The Librem5 devkit is based on the imx8mq from NXP. This is a default
devicetree to boot the board to a command prompt.
Changes since v15:
Update the ti,minimum-sys-voltage for the PMIC.
Changes since v14:
Add regulator-always-on for the SNVS regulators.
Added pgc nodes.
Fixed charger pre-current.
Changes since v13:
Moved haptic motor from pwm-led to gpio-vibrator.
Cleaned up regulator node naming.
Whitescpace cleanup.
Re-indent pinmux stanzas.
Drop pwm2 node.
Drop MAINTAINERS patch.
Changes since v12:
Updated patch to vendor-prefixes.yaml.
Dropped always on from regulators.
Changes since v11:
Added reviewed-by tags.
Fixed subject typo.
Changes since v10:
Moved MAINTAINERS entry to "ARM/FREESCALE IMX" section
Changes since v9:
Added a MAINTAINERS entry for arm64 imx devicetree files.
Changes since v8:
Fixed license comment.
Changed regulators to all lower case.
Changed clock frequency for NXP errata e7805.
Dropped blank line.
Changes since v7:
More regulators always on for USB.
Add vbus regulator.
Drop vbat regulator.
Replace legacy "gpio-key,wakeup" with "wakeup-source".
Add vbus-supply to get rid of warning
imx8mq-usb-phy 382f0040.usb-phy: 382f0040.usb-phy supply vbus not found,
using dummy regulator
Changes since v6:
Dropped unused regulators.
Fix regulator phandles case.
Dropped extra whitespace.
Changes since v5:
Added reviewed-by tags.
Moved USB port links to USB controller node.
Changes since v4:
Compiled against linux-next next-20190415.
Added imx8mq to the arm yaml file.
Re-arrange regulator nodes to drop undefined supplies.
Additional ordering for aesthetics.
Split some long lines.
Added lots of blank lines.
Moved pinctl muxes to where they are used.
Cleaned out reg defintions from regulator nodes.
Changes since v3:
Freshly sorted and pressed nodes.
Change the backlight to an interpolated scale.
Dropped i2c2.
Dropped devkit version number to match debian MR.
Changes since v2:
Fixed incorrect phy-supply for the fsl-fec.
Dropped unused regulator property.
Fixup Makefile for linux-next.
Changes since v1:
Dropped config file.
Updated the board compatible label.
Changed node names to follow naming conventions.
Added a more complete regulator hierachy.
Removed unused nodes.
Removed unknown devices.
Fixed comment style.
Dropped undocumented properties.
Angus Ainslie (Purism) (3):
arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit
dt-bindings: Add an entry for Purism SPC
dt-bindings: arm: fsl: Add the imx8mq boards
.../devicetree/bindings/arm/fsl.yaml | 7 +
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../dts/freescale/imx8mq-librem5-devkit.dts | 806 ++++++++++++++++++
4 files changed, 816 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
--
2.17.1
This is for the development kit board for the Librem 5. The current level
of support yields a working console and is able to boot userspace from
the network or eMMC.
