From: Yegor Yefremov <[email protected]>
This patch permits the usage for GPIOs to control
the CTS/RTS/DTR/DSR/DCD/RI signals.
Changed by Stefan:
Only call mctrl_gpio_init(), if the device has no ACPI companion device
to not break existing ACPI based systems. Also only use the mctrl_gpio_
functions when "gpios" is available.
Signed-off-by: Yegor Yefremov <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
Cc: Mika Westerberg <[email protected]>
Cc: Andy Shevchenko <[email protected]>
Cc: Giulio Benetti <[email protected]>
Cc: Yegor Yefremov <[email protected]>
Cc: Greg Kroah-Hartman <[email protected]>
---
v3:
- Only call mctrl_gpio_init(), if the device has no ACPI companion device
to not break existing ACPI based systems, as suggested by Andy
v2:
- No change
Please note that this patch was already applied before [1]. And later
reverted [2] because it introduced problems on some x86 based boards
(ACPI GPIO related). Here a detailed description of the issue at that
time:
https://lkml.org/lkml/2016/8/9/357
http://www.spinics.net/lists/linux-serial/msg23071.html
This is a re-send of the original patch that was applied at that time.
With patch 1/2 from this series this issue should be fixed now (please
note that I can't test it on such an x86 platform causing these
problems).
Andy (or Mika), perhaps it would be possible for you to test this
patch again, now with patch 1/2 of this series applied as well?
That would be really helpful.
Thanks,
Stefan
[1] 4ef03d328769 ("tty/serial/8250: use mctrl_gpio helpers")
[2] 5db4f7f80d16 ("Revert "tty/serial/8250: use mctrl_gpio helpers"")
.../devicetree/bindings/serial/8250.txt | 19 +++++++++
drivers/tty/serial/8250/8250.h | 40 ++++++++++++++++++-
drivers/tty/serial/8250/8250_core.c | 17 ++++++++
drivers/tty/serial/8250/8250_omap.c | 31 ++++++++------
drivers/tty/serial/8250/8250_port.c | 9 +++++
drivers/tty/serial/8250/Kconfig | 1 +
include/linux/serial_8250.h | 1 +
7 files changed, 104 insertions(+), 14 deletions(-)
diff --git a/Documentation/devicetree/bindings/serial/8250.txt b/Documentation/devicetree/bindings/serial/8250.txt
index 3cba12f855b7..20d351f268ef 100644
--- a/Documentation/devicetree/bindings/serial/8250.txt
+++ b/Documentation/devicetree/bindings/serial/8250.txt
@@ -53,6 +53,9 @@ Optional properties:
programmable TX FIFO thresholds.
- resets : phandle + reset specifier pairs
- overrun-throttle-ms : how long to pause uart rx when input overrun is encountered.
+- {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD
+ line respectively. It will use specified GPIO instead of the peripheral
+ function pin for the UART feature. If unsure, don't specify this property.
Note:
* fsl,ns16550:
@@ -74,3 +77,19 @@ Example:
interrupts = <10>;
reg-shift = <2>;
};
+
+Example for OMAP UART using GPIO-based modem control signals:
+
+ uart4: serial@49042000 {
+ compatible = "ti,omap3-uart";
+ reg = <0x49042000 0x400>;
+ interrupts = <80>;
+ ti,hwmods = "uart4";
+ clock-frequency = <48000000>;
+ cts-gpios = <&gpio3 5 GPIO_ACTIVE_LOW>;
+ rts-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>;
+ dtr-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+ dsr-gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+ dcd-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+ rng-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ };
diff --git a/drivers/tty/serial/8250/8250.h b/drivers/tty/serial/8250/8250.h
index ebfb0bd5bef5..441aab94264b 100644
--- a/drivers/tty/serial/8250/8250.h
+++ b/drivers/tty/serial/8250/8250.h
@@ -11,6 +11,8 @@
#include <linux/serial_reg.h>
#include <linux/dmaengine.h>
+#include "../serial_mctrl_gpio.h"
+
struct uart_8250_dma {
int (*tx_dma)(struct uart_8250_port *p);
int (*rx_dma)(struct uart_8250_port *p);
