+ return 0;
+}
+
+static void jh057n_debugfs_remove(struct jh057n *ctx)
+{
+ debugfs_remove_recursive(ctx->debugfs);
+ ctx->debugfs = NULL;
+}
+
+static int jh057n_probe(struct mipi_dsi_device *dsi)
+{
+ struct device *dev = &dsi->dev;
+ struct jh057n *ctx;
+ int ret;
+
+ ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
+ if (!ctx)
+ return -ENOMEM;
+
+ ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
+ if (IS_ERR(ctx->reset_gpio)) {
+ DRM_DEV_ERROR(dev, "cannot get reset gpio");
+ return PTR_ERR(ctx->reset_gpio);
+ }
+
+ mipi_dsi_set_drvdata(dsi, ctx);
+
+ ctx->dev = dev;
+
+ dsi->lanes = 4;
+ dsi->format = MIPI_DSI_FMT_RGB888;
+ dsi->mode_flags = MIPI_DSI_MODE_VIDEO |
+ MIPI_DSI_MODE_VIDEO_BURST | MIPI_DSI_MODE_VIDEO_SYNC_PULSE;
+
+ ctx->backlight = devm_of_find_backlight(dev);
+ if (IS_ERR(ctx->backlight))
+ return PTR_ERR(ctx->backlight);
+
+ drm_panel_init(&ctx->panel);
+ ctx->panel.dev = dev;
+ ctx->panel.funcs = &jh057n_drm_funcs;
+
+ drm_panel_add(&ctx->panel);
+
+ ret = mipi_dsi_attach(dsi);
+ if (ret < 0) {
+ DRM_DEV_ERROR(dev, "mipi_dsi_attach failed. Is host ready?");
+ drm_panel_remove(&ctx->panel);
+ return ret;
+ }
+
+ DRM_INFO(DRV_NAME "_panel %ux%u@%u %ubpp dsi %udl - ready",
+ default_mode.hdisplay, default_mode.vdisplay,
+ default_mode.vrefresh,
+ mipi_dsi_pixel_format_to_bpp(dsi->format), dsi->lanes);
+
+ jh057n_debugfs_init(ctx);
+ return 0;
+}
+
+static void jh057n_shutdown(struct mipi_dsi_device *dsi)
+{
+ struct jh057n *ctx = mipi_dsi_get_drvdata(dsi);
+ int ret;
+
+ ret = jh057n_unprepare(&ctx->panel);
+ if (ret < 0)
+ DRM_DEV_ERROR(&dsi->dev, "Failed to unprepare panel: %d\n",
+ ret);
+
+ ret = jh057n_disable(&ctx->panel);
+ if (ret < 0)
+ DRM_DEV_ERROR(&dsi->dev, "Failed to disable panel: %d\n",
+ ret);
+}
+
+static int jh057n_remove(struct mipi_dsi_device *dsi)
+{
+ struct jh057n *ctx = mipi_dsi_get_drvdata(dsi);
+ int ret;
+
+ jh057n_shutdown(dsi);
+
+ ret = mipi_dsi_detach(dsi);
+ if (ret < 0)
+ DRM_DEV_ERROR(&dsi->dev, "Failed to detach from DSI host: %d\n",
+ ret);
+
+ drm_panel_remove(&ctx->panel);
+
+ jh057n_debugfs_remove(ctx);
+
+ return 0;
+}
+
+static const struct of_device_id jh057n_of_match[] = {
+ { .compatible = "rocktech,jh057n00900" },
+ { /* Sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, jh057n_of_match);
+
+static struct mipi_dsi_driver jh057n_driver = {
+ .probe = jh057n_probe,
+ .remove = jh057n_remove,
+ .shutdown = jh057n_shutdown,
+ .driver = {
+ .name = DRV_NAME "_panel",
+ .of_match_table = jh057n_of_match,
+ },
+};
+module_mipi_dsi_driver(jh057n_driver);
+
+MODULE_AUTHOR("Guido Günther <[email protected]>");
+MODULE_DESCRIPTION("DRM driver for Rocktech JH057N00900 MIPI DSI panel");
+MODULE_LICENSE("GPL v2");
--
2.20.1
Add ROCKTECH DISPLAYS LIMITED (https://rocktech.com.hk) LCD panel
supplier.
