Raspberry Pi's firmware offers and interface though which update it's
performance requirements. It allows us to request for specific runtime
frequencies, which the firmware might or might not respect, depending on
the firmware configuration and thermals.
As the maximum and minimum frequencies are configurable in the firmware
there is no way to know in advance their values. So the Raspberry Pi
cpufreq driver queries them, builds an opp frequency table to then
launch cpufreq-dt.
Signed-off-by: Nicolas Saenz Julienne <[email protected]>
---
drivers/cpufreq/Kconfig.arm | 8 +++
drivers/cpufreq/Makefile | 1 +
drivers/cpufreq/raspberrypi-cpufreq.c | 83 +++++++++++++++++++++++++++
3 files changed, 92 insertions(+)
create mode 100644 drivers/cpufreq/raspberrypi-cpufreq.c
diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
index 179a1d302f48..f6eba7ae50d0 100644
--- a/drivers/cpufreq/Kconfig.arm
+++ b/drivers/cpufreq/Kconfig.arm
@@ -308,3 +308,11 @@ config ARM_PXA2xx_CPUFREQ
This add the CPUFreq driver support for Intel PXA2xx SOCs.
If in doubt, say N.
+
+config ARM_RASPBERRYPI_CPUFREQ
+ tristate "Raspberry Pi cpufreq support"
+ depends on RASPBERRYPI_FIRMWARE || COMPILE_TEST
+ help
+ This adds the CPUFreq driver for Raspberry Pi
+
+ If in doubt, say N.
diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile
index 689b26c6f949..02678e9b2ff5 100644
--- a/drivers/cpufreq/Makefile
+++ b/drivers/cpufreq/Makefile
@@ -84,6 +84,7 @@ obj-$(CONFIG_ARM_TEGRA124_CPUFREQ) += tegra124-cpufreq.o
obj-$(CONFIG_ARM_TEGRA186_CPUFREQ) += tegra186-cpufreq.o
obj-$(CONFIG_ARM_TI_CPUFREQ) += ti-cpufreq.o
obj-$(CONFIG_ARM_VEXPRESS_SPC_CPUFREQ) += vexpress-spc-cpufreq.o
+obj-$(CONFIG_ARM_RASPBERRYPI_CPUFREQ) += raspberrypi-cpufreq.o
##################################################################################
diff --git a/drivers/cpufreq/raspberrypi-cpufreq.c b/drivers/cpufreq/raspberrypi-cpufreq.c
new file mode 100644
index 000000000000..a85988867d56
--- /dev/null
+++ b/drivers/cpufreq/raspberrypi-cpufreq.c
@@ -0,0 +1,83 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Raspberry Pi cpufreq driver
+ *
+ * Copyright (C) 2019, Nicolas Saenz Julienne <[email protected]>
+ */
+
+#include <linux/of.h>
+#include <linux/clk.h>
+#include <linux/cpu.h>
+#include <linux/module.h>
+#include <linux/pm_opp.h>
+#include <linux/cpufreq.h>
+#include <linux/platform_device.h>
+
+static const struct of_device_id machines[] __initconst = {
+ { .compatible = "raspberrypi,3-model-b-plus" },
+ { .compatible = "raspberrypi,3-model-b" },
+ { /* sentinel */ }
+};
+
+static int __init raspberrypi_cpufreq_driver_init(void)
+{
+ struct platform_device *pdev;
+ struct device *cpu_dev;
+ struct clk *clk;
+ long min, max;
+ long rate;
+ int ret;
+
+ if (!of_match_node(machines, of_root))
+ return -ENODEV;
+
+ cpu_dev = get_cpu_device(0);
+ if (!cpu_dev) {
+ pr_err("Cannot get CPU for cpufreq driver\n");
+ return -ENODEV;
+ }
+
+ clk = clk_get(cpu_dev, 0);
+ if (IS_ERR(clk)) {
+ dev_err(cpu_dev, "Cannot get clock for CPU0\n");
+ return PTR_ERR(clk);
+ }
+
+ /*
+ * The max and min frequencies are configurable in the Raspberry Pi
+ * firmware, so we query them at runtime
+ */
+ min = clk_round_rate(clk, 0);
+ max = clk_round_rate(clk, ULONG_MAX);
+ clk_put(clk);
+
+ for (rate = min; rate < max; rate += 100000000) {
+ ret = dev_pm_opp_add(cpu_dev, rate, 0);
+ if (ret)
+ goto remove_opp;
+ }
+
+ ret = dev_pm_opp_add(cpu_dev, max, 0);
+ if (ret)
+ goto remove_opp;
+
+ pdev = platform_device_register_data(NULL, "cpufreq-dt", -1, NULL, 0);
+ ret = PTR_ERR_OR_ZERO(pdev);
+ if (ret) {
+ dev_err(cpu_dev, "Failed to create platform device, %d\n", ret);
+ goto remove_opp;
+ }
+
+ return 0;
+
+remove_opp:
+ dev_pm_opp_remove_all_dynamic(cpu_dev);
+
+ return ret;
+}
+
+late_initcall(raspberrypi_cpufreq_driver_init);
+
+MODULE_AUTHOR("Nicolas Saenz Julienne <[email protected]");
+MODULE_DESCRIPTION("Raspberry Pi cpufreq driver");
+MODULE_LICENSE("GPL v2");
--
2.21.0
On 20-05-19, 12:47, Nicolas Saenz Julienne wrote:
> Raspberry Pi's firmware offers and interface though which update it's
> performance requirements. It allows us to request for specific runtime
> frequencies, which the firmware might or might not respect, depending on
> the firmware configuration and thermals.
