This patchset adds nodes for Video Display support.
Dependencies :
- patch 1: VPU, HDMI & Power Controller bindings to be applied
- patch 2: Depends on AO-CEC-B bindings to be applied
- patch 3, 4, 5: Patch 1
Changes since v1:
- Added support for AO-CEC-B, enabling AO-CEC-B and disabling AO-CEC-A by default
[1] https://lkml.kernel.org/r/[email protected]
Neil Armstrong (5):
arm64: dts: meson-g12a: Add VPU and HDMI related nodes
arm64: dts: meson-g12a: Add AO-CEC nodes
arm64: dts: meson-g12a-x96-max: Add support for Video Display
arm64: dts: meson-g12a-sei510: Add support for Video Display
arm64: dts: meson-g12a-u200: Add support for Video Display
.../boot/dts/amlogic/meson-g12a-sei510.dts | 53 ++++++
.../boot/dts/amlogic/meson-g12a-u200.dts | 54 ++++++
.../boot/dts/amlogic/meson-g12a-x96-max.dts | 54 ++++++
arch/arm64/boot/dts/amlogic/meson-g12a.dtsi | 165 ++++++++++++++++++
4 files changed, 326 insertions(+)
--
2.21.0
Amlogic G12A embeds 2 CEC controllers :
- AO-CEC-A the same controller as in GXBB, GXL & GXM SoCs
- AO-CEC-B is a new controller
Note, the two controller can work simultanously since 2 Pads can
handle CEC, thus this SoC can handle 2 distinct CEC busses.
This patch adds the nodes for the AO-CEC-A and AO-CEC-B controllers.
Signed-off-by: Neil Armstrong <[email protected]>
---
arch/arm64/boot/dts/amlogic/meson-g12a.dtsi | 34 +++++++++++++++++++++
1 file changed, 34 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
index a696612f8f44..9f72396ba710 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
@@ -169,6 +169,22 @@
gpio-ranges = <&periphs_pinctrl 0 0 86>;
};
+ cec_ao_a_h_pins: cec_ao_a_h {
+ mux {
+ groups = "cec_ao_a_h";
+ function = "cec_ao_a_h";
+ bias-disable;
+ };
+ };
+
+ cec_ao_b_h_pins: cec_ao_b_h {
+ mux {
+ groups = "cec_ao_b_h";
+ function = "cec_ao_b_h";
+ bias-disable;
+ };
+ };
+
hdmitx_ddc_pins: hdmitx_ddc {
mux {
groups = "hdmitx_sda",
@@ -405,12 +421,30 @@
};
};
+ cec_AO: cec@100 {
+ compatible = "amlogic,meson-gx-ao-cec";
+ reg = <0x0 0x00100 0x0 0x14>;
+ interrupts = <GIC_SPI 199 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_AO CLKID_AO_CEC>;
+ clock-names = "core";
+ status = "disabled";
+ };
+
sec_AO: ao-secure@140 {
compatible = "amlogic,meson-gx-ao-secure", "syscon";
reg = <0x0 0x140 0x0 0x140>;
amlogic,has-chip-id;
};
+ cecb_AO: cec@280 {
+ compatible = "amlogic,meson-g12a-ao-cec";
+ reg = <0x0 0x00280 0x0 0x1c>;
+ interrupts = <GIC_SPI 203 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc_AO CLKID_AO_CTS_OSCIN>;
+ clock-names = "oscin";
+ status = "disabled";
+ };
+
uart_AO: serial@3000 {
compatible = "amlogic,meson-gx-uart",
"amlogic,meson-ao-uart";
--
2.21.0
This patch adds the HDMI, CVBS and CEC attributes and nodes to support
full display on the X96 Max STB.
AO-CEC-B is used by default and AO-CEC-A is disabled.