Signed-off-by: Guido Günther <[email protected]>
---
Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 413c6f30ce88..cc24619a4249 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -338,6 +338,7 @@ ricoh Ricoh Co. Ltd.
rikomagic Rikomagic Tech Corp. Ltd
riscv RISC-V Foundation
rockchip Fuzhou Rockchip Electronics Co., Ltd
+rocktech ROCKTECH DISPLAYS LIMITED
rohm ROHM Semiconductor Co., Ltd
roofull Shenzhen Roofull Technology Co, Ltd
samsung Samsung Semiconductor
--
2.20.1
Hi Guido.
Thanks for addressing review comments in first round.
Just a few nits in this follow-up.
With these nits addressed:
Reviewed-by: Sam Ravnborg <[email protected]>
On Fri, Mar 01, 2019 at 02:02:04PM +0100, Guido G?nther wrote:
> +#include <video/display_timing.h>
This include file is, as far as I could tell, no longer used and can be dropped.
> +
> +static int jh057n_get_modes(struct drm_panel *panel)
> +{
> + struct drm_display_mode *mode;
> +
> + mode = drm_mode_duplicate(panel->drm, &default_mode);
> + if (!mode) {
> + DRM_ERROR("Failed to add mode %ux%u@%u",
> + default_mode.hdisplay, default_mode.vdisplay,
> + default_mode.vrefresh);
> + return -ENOMEM;
Use DRM_DEV_ERROR()
You can find dev via: panel->base.drm-dev
> +
> +static int jh057n_probe(struct mipi_dsi_device *dsi)
> +{
> + struct device *dev = &dsi->dev;
> + struct jh057n *ctx;
> + int ret;
> +
> + ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
> + if (!ctx)
> + return -ENOMEM;
> +
> + ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
> + if (IS_ERR(ctx->reset_gpio)) {
> + DRM_DEV_ERROR(dev, "cannot get reset gpio");
> + return PTR_ERR(ctx->reset_gpio);
> + }
> +
> + mipi_dsi_set_drvdata(dsi, ctx);
> +
> + ctx->dev = dev;
> +
> + dsi->lanes = 4;
> + dsi->format = MIPI_DSI_FMT_RGB888;
> + dsi->mode_flags = MIPI_DSI_MODE_VIDEO |
> + MIPI_DSI_MODE_VIDEO_BURST | MIPI_DSI_MODE_VIDEO_SYNC_PULSE;
> +
> + ctx->backlight = devm_of_find_backlight(dev);
> + if (IS_ERR(ctx->backlight))
> + return PTR_ERR(ctx->backlight);
> +
> + drm_panel_init(&ctx->panel);
> + ctx->panel.dev = dev;
> + ctx->panel.funcs = &jh057n_drm_funcs;
> +
> + drm_panel_add(&ctx->panel);
> +
> + ret = mipi_dsi_attach(dsi);
> + if (ret < 0) {
> + DRM_DEV_ERROR(dev, "mipi_dsi_attach failed. Is host ready?");
> + drm_panel_remove(&ctx->panel);
> + return ret;
> + }
> +
> + DRM_INFO(DRV_NAME "_panel %ux%u@%u %ubpp dsi %udl - ready",
> + default_mode.hdisplay, default_mode.vdisplay,
> + default_mode.vrefresh,
> + mipi_dsi_pixel_format_to_bpp(dsi->format), dsi->lanes);
You already have dev, so use DRM_DEV_INFO() and drop DRV_NAME
> +
> +static const struct of_device_id jh057n_of_match[] = {
> + { .compatible = "rocktech,jh057n00900" },
> + { /* Sentinel */ }
Lower case 's' (sorry, likely my bad)
> + .probe = jh057n_probe,
> + .remove = jh057n_remove,
> + .shutdown = jh057n_shutdown,
> + .driver = {
> + .name = DRV_NAME "_panel",
Drop "_panel" postfix. Other drivers do not use it.