>
> As the maximum and minimum frequencies are configurable in the firmware
> there is no way to know in advance their values. So the Raspberry Pi
> cpufreq driver queries them, builds an opp frequency table to then
> launch cpufreq-dt.
>
> Signed-off-by: Nicolas Saenz Julienne <[email protected]>
> ---
> drivers/cpufreq/Kconfig.arm | 8 +++
> drivers/cpufreq/Makefile | 1 +
> drivers/cpufreq/raspberrypi-cpufreq.c | 83 +++++++++++++++++++++++++++
> 3 files changed, 92 insertions(+)
> create mode 100644 drivers/cpufreq/raspberrypi-cpufreq.c
>
> diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
> index 179a1d302f48..f6eba7ae50d0 100644
> --- a/drivers/cpufreq/Kconfig.arm
> +++ b/drivers/cpufreq/Kconfig.arm
> @@ -308,3 +308,11 @@ config ARM_PXA2xx_CPUFREQ
> This add the CPUFreq driver support for Intel PXA2xx SOCs.
>
> If in doubt, say N.
> +
> +config ARM_RASPBERRYPI_CPUFREQ
> + tristate "Raspberry Pi cpufreq support"
> + depends on RASPBERRYPI_FIRMWARE || COMPILE_TEST
> + help
> + This adds the CPUFreq driver for Raspberry Pi
> +
> + If in doubt, say N.
> diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile
> index 689b26c6f949..02678e9b2ff5 100644
> --- a/drivers/cpufreq/Makefile
> +++ b/drivers/cpufreq/Makefile
> @@ -84,6 +84,7 @@ obj-$(CONFIG_ARM_TEGRA124_CPUFREQ) += tegra124-cpufreq.o
> obj-$(CONFIG_ARM_TEGRA186_CPUFREQ) += tegra186-cpufreq.o
> obj-$(CONFIG_ARM_TI_CPUFREQ) += ti-cpufreq.o
> obj-$(CONFIG_ARM_VEXPRESS_SPC_CPUFREQ) += vexpress-spc-cpufreq.o
> +obj-$(CONFIG_ARM_RASPBERRYPI_CPUFREQ) += raspberrypi-cpufreq.o
My bad sorry, I noticed this earlier and forgot to comment. The above
two files are maintained in alphabetical order, please add the entries
at relevant places.
> ##################################################################################
> diff --git a/drivers/cpufreq/raspberrypi-cpufreq.c b/drivers/cpufreq/raspberrypi-cpufreq.c
> new file mode 100644
> index 000000000000..a85988867d56
> --- /dev/null
> +++ b/drivers/cpufreq/raspberrypi-cpufreq.c
> @@ -0,0 +1,83 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Raspberry Pi cpufreq driver
> + *
> + * Copyright (C) 2019, Nicolas Saenz Julienne <[email protected]>
> + */
> +
> +#include <linux/of.h>
> +#include <linux/clk.h>
> +#include <linux/cpu.h>
> +#include <linux/module.h>
> +#include <linux/pm_opp.h>
> +#include <linux/cpufreq.h>
> +#include <linux/platform_device.h>
Would be better to keep above in alphabetical order as well.