Additional subsystems that are active :
- Both USB ports
- SD card socket
- WiFi usdhc
- WWAN modem
- GNSS
- GPIO keys
- LEDs
- gyro
- magnetometer
- touchscreen
- pwm
- backlight
- haptic motor
Signed-off-by: Angus Ainslie (Purism) <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
---
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../dts/freescale/imx8mq-librem5-devkit.dts | 806 ++++++++++++++++++
2 files changed, 807 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 0bd122f60549..c043aca66572 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -22,6 +22,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-rmb3.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-zest.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8qxp-mek.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
new file mode 100644
index 000000000000..93b3830e5406
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
@@ -0,0 +1,806 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2018-2019 Purism SPC
+ */
+
+/dts-v1/;
+
+#include "dt-bindings/input/input.h"
+#include "dt-bindings/pwm/pwm.h"
+#include "dt-bindings/usb/pd.h"
+#include "imx8mq.dtsi"
+
+/ {
+ model = "Purism Librem 5 devkit";
+ compatible = "purism,librem5-devkit", "fsl,imx8mq";
+
+ backlight_dsi: backlight-dsi {
+ compatible = "pwm-backlight";
+ /* 200 Hz for the PAM2841 */
+ pwms = <&pwm1 0 5000000>;
+ brightness-levels = <0 100>;
+ num-interpolated-steps = <100>;
+ /* Default brightness level (index into the array defined by */
+ /* the "brightness-levels" property) */
+ default-brightness-level = <0>;
+ power-supply = <®_22v4_p>;
+ };
+
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_keys>;
+
+ btn1 {
+ label = "VOL_UP";
+ gpios = <&gpio4 21 GPIO_ACTIVE_LOW>;
+ wakeup-source;
+ linux,code = <KEY_VOLUMEUP>;
+ };
+
+ btn2 {
+ label = "VOL_DOWN";
+ gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
+ wakeup-source;
+ linux,code = <KEY_VOLUMEDOWN>;
+ };
+
+ hp-det {
+ label = "HP_DET";
+ gpios = <&gpio3 20 GPIO_ACTIVE_LOW>;
+ wakeup-source;
+ linux,code = <KEY_HP>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_leds>;
+
+ led1 {
+ label = "LED 1";
+ gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ };
+
+ pmic_osc: clock-pmic {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-output-names = "pmic_osc";
+ };
+
+ reg_1v8_p: regulator-1v8-p {
+ compatible = "regulator-fixed";
+ regulator-name = "1v8_p";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <®_pwr_en>;
+ };
+
+ reg_2v8_p: regulator-2v8-p {
+ compatible = "regulator-fixed";
+ regulator-name = "2v8_p";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ vin-supply = <®_pwr_en>;
+ };
+
+ reg_3v3_p: regulator-3v3-p {
+ compatible = "regulator-fixed";
+ regulator-name = "3v3_p";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <®_pwr_en>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ reg_5v_p: regulator-5v-p {
+ compatible = "regulator-fixed";
+ regulator-name = "5v_p";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <®_pwr_en>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ reg_22v4_p: regulator-22v4-p {
+ compatible = "regulator-fixed";
+ regulator-name = "22v4_P";
+ regulator-min-microvolt = <22400000>;
+ regulator-max-microvolt = <22400000>;
+ vin-supply = <®_pwr_en>;
+ };
+
+ reg_pwr_en: regulator-pwr-en {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwr_en>;
+ regulator-name = "PWR_EN";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ reg_usdhc2_vmmc: regulator-usdhc2-vmmc {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2_pwr>;
+ regulator-name = "VSD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ vibrator {
+ compatible = "gpio-vibrator";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_haptic>;
+ enable-gpios = <&gpio5 4 GPIO_ACTIVE_LOW>;
+ vcc-supply = <®_3v3_p>;
+ };
+
+ wifi_pwr_en: regulator-wifi-en {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wifi_pwr_en>;
+ regulator-name = "WIFI_EN";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+};
+
+&clk {
+ assigned-clocks = <&clk IMX8MQ_AUDIO_PLL1>, <&clk IMX8MQ_AUDIO_PLL2>;
+ assigned-clock-rates = <786432000>, <722534400>;
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec1>;
+ phy-mode = "rgmii-id";
+ phy-handle = <ðphy0>;
+ fsl,magic-packet;
+ phy-supply = <®_3v3_p>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+ };
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ pmic: pmic@4b {
+ compatible = "rohm,bd71837";
+ reg = <0x4b>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pmic>;
+ clocks = <&pmic_osc>;
+ clock-names = "osc";
+ clock-output-names = "pmic_clk";
+ interrupt-parent = <&gpio1>;
+ interrupts = <3 GPIO_ACTIVE_LOW>;
+ interrupt-names = "irq";
+ rohm,reset-snvs-powered;
+
+ regulators {
+ buck1_reg: BUCK1 {
+ regulator-name = "buck1";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ regulator-ramp-delay = <1250>;
+ rohm,dvs-run-voltage = <900000>;
+ rohm,dvs-idle-voltage = <850000>;
+ rohm,dvs-suspend-voltage = <800000>;