Signed-off-by: Neil Armstrong <[email protected]>
---
.../boot/dts/amlogic/meson-g12a-x96-max.dts | 54 +++++++++++++++++++
1 file changed, 54 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts
index b5b88262c06a..b3d913f28f12 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts
@@ -24,6 +24,27 @@
reg = <0x0 0x0 0x0 0x40000000>;
};
+ cvbs-connector {
+ compatible = "composite-video-connector";
+
+ port {
+ cvbs_connector_in: endpoint {
+ remote-endpoint = <&cvbs_vdac_out>;
+ };
+ };
+ };
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&hdmi_tx_tmds_out>;
+ };
+ };
+ };
+
flash_1v8: regulator-flash_1v8 {
compatible = "regulator-fixed";
regulator-name = "FLASH_1V8";
@@ -90,6 +111,39 @@
};
};
+&cec_AO {
+ pinctrl-0 = <&cec_ao_a_h_pins>;
+ pinctrl-names = "default";
+ status = "disabled";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
+&cecb_AO {
+ pinctrl-0 = <&cec_ao_b_h_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
+&cvbs_vdac_port {
+ cvbs_vdac_out: endpoint {
+ remote-endpoint = <&cvbs_connector_in>;
+ };
+};
+
+&hdmi_tx {
+ status = "okay";
+ pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+ pinctrl-names = "default";
+ hdmi-supply = <&vcc_5v>;
+};
+
+&hdmi_tx_tmds_port {
+ hdmi_tx_tmds_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+};
+
&uart_A {
status = "okay";
pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
--
2.21.0
This patch adds the HDMI, CVBS and CEC attributes and nodes to support
full display on the U200 Reference Design.
AO-CEC-B is used by default and AO-CEC-A is disabled.
Signed-off-by: Neil Armstrong <[email protected]>
---
.../boot/dts/amlogic/meson-g12a-u200.dts | 54 +++++++++++++++++++
1 file changed, 54 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts
index 2240e365af27..0e8045b8a915 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts
@@ -24,6 +24,16 @@
reg = <0x0 0x0 0x0 0x40000000>;
};
+ cvbs-connector {
+ compatible = "composite-video-connector";
+
+ port {
+ cvbs_connector_in: endpoint {
+ remote-endpoint = <&cvbs_vdac_out>;
+ };
+ };
+ };
+
flash_1v8: regulator-flash_1v8 {
compatible = "regulator-fixed";
regulator-name = "FLASH_1V8";
@@ -33,6 +43,17 @@
regulator-always-on;
};
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&hdmi_tx_tmds_out>;
+ };
+ };
+ };
+
main_12v: regulator-main_12v {
compatible = "regulator-fixed";
regulator-name = "12V";
@@ -102,6 +123,39 @@
};
+&cec_AO {
+ pinctrl-0 = <&cec_ao_a_h_pins>;
+ pinctrl-names = "default";
+ status = "disabled";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
+&cecb_AO {
+ pinctrl-0 = <&cec_ao_b_h_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
+&cvbs_vdac_port {
+ cvbs_vdac_out: endpoint {
+ remote-endpoint = <&cvbs_connector_in>;
+ };
+};
+
+&hdmi_tx {
+ status = "okay";
+ pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+ pinctrl-names = "default";
+ hdmi-supply = <&vcc_5v>;
+};
+
+&hdmi_tx_tmds_port {
+ hdmi_tx_tmds_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+};
+
&uart_AO {
status = "okay";
pinctrl-0 = <&uart_ao_a_pins>;
--
2.21.0
Add VPU and HDMI display support.
