2019-06-29 10:31:32

by Anson Huang

[permalink] [raw]
Subject: [PATCH V2 1/2] arm64: dts: imx8mm: Correct OPP table according to latest datasheet

From: Anson Huang <[email protected]>

According to latest datasheet (Rev.0.2, 04/2019) from below links,
1.8GHz is ONLY available for consumer part, so the market segment
bits for 1.8GHz opp should ONLY available for consumer part accordingly.

https://www.nxp.com/docs/en/data-sheet/IMX8MMIEC.pdf
https://www.nxp.com/docs/en/data-sheet/IMX8MMCEC.pdf

Fixes: f403a26c865b (arm64: dts: imx8mm: Add cpu speed grading and all OPPs)
Signed-off-by: Anson Huang <[email protected]>
---
Changes since V1:
- remove the comment to avoid any confusion.
---
arch/arm64/boot/dts/freescale/imx8mm.dtsi | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
index 70de15c..f0ac027 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
@@ -134,8 +134,7 @@
opp-1800000000 {
opp-hz = /bits/ 64 <1800000000>;
opp-microvolt = <1000000>;
- /* Consumer only but rely on speed grading */
- opp-supported-hw = <0x8>, <0x7>;
+ opp-supported-hw = <0x8>, <0x3>;
clock-latency-ns = <150000>;
};
};
--
2.7.4


2019-06-29 10:31:59

by Anson Huang

[permalink] [raw]
Subject: [PATCH V2 2/2] arm64: dts: imx8mq: Correct OPP table according to latest datasheet

From: Anson Huang <[email protected]>

According to latest datasheet (Rev.1, 10/2018) from below links,
in the consumer datasheet, 1.5GHz is mentioned as highest opp but
depends on speed grading fuse, and in the industrial datasheet,
1.3GHz is mentioned as highest opp but depends on speed grading
fuse. 1.5GHz and 1.3GHz opp use same voltage, so no need for
consumer part to support 1.3GHz opp, with same voltage, CPU should
run at highest frequency in order to go into idle as quick as
possible, this can save power.

That means for consumer part, 1GHz/1.5GHz are supported, for
industrial part, 800MHz/1.3GHz are supported, and then check the
speed grading fuse to limit the highest CPU frequency further.
Correct the market segment bits in opp table to make them work
according to datasheets.

https://www.nxp.com/docs/en/data-sheet/IMX8MDQLQIEC.pdf
https://www.nxp.com/docs/en/data-sheet/IMX8MDQLQCEC.pdf

Fixes: 12629c5c3749 ("arm64: dts: imx8mq: Add cpu speed grading and all OPPs")
Signed-off-by: Anson Huang <[email protected]>
---
Changes since V1:
- remove the comment to avoid any confusion.
---
arch/arm64/boot/dts/freescale/imx8mq.dtsi | 5 ++---
1 file changed, 2 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
index 9d99191..477c523 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
@@ -169,15 +169,14 @@
opp-1300000000 {
opp-hz = /bits/ 64 <1300000000>;
opp-microvolt = <1000000>;
- opp-supported-hw = <0xc>, <0x7>;
+ opp-supported-hw = <0xc>, <0x4>;
clock-latency-ns = <150000>;
};

opp-1500000000 {
opp-hz = /bits/ 64 <1500000000>;
opp-microvolt = <1000000>;
- /* Consumer only but rely on speed grading */
- opp-supported-hw = <0x8>, <0x7>;
+ opp-supported-hw = <0x8>, <0x3>;
clock-latency-ns = <150000>;
};
};
--
2.7.4

2019-07-01 15:16:56

by Leonard Crestez

[permalink] [raw]
Subject: Re: [PATCH V2 1/2] arm64: dts: imx8mm: Correct OPP table according to latest datasheet

On 6/29/2019 1:31 PM, [email protected] wrote:
> From: Anson Huang <[email protected]>
>
> According to latest datasheet (Rev.0.2, 04/2019) from below links,
> 1.8GHz is ONLY available for consumer part, so the market segment
> bits for 1.8GHz opp should ONLY available for consumer part accordingly.
> > Fixes: f403a26c865b (arm64: dts: imx8mm: Add cpu speed grading and
all OPPs)
> Signed-off-by: Anson Huang <[email protected]>

For both:
Reviewed-by: Leonard Crestez <[email protected]>

The vendor tree goes through a lot of testing so switching to the exact
speed grading interpretation from there does make sense.

2019-07-18 08:06:24

by Shawn Guo

[permalink] [raw]
Subject: Re: [PATCH V2 1/2] arm64: dts: imx8mm: Correct OPP table according to latest datasheet

On Sat, Jun 29, 2019 at 06:21:56PM +0800, [email protected] wrote:
> From: Anson Huang <[email protected]>
>
> According to latest datasheet (Rev.0.2, 04/2019) from below links,
> 1.8GHz is ONLY available for consumer part, so the market segment
> bits for 1.8GHz opp should ONLY available for consumer part accordingly.
>
> https://www.nxp.com/docs/en/data-sheet/IMX8MMIEC.pdf
> https://www.nxp.com/docs/en/data-sheet/IMX8MMCEC.pdf
>
> Fixes: f403a26c865b (arm64: dts: imx8mm: Add cpu speed grading and all OPPs)
> Signed-off-by: Anson Huang <[email protected]>

Applied both, thanks.