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "buck2";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ regulator-ramp-delay = <1250>;
+ rohm,dvs-run-voltage = <1000000>;
+ rohm,dvs-idle-voltage = <900000>;
+ };
+
+ buck3_reg: BUCK3 {
+ regulator-name = "buck3";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ rohm,dvs-run-voltage = <1000000>;
+ };
+
+ buck4_reg: BUCK4 {
+ regulator-name = "buck4";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ rohm,dvs-run-voltage = <1000000>;
+ };
+
+ buck5_reg: BUCK5 {
+ regulator-name = "buck5";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-boot-on;
+ };
+
+ buck6_reg: BUCK6 {
+ regulator-name = "buck6";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+
+ buck7_reg: BUCK7 {
+ regulator-name = "buck7";
+ regulator-min-microvolt = <1605000>;
+ regulator-max-microvolt = <1995000>;
+ regulator-boot-on;
+ };
+
+ buck8_reg: BUCK8 {
+ regulator-name = "buck8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-boot-on;
+ };
+
+ ldo1_reg: LDO1 {
+ regulator-name = "ldo1";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ /* leave on for snvs power button */
+ regulator-always-on;
+ };
+
+ ldo2_reg: LDO2 {
+ regulator-name = "ldo2";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ /* leave on for snvs power button */
+ regulator-always-on;
+ };
+
+ ldo3_reg: LDO3 {
+ regulator-name = "ldo3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+
+ ldo4_reg: LDO4 {
+ regulator-name = "ldo4";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ };
+
+ ldo5_reg: LDO5 {
+ regulator-name = "ldo5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo6_reg: LDO6 {
+ regulator-name = "ldo6";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ };
+
+ ldo7_reg: LDO7 {
+ regulator-name = "ldo7";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+ };
+ };
+
+ typec_ptn5100: usb_typec@52 {
+ compatible = "nxp,ptn5110";
+ reg = <0x52>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_typec>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+
+ connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ data-role = "dual";
+ power-role = "dual";
+ try-power-role = "sink";
+ source-pdos = <PDO_FIXED(5000, 2000,
+ PDO_FIXED_USB_COMM |
+ PDO_FIXED_DUAL_ROLE |
+ PDO_FIXED_DATA_SWAP )>;
+ sink-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM |
+ PDO_FIXED_DUAL_ROLE |
+ PDO_FIXED_DATA_SWAP )
+ PDO_VAR(5000, 12000, 2000)>;
+ op-sink-microwatt = <10000000>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ usb_con_hs: endpoint {
+ remote-endpoint = <&typec_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ usb_con_ss: endpoint {
+ remote-endpoint = <&typec_ss>;
+ };
+ };
+ };
+ };
+ };
+
+ rtc@68 {
+ compatible = "microcrystal,rv4162";
+ reg = <0x68>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rtc>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ charger@6b { /* bq25896 */
+ compatible = "ti,bq25890";
+ reg = <0x6b>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_charger>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+ ti,battery-regulation-voltage = <4192000>; /* 4.192V */
+ ti,charge-current = <1600000>; /* 1.6A */
+ ti,termination-current = <66000>; /* 66mA */
+ ti,precharge-current = <130000>; /* 130mA */
+ ti,minimum-sys-voltage = <3000000>; /* 3V */
+ ti,boost-voltage = <5000000>; /* 5V */
+ ti,boost-max-current = <50000>; /* 50mA */
+ };
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ magnetometer@1e {
+ compatible = "st,lsm9ds1-magn";
+ reg = <0x1e>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_imu>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+ vdd-supply = <®_3v3_p>;
+ vddio-supply = <®_3v3_p>;
+ };
+
+ touchscreen@5d {
+ compatible = "goodix,gt5688";
+ reg = <0x5d>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ts>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+ irq-gpios = <&gpio3 0 GPIO_ACTIVE_HIGH>;
+ touchscreen-size-x = <720>;
+ touchscreen-size-y = <1440>;
+ AVDD28-supply = <®_2v8_p>;
+ VDDIO-supply = <®_1v8_p>;
+ };
+};
+
+&iomuxc {
+ pinctrl_bl: blgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO01_PWM1_OUT 0x6 /* DSI_BL_PWM */
+ >;
+ };
+
+ pinctrl_bt: btgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_NAND_DATA05_GPIO3_IO11 0x16 /* nBT_DISABLE */
+ MX8MQ_IOMUXC_NAND_DATA01_GPIO3_IO7 0x10 /* BT_HOST_WAKE */
+ >;
+ };
+
+ pinctrl_charger: chargergrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SAI5_MCLK_GPIO3_IO25 0x80 /* CHRG_nINT */
+ >;
+ };
+
+ pinctrl_fec1: fec1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC 0x3
+ MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3
+ MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
+ MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
+ MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
+ MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
+ MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
+ MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
+ MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
+ MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
+ MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
+ MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
+ MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
+ MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
+ MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19
+ MX8MQ_IOMUXC_GPIO1_IO15_CCMSRCGPCMIX_CLKO2 0x1f
+ >;
+ };
+
+ pinctrl_ts: tsgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_NAND_ALE_GPIO3_IO0 0x16 /* TOUCH INT */
+ MX8MQ_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x19 /* TOUCH RST */
+ >;
+ };
+
+ pinctrl_gpio_leds: gpioledgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO13_GPIO1_IO13 0x16
+ >;
+ };
+
+ pinctrl_gpio_keys: gpiokeygrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SAI2_RXFS_GPIO4_IO21 0x16
+ MX8MQ_IOMUXC_SAI2_RXC_GPIO4_IO22 0x16
+ MX8MQ_IOMUXC_SAI5_RXC_GPIO3_IO20 0x180 /* HP_DET */
+ >;
+ };
+
+ pinctrl_haptic: hapticgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SPDIF_RX_GPIO5_IO4 0xc6 /* nHAPTIC */
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL 0x4000001f
+ MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA 0x4000001f
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL 0x4000001f
+ MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA 0x4000001f
+ >;
+ };
+
+ pinctrl_imu: imugrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SAI5_RXFS_GPIO3_IO19 0x8 /* IMU_INT */
+ >;
+ };
+
+ pinctrl_pmic: pmicgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x80 /* PMIC intr */
+ >;
+ };
+
+ pinctrl_pwr_en: pwrengrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x06
+ >;
+ };
+
+ pinctrl_rtc: rtcgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SAI3_RXC_GPIO4_IO29 0x80 /* RTC intr */
+ >;
+ };
+
+ pinctrl_typec: typecgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_NAND_DATA06_GPIO3_IO12 0x16
+ MX8MQ_IOMUXC_NAND_CE0_B_GPIO3_IO1 0x80
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX 0x49
+ MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX 0x49
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX 0x49
+ MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX 0x49
+ MX8MQ_IOMUXC_UART4_RXD_UART2_DCE_CTS_B 0x49
+ MX8MQ_IOMUXC_UART4_TXD_UART2_DCE_RTS_B 0x49
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART3_RXD_UART3_DCE_RX 0x49
+ MX8MQ_IOMUXC_UART3_TXD_UART3_DCE_TX 0x49
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_ECSPI2_SCLK_UART4_DCE_RX 0x49
+ MX8MQ_IOMUXC_ECSPI2_MOSI_UART4_DCE_TX 0x49
+ MX8MQ_IOMUXC_ECSPI2_MISO_UART4_DCE_CTS_B 0x49
+ MX8MQ_IOMUXC_ECSPI2_SS0_UART4_DCE_RTS_B 0x49
+ MX8MQ_IOMUXC_GPIO1_IO00_ANAMIX_REF_CLK_32K 0x49
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x83
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc3
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc3
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc3
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc3
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc3
+ MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc3
+ MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc3
+ MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc3
+ MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc3
+ MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x83
+ MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x8d
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xcd
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xcd
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xcd
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xcd
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xcd
+ MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xcd
+ MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xcd
+ MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xcd
+ MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xcd
+ MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x8d
+ MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x9f
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xdf
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xdf
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xdf
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xdf
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xdf
+ MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xdf
+ MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xdf
+ MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xdf
+ MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xdf
+ MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x9f
+ MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1
+ >;
+ };
+
+ pinctrl_usdhc2_pwr: usdhc2grppwr {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41
+ >;
+ };
+
+ pinctrl_usdhc2_gpio: usdhc2grpgpio {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_WP_GPIO2_IO20 0x80 /* WIFI_WAKE */
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x83
+ MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc3
+ MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc3
+ MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc3
+ MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc3
+ MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc3
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x8d
+ MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xcd
+ MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xcd
+ MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xcd
+ MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xcd
+ MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xcd
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x9f
+ MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xcf
+ MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xcf
+ MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xcf
+ MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xcf
+ MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xcf
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6
+ >;
+ };
+
+ pinctrl_wifi_pwr_en: wifipwrengrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_NAND_CLE_GPIO3_IO5 0x06
+ >;
+ };
+
+ pinctrl_wwan: wwangrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_NAND_CE3_B_GPIO3_IO4 0x09 /* nWWAN_DISABLE */
+ MX8MQ_IOMUXC_NAND_DATA02_GPIO3_IO8 0x80 /* nWoWWAN */
+ MX8MQ_IOMUXC_NAND_DATA03_GPIO3_IO9 0x19 /* WWAN_RESET */
+ >;
+ };
+};
+
+&pgc_gpu {
+ power-supply = <&buck3_reg>;
+};
+
+&pgc_vpu {
+ power-supply = <&buck4_reg>;
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_bl>;
+ status = "okay";
+};
+
+
+&uart1 { /* console */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart3 { /* GNSS */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+&uart4 { /* BT */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>, <&pinctrl_bt>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&usb3_phy0 {
+ status = "okay";
+};
+
+&usb3_phy1 {
+ vbus-supply = <®_5v_p>;
+ status = "okay";
+};
+
+&usb_dwc3_0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ dr_mode = "otg";
+ status = "okay";
+
+ port@0 {
+ reg = <0>;
+
+ typec_hs: endpoint {
+ remote-endpoint = <&usb_con_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ typec_ss: endpoint {
+ remote-endpoint = <&usb_con_ss>;
+ };
+ };
+};
+
+&usb_dwc3_1 {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+ bus-width = <4>;
+ vmmc-supply = <®_usdhc2_vmmc>;
+ power-supply = <&wifi_pwr_en>;
+ non-removable;
+ disable-wp;
+ cap-sdio-irq;
+ keep-power-in-suspend;
+ wakeup-source;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
--
2.17.1
Add an entry for Purism, SPC
Signed-off-by: Angus Ainslie (Purism) <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
---
Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 64854a9e4c57..8835ef3aae4f 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -735,6 +735,8 @@ patternProperties:
description: PROBOX2 (by W2COMP Co., Ltd.)
"^pulsedlight,.*":
description: PulsedLight, Inc
+ "^purism,.*":
+ description: Purism, SPC
"^qca,.*":
description: Qualcomm Atheros, Inc.
"^qcom,.*":
--
2.17.1
Add an entry for imx8mq based boards
Signed-off-by: Angus Ainslie (Purism) <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
---
Documentation/devicetree/bindings/arm/fsl.yaml | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 407138ebc0d0..41364b127200 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -177,6 +177,13 @@ properties:
- fsl,imx8mm-evk # i.MX8MM EVK Board
- const: fsl,imx8mm
+ - description: i.MX8MQ based Boards
+ items:
+ - enum:
+ - fsl,imx8mq-evk # i.MX8MQ EVK Board
+ - purism,librem5-devkit # Purism Librem5 devkit
+ - const: fsl,imx8mq
+
- description: i.MX8QXP based Boards
items:
- enum:
--
2.17.1
On Mon 2019-06-17 07:52:13, Angus Ainslie (Purism) wrote:
> This is for the development kit board for the Librem 5. The current level
> of support yields a working console and is able to boot userspace from
> the network or eMMC.
>
> Additional subsystems that are active :
>
> - Both USB ports
> - SD card socket
> - WiFi usdhc
> - WWAN modem
> - GNSS
> - GPIO keys
> - LEDs
> - gyro
> - magnetometer
> - touchscreen
> - pwm
> - backlight
> - haptic motor
>
> Signed-off-by: Angus Ainslie (Purism) <[email protected]>
> Reviewed-by: Fabio Estevam <[email protected]>
Reviewed-by: Pavel Machek <[email protected]>
--
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
On Mon, Jun 17, 2019 at 07:52:12AM -0600, Angus Ainslie (Purism) wrote:
> Angus Ainslie (Purism) (3):
> arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit
> dt-bindings: Add an entry for Purism SPC
> dt-bindings: arm: fsl: Add the imx8mq boards
Applied all, thanks.
On 2019-06-18 07:20, Shawn Guo wrote:
> On Mon, Jun 17, 2019 at 07:52:12AM -0600, Angus Ainslie (Purism) wrote:
>> Angus Ainslie (Purism) (3):
>> arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit
>> dt-bindings: Add an entry for Purism SPC
>> dt-bindings: arm: fsl: Add the imx8mq boards
>
> Applied all, thanks.
Thanks Shawn !