Sam
Hi,
On Fri, Mar 01, 2019 at 11:39:06PM +0100, Sam Ravnborg wrote:
> Hi Guido.
>
> Thanks for addressing review comments in first round.
> Just a few nits in this follow-up.
> With these nits addressed:
> Reviewed-by: Sam Ravnborg <[email protected]>
Thanks! I made all the suggested changes in v3, on top of that I
prepended 'panel-rockteck-' to the driver name to be more consistent
with other drivers.
-- Guido
>
> On Fri, Mar 01, 2019 at 02:02:04PM +0100, Guido G?nther wrote:
>
> > +#include <video/display_timing.h>
> This include file is, as far as I could tell, no longer used and can be dropped.
>
> > +
> > +static int jh057n_get_modes(struct drm_panel *panel)
> > +{
> > + struct drm_display_mode *mode;
> > +
> > + mode = drm_mode_duplicate(panel->drm, &default_mode);
> > + if (!mode) {
> > + DRM_ERROR("Failed to add mode %ux%u@%u",
> > + default_mode.hdisplay, default_mode.vdisplay,
> > + default_mode.vrefresh);
> > + return -ENOMEM;
> Use DRM_DEV_ERROR()
> You can find dev via: panel->base.drm-dev
>
> > +
> > +static int jh057n_probe(struct mipi_dsi_device *dsi)
> > +{
> > + struct device *dev = &dsi->dev;
> > + struct jh057n *ctx;
> > + int ret;
> > +
> > + ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
> > + if (!ctx)
> > + return -ENOMEM;
> > +
> > + ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
> > + if (IS_ERR(ctx->reset_gpio)) {
> > + DRM_DEV_ERROR(dev, "cannot get reset gpio");
> > + return PTR_ERR(ctx->reset_gpio);
> > + }
> > +
> > + mipi_dsi_set_drvdata(dsi, ctx);
> > +
> > + ctx->dev = dev;
> > +
> > + dsi->lanes = 4;
> > + dsi->format = MIPI_DSI_FMT_RGB888;
> > + dsi->mode_flags = MIPI_DSI_MODE_VIDEO |
> > + MIPI_DSI_MODE_VIDEO_BURST | MIPI_DSI_MODE_VIDEO_SYNC_PULSE;
> > +
> > + ctx->backlight = devm_of_find_backlight(dev);
> > + if (IS_ERR(ctx->backlight))
> > + return PTR_ERR(ctx->backlight);
> > +
> > + drm_panel_init(&ctx->panel);
> > + ctx->panel.dev = dev;
> > + ctx->panel.funcs = &jh057n_drm_funcs;
> > +
> > + drm_panel_add(&ctx->panel);
> > +
> > + ret = mipi_dsi_attach(dsi);
> > + if (ret < 0) {
> > + DRM_DEV_ERROR(dev, "mipi_dsi_attach failed. Is host ready?");
> > + drm_panel_remove(&ctx->panel);
> > + return ret;
> > + }
> > +
> > + DRM_INFO(DRV_NAME "_panel %ux%u@%u %ubpp dsi %udl - ready",
> > + default_mode.hdisplay, default_mode.vdisplay,
> > + default_mode.vrefresh,
> > + mipi_dsi_pixel_format_to_bpp(dsi->format), dsi->lanes);
>
> You already have dev, so use DRM_DEV_INFO() and drop DRV_NAME
>
> > +
> > +static const struct of_device_id jh057n_of_match[] = {
> > + { .compatible = "rocktech,jh057n00900" },
> > + { /* Sentinel */ }
> Lower case 's' (sorry, likely my bad)
>
> > + .probe = jh057n_probe,
> > + .remove = jh057n_remove,
> > + .shutdown = jh057n_shutdown,
> > + .driver = {
> > + .name = DRV_NAME "_panel",
> Drop "_panel" postfix. Other drivers do not use it.
>
> Sam
>