@@ -142,11 +144,47 @@ void serial8250_em485_destroy(struct uart_8250_port *p);
static inline void serial8250_out_MCR(struct uart_8250_port *up, int value)
{
serial_out(up, UART_MCR, value);
+
+ if (up->gpios) {
+ int mctrl_gpio = 0;
+
+ if (value & UART_MCR_RTS)
+ mctrl_gpio |= TIOCM_RTS;
+ if (value & UART_MCR_DTR)
+ mctrl_gpio |= TIOCM_DTR;
+
+ mctrl_gpio_set(up->gpios, mctrl_gpio);
+ }
}
static inline int serial8250_in_MCR(struct uart_8250_port *up)
{
- return serial_in(up, UART_MCR);
+ int mctrl;
+
+ mctrl = serial_in(up, UART_MCR);
+
+ if (up->gpios) {
+ int mctrl_gpio = 0;
+
+ /* save current MCR values */
+ if (mctrl & UART_MCR_RTS)
+ mctrl_gpio |= TIOCM_RTS;
+ if (mctrl & UART_MCR_DTR)
+ mctrl_gpio |= TIOCM_DTR;
+
+ mctrl_gpio = mctrl_gpio_get_outputs(up->gpios, &mctrl_gpio);
+ if (mctrl_gpio & TIOCM_RTS)
+ mctrl |= UART_MCR_RTS;
+ else
+ mctrl &= ~UART_MCR_RTS;
+
+ if (mctrl_gpio & TIOCM_DTR)
+ mctrl |= UART_MCR_DTR;
+ else
+ mctrl &= ~UART_MCR_DTR;
+ }
+
+ return mctrl;
}
#if defined(__alpha__) && !defined(CONFIG_PCI)
diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c
index e441221e04b9..a4470771005f 100644
--- a/drivers/tty/serial/8250/8250_core.c
+++ b/drivers/tty/serial/8250/8250_core.c
@@ -14,6 +14,7 @@
* serial8250_register_8250_port() ports
*/
+#include <linux/acpi.h>
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/ioport.h>
@@ -982,6 +983,8 @@ int serial8250_register_8250_port(struct uart_8250_port *up)
uart = serial8250_find_match_or_unused(&up->port);
if (uart && uart->port.type != PORT_8250_CIR) {
+ struct mctrl_gpios *gpios;
+
if (uart->port.dev)
uart_remove_one_port(&serial8250_reg, &uart->port);
@@ -1016,6 +1019,20 @@ int serial8250_register_8250_port(struct uart_8250_port *up)
if (up->port.flags & UPF_FIXED_TYPE)
uart->port.type = up->port.type;
+ /*
+ * Only call mctrl_gpio_init(), if the device has no ACPI
+ * companion device
+ */
+ if (!has_acpi_companion(uart->port.dev)) {
+ gpios = mctrl_gpio_init(&uart->port, 0);
+ if (IS_ERR(gpios)) {
+ if (PTR_ERR(gpios) != -ENOSYS)
+ return PTR_ERR(gpios);
+ } else {
+ uart->gpios = gpios;
+ }
+ }
+
serial8250_set_defaults(uart);
/* Possibly override default I/O functions. */
diff --git a/drivers/tty/serial/8250/8250_omap.c b/drivers/tty/serial/8250/8250_omap.c
index 0a8316632d75..562ac73d9f2f 100644
--- a/drivers/tty/serial/8250/8250_omap.c
+++ b/drivers/tty/serial/8250/8250_omap.c
@@ -141,18 +141,21 @@ static void omap8250_set_mctrl(struct uart_port *port, unsigned int mctrl)
serial8250_do_set_mctrl(port, mctrl);
- /*
- * Turn off autoRTS if RTS is lowered and restore autoRTS setting
- * if RTS is raised
- */
- lcr = serial_in(up, UART_LCR);
- serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
- if ((mctrl & TIOCM_RTS) && (port->status & UPSTAT_AUTORTS))
- priv->efr |= UART_EFR_RTS;
- else
- priv->efr &= ~UART_EFR_RTS;
- serial_out(up, UART_EFR, priv->efr);
- serial_out(up, UART_LCR, lcr);
+ if (IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(up->gpios,
+ UART_GPIO_RTS))) {
+ /*
+ * Turn off autoRTS if RTS is lowered and restore autoRTS
+ * setting if RTS is raised
+ */
+ lcr = serial_in(up, UART_LCR);
+ serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
+ if ((mctrl & TIOCM_RTS) && (port->status & UPSTAT_AUTORTS))
+ priv->efr |= UART_EFR_RTS;
+ else
+ priv->efr &= ~UART_EFR_RTS;
+ serial_out(up, UART_EFR, priv->efr);
+ serial_out(up, UART_LCR, lcr);
+ }
}
/*
@@ -453,7 +456,9 @@ static void omap_8250_set_termios(struct uart_port *port,
priv->efr = 0;
up->port.status &= ~(UPSTAT_AUTOCTS | UPSTAT_AUTORTS | UPSTAT_AUTOXOFF);
- if (termios->c_cflag & CRTSCTS && up->port.flags & UPF_HARD_FLOW) {
+ if (termios->c_cflag & CRTSCTS && up->port.flags & UPF_HARD_FLOW
+ && IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(up->gpios,