Signed-off-by: Neil Armstrong <[email protected]>
---
arch/arm64/boot/dts/amlogic/meson-g12a.dtsi | 131 ++++++++++++++++++++
1 file changed, 131 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
index 858ddd68665c..a696612f8f44 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
@@ -109,6 +109,37 @@
#size-cells = <2>;
ranges = <0x0 0x0 0x0 0xff600000 0x0 0x200000>;
+ hdmi_tx: hdmi-tx@0 {
+ compatible = "amlogic,meson-g12a-dw-hdmi";
+ reg = <0x0 0x0 0x0 0x10000>;
+ interrupts = <GIC_SPI 57 IRQ_TYPE_EDGE_RISING>;
+ resets = <&reset RESET_HDMITX_CAPB3>,
+ <&reset RESET_HDMITX_PHY>,
+ <&reset RESET_HDMITX>;
+ reset-names = "hdmitx_apb", "hdmitx", "hdmitx_phy";
+ clocks = <&clkc CLKID_HDMI>,
+ <&clkc CLKID_HTX_PCLK>,
+ <&clkc CLKID_VPU_INTR>;
+ clock-names = "isfr", "iahb", "venci";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+
+ /* VPU VENC Input */
+ hdmi_tx_venc_port: port@0 {
+ reg = <0>;
+
+ hdmi_tx_in: endpoint {
+ remote-endpoint = <&hdmi_tx_out>;
+ };
+ };
+
+ /* TMDS Output */
+ hdmi_tx_tmds_port: port@1 {
+ reg = <1>;
+ };
+ };
+
periphs: bus@34400 {
compatible = "simple-bus";
reg = <0x0 0x34400 0x0 0x400>;
@@ -138,6 +169,23 @@
gpio-ranges = <&periphs_pinctrl 0 0 86>;
};
+ hdmitx_ddc_pins: hdmitx_ddc {
+ mux {
+ groups = "hdmitx_sda",
+ "hdmitx_sck";
+ function = "hdmitx";
+ bias-disable;
+ };
+ };
+
+ hdmitx_hpd_pins: hdmitx_hpd {
+ mux {
+ groups = "hdmitx_hpd_in";
+ function = "hdmitx";
+ bias-disable;
+ };
+ };
+
uart_a_pins: uart-a {
mux {
groups = "uart_a_tx",
@@ -195,6 +243,19 @@
#phy-cells = <0>;
};
+ dmc: bus@38000 {
+ compatible = "simple-bus";
+ reg = <0x0 0x38000 0x0 0x400>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0x38000 0x0 0x400>;
+
+ canvas: video-lut@48 {
+ compatible = "amlogic,canvas";
+ reg = <0x0 0x48 0x0 0x14>;
+ };
+ };
+
usb2_phy1: phy@3a000 {
compatible = "amlogic,g12a-usb2-phy";
reg = <0x0 0x3a000 0x0 0x2000>;
@@ -262,6 +323,50 @@
clock-names = "xtal", "mpeg-clk";
};
+ pwrc_vpu: power-controller-vpu {
+ compatible = "amlogic,meson-g12a-pwrc-vpu";
+ #power-domain-cells = <0>;
+ amlogic,hhi-sysctrl = <&hhi>;
+ resets = <&reset RESET_VIU>,
+ <&reset RESET_VENC>,
+ <&reset RESET_VCBUS>,
+ <&reset RESET_BT656>,
+ <&reset RESET_RDMA>,
+ <&reset RESET_VENCI>,
+ <&reset RESET_VENCP>,
+ <&reset RESET_VDAC>,
+ <&reset RESET_VDI6>,
+ <&reset RESET_VENCL>,
+ <&reset RESET_VID_LOCK>;
+ clocks = <&clkc CLKID_VPU>,
+ <&clkc CLKID_VAPB>;
+ clock-names = "vpu", "vapb";
+ /*
+ * VPU clocking is provided by two identical clock paths
+ * VPU_0 and VPU_1 muxed to a single clock by a glitch
+ * free mux to safely change frequency while running.
+ * Same for VAPB but with a final gate after the glitch free mux.