Please don't send another version now and wait for comments on the
other patches.
--
viresh
On 20.05.19 12:47, Nicolas Saenz Julienne wrote:
> Raspberry Pi's firmware offers and interface though which update it's
> performance requirements. It allows us to request for specific runtime
> frequencies, which the firmware might or might not respect, depending on
> the firmware configuration and thermals.
>
> As the maximum and minimum frequencies are configurable in the firmware
> there is no way to know in advance their values. So the Raspberry Pi
> cpufreq driver queries them, builds an opp frequency table to then
> launch cpufreq-dt.
>
> Signed-off-by: Nicolas Saenz Julienne <[email protected]>
> ---
> drivers/cpufreq/Kconfig.arm | 8 +++
> drivers/cpufreq/Makefile | 1 +
> drivers/cpufreq/raspberrypi-cpufreq.c | 83 +++++++++++++++++++++++++++
> 3 files changed, 92 insertions(+)
> create mode 100644 drivers/cpufreq/raspberrypi-cpufreq.c
>
> diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
> index 179a1d302f48..f6eba7ae50d0 100644
> --- a/drivers/cpufreq/Kconfig.arm
> +++ b/drivers/cpufreq/Kconfig.arm
> @@ -308,3 +308,11 @@ config ARM_PXA2xx_CPUFREQ
> This add the CPUFreq driver support for Intel PXA2xx SOCs.
>
> If in doubt, say N.
> +
> +config ARM_RASPBERRYPI_CPUFREQ
> + tristate "Raspberry Pi cpufreq support"
> + depends on RASPBERRYPI_FIRMWARE || COMPILE_TEST
The driver doesn't really require the firmware driver to compile, how about:
select RASPBERRYPI_FIRMWARE
> + help
> + This adds the CPUFreq driver for Raspberry Pi
> +
> + If in doubt, say N.
> diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile
> index 689b26c6f949..02678e9b2ff5 100644
> --- a/drivers/cpufreq/Makefile
> +++ b/drivers/cpufreq/Makefile
> @@ -84,6 +84,7 @@ obj-$(CONFIG_ARM_TEGRA124_CPUFREQ) += tegra124-cpufreq.o
> obj-$(CONFIG_ARM_TEGRA186_CPUFREQ) += tegra186-cpufreq.o
> obj-$(CONFIG_ARM_TI_CPUFREQ) += ti-cpufreq.o
> obj-$(CONFIG_ARM_VEXPRESS_SPC_CPUFREQ) += vexpress-spc-cpufreq.o
> +obj-$(CONFIG_ARM_RASPBERRYPI_CPUFREQ) += raspberrypi-cpufreq.o
>
>
> ##################################################################################
> diff --git a/drivers/cpufreq/raspberrypi-cpufreq.c b/drivers/cpufreq/raspberrypi-cpufreq.c
> new file mode 100644
> index 000000000000..a85988867d56
> --- /dev/null
> +++ b/drivers/cpufreq/raspberrypi-cpufreq.c
> @@ -0,0 +1,83 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Raspberry Pi cpufreq driver
> + *
> + * Copyright (C) 2019, Nicolas Saenz Julienne <[email protected]>
> + */
> +
> +#include <linux/of.h>
> +#include <linux/clk.h>
> +#include <linux/cpu.h>
> +#include <linux/module.h>
> +#include <linux/pm_opp.h>
> +#include <linux/cpufreq.h>
> +#include <linux/platform_device.h>
> +
> +static const struct of_device_id machines[] __initconst = {
> + { .compatible = "raspberrypi,3-model-b-plus" },
> + { .compatible = "raspberrypi,3-model-b" },
> + { /* sentinel */ }
> +};
> +
> +static int __init raspberrypi_cpufreq_driver_init(void)
> +{
> + struct platform_device *pdev;
> + struct device *cpu_dev;
> + struct clk *clk;
> + long min, max;
> + long rate;
> + int ret;
> +
> + if (!of_match_node(machines, of_root))
> + return -ENODEV;
> +
> + cpu_dev = get_cpu_device(0);
> + if (!cpu_dev) {
> + pr_err("Cannot get CPU for cpufreq driver\n");
> + return -ENODEV;
> + }
> +
> + clk = clk_get(cpu_dev, 0);
I suggest use the expected clock ID.