+ UART_GPIO_RTS))) {
/* Enable AUTOCTS (autoRTS is enabled when RTS is raised) */
up->port.status |= UPSTAT_AUTOCTS | UPSTAT_AUTORTS;
priv->efr |= UART_EFR_CTS;
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index 2304a84eee3b..1925e62f05bf 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -1662,6 +1662,9 @@ static void serial8250_disable_ms(struct uart_port *port)
if (up->bugs & UART_BUG_NOMSR)
return;
+ if (up->gpios)
+ mctrl_gpio_disable_ms(up->gpios);
+
up->ier &= ~UART_IER_MSI;
serial_port_out(port, UART_IER, up->ier);
}
@@ -1674,6 +1677,9 @@ static void serial8250_enable_ms(struct uart_port *port)
if (up->bugs & UART_BUG_NOMSR)
return;
+ if (up->gpios)
+ mctrl_gpio_enable_ms(up->gpios);
+
up->ier |= UART_IER_MSI;
serial8250_rpm_get(up);
@@ -1951,6 +1957,9 @@ unsigned int serial8250_do_get_mctrl(struct uart_port *port)
serial8250_rpm_put(up);
ret = 0;
+ if (up->gpios)
+ return mctrl_gpio_get(up->gpios, &ret);
+
if (status & UART_MSR_DCD)
ret |= TIOCM_CAR;
if (status & UART_MSR_RI)
diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig
index 296115f6a4d8..509f6a3bb9ff 100644
--- a/drivers/tty/serial/8250/Kconfig
+++ b/drivers/tty/serial/8250/Kconfig
@@ -8,6 +8,7 @@ config SERIAL_8250
tristate "8250/16550 and compatible serial support"
depends on !S390
select SERIAL_CORE
+ select SERIAL_MCTRL_GPIO if GPIOLIB
---help---
This selects whether you want to include the driver for the standard
serial ports. The standard answer is Y. People who might say N
diff --git a/include/linux/serial_8250.h b/include/linux/serial_8250.h
index 5a655ba8d273..14cd763baf78 100644
--- a/include/linux/serial_8250.h
+++ b/include/linux/serial_8250.h
@@ -114,6 +114,7 @@ struct uart_8250_port {
* if no_console_suspend
*/
unsigned char probe;
+ struct mctrl_gpios *gpios;
#define UART_PROBE_RSA (1 << 0)
/*
--
2.21.0
On Mon, May 27, 2019 at 01:18:05PM +0200, Stefan Roese wrote:
> From: Yegor Yefremov <[email protected]>
>
> This patch permits the usage for GPIOs to control
> the CTS/RTS/DTR/DSR/DCD/RI signals.
>
> Changed by Stefan:
> Only call mctrl_gpio_init(), if the device has no ACPI companion device
> to not break existing ACPI based systems. Also only use the mctrl_gpio_
> functions when "gpios" is available.
>
> Signed-off-by: Yegor Yefremov <[email protected]>
> Signed-off-by: Greg Kroah-Hartman <[email protected]>
> Signed-off-by: Stefan Roese <[email protected]>
> Cc: Mika Westerberg <[email protected]>
> Cc: Andy Shevchenko <[email protected]>
> Cc: Giulio Benetti <[email protected]>
> Cc: Yegor Yefremov <[email protected]>
> Cc: Greg Kroah-Hartman <[email protected]>
> ---
> v3:
> - Only call mctrl_gpio_init(), if the device has no ACPI companion device
> to not break existing ACPI based systems, as suggested by Andy
>
> v2:
> - No change
>
> Please note that this patch was already applied before [1]. And later
> reverted [2] because it introduced problems on some x86 based boards
> (ACPI GPIO related). Here a detailed description of the issue at that
> time:
>
> https://lkml.org/lkml/2016/8/9/357
> http://www.spinics.net/lists/linux-serial/msg23071.html
>
> This is a re-send of the original patch that was applied at that time.
> With patch 1/2 from this series this issue should be fixed now (please
> note that I can't test it on such an x86 platform causing these
> problems).
>
> Andy (or Mika), perhaps it would be possible for you to test this
> patch again, now with patch 1/2 of this series applied as well?
> That would be really helpful.
Unfortunately I'm not able to test this anymore. Andy should be able to
test this but he is on vacation this week.
Regarding the ACPI changes in this patch, they look good to me so
Reviewed-by: Mika Westerberg <[email protected]>