+ */
+ assigned-clocks = <&clkc CLKID_VPU_0_SEL>,
+ <&clkc CLKID_VPU_0>,
+ <&clkc CLKID_VPU>, /* Glitch free mux */
+ <&clkc CLKID_VAPB_0_SEL>,
+ <&clkc CLKID_VAPB_0>,
+ <&clkc CLKID_VAPB_SEL>; /* Glitch free mux */
+ assigned-clock-parents = <&clkc CLKID_FCLK_DIV3>,
+ <0>, /* Do Nothing */
+ <&clkc CLKID_VPU_0>,
+ <&clkc CLKID_FCLK_DIV4>,
+ <0>, /* Do Nothing */
+ <&clkc CLKID_VAPB_0>;
+ assigned-clock-rates = <0>, /* Do Nothing */
+ <666666666>,
+ <0>, /* Do Nothing */
+ <0>, /* Do Nothing */
+ <250000000>,
+ <0>; /* Do Nothing */
+ };
+
ao_pinctrl: pinctrl@14 {
compatible = "amlogic,meson-g12a-aobus-pinctrl";
#address-cells = <2>;
@@ -341,6 +446,32 @@
};
};
+ vpu: vpu@ff900000 {
+ compatible = "amlogic,meson-g12a-vpu";
+ reg = <0x0 0xff900000 0x0 0x100000>,
+ <0x0 0xff63c000 0x0 0x1000>;
+ reg-names = "vpu", "hhi";
+ interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ amlogic,canvas = <&canvas>;
+ power-domains = <&pwrc_vpu>;
+
+ /* CVBS VDAC output port */
+ cvbs_vdac_port: port@0 {
+ reg = <0>;
+ };
+
+ /* HDMI-TX output port */
+ hdmi_tx_port: port@1 {
+ reg = <1>;
+
+ hdmi_tx_out: endpoint {
+ remote-endpoint = <&hdmi_tx_in>;
+ };
+ };
+ };
+
gic: interrupt-controller@ffc01000 {
compatible = "arm,gic-400";
reg = <0x0 0xffc01000 0 0x1000>,
--
2.21.0
This patch adds the HDMI, CVBS and CEC attributes and nodes to support
full display on the SEI510 STB.
AO-CEC-B is used by default and AO-CEC-A is disabled.
Signed-off-by: Neil Armstrong <[email protected]>
---
.../boot/dts/amlogic/meson-g12a-sei510.dts | 53 +++++++++++++++++++
1 file changed, 53 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts
index c350a0165d44..34b40587e5ef 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts
@@ -44,6 +44,16 @@
stdout-path = "serial0:115200n8";
};
+ cvbs-connector {
+ compatible = "composite-video-connector";
+
+ port {
+ cvbs_connector_in: endpoint {
+ remote-endpoint = <&cvbs_vdac_out>;
+ };
+ };
+ };
+
dc_in: regulator-dc_in {
compatible = "regulator-fixed";
regulator-name = "DC_IN";
@@ -61,6 +71,17 @@
regulator-always-on;
};
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&hdmi_tx_tmds_out>;
+ };
+ };
+ };
+
memory@0 {
device_type = "memory";
reg = <0x0 0x0 0x0 0x40000000>;
@@ -103,6 +124,26 @@
};
};
+&cec_AO {
+ pinctrl-0 = <&cec_ao_a_h_pins>;
+ pinctrl-names = "default";
+ status = "disabled";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
+&cecb_AO {
+ pinctrl-0 = <&cec_ao_b_h_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
+&cvbs_vdac_port {
+ cvbs_vdac_out: endpoint {
+ remote-endpoint = <&cvbs_connector_in>;
+ };
+};
+
&saradc {
status = "okay";
vref-supply = <&vddio_ao1v8>;
@@ -120,6 +161,18 @@
};
};
+&hdmi_tx {
+ status = "okay";
+ pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+ pinctrl-names = "default";
+};
+
+&hdmi_tx_tmds_port {
+ hdmi_tx_tmds_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+};
+
&uart_AO {
status = "okay";
pinctrl-0 = <&uart_ao_a_pins>;
--
2.21.0
Neil Armstrong <[email protected]> writes:
> This patchset adds nodes for Video Display support.
>
> Dependencies :
> - patch 1: VPU, HDMI & Power Controller bindings to be applied
These are applied.
> - patch 2: Depends on AO-CEC-B bindings to be applied
These are reviewed/acked and don't cause build/boot problems.
> - patch 3, 4, 5: Patch 1
Since all the deps are ready, queuing this for v5.2,
Kevin